WebGraph-2xThermometer-US-MIB
260 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC-1212 | OBJECT-TYPE |
| RFC-1215 | TRAP-TYPE |
| RFC1155-SMI | enterprises IpAddress NetworkAddress TimeTicks |
| RFC1213-MIB | DisplayString PhysAddress |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.5040 | Nodewut | |||
| 1.3.6.1.4.1.5040.1 | NodewtComServer | |||
| 1.3.6.1.4.1.5040.1.2 | NodewtWebio | |||
| 1.3.6.1.4.1.5040.1.2.43 | NodewtWebioAn2Graph | |||
| 1.3.6.1.4.1.5040.1.2.43.1 | NodewtWebioAn2GraphTemp | |||
| 1.3.6.1.4.1.5040.1.2.43.1.1 | ScalarwtWebioAn2GraphSensors | read-only | mandatory | Number of temperature sensors |
| 1.3.6.1.4.1.5040.1.2.43.1.2 | TablewtWebioAn2GraphSensorTable | not-accessible | mandatory | List of sensors. |
| 1.3.6.1.4.1.5040.1.2.43.1.2.1 | RowwtWebioAn2GraphSensorEntry | not-accessible | mandatory | Temperature sensor numbers. |
| 1.3.6.1.4.1.5040.1.2.43.1.2.1.1 | ColumnwtWebioAn2GraphSensorNo | read-only | mandatory | Temperature sensor number. |
| 1.3.6.1.4.1.5040.1.2.43.1.3 | TablewtWebioAn2GraphTempValueTable | not-accessible | mandatory | List of temperature values corresponding to the channel numbers. |
| 1.3.6.1.4.1.5040.1.2.43.1.3.1 | RowwtWebioAn2GraphTempValueEntry | not-accessible | mandatory | Temperatures of the sensors. |
| 1.3.6.1.4.1.5040.1.2.43.1.3.1.1 | ColumnwtWebioAn2GraphTempValue | read-only | mandatory | Temperature value of the sensor, ASCII, 5 characters in length. |
| 1.3.6.1.4.1.5040.1.2.43.1.4 | TablewtWebioAn2GraphBinaryTempValueTable | not-accessible | mandatory | List of binary temperature values corresponding to the channel numbers. |
| 1.3.6.1.4.1.5040.1.2.43.1.4.1 | RowwtWebioAn2GraphBinaryTempValueEntry | not-accessible | mandatory | Binary temperature values of the sensors. |
| 1.3.6.1.4.1.5040.1.2.43.1.4.1.1 | ColumnwtWebioAn2GraphBinaryTempValue | read-only | mandatory | Binary temperature value of the sensor in 1/10 degrees Celsius, signed number, 0x4FFF6 indicates an invalid measured value. |
| 1.3.6.1.4.1.5040.1.2.43.1.8 | TablewtWebioAn2GraphTempValuePktTable | not-accessible | mandatory | List of temperature values corresponding to the channel numbers. |
| 1.3.6.1.4.1.5040.1.2.43.1.8.1 | RowwtWebioAn2GraphTempValuePktEntry | not-accessible | mandatory | Temperatures of the sensors. |
| 1.3.6.1.4.1.5040.1.2.43.1.8.1.1 | ColumnwtWebioAn2GraphTempValuePkt | read-only | mandatory | Temperature value of the sensor, ASCII, 5 characters in length, decimal point. |
| 1.3.6.1.4.1.5040.1.2.43.2 | NodewtWebioAn2GraphSessCntrl | |||
| 1.3.6.1.4.1.5040.1.2.43.2.1 | ScalarwtWebioAn2GraphSessCntrlPassword | read-write | mandatory | Entering this password opens a session which is ended by writing a 1 to wtWebioAn2GraphSessCntrlLogout. When read this variable provides a string of length zer… |
| 1.3.6.1.4.1.5040.1.2.43.2.2 | ScalarwtWebioAn2GraphSessCntrlConfigMode | read-only | mandatory | When the device is in SNMP configuration mode, the value 1 is returned, otherwise 0. If the read value is 0 even though the password was written, the device is… |
| 1.3.6.1.4.1.5040.1.2.43.2.3 | ScalarwtWebioAn2GraphSessCntrlLogout | read-write | mandatory | If the device is in configuration mode and the session was opened by this SNMP Manager, writing a 1 to this variable will end the session and all parameters ar… |
| 1.3.6.1.4.1.5040.1.2.43.2.4 | ScalarwtWebioAn2GraphSessCntrlAdminPassword | read-write | mandatory | This password protects access to the variables with administrator rights. It can only be changed by the administrator. If no password was assigned, the valid p… |
| 1.3.6.1.4.1.5040.1.2.43.2.5 | ScalarwtWebioAn2GraphSessCntrlConfigPassword | read-write | mandatory | This password protects access to the variables with configurator rights. It can be changed by the administrator and by the configurator. If no password was ass… |
| 1.3.6.1.4.1.5040.1.2.43.3 | NodewtWebioAn2GraphConfig | |||
| 1.3.6.1.4.1.5040.1.2.43.3.1 | NodewtWebioAn2GraphDevice | |||
| 1.3.6.1.4.1.5040.1.2.43.3.1.1 | NodewtWebioAn2GraphText | |||
| 1.3.6.1.4.1.5040.1.2.43.3.1.1.1 | ScalarwtWebioAn2GraphDeviceName | read-write | mandatory | Name of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.1.2 | ScalarwtWebioAn2GraphDeviceText | read-write | mandatory | Description of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.1.3 | ScalarwtWebioAn2GraphDeviceLocation | read-write | mandatory | Description of the location of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.1.4 | ScalarwtWebioAn2GraphDeviceContact | read-write | mandatory | Contact address of the system operator of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.2 | NodewtWebioAn2GraphTimeDate | |||
| 1.3.6.1.4.1.5040.1.2.43.3.1.2.1 | NodewtWebioAn2GraphTimeZone | |||
| 1.3.6.1.4.1.5040.1.2.43.3.1.2.1.1 | ScalarwtWebioAn2GraphTzOffsetHrs | read-write | mandatory | Offset hours for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.2.1.2 | ScalarwtWebioAn2GraphTzOffsetMin | read-write | mandatory | Offset minutes for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.2.1.3 | ScalarwtWebioAn2GraphTzEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Timezone |
