WebGraph-OLD-Thermometer-NTC-US-MIB
219 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC-1212 | OBJECT-TYPE |
| RFC-1215 | TRAP-TYPE |
| RFC1155-SMI | enterprises IpAddress NetworkAddress TimeTicks |
| RFC1213-MIB | DisplayString PhysAddress |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.5040 | Nodewut | |||
| 1.3.6.1.4.1.5040.1 | NodewtComServer | |||
| 1.3.6.1.4.1.5040.1.2 | NodewtWebio | |||
| 1.3.6.1.4.1.5040.1.2.17.3.1.5.3.1.31 | ScalarwtWebioAn1GraphPtAlarmDeltaTemp | read-write | mandatory | Maximum rate of change degrees/min with maximum 2 decimal places. Compared with the average of a period of 5 minutes. |
| 1.3.6.1.4.1.5040.1.2.17.3.1.5.3.1.39 | ScalarwtWebioAn1GraphPtAlarmName | read-write | mandatory | Alert name |
| 1.3.6.1.4.1.5040.1.2.17.3.1.5.3.1.40 | ScalarwtWebioAn1GraphPtAlarmActive | read-write | mandatory | Alert active 1 = ON 0 = OFF |
| 1.3.6.1.4.1.5040.1.2.18 | NodewtWebioAn1GraphNtc | |||
| 1.3.6.1.4.1.5040.1.2.18.1 | NodewtWebioAn1GraphNtcTemp | |||
| 1.3.6.1.4.1.5040.1.2.18.1.1 | ScalarwtWebioAn1GraphNtcSensors | read-only | mandatory | Number of temperature sensors |
| 1.3.6.1.4.1.5040.1.2.18.1.2 | TablewtWebioAn1GraphNtcSensorTable | not-accessible | mandatory | List of sensors. |
| 1.3.6.1.4.1.5040.1.2.18.1.2.1 | RowwtWebioAn1GraphNtcSensorEntry | not-accessible | mandatory | Temperature sensor numbers. |
| 1.3.6.1.4.1.5040.1.2.18.1.2.1.1 | ColumnwtWebioAn1GraphNtcSensorNo | read-only | mandatory | Temperature sensor number. |
| 1.3.6.1.4.1.5040.1.2.18.1.3 | TablewtWebioAn1GraphNtcTempValueTable | not-accessible | mandatory | List of temperature values corresponding to the channel numbers. |
| 1.3.6.1.4.1.5040.1.2.18.1.3.1 | RowwtWebioAn1GraphNtcTempValueEntry | not-accessible | mandatory | Temperatures of the sensors. |
| 1.3.6.1.4.1.5040.1.2.18.1.3.1.1 | ColumnwtWebioAn1GraphNtcTempValue | read-only | mandatory | Temperature value of the sensor, ASCII, 5 characters in length. |
| 1.3.6.1.4.1.5040.1.2.18.1.4 | TablewtWebioAn1GraphNtcBinaryTempValueTable | not-accessible | mandatory | List of binary temperature values corresponding to the channel numbers. |
| 1.3.6.1.4.1.5040.1.2.18.1.4.1 | RowwtWebioAn1GraphNtcBinaryTempValueEntry | not-accessible | mandatory | Binary temperature values of the sensors. |
| 1.3.6.1.4.1.5040.1.2.18.1.4.1.1 | ColumnwtWebioAn1GraphNtcBinaryTempValue | read-only | mandatory | Binary temperature value of the sensor in 1/10 degrees Celsius, signed number, 0x7FFF indicates an invalid measured value. |
| 1.3.6.1.4.1.5040.1.2.18.1.8 | TablewtWebioAn1GraphNtcTempValuePktTable | not-accessible | mandatory | List of temperature values corresponding to the channel numbers. |
| 1.3.6.1.4.1.5040.1.2.18.1.8.1 | RowwtWebioAn1GraphNtcTempValuePktEntry | not-accessible | mandatory | Temperatures of the sensors. |
| 1.3.6.1.4.1.5040.1.2.18.1.8.1.1 | ColumnwtWebioAn1GraphNtcTempValuePkt | read-only | mandatory | Temperature value of the sensor, ASCII, 5 characters in length, decimal point. |
| 1.3.6.1.4.1.5040.1.2.18.2 | NodewtWebioAn1GraphNtcSessCntrl | |||
| 1.3.6.1.4.1.5040.1.2.18.2.1 | ScalarwtWebioAn1GraphNtcSessCntrlPassword | read-write | mandatory | Entering this password opens a session which is ended by writing a 1 to wtWebioAn1GraphNtcSessCntrlLogout. When read this variable provides a string of length … |
| 1.3.6.1.4.1.5040.1.2.18.2.2 | ScalarwtWebioAn1GraphNtcSessCntrlConfigMode | read-only | mandatory | When the device is in SNMP configuration mode, the value 1 is returned, otherwise 0. If the read value is 0 even though the password was written, the device is… |
| 1.3.6.1.4.1.5040.1.2.18.2.3 | ScalarwtWebioAn1GraphNtcSessCntrlLogout | read-write | mandatory | If the device is in configuration mode and the session was opened by this SNMP Manager, writing a 1 to this variable will end the session and all parameters ar… |
| 1.3.6.1.4.1.5040.1.2.18.2.4 | ScalarwtWebioAn1GraphNtcSessCntrlAdminPassword | read-write | mandatory | This password protects access to the variables with administrator rights. It can only be changed by the administrator. If no password was assigned, the valid p… |
| 1.3.6.1.4.1.5040.1.2.18.2.5 | ScalarwtWebioAn1GraphNtcSessCntrlConfigPassword | read-write | mandatory | This password protects access to the variables with configurator rights. It can be changed by the administrator and by the configurator. If no password was ass… |
