WEBMON-EDGE-MATRIX-MIB
919 objects
WebMon Edge-Matrix MIB.
Imported Objects
| SNMPv2-CONF | NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | enterprises MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-IDENTITY OBJECT-TYPE |
| SNMPv2-TC | TEXTUAL-CONVENTION |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.994 | Nodedantel | |||
| 1.3.6.1.4.1.994.3 | NodedantelProducts | |||
| 1.3.6.1.4.1.994.3.4 | IdentitywebMon | current | The parent node representing the WebMon device. | |
| 1.3.6.1.4.1.994.3.4.3 | IdentitymoduleIdentity | WebMon Edge-Matrix MIB. | ||
| 1.3.6.1.4.1.994.3.4.4 | GroupnotificationGroup | current | Group containing all the notification types. | |
| 1.3.6.1.4.1.994.3.4.5 | GroupobjectGroup | current | Group containing all the objects. | |
| 1.3.6.1.4.1.994.3.4.6 | Identitytraps | current | Category containing all the traps. Each trap has sibling data nodes that contain the data associated with the most recently sent trap of that particular type. … | |
| 1.3.6.1.4.1.994.3.4.6.1 | IdentityanalogInputs | current | Subtree containing trap and associated data for analog inputs. Analog inputs measure a value. The input always has a live reading, but traps are only sent on e… | |
| 1.3.6.1.4.1.994.3.4.6.1.1 | NotificationanalogEventTrap | current | Notification sent upon an analog input reading crossing a threshold. | |
| 1.3.6.1.4.1.994.3.4.6.1.2 | ScalaranalogInputDescription | read-only | current | Description of the analog input. |
| 1.3.6.1.4.1.994.3.4.6.1.3 | ScalaranalogLiveLevel | read-only | current | The level associated with the analogLiveReading for this input. |
| 1.3.6.1.4.1.994.3.4.6.1.5 | ScalaranalogLiveReading | read-only | current | The reading from the analog input described by analogInputDescription at the time the trap was sent. It is in the units described in analogUnitsOfMeasurement. |
| 1.3.6.1.4.1.994.3.4.6.1.6 | ScalaranalogUnitsOfMeasurement | read-only | current | The units of measurement associated with the analogLiveReading. |
| 1.3.6.1.4.1.994.3.4.6.1.7 | ScalaranalogLiveState | read-only | current | The state associated with analogLiveReading. |
| 1.3.6.1.4.1.994.3.4.6.1.8 | ScalaranalogLiveStateDescription | read-only | current | The description of the range in which the analogLiveReading is. |
| 1.3.6.1.4.1.994.3.4.6.1.9 | ScalaranalogAlarmState | read-only | current | If true this field indicates the alarmed state. If false this field indicates the not alarmed state. |
| 1.3.6.1.4.1.994.3.4.6.1.101 | ScalaranalogSourceDescription | not-accessible | current | Description of the event source. |
| 1.3.6.1.4.1.994.3.4.6.1.102 | ScalaranalogSourceIndex | not-accessible | current | Index of the event source. |
| 1.3.6.1.4.1.994.3.4.6.2 | IdentitydigitalInputs | current | Subtree containing trap and associated data for digital inputs. Digital inputs monitor a binary state. The input is always in one of two states. Traps are sent… | |
| 1.3.6.1.4.1.994.3.4.6.2.1 | NotificationdigitalEventTrap | current | Notification sent upon change of state on a digital input. | |
| 1.3.6.1.4.1.994.3.4.6.2.2 | ScalardigitalInputDescription | read-only | current | Description of the digital input. |
| 1.3.6.1.4.1.994.3.4.6.2.3 | ScalardigitalLiveLevel | read-only | current | The level associated with digitalLiveState for this input. |
| 1.3.6.1.4.1.994.3.4.6.2.4 | ScalardigitalLiveState | read-only | current | The state of the digital input described by digitalInputDescription at the time the trap was sent. |
| 1.3.6.1.4.1.994.3.4.6.2.5 | ScalardigitalLiveStateDescription | read-only | current | The description of the digitalLiveState. |
| 1.3.6.1.4.1.994.3.4.6.2.6 | ScalardigitalAlarmState | read-only | current | If true this field indicates the alarmed state. If false this field indicates the not alarmed state. |
| 1.3.6.1.4.1.994.3.4.6.2.101 | ScalardigitalSourceDescription | not-accessible | current | Description of the event source. |
| 1.3.6.1.4.1.994.3.4.6.2.102 | ScalardigitalSourceIndex | not-accessible | current | Index of the event source. |
| 1.3.6.1.4.1.994.3.4.6.3 | IdentityremoteDevices | current | Subtree containing trap and associated data for monitored remote devices. Remote devices are monitored for network connectivity. The device's live state is alw… | |
| 1.3.6.1.4.1.994.3.4.6.3.1 | NotificationremoteDeviceEventTrap | current | Notification sent upon change of state of a remote device. | |
| 1.3.6.1.4.1.994.3.4.6.3.2 | ScalarremoteDeviceDescription | read-only | current | Description of the remote device. |
| 1.3.6.1.4.1.994.3.4.6.3.3 | ScalarremoteDeviceLiveLevel | read-only | current | The level associated with remoteDeviceLiveState. |
| 1.3.6.1.4.1.994.3.4.6.3.4 | ScalarremoteDeviceLiveState | read-only | current | The state of the remote device described by remoteDeviceDescription at the time the trap was sent. Online indicates connected, offline indicates not connected. |
| 1.3.6.1.4.1.994.3.4.6.3.5 | ScalarremoteDeviceAlarmState | read-only | current | If true this field indicates the alarmed state. If false this field indicates the not alarmed state. |
| 1.3.6.1.4.1.994.3.4.6.3.101 | ScalarremoteDeviceSourceDescription | not-accessible | current | Description of the event source. |
| 1.3.6.1.4.1.994.3.4.6.3.102 | ScalarremoteDeviceSourceIndex | not-accessible | current | Index of the event source. |
| 1.3.6.1.4.1.994.3.4.6.4 | Identityfaults | current | Subtree containing trap and associated data for faults. Faults are conditions internal to the WebMon. The only data associated with this trap is a string that … | |
| 1.3.6.1.4.1.994.3.4.6.4.1 | NotificationfaultTrap | current | Notification sent when a fault is encountered. | |
| 1.3.6.1.4.1.994.3.4.6.4.2 | ScalarfaultDescription | read-only | current | Description of the condition at the WebMon. |
| 1.3.6.1.4.1.994.3.4.6.4.3 | ScalarfaultLiveLevel | read-only | current | The level associated with faultStateDescription. |
| 1.3.6.1.4.1.994.3.4.6.4.4 | ScalarfaultStateDescription | read-only | current | The description of the state of this fault. |
| 1.3.6.1.4.1.994.3.4.6.4.5 | ScalarfaultAlarmState | read-only | current | If true this field indicates the alarmed state. If false this field indicates the not alarmed state. |
| 1.3.6.1.4.1.994.3.4.6.4.101 | ScalarfaultSourceDescription | not-accessible | current | Description of the event source. |
| 1.3.6.1.4.1.994.3.4.6.4.102 | ScalarfaultSourceIndex | not-accessible | current | Index of the event source. |
| 1.3.6.1.4.1.994.3.4.7 | Nodeconfiguration | |||
| 1.3.6.1.4.1.994.3.4.7.1 | NodesystemGeneral | |||
| 1.3.6.1.4.1.994.3.4.7.1.2 | ScalarsystemGeneralLocation | read-write | current | Location on the device. |
| 1.3.6.1.4.1.994.3.4.7.1.3 | ScalarsystemGeneralDescription | read-write | current | Description of the device. |
| 1.3.6.1.4.1.994.3.4.7.1.14 | ScalarsystemGeneralIpAddress | read-write | current | IP Address of the device. If changed, the new IP address will only take effect after a reset. |
| 1.3.6.1.4.1.994.3.4.7.1.15 | ScalarsystemGeneralSubnetMask | read-write | current | Subnet Mask of the device. If changed, the new IP address will only take effect after a reset. |
| 1.3.6.1.4.1.994.3.4.7.1.16 | ScalarsystemGeneralGatewayAddress | read-write | current | Gateway Address of the device. If changed, the new IP address will only take effect after a reset. |
| 1.3.6.1.4.1.994.3.4.7.1.23 | ScalarsystemGeneralReadPeriod | read-write | current | The number of minutes until the WebMon resets itself. |
| 1.3.6.1.4.1.994.3.4.7.1.45 | ScalarsystemGeneralMeasureStyle | read-write | current | Determines if units are displayed in English or Metric. |
| 1.3.6.1.4.1.994.3.4.7.1.54 | ScalarsystemGeneralMacAddress | read-only | current | The MAC address of the device. |
| 1.3.6.1.4.1.994.3.4.7.1.70 | ScalarsystemGeneralProductType | read-only | current | Describes the type of device. |
| 1.3.6.1.4.1.994.3.4.7.1.73 | ScalarsystemGeneralIPPortNum | read-write | current | IP port number to use when connecting to the web page (HTTP). |
| 1.3.6.1.4.1.994.3.4.7.1.82 | ScalarsystemGeneralVersion | read-only | current | The version of the running software. |
| 1.3.6.1.4.1.994.3.4.7.1.98 | ScalarsystemGeneralUseResetTime | read-write | current | If enabled, the WebMon will reset periodically. |
| 1.3.6.1.4.1.994.3.4.7.1.147 | ScalarsystemGeneralEthernetType | read-write | current | Ethernet duplex type of the device. If changed, the new duplex type will only take effect after a reset. |
| 1.3.6.1.4.1.994.3.4.7.1.148 | ScalarsystemGeneralEthernetRate | read-write | current | Ethernet rate of the device. If changed, the new rate will only take effect after a reset. |
| 1.3.6.1.4.1.994.3.4.7.1.149 | ScalarsystemGeneralContact | read-write | current | SNMP contact information. |
| 1.3.6.1.4.1.994.3.4.7.2 | TablepTrapTargetTable | not-accessible | current | Table for configuration of TrapTarget |
| 1.3.6.1.4.1.994.3.4.7.2.1 | RowpTrapTargetEntry | not-accessible | current | Entry for configuration table of TrapTarget |
| 1.3.6.1.4.1.994.3.4.7.2.1.3 | ColumnpTrapTargetDescription | read-write | current | Description of the trap target. |
| 1.3.6.1.4.1.994.3.4.7.2.1.10 | ColumnpTrapTargetConfigured | read-write | current | Determines if traps will be sent to trap target with given IP address. |
| 1.3.6.1.4.1.994.3.4.7.2.1.14 | ColumnpTrapTargetIpAddress | read-write | current | SNMP traps are sent to this IP address. |
| 1.3.6.1.4.1.994.3.4.7.2.1.42 | ColumnpTrapTargetSnmpVersion | read-write | current | Indicates the version of SNMP trap to use. |
| 1.3.6.1.4.1.994.3.4.7.2.1.73 | ColumnpTrapTargetIPPortNum | read-write | current | SNMP traps are sent to this network port. |
| 1.3.6.1.4.1.994.3.4.7.2.1.78 | ColumnpTrapTargetBackupIPAddress | read-write | current | Used only when dialing out as backup. |
| 1.3.6.1.4.1.994.3.4.7.2.1.125 | ColumnpTrapTargetUseDialout | read-write | current | Determines if traps will be sent only when dialed out. |
| 1.3.6.1.4.1.994.3.4.7.2.1.126 | ColumnpTrapTargetDialoutTarget | read-write | current | Determines which target to dial out to when sending traps. |
| 1.3.6.1.4.1.994.3.4.7.2.1.140 | ColumnpTrapTargetAuthKey | read-write | current | |
| 1.3.6.1.4.1.994.3.4.7.2.1.141 | ColumnpTrapTargetPrivKey | read-write | current | |
| 1.3.6.1.4.1.994.3.4.7.2.1.142 | ColumnpTrapTargetSNMPAccess | read-write | current | |
| 1.3.6.1.4.1.994.3.4.7.2.1.143 | ColumnpTrapTargetEngineID | read-write | current | |
| 1.3.6.1.4.1.994.3.4.7.2.1.999 | ColumnpTrapTargetIndex | read-only | current | Index. |
| 1.3.6.1.4.1.994.3.4.7.3 | TablepEmailTable | not-accessible | current | Table for configuration of Email |
| 1.3.6.1.4.1.994.3.4.7.3.1 | RowpEmailEntry | not-accessible | current | Entry for configuration table of Email |
| 1.3.6.1.4.1.994.3.4.7.3.1.1 | ColumnpEmailAddress | read-write | current | Email events will be sent to this address. |
| 1.3.6.1.4.1.994.3.4.7.3.1.3 | ColumnpEmailDescription | read-write | current | Description of the Email target. |
| 1.3.6.1.4.1.994.3.4.7.3.1.10 | ColumnpEmailConfigured | read-write | current | If set to true, email events will be sent to given address. If set to false, email will not be sent. |
| 1.3.6.1.4.1.994.3.4.7.3.1.999 | ColumnpEmailIndex | read-only | current | Index. |
| 1.3.6.1.4.1.994.3.4.7.5 | TablepRemoteSensorTable | not-accessible | current | Table for configuration of RemoteSensor |
| 1.3.6.1.4.1.994.3.4.7.5.1 | RowpRemoteSensorEntry | not-accessible | current | Entry for configuration table of RemoteSensor |
| 1.3.6.1.4.1.994.3.4.7.5.1.3 | ColumnpRemoteSensorDescription | read-write | current | Description of the Analog device. |
| 1.3.6.1.4.1.994.3.4.7.5.1.4 | ColumnpRemoteSensorDesc0 | read-write | current | The description for values between threshold 0 and threshold 1. |
| 1.3.6.1.4.1.994.3.4.7.5.1.5 | ColumnpRemoteSensorDesc1 | read-write | current | The description for values between threshold 1 and threshold 2. |
| 1.3.6.1.4.1.994.3.4.7.5.1.6 | ColumnpRemoteSensorDesc2 | read-write | current | The description for values between threshold 2 and threshold 3. |
| 1.3.6.1.4.1.994.3.4.7.5.1.7 | ColumnpRemoteSensorDesc3 | read-write | current | The description for values between threshold 3 and threshold 4. |
| 1.3.6.1.4.1.994.3.4.7.5.1.8 | ColumnpRemoteSensorDesc4 | read-write | current | The description for values between threshold 4 and threshold 5. |
| 1.3.6.1.4.1.994.3.4.7.5.1.9 | ColumnpRemoteSensorDesc5 | read-write | current | Description for a communications failure to the remote analog device. |
| 1.3.6.1.4.1.994.3.4.7.5.1.10 | ColumnpRemoteSensorConfigured | read-write | current | If set to true analog values will be monitored. If set to false no values will be monitored. |
| 1.3.6.1.4.1.994.3.4.7.5.1.11 | ColumnpRemoteSensorSendEmail | read-write | current | If set to true an email event will be set when a threshold is crossed. If set to false no email event will be sent. |
| 1.3.6.1.4.1.994.3.4.7.5.1.12 | ColumnpRemoteSensorSendSNMPTrap | read-write | current | If set to true an SNMP trap will be set when a threshold is crossed. If set to false no SNMP trap will be sent. |
| 1.3.6.1.4.1.994.3.4.7.5.1.17 | ColumnpRemoteSensorLevel0 | read-write | current | The level for values between threshold 0 and threshold 1. |
| 1.3.6.1.4.1.994.3.4.7.5.1.18 | ColumnpRemoteSensorLevel1 | read-write | current | The level for values between threshold 1 and threshold 2. |
| 1.3.6.1.4.1.994.3.4.7.5.1.19 | ColumnpRemoteSensorLevel2 | read-write | current | The level for values between threshold 2 and threshold 3. |
| 1.3.6.1.4.1.994.3.4.7.5.1.20 | ColumnpRemoteSensorLevel3 | read-write | current | The level for values between threshold 3 and threshold 4. |
| 1.3.6.1.4.1.994.3.4.7.5.1.21 | ColumnpRemoteSensorLevel4 | read-write | current | The level for values between threshold 4 and threshold 5. |
| 1.3.6.1.4.1.994.3.4.7.5.1.22 | ColumnpRemoteSensorLevel5 | read-write | current | Level of a communications failure to the remote analog device. |
| 1.3.6.1.4.1.994.3.4.7.5.1.28 | ColumnpRemoteSensorThresh0 | read-write | current | This is the maximum analog value. |
| 1.3.6.1.4.1.994.3.4.7.5.1.29 | ColumnpRemoteSensorThresh1 | read-write | current | This is the first threshold value. |
| 1.3.6.1.4.1.994.3.4.7.5.1.30 | ColumnpRemoteSensorThresh2 | read-write | current | This is the second threshold value. |
| 1.3.6.1.4.1.994.3.4.7.5.1.31 | ColumnpRemoteSensorThresh3 | read-write | current | This is the third threshold value. |
| 1.3.6.1.4.1.994.3.4.7.5.1.32 | ColumnpRemoteSensorThresh4 | read-write | current | This is the fourth threshold value. |
| 1.3.6.1.4.1.994.3.4.7.5.1.33 | ColumnpRemoteSensorThresh5 | read-write | current | This is the minimum threshold value. |
| 1.3.6.1.4.1.994.3.4.7.5.1.46 | ColumnpRemoteSensorUnits | read-write | current | Description of the units of measurement. |
| 1.3.6.1.4.1.994.3.4.7.5.1.56 | ColumnpRemoteSensorPollAddress | read-write | current | The polling address of the analog device. |
| 1.3.6.1.4.1.994.3.4.7.5.1.64 | ColumnpRemoteSensorLiveDescription | read-only | current | The description of the current state of the analog device |
| 1.3.6.1.4.1.994.3.4.7.5.1.65 | ColumnpRemoteSensorLiveLevel | read-only | current | The level of the current state of the analog device. |
| 1.3.6.1.4.1.994.3.4.7.5.1.66 | ColumnpRemoteSensorLiveRaw | read-only | current | The current reading from the analog device. This value will always be between the threshold 0 and threshold 5 values. |
| 1.3.6.1.4.1.994.3.4.7.5.1.67 | ColumnpRemoteSensorLiveTime | read-only | current | The time of the last event. |
| 1.3.6.1.4.1.994.3.4.7.5.1.116 | ColumnpRemoteSensorTL1SID | read-write | current | (TL1) System ID associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.5.1.117 | ColumnpRemoteSensorTL1COND | read-write | current | (TL1) Condition text associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.5.1.118 | ColumnpRemoteSensorTL1Eqpt | read-write | current | (TL1) EQPT field associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.5.1.119 | ColumnpRemoteSensorTL1Env | read-write | current | (TL1) Environmental field associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.5.1.120 | ColumnpRemoteSensorTL1Srveff | read-write | current | (TL1) Service Effecting field associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.5.1.121 | ColumnpRemoteSensorTL1Locn | read-write | current | (TL1) Location field associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.5.1.122 | ColumnpRemoteSensorTL1Dirn | read-write | current | (TL1) Direction field associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.5.1.144 | ColumnpRemoteSensorMODBUSCommand | read-write | current | The polling command for the analog device. |
| 1.3.6.1.4.1.994.3.4.7.5.1.145 | ColumnpRemoteSensorStartRegister | read-write | current | The MODBUS register for the analog device. |
| 1.3.6.1.4.1.994.3.4.7.5.1.999 | ColumnpRemoteSensorIndex | read-only | current | Index. |
| 1.3.6.1.4.1.994.3.4.7.6 | TablepOnboardSensorTable | not-accessible | current | Table for configuration of OnboardSensor |
| 1.3.6.1.4.1.994.3.4.7.6.1 | RowpOnboardSensorEntry | not-accessible | current | Entry for configuration table of OnboardSensor |
| 1.3.6.1.4.1.994.3.4.7.6.1.3 | ColumnpOnboardSensorDescription | read-only | current | Description of the onboard sensor input. |
| 1.3.6.1.4.1.994.3.4.7.6.1.4 | ColumnpOnboardSensorDesc0 | read-write | current | The description for values between threshold 0 and threshold 1. |
| 1.3.6.1.4.1.994.3.4.7.6.1.5 | ColumnpOnboardSensorDesc1 | read-write | current | The description for values between threshold 1 and threshold 2. |
| 1.3.6.1.4.1.994.3.4.7.6.1.6 | ColumnpOnboardSensorDesc2 | read-write | current | The description for values between threshold 2 and threshold 3. |
| 1.3.6.1.4.1.994.3.4.7.6.1.7 | ColumnpOnboardSensorDesc3 | read-write | current | The description for values between threshold 3 and threshold 4. |
| 1.3.6.1.4.1.994.3.4.7.6.1.8 | ColumnpOnboardSensorDesc4 | read-write | current | The description for values between threshold 4 and threshold 5. |
| 1.3.6.1.4.1.994.3.4.7.6.1.9 | ColumnpOnboardSensorDesc5 | read-write | current | Description for a communications failure to the sensor. |
| 1.3.6.1.4.1.994.3.4.7.6.1.10 | ColumnpOnboardSensorConfigured | read-write | current | If set to true, the sensor input will be usable. If set to false the sensor input will be ignored. |
| 1.3.6.1.4.1.994.3.4.7.6.1.11 | ColumnpOnboardSensorSendEmail | read-write | current | If set to true an email event will be set when a threshold is crossed. If set to false no email event will be sent. |