| 1.3.6.1.4.1.5040.1.2.43.3.1.2.1.4 | ScalarwtWebioAn2GraphStTzOffsetHrs | read-write | mandatory | Offset hours of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.2.1.5 | ScalarwtWebioAn2GraphStTzOffsetMin | read-write | mandatory | Offset minutes of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.2.1.6 | ScalarwtWebioAn2GraphStTzEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Summertime |
| 1.3.6.1.4.1.5040.1.2.43.3.1.2.1.7 | ScalarwtWebioAn2GraphStTzStartMonth | read-write | mandatory | Month in which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.2.1.8 | ScalarwtWebioAn2GraphStTzStartMode | read-write | mandatory | Mode of the day of the week for which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.2.1.9 | ScalarwtWebioAn2GraphStTzStartWday | read-write | mandatory | Day of the week on which the change is made from winter time to summer time |
| 1.3.6.1.4.1.5040.1.2.43.3.1.2.1.10 | ScalarwtWebioAn2GraphStTzStartHrs | read-write | mandatory | Hour in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.2.1.11 | ScalarwtWebioAn2GraphStTzStartMin | read-write | mandatory | Minute in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.2.1.12 | ScalarwtWebioAn2GraphStTzStopMonth | read-write | mandatory | Month in which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.2.1.13 | ScalarwtWebioAn2GraphStTzStopMode | read-write | mandatory | Mode of the week day on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.2.1.14 | ScalarwtWebioAn2GraphStTzStopWday | read-write | mandatory | Day of the week on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.2.1.15 | ScalarwtWebioAn2GraphStTzStopHrs | read-write | mandatory | Hour at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.2.1.16 | ScalarwtWebioAn2GraphStTzStopMin | read-write | mandatory | Minute at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.2.2 | NodewtWebioAn2GraphTimeServer | |||
| 1.3.6.1.4.1.5040.1.2.43.3.1.2.2.1 | ScalarwtWebioAn2GraphTimeServer1 | read-write | mandatory | IP address or name of the 1st time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.43.3.1.2.2.2 | ScalarwtWebioAn2GraphTimeServer2 | read-write | mandatory | IP address or name of the 2nd time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.43.3.1.2.2.3 | ScalarwtWebioAn2GraphTsEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Time Server |
| 1.3.6.1.4.1.5040.1.2.43.3.1.2.2.4 | ScalarwtWebioAn2GraphTsSyncTime | read-write | mandatory | Daily synchronisation time with the time server (hour: 0-23). |
| 1.3.6.1.4.1.5040.1.2.43.3.1.2.3 | NodewtWebioAn2GraphDeviceClock | |||
| 1.3.6.1.4.1.5040.1.2.43.3.1.2.3.1 | ScalarwtWebioAn2GraphClockHrs | read-write | mandatory | Clock hours taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.2.3.2 | ScalarwtWebioAn2GraphClockMin | read-write | mandatory | Clock minutes taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.2.3.3 | ScalarwtWebioAn2GraphClockDay | read-write | mandatory | Date: Day of the month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.2.3.4 | ScalarwtWebioAn2GraphClockMonth | read-write | mandatory | Date: Month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.2.3.5 | ScalarwtWebioAn2GraphClockYear | read-write | mandatory | Date: Year, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3 | NodewtWebioAn2GraphBasic | |||
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.1 | NodewtWebioAn2GraphNetwork | |||
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.1.1 | ScalarwtWebioAn2GraphIpAddress | read-write | mandatory | IP address of the Webio |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.1.2 | ScalarwtWebioAn2GraphSubnetMask | read-write | mandatory | Subnet mask of the Webio |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.1.3 | ScalarwtWebioAn2GraphGateway | read-write | mandatory | Gateway of the Webio |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.1.4 | ScalarwtWebioAn2GraphDnsServer1 | read-write | mandatory | IP address of the 1st DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.1.5 | ScalarwtWebioAn2GraphDnsServer2 | read-write | mandatory | IP address of the 2nd DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.1.6 | ScalarwtWebioAn2GraphAddConfig | read-write | mandatory | Additional configuration (1=ON): Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: BOOTP disable Bit 1: DHCP disable |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.2 | NodewtWebioAn2GraphHTTP | |||
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.2.1 | ScalarwtWebioAn2GraphStartup | read-write | mandatory | Binary coded start page: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1: Index.htm Bit 2: Home.htm Bit 3: User.htm Only one page may be selecte… |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.2.2 | ScalarwtWebioAn2GraphGetHeaderEnable | read-write | mandatory | If these bits are set, every answer of a short form GET question will be lead by the IP-address and name of the device and/or a HTTP header: Octet 1: unused Oc… |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.2.3 | ScalarwtWebioAn2GraphHttpPort | read-write | mandatory | Definition of the standard HTML port (Default: 80). |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.3 | NodewtWebioAn2GraphMail | |||