| 1.3.6.1.4.1.5040.1.2.18.3 | NodewtWebioAn1GraphNtcConfig | |||
| 1.3.6.1.4.1.5040.1.2.18.3.1 | NodewtWebioAn1GraphNtcDevice | |||
| 1.3.6.1.4.1.5040.1.2.18.3.1.1 | NodewtWebioAn1GraphNtcText | |||
| 1.3.6.1.4.1.5040.1.2.18.3.1.1.1 | ScalarwtWebioAn1GraphNtcDeviceName | read-write | mandatory | Name of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.1.2 | ScalarwtWebioAn1GraphNtcDeviceText | read-write | mandatory | Description of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.1.3 | ScalarwtWebioAn1GraphNtcDeviceLocation | read-write | mandatory | Description of the location of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.1.4 | ScalarwtWebioAn1GraphNtcDeviceContact | read-write | mandatory | Contact address of the system operator of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.2 | NodewtWebioAn1GraphNtcTimeDate | |||
| 1.3.6.1.4.1.5040.1.2.18.3.1.2.1 | NodewtWebioAn1GraphNtcTimeZone | |||
| 1.3.6.1.4.1.5040.1.2.18.3.1.2.1.1 | ScalarwtWebioAn1GraphNtcTzOffsetHrs | read-write | mandatory | Offset hours for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.2.1.2 | ScalarwtWebioAn1GraphNtcTzOffsetMin | read-write | mandatory | Offset minutes for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.2.1.3 | ScalarwtWebioAn1GraphNtcTzEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Timezone |
| 1.3.6.1.4.1.5040.1.2.18.3.1.2.1.4 | ScalarwtWebioAn1GraphNtcStTzOffsetHrs | read-write | mandatory | Offset hours of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.2.1.5 | ScalarwtWebioAn1GraphNtcStTzOffsetMin | read-write | mandatory | Offset minutes of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.2.1.6 | ScalarwtWebioAn1GraphNtcStTzEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Summertime |
| 1.3.6.1.4.1.5040.1.2.18.3.1.2.1.7 | ScalarwtWebioAn1GraphNtcStTzStartMonth | read-write | mandatory | Month in which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.2.1.8 | ScalarwtWebioAn1GraphNtcStTzStartMode | read-write | mandatory | Mode of the day of the week for which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.2.1.9 | ScalarwtWebioAn1GraphNtcStTzStartWday | read-write | mandatory | Day of the week on which the change is made from winter time to summer time |
| 1.3.6.1.4.1.5040.1.2.18.3.1.2.1.10 | ScalarwtWebioAn1GraphNtcStTzStartHrs | read-write | mandatory | Hour in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.2.1.11 | ScalarwtWebioAn1GraphNtcStTzStartMin | read-write | mandatory | Minute in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.2.1.12 | ScalarwtWebioAn1GraphNtcStTzStopMonth | read-write | mandatory | Month in which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.2.1.13 | ScalarwtWebioAn1GraphNtcStTzStopMode | read-write | mandatory | Mode of the week day on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.2.1.14 | ScalarwtWebioAn1GraphNtcStTzStopWday | read-write | mandatory | Day of the week on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.2.1.15 | ScalarwtWebioAn1GraphNtcStTzStopHrs | read-write | mandatory | Hour at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.2.1.16 | ScalarwtWebioAn1GraphNtcStTzStopMin | read-write | mandatory | Minute at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.2.2 | NodewtWebioAn1GraphNtcTimeServer | |||
| 1.3.6.1.4.1.5040.1.2.18.3.1.2.2.1 | ScalarwtWebioAn1GraphNtcTimeServer1 | read-write | mandatory | IP address or name of the 1st time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.18.3.1.2.2.2 | ScalarwtWebioAn1GraphNtcTimeServer2 | read-write | mandatory | IP address or name of the 2nd time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.18.3.1.2.2.3 | ScalarwtWebioAn1GraphNtcTsEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Time Server |
| 1.3.6.1.4.1.5040.1.2.18.3.1.2.2.4 | ScalarwtWebioAn1GraphNtcTsSyncTime | read-write | mandatory | Daily synchronisation time with the time server (hour: 0-23). |
| 1.3.6.1.4.1.5040.1.2.18.3.1.2.3 | NodewtWebioAn1GraphNtcDeviceClock | |||
