Webio-ANx-MIB
417 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC-1212 | OBJECT-TYPE |
| RFC-1215 | TRAP-TYPE |
| RFC1155-SMI | enterprises IpAddress NetworkAddress TimeTicks |
| RFC1213-MIB | DisplayString PhysAddress |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.5040 | Nodewut | |||
| 1.3.6.1.4.1.5040.1 | NodewtComServer | |||
| 1.3.6.1.4.1.5040.1.2 | NodewtWebio | |||
| 1.3.6.1.4.1.5040.1.2.1 | NodewtWebioAn8 | |||
| 1.3.6.1.4.1.5040.1.2.1.1 | NodewtWebioAn8Temp | |||
| 1.3.6.1.4.1.5040.1.2.1.1.1 | ScalarwtWebioAn8Sensors | read-only | mandatory | Number of temperature sensors |
| 1.3.6.1.4.1.5040.1.2.1.1.2 | TablewtWebioAn8SensorTable | not-accessible | mandatory | List of sensors. |
| 1.3.6.1.4.1.5040.1.2.1.1.2.1 | RowwtWebioAn8SensorEntry | not-accessible | mandatory | Temperature sensor numbers. |
| 1.3.6.1.4.1.5040.1.2.1.1.2.1.1 | ColumnwtWebioAn8SensorNo | read-only | mandatory | Temperature sensor number. |
| 1.3.6.1.4.1.5040.1.2.1.1.3 | TablewtWebioAn8TempValueTable | not-accessible | mandatory | List of temperature values corresponding to the channel numbers. |
| 1.3.6.1.4.1.5040.1.2.1.1.3.1 | RowwtWebioAn8TempValueEntry | not-accessible | mandatory | Temperatures of the sensors. |
| 1.3.6.1.4.1.5040.1.2.1.1.3.1.1 | ColumnwtWebioAn8TempValue | read-only | mandatory | Temperature value of the sensor, ASCII, 5 characters in length. |
| 1.3.6.1.4.1.5040.1.2.1.1.4 | TablewtWebioAn8BinaryTempValueTable | not-accessible | mandatory | List of binary temperature values corresponding to the channel numbers. |
| 1.3.6.1.4.1.5040.1.2.1.1.4.1 | RowwtWebioAn8BinaryTempValueEntry | not-accessible | mandatory | Binary temperature values of the sensors. |
| 1.3.6.1.4.1.5040.1.2.1.1.4.1.1 | ColumnwtWebioAn8BinaryTempValue | read-only | mandatory | Binary temperature value of the sensor in 1/10 degrees Celsius, signed number, 0x7FFF indicates an invalid measured value. |
| 1.3.6.1.4.1.5040.1.2.1.2 | NodewtWebioAn8SessCntrl | |||
| 1.3.6.1.4.1.5040.1.2.1.2.1 | ScalarwtWebioAn8SessCntrlPassword | read-write | mandatory | Entering this password opens a session which is ended by writing a 1 to wtWebioAn8SessCntrlLogout. When read this variable provides a string of length zero. |
| 1.3.6.1.4.1.5040.1.2.1.2.2 | ScalarwtWebioAn8SessCntrlConfigMode | read-only | mandatory | When the device is in SNMP configuration mode, the value 1 is returned, otherwise 0. If the read value is 0 even though the password was written, the device is… |
| 1.3.6.1.4.1.5040.1.2.1.2.3 | ScalarwtWebioAn8SessCntrlLogout | read-write | mandatory | If the device is in configuration mode and the session was opened by this SNMP Manager, writing a 1 to this variable will end the session and all parameters ar… |
| 1.3.6.1.4.1.5040.1.2.1.2.4 | ScalarwtWebioAn8SessCntrlAdminPassword | read-write | mandatory | This password protects access to the variables with administrator rights. It can only be changed by the administrator. If no password was assigned, the valid p… |
| 1.3.6.1.4.1.5040.1.2.1.2.5 | ScalarwtWebioAn8SessCntrlConfigPassword | read-write | mandatory | This password protects access to the variables with configurator rights. It can be changed by the administrator and by the configurator. If no password was ass… |
| 1.3.6.1.4.1.5040.1.2.1.3 | NodewtWebioAn8Config | |||
| 1.3.6.1.4.1.5040.1.2.1.3.1 | NodewtWebioAn8Device | |||
| 1.3.6.1.4.1.5040.1.2.1.3.1.1 | NodewtWebioAn8Network | |||
| 1.3.6.1.4.1.5040.1.2.1.3.1.1.1 | ScalarwtWebioAn8IpAddress | read-write | mandatory | IP address of the Webio |
| 1.3.6.1.4.1.5040.1.2.1.3.1.1.2 | ScalarwtWebioAn8SubnetMask | read-write | mandatory | Subnet mask of the Webio |
| 1.3.6.1.4.1.5040.1.2.1.3.1.1.3 | ScalarwtWebioAn8Gateway | read-write | mandatory | Gateway of the Webio |
| 1.3.6.1.4.1.5040.1.2.1.3.1.1.4 | ScalarwtWebioAn8DnsServer1 | read-write | mandatory | IP address of the 1st DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.1.3.1.1.5 | ScalarwtWebioAn8DnsServer2 | read-write | mandatory | IP address of the 2nd DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.1.3.1.1.6 | ScalarwtWebioAn8AddConfig | read-write | mandatory | Additional configuration (1=ON): Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: BOOTP disable |
| 1.3.6.1.4.1.5040.1.2.1.3.1.2 | NodewtWebioAn8Text | |||
| 1.3.6.1.4.1.5040.1.2.1.3.1.2.1 | ScalarwtWebioAn8DeviceName | read-write | mandatory | Name of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.2.2 | ScalarwtWebioAn8DeviceText | read-write | mandatory | Description of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.2.3 | ScalarwtWebioAn8DeviceLocation | read-write | mandatory | Description of the location of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.2.4 | ScalarwtWebioAn8DeviceContact | read-write | mandatory | Contact address of the system operator of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.3 | NodewtWebioAn8TimeDate | |||
| 1.3.6.1.4.1.5040.1.2.1.3.1.3.1 | NodewtWebioAn8TimeZone | |||
| 1.3.6.1.4.1.5040.1.2.1.3.1.3.1.1 | ScalarwtWebioAn8TzName | read-write | mandatory | Name of the time zone (winter time). |
| 1.3.6.1.4.1.5040.1.2.1.3.1.3.1.2 | ScalarwtWebioAn8TzOffsetHrs | read-write | mandatory | Offset hours for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.3.1.3 | ScalarwtWebioAn8TzOffsetMin | read-write | mandatory | Offset minutes for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.3.1.4 | ScalarwtWebioAn8StTzName | read-write | mandatory | Name of the time zone (summer time). |
| 1.3.6.1.4.1.5040.1.2.1.3.1.3.1.5 | ScalarwtWebioAn8StTzOffsetHrs | read-write | mandatory | Offset hours of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.3.1.6 | ScalarwtWebioAn8StTzOffsetMin | read-write | mandatory | Offset minutes of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.3.1.7 | ScalarwtWebioAn8StTzStartMonth | read-write | mandatory | Month in which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.3.1.8 | ScalarwtWebioAn8StTzStartMode | read-write | mandatory | Mode of the day of the week for which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.3.1.9 | ScalarwtWebioAn8StTzStartWday | read-write | mandatory | Day of the week on which the change is made from winter time to summer time |
| 1.3.6.1.4.1.5040.1.2.1.3.1.3.1.10 | ScalarwtWebioAn8StTzStartHrs | read-write | mandatory | Hour in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.3.1.11 | ScalarwtWebioAn8StTzStartMin | read-write | mandatory | Minute in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.3.1.12 | ScalarwtWebioAn8StTzStopMonth | read-write | mandatory | Month in which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.3.1.13 | ScalarwtWebioAn8StTzStopMode | read-write | mandatory | Mode of the week day on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.3.1.14 | ScalarwtWebioAn8StTzStopWday | read-write | mandatory | Day of the week on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.3.1.15 | ScalarwtWebioAn8StTzStopHrs | read-write | mandatory | Hour at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.3.1.16 | ScalarwtWebioAn8StTzStopMin | read-write | mandatory | Minute at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.3.2 | NodewtWebioAn8TimeServer | |||
