WHISP-PLV-MODEM-MIB
129 objects
Initial Version.
Imported Objects
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Integer32 IpAddress MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE |
| SNMPv2-TC | DisplayString MacAddress |
| WHISP-GLOBAL-REG-MIB | whispPlvModem |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.161.19.3.7.1 | IdentitywhispPlvModemMIB | Initial Version. | ||
| 1.3.6.1.4.1.161.19.3.7.1.1 | NodewhispPlvModemObjects | |||
| 1.3.6.1.4.1.161.19.3.7.1.1.1 | NodewhispPlvModemInfo | |||
| 1.3.6.1.4.1.161.19.3.7.1.1.1.1 | ScalarmodemInfoModel | read-only | current | This object indicates the Modem Model Number. |
| 1.3.6.1.4.1.161.19.3.7.1.1.1.2 | ScalarmodemInfoSerialNumber | read-only | current | This object indicates the Modem Serial Number. |
| 1.3.6.1.4.1.161.19.3.7.1.1.1.3 | ScalarmodemInfoDeviceMac | read-only | current | This object indicates the Modem Device MAC Address. |
| 1.3.6.1.4.1.161.19.3.7.1.1.1.4 | ScalarmodemInfoPlcMac | read-only | current | This object indicates the Modem PLC MAC Address |
| 1.3.6.1.4.1.161.19.3.7.1.1.1.5 | ScalarmodemInfoHardwareVer | read-only | current | This object indicates the Modem Hardware Version. |
| 1.3.6.1.4.1.161.19.3.7.1.1.1.6 | ScalarmodemInfoDeviceFirmwareVer | read-only | current | This object indicates the Modem Firmware Version. |
| 1.3.6.1.4.1.161.19.3.7.1.1.1.7 | ScalarmodemInfoBootLoaderVer | read-only | current | This object indicates the Modem Boot Loader Version. |
| 1.3.6.1.4.1.161.19.3.7.1.1.1.8 | ScalarmodemInfoSimFirmwareVer | read-only | current | This object indicates the Intellon Simple Module Firmware Version. |
| 1.3.6.1.4.1.161.19.3.7.1.1.1.9 | ScalarmodemInfoDeviceUpgradeStatus | read-only | current | This object indicates the Modems last Software Upgrade Status. 1 - Upgrade not started 2 - Upgrade in progress 3 - Last Upgrade failed 4 - Last Upgrade was suc… |
| 1.3.6.1.4.1.161.19.3.7.1.1.1.10 | ScalarmodemInfoSimUpgradeStatus | read-only | current | This object indicates the Intellon Simple Module Firmware Upgrade Status. 1 - Upgrade not started 2 - Upgrade in progress 3 - Last Upgrade failed 4 - Last Upgr… |
| 1.3.6.1.4.1.161.19.3.7.1.1.1.11 | ScalarmodemInfoCurrentMode | read-only | current | This object indicates the current operating mode of the Modem. 1 - Bridge Mode 2 - NAT Mode. |
| 1.3.6.1.4.1.161.19.3.7.1.1.1.12 | ScalarmodemInfoActiveBandwidthConfig | read-only | current | This object indicates if the Active Bandwidth settings are either Configured OR Provisioned. |
| 1.3.6.1.4.1.161.19.3.7.1.1.1.13 | ScalarmodemInfoActiveUpLinkBandwidth | read-only | current | This object indicates if the Active Bandwidth settings are either Configured OR Provisioned. |
| 1.3.6.1.4.1.161.19.3.7.1.1.1.14 | ScalarmodemInfoActiveDownLinkBandwidth | read-only | current | This object indicates if the Active Bandwidth settings are either Configured OR Provisioned. |
| 1.3.6.1.4.1.161.19.3.7.1.1.2 | NodewhispPlvModemConfig | |||
| 1.3.6.1.4.1.161.19.3.7.1.1.2.1 | ScalarmodemConfPacketPriorityConfig | read-write | current | This object is used to configure 802.1p Packet Priority type. 1 - Fixed QoS 2 - QoS Based on ToS. |
