VDSL2-LINE-MIB
433 objects
This document defines a Management Information Base (MIB) module for use with network management protocols in the Internet community for the purpose of managing VDSL2, ADSL, ADSL2, and ADSL2+ lines. The MIB module described in RFC 2662 [RFC2662] defines objects used for managing Asymmetric Bit-Rate DSL (ADSL) interfaces per [T1E1.413], [G.992.1], and [G.992.2]. These object descriptions are based upon the specifications for the ADSL Embedded Operations Channel (EOC) as defined in American National Standards Institute (ANSI) T1E1.413 [T1E1.413] and International Telecommunication Union (ITU-T) G.992.1 [G.992.1] and G.992.2 [G.992.2]. The MIB module described in RFC 4706 [RFC4706] defines objects used for managing ADSL2 interfaces per [G.992.3] and [G.992.4], and ADSL2+ interfaces per [G.992.5]. That MIB is also capable of managing ADSL interfaces per [T1E1.413], [G.992.1], and [G.992.2]. This document does not obsolete RFC 2662 [RFC2662] or RFC 4706 [RFC4706], but rather provides a more comprehensive management model that manages VDSL2 interfaces per G.993.2 [G.993.2] as well as ADSL, ADSL2, and ADSL2+ technologies per T1E1.413, G.992.1, G.992.2, G.992.3, G.992.4, and G.992.5 ([T1E1.413], [G.992.1], [G.992.2], [G.992.3], [G.992.4], and [G.992.5], respectively). Additionally, the management framework for VDSL2 lines specified by the Digital Subscriber Line Forum (DSLF) has been taken into consideration [TR-129]. That framework is based on the ITU-T G.997.1 standard [G.997.1] and its amendment 1 [G.997.1-Am1]. The MIB module is located in the MIB tree under MIB 2 transmission, as discussed in the MIB-2 Integration (RFC 2863 [RFC2863]) section of this document. Copyright (c) 2009 IETF Trust and the persons identified as authors of the code. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: - Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. - Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. - Neither the name of Internet Society, IETF or IETF Trust, nor the names of specific contributors, may be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS 'AS IS' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. This version of this MIB module is part of RFC 5650; see the RFC itself for full legal notices.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.2.1.10.251 | Identityvdsl2MIB | This document defines a Management Information Base (MIB) module for use with network management protocols in the Internet community for the purpose of managin… | ||
| 1.3.6.1.2.1.10.251.0 | Nodexdsl2Notifications | |||
| 1.3.6.1.2.1.10.251.0.1 | Notificationxdsl2LinePerfFECSThreshXtuc | current | This notification indicates that the FEC seconds threshold has been reached/exceeded for the referred xTU-C. | |
| 1.3.6.1.2.1.10.251.0.2 | Notificationxdsl2LinePerfFECSThreshXtur | current | This notification indicates that the FEC seconds threshold has been reached/exceeded for the referred xTU-R. | |
| 1.3.6.1.2.1.10.251.0.3 | Notificationxdsl2LinePerfESThreshXtuc | current | This notification indicates that the errored seconds threshold has been reached/exceeded for the referred xTU-C. | |
| 1.3.6.1.2.1.10.251.0.4 | Notificationxdsl2LinePerfESThreshXtur | current | This notification indicates that the errored seconds threshold has been reached/exceeded for the referred xTU-R. | |
| 1.3.6.1.2.1.10.251.0.5 | Notificationxdsl2LinePerfSESThreshXtuc | current | This notification indicates that the severely errored seconds threshold has been reached/exceeded for the referred xTU-C. | |
| 1.3.6.1.2.1.10.251.0.6 | Notificationxdsl2LinePerfSESThreshXtur | current | This notification indicates that the severely errored seconds threshold has been reached/exceeded for the referred xTU-R. | |
| 1.3.6.1.2.1.10.251.0.7 | Notificationxdsl2LinePerfLOSSThreshXtuc | current | This notification indicates that the LOS seconds threshold has been reached/exceeded for the referred xTU-C. | |
| 1.3.6.1.2.1.10.251.0.8 | Notificationxdsl2LinePerfLOSSThreshXtur | current | This notification indicates that the LOS seconds threshold has been reached/exceeded for the referred xTU-R. | |
| 1.3.6.1.2.1.10.251.0.9 | Notificationxdsl2LinePerfUASThreshXtuc | current | This notification indicates that the unavailable seconds threshold has been reached/exceeded for the referred xTU-C. | |
| 1.3.6.1.2.1.10.251.0.10 | Notificationxdsl2LinePerfUASThreshXtur | current | This notification indicates that the unavailable seconds threshold has been reached/exceeded for the referred xTU-R. | |
| 1.3.6.1.2.1.10.251.0.11 | Notificationxdsl2LinePerfCodingViolationsThreshXtuc | current | This notification indicates that the coding violations threshold has been reached/exceeded for the referred xTU-C. | |
| 1.3.6.1.2.1.10.251.0.12 | Notificationxdsl2LinePerfCodingViolationsThreshXtur | current | This notification indicates that the coding violations threshold has been reached/exceeded for the referred xTU-R. | |
| 1.3.6.1.2.1.10.251.0.13 | Notificationxdsl2LinePerfCorrectedThreshXtuc | current | This notification indicates that the corrected blocks (FEC events) threshold has been reached/exceeded for the referred xTU-C. | |
| 1.3.6.1.2.1.10.251.0.14 | Notificationxdsl2LinePerfCorrectedThreshXtur | current | This notification indicates that the corrected blocks (FEC events) threshold has been reached/exceeded for the referred xTU-R. | |
| 1.3.6.1.2.1.10.251.0.15 | Notificationxdsl2LinePerfFailedFullInitThresh | current | This notification indicates that the failed full initializations threshold has been reached/exceeded for the referred ADSL/ADSL2 or ADSL2 line. | |
| 1.3.6.1.2.1.10.251.0.16 | Notificationxdsl2LinePerfFailedShortInitThresh | current | This notification indicates that the failed short initializations threshold has been reached/exceeded for the referred VDSL2/ADSL/ADSL2 or ADSL2+ line. | |
| 1.3.6.1.2.1.10.251.0.17 | Notificationxdsl2LineStatusChangeXtuc | current | This notification indicates that a status change is detected for the referred xTU-C. | |
| 1.3.6.1.2.1.10.251.0.18 | Notificationxdsl2LineStatusChangeXtur | current | This notification indicates that a status change is detected for the referred xTU-R. | |
| 1.3.6.1.2.1.10.251.1 | Nodexdsl2Objects | |||
| 1.3.6.1.2.1.10.251.1.1 | Nodexdsl2Line | |||
| 1.3.6.1.2.1.10.251.1.1.1 | Tablexdsl2LineTable | not-accessible | current | The table xdsl2LineTable contains configuration, command and status parameters of the VDSL2/ADSL/ADSL2 or ADSL2+ line. Several objects in this table MUST be ma… |
| 1.3.6.1.2.1.10.251.1.1.1.1 | Rowxdsl2LineEntry | not-accessible | current | The index of this table is an interface index where the interface has an ifType of vdsl2(251). |
| 1.3.6.1.2.1.10.251.1.1.1.1.1 | Columnxdsl2LineConfTemplate | read-write | current | The value of this object identifies the row in the xDSL2 Line Configuration Template Table, xdsl2LineConfTemplateTable, that applies for this line. This object… |
| 1.3.6.1.2.1.10.251.1.1.1.1.2 | Columnxdsl2LineConfFallbackTemplate | read-write | current | This object is used to identify the template that will be used if the xDSL2 line fails to operate using the primary template. The primary template is identifie… |
| 1.3.6.1.2.1.10.251.1.1.1.1.3 | Columnxdsl2LineAlarmConfTemplate | read-write | current | The value of this object identifies the row in the xDSL2 Line Alarm Configuration Template Table, xdsl2LineAlarmConfTemplateTable, which applies to this line. … |
| 1.3.6.1.2.1.10.251.1.1.1.1.4 | Columnxdsl2LineCmndConfPmsf | read-write | current | Power management state forced (PMSF). Defines the line states to be forced by the near-end xTU on this line. This object MUST be maintained in a persistent man… |
| 1.3.6.1.2.1.10.251.1.1.1.1.5 | Columnxdsl2LineCmndConfLdsf | read-write | current | Loop diagnostic state forced (LDSF). Defines whether the line should be forced into the loop diagnostics mode by the near-end xTU of this line. Note that a loo… |
| 1.3.6.1.2.1.10.251.1.1.1.1.6 | Columnxdsl2LineCmndConfLdsfFailReason | read-only | current | The status of the most recent occasion when the loop diagnostics state forced (LDSF) command was issued for the associated line. |
| 1.3.6.1.2.1.10.251.1.1.1.1.7 | Columnxdsl2LineCmndConfBpsc | read-write | current | Request a bits-per-subcarrier measurement to be made. A request for a bits-per-subcarrier measurement is made by setting this object to the value of 'measure'.… |
| 1.3.6.1.2.1.10.251.1.1.1.1.8 | Columnxdsl2LineCmndConfBpscFailReason | read-only | current | The status of the most recent bits-per-subcarrier measurement request issued for the associated line. |
| 1.3.6.1.2.1.10.251.1.1.1.1.9 | Columnxdsl2LineCmndConfBpscRequests | read-only | current | Measurement request counter. This counter is incremented by one every time a request for a bits-per-subcarrier measurement is made. A measurement request is ma… |
| 1.3.6.1.2.1.10.251.1.1.1.1.10 | Columnxdsl2LineCmndAutomodeColdStart | read-write | current | Automode cold start forced. This parameter is defined in order to improve testing of the performance of xTUs supporting automode when it is enabled in the MIB.… |
| 1.3.6.1.2.1.10.251.1.1.1.1.11 | Columnxdsl2LineCmndConfReset | read-write | current | Request a line reset to occur. If this object is set to the value of 'reset', then force the line to reset (i.e., the modems will retrain). When the line has s… |
| 1.3.6.1.2.1.10.251.1.1.1.1.12 | Columnxdsl2LineStatusActTemplate | read-only | current | This object is used to identify the template that is currently in use for this line. This object is updated when a successful line initialization occurs. This … |
| 1.3.6.1.2.1.10.251.1.1.1.1.13 | Columnxdsl2LineStatusXtuTransSys | read-only | current | The xTU Transmission System (xTS) in use. It is coded in a bitmap representation with one bit set to '1' (the selected coding for the DSL line). This parameter… |
| 1.3.6.1.2.1.10.251.1.1.1.1.14 | Columnxdsl2LineStatusPwrMngState | read-only | current | The current power management state. |
| 1.3.6.1.2.1.10.251.1.1.1.1.15 | Columnxdsl2LineStatusInitResult | read-only | current | Indicates the result of the last full initialization performed on the line. |
| 1.3.6.1.2.1.10.251.1.1.1.1.16 | Columnxdsl2LineStatusLastStateDs | read-only | current | The last successful transmitted initialization state in the downstream direction in the last full initialization performed on the line. |
| 1.3.6.1.2.1.10.251.1.1.1.1.17 | Columnxdsl2LineStatusLastStateUs | read-only | current | The last successful transmitted initialization state in the upstream direction in the last full initialization performed on the line. |
| 1.3.6.1.2.1.10.251.1.1.1.1.18 | Columnxdsl2LineStatusXtur | read-only | current | Indicates the current state (existing failures) of the xTU-R. This is a bitmap of possible conditions. |
| 1.3.6.1.2.1.10.251.1.1.1.1.19 | Columnxdsl2LineStatusXtuc | read-only | current | Indicates the current state (existing failures) of the xTU-C. This is a bitmap of possible conditions. |
| 1.3.6.1.2.1.10.251.1.1.1.1.20 | Columnxdsl2LineStatusAttainableRateDs | read-only | current | Maximum Attainable Data Rate Downstream. The maximum downstream net data rate currently attainable by the xTU-C transmitter and the xTU-R receiver, coded in bi… |
| 1.3.6.1.2.1.10.251.1.1.1.1.21 | Columnxdsl2LineStatusAttainableRateUs | read-only | current | Maximum Attainable Data Rate Upstream. The maximum upstream net data rate currently attainable by the xTU-R transmitter and the xTU-C receiver, coded in bit/s. |
| 1.3.6.1.2.1.10.251.1.1.1.1.22 | Columnxdsl2LineStatusActPsdDs | read-only | current | Actual Power Spectral Density (PSD) Downstream. The average downstream transmit PSD over the subcarriers used for downstream. It ranges from -900 to 0 units of… |
| 1.3.6.1.2.1.10.251.1.1.1.1.23 | Columnxdsl2LineStatusActPsdUs | read-only | current | Actual Power Spectral Density (PSD) Upstream. The average upstream transmit PSD over the subcarriers used for upstream. It ranges from -900 to 0 units of 0.1 d… |