| 1.3.6.1.4.1.5040.1.2.18.3.1.2.3.1 | ScalarwtWebioAn1GraphNtcClockHrs | read-write | mandatory | Clock hours taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.2.3.2 | ScalarwtWebioAn1GraphNtcClockMin | read-write | mandatory | Clock minutes taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.2.3.3 | ScalarwtWebioAn1GraphNtcClockDay | read-write | mandatory | Date: Day of the month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.2.3.4 | ScalarwtWebioAn1GraphNtcClockMonth | read-write | mandatory | Date: Month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.2.3.5 | ScalarwtWebioAn1GraphNtcClockYear | read-write | mandatory | Date: Year, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.3 | NodewtWebioAn1GraphNtcBasic | |||
| 1.3.6.1.4.1.5040.1.2.18.3.1.3.1 | NodewtWebioAn1GraphNtcNetwork | |||
| 1.3.6.1.4.1.5040.1.2.18.3.1.3.1.1 | ScalarwtWebioAn1GraphNtcIpAddress | read-write | mandatory | IP address of the Webio |
| 1.3.6.1.4.1.5040.1.2.18.3.1.3.1.2 | ScalarwtWebioAn1GraphNtcSubnetMask | read-write | mandatory | Subnet mask of the Webio |
| 1.3.6.1.4.1.5040.1.2.18.3.1.3.1.3 | ScalarwtWebioAn1GraphNtcGateway | read-write | mandatory | Gateway of the Webio |
| 1.3.6.1.4.1.5040.1.2.18.3.1.3.1.4 | ScalarwtWebioAn1GraphNtcDnsServer1 | read-write | mandatory | IP address of the 1st DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.18.3.1.3.1.5 | ScalarwtWebioAn1GraphNtcDnsServer2 | read-write | mandatory | IP address of the 2nd DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.18.3.1.3.1.6 | ScalarwtWebioAn1GraphNtcAddConfig | read-write | mandatory | Additional configuration (1=ON): Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1: DHCP disable Bit 0: BOOTP disable |
| 1.3.6.1.4.1.5040.1.2.18.3.1.3.2 | NodewtWebioAn1GraphNtcHTTP | |||
| 1.3.6.1.4.1.5040.1.2.18.3.1.3.2.1 | ScalarwtWebioAn1GraphNtcStartup | read-write | mandatory | Binary coded start page: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1: Index.htm Bit 2: Home.htm Bit 3: User.htm Only one page may be selecte… |
| 1.3.6.1.4.1.5040.1.2.18.3.1.3.2.2 | ScalarwtWebioAn1GraphNtcGetHeaderEnable | read-write | mandatory | If these bits are set, every answer of a short form GET question will be lead by the IP-address and name of the device and/or a HTTP header: Octet 1: unused Oc… |
| 1.3.6.1.4.1.5040.1.2.18.3.1.3.2.3 | ScalarwtWebioAn1GraphNtcHttpPort | read-write | mandatory | Definition of the standard HTML port (Default: 80). |
| 1.3.6.1.4.1.5040.1.2.18.3.1.3.3 | NodewtWebioAn1GraphNtcMail | |||
| 1.3.6.1.4.1.5040.1.2.18.3.1.3.3.1 | ScalarwtWebioAn1GraphNtcMailAdName | read-write | mandatory | Device name for mail administration. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.3.3.2 | ScalarwtWebioAn1GraphNtcMailReply | read-write | mandatory | Reply address for the mail server. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.3.3.3 | ScalarwtWebioAn1GraphNtcMailServer | read-write | mandatory | Name or IP address of the mail server. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.3.3.4 | ScalarwtWebioAn1MailEnable | read-write | mandatory | Set this bit to enable the sending of mails: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Mail enable |
| 1.3.6.1.4.1.5040.1.2.18.3.1.3.3.5 | ScalarwtWebioAn1GraphNtcMailAuthentication | read-write | mandatory | Selection of the authentication modi: The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds to the LSB. OCTET 1: u… |
| 1.3.6.1.4.1.5040.1.2.18.3.1.3.3.6 | ScalarwtWebioAn1GraphNtcMailAuthUser | read-write | mandatory | Name of the user to be authenticated. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.3.3.7 | ScalarwtWebioAn1GraphNtcMailAuthPassword | read-write | mandatory | Authentication password. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.3.3.8 | ScalarwtWebioAn1GraphNtcMailPop3Server | read-write | mandatory | Name or Ip-address of the POP3 Servers. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.3.4 | NodewtWebioAn1GraphNtcSNMP | |||
| 1.3.6.1.4.1.5040.1.2.18.3.1.3.4.1 | ScalarwtWebioAn1GraphNtcSnmpCommunityStringRead | read-write | mandatory | Community string read only |
| 1.3.6.1.4.1.5040.1.2.18.3.1.3.4.2 | ScalarwtWebioAn1GraphNtcSnmpCommunityStringReadWrite | read-write | mandatory | Community string read / write |
| 1.3.6.1.4.1.5040.1.2.18.3.1.3.4.3 | ScalarwtWebioAn1GraphNtcSystemTrapManagerIP | read-write | mandatory | Name or IP address of the TCP server which accepts the system trap. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.3.4.4 | ScalarwtWebioAn1GraphNtcSystemTrapEnable | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2-7: unused |