| 1.3.6.1.4.1.161.19.3.7.1.1.2.2 | ScalarmodemConfFixedQoSConfig | read-write | current | This object is used to configure Fixed QoS type. |
| 1.3.6.1.4.1.161.19.3.7.1.1.2.3 | ScalarmodemConfUpLinkDataRate | read-write | current | This object is used to configure Uplink Data Rate. |
| 1.3.6.1.4.1.161.19.3.7.1.1.2.4 | ScalarmodemConfDownLinkDataRate | read-write | current | This object is used to configure Downlink Data Rate. |
| 1.3.6.1.4.1.161.19.3.7.1.1.2.5 | ScalarmodemConfPSD | read-write | current | This object indicates the Power Spectral Density of the signal, at all the 84 carriers, that the device transmits. Starting at the left most octet, which repre… |
| 1.3.6.1.4.1.161.19.3.7.1.1.2.6 | ScalarmodemConfUpLinkMir | read-write | current | This object is used to configure Uplink Maximum Information Rate. This object is for configuring the Data Rate in Kbps, instead of enumerations, as in 'modemCo… |
| 1.3.6.1.4.1.161.19.3.7.1.1.2.7 | ScalarmodemConfDownLinkMir | read-write | current | This object is used to configure Downlink Maximum Information Rate. This object is for configuring the Data Rate in Kbps, instead of enumerations, as in 'modem… |
| 1.3.6.1.4.1.161.19.3.7.1.1.3 | NodewhispPlvModemTrapConfig | |||
| 1.3.6.1.4.1.161.19.3.7.1.1.3.1 | ScalarmodemConfTrapIp1 | read-write | current | This object is used to configure IP Address of SNMP Trap Client #1. |
| 1.3.6.1.4.1.161.19.3.7.1.1.3.2 | ScalarmodemConfTrapCommStr1 | read-write | current | This object is used to configure SNMP CommStrunity string for Trap Client #1. |
| 1.3.6.1.4.1.161.19.3.7.1.1.3.3 | ScalarmodemConfTrapIp2 | read-write | current | This object is used to configure IP Address of SNMP Trap Client #2. |
| 1.3.6.1.4.1.161.19.3.7.1.1.3.4 | ScalarmodemConfTrapCommStr2 | read-write | current | This object is used to configure SNMP CommStrunity string for Trap Client #2. |
| 1.3.6.1.4.1.161.19.3.7.1.1.3.5 | ScalarmodemConfTrapIp3 | read-write | current | This object is used to configure IP Address of SNMP Trap Client #3. |
| 1.3.6.1.4.1.161.19.3.7.1.1.3.6 | ScalarmodemConfTrapCommStr3 | read-write | current | This object is used to configure SNMP CommStrunity string for Trap Client #3. |
| 1.3.6.1.4.1.161.19.3.7.1.1.3.7 | ScalarmodemConfTrapIp4 | read-write | current | This object is used to configure IP Address of SNMP Trap Client #4. |
| 1.3.6.1.4.1.161.19.3.7.1.1.3.8 | ScalarmodemConfTrapCommStr4 | read-write | current | This object is used to configure SNMP CommStrunity string for Trap Client #4. |
| 1.3.6.1.4.1.161.19.3.7.1.1.3.9 | ScalarmodemConfTrapIp5 | read-write | current | This object is used to configure IP Address of SNMP Trap Client #5. |
| 1.3.6.1.4.1.161.19.3.7.1.1.3.10 | ScalarmodemConfTrapCommStr5 | read-write | current | This object is used to configure SNMP CommStrunity string for Trap Client #5. |
| 1.3.6.1.4.1.161.19.3.7.1.1.3.11 | ScalarmodemConfTrapIp6 | read-write | current | This object is used to configure IP Address of SNMP Trap Client #6. |
| 1.3.6.1.4.1.161.19.3.7.1.1.3.12 | ScalarmodemConfTrapCommStr6 | read-write | current | This object is used to configure SNMP CommStrunity string for Trap Client #6. |