| 1.3.6.1.4.1.5040.1.2.1.3.1.3.2.1 | ScalarwtWebioAn8TimeServer1 | read-write | mandatory | IP address or name of the 1st time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.1.3.1.3.2.2 | ScalarwtWebioAn8TimeServer2 | read-write | mandatory | IP address or name of the 2nd time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.1.3.1.3.3 | NodewtWebioAn8DeviceClock | |||
| 1.3.6.1.4.1.5040.1.2.1.3.1.3.3.1 | ScalarwtWebioAn8ClockHrs | read-write | mandatory | Clock hours taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.3.3.2 | ScalarwtWebioAn8ClockMin | read-write | mandatory | Clock minutes taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.3.3.3 | ScalarwtWebioAn8ClockDay | read-write | mandatory | Date: Day of the month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.3.3.4 | ScalarwtWebioAn8ClockMonth | read-write | mandatory | Date: Month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.3.3.5 | ScalarwtWebioAn8ClockYear | read-write | mandatory | Date: Year, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.4 | NodewtWebioAn8MailAdmin | |||
| 1.3.6.1.4.1.5040.1.2.1.3.1.4.1 | ScalarwtWebioAn8MailAdName | read-write | mandatory | Device name for mail administration. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.4.2 | ScalarwtWebioAn8MailReply | read-write | mandatory | Reply address for the mail server. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.4.3 | ScalarwtWebioAn8MailServer | read-write | mandatory | Name or IP address of the mail server. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.5 | NodewtWebioAn8Alarm | |||
| 1.3.6.1.4.1.5040.1.2.1.3.1.5.1 | ScalarwtWebioAn8AlarmCount | read-only | mandatory | Number of independent alarms. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.5.2 | TablewtWebioAn8AlarmIfTable | not-accessible | mandatory | List of alarm indices. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.5.2.1 | RowwtWebioAn8AlarmIfEntry | not-accessible | mandatory | Numbers of the alarms. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.5.2.1.1 | ColumnwtWebioAn8AlarmNo | read-only | mandatory | Alarm number. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.5.3 | TablewtWebioAn8AlarmTable | not-accessible | mandatory | List of settings depending on the alarm number. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.5.3.1 | RowwtWebioAn8AlarmEntry | not-accessible | mandatory | Alarm parameters of the individual alarms. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.5.3.1.1 | ColumnwtWebioAn8AlarmTrigger | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: Bit 0: Timer Bit 1: ColdStart Bit 2: WarmStart Octet 4: Bit 0: Sensor 1 Bit 1: Sensor… |
| 1.3.6.1.4.1.5040.1.2.1.3.1.5.3.1.2 | ColumnwtWebioAn8AlarmMin | read-write | mandatory | Minimum temperature in degrees with maximum 2 decimal places. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.5.3.1.3 | ColumnwtWebioAn8AlarmMax | read-write | mandatory | Maximum temperature in degrees with maximum 2 decimal places. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.5.3.1.4 | ColumnwtWebioAn8AlarmInterval | read-write | mandatory | Send interval for alarm messages. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.5.3.1.5 | ColumnwtWebioAn8AlarmEnable | read-write | mandatory | Binary coded alarm enable: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Mail Enable Bit 1: SNMP Trap enable Bit 2: TCP Client enable |
| 1.3.6.1.4.1.5040.1.2.1.3.1.5.3.1.6 | ColumnwtWebioAn8AlarmEMailAddr | read-write | mandatory | E-Mail address for sending the alarm mail to. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.5.3.1.7 | ColumnwtWebioAn8AlarmMailSubject | read-write | mandatory | Subject line for alarm mail. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.5.3.1.8 | ColumnwtWebioAn8AlarmMailText | read-write | mandatory | Alarm mail text: <Tn> provides the current temperature; n = 1..8. <Z> provides the current time. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.5.3.1.9 | ColumnwtWebioAn8AlarmManagerIP | read-write | mandatory | Name or IP address of the SNMP Manager which accepts the trap. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.5.3.1.10 | ColumnwtWebioAn8AlarmTrapText | read-write | mandatory | This text is sent in the trap body. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.5.3.1.11 | ColumnwtWebioAn8AlarmMailOptions | read-write | mandatory | Binary coded options: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0 : Attach Thermo.csv Enable Bit 1-7: unused |
| 1.3.6.1.4.1.5040.1.2.1.3.1.5.3.1.12 | ColumnwtWebioAn8AlarmTcpIpAddr | read-write | mandatory | Name or IP address of the TCP server which accepts the trap. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.5.3.1.13 | ColumnwtWebioAn8AlarmTcpPort | read-write | mandatory | Port number of the TCP server which accepts the trap. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.5.3.1.14 | ColumnwtWebioAn8AlarmTcpText | read-write | mandatory | This text is sent in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.5.3.1.15 | ColumnwtWebioAn8AlarmHysteresis | read-write | mandatory | Temperature changes of this size clears the alarm state (MAX-hyst, MIN+hyst.) , in degrees with maximum 2 decimal places. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.5.3.1.16 | ColumnwtWebioAn8AlarmClearMailSubject | read-write | mandatory | Subject line for alarm clear mail. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.5.3.1.17 | ColumnwtWebioAn8AlarmClearMailText | read-write | mandatory | Alarm clear mail text: <Tn> provides the current temperature; n = 1..8. <Z> provides the current time. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.5.3.1.18 | ColumnwtWebioAn8AlarmClearTrapText | read-write | mandatory | This text is sent in the trap body. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.5.3.1.19 | ColumnwtWebioAn8AlarmClearTcpText | read-write | mandatory | This text is sent in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.6 | NodewtWebioAn8Datalogger | |||
| 1.3.6.1.4.1.5040.1.2.1.3.1.6.1 | ScalarwtWebioAn8LoggerTimebase | read-write | mandatory | Time base of the data logger |
| 1.3.6.1.4.1.5040.1.2.1.3.1.6.2 | ScalarwtWebioAn8LoggerSensorSel | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Sensor 1 Bit 1: Sensor 2 Bit 2: Sensor 3 Bit 3: Sensor 4 Bit 4… |