| 1.3.6.1.2.1.10.251.1.1.1.1.24 | Columnxdsl2LineStatusActAtpDs | read-only | current | Actual Aggregate Transmit Power Downstream. The total amount of transmit power delivered by the xTU-C at the U-C reference point, at the instant of measurement… |
| 1.3.6.1.2.1.10.251.1.1.1.1.25 | Columnxdsl2LineStatusActAtpUs | read-only | current | Actual Aggregate Transmit Power Upstream. The total amount of transmit power delivered by the xTU-R at the U-R reference point, at the instant of measurement. … |
| 1.3.6.1.2.1.10.251.1.1.1.1.26 | Columnxdsl2LineStatusActProfile | read-only | current | The G.993.2 profile in use. The configuration parameter xdsl2LConfProfProfiles defines the set of allowed G.993.2 profiles. This parameter indicates the profil… |
| 1.3.6.1.2.1.10.251.1.1.1.1.27 | Columnxdsl2LineStatusActLimitMask | read-only | current | The Limit PSD mask and band plan in use. The configuration parameter xdsl2LConfProfLimitMask defines the set of allowed G.993.2 limit PSD masks. This parameter… |
| 1.3.6.1.2.1.10.251.1.1.1.1.28 | Columnxdsl2LineStatusActUs0Mask | read-only | current | The US0 PSD mask in use. The configuration parameter xdsl2LConfProfUs0Mask defines the set of allowed US0 PSD masks. This parameter indicates the US0 PSD mask … |
| 1.3.6.1.2.1.10.251.1.1.1.1.29 | Columnxdsl2LineStatusActSnrModeDs | read-only | current | This parameter indicates if the transmitter-referred virtual noise is active on the line in the downstream direction. The configuration parameter xdsl2LConfPro… |
| 1.3.6.1.2.1.10.251.1.1.1.1.30 | Columnxdsl2LineStatusActSnrModeUs | read-only | current | This parameter indicates if the transmitter-referred virtual noise is active on the line in the upstream direction. The configuration parameter xdsl2LConfProfS… |
| 1.3.6.1.2.1.10.251.1.1.1.1.31 | Columnxdsl2LineStatusElectricalLength | read-only | current | This parameter contains the estimated electrical length expressed in dB at 1 MHz, kl0. This is the final electrical length that would have been sent from the V… |
| 1.3.6.1.2.1.10.251.1.1.1.1.32 | Columnxdsl2LineStatusTssiDs | read-only | current | The transmit spectrum shaping (TSSi) breakpoints expressed as the set of breakpoints exchanged during G.994.1 (Downstream). |
| 1.3.6.1.2.1.10.251.1.1.1.1.33 | Columnxdsl2LineStatusTssiUs | read-only | current | The transmit spectrum shaping (TSSi) breakpoints expressed as the set of breakpoints exchanged during G.994.1 (Upstream). |
| 1.3.6.1.2.1.10.251.1.1.1.1.34 | Columnxdsl2LineStatusMrefPsdDs | read-only | current | The MEDLEY Reference PSD status parameters in the downstream direction expressed as the set of breakpoints exchanged at initialization. |
| 1.3.6.1.2.1.10.251.1.1.1.1.35 | Columnxdsl2LineStatusMrefPsdUs | read-only | current | The MEDLEY Reference PSD status parameters in the upstream direction expressed as the set of breakpoints exchanged at initialization. |
| 1.3.6.1.2.1.10.251.1.1.1.1.36 | Columnxdsl2LineStatusTrellisDs | read-only | current | This parameter reports whether trellis coding is in use in the downstream direction. |
| 1.3.6.1.2.1.10.251.1.1.1.1.37 | Columnxdsl2LineStatusTrellisUs | read-only | current | This parameter reports whether trellis coding is in use in the upstream direction. |
| 1.3.6.1.2.1.10.251.1.1.1.1.38 | Columnxdsl2LineStatusActualCe | read-only | current | (ACTUALCE) This parameter reports the cyclic extension used on the line. It is coded as an unsigned integer from 2 to 16 in units of N/32 samples, where 2N is … |
| 1.3.6.1.2.1.10.251.1.1.2 | Tablexdsl2LineBandTable | not-accessible | current | The table xdsl2LineBandTable contains the, per-band line status parameters of the VDSL2/ADSL/ADSL2 or ADSL2+ line. The parameters in this table are updated at … |
| 1.3.6.1.2.1.10.251.1.1.2.1 | Rowxdsl2LineBandEntry | not-accessible | current | One index of this table is an interface index where the interface has an ifType of vdsl2(251). A second index of this table is a per-band index covering both V… |
| 1.3.6.1.2.1.10.251.1.1.2.1.1 | Columnxdsl2LineBand | not-accessible | current | Identifies the band(s) associated with this line. For ADSL/ADSL2/ADSL2+, the values 'upstream' and 'downstream' will always be present. For VDSL2, a subset of … |
| 1.3.6.1.2.1.10.251.1.1.2.1.2 | Columnxdsl2LineBandStatusLnAtten | read-only | current | Line Attenuation. When referring to a band in the downstream direction, it is the measured difference in the total power transmitted by the xTU-C and the total… |
| 1.3.6.1.2.1.10.251.1.1.2.1.3 | Columnxdsl2LineBandStatusSigAtten | read-only | current | Signal Attenuation. When referring to a band in the downstream direction, it is the measured difference in the total power transmitted by the xTU-C and the tot… |
| 1.3.6.1.2.1.10.251.1.1.2.1.4 | Columnxdsl2LineBandStatusSnrMargin | read-only | current | SNR Margin is the maximum increase in dB of the noise power received at the xTU (xTU-R for a band in the downstream direction and xTU-C for a band in the upstr… |
| 1.3.6.1.2.1.10.251.1.2 | Nodexdsl2Status | |||
| 1.3.6.1.2.1.10.251.1.2.1 | Tablexdsl2LineSegmentTable | not-accessible | current | The table xdsl2LineSegmentTable contains status parameters of VDSL2/ADSL/ADSL2 and ADSL2+ subcarriers. The parameters in this table are updated when a measurem… |
| 1.3.6.1.2.1.10.251.1.2.1.1 | Rowxdsl2LineSegmentEntry | not-accessible | current | The table xdsl2LineSegmentEntry contains status parameters of VDSL2/ADSL/ADSL2 and ADSL2+ subcarriers. Objects in the table refer to NSus and NSds. For G.993.2… |
| 1.3.6.1.2.1.10.251.1.2.1.1.1 | Columnxdsl2LineSegmentDirection | not-accessible | current | The direction of the subcarrier either upstream or downstream. |
| 1.3.6.1.2.1.10.251.1.2.1.1.2 | Columnxdsl2LineSegment | not-accessible | current | The segment of the subcarriers status information provided by this row. Status parameters in this table are retrieved in segments. The first segment of the sta… |
| 1.3.6.1.2.1.10.251.1.2.1.1.3 | Columnxdsl2LineSegmentBitsAlloc | read-only | current | The bits allocation per subcarrier. An array of 256 octets (512 nibbles), designed for supporting up to 512 (downstream) subcarriers. When more than 512 subcar… |
| 1.3.6.1.2.1.10.251.1.2.1.1.4 | Columnxdsl2LineSegmentRowStatus | read-write | current | Row Status. The SNMP agent will create a row in this table for storing the results of a measurement performed on the associated line, if the row does not alrea… |
| 1.3.6.1.2.1.10.251.1.2.2 | Tablexdsl2ChannelStatusTable | not-accessible | current | The table xdsl2ChannelStatusTable contains status parameters of VDSL2/ADSL/ADSL2 or ADSL2+ channel. This table contains live data from equipment. |
| 1.3.6.1.2.1.10.251.1.2.2.1 | Rowxdsl2ChannelStatusEntry | not-accessible | current | One index of this table is an interface index where the interface has an ifType of a DSL channel. A second index of this table is the termination unit. |
| 1.3.6.1.2.1.10.251.1.2.2.1.1 | Columnxdsl2ChStatusUnit | not-accessible | current | The termination unit. |
| 1.3.6.1.2.1.10.251.1.2.2.1.2 | Columnxdsl2ChStatusActDataRate | read-only | current | The actual net data rate at which the bearer channel is operating, if in L0 power management state. In L1 or L2 states, it relates to the previous L0 state. Th… |
| 1.3.6.1.2.1.10.251.1.2.2.1.3 | Columnxdsl2ChStatusPrevDataRate | read-only | current | The previous net data rate that the bearer channel was operating at just before the latest rate change event. This could be a full or short initialization, fas… |
| 1.3.6.1.2.1.10.251.1.2.2.1.4 | Columnxdsl2ChStatusActDelay | read-only | current | The actual one-way interleaving delay introduced by the PMS-TC in the direction of the bearer channel, if in L0 power management state. In L1 or L2 states, it … |
| 1.3.6.1.2.1.10.251.1.2.2.1.5 | Columnxdsl2ChStatusActInp | read-only | current | Actual impulse noise protection. This parameter reports the actual impulse noise protection (INP) on the bearer channel in the L0 state. In the L1 or L2 state,… |
| 1.3.6.1.2.1.10.251.1.2.2.1.6 | Columnxdsl2ChStatusInpReport | read-only | current | Impulse noise protection reporting mode. |
| 1.3.6.1.2.1.10.251.1.2.2.1.7 | Columnxdsl2ChStatusNFec | read-only | current | Actual size of Reed-Solomon codeword. This parameter reports the actual number of Reed-Solomon redundancy bytes per codeword used in the latency path in which … |
| 1.3.6.1.2.1.10.251.1.2.2.1.8 | Columnxdsl2ChStatusRFec | read-only | current | Actual number of Reed-Solomon redundancy bytes. This parameter reports the actual number of Reed-Solomon redundancy bytes per codeword used in the latency path… |
| 1.3.6.1.2.1.10.251.1.2.2.1.9 | Columnxdsl2ChStatusLSymb | read-only | current | Actual number of bits per symbol. This parameter reports the actual number of bits per symbol assigned to the latency path in which the bearer channel is trans… |
| 1.3.6.1.2.1.10.251.1.2.2.1.10 | Columnxdsl2ChStatusIntlvDepth | read-only | current | Actual interleaving depth. This parameter reports the actual depth of the interleaver used in the latency path in which the bearer channel is transported. The … |
| 1.3.6.1.2.1.10.251.1.2.2.1.11 | Columnxdsl2ChStatusIntlvBlock | read-only | current | Actual interleaving block length. This parameter reports the actual block length of the interleaver used in the latency path in which the bearer channel is tra… |
| 1.3.6.1.2.1.10.251.1.2.2.1.12 | Columnxdsl2ChStatusLPath | read-only | current | Actual latency path. This parameter reports the index of the actual latency path in which the bearer is transported. The valid values are 0, 1, 2 and 3. For G.… |
| 1.3.6.1.2.1.10.251.1.2.2.1.13 | Columnxdsl2ChStatusAtmStatus | read-only | current | Indicates current state (existing failures) of the DSL channel in case its Data Path is ATM. This is a bitmap of possible conditions. In case the channel is no… |
| 1.3.6.1.2.1.10.251.1.2.2.1.14 | Columnxdsl2ChStatusPtmStatus | read-only | current | Indicates current state (existing failures) of the DSL channel in case its Data Path is PTM (Packet Transfer Mode). This is a bitmap of possible conditions. In… |
| 1.3.6.1.2.1.10.251.1.2.3 | Tablexdsl2SCStatusTable | not-accessible | current | The table xdsl2SCStatusTable contains status parameters for VDSL2/ADSL/ADSL2 and ADSL2+ that provide information about the size of parameters in xdsl2SCStatusS… |
| 1.3.6.1.2.1.10.251.1.2.3.1 | Rowxdsl2SCStatusEntry | not-accessible | current | One index of this table is an interface index where the interface has an ifType of vdsl2(251). A second index of this table is the transmission direction. |
| 1.3.6.1.2.1.10.251.1.2.3.1.1 | Columnxdsl2SCStatusDirection | not-accessible | current | The direction of the subcarrier either upstream or downstream. |
| 1.3.6.1.2.1.10.251.1.2.3.1.2 | Columnxdsl2SCStatusLinScale | read-only | current | The scale factor to be applied to the H(f) linear representation values for the respective transmission direction. This parameter is only available after a loo… |
| 1.3.6.1.2.1.10.251.1.2.3.1.3 | Columnxdsl2SCStatusLinScGroupSize | read-only | current | Number of subcarriers per group used to report the H(f) linear representation values for the respective transmission direction. The valid values are 1, 2, 4, a… |
| 1.3.6.1.2.1.10.251.1.2.3.1.4 | Columnxdsl2SCStatusLogMt | read-only | current | This parameter contains the number of symbols used to measure the Hlog(f) values. It is represented as an unsigned integer in the range from 1 to 2^16-1. After… |
| 1.3.6.1.2.1.10.251.1.2.3.1.5 | Columnxdsl2SCStatusLogScGroupSize | read-only | current | Number of subcarriers per group used to report the H(f) logarithmic representation values for the respective transmission direction. The valid values are 1, 2,… |