| 1.3.6.1.4.1.161.19.3.7.1.1.3.13 | ScalarmodemConfTrapIp7 | read-write | current | This object is used to configure IP Address of SNMP Trap Client #7. |
| 1.3.6.1.4.1.161.19.3.7.1.1.3.14 | ScalarmodemConfTrapCommStr7 | read-write | current | This object is used to configure SNMP CommStrunity string for Trap Client #7. |
| 1.3.6.1.4.1.161.19.3.7.1.1.3.15 | ScalarmodemConfTrapIp8 | read-write | current | This object is used to configure IP Address of SNMP Trap Client #8. |
| 1.3.6.1.4.1.161.19.3.7.1.1.3.16 | ScalarmodemConfTrapCommStr8 | read-write | current | This object is used to configure SNMP CommStrunity string for Trap Client #8. |
| 1.3.6.1.4.1.161.19.3.7.1.1.3.17 | ScalarmodemConfTrapIp9 | read-write | current | This object is used to configure IP Address of SNMP Trap Client #9. |
| 1.3.6.1.4.1.161.19.3.7.1.1.3.18 | ScalarmodemConfTrapCommStr9 | read-write | current | This object is used to configure SNMP CommStrunity string for Trap Client #9. |
| 1.3.6.1.4.1.161.19.3.7.1.1.3.19 | ScalarmodemConfTrapIp10 | read-write | current | This object is used to configure IP Address of SNMP Trap Client #10. |
| 1.3.6.1.4.1.161.19.3.7.1.1.3.20 | ScalarmodemConfTrapCommStr10 | read-write | current | This object is used to configure SNMP CommStrunity string for Trap Client #10. |
| 1.3.6.1.4.1.161.19.3.7.1.1.4 | NodewhispPlvModemAdmConfig | |||
| 1.3.6.1.4.1.161.19.3.7.1.1.4.1 | ScalarmodemAdmConfIpConfig | read-write | current | This object is used to enable or disable the DHCP client, to configure LAN IP Address of the Modem. If the NAT functionality is enabled in the Modem, user will… |
| 1.3.6.1.4.1.161.19.3.7.1.1.4.2 | ScalarmodemAdmConfIp | read-write | current | This object is used to configure IP Address of the Modem. If the NAT functionality is enabled in the Modem, then this object represents the LAN IP Address. |
| 1.3.6.1.4.1.161.19.3.7.1.1.4.3 | ScalarmodemAdmConfIpSubnetMask | read-write | current | This object is used to configure IP Subnet Mask of the Modem. If the NAT functionality is enabled in the Modem, then this object represents the LAN IP Subnet M… |
| 1.3.6.1.4.1.161.19.3.7.1.1.4.4 | ScalarmodemAdmConfNEK | read-write | current | This object is used to configure Network Encryption Key of the Modem. |
| 1.3.6.1.4.1.161.19.3.7.1.1.4.5 | ScalarmodemAdmConfSnmpGetCommStr | read-write | current | This object is used to configure SNMP 'Read' community string of the Modem. |
| 1.3.6.1.4.1.161.19.3.7.1.1.4.6 | ScalarmodemAdmConfSnmpSetCommStr | read-write | current | This object is used to configure SNMP 'Read-Write' community string of the Modem. |
| 1.3.6.1.4.1.161.19.3.7.1.1.4.7 | ScalarmodemAdmConfSnmpAdminCommStr | read-write | current | This object is used to configure SNMP 'Admin' community string of the Modem. |
| 1.3.6.1.4.1.161.19.3.7.1.1.4.8 | ScalarmodemAdmConfLoginUsername | read-write | current | This object is used to configure Modem's System Management Login Username. |
| 1.3.6.1.4.1.161.19.3.7.1.1.4.9 | ScalarmodemAdmConfLoginPassword | read-write | current | This object is used to configure Modem's System Management Login Password. |
| 1.3.6.1.4.1.161.19.3.7.1.1.4.10 | ScalarmodemAdmConfFtpServerIp | read-write | current | This object is used to configure IP Address of FTP server hosting auto-upgrade files. |