| 1.3.6.1.4.1.5040.1.2.1.3.1.7 | NodewtWebioAn8Protocol | |||
| 1.3.6.1.4.1.5040.1.2.1.3.1.7.1 | NodewtWebioAn8PrtclUDP | |||
| 1.3.6.1.4.1.5040.1.2.1.3.1.7.1.1 | ScalarwtWebioAn8PrtclUdpPort | read-write | mandatory | Udp port to which the Udp queries GET Single can be sent |
| 1.3.6.1.4.1.5040.1.2.1.3.1.7.2 | NodewtWebioAn8PrtclSNMP | |||
| 1.3.6.1.4.1.5040.1.2.1.3.1.7.2.1 | ScalarwtWebioAn8PrtclSnmpCommunityStringRead | read-write | mandatory | Community string read only |
| 1.3.6.1.4.1.5040.1.2.1.3.1.7.2.2 | ScalarwtWebioAn8PrtclSnmpCommunityStringReadWrite | read-write | mandatory | Community string read / write |
| 1.3.6.1.4.1.5040.1.2.1.3.1.7.2.3 | ScalarwtWebioAn8SystemTrapManagerIP | read-write | mandatory | Name or IP address of the TCP server which accepts the system trap. |
| 1.3.6.1.4.1.5040.1.2.1.3.1.7.2.4 | ScalarwtWebioAn8SystemTrapEnable | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2-7: unused |
| 1.3.6.1.4.1.5040.1.2.1.3.1.7.3 | NodewtWebioAn8PrtclHTTP | |||
| 1.3.6.1.4.1.5040.1.2.1.3.1.8 | NodewtWebioAn8Enable | |||
| 1.3.6.1.4.1.5040.1.2.1.3.1.8.1 | ScalarwtWebioAn8Enables | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Update enable Bit 1: Mail enable Bit 2: Snmp enable Bit 3: UDP… |
| 1.3.6.1.4.1.5040.1.2.1.3.1.9 | NodewtWebioAn8Startup | |||
| 1.3.6.1.4.1.5040.1.2.1.3.1.9.1 | ScalarwtWebioAn8StartupSite | read-write | mandatory | Binary coded start page: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1: Index.htm Bit 2: Home.htm Bit 3: User.htm Only one page may be selecte… |
| 1.3.6.1.4.1.5040.1.2.1.3.2 | NodewtWebioAn8Ports | |||
| 1.3.6.1.4.1.5040.1.2.1.3.2.1 | TablewtWebioAn8PortTable | not-accessible | mandatory | List of settings depending on the sensor number. |
| 1.3.6.1.4.1.5040.1.2.1.3.2.1.1 | RowwtWebioAn8PortEntry | not-accessible | mandatory | Sensor parameters for the individual sensors. |
| 1.3.6.1.4.1.5040.1.2.1.3.2.1.1.1 | ColumnwtWebioAn8PortName | read-write | mandatory | Name of the sensor. |
| 1.3.6.1.4.1.5040.1.2.1.3.2.1.1.2 | ColumnwtWebioAn8PortText | read-write | mandatory | Description of the sensor. |
| 1.3.6.1.4.1.5040.1.2.1.3.2.1.1.3 | ColumnwtWebioAn8PortOffset1 | read-write | mandatory | Offset calibration: Offset in degrees with maximum 2 decimal places at temperature 1. |
| 1.3.6.1.4.1.5040.1.2.1.3.2.1.1.4 | ColumnwtWebioAn8PortTemperature1 | read-write | mandatory | Offset calibration: Reference temperature 1 in degrees with maximum 2 decimal places. |
| 1.3.6.1.4.1.5040.1.2.1.3.2.1.1.5 | ColumnwtWebioAn8PortOffset2 | read-write | mandatory | Offset calibration: Offset in degrees with maximum 2 decimal places at temperature 2. |
| 1.3.6.1.4.1.5040.1.2.1.3.2.1.1.6 | ColumnwtWebioAn8PortTemperature2 | read-write | mandatory | Offset calibration: Reference temperature 1 in degrees with maximum 2 decimal places. |
| 1.3.6.1.4.1.5040.1.2.1.3.2.1.1.7 | ColumnwtWebioAn8PortComment | read-write | mandatory | Offset calibration: informations of date, name of operator, reference devices. |
| 1.3.6.1.4.1.5040.1.2.1.3.3 | NodewtWebioAn8Manufact | |||
| 1.3.6.1.4.1.5040.1.2.1.3.3.1 | ScalarwtWebioAn8MfName | read-write | mandatory | Manufacturer company name |
| 1.3.6.1.4.1.5040.1.2.1.3.3.2 | ScalarwtWebioAn8MfAddr | read-write | mandatory | Manufacturer address. |
| 1.3.6.1.4.1.5040.1.2.1.3.3.3 | ScalarwtWebioAn8MfHotline | read-write | mandatory | Manufacturer hotline. |
| 1.3.6.1.4.1.5040.1.2.1.3.3.4 | ScalarwtWebioAn8MfInternet | read-write | mandatory | Manufacturer Internet address. |
| 1.3.6.1.4.1.5040.1.2.1.3.3.5 | ScalarwtWebioAn8MfDeviceTyp | read-write | mandatory | Manufacturer device name (model number). |
| 1.3.6.1.4.1.5040.1.2.1.3.3.6 | ScalarwtWebioAn8MfOrderNo | read-write | mandatory | Manufacturer part number. |
| 1.3.6.1.4.1.5040.1.2.1.11 | NodewtWebioAn8Alert1 | This SNMP trap is generated when Alarm 1 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.1.12 | NodewtWebioAn8Alert2 | This SNMP trap is generated when Alarm 2 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.1.13 | NodewtWebioAn8Alert3 | This SNMP trap is generated when Alarm 3 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.1.14 | NodewtWebioAn8Alert4 | This SNMP trap is generated when Alarm 4 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.1.15 | NodewtWebioAn8Alert5 | This SNMP trap is generated when Alarm 5 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.1.16 | NodewtWebioAn8Alert6 | This SNMP trap is generated when Alarm 6 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.1.17 | NodewtWebioAn8Alert7 | This SNMP trap is generated when Alarm 7 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.1.18 | NodewtWebioAn8Alert8 | This SNMP trap is generated when Alarm 8 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.1.71 | NodewtWebioAn8Alert9 | This SNMP trap is generated when Alarm 1 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.1.72 | NodewtWebioAn8Alert10 | This SNMP trap is generated when Alarm 2 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.1.73 | NodewtWebioAn8Alert11 | This SNMP trap is generated when Alarm 3 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.1.74 | NodewtWebioAn8Alert12 | This SNMP trap is generated when Alarm 4 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.1.75 | NodewtWebioAn8Alert13 | This SNMP trap is generated when Alarm 5 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.1.76 | NodewtWebioAn8Alert14 | This SNMP trap is generated when Alarm 6 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.1.77 | NodewtWebioAn8Alert15 | This SNMP trap is generated when Alarm 7 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.1.78 | NodewtWebioAn8Alert16 | This SNMP trap is generated when Alarm 8 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.2 | NodewtWebioAn2 | |||
| 1.3.6.1.4.1.5040.1.2.2.1 | NodewtWebioAn2Temp | |||
| 1.3.6.1.4.1.5040.1.2.2.1.1 | ScalarwtWebioAn2Sensors | read-only | mandatory | Number of temperature sensors |
| 1.3.6.1.4.1.5040.1.2.2.1.2 | TablewtWebioAn2SensorTable | not-accessible | mandatory | List of Sensors. |
| 1.3.6.1.4.1.5040.1.2.2.1.2.1 | RowwtWebioAn2SensorEntry | not-accessible | mandatory | Temperature sensor numbers. |
| 1.3.6.1.4.1.5040.1.2.2.1.2.1.1 | ColumnwtWebioAn2SensorNo | read-only | mandatory | Temperature sensor number. |
| 1.3.6.1.4.1.5040.1.2.2.1.3 | TablewtWebioAn2TempValueTable | not-accessible | mandatory | List of temperature values corresponding to the channel numbers. |
| 1.3.6.1.4.1.5040.1.2.2.1.3.1 | RowwtWebioAn2TempValueEntry | not-accessible | mandatory | Temperatures of the sensors. |