| 1.3.6.1.2.1.10.251.1.2.3.1.6 | Columnxdsl2SCStatusQlnMt | read-only | current | This parameter contains the number of symbols used to measure the QLN(f) values. It is an unsigned integer in the range from 1 to 2^16-1. After a loop diagnost… |
| 1.3.6.1.2.1.10.251.1.2.3.1.7 | Columnxdsl2SCStatusQlnScGroupSize | read-only | current | Number of subcarriers per group used to report the Quiet Line Noise values for the respective transmission direction. The valid values are 1, 2, 4, and 8. For … |
| 1.3.6.1.2.1.10.251.1.2.3.1.8 | Columnxdsl2SCStatusSnrMtime | read-only | current | This parameter contains the number of symbols used to measure the SNR(f) values. It is an unsigned integer in the range from 1 to 2^16-1. After a loop diagnost… |
| 1.3.6.1.2.1.10.251.1.2.3.1.9 | Columnxdsl2SCStatusSnrScGroupSize | read-only | current | Number of subcarriers per group used to report the SNR values on the respective transmission direction. The valid values are 1, 2, 4, and 8. For ADSL, this par… |
| 1.3.6.1.2.1.10.251.1.2.3.1.10 | Columnxdsl2SCStatusAttainableRate | read-only | current | Maximum Attainable Data Rate. The maximum net data rate currently attainable by the xTU-C transmitter and xTU-R receiver (when referring to downstream directio… |
| 1.3.6.1.2.1.10.251.1.2.3.1.11 | Columnxdsl2SCStatusRowStatus | read-write | current | Row Status. The SNMP agent will create a row in this table for storing the results of a DELT performed on the associated line, if the row does not already exis… |
| 1.3.6.1.2.1.10.251.1.2.4 | Tablexdsl2SCStatusBandTable | not-accessible | current | The table xdsl2SCStatusBandTable contains subcarrier status parameters for VDSL2/ADSL/ADSL2 and ADSL2+ that are grouped per- band. For ADSL/ADSL2/ADSL2+, there… |
| 1.3.6.1.2.1.10.251.1.2.4.1 | Rowxdsl2SCStatusBandEntry | not-accessible | current | One index of this table is an interface index where the interface has an ifType of vdsl2(251). A second index of this table is the transmission band. |
| 1.3.6.1.2.1.10.251.1.2.4.1.1 | Columnxdsl2SCStatusBand | not-accessible | current | The transmission band. |
| 1.3.6.1.2.1.10.251.1.2.4.1.2 | Columnxdsl2SCStatusBandLnAtten | read-only | current | When referring to a band in the downstream direction, it is the measured difference in the total power transmitted by the xTU-C and the total power received by… |
| 1.3.6.1.2.1.10.251.1.2.4.1.3 | Columnxdsl2SCStatusBandSigAtten | read-only | current | When referring to a band in the downstream direction, it is the measured difference in the total power transmitted by the xTU-C and the total power received by… |
| 1.3.6.1.2.1.10.251.1.2.5 | Tablexdsl2SCStatusSegmentTable | not-accessible | current | The table xdsl2SCStatusSegmentTable contains status parameters of VDSL2/ADSL/ADSL2 and ADSL2+ subcarriers. Several objects in the table refer to NSus and NSds.… |
| 1.3.6.1.2.1.10.251.1.2.5.1 | Rowxdsl2SCStatusSegmentEntry | not-accessible | current | One index of this table is an interface index where the interface has an ifType of vdsl2(251). A second index of this table is the transmission direction. A th… |
| 1.3.6.1.2.1.10.251.1.2.5.1.1 | Columnxdsl2SCStatusSegment | not-accessible | current | The segment of the subcarriers status information provided by this row. Several status parameters in this table are retrieved in segments. The first segment of… |
| 1.3.6.1.2.1.10.251.1.2.5.1.2 | Columnxdsl2SCStatusSegmentLinReal | read-only | current | An array of up to 512 complex H(f) linear representation values in linear scale for the respective transmission direction. It is designed to support up to 512 … |
| 1.3.6.1.2.1.10.251.1.2.5.1.3 | Columnxdsl2SCStatusSegmentLinImg | read-only | current | An array of up to 512 complex H(f) linear representation values in linear scale for the respective transmission direction. It is designed to support up to 512 … |
| 1.3.6.1.2.1.10.251.1.2.5.1.4 | Columnxdsl2SCStatusSegmentLog | read-only | current | An array of up to 512 real H(f) logarithmic representation values in dB for the respective transmission direction. It is designed to support up to 512 (downstr… |
| 1.3.6.1.2.1.10.251.1.2.5.1.5 | Columnxdsl2SCStatusSegmentQln | read-only | current | An array of up to 512 real Quiet Line Noise values in dBm/Hz for the respective transmission direction. It is designed for up to 512 (downstream) subcarrier gr… |
| 1.3.6.1.2.1.10.251.1.2.5.1.6 | Columnxdsl2SCStatusSegmentSnr | read-only | current | The SNR Margin per subcarrier group, expressing the ratio between the received signal power and received noise power per subscriber group. It is an array of 51… |
| 1.3.6.1.2.1.10.251.1.2.5.1.7 | Columnxdsl2SCStatusSegmentBitsAlloc | read-only | current | The bits allocation per subcarrier. An array of 256 octets (512 nibbles) designed for supporting up to 512 (downstream) subcarriers. When more than 512 subcarr… |
| 1.3.6.1.2.1.10.251.1.2.5.1.8 | Columnxdsl2SCStatusSegmentGainAlloc | read-only | current | The gain allocation per subcarrier. An array of 512 16-bit values, designed for supporting up to 512 (downstream) subcarriers. When more then 512 subcarriers a… |
| 1.3.6.1.2.1.10.251.1.3 | Nodexdsl2Inventory | |||
| 1.3.6.1.2.1.10.251.1.3.1 | Tablexdsl2LineInventoryTable | not-accessible | current | The table xdsl2LineInventoryTable contains an inventory of the DSL termination unit. |
| 1.3.6.1.2.1.10.251.1.3.1.1 | Rowxdsl2LineInventoryEntry | not-accessible | current | One index of this table is an interface index where the interface has an ifType of vdsl2(251). A second index of this table is the termination unit. |
| 1.3.6.1.2.1.10.251.1.3.1.1.1 | Columnxdsl2LInvUnit | not-accessible | current | The termination unit. |
| 1.3.6.1.2.1.10.251.1.3.1.1.2 | Columnxdsl2LInvG994VendorId | read-only | current | The ADSL Transceiver Unit (ATU) G.994.1 Vendor ID as inserted in the G.994.1 CL/CLR message. It consists of 8 binary octets, including a country code followed … |
| 1.3.6.1.2.1.10.251.1.3.1.1.3 | Columnxdsl2LInvSystemVendorId | read-only | current | The ATU System Vendor ID (identifies the xTU system integrator) as inserted in the Overhead Messages (both xTUs for G.992.3, G.992.4, G.992.5, and G.993.2) or … |
| 1.3.6.1.2.1.10.251.1.3.1.1.4 | Columnxdsl2LInvVersionNumber | read-only | current | The xTU version number (vendor-specific information) as inserted in the Overhead Messages (both xTUs for G.992.3, G.992.4, G.992.5, and G.993.2) or in the Embe… |
| 1.3.6.1.2.1.10.251.1.3.1.1.5 | Columnxdsl2LInvSerialNumber | read-only | current | The xTU serial number (vendor-specific information) as inserted in the Overhead Messages (both xTUs for G.992.3, G.992.4, G.992.5, and G.993.2) or in the Embed… |
| 1.3.6.1.2.1.10.251.1.3.1.1.6 | Columnxdsl2LInvSelfTestResult | read-only | current | The xTU self-test result, coded as a 32-bit value. The most significant octet of the result is '0' if the self-test passed, and '1' if the self-test failed. Th… |
| 1.3.6.1.2.1.10.251.1.3.1.1.7 | Columnxdsl2LInvTransmissionCapabilities | read-only | current | The xTU transmission system capability list of the different coding types. It is coded in a bitmap representation with 1 or more bits set. A bit set to '1' mea… |
| 1.3.6.1.2.1.10.251.1.4 | Nodexdsl2PM | |||
| 1.3.6.1.2.1.10.251.1.4.1 | Nodexdsl2PMLine | |||
| 1.3.6.1.2.1.10.251.1.4.1.1 | Tablexdsl2PMLineCurrTable | not-accessible | current | The table xdsl2PMLineCurrTable contains current Performance Monitoring results for DSL lines. |
| 1.3.6.1.2.1.10.251.1.4.1.1.1 | Rowxdsl2PMLineCurrEntry | not-accessible | current | One index of this table is an interface index where the interface has an ifType of vdsl2(251). A second index of this table is the termination unit. |
| 1.3.6.1.2.1.10.251.1.4.1.1.1.1 | Columnxdsl2PMLCurrUnit | not-accessible | current | The termination unit. |
| 1.3.6.1.2.1.10.251.1.4.1.1.1.2 | Columnxdsl2PMLCurr15MValidIntervals | read-only | current | The number of 15-minute PM intervals for which data was collected. The value will typically be equal to the maximum number of 15-minute intervals the implement… |
| 1.3.6.1.2.1.10.251.1.4.1.1.1.3 | Columnxdsl2PMLCurr15MInvalidIntervals | read-only | current | The number of 15-minute PM intervals for which no data is available. The value will typically be zero except in cases where the data for some intervals are not… |
| 1.3.6.1.2.1.10.251.1.4.1.1.1.4 | Columnxdsl2PMLCurr15MTimeElapsed | read-only | current | Total elapsed seconds in this interval. |
| 1.3.6.1.2.1.10.251.1.4.1.1.1.5 | Columnxdsl2PMLCurr15MFecs | read-only | current | Count of seconds during this interval that there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibite… |
| 1.3.6.1.2.1.10.251.1.4.1.1.1.6 | Columnxdsl2PMLCurr15MEs | read-only | current | Count of seconds during this interval that there was: xTU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >=1 OR LPR >= 1. xTU-R: FEBE >= 1 fo… |
| 1.3.6.1.2.1.10.251.1.4.1.1.1.7 | Columnxdsl2PMLCurr15MSes | read-only | current | Count of seconds during this interval that there was: xTU-C: (CRC-8 anomalies in one or more of the received bearer channels) >= 18 OR LOS >= 1 OR SEF >= 1 OR … |
| 1.3.6.1.2.1.10.251.1.4.1.1.1.8 | Columnxdsl2PMLCurr15MLoss | read-only | current | Count of seconds during this interval that there was LOS (or LOS-FE for xTU-R). |
| 1.3.6.1.2.1.10.251.1.4.1.1.1.9 | Columnxdsl2PMLCurr15MUas | read-only | current | Count of seconds in Unavailability State during this interval. Unavailability begins at the onset of 10 contiguous severely errored seconds, and ends at the on… |
| 1.3.6.1.2.1.10.251.1.4.1.1.1.10 | Columnxdsl2PMLCurr1DayValidIntervals | read-only | current | The number of 24-hour PM intervals for which data was collected. The value will typically be equal to the maximum number of 24-hour intervals the implementatio… |
| 1.3.6.1.2.1.10.251.1.4.1.1.1.11 | Columnxdsl2PMLCurr1DayInvalidIntervals | read-only | current | The number of 24-hour PM intervals for which no data is available. The value will typically be zero except in cases where the data for some intervals are not a… |
| 1.3.6.1.2.1.10.251.1.4.1.1.1.12 | Columnxdsl2PMLCurr1DayTimeElapsed | read-only | current | Total elapsed seconds in this interval. |
| 1.3.6.1.2.1.10.251.1.4.1.1.1.13 | Columnxdsl2PMLCurr1DayFecs | read-only | current | Count of seconds during this interval that there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibite… |
| 1.3.6.1.2.1.10.251.1.4.1.1.1.14 | Columnxdsl2PMLCurr1DayEs | read-only | current | Count of seconds during this interval that there was: xTU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >= 1 OR LPR >= 1. xTU-R: FEBE >= 1 f… |
| 1.3.6.1.2.1.10.251.1.4.1.1.1.15 | Columnxdsl2PMLCurr1DaySes | read-only | current | Count of seconds during this interval that there was: xTU-C: (CRC-8 anomalies in one or more of the received bearer channels) >= 18 OR LOS >= 1 OR SEF >= 1 OR … |
| 1.3.6.1.2.1.10.251.1.4.1.1.1.16 | Columnxdsl2PMLCurr1DayLoss | read-only | current | Count of seconds during this interval that there was LOS (or LOS-FE for xTU-R). |
| 1.3.6.1.2.1.10.251.1.4.1.1.1.17 | Columnxdsl2PMLCurr1DayUas | read-only | current | Count of seconds in Unavailability State during this interval. Unavailability begins at the onset of 10 contiguous severely errored seconds, and ends at the on… |
| 1.3.6.1.2.1.10.251.1.4.1.2 | Tablexdsl2PMLineInitCurrTable | not-accessible | current | The table xdsl2PMLineInitCurrTable contains current initialization counters for DSL lines. |
| 1.3.6.1.2.1.10.251.1.4.1.2.1 | Rowxdsl2PMLineInitCurrEntry | not-accessible | current | The index of this table is an interface index where the interface has an ifType of vdsl2(251). |
| 1.3.6.1.2.1.10.251.1.4.1.2.1.1 | Columnxdsl2PMLInitCurr15MValidIntervals | read-only | current | The number of 15-minute PM intervals for which data was collected. The value will typically be equal to the maximum number of 15-minute intervals the implement… |