| 1.3.6.1.4.1.161.19.3.7.1.1.4.11 | ScalarmodemAdmConfFtpUsername | read-write | current | This object is used to configure Username to login to a FTP server, for use with FTP-based auto-upgrade. |
| 1.3.6.1.4.1.161.19.3.7.1.1.4.12 | ScalarmodemAdmConfFtpPassword | read-write | current | This object is used to configure Password to login to a FTP server, for use with FTP-based auto-upgrade. |
| 1.3.6.1.4.1.161.19.3.7.1.1.4.13 | ScalarmodemAdmConfFtpFile | read-write | current | This object is used to configure Path and/or Filename of the firmware file, for use with FTP-based auto-upgrade. |
| 1.3.6.1.4.1.161.19.3.7.1.1.4.14 | ScalarmodemAdmConfDeviceUpgradeStart | read-write | current | This object is used to start Firmware Upgrade process in the Modem. To start the upgrade process, this object should be set to '1'. |
| 1.3.6.1.4.1.161.19.3.7.1.1.4.15 | ScalarmodemAdmConfSimUpgradeStart | read-write | current | This object is used to start Intellon Simple Module Firmware Upgrade process. To start the upgrade process, this object should be set to '1'. |
| 1.3.6.1.4.1.161.19.3.7.1.1.4.16 | ScalarmodemAdmConfSystemReboot | read-write | current | This object is used to Reboot the Modem. To reboot the modem, this object should be set to '1'. |
| 1.3.6.1.4.1.161.19.3.7.1.1.4.17 | ScalarmodemAdmConfReset | read-write | current | This object is used to reset the Modem configuration to Factory Defaults. To reset the modem configuration to factory defaults, this object should be set to '1… |
| 1.3.6.1.4.1.161.19.3.7.1.1.5 | NodewhispPlvModemAdmWConfig | |||
| 1.3.6.1.4.1.161.19.3.7.1.1.5.1 | ScalarmodemAdmWConfNatConfig | read-write | current | This object is used to Enable or Disable the NAT Functionality in the Modem. |
| 1.3.6.1.4.1.161.19.3.7.1.1.5.2 | ScalarmodemAdmWConfWanConfig | read-write | current | This object is used to Enable or Disable DHCP client, to configure the WAN IP Address. This object is accessible only when NAT functionality is enabled in the … |
| 1.3.6.1.4.1.161.19.3.7.1.1.5.3 | ScalarmodemAdmWConfWanIp | read-write | current | This object is used to configure WAN IP Address of the Modem. This object is accessible only when NAT functionality is enabled in the Modem. |
| 1.3.6.1.4.1.161.19.3.7.1.1.5.4 | ScalarmodemAdmWConfSubnetMask | read-write | current | This object is used to configure WAN IP Subnet Mask of the Modem. This object is accessible only when NAT functionality is enabled in the Modem. |
| 1.3.6.1.4.1.161.19.3.7.1.1.5.5 | ScalarmodemAdmWConfGateway | read-write | current | This object is used to configure Default Gateway IP of the Modem. This object is accessible only when NAT functionality is enabled in the Modem. |
| 1.3.6.1.4.1.161.19.3.7.1.1.5.6 | ScalarmodemAdmWConfDNS1 | read-write | current | This object is used to configure DNS Server #1. This object is accessible only when NAT functionality is enabled in the Modem. |
| 1.3.6.1.4.1.161.19.3.7.1.1.5.7 | ScalarmodemAdmWConfDNS2 | read-write | current | This object is used to configure DNS Server #2. This object is accessible only when NAT functionality is enabled in the Modem. |