| 1.3.6.1.4.1.5040.1.2.2.1.3.1.1 | ColumnwtWebioAn2TempValue | read-only | mandatory | Temperature value of the sensor, ASCII, 5 characters in length. |
| 1.3.6.1.4.1.5040.1.2.2.1.4 | TablewtWebioAn2BinaryTempValueTable | not-accessible | mandatory | List of binary temperature values corresponding to the channel numbers. |
| 1.3.6.1.4.1.5040.1.2.2.1.4.1 | RowwtWebioAn2BinaryTempValueEntry | not-accessible | mandatory | Binary temperature values of the sensors. |
| 1.3.6.1.4.1.5040.1.2.2.1.4.1.1 | ColumnwtWebioAn2BinaryTempValue | read-only | mandatory | Binary temperature value of the sensor in 1/10 degrees Celsius, signed number, 0x7FFF indicates an invalid measured value. |
| 1.3.6.1.4.1.5040.1.2.2.2 | NodewtWebioAn2SessCntrl | |||
| 1.3.6.1.4.1.5040.1.2.2.2.1 | ScalarwtWebioAn2SessCntrlPassword | read-write | mandatory | Entering this password opens a session which is ended by writing a 1 to wtWebioAn2SessCntrlLogout. When read this variable provides a string of length zero. |
| 1.3.6.1.4.1.5040.1.2.2.2.2 | ScalarwtWebioAn2SessCntrlConfigMode | read-only | mandatory | When the device is in SNMP configuration mode, the value 1 is returned, otherwise 0. If the read value is 0 even though the password was written, the device is… |
| 1.3.6.1.4.1.5040.1.2.2.2.3 | ScalarwtWebioAn2SessCntrlLogout | read-write | mandatory | If the device is in configuration mode and the session was opened by this SNMP Manager, writing a 1 to this variable will end the session and all parameters ar… |
| 1.3.6.1.4.1.5040.1.2.2.2.4 | ScalarwtWebioAn2SessCntrlAdminPassword | read-write | mandatory | This password protects access to the variables with administrator rights. It can only be changed by the administrator. If no password was assigned, the valid p… |
| 1.3.6.1.4.1.5040.1.2.2.2.5 | ScalarwtWebioAn2SessCntrlConfigPassword | read-write | mandatory | This password protects access to the variables with configurator rights. It can be changed by the administrator and by the configurator. If no password was ass… |
| 1.3.6.1.4.1.5040.1.2.2.3 | NodewtWebioAn2Config | |||
| 1.3.6.1.4.1.5040.1.2.2.3.1 | NodewtWebioAn2Device | |||
| 1.3.6.1.4.1.5040.1.2.2.3.1.1 | NodewtWebioAn2Network | |||
| 1.3.6.1.4.1.5040.1.2.2.3.1.1.1 | ScalarwtWebioAn2IpAddress | read-write | mandatory | IP address of the Webio |
| 1.3.6.1.4.1.5040.1.2.2.3.1.1.2 | ScalarwtWebioAn2SubnetMask | read-write | mandatory | ubnet mask of the Webio |
| 1.3.6.1.4.1.5040.1.2.2.3.1.1.3 | ScalarwtWebioAn2Gateway | read-write | mandatory | Gateway of the Webio |
| 1.3.6.1.4.1.5040.1.2.2.3.1.1.4 | ScalarwtWebioAn2DnsServer1 | read-write | mandatory | IP address of the 1st DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.2.3.1.1.5 | ScalarwtWebioAn2DnsServer2 | read-write | mandatory | IP address of the 2nd DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.2.3.1.1.6 | ScalarwtWebioAn2AddConfig | read-write | mandatory | Additional configuration (1=ON): Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: BOOTP disable |
| 1.3.6.1.4.1.5040.1.2.2.3.1.2 | NodewtWebioAn2Text | |||
| 1.3.6.1.4.1.5040.1.2.2.3.1.2.1 | ScalarwtWebioAn2DeviceName | read-write | mandatory | Name of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.2.2 | ScalarwtWebioAn2DeviceText | read-write | mandatory | Description of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.2.3 | ScalarwtWebioAn2DeviceLocation | read-write | mandatory | Description of the location of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.2.4 | ScalarwtWebioAn2DeviceContact | read-write | mandatory | Contact address of the system operator of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.3 | NodewtWebioAn2TimeDate | |||
| 1.3.6.1.4.1.5040.1.2.2.3.1.3.1 | NodewtWebioAn2TimeZone | |||
| 1.3.6.1.4.1.5040.1.2.2.3.1.3.1.1 | ScalarwtWebioAn2TzName | read-write | mandatory | Name of the time zone (winter time). |
| 1.3.6.1.4.1.5040.1.2.2.3.1.3.1.2 | ScalarwtWebioAn2TzOffsetHrs | read-write | mandatory | Offset hours for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.3.1.3 | ScalarwtWebioAn2TzOffsetMin | read-write | mandatory | Offset minutes for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.3.1.4 | ScalarwtWebioAn2StTzName | read-write | mandatory | Name of the time zone (summer time). |
| 1.3.6.1.4.1.5040.1.2.2.3.1.3.1.5 | ScalarwtWebioAn2StTzOffsetHrs | read-write | mandatory | Offset hours of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.3.1.6 | ScalarwtWebioAn2StTzOffsetMin | read-write | mandatory | Offset minutes of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.3.1.7 | ScalarwtWebioAn2StTzStartMonth | read-write | mandatory | Month in which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.3.1.8 | ScalarwtWebioAn2StTzStartMode | read-write | mandatory | Mode of the day of the week for which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.3.1.9 | ScalarwtWebioAn2StTzStartWday | read-write | mandatory | Day of the week on which the change is made from winter time to summer time |
| 1.3.6.1.4.1.5040.1.2.2.3.1.3.1.10 | ScalarwtWebioAn2StTzStartHrs | read-write | mandatory | Hour in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.3.1.11 | ScalarwtWebioAn2StTzStartMin | read-write | mandatory | Minute in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.3.1.12 | ScalarwtWebioAn2StTzStopMonth | read-write | mandatory | Month in which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.3.1.13 | ScalarwtWebioAn2StTzStopMode | read-write | mandatory | Mode of the week day on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.3.1.14 | ScalarwtWebioAn2StTzStopWday | read-write | mandatory | Day of the week on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.3.1.15 | ScalarwtWebioAn2StTzStopHrs | read-write | mandatory | Hour at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.3.1.16 | ScalarwtWebioAn2StTzStopMin | read-write | mandatory | Minute at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.3.2 | NodewtWebioAn2TimeServer | |||
| 1.3.6.1.4.1.5040.1.2.2.3.1.3.2.1 | ScalarwtWebioAn2TimeServer1 | read-write | mandatory | IP address or name of the 1st time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.2.3.1.3.2.2 | ScalarwtWebioAn2TimeServer2 | read-write | mandatory | IP address or name of the 2nd time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.2.3.1.3.3 | NodewtWebioAn2DeviceClock | |||
| 1.3.6.1.4.1.5040.1.2.2.3.1.3.3.1 | ScalarwtWebioAn2ClockHrs | read-write | mandatory | Clock hours taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.3.3.2 | ScalarwtWebioAn2ClockMin | read-write | mandatory | Clock minutes taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.3.3.3 | ScalarwtWebioAn2ClockDay | read-write | mandatory | Date: Day of the month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.3.3.4 | ScalarwtWebioAn2ClockMonth | read-write | mandatory | Date: Month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.3.3.5 | ScalarwtWebioAn2ClockYear | read-write | mandatory | Date: Year, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.4 | NodewtWebioAn2MailAdmin | |||