| 1.3.6.1.2.1.10.251.1.4.1.2.1.2 | Columnxdsl2PMLInitCurr15MInvalidIntervals | read-only | current | The number of 15-minute PM intervals for which no data is available. The value will typically be zero except in cases where the data for some intervals are not… |
| 1.3.6.1.2.1.10.251.1.4.1.2.1.3 | Columnxdsl2PMLInitCurr15MTimeElapsed | read-only | current | Total elapsed seconds in this interval. |
| 1.3.6.1.2.1.10.251.1.4.1.2.1.4 | Columnxdsl2PMLInitCurr15MFullInits | read-only | current | Count of full initializations attempted on the line (successful and failed) during this interval. |
| 1.3.6.1.2.1.10.251.1.4.1.2.1.5 | Columnxdsl2PMLInitCurr15MFailedFullInits | read-only | current | Count of failed full initializations on the line during this interval. |
| 1.3.6.1.2.1.10.251.1.4.1.2.1.6 | Columnxdsl2PMLInitCurr15MShortInits | read-only | current | Count of short initializations attempted on the line (successful and failed) during this interval. |
| 1.3.6.1.2.1.10.251.1.4.1.2.1.7 | Columnxdsl2PMLInitCurr15MFailedShortInits | read-only | current | Count of failed short initializations on the line during this interval. |
| 1.3.6.1.2.1.10.251.1.4.1.2.1.8 | Columnxdsl2PMLInitCurr1DayValidIntervals | read-only | current | The number of 24-hour PM intervals for which data was collected. The value will typically be equal to the maximum number of 24-hour intervals the implementatio… |
| 1.3.6.1.2.1.10.251.1.4.1.2.1.9 | Columnxdsl2PMLInitCurr1DayInvalidIntervals | read-only | current | The number of 24-hour PM intervals for which no data is available. The value will typically be zero except in cases where the data for some intervals are not a… |
| 1.3.6.1.2.1.10.251.1.4.1.2.1.10 | Columnxdsl2PMLInitCurr1DayTimeElapsed | read-only | current | Total elapsed seconds in this interval. |
| 1.3.6.1.2.1.10.251.1.4.1.2.1.11 | Columnxdsl2PMLInitCurr1DayFullInits | read-only | current | Count of full initializations attempted on the line (successful and failed) during this interval. |
| 1.3.6.1.2.1.10.251.1.4.1.2.1.12 | Columnxdsl2PMLInitCurr1DayFailedFullInits | read-only | current | Count of failed full initializations on the line during this interval. |
| 1.3.6.1.2.1.10.251.1.4.1.2.1.13 | Columnxdsl2PMLInitCurr1DayShortInits | read-only | current | Count of short initializations attempted on the line (successful and failed) during this interval. |
| 1.3.6.1.2.1.10.251.1.4.1.2.1.14 | Columnxdsl2PMLInitCurr1DayFailedShortInits | read-only | current | Count of failed short initializations on the line during this interval. |
| 1.3.6.1.2.1.10.251.1.4.1.3 | Tablexdsl2PMLineHist15MinTable | not-accessible | current | The table xdsl2PMLineHist15MinTable contains PM line history for 15-minute intervals of DSL line. |
| 1.3.6.1.2.1.10.251.1.4.1.3.1 | Rowxdsl2PMLineHist15MinEntry | not-accessible | current | One index of this table is an interface index where the interface has an ifType of vdsl2(251). A second index of this table is the transmission unit. The third… |
| 1.3.6.1.2.1.10.251.1.4.1.3.1.1 | Columnxdsl2PMLHist15MUnit | not-accessible | current | The termination unit. |
| 1.3.6.1.2.1.10.251.1.4.1.3.1.2 | Columnxdsl2PMLHist15MInterval | not-accessible | current | The interval number. |
| 1.3.6.1.2.1.10.251.1.4.1.3.1.3 | Columnxdsl2PMLHist15MMonitoredTime | read-only | current | Total seconds monitored in this interval. |
| 1.3.6.1.2.1.10.251.1.4.1.3.1.4 | Columnxdsl2PMLHist15MFecs | read-only | current | Count of seconds during this interval that there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibite… |
| 1.3.6.1.2.1.10.251.1.4.1.3.1.5 | Columnxdsl2PMLHist15MEs | read-only | current | Count of seconds during this interval that there was: xTU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >= 1 OR LPR >= 1. xTU-R: FEBE >= 1 f… |
| 1.3.6.1.2.1.10.251.1.4.1.3.1.6 | Columnxdsl2PMLHist15MSes | read-only | current | Count of seconds during this interval that there was: xTU-C: (CRC-8 anomalies in one or more of the received bearer channels) >= 18 OR LOS >= 1 OR SEF >= 1 OR … |
| 1.3.6.1.2.1.10.251.1.4.1.3.1.7 | Columnxdsl2PMLHist15MLoss | read-only | current | Count of seconds during this interval that there was LOS (or LOS-FE for xTU-R). |
| 1.3.6.1.2.1.10.251.1.4.1.3.1.8 | Columnxdsl2PMLHist15MUas | read-only | current | Count of seconds in Unavailability State during this interval. Unavailability begins at the onset of 10 contiguous severely errored seconds, and ends at the on… |
| 1.3.6.1.2.1.10.251.1.4.1.3.1.9 | Columnxdsl2PMLHist15MValidInterval | read-only | current | This variable indicates if the data for this interval is valid. |
| 1.3.6.1.2.1.10.251.1.4.1.4 | Tablexdsl2PMLineHist1DayTable | not-accessible | current | The table xdsl2PMLineHist1DayTable contains PM line history for 24-hour intervals of DSL line. |
| 1.3.6.1.2.1.10.251.1.4.1.4.1 | Rowxdsl2PMLineHist1DayEntry | not-accessible | current | One index of this table is an interface index where the interface has an ifType of vdsl2(251). A second index of this table is the transmission unit.The third … |
| 1.3.6.1.2.1.10.251.1.4.1.4.1.1 | Columnxdsl2PMLHist1DUnit | not-accessible | current | The termination unit. |
| 1.3.6.1.2.1.10.251.1.4.1.4.1.2 | Columnxdsl2PMLHist1DInterval | not-accessible | current | The interval number. |
| 1.3.6.1.2.1.10.251.1.4.1.4.1.3 | Columnxdsl2PMLHist1DMonitoredTime | read-only | current | Total seconds monitored in this interval. |
| 1.3.6.1.2.1.10.251.1.4.1.4.1.4 | Columnxdsl2PMLHist1DFecs | read-only | current | Count of seconds during this interval that there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibite… |
| 1.3.6.1.2.1.10.251.1.4.1.4.1.5 | Columnxdsl2PMLHist1DEs | read-only | current | Count of seconds during this interval that there was: xTU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >= 1 OR LPR >= 1. xTU-R: FEBE >= 1 f… |
| 1.3.6.1.2.1.10.251.1.4.1.4.1.6 | Columnxdsl2PMLHist1DSes | read-only | current | Count of seconds during this interval that there was: xTU-C: (CRC-8 anomalies in one or more of the received bearer channels) >= 18 OR LOS >= 1 OR SEF >= 1 OR … |
| 1.3.6.1.2.1.10.251.1.4.1.4.1.7 | Columnxdsl2PMLHist1DLoss | read-only | current | Count of seconds during this interval that there was LOS (or LOS-FE for xTU-R). |
| 1.3.6.1.2.1.10.251.1.4.1.4.1.8 | Columnxdsl2PMLHist1DUas | read-only | current | Count of seconds in Unavailability State during this interval. Unavailability begins at the onset of 10 contiguous severely errored seconds, and ends at the on… |
| 1.3.6.1.2.1.10.251.1.4.1.4.1.9 | Columnxdsl2PMLHist1DValidInterval | read-only | current | This variable indicates if the data for this interval is valid. |
| 1.3.6.1.2.1.10.251.1.4.1.5 | Tablexdsl2PMLineInitHist15MinTable | not-accessible | current | The table xdsl2PMLineInitHist15MinTable contains PM line initialization history for 15-minute intervals of DSL line. |
| 1.3.6.1.2.1.10.251.1.4.1.5.1 | Rowxdsl2PMLineInitHist15MinEntry | not-accessible | current | One index of this table is an interface index where the interface has an ifType of vdsl2(251). A second index is the interval number. |
| 1.3.6.1.2.1.10.251.1.4.1.5.1.1 | Columnxdsl2PMLInitHist15MInterval | not-accessible | current | The interval number. |
| 1.3.6.1.2.1.10.251.1.4.1.5.1.2 | Columnxdsl2PMLInitHist15MMonitoredTime | read-only | current | Total seconds monitored in this interval. |
| 1.3.6.1.2.1.10.251.1.4.1.5.1.3 | Columnxdsl2PMLInitHist15MFullInits | read-only | current | Count of full initializations attempted on the line (successful and failed) during this interval. |
| 1.3.6.1.2.1.10.251.1.4.1.5.1.4 | Columnxdsl2PMLInitHist15MFailedFullInits | read-only | current | Count of failed full initializations on the line during this interval. |
| 1.3.6.1.2.1.10.251.1.4.1.5.1.5 | Columnxdsl2PMLInitHist15MShortInits | read-only | current | Count of short initializations attempted on the line (successful and failed) during this interval. |
| 1.3.6.1.2.1.10.251.1.4.1.5.1.6 | Columnxdsl2PMLInitHist15MFailedShortInits | read-only | current | Count of failed short initializations on the line during this interval. |
| 1.3.6.1.2.1.10.251.1.4.1.5.1.7 | Columnxdsl2PMLInitHist15MValidInterval | read-only | current | This variable indicates if the data for this interval is valid. |
| 1.3.6.1.2.1.10.251.1.4.1.6 | Tablexdsl2PMLineInitHist1DayTable | not-accessible | current | The table xdsl2PMLineInitHist1DayTable contains PM line initialization history for 24-hour intervals for DSL lines. |
| 1.3.6.1.2.1.10.251.1.4.1.6.1 | Rowxdsl2PMLineInitHist1DayEntry | not-accessible | current | One index of this table is an interface index where the interface has an ifType of vdsl2(251). A second index is the interval number. |
| 1.3.6.1.2.1.10.251.1.4.1.6.1.1 | Columnxdsl2PMLInitHist1DInterval | not-accessible | current | The interval number. |
| 1.3.6.1.2.1.10.251.1.4.1.6.1.2 | Columnxdsl2PMLInitHist1DMonitoredTime | read-only | current | Total seconds monitored in this interval. |
| 1.3.6.1.2.1.10.251.1.4.1.6.1.3 | Columnxdsl2PMLInitHist1DFullInits | read-only | current | Count of full initializations attempted on the line (successful and failed) during this interval. |
| 1.3.6.1.2.1.10.251.1.4.1.6.1.4 | Columnxdsl2PMLInitHist1DFailedFullInits | read-only | current | Count of failed full initializations on the line during this interval. |
| 1.3.6.1.2.1.10.251.1.4.1.6.1.5 | Columnxdsl2PMLInitHist1DShortInits | read-only | current | Count of short initializations attempted on the line (successful and failed) during this interval. |
| 1.3.6.1.2.1.10.251.1.4.1.6.1.6 | Columnxdsl2PMLInitHist1DFailedShortInits | read-only | current | Count of failed short initializations on the line during this interval. |
| 1.3.6.1.2.1.10.251.1.4.1.6.1.7 | Columnxdsl2PMLInitHist1DValidInterval | read-only | current | This variable indicates if the data for this interval is valid. |
| 1.3.6.1.2.1.10.251.1.4.2 | Nodexdsl2PMChannel | |||
| 1.3.6.1.2.1.10.251.1.4.2.1 | Tablexdsl2PMChCurrTable | not-accessible | current | The table xdsl2PMChCurrTable contains current Performance Monitoring results for DSL channels. |
| 1.3.6.1.2.1.10.251.1.4.2.1.1 | Rowxdsl2PMChCurrEntry | not-accessible | current | One index of this table is an interface index where the interface has an ifType of a DSL channel. A second index of this table is the termination unit. |
| 1.3.6.1.2.1.10.251.1.4.2.1.1.1 | Columnxdsl2PMChCurrUnit | not-accessible | current | The termination unit. |
| 1.3.6.1.2.1.10.251.1.4.2.1.1.2 | Columnxdsl2PMChCurr15MValidIntervals | read-only | current | The number of 15-minute PM intervals for which data was collected. The value will typically be equal to the maximum number of 15-minute intervals the implement… |
| 1.3.6.1.2.1.10.251.1.4.2.1.1.3 | Columnxdsl2PMChCurr15MInvalidIntervals | read-only | current | The number of 15-minute PM intervals for which no data is available. The value will typically be zero except in cases where the data for some intervals are not… |
| 1.3.6.1.2.1.10.251.1.4.2.1.1.4 | Columnxdsl2PMChCurr15MTimeElapsed | read-only | current | Total elapsed seconds in this interval. |
| 1.3.6.1.2.1.10.251.1.4.2.1.1.5 | Columnxdsl2PMChCurr15MCodingViolations | read-only | current | Count of CRC-8 (FEBE for xTU-R) anomalies occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the CRC is applied ov… |
| 1.3.6.1.2.1.10.251.1.4.2.1.1.6 | Columnxdsl2PMChCurr15MCorrectedBlocks | read-only | current | Count of FEC (FFEC for xTU-R) anomalies (corrected code words) occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If … |
| 1.3.6.1.2.1.10.251.1.4.2.1.1.7 | Columnxdsl2PMChCurr1DayValidIntervals | read-only | current | The number of 24-hour PM intervals for which data was collected. The value will typically be equal to the maximum number of 24-hour intervals the implementatio… |
| 1.3.6.1.2.1.10.251.1.4.2.1.1.8 | Columnxdsl2PMChCurr1DayInvalidIntervals | read-only | current | The number of 24-hour PM intervals for which no data is available. The value will typically be zero except in cases where the data for some intervals are not a… |