| 1.3.6.1.4.1.994.3.4.7.6.1.12 | ColumnpOnboardSensorSendSNMPTrap | read-write | current | If set to true an SNMP trap will be set when a threshold is crossed. If set to false no SNMP trap will be sent. |
| 1.3.6.1.4.1.994.3.4.7.6.1.17 | ColumnpOnboardSensorLevel0 | read-write | current | The level for values between threshold 0 and threshold 1. |
| 1.3.6.1.4.1.994.3.4.7.6.1.18 | ColumnpOnboardSensorLevel1 | read-write | current | The level for values between threshold 1 and threshold 2. |
| 1.3.6.1.4.1.994.3.4.7.6.1.19 | ColumnpOnboardSensorLevel2 | read-write | current | The level for values between threshold 2 and threshold 3. |
| 1.3.6.1.4.1.994.3.4.7.6.1.20 | ColumnpOnboardSensorLevel3 | read-write | current | The level for values between threshold 3 and threshold 4. |
| 1.3.6.1.4.1.994.3.4.7.6.1.21 | ColumnpOnboardSensorLevel4 | read-write | current | The level for values between threshold 4 and threshold 5. |
| 1.3.6.1.4.1.994.3.4.7.6.1.22 | ColumnpOnboardSensorLevel5 | read-write | current | Level of a communications failure to the sensor. |
| 1.3.6.1.4.1.994.3.4.7.6.1.28 | ColumnpOnboardSensorThresh0 | read-only | current | This is the minimun analog value. |
| 1.3.6.1.4.1.994.3.4.7.6.1.29 | ColumnpOnboardSensorThresh1 | read-write | current | This is the first threshold value. |
| 1.3.6.1.4.1.994.3.4.7.6.1.30 | ColumnpOnboardSensorThresh2 | read-write | current | This is the second threshold value. |
| 1.3.6.1.4.1.994.3.4.7.6.1.31 | ColumnpOnboardSensorThresh3 | read-write | current | This is the third threshold value. |
| 1.3.6.1.4.1.994.3.4.7.6.1.32 | ColumnpOnboardSensorThresh4 | read-write | current | This is the fourth threshold value. |
| 1.3.6.1.4.1.994.3.4.7.6.1.33 | ColumnpOnboardSensorThresh5 | read-only | current | This is the maximum threshold value. |
| 1.3.6.1.4.1.994.3.4.7.6.1.46 | ColumnpOnboardSensorUnits | read-only | current | Description of the units of measurement. |
| 1.3.6.1.4.1.994.3.4.7.6.1.64 | ColumnpOnboardSensorLiveDescription | read-only | current | The description of the current state of the onboard sensor |
| 1.3.6.1.4.1.994.3.4.7.6.1.65 | ColumnpOnboardSensorLiveLevel | read-only | current | The level of the current state of the onboard sensor. |
| 1.3.6.1.4.1.994.3.4.7.6.1.66 | ColumnpOnboardSensorLiveRaw | read-only | current | The current reading from the onboard sensor. This value will always be between the threshold 0 and threshold 5 values. |
| 1.3.6.1.4.1.994.3.4.7.6.1.67 | ColumnpOnboardSensorLiveTime | read-only | current | The time of the last event. |
| 1.3.6.1.4.1.994.3.4.7.6.1.116 | ColumnpOnboardSensorTL1SID | read-write | current | (TL1) System ID associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.6.1.117 | ColumnpOnboardSensorTL1COND | read-write | current | (TL1) Condition text associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.6.1.118 | ColumnpOnboardSensorTL1Eqpt | read-write | current | (TL1) EQPT field associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.6.1.119 | ColumnpOnboardSensorTL1Env | read-write | current | (TL1) Environmental field associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.6.1.120 | ColumnpOnboardSensorTL1Srveff | read-write | current | (TL1) Service Effecting field associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.6.1.121 | ColumnpOnboardSensorTL1Locn | read-write | current | (TL1) Location field associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.6.1.122 | ColumnpOnboardSensorTL1Dirn | read-write | current | (TL1) Direction field associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.6.1.131 | ColumnpOnboardSensorSensorType | read-only | current | The type of sensor. |
| 1.3.6.1.4.1.994.3.4.7.6.1.999 | ColumnpOnboardSensorIndex | read-only | current | Index. |
| 1.3.6.1.4.1.994.3.4.7.7 | TablepNetDevicesTable | not-accessible | current | Table for configuration of NetDevices |
| 1.3.6.1.4.1.994.3.4.7.7.1 | RowpNetDevicesEntry | not-accessible | current | Entry for configuration table of NetDevices |
| 1.3.6.1.4.1.994.3.4.7.7.1.3 | ColumnpNetDevicesDescription | read-write | current | Description of the network device. |
| 1.3.6.1.4.1.994.3.4.7.7.1.4 | ColumnpNetDevicesDesc0 | read-write | current | Text description of online state. |
| 1.3.6.1.4.1.994.3.4.7.7.1.5 | ColumnpNetDevicesDesc1 | read-write | current | Text description of offline state. |
| 1.3.6.1.4.1.994.3.4.7.7.1.10 | ColumnpNetDevicesConfigured | read-write | current | If set to true, net device will be pinged, If set to false, no action will be taken. |
| 1.3.6.1.4.1.994.3.4.7.7.1.11 | ColumnpNetDevicesSendEmail | read-write | current | If set to true, an email will be sent when a change of state is detected. If set to false, no email will be sent. |
| 1.3.6.1.4.1.994.3.4.7.7.1.12 | ColumnpNetDevicesSendSNMPTrap | read-write | current | If set to true, an SNMP trap will be sent when a change of state is detected. If set to false, no SNMP trap will be sent. |
| 1.3.6.1.4.1.994.3.4.7.7.1.14 | ColumnpNetDevicesIpAddress | read-write | current | The IP address of the net device to ping. |
| 1.3.6.1.4.1.994.3.4.7.7.1.17 | ColumnpNetDevicesLevel0 | read-write | current | Alarm level associated with the online state. |
| 1.3.6.1.4.1.994.3.4.7.7.1.18 | ColumnpNetDevicesLevel1 | read-write | current | Alarm level associated with the offline state. |
| 1.3.6.1.4.1.994.3.4.7.7.1.64 | ColumnpNetDevicesLiveDescription | read-only | current | The description of the current state of the net device |
| 1.3.6.1.4.1.994.3.4.7.7.1.65 | ColumnpNetDevicesLiveLevel | read-only | current | The level of the current state of the net device. |
| 1.3.6.1.4.1.994.3.4.7.7.1.66 | ColumnpNetDevicesLiveRaw | read-only | current | The current reading from the net device. This value will always be between the threshold 0 and threshold 5 values. |
| 1.3.6.1.4.1.994.3.4.7.7.1.67 | ColumnpNetDevicesLiveTime | read-only | current | The time of the last event. |
| 1.3.6.1.4.1.994.3.4.7.7.1.116 | ColumnpNetDevicesTL1SID | read-write | current | (TL1) System ID associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.7.1.117 | ColumnpNetDevicesTL1COND | read-write | current | (TL1) Condition text associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.7.1.118 | ColumnpNetDevicesTL1Eqpt | read-write | current | (TL1) EQPT field associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.7.1.119 | ColumnpNetDevicesTL1Env | read-write | current | (TL1) Environmental field associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.7.1.120 | ColumnpNetDevicesTL1Srveff | read-write | current | (TL1) Service Effecting field associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.7.1.121 | ColumnpNetDevicesTL1Locn | read-write | current | (TL1) Location field associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.7.1.122 | ColumnpNetDevicesTL1Dirn | read-write | current | (TL1) Direction field associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.7.1.999 | ColumnpNetDevicesIndex | read-only | current | Index. |
| 1.3.6.1.4.1.994.3.4.7.9 | TablepAccountsTable | not-accessible | current | Table for configuration of Accounts |
| 1.3.6.1.4.1.994.3.4.7.9.1 | RowpAccountsEntry | not-accessible | current | Entry for configuration table of Accounts |
| 1.3.6.1.4.1.994.3.4.7.9.1.10 | ColumnpAccountsConfigured | read-write | current | If set to true, this account can be used to login. |
| 1.3.6.1.4.1.994.3.4.7.9.1.25 | ColumnpAccountsName | read-write | current | Name associated with this account. |
| 1.3.6.1.4.1.994.3.4.7.9.1.27 | ColumnpAccountsEncPassword | read-write | current | Password for this account. When reading, an encrypted version of password will be displayed. When writing, use plain text. |
| 1.3.6.1.4.1.994.3.4.7.9.1.55 | ColumnpAccountsUserLevel | read-write | current | The user level for this account. One of the following masks from each group are used: No FTP access 0x0000 0 FTP read-only 0x0001 1 FTP Full access 0x0003 3 No… |
| 1.3.6.1.4.1.994.3.4.7.9.1.77 | ColumnpAccountsUnsecured | read-write | current | Allow secured configuration for SNMP through this account. |
| 1.3.6.1.4.1.994.3.4.7.9.1.140 | ColumnpAccountsAuthKey | read-write | current | |
| 1.3.6.1.4.1.994.3.4.7.9.1.141 | ColumnpAccountsPrivKey | read-write | current | |
| 1.3.6.1.4.1.994.3.4.7.9.1.142 | ColumnpAccountsSNMPAccess | read-write | current | |
| 1.3.6.1.4.1.994.3.4.7.9.1.999 | ColumnpAccountsIndex | read-only | current | Index. |
| 1.3.6.1.4.1.994.3.4.7.10 | Nodecamera | |||
| 1.3.6.1.4.1.994.3.4.7.10.10 | ScalarcameraConfigured | read-write | current | If set to true, camera view will be used in main webpage. If set to false, camera view will not be used. |
| 1.3.6.1.4.1.994.3.4.7.10.14 | ScalarcameraIpAddress | read-write | current | IP address of the camera. |
| 1.3.6.1.4.1.994.3.4.7.10.43 | ScalarcameraCameraStyle | read-write | current | Type of camera used. |
| 1.3.6.1.4.1.994.3.4.7.12 | NodesnmpGeneral | |||
| 1.3.6.1.4.1.994.3.4.7.12.10 | ScalarsnmpGeneralConfigured | read-write | current | Resend standing alarms at a given interval |
| 1.3.6.1.4.1.994.3.4.7.12.23 | ScalarsnmpGeneralReadPeriod | read-write | current | Period in minutes between resend of standing alarms |
| 1.3.6.1.4.1.994.3.4.7.12.39 | ScalarsnmpGeneralGet | read-write | current | Get community name for SNMP. |
| 1.3.6.1.4.1.994.3.4.7.12.40 | ScalarsnmpGeneralSet | read-write | current | Set community name for SNMP. |
| 1.3.6.1.4.1.994.3.4.7.12.41 | ScalarsnmpGeneralTrap | read-write | current | Trap community name for SNMP. |
| 1.3.6.1.4.1.994.3.4.7.12.73 | ScalarsnmpGeneralIPPortNum | read-write | current | SNMP configuration is done on this network port. |
| 1.3.6.1.4.1.994.3.4.7.12.143 | ScalarsnmpGeneralEngineID | read-only | current | SNMP v3 engine ID |
| 1.3.6.1.4.1.994.3.4.7.13 | NodeemailGeneral | |||
| 1.3.6.1.4.1.994.3.4.7.13.1 | ScalaremailGeneralAddress | read-write | current | Login name to use if logging into email server is true. |
| 1.3.6.1.4.1.994.3.4.7.13.10 | ScalaremailGeneralConfigured | read-write | current | If set to true, the device will log onto the email server before sending and email event. If set to false, the device will not log onto email server. |
| 1.3.6.1.4.1.994.3.4.7.13.14 | ScalaremailGeneralIpAddress | read-write | current | IP address of email server. |
| 1.3.6.1.4.1.994.3.4.7.13.26 | ScalaremailGeneralPassword | read-write | current | Password to use if logging into email server is true. |
| 1.3.6.1.4.1.994.3.4.7.13.73 | ScalaremailGeneralIPPortNum | read-write | current | Port number address of email server. |
| 1.3.6.1.4.1.994.3.4.7.14 | TablepSerialTable | not-accessible | current | Table for configuration of Serial |
| 1.3.6.1.4.1.994.3.4.7.14.1 | RowpSerialEntry | not-accessible | current | Entry for configuration table of Serial |
| 1.3.6.1.4.1.994.3.4.7.14.1.3 | ColumnpSerialDescription | read-only | current | Description of the serial port. |
| 1.3.6.1.4.1.994.3.4.7.14.1.10 | ColumnpSerialConfigured | read-write | current | If set to true, this serial port will be usable. If set to false the port will not be usable. |
| 1.3.6.1.4.1.994.3.4.7.14.1.14 | ColumnpSerialIpAddress | read-write | current | IP Address of the target device. |
| 1.3.6.1.4.1.994.3.4.7.14.1.23 | ColumnpSerialReadPeriod | read-write | current | Inactivity timeout (in minutes). |
| 1.3.6.1.4.1.994.3.4.7.14.1.57 | ColumnpSerialBaudRate | read-write | current | Baud rate of the serial port. |
| 1.3.6.1.4.1.994.3.4.7.14.1.58 | ColumnpSerialDataBits | read-write | current | Number of data bit for the serial port. |
| 1.3.6.1.4.1.994.3.4.7.14.1.59 | ColumnpSerialParity | read-write | current | Parity of the serial port. |
| 1.3.6.1.4.1.994.3.4.7.14.1.60 | ColumnpSerialStopBits | read-write | current | Number of stop bits for the serial port. |
| 1.3.6.1.4.1.994.3.4.7.14.1.61 | ColumnpSerialProtocol | read-write | current | Protocol the serial port is speaking. |
| 1.3.6.1.4.1.994.3.4.7.14.1.62 | ColumnpSerialSerialRTS | read-write | current | Request To Send (RTS) setting for the serial port. |
| 1.3.6.1.4.1.994.3.4.7.14.1.63 | ColumnpSerialSerialCTS | read-write | current | Clear To Send (CTS) setting for the serial port. |
| 1.3.6.1.4.1.994.3.4.7.14.1.68 | ColumnpSerialPresent | read-only | current | If set to true, the serial port exists. If set to false the serial port does not exist. |
| 1.3.6.1.4.1.994.3.4.7.14.1.73 | ColumnpSerialIPPortNum | read-write | current | IP port number of the target device. |
| 1.3.6.1.4.1.994.3.4.7.14.1.76 | ColumnpSerialPortType | read-only | current | The type of serial port. |
| 1.3.6.1.4.1.994.3.4.7.14.1.999 | ColumnpSerialIndex | read-only | current | Index. |
| 1.3.6.1.4.1.994.3.4.7.15 | TablepSelfTestTable | not-accessible | current | Table for configuration of SelfTest |
| 1.3.6.1.4.1.994.3.4.7.15.1 | RowpSelfTestEntry | not-accessible | current | Entry for configuration table of SelfTest |
| 1.3.6.1.4.1.994.3.4.7.15.1.3 | ColumnpSelfTestDescription | read-write | current | Description of the Power On Self Test (POST). |
| 1.3.6.1.4.1.994.3.4.7.15.1.10 | ColumnpSelfTestConfigured | read-write | current | If set to true, this POST has passed. If set to false, it has failed. |
| 1.3.6.1.4.1.994.3.4.7.15.1.999 | ColumnpSelfTestIndex | read-only | current | Index. |
| 1.3.6.1.4.1.994.3.4.7.16 | TablepInternalFaultsTable | not-accessible | current | Table for configuration of InternalFaults |
| 1.3.6.1.4.1.994.3.4.7.16.1 | RowpInternalFaultsEntry | not-accessible | current | Entry for configuration table of InternalFaults |
| 1.3.6.1.4.1.994.3.4.7.16.1.3 | ColumnpInternalFaultsDescription | read-only | current | Description of the internal fault. |
| 1.3.6.1.4.1.994.3.4.7.16.1.4 | ColumnpInternalFaultsDesc0 | read-only | current | Text description of the healthy state. |
| 1.3.6.1.4.1.994.3.4.7.16.1.5 | ColumnpInternalFaultsDesc1 | read-only | current | Text description of a non-normal state. |
| 1.3.6.1.4.1.994.3.4.7.16.1.6 | ColumnpInternalFaultsDesc2 | read-only | current | Text description of a non-normal state. |
| 1.3.6.1.4.1.994.3.4.7.16.1.7 | ColumnpInternalFaultsDesc3 | read-only | current | Text description of a non-normal state. |
| 1.3.6.1.4.1.994.3.4.7.16.1.11 | ColumnpInternalFaultsSendEmail | read-write | current | If set to true an email event will be set when a change occurs. If set to false no email event will be sent. |
| 1.3.6.1.4.1.994.3.4.7.16.1.12 | ColumnpInternalFaultsSendSNMPTrap | read-write | current | If set to true an SNMP trap will be set when a change occurs. If set to false no SNMP trap will be sent. |
| 1.3.6.1.4.1.994.3.4.7.16.1.17 | ColumnpInternalFaultsLevel0 | read-write | current | Alarm level associated with the healthy state. |
| 1.3.6.1.4.1.994.3.4.7.16.1.18 | ColumnpInternalFaultsLevel1 | read-write | current | Alarm level associated with this non-normal state. |
| 1.3.6.1.4.1.994.3.4.7.16.1.19 | ColumnpInternalFaultsLevel2 | read-write | current | Alarm level associated with this non-normal state. |
| 1.3.6.1.4.1.994.3.4.7.16.1.20 | ColumnpInternalFaultsLevel3 | read-write | current | Alarm level associated with this non-normal state. |
| 1.3.6.1.4.1.994.3.4.7.16.1.23 | ColumnpInternalFaultsReadPeriod | read-write | current | Dwell time required in milliseconds. |
| 1.3.6.1.4.1.994.3.4.7.16.1.50 | ColumnpInternalFaultsIgnoreOff | read-write | current | If true, no event is generated for a change to the healty state. |
| 1.3.6.1.4.1.994.3.4.7.16.1.64 | ColumnpInternalFaultsLiveDescription | read-only | current | The current condition of the internal fault. |
| 1.3.6.1.4.1.994.3.4.7.16.1.65 | ColumnpInternalFaultsLiveLevel | read-only | current | The current level of the internal fault. |
| 1.3.6.1.4.1.994.3.4.7.16.1.67 | ColumnpInternalFaultsLiveTime | read-only | current | The time of the fault event. |
| 1.3.6.1.4.1.994.3.4.7.16.1.98 | ColumnpInternalFaultsUseResetTime | read-only | current | When true the configured dwell time is used internally. |
| 1.3.6.1.4.1.994.3.4.7.16.1.999 | ColumnpInternalFaultsIndex | read-only | current | Index. |
| 1.3.6.1.4.1.994.3.4.7.17 | TablepSlotInfoTable | not-accessible | current | Table for configuration of SlotInfo |
| 1.3.6.1.4.1.994.3.4.7.17.1 | RowpSlotInfoEntry | not-accessible | current | Entry for configuration table of SlotInfo |
| 1.3.6.1.4.1.994.3.4.7.17.1.3 | ColumnpSlotInfoDescription | read-only | current | Description of the slot contents. |
| 1.3.6.1.4.1.994.3.4.7.17.1.35 | ColumnpSlotInfoRecord | read-only | current | The number of records for this slot. |
| 1.3.6.1.4.1.994.3.4.7.17.1.68 | ColumnpSlotInfoPresent | read-only | current | If true indicates a card is in the slot. If false indicates that no card is present in the slot. |
| 1.3.6.1.4.1.994.3.4.7.17.1.69 | ColumnpSlotInfoSlotId | read-only | current | Identifies the type of card in slot. |
| 1.3.6.1.4.1.994.3.4.7.17.1.999 | ColumnpSlotInfoIndex | read-only | current | Index. |
| 1.3.6.1.4.1.994.3.4.7.18 | TablepSlot1Table | not-accessible | current | Table for configuration of Slot1 |
| 1.3.6.1.4.1.994.3.4.7.18.1 | RowpSlot1Entry | not-accessible | current | Entry for configuration table of Slot1 |
| 1.3.6.1.4.1.994.3.4.7.18.1.3 | ColumnpSlot1Description | read-write | current | This field is used in the following card types: discrete-inputs - Description of the alarm point. discrete-outputs - Description of the control point. serial-p… |
| 1.3.6.1.4.1.994.3.4.7.18.1.4 | ColumnpSlot1Desc0 | read-write | current | This field is used in the following card types: discrete-inputs - Description of the off state. discrete-outputs - Description when the control point is open. … |
| 1.3.6.1.4.1.994.3.4.7.18.1.5 | ColumnpSlot1Desc1 | read-write | current | This field is used in the following card types: discrete-inputs - Description of the on state. discrete-outputs - Description when the control point is closed.… |
| 1.3.6.1.4.1.994.3.4.7.18.1.6 | ColumnpSlot1Desc2 | read-write | current | This field is used in the following card types: onboard-sensors - The description for values between threshold 2 and threshold 3. analog-Inputs - The descripti… |
| 1.3.6.1.4.1.994.3.4.7.18.1.7 | ColumnpSlot1Desc3 | read-write | current | This field is used in the following card types: onboard-sensors - The description for values between threshold 3 and threshold 4. analog-Inputs - The descripti… |
| 1.3.6.1.4.1.994.3.4.7.18.1.8 | ColumnpSlot1Desc4 | read-write | current | This field is used in the following card types: onboard-sensors - The description for values between threshold 4 and threshold 5. analog-Inputs - The descripti… |
| 1.3.6.1.4.1.994.3.4.7.18.1.9 | ColumnpSlot1Desc5 | read-write | current | This field is used in the following card types: analog-Inputs - Description for a communications failure to the sensor. analog-Sensors - Description for a comm… |