| 1.3.6.1.4.1.5040.1.2.2.3.1.4.1 | ScalarwtWebioAn2MailAdName | read-write | mandatory | Device name for mail administration. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.4.2 | ScalarwtWebioAn2MailReply | read-write | mandatory | Reply address for the mail server. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.4.3 | ScalarwtWebioAn2MailServer | read-write | mandatory | Name or IP address of the mail server. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.5 | NodewtWebioAn2Alarm | |||
| 1.3.6.1.4.1.5040.1.2.2.3.1.5.1 | ScalarwtWebioAn2AlarmCount | read-only | mandatory | Number of independent alarms. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.5.2 | TablewtWebioAn2AlarmIfTable | not-accessible | mandatory | List of alarm indices. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.5.2.1 | RowwtWebioAn2AlarmIfEntry | not-accessible | mandatory | Numbers of the alarms. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.5.2.1.1 | ColumnwtWebioAn2AlarmNo | read-only | mandatory | Alarm number. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.5.3 | TablewtWebioAn2AlarmTable | not-accessible | mandatory | List of settings depending on the alarm number. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.5.3.1 | RowwtWebioAn2AlarmEntry | not-accessible | mandatory | Alarm parameters of the individual alarms. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.5.3.1.1 | ColumnwtWebioAn2AlarmTrigger | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Sensor 1 Bit 1: Sensor 2 Bit 2: Timer Bit 1: ColdStart Bit 2: … |
| 1.3.6.1.4.1.5040.1.2.2.3.1.5.3.1.2 | ColumnwtWebioAn2AlarmMin | read-write | mandatory | Minimum temperature in degrees with maximum 2 decimal places. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.5.3.1.3 | ColumnwtWebioAn2AlarmMax | read-write | mandatory | Maximum temperature in degrees with maximum 2 decimal places. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.5.3.1.4 | ColumnwtWebioAn2AlarmInterval | read-write | mandatory | Send interval for alarm messages. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.5.3.1.5 | ColumnwtWebioAn2AlarmEnable | read-write | mandatory | Binary coded alarm enable: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Mail Enable Bit 1: SNMP Trap enable Bit 2: TCP Client enable |
| 1.3.6.1.4.1.5040.1.2.2.3.1.5.3.1.6 | ColumnwtWebioAn2AlarmEMailAddr | read-write | mandatory | E-Mail address for sending the alarm mail to. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.5.3.1.7 | ColumnwtWebioAn2AlarmMailSubject | read-write | mandatory | Subject line for alarm mail. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.5.3.1.8 | ColumnwtWebioAn2AlarmMailText | read-write | mandatory | Alarm mail text: <Tn> provides the current temperature; n = 1..2. <Z> provides the current time. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.5.3.1.9 | ColumnwtWebioAn2AlarmManagerIP | read-write | mandatory | Name or IP address of the SNMP Manager which accepts the trap. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.5.3.1.10 | ColumnwtWebioAn2AlarmTrapText | read-write | mandatory | This text is sent in the trap body. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.5.3.1.11 | ColumnwtWebioAn2AlarmMailOptions | read-write | mandatory | Binary coded options: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0 : Attach Thermo.csv Enable Bit 1-7: unused |
| 1.3.6.1.4.1.5040.1.2.2.3.1.5.3.1.12 | ColumnwtWebioAn2AlarmTcpIpAddr | read-write | mandatory | Name or IP address of the TCP server which accepts the trap. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.5.3.1.13 | ColumnwtWebioAn2AlarmTcpPort | read-write | mandatory | Port number of the TCP server which accepts the trap. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.5.3.1.14 | ColumnwtWebioAn2AlarmTcpText | read-write | mandatory | This text is sent in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.5.3.1.15 | ColumnwtWebioAn2AlarmHysteresis | read-write | mandatory | Temperature changes of this size clears the alarm state (MAX-hyst, MIN+hyst.) , in degrees with maximum 2 decimal places. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.5.3.1.16 | ColumnwtWebioAn2AlarmClearMailSubject | read-write | mandatory | Subject line for alarm clear mail. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.5.3.1.17 | ColumnwtWebioAn2AlarmClearMailText | read-write | mandatory | Alarm clear mail text: <Tn> provides the current temperature; n = 1..8. <Z> provides the current time. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.5.3.1.18 | ColumnwtWebioAn2AlarmClearTrapText | read-write | mandatory | This text is sent in the trap body. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.5.3.1.19 | ColumnwtWebioAn2AlarmClearTcpText | read-write | mandatory | This text is sent in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.6 | NodewtWebioAn2Datalogger | |||
| 1.3.6.1.4.1.5040.1.2.2.3.1.6.1 | ScalarwtWebioAn2LoggerTimebase | read-write | mandatory | Time base of the data logger |
| 1.3.6.1.4.1.5040.1.2.2.3.1.6.2 | ScalarwtWebioAn2LoggerSensorSel | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Sensor 1 Bit 1: Sensor 2 |
| 1.3.6.1.4.1.5040.1.2.2.3.1.7 | NodewtWebioAn2Protocol | |||
| 1.3.6.1.4.1.5040.1.2.2.3.1.7.1 | NodewtWebioAn2PrtclUDP | |||
| 1.3.6.1.4.1.5040.1.2.2.3.1.7.1.1 | ScalarwtWebioAn2PrtclUdpPort | read-write | mandatory | Udp port to which the Udp queries GET Single can be sent |
| 1.3.6.1.4.1.5040.1.2.2.3.1.7.2 | NodewtWebioAn2PrtclSNMP | |||
| 1.3.6.1.4.1.5040.1.2.2.3.1.7.2.1 | ScalarwtWebioAn2PrtclSnmpCommunityStringRead | read-write | mandatory | Community string read only |
| 1.3.6.1.4.1.5040.1.2.2.3.1.7.2.2 | ScalarwtWebioAn2PrtclSnmpCommunityStringReadWrite | read-write | mandatory | Community string read / write |
| 1.3.6.1.4.1.5040.1.2.2.3.1.7.2.3 | ScalarwtWebioAn2SystemTrapManagerIP | read-write | mandatory | Name or IP address of the TCP server which accepts the system trap. |
| 1.3.6.1.4.1.5040.1.2.2.3.1.7.2.4 | ScalarwtWebioAn2SystemTrapEnable | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2-7: unused |
| 1.3.6.1.4.1.5040.1.2.2.3.1.7.3 | NodewtWebioAn2PrtclHTTP | |||
| 1.3.6.1.4.1.5040.1.2.2.3.1.8 | NodewtWebioAn2Enable | |||
| 1.3.6.1.4.1.5040.1.2.2.3.1.8.1 | ScalarwtWebioAn2Enables | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Update enable Bit 1: Mail enable Bit 2: Snmp enable Bit 3: UDP… |