| 1.3.6.1.2.1.10.251.1.4.2.1.1.9 | Columnxdsl2PMChCurr1DayTimeElapsed | read-only | current | Total elapsed seconds in this interval. |
| 1.3.6.1.2.1.10.251.1.4.2.1.1.10 | Columnxdsl2PMChCurr1DayCodingViolations | read-only | current | Count of CRC-8 (FEBE for xTU-R) anomalies occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the CRC is applied ov… |
| 1.3.6.1.2.1.10.251.1.4.2.1.1.11 | Columnxdsl2PMChCurr1DayCorrectedBlocks | read-only | current | Count of FEC (FFEC for xTU-R) anomalies (corrected code words) occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If … |
| 1.3.6.1.2.1.10.251.1.4.2.2 | Tablexdsl2PMChHist15MinTable | not-accessible | current | The table xdsl2PMChHist15MinTable contains Performance Monitoring (PM) history for 15-minute intervals for DSL channels PM. |
| 1.3.6.1.2.1.10.251.1.4.2.2.1 | Rowxdsl2PMChHist15MinEntry | not-accessible | current | One index of this table is an interface index where the interface has an ifType of a DSL channel. A second index of this table is the transmission unit. The th… |
| 1.3.6.1.2.1.10.251.1.4.2.2.1.1 | Columnxdsl2PMChHist15MUnit | not-accessible | current | The termination unit. |
| 1.3.6.1.2.1.10.251.1.4.2.2.1.2 | Columnxdsl2PMChHist15MInterval | not-accessible | current | The interval number. |
| 1.3.6.1.2.1.10.251.1.4.2.2.1.3 | Columnxdsl2PMChHist15MMonitoredTime | read-only | current | Total seconds monitored in this interval. |
| 1.3.6.1.2.1.10.251.1.4.2.2.1.4 | Columnxdsl2PMChHist15MCodingViolations | read-only | current | Count of CRC-8 (FEBE for xTU-R) anomalies occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the CRC is applied ov… |
| 1.3.6.1.2.1.10.251.1.4.2.2.1.5 | Columnxdsl2PMChHist15MCorrectedBlocks | read-only | current | Count of FEC (FFEC for xTU-R) anomalies (corrected code words) occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If … |
| 1.3.6.1.2.1.10.251.1.4.2.2.1.6 | Columnxdsl2PMChHist15MValidInterval | read-only | current | This variable indicates if the data for this interval is valid. |
| 1.3.6.1.2.1.10.251.1.4.2.3 | Tablexdsl2PMChHist1DTable | not-accessible | current | The table xdsl2PMChHist1DTable contains Performance Monitoring (PM) history for 1-day intervals for DSL channels PM. |
| 1.3.6.1.2.1.10.251.1.4.2.3.1 | Rowxdsl2PMChHist1DEntry | not-accessible | current | One index of this table is an interface index where the interface has an ifType of a DSL channel. A second index of this table is the transmission unit. The th… |
| 1.3.6.1.2.1.10.251.1.4.2.3.1.1 | Columnxdsl2PMChHist1DUnit | not-accessible | current | The termination unit. |
| 1.3.6.1.2.1.10.251.1.4.2.3.1.2 | Columnxdsl2PMChHist1DInterval | not-accessible | current | The interval number. |
| 1.3.6.1.2.1.10.251.1.4.2.3.1.3 | Columnxdsl2PMChHist1DMonitoredTime | read-only | current | Total seconds monitored in this interval. |
| 1.3.6.1.2.1.10.251.1.4.2.3.1.4 | Columnxdsl2PMChHist1DCodingViolations | read-only | current | Count of CRC-8 (FEBE for xTU-R) anomalies occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the CRC is applied ov… |
| 1.3.6.1.2.1.10.251.1.4.2.3.1.5 | Columnxdsl2PMChHist1DCorrectedBlocks | read-only | current | Count of FEC (FFEC for xTU-R) anomalies (corrected code words) occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If … |
| 1.3.6.1.2.1.10.251.1.4.2.3.1.6 | Columnxdsl2PMChHist1DValidInterval | read-only | current | This variable indicates if the data for this interval is valid. |
| 1.3.6.1.2.1.10.251.1.5 | Nodexdsl2Profile | |||
| 1.3.6.1.2.1.10.251.1.5.1 | Nodexdsl2ProfileLine | |||
| 1.3.6.1.2.1.10.251.1.5.1.1 | Tablexdsl2LineConfTemplateTable | not-accessible | current | The table xdsl2LineConfTemplateTable contains VDSL2/ADSL/ ADSL2 and ADSL2+ line configuration templates. Note that this table is also used to configure the num… |
| 1.3.6.1.2.1.10.251.1.5.1.1.1 | Rowxdsl2LineConfTemplateEntry | not-accessible | current | A default template with an index of 'DEFVAL' will always exist, and its parameters will be set to vendor-specific values, unless otherwise specified in this do… |
| 1.3.6.1.2.1.10.251.1.5.1.1.1.1 | Columnxdsl2LConfTempTemplateName | not-accessible | current | This object identifies a row in this table. |
| 1.3.6.1.2.1.10.251.1.5.1.1.1.2 | Columnxdsl2LConfTempLineProfile | read-create | current | The value of this object identifies the row in the VDSL2/ADSL/ADSL2 and ADSL2+ line configuration Profile Table (xdsl2LineConfProfTable) that applies for this … |
| 1.3.6.1.2.1.10.251.1.5.1.1.1.3 | Columnxdsl2LConfTempChan1ConfProfile | read-create | current | The value of this object identifies the row in the VDSL2/ ADSL/ADSL2 and ADSL2+ channel configuration Profile Table (xdsl2ChConfProfileTable) that applies to D… |
| 1.3.6.1.2.1.10.251.1.5.1.1.1.4 | Columnxdsl2LConfTempChan1RaRatioDs | read-create | current | Rate Adaptation Ratio. The ratio (in percent) that should be taken into account for the bearer channel #1 when performing rate adaptation on Downstream. The ra… |
| 1.3.6.1.2.1.10.251.1.5.1.1.1.5 | Columnxdsl2LConfTempChan1RaRatioUs | read-create | current | Rate Adaptation Ratio. The ratio (in percent) that should be taken into account for the bearer channel #1 when performing rate adaptation on Upstream. The rati… |
| 1.3.6.1.2.1.10.251.1.5.1.1.1.6 | Columnxdsl2LConfTempChan2ConfProfile | read-create | current | The value of this object identifies the row in the VDSL2/ ADSL/ADSL2 and ADSL2+ channel configuration Profile Table (xdsl2ChConfProfileTable) that applies to D… |
| 1.3.6.1.2.1.10.251.1.5.1.1.1.7 | Columnxdsl2LConfTempChan2RaRatioDs | read-create | current | Rate Adaptation Ratio. The ratio (in percent) that should be taken into account for the bearer channel #2 when performing rate adaptation on Downstream. The ra… |
| 1.3.6.1.2.1.10.251.1.5.1.1.1.8 | Columnxdsl2LConfTempChan2RaRatioUs | read-create | current | Rate Adaptation Ratio. The ratio (in percent) that should be taken into account for the bearer channel #2 when performing rate adaptation on Upstream. The rati… |
| 1.3.6.1.2.1.10.251.1.5.1.1.1.9 | Columnxdsl2LConfTempChan3ConfProfile | read-create | current | The value of this object identifies the row in the VDSL2/ ADSL/ADSL2 and ADSL2+ channel configuration Profile Table (xdsl2ChConfProfileTable) that applies to D… |
| 1.3.6.1.2.1.10.251.1.5.1.1.1.10 | Columnxdsl2LConfTempChan3RaRatioDs | read-create | current | Rate Adaptation Ratio. The ratio (in percent) that should be taken into account for the bearer channel #3 when performing rate adaptation on Downstream. The ra… |
| 1.3.6.1.2.1.10.251.1.5.1.1.1.11 | Columnxdsl2LConfTempChan3RaRatioUs | read-create | current | Rate Adaptation Ratio. The ratio (in percent) that should be taken into account for the bearer channel #3 when performing rate adaptation on Upstream. The rati… |
| 1.3.6.1.2.1.10.251.1.5.1.1.1.12 | Columnxdsl2LConfTempChan4ConfProfile | read-create | current | The value of this object identifies the row in the VDSL2/ ADSL/ADSL2 and ADSL2+ channel configuration Profile Table (xdsl2ChConfProfileTable) that applies to D… |
| 1.3.6.1.2.1.10.251.1.5.1.1.1.13 | Columnxdsl2LConfTempChan4RaRatioDs | read-create | current | Rate Adaptation Ratio. The ratio (in percent) that should be taken into account for the bearer channel #4 when performing rate adaptation on Downstream. The ra… |
| 1.3.6.1.2.1.10.251.1.5.1.1.1.14 | Columnxdsl2LConfTempChan4RaRatioUs | read-create | current | Rate Adaptation Ratio. The ratio (in percent) that should be taken into account for the bearer channel #4 when performing rate adaptation on Upstream. The rati… |
| 1.3.6.1.2.1.10.251.1.5.1.1.1.15 | Columnxdsl2LConfTempRowStatus | read-create | current | This object is used to create a new row or to modify or delete an existing row in this table. A template is activated by setting this object to 'active'. Befor… |
| 1.3.6.1.2.1.10.251.1.5.1.2 | Tablexdsl2LineConfProfTable | not-accessible | current | The table xdsl2LineConfProfTable contains VDSL2/ADSL/ ADSL2 and ADSL2+ line configuration profiles. Entries in this table MUST be maintained in a persistent ma… |
| 1.3.6.1.2.1.10.251.1.5.1.2.1 | Rowxdsl2LineConfProfEntry | not-accessible | current | A default profile with an index of 'DEFVAL' will always exist, and its parameters will be set to vendor-specific values, unless otherwise specified in this doc… |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.1 | Columnxdsl2LConfProfProfileName | not-accessible | current | This object identifies a row in this table. |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.2 | Columnxdsl2LConfProfScMaskDs | read-create | current | Subcarrier mask. A bitmap of 4096 bits that allows masking up to 4096 downstream subcarriers. If bit i (0 <= i < NSCds) is set to '1', the respective downstrea… |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.3 | Columnxdsl2LConfProfScMaskUs | read-create | current | Subcarrier mask. A bitmap of 4096 bits that allows masking up to 4096 upstream subcarriers. If bit i (0 <= i < NSCus) is set to '1', the respective upstream su… |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.4 | Columnxdsl2LConfProfVdsl2CarMask | read-create | current | VDSL2-specific subcarrier mask. This configuration parameter defines the restrictions, additional to the band plan, to determine the set of subcarriers allowed… |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.5 | Columnxdsl2LConfProfRfiBands | read-create | current | For ITU-T Recommendation G.992.5, this configuration parameter defines the subset of downstream PSD mask breakpoints, as specified in xdsl2LConfProfPsdMaskDs (… |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.6 | Columnxdsl2LConfProfRaModeDs | read-create | current | The mode of operation of a rate-adaptive xTU-C in the transmit direction. |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.7 | Columnxdsl2LConfProfRaModeUs | read-create | current | The mode of operation of a rate-adaptive xTU-R in the transmit direction. |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.8 | Columnxdsl2LConfProfRaUsNrmDs | read-create | current | The Downstream Up-Shift Noise Margin value, to be used when xdsl2LConfProfRaModeDs is set to 'dynamicRa'. If the downstream noise margin is above this value, a… |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.9 | Columnxdsl2LConfProfRaUsNrmUs | read-create | current | The Upstream Up-Shift Noise Margin value, to be used when xdsl2LConfProfRaModeUs is set to 'dynamicRa'. If the upstream noise margin is above this value, and s… |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.10 | Columnxdsl2LConfProfRaUsTimeDs | read-create | current | The Downstream Up-Shift Time Interval, to be used when xdsl2LConfProfRaModeDs is set to 'dynamicRa'. The interval of time that the downstream noise margin shou… |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.11 | Columnxdsl2LConfProfRaUsTimeUs | read-create | current | The Upstream Up-Shift Time Interval, to be used when xdsl2LConfProfRaModeUs is set to 'dynamicRa'. The interval of time the upstream noise margin should stay a… |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.12 | Columnxdsl2LConfProfRaDsNrmDs | read-create | current | The Downstream Down-Shift Noise Margin value, to be used when xdsl2LConfProfRaModeDs is set to 'dynamicRa'. If the downstream noise margin is below this value … |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.13 | Columnxdsl2LConfProfRaDsNrmUs | read-create | current | The Upstream Downshift Noise Margin value, to be used when xdsl2LConfProfRaModeUs is set to 'dynamicRa'. If the upstream noise margin is below this value and s… |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.14 | Columnxdsl2LConfProfRaDsTimeDs | read-create | current | The Downstream Downshift Time Interval, to be used when xdsl2LConfProfRaModeDs is set to 'dynamicRa'. The interval of time the downstream