| 1.3.6.1.4.1.994.3.4.7.18.1.10 | ColumnpSlot1Configured | read-write | current | This field is used in the following card types: discrete-inputs - If set to true, changes of state will be reported. If set to false, not change of states will… |
| 1.3.6.1.4.1.994.3.4.7.18.1.11 | ColumnpSlot1SendEmail | read-write | current | This field is used in the following card types: discrete-inputs - If set to true, an email will be sent on a change of state. If false, no email will be sent. … |
| 1.3.6.1.4.1.994.3.4.7.18.1.12 | ColumnpSlot1SendSNMPTrap | read-write | current | This field is used in the following card types: discrete-inputs - If set to true, an SNMP trap will be sent on a change of state. If false, no SNMP trap will b… |
| 1.3.6.1.4.1.994.3.4.7.18.1.14 | ColumnpSlot1IpAddress | read-write | current | This field is used in the following card types: serial-ports - IP Address of the target device. |
| 1.3.6.1.4.1.994.3.4.7.18.1.17 | ColumnpSlot1Level0 | read-write | current | This field is used in the following card types: discrete-inputs - Level of the off state. discrete-outputs - Level of the control point when open. onboard-sens… |
| 1.3.6.1.4.1.994.3.4.7.18.1.18 | ColumnpSlot1Level1 | read-write | current | This field is used in the following card types: discrete-inputs - Level of the on state. discrete-outputs - Level of the control point when closed. onboard-sen… |
| 1.3.6.1.4.1.994.3.4.7.18.1.19 | ColumnpSlot1Level2 | read-write | current | This field is used in the following card types: onboard-sensors - The level for values between threshold 2 and threshold 3. analog-Inputs - The level for value… |
| 1.3.6.1.4.1.994.3.4.7.18.1.20 | ColumnpSlot1Level3 | read-write | current | This field is used in the following card types: onboard-sensors - The level for values between threshold 3 and threshold 4. analog-Inputs - The level for value… |
| 1.3.6.1.4.1.994.3.4.7.18.1.21 | ColumnpSlot1Level4 | read-write | current | This field is used in the following card types: onboard-sensors - The level for values between threshold 4 and threshold 5. analog-Inputs - The level for value… |
| 1.3.6.1.4.1.994.3.4.7.18.1.22 | ColumnpSlot1Level5 | read-write | current | This field is used in the following card types: analog-Inputs - Level of a communications failure to the sensor. analog-Sensors - Level of a communications fai… |
| 1.3.6.1.4.1.994.3.4.7.18.1.23 | ColumnpSlot1ReadPeriod | read-write | current | This field is used in the following card types: serial-ports - Inactivity timeout (in minutes). |
| 1.3.6.1.4.1.994.3.4.7.18.1.28 | ColumnpSlot1Thresh0 | read-only | current | This field is used in the following card types: onboard-sensors - This is the minimun analog value. analog-Inputs - This is the maximum analog value. analog-Se… |
| 1.3.6.1.4.1.994.3.4.7.18.1.29 | ColumnpSlot1Thresh1 | read-write | current | This field is used in the following card types: onboard-sensors - This is the first threshold value. analog-Inputs - This is the first threshold value. analog-… |
| 1.3.6.1.4.1.994.3.4.7.18.1.30 | ColumnpSlot1Thresh2 | read-write | current | This field is used in the following card types: onboard-sensors - This is the second threshold value. analog-Inputs - This is the second threshold value. analo… |
| 1.3.6.1.4.1.994.3.4.7.18.1.31 | ColumnpSlot1Thresh3 | read-write | current | This field is used in the following card types: onboard-sensors - This is the third threshold value. analog-Inputs - This is the third threshold value. analog-… |
| 1.3.6.1.4.1.994.3.4.7.18.1.32 | ColumnpSlot1Thresh4 | read-write | current | This field is used in the following card types: onboard-sensors - This is the fourth threshold value. analog-Inputs - This is the fourth threshold value. analo… |
| 1.3.6.1.4.1.994.3.4.7.18.1.33 | ColumnpSlot1Thresh5 | read-only | current | This field is used in the following card types: onboard-sensors - This is the maximum threshold value. analog-Inputs - This is the minimum threshold value. ana… |
| 1.3.6.1.4.1.994.3.4.7.18.1.44 | ColumnpSlot1ContactStyle | read-write | current | This field is used in the following card types: discrete-inputs - Determines the type of contact. |
| 1.3.6.1.4.1.994.3.4.7.18.1.46 | ColumnpSlot1Units | read-only | current | This field is used in the following card types: onboard-sensors - Description of the units of measurement. analog-Inputs - Description of the units of measurem… |
| 1.3.6.1.4.1.994.3.4.7.18.1.47 | ColumnpSlot1OutputMode | read-write | current | This field is used in the following card types: discrete-outputs - Defines the different ways a control point can be activated. |
| 1.3.6.1.4.1.994.3.4.7.18.1.48 | ColumnpSlot1OutputState | read-write | current | This field is used in the following card types: discrete-outputs - A value of 0 will open the control point. A value of 1 will close the control point. |
| 1.3.6.1.4.1.994.3.4.7.18.1.49 | ColumnpSlot1OutputAuto | read-write | current | This field is used in the following card types: discrete-outputs - When this control point is opened, this alarm point will change state to the on state. |
| 1.3.6.1.4.1.994.3.4.7.18.1.57 | ColumnpSlot1BaudRate | read-write | current | This field is used in the following card types: serial-ports - Baud rate of the serial port. |
| 1.3.6.1.4.1.994.3.4.7.18.1.58 | ColumnpSlot1DataBits | read-write | current | This field is used in the following card types: serial-ports - Number of data bit for the serial port. |
| 1.3.6.1.4.1.994.3.4.7.18.1.59 | ColumnpSlot1Parity | read-write | current | This field is used in the following card types: serial-ports - Parity of the serial port. |
| 1.3.6.1.4.1.994.3.4.7.18.1.60 | ColumnpSlot1StopBits | read-write | current | This field is used in the following card types: serial-ports - Number of stop bits for the serial port. |
| 1.3.6.1.4.1.994.3.4.7.18.1.61 | ColumnpSlot1Protocol | read-write | current | This field is used in the following card types: serial-ports - Protocol the serial port is speaking. |
| 1.3.6.1.4.1.994.3.4.7.18.1.62 | ColumnpSlot1SerialRTS | read-write | current | This field is used in the following card types: serial-ports - Request To Send (RTS) setting for the serial port. |
| 1.3.6.1.4.1.994.3.4.7.18.1.63 | ColumnpSlot1SerialCTS | read-write | current | This field is used in the following card types: serial-ports - Clear To Send (CTS) setting for the serial port. |
| 1.3.6.1.4.1.994.3.4.7.18.1.64 | ColumnpSlot1LiveDescription | read-only | current | This field is used in the following card types: discrete-inputs - The current description of the alarm state. onboard-sensors - The description of the current … |
| 1.3.6.1.4.1.994.3.4.7.18.1.65 | ColumnpSlot1LiveLevel | read-only | current | This field is used in the following card types: discrete-inputs - The current level of the alarm. onboard-sensors - The level of the current state of the onboa… |
| 1.3.6.1.4.1.994.3.4.7.18.1.66 | ColumnpSlot1LiveRaw | read-only | current | This field is used in the following card types: onboard-sensors - The current reading from the onboard sensor. This value will always be between the threshold … |
| 1.3.6.1.4.1.994.3.4.7.18.1.67 | ColumnpSlot1LiveTime | read-only | current | This field is used in the following card types: discrete-inputs - The time of the last change of state. onboard-sensors - The time of the last event. analog-In… |
| 1.3.6.1.4.1.994.3.4.7.18.1.68 | ColumnpSlot1Present | read-only | current | This field is used in the following card types: serial-ports - If set to true, the serial port exists. If set to false the serial port does not exist. |
| 1.3.6.1.4.1.994.3.4.7.18.1.71 | ColumnpSlot1OutputAutoPkg | read-write | current | This field is used in the following card types: discrete-outputs - When this control point is opened, this is the package that the alarm point is located. |
| 1.3.6.1.4.1.994.3.4.7.18.1.72 | ColumnpSlot1VoltageRange | read-only | current | This field is used in the following card types: onboard-sensors - The voltage range. analog-Inputs - The voltage range. analog-Sensors - The voltage range. |
| 1.3.6.1.4.1.994.3.4.7.18.1.73 | ColumnpSlot1IPPortNum | read-write | current | This field is used in the following card types: serial-ports - IP port number of the target device. |
| 1.3.6.1.4.1.994.3.4.7.18.1.75 | ColumnpSlot1IOFormat | read-only | current | This field is used in the following card types: discrete-inputs - The io format of discrete inputs. discrete-outputs - The io format of discrete outputs. seria… |
| 1.3.6.1.4.1.994.3.4.7.18.1.76 | ColumnpSlot1PortType | read-only | current | This field is used in the following card types: serial-ports - The type of serial port. |
| 1.3.6.1.4.1.994.3.4.7.18.1.116 | ColumnpSlot1TL1SID | read-write | current | This field is used in the following card types: discrete-inputs - discrete-outputs - onboard-sensors - analog-Inputs - analog-Sensors - |
| 1.3.6.1.4.1.994.3.4.7.18.1.117 | ColumnpSlot1TL1COND | read-write | current | This field is used in the following card types: discrete-inputs - discrete-outputs - onboard-sensors - analog-Inputs - analog-Sensors - |
| 1.3.6.1.4.1.994.3.4.7.18.1.118 | ColumnpSlot1TL1Eqpt | read-write | current | This field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors - |
| 1.3.6.1.4.1.994.3.4.7.18.1.119 | ColumnpSlot1TL1Env | read-write | current | This field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors - |
| 1.3.6.1.4.1.994.3.4.7.18.1.120 | ColumnpSlot1TL1Srveff | read-write | current | This field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors - |
| 1.3.6.1.4.1.994.3.4.7.18.1.121 | ColumnpSlot1TL1Locn | read-write | current | This field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors - |
| 1.3.6.1.4.1.994.3.4.7.18.1.122 | ColumnpSlot1TL1Dirn | read-write | current | This field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors - |
| 1.3.6.1.4.1.994.3.4.7.18.1.131 | ColumnpSlot1SensorType | read-only | current | This field is used in the following card types: onboard-sensors - The type of sensor. analog-Inputs - The type of sensor. analog-Sensors - The type of sensor. |
| 1.3.6.1.4.1.994.3.4.7.18.1.999 | ColumnpSlot1Index | read-only | current | Index. |
| 1.3.6.1.4.1.994.3.4.7.19 | TablepSlot2Table | not-accessible | current | Table for configuration of Slot2 |
| 1.3.6.1.4.1.994.3.4.7.19.1 | RowpSlot2Entry | not-accessible | current | Entry for configuration table of Slot2 |
| 1.3.6.1.4.1.994.3.4.7.19.1.3 | ColumnpSlot2Description | read-write | current | This field is used in the following card types: discrete-inputs - Description of the alarm point. discrete-outputs - Description of the control point. serial-p… |
| 1.3.6.1.4.1.994.3.4.7.19.1.4 | ColumnpSlot2Desc0 | read-write | current | This field is used in the following card types: discrete-inputs - Description of the off state. discrete-outputs - Description when the control point is open. … |
| 1.3.6.1.4.1.994.3.4.7.19.1.5 | ColumnpSlot2Desc1 | read-write | current | This field is used in the following card types: discrete-inputs - Description of the on state. discrete-outputs - Description when the control point is closed.… |
| 1.3.6.1.4.1.994.3.4.7.19.1.6 | ColumnpSlot2Desc2 | read-write | current | This field is used in the following card types: onboard-sensors - The description for values between threshold 2 and threshold 3. analog-Inputs - The descripti… |
| 1.3.6.1.4.1.994.3.4.7.19.1.7 | ColumnpSlot2Desc3 | read-write | current | This field is used in the following card types: onboard-sensors - The description for values between threshold 3 and threshold 4. analog-Inputs - The descripti… |
| 1.3.6.1.4.1.994.3.4.7.19.1.8 | ColumnpSlot2Desc4 | read-write | current | This field is used in the following card types: onboard-sensors - The description for values between threshold 4 and threshold 5. analog-Inputs - The descripti… |
| 1.3.6.1.4.1.994.3.4.7.19.1.9 | ColumnpSlot2Desc5 | read-write | current | This field is used in the following card types: analog-Inputs - Description for a communications failure to the sensor. analog-Sensors - Description for a comm… |
| 1.3.6.1.4.1.994.3.4.7.19.1.10 | ColumnpSlot2Configured | read-write | current | This field is used in the following card types: discrete-inputs - If set to true, changes of state will be reported. If set to false, not change of states will… |
| 1.3.6.1.4.1.994.3.4.7.19.1.11 | ColumnpSlot2SendEmail | read-write | current | This field is used in the following card types: discrete-inputs - If set to true, an email will be sent on a change of state. If false, no email will be sent. … |
| 1.3.6.1.4.1.994.3.4.7.19.1.12 | ColumnpSlot2SendSNMPTrap | read-write | current | This field is used in the following card types: discrete-inputs - If set to true, an SNMP trap will be sent on a change of state. If false, no SNMP trap will b… |
| 1.3.6.1.4.1.994.3.4.7.19.1.14 | ColumnpSlot2IpAddress | read-write | current | This field is used in the following card types: serial-ports - IP Address of the target device. |
| 1.3.6.1.4.1.994.3.4.7.19.1.17 | ColumnpSlot2Level0 | read-write | current | This field is used in the following card types: discrete-inputs - Level of the off state. discrete-outputs - Level of the control point when open. onboard-sens… |
| 1.3.6.1.4.1.994.3.4.7.19.1.18 | ColumnpSlot2Level1 | read-write | current | This field is used in the following card types: discrete-inputs - Level of the on state. discrete-outputs - Level of the control point when closed. onboard-sen… |
| 1.3.6.1.4.1.994.3.4.7.19.1.19 | ColumnpSlot2Level2 | read-write | current | This field is used in the following card types: onboard-sensors - The level for values between threshold 2 and threshold 3. analog-Inputs - The level for value… |
| 1.3.6.1.4.1.994.3.4.7.19.1.20 | ColumnpSlot2Level3 | read-write | current | This field is used in the following card types: onboard-sensors - The level for values between threshold 3 and threshold 4. analog-Inputs - The level for value… |
| 1.3.6.1.4.1.994.3.4.7.19.1.21 | ColumnpSlot2Level4 | read-write | current | This field is used in the following card types: onboard-sensors - The level for values between threshold 4 and threshold 5. analog-Inputs - The level for value… |
| 1.3.6.1.4.1.994.3.4.7.19.1.22 | ColumnpSlot2Level5 | read-write | current | This field is used in the following card types: analog-Inputs - Level of a communications failure to the sensor. analog-Sensors - Level of a communications fai… |
| 1.3.6.1.4.1.994.3.4.7.19.1.23 | ColumnpSlot2ReadPeriod | read-write | current | This field is used in the following card types: serial-ports - Inactivity timeout (in minutes). |
| 1.3.6.1.4.1.994.3.4.7.19.1.28 | ColumnpSlot2Thresh0 | read-only | current | This field is used in the following card types: onboard-sensors - This is the minimun analog value. analog-Inputs - This is the maximum analog value. analog-Se… |
| 1.3.6.1.4.1.994.3.4.7.19.1.29 | ColumnpSlot2Thresh1 | read-write | current | This field is used in the following card types: onboard-sensors - This is the first threshold value. analog-Inputs - This is the first threshold value. analog-… |
| 1.3.6.1.4.1.994.3.4.7.19.1.30 | ColumnpSlot2Thresh2 | read-write | current | This field is used in the following card types: onboard-sensors - This is the second threshold value. analog-Inputs - This is the second threshold value. analo… |
| 1.3.6.1.4.1.994.3.4.7.19.1.31 | ColumnpSlot2Thresh3 | read-write | current | This field is used in the following card types: onboard-sensors - This is the third threshold value. analog-Inputs - This is the third threshold value. analog-… |
| 1.3.6.1.4.1.994.3.4.7.19.1.32 | ColumnpSlot2Thresh4 | read-write | current | This field is used in the following card types: onboard-sensors - This is the fourth threshold value. analog-Inputs - This is the fourth threshold value. analo… |
| 1.3.6.1.4.1.994.3.4.7.19.1.33 | ColumnpSlot2Thresh5 | read-only | current | This field is used in the following card types: onboard-sensors - This is the maximum threshold value. analog-Inputs - This is the minimum threshold value. ana… |
| 1.3.6.1.4.1.994.3.4.7.19.1.44 | ColumnpSlot2ContactStyle | read-write | current | This field is used in the following card types: discrete-inputs - Determines the type of contact. |
| 1.3.6.1.4.1.994.3.4.7.19.1.46 | ColumnpSlot2Units | read-only | current | This field is used in the following card types: onboard-sensors - Description of the units of measurement. analog-Inputs - Description of the units of measurem… |
| 1.3.6.1.4.1.994.3.4.7.19.1.47 | ColumnpSlot2OutputMode | read-write | current | This field is used in the following card types: discrete-outputs - Defines the different ways a control point can be activated. |
| 1.3.6.1.4.1.994.3.4.7.19.1.48 | ColumnpSlot2OutputState | read-write | current | This field is used in the following card types: discrete-outputs - A value of 0 will open the control point. A value of 1 will close the control point. |
| 1.3.6.1.4.1.994.3.4.7.19.1.49 | ColumnpSlot2OutputAuto | read-write | current | This field is used in the following card types: discrete-outputs - When this control point is opened, this alarm point will change state to the on state. |
| 1.3.6.1.4.1.994.3.4.7.19.1.57 | ColumnpSlot2BaudRate | read-write | current | This field is used in the following card types: serial-ports - Baud rate of the serial port. |
| 1.3.6.1.4.1.994.3.4.7.19.1.58 | ColumnpSlot2DataBits | read-write | current | This field is used in the following card types: serial-ports - Number of data bit for the serial port. |
| 1.3.6.1.4.1.994.3.4.7.19.1.59 | ColumnpSlot2Parity | read-write | current | This field is used in the following card types: serial-ports - Parity of the serial port. |
| 1.3.6.1.4.1.994.3.4.7.19.1.60 | ColumnpSlot2StopBits | read-write | current | This field is used in the following card types: serial-ports - Number of stop bits for the serial port. |
| 1.3.6.1.4.1.994.3.4.7.19.1.61 | ColumnpSlot2Protocol | read-write | current | This field is used in the following card types: serial-ports - Protocol the serial port is speaking. |
| 1.3.6.1.4.1.994.3.4.7.19.1.62 | ColumnpSlot2SerialRTS | read-write | current | This field is used in the following card types: serial-ports - Request To Send (RTS) setting for the serial port. |
| 1.3.6.1.4.1.994.3.4.7.19.1.63 | ColumnpSlot2SerialCTS | read-write | current | This field is used in the following card types: serial-ports - Clear To Send (CTS) setting for the serial port. |
| 1.3.6.1.4.1.994.3.4.7.19.1.64 | ColumnpSlot2LiveDescription | read-only | current | This field is used in the following card types: discrete-inputs - The current description of the alarm state. onboard-sensors - The description of the current … |