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.3.1 | ScalarwtWebioAn2GraphMailAdName | read-write | mandatory | Device name for mail administration. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.3.2 | ScalarwtWebioAn2GraphMailReply | read-write | mandatory | Reply address for the mail server. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.3.3 | ScalarwtWebioAn2GraphMailServer | read-write | mandatory | Name or IP address of the mail server. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.3.4 | ScalarwtWebioAn1MailEnable | read-write | mandatory | Set this bit to enable the sending of mails: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Mail enable |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.3.5 | ScalarwtWebioAn2GraphMailAuthentication | read-write | mandatory | Selection of the authentication modi: The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds to the LSB. OCTET 1: u… |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.3.6 | ScalarwtWebioAn2GraphMailAuthUser | read-write | mandatory | Name of the user to be authenticated. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.3.7 | ScalarwtWebioAn2GraphMailAuthPassword | read-write | mandatory | Authentication password. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.3.8 | ScalarwtWebioAn2GraphMailPop3Server | read-write | mandatory | Name or Ip-address of the POP3 Servers. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.4 | NodewtWebioAn2GraphSNMP | |||
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.4.1 | ScalarwtWebioAn2GraphSnmpCommunityStringRead | read-write | mandatory | Community string read only |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.4.2 | ScalarwtWebioAn2GraphSnmpCommunityStringReadWrite | read-write | mandatory | Community string read / write |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.4.3 | ScalarwtWebioAn2GraphSystemTrapManagerIP | read-write | mandatory | Name or IP address of the TCP server which accepts the system trap. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.4.4 | ScalarwtWebioAn2GraphSystemTrapEnable | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2-7: unused |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.4.5 | ScalarwtWebioAn2GraphSnmpEnable | read-write | mandatory | Set bit 0 to enable SNMP. If disabled, the device did not respond to any SNMP requests. Bit 1 decided wether the community string of read operations is compare… |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.4.6 | ScalarwtWebioAn2GraphSnmpCommunityStringTrap | read-write | mandatory | Community string send within traps. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.4.7 | ScalarwtWebioAn2GraphSnmpSystemTrapManagerPort | read-write | mandatory | Port number of the TCP server which accepts the system trap. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.5 | NodewtWebioAn2GraphUDP | |||
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.5.1 | ScalarwtWebioAn2GraphUdpPort | read-write | mandatory | Udp port to which the Udp queries ( short form GET requests) can be sent. This port number must be unique within the device. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.5.2 | ScalarwtWebioAn2GraphUdpEnable | read-write | mandatory | Set this bit to enable UDP support: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : UDP enable |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.6 | NodewtWebioAn2GraphSyslog | |||
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.6.1 | ScalarwtWebioAn2GraphSyslogServerIP | read-write | mandatory | Name or IP address of the Syslog server, which accepts the Syslog messgaes. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.6.2 | ScalarwtWebioAn2GraphSyslogServerPort | read-write | mandatory | Portnumber of the Syslog servers, default 514. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.6.3 | ScalarwtWebioAn2GraphSyslogSystemMessagesEnable | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2: Diag Messages Bit 3-7: unused |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.6.4 | ScalarwtWebioAn2GraphSyslogEnable | read-write | mandatory | Set bit 0 to enable Syslog: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Syslog enable |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.7 | NodewtWebioAn2GraphFTP | |||
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.7.1 | ScalarwtWebioAn2GraphFTPServerIP | read-write | mandatory | Name or IP address of the FTP server, which accepts the FTP messages. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.7.2 | ScalarwtWebioAn2GraphFTPServerControlPort | read-write | mandatory | Portnumber of the control port of the FTP server, default 21. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.7.3 | ScalarwtWebioAn2GraphFTPUserName | read-write | mandatory | FTP Loggin: user name. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.7.4 | ScalarwtWebioAn2GraphFTPPassword | read-write | mandatory | FTP Loggin: user password. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.7.5 | ScalarwtWebioAn2GraphFTPAccount | read-write | mandatory | FTP Loggin: name of account. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.7.6 | ScalarwtWebioAn2GraphFTPOption | read-write | mandatory | Bit 0 switches the FTP Server in Passiv-Mode, the Client controls the data connection on its own: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit … |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.7.7 | ScalarwtWebioAn2GraphFTPEnable | read-write | mandatory | Set Bit 0 to enable FTP: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : FTP enable |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.9 | NodewtWebioAn2GraphLanguage | |||