| 1.3.6.1.4.1.161.19.3.7.1.1.5.8 | ScalarmodemAdmWConfDhcpConfig | read-write | current | This object is used to Enable or Disable DHCP Server. This object is accessible only when NAT functionality is enabled in the Modem. |
| 1.3.6.1.4.1.161.19.3.7.1.1.5.9 | ScalarmodemAdmWConfDhcpStartIp | read-write | current | This object is used to configure Starting Address of the IP address block, that the DHCP Server can assign to its clients. This object is accessible only when … |
| 1.3.6.1.4.1.161.19.3.7.1.1.5.10 | ScalarmodemAdmWConfDhcpEndIp | read-write | current | This object is used to configure Last Address of the IP address block, that the DHCP Server can assign to its clients. This object is accessible only when NAT … |
| 1.3.6.1.4.1.161.19.3.7.1.1.5.11 | ScalarmodemAdmWConfDhcpLeaseTime | read-write | current | This object is used to configure time period for which the IP address assigned to a client is valid. This object is accessible only when NAT functionality is e… |
| 1.3.6.1.4.1.161.19.3.7.1.1.5.12 | ScalarmodemAdmWConfDmzConfig | read-write | current | This object is used to Enable or Disable the DMZ in the MOdem. This object is accessible only when NAT functionality is enabled in the Modem. |
| 1.3.6.1.4.1.161.19.3.7.1.1.5.13 | ScalarmodemAdmWConfDmzIp | read-write | current | This object is used to configure DMZ IP Address of the Modem. This object is accessible only when NAT functionality is enabled in the Modem. |
| 1.3.6.1.4.1.161.19.3.7.1.1.6 | NodewhispPlvModemAdmSnmpAcessConfig | |||
| 1.3.6.1.4.1.161.19.3.7.1.1.6.1 | ScalarmodemAdmSnmpAccessIpNetwork1 | read-write | current | This object is used to configure SNMP Access Network Address #1. |
| 1.3.6.1.4.1.161.19.3.7.1.1.6.2 | ScalarmodemAdmSnmpAccessIpNetworkMask1 | read-write | current | This object is used to configure SNMP Access Network Address Mask #1. |
| 1.3.6.1.4.1.161.19.3.7.1.1.6.3 | ScalarmodemAdmSnmpAccessIpNetwork2 | read-write | current | This object is used to configure SNMP Access Network Address #2. |
| 1.3.6.1.4.1.161.19.3.7.1.1.6.4 | ScalarmodemAdmSnmpAccessIpNetworkMask2 | read-write | current | This object is used to configure SNMP Access Network Address Mask #2. |
| 1.3.6.1.4.1.161.19.3.7.1.1.6.5 | ScalarmodemAdmSnmpAccessIpNetwork3 | read-write | current | This object is used to configure SNMP Access Network Address #3. |
| 1.3.6.1.4.1.161.19.3.7.1.1.6.6 | ScalarmodemAdmSnmpAccessIpNetworkMask3 | read-write | current | This object is used to configure SNMP Access Network Address Mask #3. |
| 1.3.6.1.4.1.161.19.3.7.1.1.6.7 | ScalarmodemAdmSnmpAccessIpNetwork4 | read-write | current | This object is used to configure SNMP Access Network Address #4. |
| 1.3.6.1.4.1.161.19.3.7.1.1.6.8 | ScalarmodemAdmSnmpAccessIpNetworkMask4 | read-write | current | This object is used to configure SNMP Access Network Address Mask #4. |
| 1.3.6.1.4.1.161.19.3.7.1.1.6.9 | ScalarmodemAdmSnmpAccessIpNetwork5 | read-write | current | This object is used to configure SNMP Access Network Address #5. |
| 1.3.6.1.4.1.161.19.3.7.1.1.6.10 | ScalarmodemAdmSnmpAccessIpNetworkMask5 | read-write | current | This object is used to configure SNMP Access Network Address Mask #5. |