| 1.3.6.1.4.1.994.3.4.7.19.1.65 | ColumnpSlot2LiveLevel | read-only | current | This field is used in the following card types: discrete-inputs - The current level of the alarm. onboard-sensors - The level of the current state of the onboa… |
| 1.3.6.1.4.1.994.3.4.7.19.1.66 | ColumnpSlot2LiveRaw | read-only | current | This field is used in the following card types: onboard-sensors - The current reading from the onboard sensor. This value will always be between the threshold … |
| 1.3.6.1.4.1.994.3.4.7.19.1.67 | ColumnpSlot2LiveTime | read-only | current | This field is used in the following card types: discrete-inputs - The time of the last change of state. onboard-sensors - The time of the last event. analog-In… |
| 1.3.6.1.4.1.994.3.4.7.19.1.68 | ColumnpSlot2Present | read-only | current | This field is used in the following card types: serial-ports - If set to true, the serial port exists. If set to false the serial port does not exist. |
| 1.3.6.1.4.1.994.3.4.7.19.1.71 | ColumnpSlot2OutputAutoPkg | read-write | current | This field is used in the following card types: discrete-outputs - When this control point is opened, this is the package that the alarm point is located. |
| 1.3.6.1.4.1.994.3.4.7.19.1.72 | ColumnpSlot2VoltageRange | read-only | current | This field is used in the following card types: onboard-sensors - The voltage range. analog-Inputs - The voltage range. analog-Sensors - The voltage range. |
| 1.3.6.1.4.1.994.3.4.7.19.1.73 | ColumnpSlot2IPPortNum | read-write | current | This field is used in the following card types: serial-ports - IP port number of the target device. |
| 1.3.6.1.4.1.994.3.4.7.19.1.75 | ColumnpSlot2IOFormat | read-only | current | This field is used in the following card types: discrete-inputs - The io format of discrete inputs. discrete-outputs - The io format of discrete outputs. seria… |
| 1.3.6.1.4.1.994.3.4.7.19.1.76 | ColumnpSlot2PortType | read-only | current | This field is used in the following card types: serial-ports - The type of serial port. |
| 1.3.6.1.4.1.994.3.4.7.19.1.116 | ColumnpSlot2TL1SID | read-write | current | This field is used in the following card types: discrete-inputs - discrete-outputs - onboard-sensors - analog-Inputs - analog-Sensors - |
| 1.3.6.1.4.1.994.3.4.7.19.1.117 | ColumnpSlot2TL1COND | read-write | current | This field is used in the following card types: discrete-inputs - discrete-outputs - onboard-sensors - analog-Inputs - analog-Sensors - |
| 1.3.6.1.4.1.994.3.4.7.19.1.118 | ColumnpSlot2TL1Eqpt | read-write | current | This field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors - |
| 1.3.6.1.4.1.994.3.4.7.19.1.119 | ColumnpSlot2TL1Env | read-write | current | This field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors - |
| 1.3.6.1.4.1.994.3.4.7.19.1.120 | ColumnpSlot2TL1Srveff | read-write | current | This field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors - |
| 1.3.6.1.4.1.994.3.4.7.19.1.121 | ColumnpSlot2TL1Locn | read-write | current | This field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors - |
| 1.3.6.1.4.1.994.3.4.7.19.1.122 | ColumnpSlot2TL1Dirn | read-write | current | This field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors - |
| 1.3.6.1.4.1.994.3.4.7.19.1.131 | ColumnpSlot2SensorType | read-only | current | This field is used in the following card types: onboard-sensors - The type of sensor. analog-Inputs - The type of sensor. analog-Sensors - The type of sensor. |
| 1.3.6.1.4.1.994.3.4.7.19.1.999 | ColumnpSlot2Index | read-only | current | Index. |
| 1.3.6.1.4.1.994.3.4.7.20 | TablepSlot3Table | not-accessible | current | Table for configuration of Slot3 |
| 1.3.6.1.4.1.994.3.4.7.20.1 | RowpSlot3Entry | not-accessible | current | Entry for configuration table of Slot3 |
| 1.3.6.1.4.1.994.3.4.7.20.1.3 | ColumnpSlot3Description | read-write | current | This field is used in the following card types: discrete-inputs - Description of the alarm point. discrete-outputs - Description of the control point. serial-p… |
| 1.3.6.1.4.1.994.3.4.7.20.1.4 | ColumnpSlot3Desc0 | read-write | current | This field is used in the following card types: discrete-inputs - Description of the off state. discrete-outputs - Description when the control point is open. … |
| 1.3.6.1.4.1.994.3.4.7.20.1.5 | ColumnpSlot3Desc1 | read-write | current | This field is used in the following card types: discrete-inputs - Description of the on state. discrete-outputs - Description when the control point is closed.… |
| 1.3.6.1.4.1.994.3.4.7.20.1.6 | ColumnpSlot3Desc2 | read-write | current | This field is used in the following card types: onboard-sensors - The description for values between threshold 2 and threshold 3. analog-Inputs - The descripti… |
| 1.3.6.1.4.1.994.3.4.7.20.1.7 | ColumnpSlot3Desc3 | read-write | current | This field is used in the following card types: onboard-sensors - The description for values between threshold 3 and threshold 4. analog-Inputs - The descripti… |
| 1.3.6.1.4.1.994.3.4.7.20.1.8 | ColumnpSlot3Desc4 | read-write | current | This field is used in the following card types: onboard-sensors - The description for values between threshold 4 and threshold 5. analog-Inputs - The descripti… |
| 1.3.6.1.4.1.994.3.4.7.20.1.9 | ColumnpSlot3Desc5 | read-write | current | This field is used in the following card types: analog-Inputs - Description for a communications failure to the sensor. analog-Sensors - Description for a comm… |
| 1.3.6.1.4.1.994.3.4.7.20.1.10 | ColumnpSlot3Configured | read-write | current | This field is used in the following card types: discrete-inputs - If set to true, changes of state will be reported. If set to false, not change of states will… |
| 1.3.6.1.4.1.994.3.4.7.20.1.11 | ColumnpSlot3SendEmail | read-write | current | This field is used in the following card types: discrete-inputs - If set to true, an email will be sent on a change of state. If false, no email will be sent. … |
| 1.3.6.1.4.1.994.3.4.7.20.1.12 | ColumnpSlot3SendSNMPTrap | read-write | current | This field is used in the following card types: discrete-inputs - If set to true, an SNMP trap will be sent on a change of state. If false, no SNMP trap will b… |
| 1.3.6.1.4.1.994.3.4.7.20.1.14 | ColumnpSlot3IpAddress | read-write | current | This field is used in the following card types: serial-ports - IP Address of the target device. |
| 1.3.6.1.4.1.994.3.4.7.20.1.17 | ColumnpSlot3Level0 | read-write | current | This field is used in the following card types: discrete-inputs - Level of the off state. discrete-outputs - Level of the control point when open. onboard-sens… |
| 1.3.6.1.4.1.994.3.4.7.20.1.18 | ColumnpSlot3Level1 | read-write | current | This field is used in the following card types: discrete-inputs - Level of the on state. discrete-outputs - Level of the control point when closed. onboard-sen… |
| 1.3.6.1.4.1.994.3.4.7.20.1.19 | ColumnpSlot3Level2 | read-write | current | This field is used in the following card types: onboard-sensors - The level for values between threshold 2 and threshold 3. analog-Inputs - The level for value… |
| 1.3.6.1.4.1.994.3.4.7.20.1.20 | ColumnpSlot3Level3 | read-write | current | This field is used in the following card types: onboard-sensors - The level for values between threshold 3 and threshold 4. analog-Inputs - The level for value… |
| 1.3.6.1.4.1.994.3.4.7.20.1.21 | ColumnpSlot3Level4 | read-write | current | This field is used in the following card types: onboard-sensors - The level for values between threshold 4 and threshold 5. analog-Inputs - The level for value… |
| 1.3.6.1.4.1.994.3.4.7.20.1.22 | ColumnpSlot3Level5 | read-write | current | This field is used in the following card types: analog-Inputs - Level of a communications failure to the sensor. analog-Sensors - Level of a communications fai… |
| 1.3.6.1.4.1.994.3.4.7.20.1.23 | ColumnpSlot3ReadPeriod | read-write | current | This field is used in the following card types: serial-ports - Inactivity timeout (in minutes). |
| 1.3.6.1.4.1.994.3.4.7.20.1.28 | ColumnpSlot3Thresh0 | read-only | current | This field is used in the following card types: onboard-sensors - This is the minimun analog value. analog-Inputs - This is the maximum analog value. analog-Se… |
| 1.3.6.1.4.1.994.3.4.7.20.1.29 | ColumnpSlot3Thresh1 | read-write | current | This field is used in the following card types: onboard-sensors - This is the first threshold value. analog-Inputs - This is the first threshold value. analog-… |
| 1.3.6.1.4.1.994.3.4.7.20.1.30 | ColumnpSlot3Thresh2 | read-write | current | This field is used in the following card types: onboard-sensors - This is the second threshold value. analog-Inputs - This is the second threshold value. analo… |
| 1.3.6.1.4.1.994.3.4.7.20.1.31 | ColumnpSlot3Thresh3 | read-write | current | This field is used in the following card types: onboard-sensors - This is the third threshold value. analog-Inputs - This is the third threshold value. analog-… |
| 1.3.6.1.4.1.994.3.4.7.20.1.32 | ColumnpSlot3Thresh4 | read-write | current | This field is used in the following card types: onboard-sensors - This is the fourth threshold value. analog-Inputs - This is the fourth threshold value. analo… |
| 1.3.6.1.4.1.994.3.4.7.20.1.33 | ColumnpSlot3Thresh5 | read-only | current | This field is used in the following card types: onboard-sensors - This is the maximum threshold value. analog-Inputs - This is the minimum threshold value. ana… |
| 1.3.6.1.4.1.994.3.4.7.20.1.44 | ColumnpSlot3ContactStyle | read-write | current | This field is used in the following card types: discrete-inputs - Determines the type of contact. |
| 1.3.6.1.4.1.994.3.4.7.20.1.46 | ColumnpSlot3Units | read-only | current | This field is used in the following card types: onboard-sensors - Description of the units of measurement. analog-Inputs - Description of the units of measurem… |
| 1.3.6.1.4.1.994.3.4.7.20.1.47 | ColumnpSlot3OutputMode | read-write | current | This field is used in the following card types: discrete-outputs - Defines the different ways a control point can be activated. |
| 1.3.6.1.4.1.994.3.4.7.20.1.48 | ColumnpSlot3OutputState | read-write | current | This field is used in the following card types: discrete-outputs - A value of 0 will open the control point. A value of 1 will close the control point. |
| 1.3.6.1.4.1.994.3.4.7.20.1.49 | ColumnpSlot3OutputAuto | read-write | current | This field is used in the following card types: discrete-outputs - When this control point is opened, this alarm point will change state to the on state. |
| 1.3.6.1.4.1.994.3.4.7.20.1.57 | ColumnpSlot3BaudRate | read-write | current | This field is used in the following card types: serial-ports - Baud rate of the serial port. |
| 1.3.6.1.4.1.994.3.4.7.20.1.58 | ColumnpSlot3DataBits | read-write | current | This field is used in the following card types: serial-ports - Number of data bit for the serial port. |
| 1.3.6.1.4.1.994.3.4.7.20.1.59 | ColumnpSlot3Parity | read-write | current | This field is used in the following card types: serial-ports - Parity of the serial port. |
| 1.3.6.1.4.1.994.3.4.7.20.1.60 | ColumnpSlot3StopBits | read-write | current | This field is used in the following card types: serial-ports - Number of stop bits for the serial port. |
| 1.3.6.1.4.1.994.3.4.7.20.1.61 | ColumnpSlot3Protocol | read-write | current | This field is used in the following card types: serial-ports - Protocol the serial port is speaking. |
| 1.3.6.1.4.1.994.3.4.7.20.1.62 | ColumnpSlot3SerialRTS | read-write | current | This field is used in the following card types: serial-ports - Request To Send (RTS) setting for the serial port. |
| 1.3.6.1.4.1.994.3.4.7.20.1.63 | ColumnpSlot3SerialCTS | read-write | current | This field is used in the following card types: serial-ports - Clear To Send (CTS) setting for the serial port. |
| 1.3.6.1.4.1.994.3.4.7.20.1.64 | ColumnpSlot3LiveDescription | read-only | current | This field is used in the following card types: discrete-inputs - The current description of the alarm state. onboard-sensors - The description of the current … |
| 1.3.6.1.4.1.994.3.4.7.20.1.65 | ColumnpSlot3LiveLevel | read-only | current | This field is used in the following card types: discrete-inputs - The current level of the alarm. onboard-sensors - The level of the current state of the onboa… |
| 1.3.6.1.4.1.994.3.4.7.20.1.66 | ColumnpSlot3LiveRaw | read-only | current | This field is used in the following card types: onboard-sensors - The current reading from the onboard sensor. This value will always be between the threshold … |
| 1.3.6.1.4.1.994.3.4.7.20.1.67 | ColumnpSlot3LiveTime | read-only | current | This field is used in the following card types: discrete-inputs - The time of the last change of state. onboard-sensors - The time of the last event. analog-In… |
| 1.3.6.1.4.1.994.3.4.7.20.1.68 | ColumnpSlot3Present | read-only | current | This field is used in the following card types: serial-ports - If set to true, the serial port exists. If set to false the serial port does not exist. |
| 1.3.6.1.4.1.994.3.4.7.20.1.71 | ColumnpSlot3OutputAutoPkg | read-write | current | This field is used in the following card types: discrete-outputs - When this control point is opened, this is the package that the alarm point is located. |
| 1.3.6.1.4.1.994.3.4.7.20.1.72 | ColumnpSlot3VoltageRange | read-only | current | This field is used in the following card types: onboard-sensors - The voltage range. analog-Inputs - The voltage range. analog-Sensors - The voltage range. |
| 1.3.6.1.4.1.994.3.4.7.20.1.73 | ColumnpSlot3IPPortNum | read-write | current | This field is used in the following card types: serial-ports - IP port number of the target device. |
| 1.3.6.1.4.1.994.3.4.7.20.1.75 | ColumnpSlot3IOFormat | read-only | current | This field is used in the following card types: discrete-inputs - The io format of discrete inputs. discrete-outputs - The io format of discrete outputs. seria… |
| 1.3.6.1.4.1.994.3.4.7.20.1.76 | ColumnpSlot3PortType | read-only | current | This field is used in the following card types: serial-ports - The type of serial port. |
| 1.3.6.1.4.1.994.3.4.7.20.1.116 | ColumnpSlot3TL1SID | read-write | current | This field is used in the following card types: discrete-inputs - discrete-outputs - onboard-sensors - analog-Inputs - analog-Sensors - |
| 1.3.6.1.4.1.994.3.4.7.20.1.117 | ColumnpSlot3TL1COND | read-write | current | This field is used in the following card types: discrete-inputs - discrete-outputs - onboard-sensors - analog-Inputs - analog-Sensors - |
| 1.3.6.1.4.1.994.3.4.7.20.1.118 | ColumnpSlot3TL1Eqpt | read-write | current | This field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors - |
| 1.3.6.1.4.1.994.3.4.7.20.1.119 | ColumnpSlot3TL1Env | read-write | current | This field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors - |
| 1.3.6.1.4.1.994.3.4.7.20.1.120 | ColumnpSlot3TL1Srveff | read-write | current | This field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors - |
| 1.3.6.1.4.1.994.3.4.7.20.1.121 | ColumnpSlot3TL1Locn | read-write | current | This field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors - |
| 1.3.6.1.4.1.994.3.4.7.20.1.122 | ColumnpSlot3TL1Dirn | read-write | current | This field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors - |
| 1.3.6.1.4.1.994.3.4.7.20.1.131 | ColumnpSlot3SensorType | read-only | current | This field is used in the following card types: onboard-sensors - The type of sensor. analog-Inputs - The type of sensor. analog-Sensors - The type of sensor. |
| 1.3.6.1.4.1.994.3.4.7.20.1.999 | ColumnpSlot3Index | read-only | current | Index. |
| 1.3.6.1.4.1.994.3.4.7.21 | TablepSlot4Table | not-accessible | current | Table for configuration of Slot4 |
| 1.3.6.1.4.1.994.3.4.7.21.1 | RowpSlot4Entry | not-accessible | current | Entry for configuration table of Slot4 |
| 1.3.6.1.4.1.994.3.4.7.21.1.3 | ColumnpSlot4Description | read-write | current | This field is used in the following card types: discrete-inputs - Description of the alarm point. discrete-outputs - Description of the control point. serial-p… |
| 1.3.6.1.4.1.994.3.4.7.21.1.4 | ColumnpSlot4Desc0 | read-write | current | This field is used in the following card types: discrete-inputs - Description of the off state. discrete-outputs - Description when the control point is open. … |
| 1.3.6.1.4.1.994.3.4.7.21.1.5 | ColumnpSlot4Desc1 | read-write | current | This field is used in the following card types: discrete-inputs - Description of the on state. discrete-outputs - Description when the control point is closed.… |
| 1.3.6.1.4.1.994.3.4.7.21.1.6 | ColumnpSlot4Desc2 | read-write | current | This field is used in the following card types: onboard-sensors - The description for values between threshold 2 and threshold 3. analog-Inputs - The descripti… |
| 1.3.6.1.4.1.994.3.4.7.21.1.7 | ColumnpSlot4Desc3 | read-write | current | This field is used in the following card types: onboard-sensors - The description for values between threshold 3 and threshold 4. analog-Inputs - The descripti… |
| 1.3.6.1.4.1.994.3.4.7.21.1.8 | ColumnpSlot4Desc4 | read-write | current | This field is used in the following card types: onboard-sensors - The description for values between threshold 4 and threshold 5. analog-Inputs - The descripti… |
| 1.3.6.1.4.1.994.3.4.7.21.1.9 | ColumnpSlot4Desc5 | read-write | current | This field is used in the following card types: analog-Inputs - Description for a communications failure to the sensor. analog-Sensors - Description for a comm… |
| 1.3.6.1.4.1.994.3.4.7.21.1.10 | ColumnpSlot4Configured | read-write | current | This field is used in the following card types: discrete-inputs - If set to true, changes of state will be reported. If set to false, not change of states will… |
| 1.3.6.1.4.1.994.3.4.7.21.1.11 | ColumnpSlot4SendEmail | read-write | current | This field is used in the following card types: discrete-inputs - If set to true, an email will be sent on a change of state. If false, no email will be sent. … |
| 1.3.6.1.4.1.994.3.4.7.21.1.12 | ColumnpSlot4SendSNMPTrap | read-write | current | This field is used in the following card types: discrete-inputs - If set to true, an SNMP trap will be sent on a change of state. If false, no SNMP trap will b… |
| 1.3.6.1.4.1.994.3.4.7.21.1.14 | ColumnpSlot4IpAddress | read-write | current | This field is used in the following card types: serial-ports - IP Address of the target device. |
| 1.3.6.1.4.1.994.3.4.7.21.1.17 | ColumnpSlot4Level0 | read-write | current | This field is used in the following card types: discrete-inputs - Level of the off state. discrete-outputs - Level of the control point when open. onboard-sens… |