| 1.3.6.1.4.1.5040.1.2.2.3.1.9 | NodewtWebioAn2Startup | |||
| 1.3.6.1.4.1.5040.1.2.2.3.1.9.1 | ScalarwtWebioAn2StartupSite | read-write | mandatory | Binary coded start page: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1: Index.htm Bit 2: Home.htm Bit 3: User.htm Only one page may be selecte… |
| 1.3.6.1.4.1.5040.1.2.2.3.2 | NodewtWebioAn2Ports | |||
| 1.3.6.1.4.1.5040.1.2.2.3.2.1 | TablewtWebioAn2PortTable | not-accessible | mandatory | List of settings depending on the sensor number. |
| 1.3.6.1.4.1.5040.1.2.2.3.2.1.1 | RowwtWebioAn2PortEntry | not-accessible | mandatory | Sensor parameters for the individual sensor. |
| 1.3.6.1.4.1.5040.1.2.2.3.2.1.1.1 | ColumnwtWebioAn2PortName | read-write | mandatory | Name of the sensor. |
| 1.3.6.1.4.1.5040.1.2.2.3.2.1.1.2 | ColumnwtWebioAn2PortText | read-write | mandatory | Description of the sensor. |
| 1.3.6.1.4.1.5040.1.2.2.3.2.1.1.3 | ColumnwtWebioAn2PortOffset1 | read-write | mandatory | Offset calibration: Offset in degrees with maximum 2 decimal places at temperature 1. |
| 1.3.6.1.4.1.5040.1.2.2.3.2.1.1.4 | ColumnwtWebioAn2PortTemperature1 | read-write | mandatory | Offset calibration: Reference temperature 1 in degrees with maximum 2 decimal places. |
| 1.3.6.1.4.1.5040.1.2.2.3.2.1.1.5 | ColumnwtWebioAn2PortOffset2 | read-write | mandatory | Offset calibration: Offset in degrees with maximum 2 decimal places at temperature 2. |
| 1.3.6.1.4.1.5040.1.2.2.3.2.1.1.6 | ColumnwtWebioAn2PortTemperature2 | read-write | mandatory | Offset calibration: Reference temperature 1 in degrees with maximum 2 decimal places. |
| 1.3.6.1.4.1.5040.1.2.2.3.2.1.1.7 | ColumnwtWebioAn2PortComment | read-write | mandatory | Offset calibration: informations of date, name of operator, reference devices. |
| 1.3.6.1.4.1.5040.1.2.2.3.3 | NodewtWebioAn2Manufact | |||
| 1.3.6.1.4.1.5040.1.2.2.3.3.1 | ScalarwtWebioAn2MfName | read-write | mandatory | Manufacturer company name |
| 1.3.6.1.4.1.5040.1.2.2.3.3.2 | ScalarwtWebioAn2MfAddr | read-write | mandatory | Manufacturer address. |
| 1.3.6.1.4.1.5040.1.2.2.3.3.3 | ScalarwtWebioAn2MfHotline | read-write | mandatory | Manufacturer hotline. |
| 1.3.6.1.4.1.5040.1.2.2.3.3.4 | ScalarwtWebioAn2MfInternet | read-write | mandatory | Manufacturer Internet address. |
| 1.3.6.1.4.1.5040.1.2.2.3.3.5 | ScalarwtWebioAn2MfDeviceTyp | read-write | mandatory | Manufacturer device name (model number). |
| 1.3.6.1.4.1.5040.1.2.2.3.3.6 | ScalarwtWebioAn2MfOrderNo | read-write | mandatory | Manufacturer part number. |
| 1.3.6.1.4.1.5040.1.2.2.21 | NodewtWebioAn2Alert1 | This SNMP trap is generated when Alarm 1 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.2.22 | NodewtWebioAn2Alert2 | This SNMP trap is generated when Alarm 2 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.2.23 | NodewtWebioAn2Alert3 | This SNMP trap is generated when Alarm 3 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.2.24 | NodewtWebioAn2Alert4 | This SNMP trap is generated when Alarm 4 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.2.25 | NodewtWebioAn2Alert5 | This SNMP trap is generated when Alarm 5 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.2.26 | NodewtWebioAn2Alert6 | This SNMP trap is generated when Alarm 6 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.2.27 | NodewtWebioAn2Alert7 | This SNMP trap is generated when Alarm 7 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.2.28 | NodewtWebioAn2Alert8 | This SNMP trap is generated when Alarm 8 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.2.81 | NodewtWebioAn2Alert9 | This SNMP trap is generated when Alarm 1 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.2.82 | NodewtWebioAn2Alert10 | This SNMP trap is generated when Alarm 2 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.2.83 | NodewtWebioAn2Alert11 | This SNMP trap is generated when Alarm 3 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.2.84 | NodewtWebioAn2Alert12 | This SNMP trap is generated when Alarm 4 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.2.85 | NodewtWebioAn2Alert13 | This SNMP trap is generated when Alarm 5 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.2.86 | NodewtWebioAn2Alert14 | This SNMP trap is generated when Alarm 6 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.2.87 | NodewtWebioAn2Alert15 | This SNMP trap is generated when Alarm 7 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.2.88 | NodewtWebioAn2Alert16 | This SNMP trap is generated when Alarm 8 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.3 | NodewtWebioAn1 | |||
| 1.3.6.1.4.1.5040.1.2.3.1 | NodewtWebioAn1Temp | |||
| 1.3.6.1.4.1.5040.1.2.3.1.1 | ScalarwtWebioAn1Sensors | read-only | mandatory | Number of temperature sensors |
| 1.3.6.1.4.1.5040.1.2.3.1.2 | TablewtWebioAn1SensorTable | not-accessible | mandatory | List of sensors. |
| 1.3.6.1.4.1.5040.1.2.3.1.2.1 | RowwtWebioAn1SensorEntry | not-accessible | mandatory | Temperature sensor numbers. |
| 1.3.6.1.4.1.5040.1.2.3.1.2.1.1 | ColumnwtWebioAn1SensorNo | read-only | mandatory | Temperature sensor number. |
| 1.3.6.1.4.1.5040.1.2.3.1.3 | TablewtWebioAn1TempValueTable | not-accessible | mandatory | List of temperature values corresponding to the channel numbers. |
| 1.3.6.1.4.1.5040.1.2.3.1.3.1 | RowwtWebioAn1TempValueEntry | not-accessible | mandatory | Temperatures of the sensors. |
| 1.3.6.1.4.1.5040.1.2.3.1.3.1.1 | ColumnwtWebioAn1TempValue | read-only | mandatory | Temperature value of the sensor, ASCII, 5 characters in length. |
| 1.3.6.1.4.1.5040.1.2.3.1.4 | TablewtWebioAn1BinaryTempValueTable | not-accessible | mandatory | List of binary temperature values corresponding to the channel numbers. |
| 1.3.6.1.4.1.5040.1.2.3.1.4.1 | RowwtWebioAn1BinaryTempValueEntry | not-accessible | mandatory | Binary temperature values of the sensors. |
| 1.3.6.1.4.1.5040.1.2.3.1.4.1.1 | ColumnwtWebioAn1BinaryTempValue | read-only | mandatory | Binary temperature value of the sensor in 1/10 degrees Celsius, signed number, 0x7FFF indicates an invalid measured value. |
| 1.3.6.1.4.1.5040.1.2.3.2 | NodewtWebioAn1SessCntrl | |||
| 1.3.6.1.4.1.5040.1.2.3.2.1 | ScalarwtWebioAn1SessCntrlPassword | read-write | mandatory | Entering this password opens a session which is ended by writing a 1 to wtWebioAn1SessCntrlLogout. When read this variable provides a string of length zero. |
| 1.3.6.1.4.1.5040.1.2.3.2.2 | ScalarwtWebioAn1SessCntrlConfigMode | read-only | mandatory | When the device is in SNMP configuration mode, the value 1 is returned, otherwise 0. If the read value is 0 even though the password was written, the device is… |
| 1.3.6.1.4.1.5040.1.2.3.2.3 | ScalarwtWebioAn1SessCntrlLogout | read-write | mandatory | If the device is in configuration mode and the session was opened by this SNMP Manager, writing a 1 to this variable will end the session and all parameters ar… |