| 1.3.6.1.4.1.5040.1.2.18.3.1.3.4.5 | ScalarwtWebioAn1GraphNtcSnmpEnable | read-write | mandatory | Set bit 0 to enable SNMP. If disabled, the device did not respond to any SNMP requests. Bit 1 decided wether the community string of read operations is compare… |
| 1.3.6.1.4.1.5040.1.2.18.3.1.3.4.6 | ScalarwtWebioAn1GraphNtcSnmpCommunityStringTrap | read-write | mandatory | Community string send within traps. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.3.5 | NodewtWebioAn1GraphNtcUDP | |||
| 1.3.6.1.4.1.5040.1.2.18.3.1.3.5.1 | ScalarwtWebioAn1GraphNtcUdpPort | read-write | mandatory | Udp port to which the Udp queries ( short form GET requests) can be sent. This port number must be unique within the device. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.3.5.2 | ScalarwtWebioAn1GraphNtcUdpEnable | read-write | mandatory | Set this bit to enable UDP support: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : UDP enable |
| 1.3.6.1.4.1.5040.1.2.18.3.1.3.6 | NodewtWebioAn1GraphNtcSyslog | |||
| 1.3.6.1.4.1.5040.1.2.18.3.1.3.6.1 | ScalarwtWebioAn1GraphNtcSyslogServerIP | read-write | mandatory | Name or IP address of the Syslog server, which accepts the Syslog messgaes. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.3.6.2 | ScalarwtWebioAn1GraphNtcSyslogServerPort | read-write | mandatory | Portnumber of the Syslog servers, default 514. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.3.6.3 | ScalarwtWebioAn1GraphNtcSyslogSystemMessagesEnable | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2: Diag Messages Bit 3-7: unused |
| 1.3.6.1.4.1.5040.1.2.18.3.1.3.6.4 | ScalarwtWebioAn1GraphNtcSyslogEnable | read-write | mandatory | Set bit 0 to enable Syslog: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Syslog enable |
| 1.3.6.1.4.1.5040.1.2.18.3.1.3.7 | NodewtWebioAn1GraphNtcFTP | |||
| 1.3.6.1.4.1.5040.1.2.18.3.1.3.7.1 | ScalarwtWebioAn1GraphNtcFTPServerIP | read-write | mandatory | Name or IP address of the FTP server, which accepts the FTP messages. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.3.7.2 | ScalarwtWebioAn1GraphNtcFTPServerControlPort | read-write | mandatory | Portnumber of the control port of the FTP server, default 21. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.3.7.3 | ScalarwtWebioAn1GraphNtcFTPUserName | read-write | mandatory | FTP Loggin: user name. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.3.7.4 | ScalarwtWebioAn1GraphNtcFTPPassword | read-write | mandatory | FTP Loggin: user password. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.3.7.5 | ScalarwtWebioAn1GraphNtcFTPAccount | read-write | mandatory | FTP Loggin: name of account. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.3.7.6 | ScalarwtWebioAn1GraphNtcFTPOption | read-write | mandatory | Bit 0 switches the FTP Server in Passiv-Mode, the Client controls the data connection on its own: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit … |
| 1.3.6.1.4.1.5040.1.2.18.3.1.3.7.7 | ScalarwtWebioAn1GraphNtcFTPEnable | read-write | mandatory | Set Bit 0 to enable FTP: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : FTP enable |
| 1.3.6.1.4.1.5040.1.2.18.3.1.4 | NodewtWebioAn1GraphNtcDatalogger | |||
| 1.3.6.1.4.1.5040.1.2.18.3.1.4.1 | ScalarwtWebioAn1GraphNtcLoggerTimebase | read-write | mandatory | Time base of the data logger |
| 1.3.6.1.4.1.5040.1.2.18.3.1.4.2 | ScalarwtWebioAn1GraphNtcLoggerSensorSel | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Sensor 1 Bit 1: Sensor 2 Bit 2: Sensor 3 Bit 3: Sensor 4 Bit 4… |
| 1.3.6.1.4.1.5040.1.2.18.3.1.4.3 | ScalarwtWebioAn1GraphNtcDisplaySensorSel | read-write | mandatory | Binary coded sensor selection: only selected sensors will be shown in the graphical presentation: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit … |
| 1.3.6.1.4.1.5040.1.2.18.3.1.4.4 | TablewtWebioAn1GraphNtcSensorColorTable | not-accessible | mandatory | List of sensor colors for the praphical presentation. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.4.4.1 | RowwtWebioAn1GraphNtcSensorColorEntry | not-accessible | mandatory | Index numbers of the sensors. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.4.4.1.1 | ColumnwtWebioAn1GraphNtcSensorColor | read-write | mandatory | Color of the sensors at the praphical presention. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.4.5 | ScalarwtWebioAn1GraphNtcAutoScaleEnable | read-write | mandatory | If bit 0 is set, vertical auto scale is enabled: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Auto Scale enable |