| 1.3.6.1.4.1.994.3.4.7.21.1.18 | ColumnpSlot4Level1 | read-write | current | This field is used in the following card types: discrete-inputs - Level of the on state. discrete-outputs - Level of the control point when closed. onboard-sen… |
| 1.3.6.1.4.1.994.3.4.7.21.1.19 | ColumnpSlot4Level2 | read-write | current | This field is used in the following card types: onboard-sensors - The level for values between threshold 2 and threshold 3. analog-Inputs - The level for value… |
| 1.3.6.1.4.1.994.3.4.7.21.1.20 | ColumnpSlot4Level3 | read-write | current | This field is used in the following card types: onboard-sensors - The level for values between threshold 3 and threshold 4. analog-Inputs - The level for value… |
| 1.3.6.1.4.1.994.3.4.7.21.1.21 | ColumnpSlot4Level4 | read-write | current | This field is used in the following card types: onboard-sensors - The level for values between threshold 4 and threshold 5. analog-Inputs - The level for value… |
| 1.3.6.1.4.1.994.3.4.7.21.1.22 | ColumnpSlot4Level5 | read-write | current | This field is used in the following card types: analog-Inputs - Level of a communications failure to the sensor. analog-Sensors - Level of a communications fai… |
| 1.3.6.1.4.1.994.3.4.7.21.1.23 | ColumnpSlot4ReadPeriod | read-write | current | This field is used in the following card types: serial-ports - Inactivity timeout (in minutes). |
| 1.3.6.1.4.1.994.3.4.7.21.1.28 | ColumnpSlot4Thresh0 | read-only | current | This field is used in the following card types: onboard-sensors - This is the minimun analog value. analog-Inputs - This is the maximum analog value. analog-Se… |
| 1.3.6.1.4.1.994.3.4.7.21.1.29 | ColumnpSlot4Thresh1 | read-write | current | This field is used in the following card types: onboard-sensors - This is the first threshold value. analog-Inputs - This is the first threshold value. analog-… |
| 1.3.6.1.4.1.994.3.4.7.21.1.30 | ColumnpSlot4Thresh2 | read-write | current | This field is used in the following card types: onboard-sensors - This is the second threshold value. analog-Inputs - This is the second threshold value. analo… |
| 1.3.6.1.4.1.994.3.4.7.21.1.31 | ColumnpSlot4Thresh3 | read-write | current | This field is used in the following card types: onboard-sensors - This is the third threshold value. analog-Inputs - This is the third threshold value. analog-… |
| 1.3.6.1.4.1.994.3.4.7.21.1.32 | ColumnpSlot4Thresh4 | read-write | current | This field is used in the following card types: onboard-sensors - This is the fourth threshold value. analog-Inputs - This is the fourth threshold value. analo… |
| 1.3.6.1.4.1.994.3.4.7.21.1.33 | ColumnpSlot4Thresh5 | read-only | current | This field is used in the following card types: onboard-sensors - This is the maximum threshold value. analog-Inputs - This is the minimum threshold value. ana… |
| 1.3.6.1.4.1.994.3.4.7.21.1.44 | ColumnpSlot4ContactStyle | read-write | current | This field is used in the following card types: discrete-inputs - Determines the type of contact. |
| 1.3.6.1.4.1.994.3.4.7.21.1.46 | ColumnpSlot4Units | read-only | current | This field is used in the following card types: onboard-sensors - Description of the units of measurement. analog-Inputs - Description of the units of measurem… |
| 1.3.6.1.4.1.994.3.4.7.21.1.47 | ColumnpSlot4OutputMode | read-write | current | This field is used in the following card types: discrete-outputs - Defines the different ways a control point can be activated. |
| 1.3.6.1.4.1.994.3.4.7.21.1.48 | ColumnpSlot4OutputState | read-write | current | This field is used in the following card types: discrete-outputs - A value of 0 will open the control point. A value of 1 will close the control point. |
| 1.3.6.1.4.1.994.3.4.7.21.1.49 | ColumnpSlot4OutputAuto | read-write | current | This field is used in the following card types: discrete-outputs - When this control point is opened, this alarm point will change state to the on state. |
| 1.3.6.1.4.1.994.3.4.7.21.1.57 | ColumnpSlot4BaudRate | read-write | current | This field is used in the following card types: serial-ports - Baud rate of the serial port. |
| 1.3.6.1.4.1.994.3.4.7.21.1.58 | ColumnpSlot4DataBits | read-write | current | This field is used in the following card types: serial-ports - Number of data bit for the serial port. |
| 1.3.6.1.4.1.994.3.4.7.21.1.59 | ColumnpSlot4Parity | read-write | current | This field is used in the following card types: serial-ports - Parity of the serial port. |
| 1.3.6.1.4.1.994.3.4.7.21.1.60 | ColumnpSlot4StopBits | read-write | current | This field is used in the following card types: serial-ports - Number of stop bits for the serial port. |
| 1.3.6.1.4.1.994.3.4.7.21.1.61 | ColumnpSlot4Protocol | read-write | current | This field is used in the following card types: serial-ports - Protocol the serial port is speaking. |
| 1.3.6.1.4.1.994.3.4.7.21.1.62 | ColumnpSlot4SerialRTS | read-write | current | This field is used in the following card types: serial-ports - Request To Send (RTS) setting for the serial port. |
| 1.3.6.1.4.1.994.3.4.7.21.1.63 | ColumnpSlot4SerialCTS | read-write | current | This field is used in the following card types: serial-ports - Clear To Send (CTS) setting for the serial port. |
| 1.3.6.1.4.1.994.3.4.7.21.1.64 | ColumnpSlot4LiveDescription | read-only | current | This field is used in the following card types: discrete-inputs - The current description of the alarm state. onboard-sensors - The description of the current … |
| 1.3.6.1.4.1.994.3.4.7.21.1.65 | ColumnpSlot4LiveLevel | read-only | current | This field is used in the following card types: discrete-inputs - The current level of the alarm. onboard-sensors - The level of the current state of the onboa… |
| 1.3.6.1.4.1.994.3.4.7.21.1.66 | ColumnpSlot4LiveRaw | read-only | current | This field is used in the following card types: onboard-sensors - The current reading from the onboard sensor. This value will always be between the threshold … |
| 1.3.6.1.4.1.994.3.4.7.21.1.67 | ColumnpSlot4LiveTime | read-only | current | This field is used in the following card types: discrete-inputs - The time of the last change of state. onboard-sensors - The time of the last event. analog-In… |
| 1.3.6.1.4.1.994.3.4.7.21.1.68 | ColumnpSlot4Present | read-only | current | This field is used in the following card types: serial-ports - If set to true, the serial port exists. If set to false the serial port does not exist. |
| 1.3.6.1.4.1.994.3.4.7.21.1.71 | ColumnpSlot4OutputAutoPkg | read-write | current | This field is used in the following card types: discrete-outputs - When this control point is opened, this is the package that the alarm point is located. |
| 1.3.6.1.4.1.994.3.4.7.21.1.72 | ColumnpSlot4VoltageRange | read-only | current | This field is used in the following card types: onboard-sensors - The voltage range. analog-Inputs - The voltage range. analog-Sensors - The voltage range. |
| 1.3.6.1.4.1.994.3.4.7.21.1.73 | ColumnpSlot4IPPortNum | read-write | current | This field is used in the following card types: serial-ports - IP port number of the target device. |
| 1.3.6.1.4.1.994.3.4.7.21.1.75 | ColumnpSlot4IOFormat | read-only | current | This field is used in the following card types: discrete-inputs - The io format of discrete inputs. discrete-outputs - The io format of discrete outputs. seria… |
| 1.3.6.1.4.1.994.3.4.7.21.1.76 | ColumnpSlot4PortType | read-only | current | This field is used in the following card types: serial-ports - The type of serial port. |
| 1.3.6.1.4.1.994.3.4.7.21.1.116 | ColumnpSlot4TL1SID | read-write | current | This field is used in the following card types: discrete-inputs - discrete-outputs - onboard-sensors - analog-Inputs - analog-Sensors - |
| 1.3.6.1.4.1.994.3.4.7.21.1.117 | ColumnpSlot4TL1COND | read-write | current | This field is used in the following card types: discrete-inputs - discrete-outputs - onboard-sensors - analog-Inputs - analog-Sensors - |
| 1.3.6.1.4.1.994.3.4.7.21.1.118 | ColumnpSlot4TL1Eqpt | read-write | current | This field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors - |
| 1.3.6.1.4.1.994.3.4.7.21.1.119 | ColumnpSlot4TL1Env | read-write | current | This field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors - |
| 1.3.6.1.4.1.994.3.4.7.21.1.120 | ColumnpSlot4TL1Srveff | read-write | current | This field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors - |
| 1.3.6.1.4.1.994.3.4.7.21.1.121 | ColumnpSlot4TL1Locn | read-write | current | This field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors - |
| 1.3.6.1.4.1.994.3.4.7.21.1.122 | ColumnpSlot4TL1Dirn | read-write | current | This field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors - |
| 1.3.6.1.4.1.994.3.4.7.21.1.131 | ColumnpSlot4SensorType | read-only | current | This field is used in the following card types: onboard-sensors - The type of sensor. analog-Inputs - The type of sensor. analog-Sensors - The type of sensor. |
| 1.3.6.1.4.1.994.3.4.7.21.1.999 | ColumnpSlot4Index | read-only | current | Index. |
| 1.3.6.1.4.1.994.3.4.7.22 | TablepSlot5Table | not-accessible | current | Table for configuration of Slot5 |
| 1.3.6.1.4.1.994.3.4.7.22.1 | RowpSlot5Entry | not-accessible | current | Entry for configuration table of Slot5 |
| 1.3.6.1.4.1.994.3.4.7.22.1.3 | ColumnpSlot5Description | read-write | current | This field is used in the following card types: discrete-inputs - Description of the alarm point. discrete-outputs - Description of the control point. serial-p… |
| 1.3.6.1.4.1.994.3.4.7.22.1.4 | ColumnpSlot5Desc0 | read-write | current | This field is used in the following card types: discrete-inputs - Description of the off state. discrete-outputs - Description when the control point is open. … |
| 1.3.6.1.4.1.994.3.4.7.22.1.5 | ColumnpSlot5Desc1 | read-write | current | This field is used in the following card types: discrete-inputs - Description of the on state. discrete-outputs - Description when the control point is closed.… |
| 1.3.6.1.4.1.994.3.4.7.22.1.6 | ColumnpSlot5Desc2 | read-write | current | This field is used in the following card types: onboard-sensors - The description for values between threshold 2 and threshold 3. analog-Inputs - The descripti… |
| 1.3.6.1.4.1.994.3.4.7.22.1.7 | ColumnpSlot5Desc3 | read-write | current | This field is used in the following card types: onboard-sensors - The description for values between threshold 3 and threshold 4. analog-Inputs - The descripti… |
| 1.3.6.1.4.1.994.3.4.7.22.1.8 | ColumnpSlot5Desc4 | read-write | current | This field is used in the following card types: onboard-sensors - The description for values between threshold 4 and threshold 5. analog-Inputs - The descripti… |
| 1.3.6.1.4.1.994.3.4.7.22.1.9 | ColumnpSlot5Desc5 | read-write | current | This field is used in the following card types: analog-Inputs - Description for a communications failure to the sensor. analog-Sensors - Description for a comm… |
| 1.3.6.1.4.1.994.3.4.7.22.1.10 | ColumnpSlot5Configured | read-write | current | This field is used in the following card types: discrete-inputs - If set to true, changes of state will be reported. If set to false, not change of states will… |
| 1.3.6.1.4.1.994.3.4.7.22.1.11 | ColumnpSlot5SendEmail | read-write | current | This field is used in the following card types: discrete-inputs - If set to true, an email will be sent on a change of state. If false, no email will be sent. … |
| 1.3.6.1.4.1.994.3.4.7.22.1.12 | ColumnpSlot5SendSNMPTrap | read-write | current | This field is used in the following card types: discrete-inputs - If set to true, an SNMP trap will be sent on a change of state. If false, no SNMP trap will b… |
| 1.3.6.1.4.1.994.3.4.7.22.1.14 | ColumnpSlot5IpAddress | read-write | current | This field is used in the following card types: serial-ports - IP Address of the target device. |
| 1.3.6.1.4.1.994.3.4.7.22.1.17 | ColumnpSlot5Level0 | read-write | current | This field is used in the following card types: discrete-inputs - Level of the off state. discrete-outputs - Level of the control point when open. onboard-sens… |
| 1.3.6.1.4.1.994.3.4.7.22.1.18 | ColumnpSlot5Level1 | read-write | current | This field is used in the following card types: discrete-inputs - Level of the on state. discrete-outputs - Level of the control point when closed. onboard-sen… |
| 1.3.6.1.4.1.994.3.4.7.22.1.19 | ColumnpSlot5Level2 | read-write | current | This field is used in the following card types: onboard-sensors - The level for values between threshold 2 and threshold 3. analog-Inputs - The level for value… |
| 1.3.6.1.4.1.994.3.4.7.22.1.20 | ColumnpSlot5Level3 | read-write | current | This field is used in the following card types: onboard-sensors - The level for values between threshold 3 and threshold 4. analog-Inputs - The level for value… |
| 1.3.6.1.4.1.994.3.4.7.22.1.21 | ColumnpSlot5Level4 | read-write | current | This field is used in the following card types: onboard-sensors - The level for values between threshold 4 and threshold 5. analog-Inputs - The level for value… |
| 1.3.6.1.4.1.994.3.4.7.22.1.22 | ColumnpSlot5Level5 | read-write | current | This field is used in the following card types: analog-Inputs - Level of a communications failure to the sensor. analog-Sensors - Level of a communications fai… |
| 1.3.6.1.4.1.994.3.4.7.22.1.23 | ColumnpSlot5ReadPeriod | read-write | current | This field is used in the following card types: serial-ports - Inactivity timeout (in minutes). |
| 1.3.6.1.4.1.994.3.4.7.22.1.28 | ColumnpSlot5Thresh0 | read-only | current | This field is used in the following card types: onboard-sensors - This is the minimun analog value. analog-Inputs - This is the maximum analog value. analog-Se… |
| 1.3.6.1.4.1.994.3.4.7.22.1.29 | ColumnpSlot5Thresh1 | read-write | current | This field is used in the following card types: onboard-sensors - This is the first threshold value. analog-Inputs - This is the first threshold value. analog-… |
| 1.3.6.1.4.1.994.3.4.7.22.1.30 | ColumnpSlot5Thresh2 | read-write | current | This field is used in the following card types: onboard-sensors - This is the second threshold value. analog-Inputs - This is the second threshold value. analo… |
| 1.3.6.1.4.1.994.3.4.7.22.1.31 | ColumnpSlot5Thresh3 | read-write | current | This field is used in the following card types: onboard-sensors - This is the third threshold value. analog-Inputs - This is the third threshold value. analog-… |
| 1.3.6.1.4.1.994.3.4.7.22.1.32 | ColumnpSlot5Thresh4 | read-write | current | This field is used in the following card types: onboard-sensors - This is the fourth threshold value. analog-Inputs - This is the fourth threshold value. analo… |
| 1.3.6.1.4.1.994.3.4.7.22.1.33 | ColumnpSlot5Thresh5 | read-only | current | This field is used in the following card types: onboard-sensors - This is the maximum threshold value. analog-Inputs - This is the minimum threshold value. ana… |
| 1.3.6.1.4.1.994.3.4.7.22.1.44 | ColumnpSlot5ContactStyle | read-write | current | This field is used in the following card types: discrete-inputs - Determines the type of contact. |
| 1.3.6.1.4.1.994.3.4.7.22.1.46 | ColumnpSlot5Units | read-only | current | This field is used in the following card types: onboard-sensors - Description of the units of measurement. analog-Inputs - Description of the units of measurem… |
| 1.3.6.1.4.1.994.3.4.7.22.1.47 | ColumnpSlot5OutputMode | read-write | current | This field is used in the following card types: discrete-outputs - Defines the different ways a control point can be activated. |
| 1.3.6.1.4.1.994.3.4.7.22.1.48 | ColumnpSlot5OutputState | read-write | current | This field is used in the following card types: discrete-outputs - A value of 0 will open the control point. A value of 1 will close the control point. |
| 1.3.6.1.4.1.994.3.4.7.22.1.49 | ColumnpSlot5OutputAuto | read-write | current | This field is used in the following card types: discrete-outputs - When this control point is opened, this alarm point will change state to the on state. |
| 1.3.6.1.4.1.994.3.4.7.22.1.57 | ColumnpSlot5BaudRate | read-write | current | This field is used in the following card types: serial-ports - Baud rate of the serial port. |
| 1.3.6.1.4.1.994.3.4.7.22.1.58 | ColumnpSlot5DataBits | read-write | current | This field is used in the following card types: serial-ports - Number of data bit for the serial port. |
| 1.3.6.1.4.1.994.3.4.7.22.1.59 | ColumnpSlot5Parity | read-write | current | This field is used in the following card types: serial-ports - Parity of the serial port. |
| 1.3.6.1.4.1.994.3.4.7.22.1.60 | ColumnpSlot5StopBits | read-write | current | This field is used in the following card types: serial-ports - Number of stop bits for the serial port. |
| 1.3.6.1.4.1.994.3.4.7.22.1.61 | ColumnpSlot5Protocol | read-write | current | This field is used in the following card types: serial-ports - Protocol the serial port is speaking. |
| 1.3.6.1.4.1.994.3.4.7.22.1.62 | ColumnpSlot5SerialRTS | read-write | current | This field is used in the following card types: serial-ports - Request To Send (RTS) setting for the serial port. |
| 1.3.6.1.4.1.994.3.4.7.22.1.63 | ColumnpSlot5SerialCTS | read-write | current | This field is used in the following card types: serial-ports - Clear To Send (CTS) setting for the serial port. |
| 1.3.6.1.4.1.994.3.4.7.22.1.64 | ColumnpSlot5LiveDescription | read-only | current | This field is used in the following card types: discrete-inputs - The current description of the alarm state. onboard-sensors - The description of the current … |
| 1.3.6.1.4.1.994.3.4.7.22.1.65 | ColumnpSlot5LiveLevel | read-only | current | This field is used in the following card types: discrete-inputs - The current level of the alarm. onboard-sensors - The level of the current state of the onboa… |
| 1.3.6.1.4.1.994.3.4.7.22.1.66 | ColumnpSlot5LiveRaw | read-only | current | This field is used in the following card types: onboard-sensors - The current reading from the onboard sensor. This value will always be between the threshold … |
| 1.3.6.1.4.1.994.3.4.7.22.1.67 | ColumnpSlot5LiveTime | read-only | current | This field is used in the following card types: discrete-inputs - The time of the last change of state. onboard-sensors - The time of the last event. analog-In… |
| 1.3.6.1.4.1.994.3.4.7.22.1.68 | ColumnpSlot5Present | read-only | current | This field is used in the following card types: serial-ports - If set to true, the serial port exists. If set to false the serial port does not exist. |
| 1.3.6.1.4.1.994.3.4.7.22.1.71 | ColumnpSlot5OutputAutoPkg | read-write | current | This field is used in the following card types: discrete-outputs - When this control point is opened, this is the package that the alarm point is located. |