| 1.3.6.1.4.1.161.19.3.7.1.1.6.11 | ScalarmodemAdmSnmpAccessIpNetwork6 | read-write | current | This object is used to configure SNMP Access Network Address #6. |
| 1.3.6.1.4.1.161.19.3.7.1.1.6.12 | ScalarmodemAdmSnmpAccessIpNetworkMask6 | read-write | current | This object is used to configure SNMP Access Network Address Mask #6. |
| 1.3.6.1.4.1.161.19.3.7.1.1.6.13 | ScalarmodemAdmSnmpAccessIpNetwork7 | read-write | current | This object is used to configure SNMP Access Network Address #7. |
| 1.3.6.1.4.1.161.19.3.7.1.1.6.14 | ScalarmodemAdmSnmpAccessIpNetworkMask7 | read-write | current | This object is used to configure SNMP Access Network Address Mask #7. |
| 1.3.6.1.4.1.161.19.3.7.1.1.6.15 | ScalarmodemAdmSnmpAccessIpNetwork8 | read-write | current | This object is used to configure SNMP Access Network Address #8. |
| 1.3.6.1.4.1.161.19.3.7.1.1.6.16 | ScalarmodemAdmSnmpAccessIpNetworkMask8 | read-write | current | This object is used to configure SNMP Access Network Address Mask #8. |
| 1.3.6.1.4.1.161.19.3.7.1.1.6.17 | ScalarmodemAdmSnmpAccessIpNetwork9 | read-write | current | This object is used to configure SNMP Access Network Address #9. |
| 1.3.6.1.4.1.161.19.3.7.1.1.6.18 | ScalarmodemAdmSnmpAccessIpNetworkMask9 | read-write | current | This object is used to configure SNMP Access Network Address Mask #9. |
| 1.3.6.1.4.1.161.19.3.7.1.1.6.19 | ScalarmodemAdmSnmpAccessIpNetwork10 | read-write | current | This object is used to configure SNMP Access Network Address #10. |
| 1.3.6.1.4.1.161.19.3.7.1.1.6.20 | ScalarmodemAdmSnmpAccessIpNetworkMask10 | read-write | current | This object is used to configure SNMP Access Network Address Mask #10. |
| 1.3.6.1.4.1.161.19.3.7.1.1.7 | NodewhispPlvModemAdmRepeaterConfig | |||
| 1.3.6.1.4.1.161.19.3.7.1.1.7.1 | ScalarmodemAdmRepeaterConfOperatingMode | read-write | current | This object is used to configure the Modem operating mode. Modem should be rebooted for the change in the configuration to take effect. |
| 1.3.6.1.4.1.161.19.3.7.1.1.7.2 | ScalarmodemAdmRepeaterConfModemMAC1 | read-write | current | This object represents the MAC Address of Modem 1, that uses the Repeater. |
| 1.3.6.1.4.1.161.19.3.7.1.1.7.3 | ScalarmodemAdmRepeaterConfModemMAC2 | read-write | current | This object represents the MAC Address of Modem 2, that uses the Repeater. |
| 1.3.6.1.4.1.161.19.3.7.1.1.7.4 | ScalarmodemAdmRepeaterConfModemMAC3 | read-write | current | This object represents the MAC Address of Modem 3, that uses the Repeater. |
| 1.3.6.1.4.1.161.19.3.7.1.1.7.5 | ScalarmodemAdmRepeaterConfModemMAC4 | read-write | current | This object represents the MAC Address of Modem 4, that uses the Repeater. |
| 1.3.6.1.4.1.161.19.3.7.1.1.8 | TablewhispPlvModemAdmVLANTable | not-accessible | current | This table contains one row per device connected behind the Modem, either directly OR using a switch |
| 1.3.6.1.4.1.161.19.3.7.1.1.8.1 | RowwhispPlvModemAdmVLANEntry | not-accessible | current | VLAN information of the device connected behind the Modem. |
| 1.3.6.1.4.1.161.19.3.7.1.1.8.1.1 | ColumnmodemAdmVLANIndex | not-accessible | current | The value of this object identifies the index to this entry. |