| 1.3.6.1.4.1.5040.1.2.18.3.1.4.6 | ScalarwtWebioAn1GraphNtcVerticalUpperLimit | read-write | mandatory | This value defines the maximum temperature shown in the graphical presentation, if no auto scaling is selected. Temperature in degrees with maximum 2 decimal p… |
| 1.3.6.1.4.1.5040.1.2.18.3.1.4.7 | ScalarwtWebioAn1GraphNtcVerticalLowerLimit | read-write | mandatory | This value defines the minimum temperature shown in the graphical presentation, if no auto scaling is selected. Temperature in degrees with maximum 2 decimal p… |
| 1.3.6.1.4.1.5040.1.2.18.3.1.4.8 | ScalarwtWebioAn1GraphNtcHorizontalZoom | read-write | mandatory | Defines the default zoom stage, if no auto scaling is selected. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.5 | NodewtWebioAn1GraphNtcAlarm | |||
| 1.3.6.1.4.1.5040.1.2.18.3.1.5.1 | ScalarwtWebioAn1GraphNtcAlarmCount | read-only | mandatory | Number of independent alarms. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.5.2 | TablewtWebioAn1GraphNtcAlarmIfTable | not-accessible | mandatory | List of alarm indices. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.5.2.1 | RowwtWebioAn1GraphNtcAlarmIfEntry | not-accessible | mandatory | Numbers of the alarms. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.5.2.1.1 | ColumnwtWebioAn1GraphNtcAlarmNo | read-only | mandatory | Alarm number. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.5.3 | TablewtWebioAn1GraphNtcAlarmTable | not-accessible | mandatory | List of settings depending on the alarm number. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.5.3.1 | RowwtWebioAn1GraphNtcAlarmEntry | not-accessible | mandatory | Alarm parameters of the individual alarms. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.5.3.1.1 | ColumnwtWebioAn1GraphNtcAlarmTrigger | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: Bit 0: Timer Bit 1: ColdStart Bit 2: WarmStart Octet 4: Bit 0: Sensor 1 Bit 1: Sensor… |
| 1.3.6.1.4.1.5040.1.2.18.3.1.5.3.1.2 | ColumnwtWebioAn1GraphNtcAlarmMin | read-write | mandatory | Minimum temperature in degrees with maximum 2 decimal places. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.5.3.1.3 | ColumnwtWebioAn1GraphNtcAlarmMax | read-write | mandatory | Maximum temperature in degrees with maximum 2 decimal places. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.5.3.1.4 | ColumnwtWebioAn1GraphNtcAlarmHysteresis | read-write | mandatory | Temperature changes of this size clears the alarm state (MAX-hyst, MIN+hyst.) , in degrees with maximum 2 decimal places. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.5.3.1.5 | ColumnwtWebioAn1GraphNtcAlarmDelay | read-write | mandatory | Alarm will be delayed by setting this time while stable alarm condition occur (time in minutes). |
| 1.3.6.1.4.1.5040.1.2.18.3.1.5.3.1.6 | ColumnwtWebioAn1GraphNtcAlarmInterval | read-write | mandatory | Send interval for alarm messages. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.5.3.1.7 | ColumnwtWebioAn1GraphNtcAlarmEnable | read-write | mandatory | Binary coded alarm enable: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Mail Enable Bit 1: SNMP Trap enable Bit 2: TCP Client enable |
| 1.3.6.1.4.1.5040.1.2.18.3.1.5.3.1.8 | ColumnwtWebioAn1GraphNtcAlarmEMailAddr | read-write | mandatory | E-Mail address for sending the alarm mail to. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.5.3.1.9 | ColumnwtWebioAn1GraphNtcAlarmMailSubject | read-write | mandatory | Subject line for alarm mail. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.5.3.1.10 | ColumnwtWebioAn1GraphNtcAlarmMailText | read-write | mandatory | Alarm mail text: <Tn> provides the current temperature; n = 1..8. <Z> provides the current time. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.5.3.1.11 | ColumnwtWebioAn1GraphNtcAlarmManagerIP | read-write | mandatory | Name or IP address of the SNMP Manager which accepts the trap. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.5.3.1.12 | ColumnwtWebioAn1GraphNtcAlarmTrapText | read-write | mandatory | This text is sent in the trap body. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.5.3.1.13 | ColumnwtWebioAn1GraphNtcAlarmMailOptions | read-write | mandatory | Binary coded options: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0 : Attach Thermo.csv Enable Bit 1 : CSV-Data_since_last_report Bit 2-7: unu… |