| 1.3.6.1.4.1.994.3.4.7.22.1.72 | ColumnpSlot5VoltageRange | read-only | current | This field is used in the following card types: onboard-sensors - The voltage range. analog-Inputs - The voltage range. analog-Sensors - The voltage range. |
| 1.3.6.1.4.1.994.3.4.7.22.1.73 | ColumnpSlot5IPPortNum | read-write | current | This field is used in the following card types: serial-ports - IP port number of the target device. |
| 1.3.6.1.4.1.994.3.4.7.22.1.75 | ColumnpSlot5IOFormat | read-only | current | This field is used in the following card types: discrete-inputs - The io format of discrete inputs. discrete-outputs - The io format of discrete outputs. seria… |
| 1.3.6.1.4.1.994.3.4.7.22.1.76 | ColumnpSlot5PortType | read-only | current | This field is used in the following card types: serial-ports - The type of serial port. |
| 1.3.6.1.4.1.994.3.4.7.22.1.116 | ColumnpSlot5TL1SID | read-write | current | This field is used in the following card types: discrete-inputs - discrete-outputs - onboard-sensors - analog-Inputs - analog-Sensors - |
| 1.3.6.1.4.1.994.3.4.7.22.1.117 | ColumnpSlot5TL1COND | read-write | current | This field is used in the following card types: discrete-inputs - discrete-outputs - onboard-sensors - analog-Inputs - analog-Sensors - |
| 1.3.6.1.4.1.994.3.4.7.22.1.118 | ColumnpSlot5TL1Eqpt | read-write | current | This field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors - |
| 1.3.6.1.4.1.994.3.4.7.22.1.119 | ColumnpSlot5TL1Env | read-write | current | This field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors - |
| 1.3.6.1.4.1.994.3.4.7.22.1.120 | ColumnpSlot5TL1Srveff | read-write | current | This field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors - |
| 1.3.6.1.4.1.994.3.4.7.22.1.121 | ColumnpSlot5TL1Locn | read-write | current | This field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors - |
| 1.3.6.1.4.1.994.3.4.7.22.1.122 | ColumnpSlot5TL1Dirn | read-write | current | This field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors - |
| 1.3.6.1.4.1.994.3.4.7.22.1.131 | ColumnpSlot5SensorType | read-only | current | This field is used in the following card types: onboard-sensors - The type of sensor. analog-Inputs - The type of sensor. analog-Sensors - The type of sensor. |
| 1.3.6.1.4.1.994.3.4.7.22.1.999 | ColumnpSlot5Index | read-only | current | Index. |
| 1.3.6.1.4.1.994.3.4.7.23 | TablepSlot6Table | not-accessible | current | Table for configuration of Slot6 |
| 1.3.6.1.4.1.994.3.4.7.23.1 | RowpSlot6Entry | not-accessible | current | Entry for configuration table of Slot6 |
| 1.3.6.1.4.1.994.3.4.7.23.1.3 | ColumnpSlot6Description | read-write | current | This field is used in the following card types: discrete-inputs - Description of the alarm point. discrete-outputs - Description of the control point. serial-p… |
| 1.3.6.1.4.1.994.3.4.7.23.1.4 | ColumnpSlot6Desc0 | read-write | current | This field is used in the following card types: discrete-inputs - Description of the off state. discrete-outputs - Description when the control point is open. … |
| 1.3.6.1.4.1.994.3.4.7.23.1.5 | ColumnpSlot6Desc1 | read-write | current | This field is used in the following card types: discrete-inputs - Description of the on state. discrete-outputs - Description when the control point is closed.… |
| 1.3.6.1.4.1.994.3.4.7.23.1.6 | ColumnpSlot6Desc2 | read-write | current | This field is used in the following card types: onboard-sensors - The description for values between threshold 2 and threshold 3. analog-Inputs - The descripti… |
| 1.3.6.1.4.1.994.3.4.7.23.1.7 | ColumnpSlot6Desc3 | read-write | current | This field is used in the following card types: onboard-sensors - The description for values between threshold 3 and threshold 4. analog-Inputs - The descripti… |
| 1.3.6.1.4.1.994.3.4.7.23.1.8 | ColumnpSlot6Desc4 | read-write | current | This field is used in the following card types: onboard-sensors - The description for values between threshold 4 and threshold 5. analog-Inputs - The descripti… |
| 1.3.6.1.4.1.994.3.4.7.23.1.9 | ColumnpSlot6Desc5 | read-write | current | This field is used in the following card types: analog-Inputs - Description for a communications failure to the sensor. analog-Sensors - Description for a comm… |
| 1.3.6.1.4.1.994.3.4.7.23.1.10 | ColumnpSlot6Configured | read-write | current | This field is used in the following card types: discrete-inputs - If set to true, changes of state will be reported. If set to false, not change of states will… |
| 1.3.6.1.4.1.994.3.4.7.23.1.11 | ColumnpSlot6SendEmail | read-write | current | This field is used in the following card types: discrete-inputs - If set to true, an email will be sent on a change of state. If false, no email will be sent. … |
| 1.3.6.1.4.1.994.3.4.7.23.1.12 | ColumnpSlot6SendSNMPTrap | read-write | current | This field is used in the following card types: discrete-inputs - If set to true, an SNMP trap will be sent on a change of state. If false, no SNMP trap will b… |
| 1.3.6.1.4.1.994.3.4.7.23.1.14 | ColumnpSlot6IpAddress | read-write | current | This field is used in the following card types: serial-ports - IP Address of the target device. |
| 1.3.6.1.4.1.994.3.4.7.23.1.17 | ColumnpSlot6Level0 | read-write | current | This field is used in the following card types: discrete-inputs - Level of the off state. discrete-outputs - Level of the control point when open. onboard-sens… |
| 1.3.6.1.4.1.994.3.4.7.23.1.18 | ColumnpSlot6Level1 | read-write | current | This field is used in the following card types: discrete-inputs - Level of the on state. discrete-outputs - Level of the control point when closed. onboard-sen… |
| 1.3.6.1.4.1.994.3.4.7.23.1.19 | ColumnpSlot6Level2 | read-write | current | This field is used in the following card types: onboard-sensors - The level for values between threshold 2 and threshold 3. analog-Inputs - The level for value… |
| 1.3.6.1.4.1.994.3.4.7.23.1.20 | ColumnpSlot6Level3 | read-write | current | This field is used in the following card types: onboard-sensors - The level for values between threshold 3 and threshold 4. analog-Inputs - The level for value… |
| 1.3.6.1.4.1.994.3.4.7.23.1.21 | ColumnpSlot6Level4 | read-write | current | This field is used in the following card types: onboard-sensors - The level for values between threshold 4 and threshold 5. analog-Inputs - The level for value… |
| 1.3.6.1.4.1.994.3.4.7.23.1.22 | ColumnpSlot6Level5 | read-write | current | This field is used in the following card types: analog-Inputs - Level of a communications failure to the sensor. analog-Sensors - Level of a communications fai… |
| 1.3.6.1.4.1.994.3.4.7.23.1.23 | ColumnpSlot6ReadPeriod | read-write | current | This field is used in the following card types: serial-ports - Inactivity timeout (in minutes). |
| 1.3.6.1.4.1.994.3.4.7.23.1.28 | ColumnpSlot6Thresh0 | read-only | current | This field is used in the following card types: onboard-sensors - This is the minimun analog value. analog-Inputs - This is the maximum analog value. analog-Se… |
| 1.3.6.1.4.1.994.3.4.7.23.1.29 | ColumnpSlot6Thresh1 | read-write | current | This field is used in the following card types: onboard-sensors - This is the first threshold value. analog-Inputs - This is the first threshold value. analog-… |
| 1.3.6.1.4.1.994.3.4.7.23.1.30 | ColumnpSlot6Thresh2 | read-write | current | This field is used in the following card types: onboard-sensors - This is the second threshold value. analog-Inputs - This is the second threshold value. analo… |
| 1.3.6.1.4.1.994.3.4.7.23.1.31 | ColumnpSlot6Thresh3 | read-write | current | This field is used in the following card types: onboard-sensors - This is the third threshold value. analog-Inputs - This is the third threshold value. analog-… |
| 1.3.6.1.4.1.994.3.4.7.23.1.32 | ColumnpSlot6Thresh4 | read-write | current | This field is used in the following card types: onboard-sensors - This is the fourth threshold value. analog-Inputs - This is the fourth threshold value. analo… |
| 1.3.6.1.4.1.994.3.4.7.23.1.33 | ColumnpSlot6Thresh5 | read-only | current | This field is used in the following card types: onboard-sensors - This is the maximum threshold value. analog-Inputs - This is the minimum threshold value. ana… |
| 1.3.6.1.4.1.994.3.4.7.23.1.44 | ColumnpSlot6ContactStyle | read-write | current | This field is used in the following card types: discrete-inputs - Determines the type of contact. |
| 1.3.6.1.4.1.994.3.4.7.23.1.46 | ColumnpSlot6Units | read-only | current | This field is used in the following card types: onboard-sensors - Description of the units of measurement. analog-Inputs - Description of the units of measurem… |
| 1.3.6.1.4.1.994.3.4.7.23.1.47 | ColumnpSlot6OutputMode | read-write | current | This field is used in the following card types: discrete-outputs - Defines the different ways a control point can be activated. |
| 1.3.6.1.4.1.994.3.4.7.23.1.48 | ColumnpSlot6OutputState | read-write | current | This field is used in the following card types: discrete-outputs - A value of 0 will open the control point. A value of 1 will close the control point. |
| 1.3.6.1.4.1.994.3.4.7.23.1.49 | ColumnpSlot6OutputAuto | read-write | current | This field is used in the following card types: discrete-outputs - When this control point is opened, this alarm point will change state to the on state. |
| 1.3.6.1.4.1.994.3.4.7.23.1.57 | ColumnpSlot6BaudRate | read-write | current | This field is used in the following card types: serial-ports - Baud rate of the serial port. |
| 1.3.6.1.4.1.994.3.4.7.23.1.58 | ColumnpSlot6DataBits | read-write | current | This field is used in the following card types: serial-ports - Number of data bit for the serial port. |
| 1.3.6.1.4.1.994.3.4.7.23.1.59 | ColumnpSlot6Parity | read-write | current | This field is used in the following card types: serial-ports - Parity of the serial port. |
| 1.3.6.1.4.1.994.3.4.7.23.1.60 | ColumnpSlot6StopBits | read-write | current | This field is used in the following card types: serial-ports - Number of stop bits for the serial port. |
| 1.3.6.1.4.1.994.3.4.7.23.1.61 | ColumnpSlot6Protocol | read-write | current | This field is used in the following card types: serial-ports - Protocol the serial port is speaking. |
| 1.3.6.1.4.1.994.3.4.7.23.1.62 | ColumnpSlot6SerialRTS | read-write | current | This field is used in the following card types: serial-ports - Request To Send (RTS) setting for the serial port. |
| 1.3.6.1.4.1.994.3.4.7.23.1.63 | ColumnpSlot6SerialCTS | read-write | current | This field is used in the following card types: serial-ports - Clear To Send (CTS) setting for the serial port. |
| 1.3.6.1.4.1.994.3.4.7.23.1.64 | ColumnpSlot6LiveDescription | read-only | current | This field is used in the following card types: discrete-inputs - The current description of the alarm state. onboard-sensors - The description of the current … |
| 1.3.6.1.4.1.994.3.4.7.23.1.65 | ColumnpSlot6LiveLevel | read-only | current | This field is used in the following card types: discrete-inputs - The current level of the alarm. onboard-sensors - The level of the current state of the onboa… |
| 1.3.6.1.4.1.994.3.4.7.23.1.66 | ColumnpSlot6LiveRaw | read-only | current | This field is used in the following card types: onboard-sensors - The current reading from the onboard sensor. This value will always be between the threshold … |
| 1.3.6.1.4.1.994.3.4.7.23.1.67 | ColumnpSlot6LiveTime | read-only | current | This field is used in the following card types: discrete-inputs - The time of the last change of state. onboard-sensors - The time of the last event. analog-In… |
| 1.3.6.1.4.1.994.3.4.7.23.1.68 | ColumnpSlot6Present | read-only | current | This field is used in the following card types: serial-ports - If set to true, the serial port exists. If set to false the serial port does not exist. |
| 1.3.6.1.4.1.994.3.4.7.23.1.71 | ColumnpSlot6OutputAutoPkg | read-write | current | This field is used in the following card types: discrete-outputs - When this control point is opened, this is the package that the alarm point is located. |
| 1.3.6.1.4.1.994.3.4.7.23.1.72 | ColumnpSlot6VoltageRange | read-only | current | This field is used in the following card types: onboard-sensors - The voltage range. analog-Inputs - The voltage range. analog-Sensors - The voltage range. |
| 1.3.6.1.4.1.994.3.4.7.23.1.73 | ColumnpSlot6IPPortNum | read-write | current | This field is used in the following card types: serial-ports - IP port number of the target device. |
| 1.3.6.1.4.1.994.3.4.7.23.1.75 | ColumnpSlot6IOFormat | read-only | current | This field is used in the following card types: discrete-inputs - The io format of discrete inputs. discrete-outputs - The io format of discrete outputs. seria… |
| 1.3.6.1.4.1.994.3.4.7.23.1.76 | ColumnpSlot6PortType | read-only | current | This field is used in the following card types: serial-ports - The type of serial port. |
| 1.3.6.1.4.1.994.3.4.7.23.1.116 | ColumnpSlot6TL1SID | read-write | current | This field is used in the following card types: discrete-inputs - discrete-outputs - onboard-sensors - analog-Inputs - analog-Sensors - |
| 1.3.6.1.4.1.994.3.4.7.23.1.117 | ColumnpSlot6TL1COND | read-write | current | This field is used in the following card types: discrete-inputs - discrete-outputs - onboard-sensors - analog-Inputs - analog-Sensors - |
| 1.3.6.1.4.1.994.3.4.7.23.1.118 | ColumnpSlot6TL1Eqpt | read-write | current | This field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors - |
| 1.3.6.1.4.1.994.3.4.7.23.1.119 | ColumnpSlot6TL1Env | read-write | current | This field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors - |
| 1.3.6.1.4.1.994.3.4.7.23.1.120 | ColumnpSlot6TL1Srveff | read-write | current | This field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors - |
| 1.3.6.1.4.1.994.3.4.7.23.1.121 | ColumnpSlot6TL1Locn | read-write | current | This field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors - |
| 1.3.6.1.4.1.994.3.4.7.23.1.122 | ColumnpSlot6TL1Dirn | read-write | current | This field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors - |
| 1.3.6.1.4.1.994.3.4.7.23.1.131 | ColumnpSlot6SensorType | read-only | current | This field is used in the following card types: onboard-sensors - The type of sensor. analog-Inputs - The type of sensor. analog-Sensors - The type of sensor. |
| 1.3.6.1.4.1.994.3.4.7.23.1.999 | ColumnpSlot6Index | read-only | current | Index. |
| 1.3.6.1.4.1.994.3.4.7.24 | TablepNetPortsTable | not-accessible | current | Table for configuration of NetPorts |
| 1.3.6.1.4.1.994.3.4.7.24.1 | RowpNetPortsEntry | not-accessible | current | Entry for configuration table of NetPorts |
| 1.3.6.1.4.1.994.3.4.7.24.1.3 | ColumnpNetPortsDescription | read-only | current | Description of the static network ports. |
| 1.3.6.1.4.1.994.3.4.7.24.1.23 | ColumnpNetPortsReadPeriod | read-write | current | Inactivity timeout (in minutes). |
| 1.3.6.1.4.1.994.3.4.7.24.1.73 | ColumnpNetPortsIPPortNum | read-write | current | IP port number to use when connecting to this network port. |
| 1.3.6.1.4.1.994.3.4.7.24.1.999 | ColumnpNetPortsIndex | read-only | current | Index. |
| 1.3.6.1.4.1.994.3.4.7.25 | NodewirelessModem | |||
| 1.3.6.1.4.1.994.3.4.7.25.78 | ScalarwirelessModemBackupIPAddress | read-only | current | Wireless Modem IP Address. |
| 1.3.6.1.4.1.994.3.4.7.25.81 | ScalarwirelessModemTime | read-write | current | Wireless modem 24 hour reset time (hh:mm:ss) |
| 1.3.6.1.4.1.994.3.4.7.25.96 | ScalarwirelessModemTransmit | read-write | current | The string that will be sent to the modem. |
| 1.3.6.1.4.1.994.3.4.7.25.97 | ScalarwirelessModemUseWirelessNetwork | read-write | current | Determines if modem tries to connect to wireless network. |
| 1.3.6.1.4.1.994.3.4.7.25.98 | ScalarwirelessModemUseResetTime | read-write | current | Determines if the modem resets at reset time. |
| 1.3.6.1.4.1.994.3.4.7.25.99 | ScalarwirelessModemResponseWaitTime | read-write | current | Response Timeout (s) |
| 1.3.6.1.4.1.994.3.4.7.25.115 | ScalarwirelessModemSecondary | read-write | current | Determines if the modem can use accept a dynamic (local) IP. |
| 1.3.6.1.4.1.994.3.4.7.26 | NodewebmonSecurity | |||
| 1.3.6.1.4.1.994.3.4.7.26.55 | ScalarwebmonSecurityUserLevel | read-write | current | This is the default user level. Anyone who has access to this device will have these permissions without logging in. One of the following masks from each group… |
| 1.3.6.1.4.1.994.3.4.7.26.77 | ScalarwebmonSecurityUnsecured | read-write | current | Allow unsecured configuration for SNMP. |
| 1.3.6.1.4.1.994.3.4.7.27 | NodedateTime | |||
| 1.3.6.1.4.1.994.3.4.7.27.10 | ScalardateTimeConfigured | read-write | current | Determines whether or not NTP will be used to set system time. |
| 1.3.6.1.4.1.994.3.4.7.27.14 | ScalardateTimeIpAddress | read-write | current | Time Server IP Address |
| 1.3.6.1.4.1.994.3.4.7.27.53 | ScalardateTimeDaylightSaving | read-write | current | Determines if Daylight Savings is automatically adjusted. |
| 1.3.6.1.4.1.994.3.4.7.27.80 | ScalardateTimeDate | read-write | current | This is the system date. |
| 1.3.6.1.4.1.994.3.4.7.27.81 | ScalardateTimeTime | read-write | current | This is the system time. |
| 1.3.6.1.4.1.994.3.4.7.27.88 | ScalardateTimeNegOffset | read-write | current | True if a negative offset from UTC is desired |
| 1.3.6.1.4.1.994.3.4.7.27.89 | ScalardateTimeUTCOffset | read-write | current | Time offset of local time compared to UTC |
| 1.3.6.1.4.1.994.3.4.7.28 | TablepDCMProtocolTable | not-accessible | current | Table for configuration of DCMProtocol |
| 1.3.6.1.4.1.994.3.4.7.28.1 | RowpDCMProtocolEntry | not-accessible | current | Entry for configuration table of DCMProtocol |
| 1.3.6.1.4.1.994.3.4.7.28.1.3 | ColumnpDCMProtocolDescription | read-only | current | Description of the input device that DCM will poll. |
| 1.3.6.1.4.1.994.3.4.7.28.1.10 | ColumnpDCMProtocolConfigured | read-write | current | If set to true, this input will be polled in DCM. If set to false, it will not be polled. |
| 1.3.6.1.4.1.994.3.4.7.28.1.83 | ColumnpDCMProtocolBaseDCMAddress | read-write | current | Base DCM address for this input device. |
| 1.3.6.1.4.1.994.3.4.7.28.1.999 | ColumnpDCMProtocolIndex | read-only | current | Index. |
| 1.3.6.1.4.1.994.3.4.7.29 | TablepdialOutTable | not-accessible | current | Table for configuration of dialOut |
| 1.3.6.1.4.1.994.3.4.7.29.1 | RowpdialOutEntry | not-accessible | current | Entry for configuration table of dialOut |
| 1.3.6.1.4.1.994.3.4.7.29.1.10 | ColumnpdialOutConfigured | read-write | current | Determines whether or not dial ou will be used to send SNMP traps. |