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.9.1 | ScalarwtWebioAn2GraphLanguageSelect | read-write | mandatory | Language selection: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 2-7: unused Bit 1 : English Bit 0 : German |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.12 | NodewtWebioAn2GraphMQTT | |||
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.12.1 | ScalarwtWebioAn2GraphMQTTEnable | read-write | mandatory | Bit 7 schaltet MQTT frei: Octet 1: ungenutzt Octet 2: ungenutzt Octet 3: ungenutzt Octet 4: Bit 0-6: ungenutzt Bit 7 : MQTT enable |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.12.2 | ScalarwtWebioAn2GraphMQTTBrockerIP | read-write | mandatory | Name or IP-address of the MQTT-Server. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.12.3 | ScalarwtWebioAn2GraphMQTTUserName | read-write | mandatory | MQTT login user name. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.12.4 | ScalarwtWebioAn2GraphMQTTPassword | read-write | mandatory | MQTT login password. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.12.5 | ScalarwtWebioAn2GraphMQTTLocalPort | read-write | mandatory | Local port number. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.12.6 | ScalarwtWebioAn2GraphMQTTBrokerServerPort | read-write | mandatory | MQTT Server port number. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.12.7 | ScalarwtWebioAn2GraphMQTTInterval | read-write | mandatory | Ping intervall, if no data has to be send: time in seconds. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.12.8 | ScalarwtWebioAn2GraphMQTTLastWillEnable | read-write | mandatory | Bit 0 activate MQTT LastWill message: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : MQTT Last will enable |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.12.9 | ScalarwtWebioAn2GraphMQTTLastWillTopic | read-write | mandatory | MQTT Last Will Topic. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.12.10 | ScalarwtWebioAn2GraphMQTTLastWillMsg | read-write | mandatory | MQTT Last Will message. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.12.11 | ScalarwtWebioAn2GraphMQTTLastWillQoS | read-write | mandatory | Binary coded MQTT Publish QoS: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: QoS 0 Bit 1: QoS 1 Bit 2: QoS 2 Bit 3-7:unused |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.12.12 | ScalarwtWebioAn2GraphMQTTLastWillRetain | read-write | mandatory | Binary coded MQTT Publish Retain properties: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0 : retain enable Bit 1-7 : unused |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.12.13 | ScalarwtWebioAn2GraphMQTTLastWillConnectEnable | read-write | mandatory | Bit 0 activate MQTT LastWill Connect message: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : MQTT Last will connect message e… |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.12.14 | ScalarwtWebioAn2GraphMQTTLastWillConnectMsg | read-write | mandatory | MQTT Last Will Connect message will be send with the QoS and Retain settings of the LastWill message. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.13 | NodewtWebioAn2GraphREST | |||
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.13.1 | ScalarwtWebioAn2GraphRESTEnable | read-write | mandatory | Bit 0 activates REST : Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : REST enable |
| 1.3.6.1.4.1.5040.1.2.43.3.1.3.13.2 | ScalarwtWebioAn2GraphRESTDigestAuthEnable | read-write | mandatory | Bit 0 activates Digest-Authentification: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Digest Auth enable |
| 1.3.6.1.4.1.5040.1.2.43.3.1.4 | NodewtWebioAn2GraphDatalogger | |||
| 1.3.6.1.4.1.5040.1.2.43.3.1.4.1 | ScalarwtWebioAn2GraphLoggerTimebase | read-write | mandatory | Time base of the data logger |
| 1.3.6.1.4.1.5040.1.2.43.3.1.4.2 | ScalarwtWebioAn2GraphLoggerSensorSel | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Sensor 1 Bit 1: Sensor 2 Bit 2: Sensor 3 Bit 3: Sensor 4 Bit 4… |
| 1.3.6.1.4.1.5040.1.2.43.3.1.4.3 | ScalarwtWebioAn2GraphDisplaySensorSel | read-write | mandatory | Binary coded sensor selection: only selected sensors will be shown in the graphical presentation: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit … |
| 1.3.6.1.4.1.5040.1.2.43.3.1.4.4 | TablewtWebioAn2GraphSensorColorTable | not-accessible | mandatory | List of sensor colors for the praphical presentation. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.4.4.1 | RowwtWebioAn2GraphSensorColorEntry | not-accessible | mandatory | Index numbers of the sensors. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.4.4.1.1 | ColumnwtWebioAn2GraphSensorColor | read-write | mandatory | Color of the sensors at the praphical presention. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.4.5 | ScalarwtWebioAn2GraphAutoScaleEnable | read-write | mandatory | If bit 0 is set, vertical auto scale is enabled: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Auto Scale enable |