noise margin should s… |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.15 | Columnxdsl2LConfProfRaDsTimeUs | read-create | current | The Upstream Down-Shift Time Interval, to be used when xdsl2LConfProfRaModeUs is set to 'dynamicRa'. The interval of time the upstream noise margin should stay… |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.16 | Columnxdsl2LConfProfTargetSnrmDs | read-create | current | The minimum Noise Margin the xTU-R receiver shall achieve, relative to the BER requirement for each of the downstream bearer channels, to successfully complete… |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.17 | Columnxdsl2LConfProfTargetSnrmUs | read-create | current | The minimum Noise Margin the xTU-C receiver shall achieve, relative to the BER requirement for each of the upstream bearer channels, to successfully complete i… |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.18 | Columnxdsl2LConfProfMaxSnrmDs | read-create | current | The maximum Noise Margin the xTU-R receiver shall try to sustain. If the Noise Margin is above this level, the xTU-R shall request that the xTU-C reduce the xT… |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.19 | Columnxdsl2LConfProfMaxSnrmUs | read-create | current | The maximum Noise Margin the xTU-C receiver shall try to sustain. If the Noise Margin is above this level, the xTU-C shall request that the xTU-R reduce the xT… |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.20 | Columnxdsl2LConfProfMinSnrmDs | read-create | current | The minimum Noise Margin the xTU-R receiver shall tolerate. If the noise margin falls below this level, the xTU-R shall request that the xTU-C increase the xTU… |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.21 | Columnxdsl2LConfProfMinSnrmUs | read-create | current | The minimum Noise Margin the xTU-C receiver shall tolerate. If the noise margin falls below this level, the xTU-C shall request that the xTU-R increase the xTU… |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.22 | Columnxdsl2LConfProfMsgMinUs | read-create | current | Minimum Overhead Rate Upstream. Defines the minimum rate of the message-based overhead that shall be maintained by the xTU in upstream direction. Expressed in … |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.23 | Columnxdsl2LConfProfMsgMinDs | read-create | current | Minimum Overhead Rate Downstream. Defines the minimum rate of the message-based overhead that shall be maintained by the xTU in the downstream direction. Expre… |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.24 | Columnxdsl2LConfProfCeFlag | read-create | current | This parameter is a bit that enables the use of the optional cyclic extension values. |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.25 | Columnxdsl2LConfProfSnrModeDs | read-create | current | This parameter enables the transmitter-referred virtual noise in the downstream direction. |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.26 | Columnxdsl2LConfProfSnrModeUs | read-create | current | This parameter enables the transmitter-referred virtual noise in the upstream direction. |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.27 | Columnxdsl2LConfProfTxRefVnDs | read-create | current | This configuration parameter defines the downstream transmitter-referred virtual noise. The TXREFVNds shall be specified through a set of breakpoints. Each bre… |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.28 | Columnxdsl2LConfProfTxRefVnUs | read-create | current | This configuration parameter defines the upstream transmitter-referred virtual noise. The TXREFVNus shall be specified through a set of breakpoints. Each break… |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.29 | Columnxdsl2LConfProfXtuTransSysEna | read-create | current | xTU Transmission System Enabling (XTSE). A list of the different coding types enabled in this profile. It is coded in a bitmap representation with 1 or more bi… |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.30 | Columnxdsl2LConfProfPmMode | read-create | current | Power management state Enabling (PMMode). Defines the power states the xTU-C or xTU-R may autonomously transition to on this line. This is a set of bits, where… |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.31 | Columnxdsl2LConfProfL0Time | read-create | current | The minimum time (in seconds) between an Exit from the L2 state and the next Entry into the L2 state. It ranges from 0 to 255 seconds. |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.32 | Columnxdsl2LConfProfL2Time | read-create | current | The minimum time (in seconds) between an Entry into the L2 state and the first Power Trim in the L2 state and between two consecutive Power Trims in the L2 sta… |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.33 | Columnxdsl2LConfProfL2Atpr | read-create | current | The maximum aggregate transmit power reduction (in dB) that can be performed at transition of L0 to L2 state or through a single Power Trim in the L2 state. It… |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.34 | Columnxdsl2LConfProfL2Atprt | read-create | current | The total maximum aggregate transmit power reduction (in dB) that can be performed in an L2 state. This is the sum of all reductions of L2 Requests (i.e., at t… |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.35 | Columnxdsl2LConfProfProfiles | read-create | current | The configuration parameter contains the G.993.2 profiles to be allowed by the near-end xTU on this line. It is coded in a bitmap representation (0 if not allo… |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.36 | Columnxdsl2LConfProfDpboEPsd | read-create | current | This configuration parameter defines the PSD mask that is assumed to be permitted at the exchange. This parameter shall use the same format as xdsl2LConfProfPs… |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.37 | Columnxdsl2LConfProfDpboEsEL | read-create | current | This configuration parameter defines the assumed electrical length of cables (E-side cables) connecting exchange-based DSL services to a remote flexibility poi… |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.38 | Columnxdsl2LConfProfDpboEsCableModelA | read-create | current | The E-side Cable Model parameter A (DPBOESCMA) of the cable model (DPBOESCM) for cables connecting exchange-based DSL services to a remote flexibility point (c… |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.39 | Columnxdsl2LConfProfDpboEsCableModelB | read-create | current | The E-side Cable Model parameter B (DPBOESCMB) of the cable model (DPBOESCM) for cables connecting exchange-based DSL services to a remote flexibility point (c… |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.40 | Columnxdsl2LConfProfDpboEsCableModelC | read-create | current | The E-side Cable Model parameter C (DPBOESCMC) of the cable model (DPBOESCM) for cables connecting exchange-based DSL services to a remote flexibility point (c… |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.41 | Columnxdsl2LConfProfDpboMus | read-create | current | This configuration parameter defines the assumed Minimum Usable receive PSD mask (in dBm/Hz) for exchange-based services, used to modify parameter xdsl2LConfPr… |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.42 | Columnxdsl2LConfProfDpboFMin | read-create | current | This configuration parameter defines the minimum frequency from which the DPBO shall be applied. It ranges from 0 kHz (coded as 0) to 8832 kHz (coded as 2048) … |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.43 | Columnxdsl2LConfProfDpboFMax | read-create | current | This configuration parameter defines the maximum frequency at which DPBO may be applied. It ranges from 138 kHz (coded as 32) to 29997.75 kHz (coded as 6956) i… |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.44 | Columnxdsl2LConfProfUpboKL | read-create | current | This configuration parameter defines the electrical length expressed in dB at 1 MHz, kl0, configured by the CO-MIB. The value ranges from 0 (coded as 0) to 128… |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.45 | Columnxdsl2LConfProfUpboKLF | read-create | current | Defines the upstream power backoff force mode. |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.46 | Columnxdsl2LConfProfUs0Mask | read-create | current | The configuration parameter contains the US0 PSD masks to be allowed by the near-end xTU on the line. This parameter is only defined for G.993.2 Annex A. It is… |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.47 | Columnxdsl2LConfProfForceInp | read-create | current | This parameter, when set to 'true' indicates that the framer settings of the bearer shall be selected such that the impulse noise protection computed according… |
| 1.3.6.1.2.1.10.251.1.5.1.2.1.48 | Columnxdsl2LConfProfRowStatus | read-create | current | This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. Before… |
| 1.3.6.1.2.1.10.251.1.5.1.3 | Tablexdsl2LineConfProfModeSpecTable | not-accessible | current | The table xdsl2LineConfProfModeSpecTable extends the DSL line configuration profile by xDSL Mode-Specific parameters. A row in this table that has an index of … |
| 1.3.6.1.2.1.10.251.1.5.1.3.1 | Rowxdsl2LineConfProfModeSpecEntry | not-accessible | current | The table xdsl2LineConfProfModeSpecTable extends the DSL line configuration profile by DSL Mode-Specific parameters. |
| 1.3.6.1.2.1.10.251.1.5.1.3.1.1 | Columnxdsl2LConfProfXdslMode | not-accessible | current | The DSL Mode is a way of categorizing the various xDSL transmission modes into groups, each group (xDSL Mode) shares the same PSD configuration. There should b… |
| 1.3.6.1.2.1.10.251.1.5.1.3.1.2 | Columnxdsl2LConfProfMaxNomPsdDs | read-create | current | The maximum nominal transmit PSD in the downstream direction during initialization and Showtime. It ranges from -600 to -300 units of 0.1 dBm/Hz (physical valu… |
| 1.3.6.1.2.1.10.251.1.5.1.3.1.3 | Columnxdsl2LConfProfMaxNomPsdUs | read-create | current | The maximum nominal transmit PSD in the upstream direction during initialization and Showtime. It ranges from -600 to -300 units of 0.1 dBm/Hz (physical values… |
| 1.3.6.1.2.1.10.251.1.5.1.3.1.4 | Columnxdsl2LConfProfMaxNomAtpDs | read-create | current | The maximum nominal aggregate to transmit power in the downstream direction during initialization and Showtime. It ranges from 0 to 255 units of 0.1 dBm (physi… |
| 1.3.6.1.2.1.10.251.1.5.1.3.1.5 | Columnxdsl2LConfProfMaxNomAtpUs | read-create | current | The maximum nominal aggregate transmit power in the upstream direction during initialization and Showtime. It ranges from 0 to 255 units of 0.1 dBm (physical v… |
| 1.3.6.1.2.1.10.251.1.5.1.3.1.6 | Columnxdsl2LConfProfMaxAggRxPwrUs | read-create | current | The maximum upstream aggregate receive power over the relevant set of subcarriers. The xTU-C should verify that the upstream power cutback is such that this ma… |
| 1.3.6.1.2.1.10.251.1.5.1.3.1.7 | Columnxdsl2LConfProfPsdMaskDs | read-create | current | The downstream PSD mask applicable at the U-C2 reference point. This parameter is used only for G.992.5 and it may impose PSD restrictions (breakpoints) in add… |
| 1.3.6.1.2.1.10.251.1.5.1.3.1.8 | Columnxdsl2LConfProfPsdMaskUs | read-create | current | The upstream PSD mask applicable at the U-R2 reference point. This parameter is used only for G.992.5, and it may impose PSD restrictions (breakpoints) in addi… |
| 1.3.6.1.2.1.10.251.1.5.1.3.1.9 | Columnxdsl2LConfProfPsdMaskSelectUs | read-create | current | The selected upstream PSD mask. This parameter is used only for Annexes J and M of G.992.3 and G.992.5, and the same selection is used for all relevant enabled… |
| 1.3.6.1.2.1.10.251.1.5.1.3.1.10 | Columnxdsl2LConfProfClassMask | read-create | current | In order to reduce the number of configuration possibilities, the limit Power Spectral Density masks (see LIMITMASK) are grouped in PSD mask classes. Each clas… |