| 1.3.6.1.4.1.994.3.4.7.29.1.25 | ColumnpdialOutName | read-write | current | Dial out Username |
| 1.3.6.1.4.1.994.3.4.7.29.1.26 | ColumnpdialOutPassword | read-write | current | Password to use when dialing out |
| 1.3.6.1.4.1.994.3.4.7.29.1.79 | ColumnpdialOutDialOutNumber | read-write | current | Number to dial for dial out |
| 1.3.6.1.4.1.994.3.4.7.29.1.999 | ColumnpdialOutIndex | read-only | current | Index. |
| 1.3.6.1.4.1.994.3.4.7.30 | TablepderivedDiscreteTable | not-accessible | current | Table for configuration of derivedDiscrete |
| 1.3.6.1.4.1.994.3.4.7.30.1 | RowpderivedDiscreteEntry | not-accessible | current | Entry for configuration table of derivedDiscrete |
| 1.3.6.1.4.1.994.3.4.7.30.1.3 | ColumnpderivedDiscreteDescription | read-write | current | Description of the derived alarm point. |
| 1.3.6.1.4.1.994.3.4.7.30.1.4 | ColumnpderivedDiscreteDesc0 | read-write | current | Description of the off state. |
| 1.3.6.1.4.1.994.3.4.7.30.1.5 | ColumnpderivedDiscreteDesc1 | read-write | current | Description of the on state. |
| 1.3.6.1.4.1.994.3.4.7.30.1.10 | ColumnpderivedDiscreteConfigured | read-write | current | If set to true, changes of state will be reported. If set to false, not change of states will be reported. |
| 1.3.6.1.4.1.994.3.4.7.30.1.11 | ColumnpderivedDiscreteSendEmail | read-write | current | If set to true, an email will be sent on a change of state. If false, no email will be sent. |
| 1.3.6.1.4.1.994.3.4.7.30.1.12 | ColumnpderivedDiscreteSendSNMPTrap | read-write | current | If set to true, an SNMP trap will be sent on a change of state. If false, no SNMP trap will be sent. |
| 1.3.6.1.4.1.994.3.4.7.30.1.17 | ColumnpderivedDiscreteLevel0 | read-write | current | Level of the off state. |
| 1.3.6.1.4.1.994.3.4.7.30.1.18 | ColumnpderivedDiscreteLevel1 | read-write | current | Level of the on state. |
| 1.3.6.1.4.1.994.3.4.7.30.1.64 | ColumnpderivedDiscreteLiveDescription | read-only | current | The current description of the alarm state. |
| 1.3.6.1.4.1.994.3.4.7.30.1.65 | ColumnpderivedDiscreteLiveLevel | read-only | current | The current level of the alarm. |
| 1.3.6.1.4.1.994.3.4.7.30.1.67 | ColumnpderivedDiscreteLiveTime | read-only | current | The time of the last change of state. |
| 1.3.6.1.4.1.994.3.4.7.30.1.90 | ColumnpderivedDiscreteElementAPkg | read-write | current | Package where the alarm point is located for element A. |
| 1.3.6.1.4.1.994.3.4.7.30.1.91 | ColumnpderivedDiscreteElementAPoint | read-write | current | Alarm point for element A. |
| 1.3.6.1.4.1.994.3.4.7.30.1.92 | ColumnpderivedDiscreteElementBPkg | read-write | current | Package where the alarm point is located for element B. |
| 1.3.6.1.4.1.994.3.4.7.30.1.93 | ColumnpderivedDiscreteElementBPoint | read-write | current | Alarm point for element B. |
| 1.3.6.1.4.1.994.3.4.7.30.1.94 | ColumnpderivedDiscreteDiscreteFormula | read-write | current | The formula that will be used to compute the derived alarm. |
| 1.3.6.1.4.1.994.3.4.7.30.1.116 | ColumnpderivedDiscreteTL1SID | read-write | current | (TL1) System ID associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.30.1.117 | ColumnpderivedDiscreteTL1COND | read-write | current | (TL1) Condition text associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.30.1.118 | ColumnpderivedDiscreteTL1Eqpt | read-write | current | (TL1) EQPT field associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.30.1.119 | ColumnpderivedDiscreteTL1Env | read-write | current | (TL1) Environmental field associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.30.1.120 | ColumnpderivedDiscreteTL1Srveff | read-write | current | (TL1) Service Effecting field associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.30.1.121 | ColumnpderivedDiscreteTL1Locn | read-write | current | (TL1) Location field associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.30.1.122 | ColumnpderivedDiscreteTL1Dirn | read-write | current | (TL1) Direction field associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.30.1.999 | ColumnpderivedDiscreteIndex | read-only | current | Index. |
| 1.3.6.1.4.1.994.3.4.7.31 | Nodelicense | |||
| 1.3.6.1.4.1.994.3.4.7.31.3 | ScalarlicenseDescription | read-only | current | This describes the status of the license |
| 1.3.6.1.4.1.994.3.4.7.31.84 | ScalarlicenseLicenseKey | read-write | current | This is the License Key. |
| 1.3.6.1.4.1.994.3.4.7.31.85 | ScalarlicenseExpires | read-only | current | This is the date the current License will expire. |
| 1.3.6.1.4.1.994.3.4.7.31.124 | ScalarlicenseAllowTL1 | read-only | current | This describes the status of TL1 support in the license |
| 1.3.6.1.4.1.994.3.4.7.32 | Tablepe2aHostTable | not-accessible | current | Table for configuration of e2aHost |
| 1.3.6.1.4.1.994.3.4.7.32.1 | Rowpe2aHostEntry | not-accessible | current | Entry for configuration table of e2aHost |
| 1.3.6.1.4.1.994.3.4.7.32.1.3 | Columnpe2aHostDescription | read-write | current | Description of the connection. |
| 1.3.6.1.4.1.994.3.4.7.32.1.10 | Columnpe2aHostConfigured | read-write | current | If set to true, this route will be used by E2A. |
| 1.3.6.1.4.1.994.3.4.7.32.1.14 | Columnpe2aHostIpAddress | read-write | current | The IP address of the remote device. |
| 1.3.6.1.4.1.994.3.4.7.32.1.17 | Columnpe2aHostLevel0 | read-write | current | Alarm level associated with the online state. |
| 1.3.6.1.4.1.994.3.4.7.32.1.18 | Columnpe2aHostLevel1 | read-write | current | Alarm level associated with the offline state. |
| 1.3.6.1.4.1.994.3.4.7.32.1.19 | Columnpe2aHostLevel2 | read-write | current | Alarm level associated with the connecting state. |
| 1.3.6.1.4.1.994.3.4.7.32.1.37 | Columnpe2aHostRosterID | read-write | current | Serial port number to use when connecting to WebMon. |
| 1.3.6.1.4.1.994.3.4.7.32.1.56 | Columnpe2aHostPollAddress | read-write | current | The E2A address of the remote device. |
| 1.3.6.1.4.1.994.3.4.7.32.1.73 | Columnpe2aHostIPPortNum | read-write | current | IP port number to use when connecting to the remote device. |
| 1.3.6.1.4.1.994.3.4.7.32.1.116 | Columnpe2aHostTL1SID | read-write | current | (TL1) System ID associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.32.1.117 | Columnpe2aHostTL1COND | read-write | current | (TL1) Condition text associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.32.1.118 | Columnpe2aHostTL1Eqpt | read-write | current | (TL1) EQPT field associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.32.1.119 | Columnpe2aHostTL1Env | read-write | current | (TL1) Environmental field associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.32.1.120 | Columnpe2aHostTL1Srveff | read-write | current | (TL1) Service Effecting field associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.32.1.121 | Columnpe2aHostTL1Locn | read-write | current | (TL1) Location field associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.32.1.122 | Columnpe2aHostTL1Dirn | read-write | current | (TL1) Direction field associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.32.1.999 | Columnpe2aHostIndex | read-only | current | Index. |
| 1.3.6.1.4.1.994.3.4.7.33 | TablepderivedAnalogTable | not-accessible | current | Table for configuration of derivedAnalog |
| 1.3.6.1.4.1.994.3.4.7.33.1 | RowpderivedAnalogEntry | not-accessible | current | Entry for configuration table of derivedAnalog |
| 1.3.6.1.4.1.994.3.4.7.33.1.3 | ColumnpderivedAnalogDescription | read-write | current | Description of the derived alarm point. |
| 1.3.6.1.4.1.994.3.4.7.33.1.4 | ColumnpderivedAnalogDesc0 | read-write | current | The description for derived values between threshold 0 and threshold 1. |
| 1.3.6.1.4.1.994.3.4.7.33.1.5 | ColumnpderivedAnalogDesc1 | read-write | current | The description for derived values between threshold 1 and threshold 2. |
| 1.3.6.1.4.1.994.3.4.7.33.1.6 | ColumnpderivedAnalogDesc2 | read-write | current | The description for derived values between threshold 2 and threshold 3. |
| 1.3.6.1.4.1.994.3.4.7.33.1.7 | ColumnpderivedAnalogDesc3 | read-write | current | The description for derived values between threshold 3 and threshold 4. |
| 1.3.6.1.4.1.994.3.4.7.33.1.8 | ColumnpderivedAnalogDesc4 | read-write | current | The description for derived values between threshold 4 and threshold 5. |
| 1.3.6.1.4.1.994.3.4.7.33.1.10 | ColumnpderivedAnalogConfigured | read-write | current | If set to true, changes of state will be reported. If set to false, not change of states will be reported. |
| 1.3.6.1.4.1.994.3.4.7.33.1.11 | ColumnpderivedAnalogSendEmail | read-write | current | If set to true, an email will be sent on a change of state. If false, no email will be sent. |
| 1.3.6.1.4.1.994.3.4.7.33.1.12 | ColumnpderivedAnalogSendSNMPTrap | read-write | current | If set to true, an SNMP trap will be sent on a change of state. If false, no SNMP trap will be sent. |
| 1.3.6.1.4.1.994.3.4.7.33.1.17 | ColumnpderivedAnalogLevel0 | read-write | current | The level for derived values between threshold 0 and threshold 1. |
| 1.3.6.1.4.1.994.3.4.7.33.1.18 | ColumnpderivedAnalogLevel1 | read-write | current | The level for derived values between threshold 1 and threshold 2. |
| 1.3.6.1.4.1.994.3.4.7.33.1.19 | ColumnpderivedAnalogLevel2 | read-write | current | The level for derived values between threshold 2 and threshold 3. |
| 1.3.6.1.4.1.994.3.4.7.33.1.20 | ColumnpderivedAnalogLevel3 | read-write | current | The level for derived values between threshold 3 and threshold 4. |
| 1.3.6.1.4.1.994.3.4.7.33.1.21 | ColumnpderivedAnalogLevel4 | read-write | current | The level for derived values between threshold 4 and threshold 5. |
| 1.3.6.1.4.1.994.3.4.7.33.1.28 | ColumnpderivedAnalogThresh0 | read-write | current | This is the maximum analog derived value. |
| 1.3.6.1.4.1.994.3.4.7.33.1.29 | ColumnpderivedAnalogThresh1 | read-write | current | This is the first threshold derived value. |
| 1.3.6.1.4.1.994.3.4.7.33.1.30 | ColumnpderivedAnalogThresh2 | read-write | current | This is the second threshold derived value. |
| 1.3.6.1.4.1.994.3.4.7.33.1.31 | ColumnpderivedAnalogThresh3 | read-write | current | This is the third threshold derived value. |
| 1.3.6.1.4.1.994.3.4.7.33.1.32 | ColumnpderivedAnalogThresh4 | read-write | current | This is the fourth threshold derived value. |
| 1.3.6.1.4.1.994.3.4.7.33.1.33 | ColumnpderivedAnalogThresh5 | read-write | current | This is the minimum threshold derived value. |
| 1.3.6.1.4.1.994.3.4.7.33.1.46 | ColumnpderivedAnalogUnits | read-write | current | Description of the units of measurement. |
| 1.3.6.1.4.1.994.3.4.7.33.1.64 | ColumnpderivedAnalogLiveDescription | read-only | current | The current description of the alarm state. |
| 1.3.6.1.4.1.994.3.4.7.33.1.65 | ColumnpderivedAnalogLiveLevel | read-only | current | The current level of the alarm. |
| 1.3.6.1.4.1.994.3.4.7.33.1.66 | ColumnpderivedAnalogLiveRaw | read-only | current | The current derived reading from the analog devices. This value will alwaysbe between the threshold 0 and threshold 5 values. |
| 1.3.6.1.4.1.994.3.4.7.33.1.67 | ColumnpderivedAnalogLiveTime | read-only | current | The time of the last change of state. |
| 1.3.6.1.4.1.994.3.4.7.33.1.90 | ColumnpderivedAnalogElementAPkg | read-write | current | Package where the alarm point is located for element A. |
| 1.3.6.1.4.1.994.3.4.7.33.1.91 | ColumnpderivedAnalogElementAPoint | read-write | current | Alarm point for element A. |
| 1.3.6.1.4.1.994.3.4.7.33.1.92 | ColumnpderivedAnalogElementBPkg | read-write | current | Package where the alarm point is located for element B. |
| 1.3.6.1.4.1.994.3.4.7.33.1.93 | ColumnpderivedAnalogElementBPoint | read-write | current | Alarm point for element B. |
| 1.3.6.1.4.1.994.3.4.7.33.1.95 | ColumnpderivedAnalogFormula | read-write | current | The formula that will be used to compute the derived alarm. |
| 1.3.6.1.4.1.994.3.4.7.33.1.116 | ColumnpderivedAnalogTL1SID | read-write | current | (TL1) System ID associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.33.1.117 | ColumnpderivedAnalogTL1COND | read-write | current | (TL1) Condition text associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.33.1.118 | ColumnpderivedAnalogTL1Eqpt | read-write | current | (TL1) EQPT field associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.33.1.119 | ColumnpderivedAnalogTL1Env | read-write | current | (TL1) Environmental field associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.33.1.120 | ColumnpderivedAnalogTL1Srveff | read-write | current | (TL1) Service Effecting field associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.33.1.121 | ColumnpderivedAnalogTL1Locn | read-write | current | (TL1) Location field associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.33.1.122 | ColumnpderivedAnalogTL1Dirn | read-write | current | (TL1) Direction field associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.33.1.999 | ColumnpderivedAnalogIndex | read-only | current | Index. |
| 1.3.6.1.4.1.994.3.4.7.34 | TablepgpsTable | not-accessible | current | Table for configuration of gps |
| 1.3.6.1.4.1.994.3.4.7.34.1 | RowpgpsEntry | not-accessible | current | Entry for configuration table of gps |
| 1.3.6.1.4.1.994.3.4.7.34.1.3 | ColumnpgpsDescription | read-only | current | Description of the onboard device. |
| 1.3.6.1.4.1.994.3.4.7.34.1.4 | ColumnpgpsDesc0 | read-write | current | The description for values between threshold 0 and threshold 1. |
| 1.3.6.1.4.1.994.3.4.7.34.1.5 | ColumnpgpsDesc1 | read-write | current | The description for values between threshold 1 and threshold 2. |
| 1.3.6.1.4.1.994.3.4.7.34.1.6 | ColumnpgpsDesc2 | read-write | current | The description for values between threshold 2 and threshold 3. |
| 1.3.6.1.4.1.994.3.4.7.34.1.7 | ColumnpgpsDesc3 | read-write | current | The description for values between threshold 3 and threshold 4. |
| 1.3.6.1.4.1.994.3.4.7.34.1.8 | ColumnpgpsDesc4 | read-write | current | The description for values between threshold 4 and threshold 5. |
| 1.3.6.1.4.1.994.3.4.7.34.1.10 | ColumnpgpsConfigured | read-write | current | If set to true, the onboard sensors will be used. If set to false the will be ignored. |
| 1.3.6.1.4.1.994.3.4.7.34.1.11 | ColumnpgpsSendEmail | read-write | current | If set to true an email event will be set when a threshold is crossed. If set to false no email event will be sent. |
| 1.3.6.1.4.1.994.3.4.7.34.1.12 | ColumnpgpsSendSNMPTrap | read-write | current | If set to true an SNMP trap will be set when a threshold is crossed. If set to false no SNMP trap will be sent. |
| 1.3.6.1.4.1.994.3.4.7.34.1.17 | ColumnpgpsLevel0 | read-write | current | The level for values between threshold 0 and threshold 1. |
| 1.3.6.1.4.1.994.3.4.7.34.1.18 | ColumnpgpsLevel1 | read-write | current | The level for values between threshold 1 and threshold 2. |
| 1.3.6.1.4.1.994.3.4.7.34.1.19 | ColumnpgpsLevel2 | read-write | current | The level for values between threshold 2 and threshold 3. |
| 1.3.6.1.4.1.994.3.4.7.34.1.20 | ColumnpgpsLevel3 | read-write | current | The level for values between threshold 3 and threshold 4. |
| 1.3.6.1.4.1.994.3.4.7.34.1.21 | ColumnpgpsLevel4 | read-write | current | The level for values between threshold 4 and threshold 5. |
| 1.3.6.1.4.1.994.3.4.7.34.1.28 | ColumnpgpsThresh0 | read-only | current | This is the minimun analog value. |
| 1.3.6.1.4.1.994.3.4.7.34.1.29 | ColumnpgpsThresh1 | read-write | current | This is the first threshold value. |
| 1.3.6.1.4.1.994.3.4.7.34.1.30 | ColumnpgpsThresh2 | read-write | current | This is the second threshold value. |
| 1.3.6.1.4.1.994.3.4.7.34.1.31 | ColumnpgpsThresh3 | read-write | current | This is the third threshold value. |
| 1.3.6.1.4.1.994.3.4.7.34.1.32 | ColumnpgpsThresh4 | read-write | current | This is the fourth threshold value. |
| 1.3.6.1.4.1.994.3.4.7.34.1.33 | ColumnpgpsThresh5 | read-only | current | This is the maximum threshold value. |
| 1.3.6.1.4.1.994.3.4.7.34.1.46 | ColumnpgpsUnits | read-only | current | Description of the units of measurement. |
| 1.3.6.1.4.1.994.3.4.7.34.1.64 | ColumnpgpsLiveDescription | read-only | current | The description of the current state of the onboard sensor |
| 1.3.6.1.4.1.994.3.4.7.34.1.65 | ColumnpgpsLiveLevel | read-only | current | The level of the current state of the onboard sensor. |
| 1.3.6.1.4.1.994.3.4.7.34.1.66 | ColumnpgpsLiveRaw | read-only | current | The current reading from the onboard sensor. This value will always be between the threshold 0 and threshold 5 values. |
| 1.3.6.1.4.1.994.3.4.7.34.1.67 | ColumnpgpsLiveTime | read-only | current | The time of the last event. |
| 1.3.6.1.4.1.994.3.4.7.34.1.116 | ColumnpgpsTL1SID | read-write | current | (TL1) System ID associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.34.1.117 | ColumnpgpsTL1COND | read-write | current | (TL1) Condition text associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.34.1.118 | ColumnpgpsTL1Eqpt | read-write | current | (TL1) EQPT field associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.34.1.119 | ColumnpgpsTL1Env | read-write | current | (TL1) Environmental field associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.34.1.120 | ColumnpgpsTL1Srveff | read-write | current | (TL1) Service Effecting field associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.34.1.121 | ColumnpgpsTL1Locn | read-write | current | (TL1) Location field associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.34.1.122 | ColumnpgpsTL1Dirn | read-write | current | (TL1) Direction field associated with this item. |
| 1.3.6.1.4.1.994.3.4.7.34.1.999 | ColumnpgpsIndex | read-only | current | Index. |
| 1.3.6.1.4.1.994.3.4.7.35 | TablepportRedirectTable | not-accessible | current | Table for configuration of portRedirect |
| 1.3.6.1.4.1.994.3.4.7.35.1 | RowpportRedirectEntry | not-accessible | current | Entry for configuration table of portRedirect |
| 1.3.6.1.4.1.994.3.4.7.35.1.3 | ColumnpportRedirectDescription | read-write | current | Description of the connection. |
| 1.3.6.1.4.1.994.3.4.7.35.1.10 | ColumnpportRedirectConfigured | read-write | current | If set to true, this route will be allowed. |
| 1.3.6.1.4.1.994.3.4.7.35.1.14 | ColumnpportRedirectIpAddress | read-write | current | The IP address of the remote device. |
| 1.3.6.1.4.1.994.3.4.7.35.1.23 | ColumnpportRedirectReadPeriod | read-write | current | Inactivity timeout (in minutes). |
| 1.3.6.1.4.1.994.3.4.7.35.1.37 | ColumnpportRedirectRosterID | read-write | current | IP port number to use when connecting to the remote device. |
| 1.3.6.1.4.1.994.3.4.7.35.1.73 | ColumnpportRedirectIPPortNum | read-write | current | IP port number to use when connecting to WebMon. |