| 1.3.6.1.4.1.5040.1.2.3.2.4 | ScalarwtWebioAn1SessCntrlAdminPassword | read-write | mandatory | This password protects access to the variables with administrator rights. It can only be changed by the administrator. If no password was assigned, the valid p… |
| 1.3.6.1.4.1.5040.1.2.3.2.5 | ScalarwtWebioAn1SessCntrlConfigPassword | read-write | mandatory | This password protects access to the variables with configurator rights. It can be changed by the administrator and by the configurator. If no password was ass… |
| 1.3.6.1.4.1.5040.1.2.3.3 | NodewtWebioAn1Config | |||
| 1.3.6.1.4.1.5040.1.2.3.3.1 | NodewtWebioAn1Device | |||
| 1.3.6.1.4.1.5040.1.2.3.3.1.1 | NodewtWebioAn1Network | |||
| 1.3.6.1.4.1.5040.1.2.3.3.1.1.1 | ScalarwtWebioAn1IpAddress | read-write | mandatory | IP address of the Webio |
| 1.3.6.1.4.1.5040.1.2.3.3.1.1.2 | ScalarwtWebioAn1SubnetMask | read-write | mandatory | Subnet mask of the Webio |
| 1.3.6.1.4.1.5040.1.2.3.3.1.1.3 | ScalarwtWebioAn1Gateway | read-write | mandatory | Gateway of the Webio |
| 1.3.6.1.4.1.5040.1.2.3.3.1.1.4 | ScalarwtWebioAn1DnsServer1 | read-write | mandatory | IP address of the 1st DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.3.3.1.1.5 | ScalarwtWebioAn1DnsServer2 | read-write | mandatory | IP address of the 2nd DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.3.3.1.1.6 | ScalarwtWebioAn1AddConfig | read-write | mandatory | Additional configuration (1=ON): Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: BOOTP disable |
| 1.3.6.1.4.1.5040.1.2.3.3.1.2 | NodewtWebioAn1Text | |||
| 1.3.6.1.4.1.5040.1.2.3.3.1.2.1 | ScalarwtWebioAn1DeviceName | read-write | mandatory | Name of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.2.2 | ScalarwtWebioAn1DeviceText | read-write | mandatory | Description of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.2.3 | ScalarwtWebioAn1DeviceLocation | read-write | mandatory | Description of the location of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.2.4 | ScalarwtWebioAn1DeviceContact | read-write | mandatory | Contact address of the system operator of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.3 | NodewtWebioAn1TimeDate | |||
| 1.3.6.1.4.1.5040.1.2.3.3.1.3.1 | NodewtWebioAn1TimeZone | |||
| 1.3.6.1.4.1.5040.1.2.3.3.1.3.1.1 | ScalarwtWebioAn1TzName | read-write | mandatory | Name of the time zone (winter time). |
| 1.3.6.1.4.1.5040.1.2.3.3.1.3.1.2 | ScalarwtWebioAn1TzOffsetHrs | read-write | mandatory | Offset hours for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.3.1.3 | ScalarwtWebioAn1TzOffsetMin | read-write | mandatory | Offset minutes for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.3.1.4 | ScalarwtWebioAn1StTzName | read-write | mandatory | Name of the time zone (summer time). |
| 1.3.6.1.4.1.5040.1.2.3.3.1.3.1.5 | ScalarwtWebioAn1StTzOffsetHrs | read-write | mandatory | Offset hours of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.3.1.6 | ScalarwtWebioAn1StTzOffsetMin | read-write | mandatory | Offset minutes of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.3.1.7 | ScalarwtWebioAn1StTzStartMonth | read-write | mandatory | Month in which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.3.1.8 | ScalarwtWebioAn1StTzStartMode | read-write | mandatory | Mode of the day of the week for which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.3.1.9 | ScalarwtWebioAn1StTzStartWday | read-write | mandatory | Day of the week on which the change is made from winter time to summer time |
| 1.3.6.1.4.1.5040.1.2.3.3.1.3.1.10 | ScalarwtWebioAn1StTzStartHrs | read-write | mandatory | Hour in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.3.1.11 | ScalarwtWebioAn1StTzStartMin | read-write | mandatory | Minute in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.3.1.12 | ScalarwtWebioAn1StTzStopMonth | read-write | mandatory | Month in which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.3.1.13 | ScalarwtWebioAn1StTzStopMode | read-write | mandatory | Mode of the week day on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.3.1.14 | ScalarwtWebioAn1StTzStopWday | read-write | mandatory | Day of the week on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.3.1.15 | ScalarwtWebioAn1StTzStopHrs | read-write | mandatory | Hour at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.3.1.16 | ScalarwtWebioAn1StTzStopMin | read-write | mandatory | Minute at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.3.2 | NodewtWebioAn1TimeServer | |||
| 1.3.6.1.4.1.5040.1.2.3.3.1.3.2.1 | ScalarwtWebioAn1TimeServer1 | read-write | mandatory | IP address or name of the 1st time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.3.3.1.3.2.2 | ScalarwtWebioAn1TimeServer2 | read-write | mandatory | IP address or name of the 2nd time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.3.3.1.3.3 | NodewtWebioAn1DeviceClock | |||
| 1.3.6.1.4.1.5040.1.2.3.3.1.3.3.1 | ScalarwtWebioAn1ClockHrs | read-write | mandatory | Clock hours taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.3.3.2 | ScalarwtWebioAn1ClockMin | read-write | mandatory | Clock minutes taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.3.3.3 | ScalarwtWebioAn1ClockDay | read-write | mandatory | Date: Day of the month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.3.3.4 | ScalarwtWebioAn1ClockMonth | read-write | mandatory | Date: Month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.3.3.5 | ScalarwtWebioAn1ClockYear | read-write | mandatory | Date: Year, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.4 | NodewtWebioAn1MailAdmin | |||
| 1.3.6.1.4.1.5040.1.2.3.3.1.4.1 | ScalarwtWebioAn1MailAdName | read-write | mandatory | Device name for mail administration. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.4.2 | ScalarwtWebioAn1MailReply | read-write | mandatory | Reply address for the mail server. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.4.3 | ScalarwtWebioAn1MailServer | read-write | mandatory | Name or IP address of the mail server. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.5 | NodewtWebioAn1Alarm | |||