| 1.3.6.1.2.1.10.251.1.5.1.3.1.11 | Columnxdsl2LConfProfLimitMask | read-create | current | This configuration parameter contains the G.993.2 limit PSD masks of the selected PSD mask class, enabled by the near-end xTU on this line for each class of pr… |
| 1.3.6.1.2.1.10.251.1.5.1.3.1.12 | Columnxdsl2LConfProfUs0Disable | read-create | current | This configuration parameter indicates if the use of the US0 is disabled for each limit PSD mask enabled in the xdsl2LConfProfLimitMask parameter. This paramet… |
| 1.3.6.1.2.1.10.251.1.5.1.3.1.13 | Columnxdsl2LConfProfModeSpecRowStatus | read-create | current | This object is used to create a new row or to modify or delete an existing row in this table. This row is activated by setting this object to 'active'. A 'mand… |
| 1.3.6.1.2.1.10.251.1.5.1.4 | Tablexdsl2LineConfProfModeSpecBandUsTable | not-accessible | current | The table xdsl2LineConfProfModeSpecBandUsTable extends xdsl2LineConfProfModeSpecTable with upstream-band-specific parameters for VDSL2, such as upstream power … |
| 1.3.6.1.2.1.10.251.1.5.1.4.1 | Rowxdsl2LineConfProfModeSpecBandUsEntry | not-accessible | current | The table xdsl2LineConfProfModeSpecBandUsTable extends xdsl2LineConfProfModeSpecTable with upstream-band-specific parameters for VDSL2, such as upstream power … |
| 1.3.6.1.2.1.10.251.1.5.1.4.1.1 | Columnxdsl2LConfProfXdslBandUs | not-accessible | current | Each value identifies a specific band in the upstream transmission direction (excluding the US0 band). |
| 1.3.6.1.2.1.10.251.1.5.1.4.1.2 | Columnxdsl2LConfProfUpboPsdA | read-create | current | This configuration parameter defines the 'a' reference parameter of the UPBO reference PSD used to compute the upstream power back-off for the upstream band. A… |
| 1.3.6.1.2.1.10.251.1.5.1.4.1.3 | Columnxdsl2LConfProfUpboPsdB | read-create | current | This configuration parameter defines the 'b' reference parameter of the UPBO reference PSD used to compute the upstream power back-off for the upstream band. A… |
| 1.3.6.1.2.1.10.251.1.5.1.4.1.4 | Columnxdsl2LConfProfModeSpecBandUsRowStatus | read-create | current | This object is used to create a new row or to modify or delete an existing row in this table. This row is activated by setting this object to 'active'. A 'mand… |
| 1.3.6.1.2.1.10.251.1.5.2 | Nodexdsl2ProfileChannel | |||
| 1.3.6.1.2.1.10.251.1.5.2.1 | Tablexdsl2ChConfProfileTable | not-accessible | current | The table xdsl2ChConfProfileTable contains DSL channel profile configuration. Entries in this table MUST be maintained in a persistent manner. |
| 1.3.6.1.2.1.10.251.1.5.2.1.1 | Rowxdsl2ChConfProfileEntry | not-accessible | current | A default profile with an index of 'DEFVAL' will always exist, and its parameters will be set to vendor-specific values, unless otherwise specified in this doc… |
| 1.3.6.1.2.1.10.251.1.5.2.1.1.1 | Columnxdsl2ChConfProfProfileName | not-accessible | current | This object identifies a row in this table. |
| 1.3.6.1.2.1.10.251.1.5.2.1.1.2 | Columnxdsl2ChConfProfMinDataRateDs | read-create | current | Minimum Data Rate on Downstream direction. The minimum net data rate for the bearer channel, coded in bit/s. |
| 1.3.6.1.2.1.10.251.1.5.2.1.1.3 | Columnxdsl2ChConfProfMinDataRateUs | read-create | current | Minimum Data Rate on Upstream direction. The minimum net data rate for the bearer channel, coded in bit/s. |
| 1.3.6.1.2.1.10.251.1.5.2.1.1.4 | Columnxdsl2ChConfProfMinResDataRateDs | read-create | current | Minimum Reserved Data Rate on Downstream direction. The minimum reserved net data rate for the bearer channel, coded in bit/s. This parameter is used only if t… |
| 1.3.6.1.2.1.10.251.1.5.2.1.1.5 | Columnxdsl2ChConfProfMinResDataRateUs | read-create | current | Minimum Reserved Data Rate on Upstream direction. The minimum reserved net data rate for the bearer channel, coded in bit/s. This parameter is used only if the… |
| 1.3.6.1.2.1.10.251.1.5.2.1.1.6 | Columnxdsl2ChConfProfMaxDataRateDs | read-create | current | Maximum Data Rate on Downstream direction. The maximum net data rate for the bearer channel, coded in bit/s. |
| 1.3.6.1.2.1.10.251.1.5.2.1.1.7 | Columnxdsl2ChConfProfMaxDataRateUs | read-create | current | Maximum Data Rate on Upstream direction. The maximum net data rate for the bearer channel, coded in bit/s. |
| 1.3.6.1.2.1.10.251.1.5.2.1.1.8 | Columnxdsl2ChConfProfMinDataRateLowPwrDs | read-create | current | This parameter specifies the minimum net data rate for the bearer channel as desired by the operator of the system during the low power state (L1/L2). The powe… |
| 1.3.6.1.2.1.10.251.1.5.2.1.1.9 | Columnxdsl2ChConfProfMinDataRateLowPwrUs | read-create | current | This parameter specifies the minimum net data rate for the bearer channel as desired by the operator of the system during the low power state (L1/L2). The powe… |
| 1.3.6.1.2.1.10.251.1.5.2.1.1.10 | Columnxdsl2ChConfProfMaxDelayDs | read-create | current | Maximum Interleave Delay on Downstream direction. The maximum one-way interleaving delay introduced by the PMS-TC on Downstream direction. The xTUs shall choos… |
| 1.3.6.1.2.1.10.251.1.5.2.1.1.11 | Columnxdsl2ChConfProfMaxDelayUs | read-create | current | Maximum Interleave Delay on Upstream direction. The maximum one-way interleaving delay introduced by the PMS-TC on Upstream direction. The xTUs shall choose th… |
| 1.3.6.1.2.1.10.251.1.5.2.1.1.12 | Columnxdsl2ChConfProfMinProtectionDs | read-create | current | This parameter specifies the minimum impulse noise protection for the bearer channel if it is transported over DMT symbols with a subcarrier spacing of 4.3125 … |
| 1.3.6.1.2.1.10.251.1.5.2.1.1.13 | Columnxdsl2ChConfProfMinProtectionUs | read-create | current | This parameter specifies the minimum impulse noise protection for the bearer channel if it is transported over DMT symbols with a subcarrier spacing of 4.3125 … |
| 1.3.6.1.2.1.10.251.1.5.2.1.1.14 | Columnxdsl2ChConfProfMinProtection8Ds | read-create | current | This parameter specifies the minimum impulse noise protection for the bearer channel if it is transported over DMT symbols with a subcarrier spacing of 8.625 k… |
| 1.3.6.1.2.1.10.251.1.5.2.1.1.15 | Columnxdsl2ChConfProfMinProtection8Us | read-create | current | This parameter specifies the minimum impulse noise protection for the bearer channel if it is transported over DMT symbols with a subcarrier spacing of 8.625 k… |
| 1.3.6.1.2.1.10.251.1.5.2.1.1.16 | Columnxdsl2ChConfProfMaxBerDs | read-create | current | Maximum Bit Error Ratio on Downstream direction. The maximum bit error ratio for the bearer channel. |
| 1.3.6.1.2.1.10.251.1.5.2.1.1.17 | Columnxdsl2ChConfProfMaxBerUs | read-create | current | Maximum Bit Error Ratio on Upstream direction. The maximum bit error ratio for the bearer channel. |
| 1.3.6.1.2.1.10.251.1.5.2.1.1.18 | Columnxdsl2ChConfProfUsDataRateDs | read-create | current | Data Rate Threshold Upshift for Downstream direction. An 'Up-Shift rate change' event is triggered when the actual downstream data rate exceeds, by more than t… |
| 1.3.6.1.2.1.10.251.1.5.2.1.1.19 | Columnxdsl2ChConfProfDsDataRateDs | read-create | current | Data Rate Threshold Downshift for Downstream direction. A 'Down-Shift rate change' event is triggered when the actual downstream data rate is below the data ra… |
| 1.3.6.1.2.1.10.251.1.5.2.1.1.20 | Columnxdsl2ChConfProfUsDataRateUs | read-create | current | Data Rate Threshold Upshift for Upstream direction. An 'Up-Shift rate change' event is triggered when the actual upstream data rate exceeds, by more than the t… |
| 1.3.6.1.2.1.10.251.1.5.2.1.1.21 | Columnxdsl2ChConfProfDsDataRateUs | read-create | current | Data Rate Threshold Downshift for Upstream direction. A 'Down-Shift rate change' event is triggered when the actual upstream data rate is below the data rate a… |
| 1.3.6.1.2.1.10.251.1.5.2.1.1.22 | Columnxdsl2ChConfProfImaEnabled | read-create | current | IMA Mode Enable. The parameter enables the IMA operation mode in the ATM Data Path. Relevant only if the channel is of ATM Data Path. When in 'enable' state, t… |
| 1.3.6.1.2.1.10.251.1.5.2.1.1.23 | Columnxdsl2ChConfProfMaxDelayVar | read-create | current | Maximum delay variation (DVMAX). This optional VDSL2-specific parameter specifies the maximum value for the delay variation allowed in an OLR procedure. It is … |
| 1.3.6.1.2.1.10.251.1.5.2.1.1.24 | Columnxdsl2ChConfProfInitPolicy | read-create | current | Channel Initialization Policy Selection (CIPOLICY). This optional parameter indicates which policy shall be applied to determine the transceiver configuration … |
| 1.3.6.1.2.1.10.251.1.5.2.1.1.25 | Columnxdsl2ChConfProfRowStatus | read-create | current | This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. Before… |
| 1.3.6.1.2.1.10.251.1.5.3 | Nodexdsl2ProfileAlarmConf | |||
| 1.3.6.1.2.1.10.251.1.5.3.1 | Tablexdsl2LineAlarmConfTemplateTable | not-accessible | current | The table xdsl2LineAlarConfTemplateTable contains DSL line alarm configuration templates. Entries in this table MUST be maintained in a persistent manner. |
| 1.3.6.1.2.1.10.251.1.5.3.1.1 | Rowxdsl2LineAlarmConfTemplateEntry | not-accessible | current | A default template with an index of 'DEFVAL' will always exist, and its parameters will be set to vendor-specific values, unless otherwise specified in this do… |
| 1.3.6.1.2.1.10.251.1.5.3.1.1.1 | Columnxdsl2LAlarmConfTempTemplateName | not-accessible | current | This object identifies a row in this table. |
| 1.3.6.1.2.1.10.251.1.5.3.1.1.2 | Columnxdsl2LAlarmConfTempLineProfile | read-create | current | The value of this object identifies the row in the DSL Line Thresholds Configuration Profile Table (xdsl2LineAlarmConfProfileTable) that applies to this line. |
| 1.3.6.1.2.1.10.251.1.5.3.1.1.3 | Columnxdsl2LAlarmConfTempChan1ConfProfile | read-create | current | The value of this object identifies the row in the DSL Channel Thresholds Configuration Profile Table (xdsl2ChAlarmConfProfileTable) that applies for DSL beare… |
| 1.3.6.1.2.1.10.251.1.5.3.1.1.4 | Columnxdsl2LAlarmConfTempChan2ConfProfile | read-create | current | The value of this object identifies the row in the DSL Channel Thresholds Configuration Profile Table (xdsl2ChAlarmConfProfileTable) that applies for DSL beare… |
| 1.3.6.1.2.1.10.251.1.5.3.1.1.5 | Columnxdsl2LAlarmConfTempChan3ConfProfile | read-create | current | The value of this object identifies the row in the DSL Channel Thresholds Configuration Profile Table (xdsl2ChAlarmConfProfileTable) that applies for DSL beare… |
| 1.3.6.1.2.1.10.251.1.5.3.1.1.6 | Columnxdsl2LAlarmConfTempChan4ConfProfile | read-create | current | The value of this object identifies the row in the DSL Channel Thresholds Configuration Profile Table (xdsl2ChAlarmConfProfileTable) that applies for DSL beare… |
| 1.3.6.1.2.1.10.251.1.5.3.1.1.7 | Columnxdsl2LAlarmConfTempRowStatus | read-create | current | This object is used to create a new row or to modify or delete an existing row in this table. A template is activated by setting this object to 'active'. Befor… |
| 1.3.6.1.2.1.10.251.1.5.3.2 | Tablexdsl2LineAlarmConfProfileTable | not-accessible | current | The table xdsl2LineAlarmConfProfileTable contains DSL line performance threshold values. If a performance counter exceeds the threshold value specified in this… |
| 1.3.6.1.2.1.10.251.1.5.3.2.1 | Rowxdsl2LineAlarmConfProfileEntry | not-accessible | current | A default profile with an index of 'DEFVAL' will always exist, and its parameters will be set to vendor-specific values, unless otherwise specified in this doc… |
| 1.3.6.1.2.1.10.251.1.5.3.2.1.1 | Columnxdsl2LineAlarmConfProfileName | not-accessible | current | This object identifies a row in this table. |
| 1.3.6.1.2.1.10.251.1.5.3.2.1.2 | Columnxdsl2LineAlarmConfProfileXtucThresh15MinFecs | read-create | current | A threshold for the xdsl2PMLCurr15MFecs counter, when xdsl2PMLCurrUnit is xtuc {1}. The value 0 means that no threshold is specified for the associated counter. |