| 1.3.6.1.4.1.5040.1.2.43.3.1.4.6 | ScalarwtWebioAn2GraphVerticalUpperLimit | read-write | mandatory | This value defines the maximum temperature shown in the graphical presentation, if no auto scaling is selected. Temperature in degrees with maximum 2 decimal p… |
| 1.3.6.1.4.1.5040.1.2.43.3.1.4.7 | ScalarwtWebioAn2GraphVerticalLowerLimit | read-write | mandatory | This value defines the minimum temperature shown in the graphical presentation, if no auto scaling is selected. Temperature in degrees with maximum 2 decimal p… |
| 1.3.6.1.4.1.5040.1.2.43.3.1.4.8 | ScalarwtWebioAn2GraphHorizontalZoom | read-write | mandatory | Defines the default zoom stage, if no auto scaling is selected. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5 | NodewtWebioAn2GraphAlarm | |||
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.1 | ScalarwtWebioAn2GraphAlarmCount | read-only | mandatory | Number of independent alarms. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.2 | TablewtWebioAn2GraphAlarmIfTable | not-accessible | mandatory | List of alarm indices. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.2.1 | RowwtWebioAn2GraphAlarmIfEntry | not-accessible | mandatory | Numbers of the alarms. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.2.1.1 | ColumnwtWebioAn2GraphAlarmNo | read-only | mandatory | Alarm number. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3 | TablewtWebioAn2GraphAlarmTable | not-accessible | mandatory | List of settings depending on the alarm number. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1 | RowwtWebioAn2GraphAlarmEntry | not-accessible | mandatory | Alarm parameters of the individual alarms. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.1 | ColumnwtWebioAn2GraphAlarmTrigger | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: Bit 0: Timer Bit 1: ColdStart Bit 2: WarmStart Octet 4: Bit 0: Sensor 1 Bit 1: Sensor… |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.2 | ColumnwtWebioAn2GraphAlarmMin | read-write | mandatory | Minimum temperature in degrees with maximum 2 decimal places. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.3 | ColumnwtWebioAn2GraphAlarmMax | read-write | mandatory | Maximum temperature in degrees with maximum 2 decimal places. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.4 | ColumnwtWebioAn2GraphAlarmHysteresis | read-write | mandatory | Temperature changes of this size clears the alarm state (MAX-hyst, MIN+hyst.) , in degrees with maximum 2 decimal places. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.5 | ColumnwtWebioAn2GraphAlarmDelay | read-write | mandatory | Alarm will be delayed by setting this time while stable alarm condition occur (time in minutes). |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.6 | ColumnwtWebioAn2GraphAlarmInterval | read-write | mandatory | Send interval for alarm messages. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.7 | ColumnwtWebioAn2GraphAlarmEnable | read-write | mandatory | Binary coded alarm enable: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Mail Enable Bit 1: SNMP Trap enable Bit 2: TCP Client enable |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.8 | ColumnwtWebioAn2GraphAlarmEMailAddr | read-write | mandatory | E-Mail address for sending the alarm mail to. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.9 | ColumnwtWebioAn2GraphAlarmMailSubject | read-write | mandatory | Subject line for alarm mail. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.10 | ColumnwtWebioAn2GraphAlarmMailText | read-write | mandatory | Alarm mail text: <Tn> provides the current temperature; n = 1..2. <Z> provides the current time. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.11 | ColumnwtWebioAn2GraphAlarmManagerIP | read-write | mandatory | Name or IP address of the SNMP Manager which accepts the trap. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.12 | ColumnwtWebioAn2GraphAlarmTrapText | read-write | mandatory | This text is sent in the trap body. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.13 | ColumnwtWebioAn2GraphAlarmMailOptions | read-write | mandatory | Binary coded options: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0 : Attach Thermo.csv Enable Bit 1 : CSV-Data_since_last_report Bit 2-7: unu… |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.14 | ColumnwtWebioAn2GraphAlarmTcpIpAddr | read-write | mandatory | Name or IP address of the TCP server which accepts the trap. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.15 | ColumnwtWebioAn2GraphAlarmTcpPort | read-write | mandatory | Port number of the TCP server which accepts the trap. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.16 | ColumnwtWebioAn2GraphAlarmTcpText | read-write | mandatory | This text is sent in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.17 | ColumnwtWebioAn2GraphAlarmClearMailSubject | read-write | mandatory | Subject line for alarm clear mail. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.18 | ColumnwtWebioAn2GraphAlarmClearMailText | read-write | mandatory | Alarm clear mail text: <Tn> provides the current temperature; n = 1..2. <Z> provides the current time. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.19 | ColumnwtWebioAn2GraphAlarmClearTrapText | read-write | mandatory | This text is sent in the trap body. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.20 | ColumnwtWebioAn2GraphAlarmClearTcpText | read-write | mandatory | This text is sent in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.21 | ColumnwtWebioAn2GraphAlarmSyslogIpAddr | read-write | mandatory | IP address of the syslog server to which the Webio device should send syslog messages. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.22 | ColumnwtWebioAn2GraphAlarmSyslogPort | read-write | mandatory | Port number of the syslog server to which the Webio device should send syslog messages. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.23 | ColumnwtWebioAn2GraphAlarmSyslogText | read-write | mandatory | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.24 | ColumnwtWebioAn2GraphAlarmSyslogClearText | read-write | mandatory | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.25 | ColumnwtWebioAn2GraphAlarmFtpDataPort | read-write | mandatory | Local data port: 1..65535 or AUTO: the next free port will be assigned. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.26 | ColumnwtWebioAn2GraphAlarmFtpFileName | read-write | mandatory | Name of the file including path informations. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.27 | ColumnwtWebioAn2GraphAlarmFtpText | read-write | mandatory | Message text to store on the FTP server. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.28 | ColumnwtWebioAn2GraphAlarmFtpClearText | read-write | mandatory | Alarm clear message to store on the FTP server. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.29 | ColumnwtWebioAn2GraphAlarmFtpOption | read-write | mandatory | Binary coded options, select only one option at the same time: STORE = replace file APPEND = append message at the end of the file Octet 1: unused Octet 2: unu… |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.30 | ColumnwtWebioAn2GraphAlarmTimerCron | read-write | mandatory | This entry contains 5 text fields space or tab seperated for time trigger definition. Each field must match with the actual time to trigger a message, weekday … |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.39 | ColumnwtWebioAn2GraphAlarmName | read-write | mandatory | Alert name |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.40 | ColumnwtWebioAn2GraphAlarmActive | read-write | mandatory | Alert active 1 = ON 0 = OFF |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.61 | ColumnwtWebioAn2GraphAlarmHttpReqAuthEnable | read-write | mandatory | Binary coded options, select only one option at the same time: OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bit 1-7: unused Bit 0 : HHTP Request Au… |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.62 | ColumnwtWebioAn2GraphAlarmHttpReqAuthUser | read-write | mandatory | HTTP Request: User |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.63 | ColumnwtWebioAn2GraphAlarmHttpReqAuthPassword | read-write | mandatory | HTTP Request: Password |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.64 | ColumnwtWebioAn2GraphAlarmHttpReqSetUrl | read-write | mandatory | HTTP Request: Set URL |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.65 | ColumnwtWebioAn2GraphAlarmHttpReqClearUrl | read-write | mandatory | HTTP Request: Clear URL |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.66 | ColumnwtWebioAn2GraphAlarmHttpReqServerPort | read-write | mandatory | HTTP Request: Server Port |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.67 | ColumnwtWebioAn2GraphAlarmMqttTopicPath | read-write | mandatory | MQTT Publish: Topic path |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.68 | ColumnwtWebioAn2GraphAlarmMqttTopicSetTopic | read-write | mandatory | MQTT Publish: Topic SET message |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.69 | ColumnwtWebioAn2GraphAlarmMqttTopicClear | read-write | mandatory | MQTT Publish: Topic CLEAR message |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.70 | ColumnwtWebioAn2GraphAlarmSensorLostSelection | read-write | mandatory | Binary coded options: OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 2-7: unused Bit 1 : Sensor 1 Bit 0 : Sensor 0 |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.71 | ColumnwtWebioAn2GraphAlarmLimitWindow | read-write | mandatory | If window type is INSIDE the alarm is genereted when the temperature is greater minumum value and lower than maximum value. If window type is OUTSIDE the alarm… |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.76 | ColumnwtWebioAn2GraphAlarmSnmpManagerPort | read-write | mandatory | Port number of the SNMP Manager to which the Webio device should send SNMP traps. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.77 | ColumnwtWebioAn2GraphAlarmMqttQoS | read-write | mandatory | Binary coded value: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: QoS 0 Bit 1: QoS 1 Bit 2: QoS 2 Bit 3-7:unused |
| 1.3.6.1.4.1.5040.1.2.43.3.1.5.3.1.78 | ColumnwtWebioAn2GraphAlarmMqttRetain | read-write | mandatory | Binary coded value: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0 : retain enable Bit 1-7 : unused |
| 1.3.6.1.4.1.5040.1.2.43.3.1.6 | NodewtWebioAn2GraphGraphics | |||
| 1.3.6.1.4.1.5040.1.2.43.3.1.6.1 | NodewtWebioAn2GraphGraphicsBase | |||