| 1.3.6.1.4.1.5040.1.2.18.3.1.5.3.1.14 | ColumnwtWebioAn1GraphNtcAlarmTcpIpAddr | read-write | mandatory | Name or IP address of the TCP server which accepts the trap. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.5.3.1.15 | ColumnwtWebioAn1GraphNtcAlarmTcpPort | read-write | mandatory | Port number of the TCP server which accepts the trap. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.5.3.1.16 | ColumnwtWebioAn1GraphNtcAlarmTcpText | read-write | mandatory | This text is sent in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.5.3.1.17 | ColumnwtWebioAn1GraphNtcAlarmClearMailSubject | read-write | mandatory | Subject line for alarm clear mail. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.5.3.1.18 | ColumnwtWebioAn1GraphNtcAlarmClearMailText | read-write | mandatory | Alarm clear mail text: <Tn> provides the current temperature; n = 1..8. <Z> provides the current time. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.5.3.1.19 | ColumnwtWebioAn1GraphNtcAlarmClearTrapText | read-write | mandatory | This text is sent in the trap body. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.5.3.1.20 | ColumnwtWebioAn1GraphNtcAlarmClearTcpText | read-write | mandatory | This text is sent in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.5.3.1.21 | ColumnwtWebioAn1GraphNtcAlarmSyslogIpAddr | read-write | mandatory | IP address of the syslog server to which the Webio device should send syslog messages. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.5.3.1.22 | ColumnwtWebioAn1GraphNtcAlarmSyslogPort | read-write | mandatory | Port number of the syslog server to which the Webio device should send syslog messages. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.5.3.1.23 | ColumnwtWebioAn1GraphNtcAlarmSyslogText | read-write | mandatory | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.5.3.1.24 | ColumnwtWebioAn1GraphNtcAlarmSyslogClearText | read-write | mandatory | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.5.3.1.25 | ColumnwtWebioAn1GraphNtcAlarmFtpDataPort | read-write | mandatory | Local data port: 1..65535 or AUTO: the next free port will be assigned. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.5.3.1.26 | ColumnwtWebioAn1GraphNtcAlarmFtpFileName | read-write | mandatory | Name of the file including path informations. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.5.3.1.27 | ColumnwtWebioAn1GraphNtcAlarmFtpText | read-write | mandatory | Message text to store on the FTP server. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.5.3.1.28 | ColumnwtWebioAn1GraphNtcAlarmFtpClearText | read-write | mandatory | Alarm clear message to store on the FTP server. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.5.3.1.29 | ColumnwtWebioAn1GraphNtcAlarmFtpOption | read-write | mandatory | Binary coded options, select only one option at the same time: STORE = replace file APPEND = append message at the end of the file Octet 1: unused Octet 2: unu… |
| 1.3.6.1.4.1.5040.1.2.18.3.1.5.3.1.30 | ColumnwtWebioAn1GraphNtcAlarmTimerCron | read-write | mandatory | This entry contains 5 text fields space or tab seperated for time trigger definition. Each field must match with the actual time to trigger a message, weekday … |
| 1.3.6.1.4.1.5040.1.2.18.3.1.6 | NodewtWebioAn1GraphNtcGraphics | |||
| 1.3.6.1.4.1.5040.1.2.18.3.1.6.1 | NodewtWebioAn1GraphNtcGraphicsBase | |||
| 1.3.6.1.4.1.5040.1.2.18.3.1.6.1.1 | ScalarwtWebioAn1GraphNtcGraphicsBaseEnable | read-write | mandatory | Defines the viewing options of the graphic: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0 : Auto scroll enable Bit 1 : Show table Bit 2 : Show… |
| 1.3.6.1.4.1.5040.1.2.18.3.1.6.1.2 | ScalarwtWebioAn1GraphNtcGraphicsBaseWidth | read-write | mandatory | Defines the width of the graphic in pixels. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.6.1.3 | ScalarwtWebioAn1GraphNtcGraphicsBaseHeight | read-write | mandatory | Defines the height of the graphic in pixels. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.6.1.4 | ScalarwtWebioAn1GraphNtcGraphicsBaseFrameColor | read-write | mandatory | Frame color definition in RGB. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.6.1.5 | ScalarwtWebioAn1GraphNtcGraphicsBaseBackgroundColor | read-write | mandatory | Background color definition in RGB. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.6.1.6 | ScalarwtWebioAn1GraphNtcGraphicsBasePollingrate | read-write | mandatory | Defines the pollingrate in seconds, which defines the refreshing intervall of the graphic. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.6.2 | NodewtWebioAn1GraphNtcGraphicsSelect | |||