| 1.3.6.1.4.1.994.3.4.7.35.1.999 | ColumnpportRedirectIndex | read-only | current | Index. |
| 1.3.6.1.4.1.994.3.4.7.36 | TablepscheduleATable | not-accessible | current | Table for configuration of scheduleA |
| 1.3.6.1.4.1.994.3.4.7.36.1 | RowpscheduleAEntry | not-accessible | current | Entry for configuration table of scheduleA |
| 1.3.6.1.4.1.994.3.4.7.36.1.102 | ColumnpscheduleADayOfWeek | read-only | current | The day of the week |
| 1.3.6.1.4.1.994.3.4.7.36.1.103 | ColumnpscheduleAConfiguredState | read-write | current | The state of the schedule at the beginning of the day. |
| 1.3.6.1.4.1.994.3.4.7.36.1.104 | ColumnpscheduleAConfigured1 | read-write | current | The state of the schedule between time markers 1 and 2. |
| 1.3.6.1.4.1.994.3.4.7.36.1.105 | ColumnpscheduleAConfigured2 | read-write | current | The state of the schedule between time markers 2 and 3. |
| 1.3.6.1.4.1.994.3.4.7.36.1.106 | ColumnpscheduleAConfigured3 | read-write | current | The state of the schedule between time markers 3 and 4. |
| 1.3.6.1.4.1.994.3.4.7.36.1.107 | ColumnpscheduleAConfigured4 | read-write | current | The state of the schedule at the end of the day. |
| 1.3.6.1.4.1.994.3.4.7.36.1.108 | ColumnpscheduleATime0 | read-only | current | Time marker 0, the beginning of the day. |
| 1.3.6.1.4.1.994.3.4.7.36.1.109 | ColumnpscheduleATime1 | read-write | current | Time marker 1. |
| 1.3.6.1.4.1.994.3.4.7.36.1.110 | ColumnpscheduleATime2 | read-write | current | Time marker 2. |
| 1.3.6.1.4.1.994.3.4.7.36.1.111 | ColumnpscheduleATime3 | read-write | current | Time marker 3. |
| 1.3.6.1.4.1.994.3.4.7.36.1.112 | ColumnpscheduleATime4 | read-write | current | Time marker 4. |
| 1.3.6.1.4.1.994.3.4.7.36.1.113 | ColumnpscheduleATime5 | read-only | current | Time marker 5, the end of the day. |
| 1.3.6.1.4.1.994.3.4.7.36.1.999 | ColumnpscheduleAIndex | read-only | current | Index. |
| 1.3.6.1.4.1.994.3.4.7.37 | TablepscheduleBTable | not-accessible | current | Table for configuration of scheduleB |
| 1.3.6.1.4.1.994.3.4.7.37.1 | RowpscheduleBEntry | not-accessible | current | Entry for configuration table of scheduleB |
| 1.3.6.1.4.1.994.3.4.7.37.1.102 | ColumnpscheduleBDayOfWeek | read-only | current | The day of the week |
| 1.3.6.1.4.1.994.3.4.7.37.1.103 | ColumnpscheduleBConfiguredState | read-write | current | The state of the schedule at the beginning of the day. |
| 1.3.6.1.4.1.994.3.4.7.37.1.104 | ColumnpscheduleBConfigured1 | read-write | current | The state of the schedule between time markers 1 and 2. |
| 1.3.6.1.4.1.994.3.4.7.37.1.105 | ColumnpscheduleBConfigured2 | read-write | current | The state of the schedule between time markers 2 and 3. |
| 1.3.6.1.4.1.994.3.4.7.37.1.106 | ColumnpscheduleBConfigured3 | read-write | current | The state of the schedule between time markers 3 and 4. |
| 1.3.6.1.4.1.994.3.4.7.37.1.107 | ColumnpscheduleBConfigured4 | read-write | current | The state of the schedule at the end of the day. |
| 1.3.6.1.4.1.994.3.4.7.37.1.108 | ColumnpscheduleBTime0 | read-only | current | Time marker 0, the beginning of the day. |
| 1.3.6.1.4.1.994.3.4.7.37.1.109 | ColumnpscheduleBTime1 | read-write | current | Time marker 1. |
| 1.3.6.1.4.1.994.3.4.7.37.1.110 | ColumnpscheduleBTime2 | read-write | current | Time marker 2. |
| 1.3.6.1.4.1.994.3.4.7.37.1.111 | ColumnpscheduleBTime3 | read-write | current | Time marker 3. |
| 1.3.6.1.4.1.994.3.4.7.37.1.112 | ColumnpscheduleBTime4 | read-write | current | Time marker 4. |
| 1.3.6.1.4.1.994.3.4.7.37.1.113 | ColumnpscheduleBTime5 | read-only | current | Time marker 5, the end of the day. |
| 1.3.6.1.4.1.994.3.4.7.37.1.999 | ColumnpscheduleBIndex | read-only | current | Index. |
| 1.3.6.1.4.1.994.3.4.7.38 | TablepscheduleCTable | not-accessible | current | Table for configuration of scheduleC |
| 1.3.6.1.4.1.994.3.4.7.38.1 | RowpscheduleCEntry | not-accessible | current | Entry for configuration table of scheduleC |
| 1.3.6.1.4.1.994.3.4.7.38.1.102 | ColumnpscheduleCDayOfWeek | read-only | current | The day of the week |
| 1.3.6.1.4.1.994.3.4.7.38.1.103 | ColumnpscheduleCConfiguredState | read-write | current | The state of the schedule at the beginning of the day. |
| 1.3.6.1.4.1.994.3.4.7.38.1.104 | ColumnpscheduleCConfigured1 | read-write | current | The state of the schedule between time markers 1 and 2. |
| 1.3.6.1.4.1.994.3.4.7.38.1.105 | ColumnpscheduleCConfigured2 | read-write | current | The state of the schedule between time markers 2 and 3. |
| 1.3.6.1.4.1.994.3.4.7.38.1.106 | ColumnpscheduleCConfigured3 | read-write | current | The state of the schedule between time markers 3 and 4. |
| 1.3.6.1.4.1.994.3.4.7.38.1.107 | ColumnpscheduleCConfigured4 | read-write | current | The state of the schedule at the end of the day. |
| 1.3.6.1.4.1.994.3.4.7.38.1.108 | ColumnpscheduleCTime0 | read-only | current | Time marker 0, the beginning of the day. |
| 1.3.6.1.4.1.994.3.4.7.38.1.109 | ColumnpscheduleCTime1 | read-write | current | Time marker 1. |
| 1.3.6.1.4.1.994.3.4.7.38.1.110 | ColumnpscheduleCTime2 | read-write | current | Time marker 2. |
| 1.3.6.1.4.1.994.3.4.7.38.1.111 | ColumnpscheduleCTime3 | read-write | current | Time marker 3. |
| 1.3.6.1.4.1.994.3.4.7.38.1.112 | ColumnpscheduleCTime4 | read-write | current | Time marker 4. |
| 1.3.6.1.4.1.994.3.4.7.38.1.113 | ColumnpscheduleCTime5 | read-only | current | Time marker 5, the end of the day. |
| 1.3.6.1.4.1.994.3.4.7.38.1.999 | ColumnpscheduleCIndex | read-only | current | Index. |
| 1.3.6.1.4.1.994.3.4.7.39 | TablepscheduleDTable | not-accessible | current | Table for configuration of scheduleD |
| 1.3.6.1.4.1.994.3.4.7.39.1 | RowpscheduleDEntry | not-accessible | current | Entry for configuration table of scheduleD |
| 1.3.6.1.4.1.994.3.4.7.39.1.102 | ColumnpscheduleDDayOfWeek | read-only | current | The day of the week |
| 1.3.6.1.4.1.994.3.4.7.39.1.103 | ColumnpscheduleDConfiguredState | read-write | current | The state of the schedule at the beginning of the day. |
| 1.3.6.1.4.1.994.3.4.7.39.1.104 | ColumnpscheduleDConfigured1 | read-write | current | The state of the schedule between time markers 1 and 2. |
| 1.3.6.1.4.1.994.3.4.7.39.1.105 | ColumnpscheduleDConfigured2 | read-write | current | The state of the schedule between time markers 2 and 3. |
| 1.3.6.1.4.1.994.3.4.7.39.1.106 | ColumnpscheduleDConfigured3 | read-write | current | The state of the schedule between time markers 3 and 4. |
| 1.3.6.1.4.1.994.3.4.7.39.1.107 | ColumnpscheduleDConfigured4 | read-write | current | The state of the schedule at the end of the day. |
| 1.3.6.1.4.1.994.3.4.7.39.1.108 | ColumnpscheduleDTime0 | read-only | current | Time marker 0, the beginning of the day. |
| 1.3.6.1.4.1.994.3.4.7.39.1.109 | ColumnpscheduleDTime1 | read-write | current | Time marker 1. |
| 1.3.6.1.4.1.994.3.4.7.39.1.110 | ColumnpscheduleDTime2 | read-write | current | Time marker 2. |
| 1.3.6.1.4.1.994.3.4.7.39.1.111 | ColumnpscheduleDTime3 | read-write | current | Time marker 3. |
| 1.3.6.1.4.1.994.3.4.7.39.1.112 | ColumnpscheduleDTime4 | read-write | current | Time marker 4. |
| 1.3.6.1.4.1.994.3.4.7.39.1.113 | ColumnpscheduleDTime5 | read-only | current | Time marker 5, the end of the day. |
| 1.3.6.1.4.1.994.3.4.7.39.1.999 | ColumnpscheduleDIndex | read-only | current | Index. |
| 1.3.6.1.4.1.994.3.4.7.40 | Nodetl1Settings | |||
| 1.3.6.1.4.1.994.3.4.7.40.123 | Scalartl1SettingsTL1Issue | read-write | current | (TL1) TL1 issue associated with this device. |
| 1.3.6.1.4.1.994.3.4.7.41 | TablepDCPFProtocolTable | not-accessible | current | Table for configuration of DCPFProtocol |
| 1.3.6.1.4.1.994.3.4.7.41.1 | RowpDCPFProtocolEntry | not-accessible | current | Entry for configuration table of DCPFProtocol |
| 1.3.6.1.4.1.994.3.4.7.41.1.3 | ColumnpDCPFProtocolDescription | read-only | current | Description of the input device that DCPF will poll. |
| 1.3.6.1.4.1.994.3.4.7.41.1.10 | ColumnpDCPFProtocolConfigured | read-write | current | If set to true, this input will be polled in DCPF. If set to false, it will not be polled. |
| 1.3.6.1.4.1.994.3.4.7.41.1.127 | ColumnpDCPFProtocolBaseDCPFDisplay | read-write | current | Base DCPF display for this input device. |
| 1.3.6.1.4.1.994.3.4.7.41.1.999 | ColumnpDCPFProtocolIndex | read-only | current | Index. |
| 1.3.6.1.4.1.994.3.4.7.42 | NodedcpfSettings | |||
| 1.3.6.1.4.1.994.3.4.7.42.128 | ScalardcpfSettingsDCPFAddress | read-write | current | Base DCPF Address. |
| 1.3.6.1.4.1.994.3.4.7.43 | TablepTABSProtocolTable | not-accessible | current | Table for configuration of TABSProtocol |
| 1.3.6.1.4.1.994.3.4.7.43.1 | RowpTABSProtocolEntry | not-accessible | current | Entry for configuration table of TABSProtocol |
| 1.3.6.1.4.1.994.3.4.7.43.1.3 | ColumnpTABSProtocolDescription | read-only | current | Description of the input device that TABS will poll. |
| 1.3.6.1.4.1.994.3.4.7.43.1.10 | ColumnpTABSProtocolConfigured | read-write | current | If set to true, this input will be polled in TABS. If set to false, it will not be polled. |
| 1.3.6.1.4.1.994.3.4.7.43.1.129 | ColumnpTABSProtocolBaseTABSDisplay | read-write | current | Base TABS display for this input device. |
| 1.3.6.1.4.1.994.3.4.7.43.1.999 | ColumnpTABSProtocolIndex | read-only | current | Index. |
| 1.3.6.1.4.1.994.3.4.7.44 | NodetabsSettings | |||
| 1.3.6.1.4.1.994.3.4.7.44.130 | ScalartabsSettingsTABSAddress | read-write | current | Base TABS Address. |
| 1.3.6.1.4.1.994.3.4.7.45 | TablepsnmpCommandsTable | not-accessible | current | Table for configuration of snmpCommands |
| 1.3.6.1.4.1.994.3.4.7.45.1 | RowpsnmpCommandsEntry | not-accessible | current | Entry for configuration table of snmpCommands |
| 1.3.6.1.4.1.994.3.4.7.45.1.3 | ColumnpsnmpCommandsDescription | read-write | current | Name for this SNMP command. |
| 1.3.6.1.4.1.994.3.4.7.45.1.10 | ColumnpsnmpCommandsConfigured | read-write | current | If set to true, this command will be sent for matching events. If set to false, it will not be sent. |
| 1.3.6.1.4.1.994.3.4.7.45.1.14 | ColumnpsnmpCommandsIpAddress | read-write | current | Target (receiver) IP address of this SNMP command. |
| 1.3.6.1.4.1.994.3.4.7.45.1.39 | ColumnpsnmpCommandsGet | read-write | current | SNMP community used with this command. |
| 1.3.6.1.4.1.994.3.4.7.45.1.42 | ColumnpsnmpCommandsSnmpVersion | read-write | current | SNMP version to be used with this command. |
| 1.3.6.1.4.1.994.3.4.7.45.1.49 | ColumnpsnmpCommandsOutputAuto | read-write | current | Source alarm point for this SNMP command. |
| 1.3.6.1.4.1.994.3.4.7.45.1.71 | ColumnpsnmpCommandsOutputAutoPkg | read-write | current | Package where the source alarm point is located. |
| 1.3.6.1.4.1.994.3.4.7.45.1.73 | ColumnpsnmpCommandsIPPortNum | read-write | current | Target (receiver) IP port of this SNMP command. |
| 1.3.6.1.4.1.994.3.4.7.45.1.132 | ColumnpsnmpCommandsOID | read-write | current | Target OID used with this command |
| 1.3.6.1.4.1.994.3.4.7.45.1.134 | ColumnpsnmpCommandsSNMPVarbindType | read-write | current | Type of value sent to target, if this is a set command. |
| 1.3.6.1.4.1.994.3.4.7.45.1.135 | ColumnpsnmpCommandsTextNormal | read-write | current | Value sent to target for normal condition for a set command. |
| 1.3.6.1.4.1.994.3.4.7.45.1.136 | ColumnpsnmpCommandsTextCritical | read-write | current | Value sent to target for critical condition for a set command. |
| 1.3.6.1.4.1.994.3.4.7.45.1.137 | ColumnpsnmpCommandsTextMajor | read-write | current | Value sent to target for major condition for a set command. |
| 1.3.6.1.4.1.994.3.4.7.45.1.138 | ColumnpsnmpCommandsTextMinor | read-write | current | Value sent to target for minor condition for a set command. |
| 1.3.6.1.4.1.994.3.4.7.45.1.139 | ColumnpsnmpCommandsTextStatus | read-write | current | Value sent to target for status condition for a set command. |
| 1.3.6.1.4.1.994.3.4.7.45.1.999 | ColumnpsnmpCommandsIndex | read-only | current | Index. |
| 1.3.6.1.4.1.994.3.4.7.46 | NodebattMon | |||
| 1.3.6.1.4.1.994.3.4.7.46.10 | ScalarbattMonConfigured | read-write | current | If set to true, this command will be sent for matching events. If set to false, it will not be sent. |
| 1.3.6.1.4.1.994.3.4.7.46.49 | ScalarbattMonOutputAuto | read-write | current | Source alarm point for this SNMP command. |
| 1.3.6.1.4.1.994.3.4.7.46.71 | ScalarbattMonOutputAutoPkg | read-write | current | Package where the source alarm point is located. |
| 1.3.6.1.4.1.994.3.4.7.999 | GroupconfigObjectGroup | current | Description. | |
| 1.3.6.1.4.1.994.3.4.8 | Nodetriggers | |||
| 1.3.6.1.4.1.994.3.4.8.1 | ScalarresetDevice | read-write | current | Setting this item to true will cause a reset of the device. Setting this item to false will have no effect. |
| 1.3.6.1.4.1.994.3.4.8.2 | ScalarcommitAccountChanges | read-write | current | Setting this item to true will cause any user account changes to go into effect immediatly. Setting this item to false will have no effect. |
| 1.3.6.1.4.1.994.3.4.8.3 | ScalarresendEvents | read-write | current | Setting this item to true will cause the device to resend traps for any standing alarms. Setting this item to false will have no effect. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| AnalogState | INTEGER { highHigh(0), high(1), medium(2), low(3), lowLow(4) } | current | Defines states for an analog input. |
| BaudRate | INTEGER { baud-300(300), baud-600(600), baud-1200(1200), baud-2400(2400), baud-4800(4800), baud-9600(9600), baud-19200(19200), baud-28800(28800), baud-38400(38400) } | current | Defines baud rates for serial communication. |
| Boolean | INTEGER { false(0), true(1) } | current | A type with only two states. |
| CameraStyle | INTEGER { d-link-dcs1000(0), sony-snc-rz30n(1), axis-2100(2), d-link-dcs2000(3), d-link-dcs5300(4), axis-210(5), axis-m1103(6) } | current | Defines the different types of IP cameras supported. |
| Configured | INTEGER { not-in-use(0), always-in-use(1), schedule-a(2), schedule-b(3), schedule-c(4), schedule-d(5) } | current | In use |
| ConfiguredState | INTEGER { disabled(0), enabled(1) } | current | |
| ConnectivityState | INTEGER { online(0), offline(1) } | current | Used for the state of a connection. |
| ContactStyle | INTEGER { dry-contact(0), wet-contact(1) } | current | Defines the different types of discrete alarm contacts. |
| DataBits | INTEGER { data-bits-7(7), data-bits-8(8) } | current | Defines the number of data bits in a byte for serial communication. |
| DayOfWeek | INTEGER { sunday(0), monday(1), tuesday(2), wednesday(3), thursday(4), friday(5), saturday(6) } | current | Day of the week |
| DescriptionString | OCTET STRING (SIZE (0..80)) | current | A character string used for descriptions. |
| DigitalState | INTEGER { off(0), on(1) } | current | A type with only two states, used specifically to represent the state of a digital reading. |
| DiscreteFormula | INTEGER { a-and-b(0), not-a-and-b(1), a-and-not-b(2), not-a-and-not-b(3), a-or-b(4), not-a-or-b(5), a-or-not-b(6), not-a-or-not-b(7), a-xor-b(8), not-a-xor-b(9), a-xor-not-b(10), not-a-xor-not-b(11) } | current | Defines the type of formula used for derived discretes. |
| EthernetRate | INTEGER { allow-100-mbps(0), force-10-mbps(1) } | current | Ethernet Rate |
| EthernetType | INTEGER { allow-full-duplex(0), force-half-duplex(1) } | current | Ethernet Type |
| IOFormat | INTEGER { single-pin(0), single-pin-with-ground(1), two-pins(2), two-pins-with-ground(3), two-pins-right-to-left(4), three-pins(5), three-pins-right-to-left(6), rj(7), onboard-built-in(8) } | current | Defines the physical pin layout of slot cards. |
| Level | INTEGER { normal(0), critical(1), major(2), minor(3), status(4) } | current | Describes a priority or level. |
| MeasureStyle | INTEGER { english(0), metric(1) } | current | Defines state of measurement style English or Metic. |
| MODBUSCommand | INTEGER { read-holding-register(3), read-input-register(4) } | current | Function code |
| OutputMode | INTEGER { manual(0), automatic(1) } | current | Defines the different ways a control point can be activated. |
| OutputState | INTEGER { open(0), closed(1) } | current | Defines states for an output. |
| Parity | INTEGER { none(0), even-parity(1), odd-parity(2) } | current | Defines the parity for serial communication. |
| PortType | INTEGER { not-present(0), rs-232(1), rs-485(2), dialup(3), iden(4), e2a(5), cdma(6), gps(7), edge(8), t202(9) } | current | Defines the type of serial port. |
| ProductType | INTEGER { webmon-edge(0), webmon-matrix(1) } | current | Defines the type of device. |
| Protocol | INTEGER { none(0), command-line(1), modbus-interrogation(2), configuration-transfer(3), ip-switchboard(4), terminal-server(5), user-login(6), modem-mode(7), ppp-server(8), dcm-responder(9), ascii-log-single-line(10), e2a-host(11), gps-reader(12), port-redirect(13), sensor-reader(14), tl1-responder(15), dcpf-responder(16), lcd-protocol(17), tabs-responder(18), configuration-menu(19) } | current | Defines different protocols used for communication. |
| SensorType | INTEGER { raw(0), temperature(1), humidity(2) } | current | Sensor Type |
| SerialCTS | INTEGER { cts-ignore(0), cts-require(1) } | current | Defines the different CTS states for serial communication. |
| SerialRTS | INTEGER { rts-never-on(0), rts-always-on(1), rts-on-for-transmit(2) } | current | Defines the different RTS states for serial communication. |
| SlotId | INTEGER { empty(0), discrete-inputs(1), discrete-outputs(2), serial-ports(3), onboard-sensors(4), analog-inputs(5), switch-ports(6), sensor-inputs(7) } | current | Defines the different types of slot types available. |
| SNMPAccess | INTEGER { noauthnopriv(0), authnopriv-md5(1), authpriv-md5(2), authnopriv-sha(3), authpriv-sha(4) } | current | Auth/Priv type |
| SNMPCommandType | INTEGER { get(160), set(163) } | current | Command type |
| SNMPVarbindType | INTEGER { integer(2), string(4) } | current | Value type |
| SnmpVersion | INTEGER { snmpv1(0), snmpv2c(1), snmpv3(2), snmpv2c-inform(3), snmpv3-inform(4) } | current | Defines which version of SNMP is used for traps. |
| StopBits | INTEGER { stop-bit-1(1), stop-bits-2(2) } | current | Defines the number of stop bits in a byte for serial communication. |
| TL1Dirn | INTEGER { blank(0), trmt(1), rcv(2), na(3) } | current | Direction |
| TL1Issue | INTEGER { issue-3(3), issue-5(5) } | current | TL1 Issue |
| TL1Locn | INTEGER { blank(0), nend(1), fend(2), line(3) } | current | Location |
| TL1Srveff | INTEGER { blank(0), sa(1), nsa(2) } | current | Service Effecting |
| UseDialout | INTEGER { never(0), always(1), as-backup(2) } | current | Use Dialout |
| VoltageRange | INTEGER { plus-minus-100-volts(100), sensor-port(5) } | current | Defines the valid voltage ranges. |