| 1.3.6.1.4.1.161.19.3.7.1.1.8.1.2 | ColumnmodemAdmVLANPhysAddress | read-only | current | This object indicates the MAC Address of the device connected behind the Modem. |
| 1.3.6.1.4.1.161.19.3.7.1.1.8.1.3 | ColumnmodemAdmVLANId | read-write | current | This object indicates the VLAN ID of the device connected behind the Modem. |
| 1.3.6.1.4.1.161.19.3.7.1.2 | NodewhispPlvModemEvents | |||
| 1.3.6.1.4.1.161.19.3.7.1.2.0 | NodemodemTrapPrefix | |||
| 1.3.6.1.4.1.161.19.3.7.1.2.0.1 | NotificationmodemTrapDeviceUpgradeStarted | current | This Notification is generated if the Modem has started the firmware Upgrade process. | |
| 1.3.6.1.4.1.161.19.3.7.1.2.0.2 | NotificationmodemTrapDeviceUpgradeCompleted | current | This Notification is generated once the Upgrade process is completed. | |
| 1.3.6.1.4.1.161.19.3.7.1.2.0.3 | NotificationmodemTrapSimUpgradeStarted | current | This Notification is generated if the Intellon Simple Module Upgrade process is started. | |
| 1.3.6.1.4.1.161.19.3.7.1.2.0.4 | NotificationmodemTrapSimUpgradeCompleted | current | This Notification is generated once the Simple Module Upgrade process is completed. | |
| 1.3.6.1.4.1.161.19.3.7.1.3 | NodewhispPlvModemConformance | |||
| 1.3.6.1.4.1.161.19.3.7.1.3.1 | NodewhispPlvModemGroups | |||
| 1.3.6.1.4.1.161.19.3.7.1.3.1.1 | GroupwhispPlvModemInfoGroup | current | The collection of objects that gives Modem device information. | |
| 1.3.6.1.4.1.161.19.3.7.1.3.1.2 | GroupwhispPlvModemConfigGroup | current | The collection of objects used to configure the Modem. These objects are accessible to everyone. | |
| 1.3.6.1.4.1.161.19.3.7.1.3.1.3 | GroupwhispPlvModemTrapConfigGroup | current | The collection of Modems SNMP Trap Configuration objects. These objects are accessible to everyone. | |
| 1.3.6.1.4.1.161.19.3.7.1.3.1.4 | GroupwhispPlvModemAdmConfigGroup | current | The collection of objects that are used to configure the Modem. These objects are accessible only thru 'admin' community string. | |
| 1.3.6.1.4.1.161.19.3.7.1.3.1.5 | GroupwhispPlvModemAdmWConfigGroup | current | The collection of Modems WAN Configuration objects. These objects are accessible only thru 'admin' community string. | |
| 1.3.6.1.4.1.161.19.3.7.1.3.1.6 | GroupwhispPlvModemAdmSnmpAcessConfigGroup | current | The collection of Modems SNMP Access Network objects. These objects are accessible only thru 'admin' community string. | |
| 1.3.6.1.4.1.161.19.3.7.1.3.1.7 | GroupwhispPlvModemNotificationsGroup | current | The collection of Notifications generated by the Modem. | |
| 1.3.6.1.4.1.161.19.3.7.1.3.1.8 | GroupwhispPlvModemAdmRepeaterConfigGroup | current | The collection of Repeater Configuration Objects. These objects are accessible only thru 'admin' community string. | |
| 1.3.6.1.4.1.161.19.3.7.1.3.1.9 | GroupwhispPlvModemAdmVLANConfigGroup | current | The collection of VLAN Configuration Objects. These objects are accessible only thru 'admin' community string. | |
| 1.3.6.1.4.1.161.19.3.7.1.3.2 | NodewhispPlvModemCompliances | |||
| 1.3.6.1.4.1.161.19.3.7.1.3.2.1 | CompliancewhispPlvModemCompliance | current | The compliance statement of SNMP entities which implement the WHISP-PLV-MODEM-MIB. |