| 1.3.6.1.4.1.5040.1.2.18.3.1.6.2.1 | ScalarwtWebioAn1GraphNtcGraphicsSelectDisplaySensorSel | read-write | mandatory | Binary coded sensor selection: only selected sensors will be shown in the graphical presentation: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit … |
| 1.3.6.1.4.1.5040.1.2.18.3.1.6.2.2 | ScalarwtWebioAn1GraphNtcGraphicsSelectDisplayShowExtrem | read-write | mandatory | Binary coded sensor selection: only selected sensors will be shown with minima and maxima: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0 : Sen… |
| 1.3.6.1.4.1.5040.1.2.18.3.1.6.2.3 | TablewtWebioAn1GraphNtc2SensorColorTable | not-accessible | mandatory | List of sensor colors for the praphical presentation. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.6.2.3.1 | RowwtWebioAn1GraphNtc2SensorColorEntry | not-accessible | mandatory | Numbers of the sensors. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.6.2.3.1.1 | ColumnwtWebioAn1GraphNtcGraphicsSensorColor | read-write | mandatory | Color of the sensors at the praphical presention. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.6.2.3.1.2 | ColumnwtWebioAn1GraphNtcGraphicsSelectScale | read-write | mandatory | Assignes one of 4 scales to a sensor: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0 : Use Scale 1 Bit 1-7: unused |
| 1.3.6.1.4.1.5040.1.2.18.3.1.6.3 | NodewtWebioAn1GraphNtcGraphicsScale | |||
| 1.3.6.1.4.1.5040.1.2.18.3.1.6.3.1 | ScalarwtWebioAn1GraphNtcGraphicsScaleAutoScaleEnable | read-write | mandatory | Select the Auto Scale Mode: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0 : Scale 1 Auto scale enable Bit 1-7: unused |
| 1.3.6.1.4.1.5040.1.2.18.3.1.6.3.2 | ScalarwtWebioAn1GraphNtcGraphicsScaleAutoFitEnable | read-write | mandatory | Select the Auto Fit Mode:: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0 : Scale 1 Auto fit enable Bit 1-7: unused |
| 1.3.6.1.4.1.5040.1.2.18.3.1.6.3.3 | ScalarwtWebioAn1GraphNtcGraphicsScale1Min | read-only | mandatory | Scale 1: Minimum. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.6.3.4 | ScalarwtWebioAn1GraphNtcGraphicsScale2Min | read-only | mandatory | Scale 2: Minimum. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.6.3.5 | ScalarwtWebioAn1GraphNtcGraphicsScale3Min | read-only | mandatory | Scale 3: Minimum. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.6.3.6 | ScalarwtWebioAn1GraphNtcGraphicsScale4Min | read-only | mandatory | Scale 4: Minimum. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.6.3.7 | ScalarwtWebioAn1GraphNtcGraphicsScale1Max | read-only | mandatory | Scale 1: Maximum. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.6.3.8 | ScalarwtWebioAn1GraphNtcGraphicsScale2Max | read-only | mandatory | Scale 2: Maximum. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.6.3.9 | ScalarwtWebioAn1GraphNtcGraphicsScale3Max | read-only | mandatory | Scale 3: Maximum. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.6.3.10 | ScalarwtWebioAn1GraphNtcGraphicsScale4Max | read-only | mandatory | Scale 4: Maximum. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.6.3.11 | ScalarwtWebioAn1GraphNtcGraphicsScale1Unit | read-only | mandatory | Scale 1: Unit. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.6.3.12 | ScalarwtWebioAn1GraphNtcGraphicsScale2Unit | read-only | mandatory | Scale 2: Unit. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.6.3.13 | ScalarwtWebioAn1GraphNtcGraphicsScale3Unit | read-only | mandatory | Scale 3: Unit. |
| 1.3.6.1.4.1.5040.1.2.18.3.1.6.3.14 | ScalarwtWebioAn1GraphNtcGraphicsScale4Unit | read-only | mandatory | Scale 4: Unit. |
| 1.3.6.1.4.1.5040.1.2.18.3.2 | NodewtWebioAn1GraphNtcPorts | |||
| 1.3.6.1.4.1.5040.1.2.18.3.2.1 | TablewtWebioAn1GraphNtcPortTable | not-accessible | mandatory | List of settings depending on the sensor number. |
| 1.3.6.1.4.1.5040.1.2.18.3.2.1.1 | RowwtWebioAn1GraphNtcPortEntry | not-accessible | mandatory | Sensor parameters for the individual sensors. |