| 1.3.6.1.2.1.10.251.1.5.3.2.1.3 | Columnxdsl2LineAlarmConfProfileXtucThresh15MinEs | read-create | current | A threshold for the xdsl2PMLCurr15MEs counter, when xdsl2PMLCurrUnit is xtuc {1}. The value 0 means that no threshold is specified for the associated counter. |
| 1.3.6.1.2.1.10.251.1.5.3.2.1.4 | Columnxdsl2LineAlarmConfProfileXtucThresh15MinSes | read-create | current | A threshold for the xdsl2PMLCurr15MSes counter, when xdsl2PMLCurrUnit is xtuc {1}. The value 0 means that no threshold is specified for the associated counter. |
| 1.3.6.1.2.1.10.251.1.5.3.2.1.5 | Columnxdsl2LineAlarmConfProfileXtucThresh15MinLoss | read-create | current | A threshold for the xdsl2PMLCurr15MLoss counter, when xdsl2PMLCurrUnit is xtuc {1}. The value 0 means that no threshold is specified for the associated counter. |
| 1.3.6.1.2.1.10.251.1.5.3.2.1.6 | Columnxdsl2LineAlarmConfProfileXtucThresh15MinUas | read-create | current | A threshold for the xdsl2PMLCurr15MUas counter, when xdsl2PMLCurrUnit is xtuc {1}. The value 0 means that no threshold is specified for the associated counter. |
| 1.3.6.1.2.1.10.251.1.5.3.2.1.7 | Columnxdsl2LineAlarmConfProfileXturThresh15MinFecs | read-create | current | A threshold for the xdsl2PMLCurr15MFecs counter, when xdsl2PMLCurrUnit is xtur {2}. The value 0 means that no threshold is specified for the associated counter. |
| 1.3.6.1.2.1.10.251.1.5.3.2.1.8 | Columnxdsl2LineAlarmConfProfileXturThresh15MinEs | read-create | current | A threshold for the xdsl2PMLCurr15MEs counter, when xdsl2PMLCurrUnit is xtur {2}. The value 0 means that no threshold is specified for the associated counter. |
| 1.3.6.1.2.1.10.251.1.5.3.2.1.9 | Columnxdsl2LineAlarmConfProfileXturThresh15MinSes | read-create | current | A threshold for the xdsl2PMLCurr15MSes counter, when xdsl2PMLCurrUnit is xtur {2}. The value 0 means that no threshold is specified for the associated counter. |
| 1.3.6.1.2.1.10.251.1.5.3.2.1.10 | Columnxdsl2LineAlarmConfProfileXturThresh15MinLoss | read-create | current | A threshold for the xdsl2PMLCurr15MLoss counter, when xdsl2PMLCurrUnit is xtur {2}. The value 0 means that no threshold is specified for the associated counter. |
| 1.3.6.1.2.1.10.251.1.5.3.2.1.11 | Columnxdsl2LineAlarmConfProfileXturThresh15MinUas | read-create | current | A threshold for the xdsl2PMLCurr15MUas counter, when xdsl2PMLCurrUnit is xtur {2}. The value 0 means that no threshold is specified for the associated counter. |
| 1.3.6.1.2.1.10.251.1.5.3.2.1.12 | Columnxdsl2LineAlarmConfProfileThresh15MinFailedFullInt | read-create | current | A threshold for the xdsl2PMLInitCurr15MfailedFullInits counter. The value 0 means that no threshold is specified for the associated counter. |
| 1.3.6.1.2.1.10.251.1.5.3.2.1.13 | Columnxdsl2LineAlarmConfProfileThresh15MinFailedShrtInt | read-create | current | A threshold for the xdsl2PMLInitCurr15MFailedShortInits counter. The value 0 means that no threshold is specified for the associated counter. |
| 1.3.6.1.2.1.10.251.1.5.3.2.1.14 | Columnxdsl2LineAlarmConfProfileRowStatus | read-create | current | This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. Before… |
| 1.3.6.1.2.1.10.251.1.5.3.3 | Tablexdsl2ChAlarmConfProfileTable | not-accessible | current | The table xdsl2ChAlarmConfProfileTable contains DSL channel performance threshold values. If a performance counter exceeds the threshold value specified in thi… |
| 1.3.6.1.2.1.10.251.1.5.3.3.1 | Rowxdsl2ChAlarmConfProfileEntry | not-accessible | current | A default profile with an index of 'DEFVAL' will always exist, and its parameters will be set to vendor-specific values, unless otherwise specified in this doc… |
| 1.3.6.1.2.1.10.251.1.5.3.3.1.1 | Columnxdsl2ChAlarmConfProfileName | not-accessible | current | This object identifies a row in this table. |
| 1.3.6.1.2.1.10.251.1.5.3.3.1.2 | Columnxdsl2ChAlarmConfProfileXtucThresh15MinCodingViolations | read-create | current | A threshold for the xdsl2PMChCurr15MCodingViolations counter, when xdsl2PMChCurrUnit is xtuc {1}. The value 0 means that no threshold is specified for the asso… |
| 1.3.6.1.2.1.10.251.1.5.3.3.1.3 | Columnxdsl2ChAlarmConfProfileXtucThresh15MinCorrected | read-create | current | A threshold for the xdsl2PMChCurr15MCorrectedBlocks counter, when xdsl2PMChCurrUnit is xtuc {1}. The value 0 means that no threshold is specified for the assoc… |
| 1.3.6.1.2.1.10.251.1.5.3.3.1.4 | Columnxdsl2ChAlarmConfProfileXturThresh15MinCodingViolations | read-create | current | A threshold for the xdsl2PMChCurr15MCodingViolations counter, when xdsl2PMChCurrUnit is xtur {2}. The value 0 means that no threshold is specified for the asso… |
| 1.3.6.1.2.1.10.251.1.5.3.3.1.5 | Columnxdsl2ChAlarmConfProfileXturThresh15MinCorrected | read-create | current | A threshold for the xdsl2PMChCurr15MCorrectedBlocks counter, when xdsl2PMChCurrUnit is xtur {2}. The value 0 means that no threshold is specified for the assoc… |
| 1.3.6.1.2.1.10.251.1.5.3.3.1.6 | Columnxdsl2ChAlarmConfProfileRowStatus | read-create | current | This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. Before… |
| 1.3.6.1.2.1.10.251.1.6 | Nodexdsl2Scalar | |||
| 1.3.6.1.2.1.10.251.1.6.1 | Nodexdsl2ScalarSC | |||
| 1.3.6.1.2.1.10.251.1.6.1.1 | Scalarxdsl2ScalarSCMaxInterfaces | read-only | current | This value determines the maximum number of interfaces supported by xdsl2SCStatusTable, xdsl2SCStatusBandTable, and xdsl2SCStatusSegmentTable. |
| 1.3.6.1.2.1.10.251.1.6.1.2 | Scalarxdsl2ScalarSCAvailInterfaces | read-only | current | This value determines the currently available number of interfaces listed in xdsl2SCStatusTable, xdsl2SCStatusBandTable, and xdsl2SCStatusSegmentTable. |
| 1.3.6.1.2.1.10.251.2 | Nodexdsl2Conformance | |||
| 1.3.6.1.2.1.10.251.2.1 | Nodexdsl2Groups | |||
| 1.3.6.1.2.1.10.251.2.1.1 | Groupxdsl2LineGroup | current | The group of configuration, status, and commands objects on the line level. | |
| 1.3.6.1.2.1.10.251.2.1.2 | Groupxdsl2LineFallbackGroup | current | The group of configuration, status, and commands objects on the line level that are associated with the fallback feature. | |
| 1.3.6.1.2.1.10.251.2.1.3 | Groupxdsl2LineBpscGroup | current | The group of configuration, status, and commands objects on the line level that are associated with requesting a bits-per-subcarrier measurement. | |
| 1.3.6.1.2.1.10.251.2.1.4 | Groupxdsl2LineSegmentGroup | current | The group of status and commands objects on the line level that are used to hold the results of the bits-per-subcarrier measurement. | |
| 1.3.6.1.2.1.10.251.2.1.5 | Groupxdsl2ChannelStatusGroup | current | The group of status objects on the channel level. | |
| 1.3.6.1.2.1.10.251.2.1.6 | Groupxdsl2ChannelStatusAtmGroup | current | The group of status objects on the data path level when it is ATM. | |
| 1.3.6.1.2.1.10.251.2.1.7 | Groupxdsl2ChannelStatusPtmGroup | current | The group of status objects on the data path level when it is PTM. | |
| 1.3.6.1.2.1.10.251.2.1.8 | Groupxdsl2SCStatusGroup | current | The group of status objects on the subcarrier level. They are updated as a result of a DELT process. | |
| 1.3.6.1.2.1.10.251.2.1.9 | Groupxdsl2LineInventoryGroup | current | The group of inventory objects per xTU. | |
| 1.3.6.1.2.1.10.251.2.1.10 | Groupxdsl2LineConfTemplateGroup | current | The group of objects in a line configuration template. | |
| 1.3.6.1.2.1.10.251.2.1.11 | Groupxdsl2LineConfProfGroup | current | The group of objects in a line configuration profile. | |
| 1.3.6.1.2.1.10.251.2.1.12 | Groupxdsl2LineConfProfRaGroup | current | The group of objects required for controlling the rate-adaptive behavior of the line. | |
| 1.3.6.1.2.1.10.251.2.1.13 | Groupxdsl2LineConfProfMsgMinGroup | current | The group of objects required for controlling the rate reserved for Overhead traffic. | |
| 1.3.6.1.2.1.10.251.2.1.14 | Groupxdsl2LineConfProfModeSpecGroup | current | The group of objects in a line configuration profile that have an instance for each operation mode allowed. | |
| 1.3.6.1.2.1.10.251.2.1.15 | Groupxdsl2LineConfProfModeSpecBandUsGroup | current | The group of objects in a line configuration profile that have several per-upstream-band instances for each operation mode allowed. | |
| 1.3.6.1.2.1.10.251.2.1.16 | Groupxdsl2ChConfProfileGroup | current | The group of objects in a channel configuration profile. | |
| 1.3.6.1.2.1.10.251.2.1.17 | Groupxdsl2ChConfProfileAtmGroup | current | The group of configuration objects required when the data path is ATM. | |
| 1.3.6.1.2.1.10.251.2.1.18 | Groupxdsl2ChConfProfileMinResGroup | current | The group of configuration objects required for the reserved data rate. | |
| 1.3.6.1.2.1.10.251.2.1.19 | Groupxdsl2ChConfProfileOptAttrGroup | current | The group of various optional channel configuration parameters. | |
| 1.3.6.1.2.1.10.251.2.1.20 | Groupxdsl2LineAlarmConfTemplateGroup | current | The group of objects in a line alarm template. | |
| 1.3.6.1.2.1.10.251.2.1.21 | Groupxdsl2LineAlarmConfProfileGroup | current | The group of objects in a line alarm profile. | |
| 1.3.6.1.2.1.10.251.2.1.22 | Groupxdsl2ChAlarmConfProfileGroup | current | The group of objects in a channel alarm profile. | |
| 1.3.6.1.2.1.10.251.2.1.23 | Groupxdsl2PMLineCurrGroup | current | The group of objects that report the line-level counters for current PM intervals. | |
| 1.3.6.1.2.1.10.251.2.1.24 | Groupxdsl2PMLineInitCurrGroup | current | The group of objects that report the full initialization counters for current PM intervals. | |
| 1.3.6.1.2.1.10.251.2.1.25 | Groupxdsl2PMLineInitCurrShortGroup | current | The group of objects that report the short initialization counters for current PM intervals. | |
| 1.3.6.1.2.1.10.251.2.1.26 | Groupxdsl2PMLineHist15MinGroup | current | The group of line-level PM counters for the previous 15-minute intervals. | |
| 1.3.6.1.2.1.10.251.2.1.27 | Groupxdsl2PMLineHist1DayGroup | current | The group of line-level PM counters for the previous 24-hour intervals. | |
| 1.3.6.1.2.1.10.251.2.1.28 | Groupxdsl2PMLineInitHist15MinGroup | current | The group of PM counters for the previous 15-minute interval full initializations. | |
| 1.3.6.1.2.1.10.251.2.1.29 | Groupxdsl2PMLineInitHist15MinShortGroup | current | The group of PM counters for the previous 15-minute interval short initializations. | |
| 1.3.6.1.2.1.10.251.2.1.30 | Groupxdsl2PMLineInitHist1DayGroup | current | The group of PM counters for the previous 24-hour interval full initializations. | |
| 1.3.6.1.2.1.10.251.2.1.31 | Groupxdsl2PMLineInitHist1DayShortGroup | current | The group of PM counters for the previous 24-hour interval short initializations. | |
| 1.3.6.1.2.1.10.251.2.1.32 | Groupxdsl2PMChCurrGroup | current | The group of objects that report the channel-level counters for current PM intervals. | |
| 1.3.6.1.2.1.10.251.2.1.33 | Groupxdsl2PMChHist15MinGroup | current | The group of objects that report the channel-level counters for previous 15-minute PM intervals. | |
| 1.3.6.1.2.1.10.251.2.1.34 | Groupxdsl2PMChHist1DGroup | current | The group of objects that report the channel-level counters for previous 24-hour PM intervals. | |
| 1.3.6.1.2.1.10.251.2.1.35 | Groupxdsl2ScalarSCGroup | current | The group of objects that report the available memory resources for DELT processes. | |
| 1.3.6.1.2.1.10.251.2.1.36 | Groupxdsl2ThreshNotificationGroup | current | This group supports notifications of significant conditions associated with DSL lines. | |
| 1.3.6.1.2.1.10.251.2.1.37 | Groupxdsl2StatusChangeNotificationGroup | current | This group supports notifications of thresholds crossing associated with DSL lines. | |
| 1.3.6.1.2.1.10.251.2.2 | Nodexdsl2Compliances | |||
| 1.3.6.1.2.1.10.251.2.2.1 | Compliancexdsl2LineMibCompliance | current | The compliance statement for SNMP entities which manage VDSL2/ADSL/ADSL2 and ADSL2+ interfaces. |