| 1.3.6.1.4.1.5040.1.2.43.3.1.6.1.1 | ScalarwtWebioAn2GraphGraphicsBaseEnable | read-write | mandatory | Defines the viewing options of the graphic: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0 : Auto scroll enable Bit 1 : Show table Bit 2 : Show… |
| 1.3.6.1.4.1.5040.1.2.43.3.1.6.1.2 | ScalarwtWebioAn2GraphGraphicsBaseWidth | read-write | mandatory | Defines the width of the graphic in pixels. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.6.1.3 | ScalarwtWebioAn2GraphGraphicsBaseHeight | read-write | mandatory | Defines the height of the graphic in pixels. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.6.1.4 | ScalarwtWebioAn2GraphGraphicsBaseFrameColor | read-write | mandatory | Frame color definition in RGB. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.6.1.5 | ScalarwtWebioAn2GraphGraphicsBaseBackgroundColor | read-write | mandatory | Background color definition in RGB. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.6.1.6 | ScalarwtWebioAn2GraphGraphicsBasePollingrate | read-write | mandatory | Defines the pollingrate in seconds, which defines the refreshing intervall of the graphic. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.6.2 | NodewtWebioAn2GraphGraphicsSelect | |||
| 1.3.6.1.4.1.5040.1.2.43.3.1.6.2.1 | ScalarwtWebioAn2GraphGraphicsSelectDisplaySensorSel | read-write | mandatory | Binary coded sensor selection: only selected sensors will be shown in the graphical presentation: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit … |
| 1.3.6.1.4.1.5040.1.2.43.3.1.6.2.2 | ScalarwtWebioAn2GraphGraphicsSelectDisplayShowExtrem | read-write | mandatory | Binary coded sensor selection: only selected sensors will be shown with minima and maxima: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Sens… |
| 1.3.6.1.4.1.5040.1.2.43.3.1.6.2.3 | TablewtWebioAn2GraphSelectSensorColorTable | not-accessible | mandatory | List of sensor colors for the praphical presentation. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.6.2.3.1 | RowwtWebioAn2GraphSelectSensorColorEntry | not-accessible | mandatory | Numbers of the sensors. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.6.2.3.1.1 | ColumnwtWebioAn2GraphSelectGraphicsSensorColor | read-write | mandatory | Color of the sensors at the praphical presention. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.6.2.3.1.2 | ColumnwtWebioAn2GraphSelectGraphicsSelectScale | read-write | mandatory | Assignes one of 4 scales to a sensor: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0 : Use Scale 1 Bit 1 : Use Scale 2 Bit 2 : Use Scale 3 Bit … |
| 1.3.6.1.4.1.5040.1.2.43.3.1.6.3 | NodewtWebioAn2GraphGraphicsScale | |||
| 1.3.6.1.4.1.5040.1.2.43.3.1.6.3.1 | ScalarwtWebioAn2GraphGraphicsScaleAutoScaleEnable | read-write | mandatory | Select the Auto Scale Mode: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0 : Scale 1 Auto scale enable Bit 1 : Scale 2 Auto scale enable Bit 2 … |
| 1.3.6.1.4.1.5040.1.2.43.3.1.6.3.2 | ScalarwtWebioAn2GraphGraphicsScaleAutoFitEnable | read-write | mandatory | Select the Auto Fit Mode:: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0 : Scale 1 Auto fit enable Bit 1 : Scale 2 Auto fit enable Bit 2 : Sca… |
| 1.3.6.1.4.1.5040.1.2.43.3.1.6.3.3 | ScalarwtWebioAn2GraphGraphicsScale1Min | read-only | mandatory | Scale 1: Minimum. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.6.3.4 | ScalarwtWebioAn2GraphGraphicsScale2Min | read-only | mandatory | Scale 2: Minimum. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.6.3.5 | ScalarwtWebioAn2GraphGraphicsScale3Min | read-only | mandatory | Scale 3: Minimum. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.6.3.6 | ScalarwtWebioAn2GraphGraphicsScale4Min | read-only | mandatory | Scale 4: Minimum. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.6.3.7 | ScalarwtWebioAn2GraphGraphicsScale1Max | read-only | mandatory | Scale 1: Maximum. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.6.3.8 | ScalarwtWebioAn2GraphGraphicsScale2Max | read-only | mandatory | Scale 2: Maximum. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.6.3.9 | ScalarwtWebioAn2GraphGraphicsScale3Max | read-only | mandatory | Scale 3: Maximum. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.6.3.10 | ScalarwtWebioAn2GraphGraphicsScale4Max | read-only | mandatory | Scale 4: Maximum. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.6.3.11 | ScalarwtWebioAn2GraphGraphicsScale1Unit | read-only | mandatory | Scale 1: Unit. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.6.3.12 | ScalarwtWebioAn2GraphGraphicsScale2Unit | read-only | mandatory | Scale 2: Unit. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.6.3.13 | ScalarwtWebioAn2GraphGraphicsScale3Unit | read-only | mandatory | Scale 3: Unit. |
| 1.3.6.1.4.1.5040.1.2.43.3.1.6.3.14 | ScalarwtWebioAn2GraphGraphicsScale4Unit | read-only | mandatory | Scale 4: Unit. |
| 1.3.6.1.4.1.5040.1.2.43.3.2 | NodewtWebioAn2GraphPorts | |||
| 1.3.6.1.4.1.5040.1.2.43.3.2.1 | TablewtWebioAn2GraphPortTable | not-accessible | mandatory | List of settings depending on the sensor number. |
| 1.3.6.1.4.1.5040.1.2.43.3.2.1.1 | RowwtWebioAn2GraphPortEntry | not-accessible | mandatory | Sensor parameters for the individual sensors. |
| 1.3.6.1.4.1.5040.1.2.43.3.2.1.1.1 | ColumnwtWebioAn2GraphPortName | read-write | mandatory | Name of the sensor. |