| 1.3.6.1.4.1.5040.1.2.18.3.2.1.1.1 | ColumnwtWebioAn1GraphNtcPortName | read-write | mandatory | Name of the sensor. |
| 1.3.6.1.4.1.5040.1.2.18.3.2.1.1.2 | ColumnwtWebioAn1GraphNtcPortText | read-write | mandatory | Description of the sensor. |
| 1.3.6.1.4.1.5040.1.2.18.3.2.1.1.3 | ColumnwtWebioAn1GraphNtcPortOffset1 | read-write | mandatory | Offset calibration: Offset in degrees with maximum 2 decimal places at temperature 1. |
| 1.3.6.1.4.1.5040.1.2.18.3.2.1.1.4 | ColumnwtWebioAn1GraphNtcPortTemperature1 | read-write | mandatory | Offset calibration: Reference temperature 1 in degrees with maximum 2 decimal places. |
| 1.3.6.1.4.1.5040.1.2.18.3.2.1.1.5 | ColumnwtWebioAn1GraphNtcPortOffset2 | read-write | mandatory | Offset calibration: Offset in degrees with maximum 2 decimal places at temperature 2. |
| 1.3.6.1.4.1.5040.1.2.18.3.2.1.1.6 | ColumnwtWebioAn1GraphNtcPortTemperature2 | read-write | mandatory | Offset calibration: Reference temperature 1 in degrees with maximum 2 decimal places. |
| 1.3.6.1.4.1.5040.1.2.18.3.2.1.1.7 | ColumnwtWebioAn1GraphNtcPortComment | read-write | mandatory | Offset calibration: informations of date, name of operator, reference devices. |
| 1.3.6.1.4.1.5040.1.2.18.3.3 | NodewtWebioAn1GraphNtcManufact | |||
| 1.3.6.1.4.1.5040.1.2.18.3.3.1 | ScalarwtWebioAn1GraphNtcMfName | read-write | mandatory | Manufacturer company name |
| 1.3.6.1.4.1.5040.1.2.18.3.3.2 | ScalarwtWebioAn1GraphNtcMfAddr | read-write | mandatory | Manufacturer address. |
| 1.3.6.1.4.1.5040.1.2.18.3.3.3 | ScalarwtWebioAn1GraphNtcMfHotline | read-write | mandatory | Manufacturer hotline. |
| 1.3.6.1.4.1.5040.1.2.18.3.3.4 | ScalarwtWebioAn1GraphNtcMfInternet | read-write | mandatory | Manufacturer Internet address. |
| 1.3.6.1.4.1.5040.1.2.18.3.3.5 | ScalarwtWebioAn1GraphNtcMfDeviceTyp | read-write | mandatory | Manufacturer device name (model number). |
| 1.3.6.1.4.1.5040.1.2.18.3.3.6 | ScalarwtWebioAn1GraphNtcMfOrderNo | read-write | mandatory | Manufacturer part number. |
| 1.3.6.1.4.1.5040.1.2.18.31 | NodewtWebioAn1GraphNtcAlert1 | This SNMP trap is generated when Alarm 1 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.18.32 | NodewtWebioAn1GraphNtcAlert2 | This SNMP trap is generated when Alarm 2 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.18.33 | NodewtWebioAn1GraphNtcAlert3 | This SNMP trap is generated when Alarm 3 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.18.34 | NodewtWebioAn1GraphNtcAlert4 | This SNMP trap is generated when Alarm 4 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.18.35 | NodewtWebioAn1GraphNtcAlert5 | This SNMP trap is generated when Alarm 5 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.18.36 | NodewtWebioAn1GraphNtcAlert6 | This SNMP trap is generated when Alarm 6 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.18.37 | NodewtWebioAn1GraphNtcAlert7 | This SNMP trap is generated when Alarm 7 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.18.38 | NodewtWebioAn1GraphNtcAlert8 | This SNMP trap is generated when Alarm 8 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.18.91 | NodewtWebioAn1GraphNtcAlert9 | This SNMP trap is generated when Alarm 1 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.18.92 | NodewtWebioAn1GraphNtcAlert10 | This SNMP trap is generated when Alarm 2 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.18.93 | NodewtWebioAn1GraphNtcAlert11 | This SNMP trap is generated when Alarm 3 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.18.94 | NodewtWebioAn1GraphNtcAlert12 | This SNMP trap is generated when Alarm 4 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.18.95 | NodewtWebioAn1GraphNtcAlert13 | This SNMP trap is generated when Alarm 5 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.18.96 | NodewtWebioAn1GraphNtcAlert14 | This SNMP trap is generated when Alarm 6 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.18.97 | NodewtWebioAn1GraphNtcAlert15 | This SNMP trap is generated when Alarm 7 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.18.98 | NodewtWebioAn1GraphNtcAlert16 | This SNMP trap is generated when Alarm 8 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.18.110 | NodewtWebioAn1GraphNtcAlertDiag | This SNMP trap is generated when a diagnosis/error message was triggered, SNMP trap enable is set and SNMP is enabled. |