| 1.3.6.1.4.1.5040.1.2.43.3.2.1.1.2 | ColumnwtWebioAn2GraphPortText | read-write | mandatory | Description of the sensor. |
| 1.3.6.1.4.1.5040.1.2.43.3.2.1.1.3 | ColumnwtWebioAn2GraphPortOffset1 | read-write | mandatory | Offset calibration: Offset in degrees with maximum 2 decimal places at temperature 1. |
| 1.3.6.1.4.1.5040.1.2.43.3.2.1.1.4 | ColumnwtWebioAn2GraphPortTemperature1 | read-write | mandatory | Offset calibration: Reference temperature 1 in degrees with maximum 2 decimal places. |
| 1.3.6.1.4.1.5040.1.2.43.3.2.1.1.5 | ColumnwtWebioAn2GraphPortOffset2 | read-write | mandatory | Offset calibration: Offset in degrees with maximum 2 decimal places at temperature 2. |
| 1.3.6.1.4.1.5040.1.2.43.3.2.1.1.6 | ColumnwtWebioAn2GraphPortTemperature2 | read-write | mandatory | Offset calibration: Reference temperature 1 in degrees with maximum 2 decimal places. |
| 1.3.6.1.4.1.5040.1.2.43.3.2.1.1.7 | ColumnwtWebioAn2GraphPortComment | read-write | mandatory | Offset calibration: informations of date, name of operator, reference devices. |
| 1.3.6.1.4.1.5040.1.2.43.3.2.1.1.8 | ColumnwtWebioAn2GraphPortSensorSelect | read-write | mandatory | Bin�r kodierte Optionen f�r Sensor: Octet 1: ungenutzt Octet 2: ungenutzt Octet 3: ungenutzt Octet 4: Bit 0 : PT100 Bit 1 : PT1000 (default) Bit 2-7: ungen… |
| 1.3.6.1.4.1.5040.1.2.43.3.3 | NodewtWebioAn2GraphManufact | |||
| 1.3.6.1.4.1.5040.1.2.43.3.3.1 | ScalarwtWebioAn2GraphMfName | read-write | mandatory | Manufacturer company name |
| 1.3.6.1.4.1.5040.1.2.43.3.3.2 | ScalarwtWebioAn2GraphMfAddr | read-write | mandatory | Manufacturer address. |
| 1.3.6.1.4.1.5040.1.2.43.3.3.3 | ScalarwtWebioAn2GraphMfHotline | read-write | mandatory | Manufacturer hotline. |
| 1.3.6.1.4.1.5040.1.2.43.3.3.4 | ScalarwtWebioAn2GraphMfInternet | read-write | mandatory | Manufacturer Internet address. |
| 1.3.6.1.4.1.5040.1.2.43.3.3.5 | ScalarwtWebioAn2GraphMfDeviceTyp | read-write | mandatory | Manufacturer device name (model number). |
| 1.3.6.1.4.1.5040.1.2.43.3.3.6 | ScalarwtWebioAn2GraphMfOrderNo | read-write | mandatory | Manufacturer part number. |
| 1.3.6.1.4.1.5040.1.2.43.4 | NodewtWebioAn2GraphDiag | |||
| 1.3.6.1.4.1.5040.1.2.43.4.1 | ScalarwtWebioAn2GraphDiagErrorCount | read-only | mandatory | Number of entries in the error memory. |
| 1.3.6.1.4.1.5040.1.2.43.4.2 | ScalarwtWebioAn2GraphDiagBinaryError | read-only | mandatory | Error causes coded bit-by-bit. |
| 1.3.6.1.4.1.5040.1.2.43.4.3 | ScalarwtWebioAn2GraphDiagErrorIndex | read-write | mandatory | The value of this variable is used as an index to read an error massege from wtWebioAn2GraphDiagErrorMessage. Errors are numbered from 1 to wtWebioAn2GraphDiag… |
| 1.3.6.1.4.1.5040.1.2.43.4.4 | ScalarwtWebioAn2GraphDiagErrorMessage | read-only | mandatory | Using wtWebioAn2GraphDiagErrorIndex as an index, the appropriate message is available. |
| 1.3.6.1.4.1.5040.1.2.43.4.5 | ScalarwtWebioAn2GraphDiagErrorClear | write-only | mandatory | Writing 1 into this variable clears all diagnosis messages. |
| 1.3.6.1.4.1.5040.1.2.43.21 | NodewtWebioAn2GraphAlert1 | This SNMP trap is generated when Alarm 1 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.43.22 | NodewtWebioAn2GraphAlert2 | This SNMP trap is generated when Alarm 2 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.43.23 | NodewtWebioAn2GraphAlert3 | This SNMP trap is generated when Alarm 3 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.43.24 | NodewtWebioAn2GraphAlert4 | This SNMP trap is generated when Alarm 4 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.43.25 | NodewtWebioAn2GraphAlert5 | This SNMP trap is generated when Alarm 5 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.43.26 | NodewtWebioAn2GraphAlert6 | This SNMP trap is generated when Alarm 6 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.43.27 | NodewtWebioAn2GraphAlert7 | This SNMP trap is generated when Alarm 7 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.43.28 | NodewtWebioAn2GraphAlert8 | This SNMP trap is generated when Alarm 8 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.43.81 | NodewtWebioAn2GraphAlert9 | This SNMP trap is generated when Alarm 1 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.43.82 | NodewtWebioAn2GraphAlert10 | This SNMP trap is generated when Alarm 2 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.43.83 | NodewtWebioAn2GraphAlert11 | This SNMP trap is generated when Alarm 3 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.43.84 | NodewtWebioAn2GraphAlert12 | This SNMP trap is generated when Alarm 4 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.43.85 | NodewtWebioAn2GraphAlert13 | This SNMP trap is generated when Alarm 5 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.43.86 | NodewtWebioAn2GraphAlert14 | This SNMP trap is generated when Alarm 6 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.43.87 | NodewtWebioAn2GraphAlert15 | This SNMP trap is generated when Alarm 7 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.43.88 | NodewtWebioAn2GraphAlert16 | This SNMP trap is generated when Alarm 8 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.43.110 | NodewtWebioAn2GraphAlertDiag | This SNMP trap is generated when a diagnosis/error message was triggered, SNMP trap enable is set and SNMP is enabled. |