| 1.3.6.1.4.1.5040.1.2.3.3.1.5.1 | ScalarwtWebioAn1AlarmCount | read-only | mandatory | Number of independent alarms. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.5.2 | TablewtWebioAn1AlarmIfTable | not-accessible | mandatory | List of alarm indices. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.5.2.1 | RowwtWebioAn1AlarmIfEntry | not-accessible | mandatory | Numbers of the alarms. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.5.2.1.1 | ColumnwtWebioAn1AlarmNo | read-only | mandatory | Alarm number. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.5.3 | TablewtWebioAn1AlarmTable | not-accessible | mandatory | List of settings depending on the alarm number. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.5.3.1 | RowwtWebioAn1AlarmEntry | not-accessible | mandatory | Alarm parameters of the individual alarms. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.5.3.1.1 | ColumnwtWebioAn1AlarmTrigger | read-write | mandatory | Binary coded trigger condition: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Sensor 1 Bit 1: Timer Bit 2: ColdStart Bit 3: WarmStart |
| 1.3.6.1.4.1.5040.1.2.3.3.1.5.3.1.2 | ColumnwtWebioAn1AlarmMin | read-write | mandatory | Minimum temperature in degrees with maximum 2 decimal places. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.5.3.1.3 | ColumnwtWebioAn1AlarmMax | read-write | mandatory | Maximum temperature in degrees with maximum 2 decimal places. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.5.3.1.4 | ColumnwtWebioAn1AlarmInterval | read-write | mandatory | Send interval for alarm messages. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.5.3.1.5 | ColumnwtWebioAn1AlarmEnable | read-write | mandatory | Binary coded alarm enable: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Mail Enable Bit 1: SNMP Trap enable Bit 2: TCP Client enable |
| 1.3.6.1.4.1.5040.1.2.3.3.1.5.3.1.6 | ColumnwtWebioAn1AlarmEMailAddr | read-write | mandatory | E-Mail address for sending the alarm mail to. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.5.3.1.7 | ColumnwtWebioAn1AlarmMailSubject | read-write | mandatory | Subject line for alarm mail. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.5.3.1.8 | ColumnwtWebioAn1AlarmMailText | read-write | mandatory | Alarm mail text: <T1> provides the current temperature. <Z> provides the current time. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.5.3.1.9 | ColumnwtWebioAn1AlarmManagerIP | read-write | mandatory | Name or IP address of the SNMP Manager which accepts the trap. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.5.3.1.10 | ColumnwtWebioAn1AlarmTrapText | read-write | mandatory | This text is sent in the trap body. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.5.3.1.11 | ColumnwtWebioAn1AlarmMailOptions | read-write | mandatory | Binary coded options: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0 : Attach Thermo.csv Enable Bit 1-7: unused |
| 1.3.6.1.4.1.5040.1.2.3.3.1.5.3.1.12 | ColumnwtWebioAn1AlarmTcpIpAddr | read-write | mandatory | Name or IP address of the TCP server which accepts the trap. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.5.3.1.13 | ColumnwtWebioAn1AlarmTcpPort | read-write | mandatory | Port number of the TCP server which accepts the trap. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.5.3.1.14 | ColumnwtWebioAn1AlarmTcpText | read-write | mandatory | This text is sent in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.5.3.1.15 | ColumnwtWebioAn1AlarmHysteresis | read-write | mandatory | Temperature changes of this size clears the alarm state (MAX-hyst, MIN+hyst.) , in degrees with maximum 2 decimal places. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.5.3.1.16 | ColumnwtWebioAn1AlarmClearMailSubject | read-write | mandatory | Subject line for alarm clear mail. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.5.3.1.17 | ColumnwtWebioAn1AlarmClearMailText | read-write | mandatory | Alarm clear mail text: <Tn> provides the current temperature; n = 1..8. <Z> provides the current time. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.5.3.1.18 | ColumnwtWebioAn1AlarmClearTrapText | read-write | mandatory | This text is sent in the trap body. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.5.3.1.19 | ColumnwtWebioAn1AlarmClearTcpText | read-write | mandatory | This text is sent in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.6 | NodewtWebioAn1Datalogger | |||
| 1.3.6.1.4.1.5040.1.2.3.3.1.6.1 | ScalarwtWebioAn1LoggerTimebase | read-write | mandatory | Time base of the data logger |
| 1.3.6.1.4.1.5040.1.2.3.3.1.6.2 | ScalarwtWebioAn1LoggerSensorSel | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Sensor 1 |
| 1.3.6.1.4.1.5040.1.2.3.3.1.7 | NodewtWebioAn1Protocol | |||
| 1.3.6.1.4.1.5040.1.2.3.3.1.7.1 | NodewtWebioAn1PrtclUDP | |||
| 1.3.6.1.4.1.5040.1.2.3.3.1.7.1.1 | ScalarwtWebioAn1PrtclUdpPort | read-write | mandatory | Udp port to which the Udp queries GET Single can be sent |
| 1.3.6.1.4.1.5040.1.2.3.3.1.7.2 | NodewtWebioAn1PrtclSNMP | |||
| 1.3.6.1.4.1.5040.1.2.3.3.1.7.2.1 | ScalarwtWebioAn1PrtclSnmpCommunityStringRead | read-write | mandatory | Community string read only |
| 1.3.6.1.4.1.5040.1.2.3.3.1.7.2.2 | ScalarwtWebioAn1PrtclSnmpCommunityStringReadWrite | read-write | mandatory | Community string read / write |
| 1.3.6.1.4.1.5040.1.2.3.3.1.7.2.3 | ScalarwtWebioAn1SystemTrapManagerIP | read-write | mandatory | Name or IP address of the TCP server which accepts the system trap. |
| 1.3.6.1.4.1.5040.1.2.3.3.1.7.2.4 | ScalarwtWebioAn1SystemTrapEnable | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2-7: unused |
| 1.3.6.1.4.1.5040.1.2.3.3.1.7.3 | NodewtWebioAn1PrtclHTTP | |||
| 1.3.6.1.4.1.5040.1.2.3.3.1.8 | NodewtWebioAn1Enable | |||
| 1.3.6.1.4.1.5040.1.2.3.3.1.8.1 | ScalarwtWebioAn1Enables | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Update enable Bit 1: Mail enable Bit 2: Snmp enable Bit 3: UDP… |
| 1.3.6.1.4.1.5040.1.2.3.3.1.9 | NodewtWebioAn1Startup | |||
| 1.3.6.1.4.1.5040.1.2.3.3.1.9.1 | ScalarwtWebioAn1StartupSite | read-write | mandatory | Binary coded start page: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1: Index.htm Bit 2: Home.htm Bit 3: User.htm Only one page may be selecte… |
| 1.3.6.1.4.1.5040.1.2.3.3.2 | NodewtWebioAn1Ports | |||
| 1.3.6.1.4.1.5040.1.2.3.3.2.1 | TablewtWebioAn1PortTable | not-accessible | mandatory | List of settings depending on the sensor number. |
| 1.3.6.1.4.1.5040.1.2.3.3.2.1.1 | RowwtWebioAn1PortEntry | not-accessible | mandatory | Sensor parameters for the individual sensors. |
| 1.3.6.1.4.1.5040.1.2.3.3.2.1.1.1 | ColumnwtWebioAn1PortName | read-write | mandatory | Name of the sensor. |
| 1.3.6.1.4.1.5040.1.2.3.3.2.1.1.2 | ColumnwtWebioAn1PortText | read-write | mandatory | Description of the sensor. |
| 1.3.6.1.4.1.5040.1.2.3.3.2.1.1.3 | ColumnwtWebioAn1PortOffset1 | read-write | mandatory | Offset calibration: Offset in degrees with maximum 2 decimal places at temperature 1. |
| 1.3.6.1.4.1.5040.1.2.3.3.2.1.1.4 | ColumnwtWebioAn1PortTemperature1 | read-write | mandatory | Offset calibration: Reference temperature 1 in degrees with maximum 2 decimal places. |
| 1.3.6.1.4.1.5040.1.2.3.3.2.1.1.5 | ColumnwtWebioAn1PortOffset2 | read-write | mandatory | Offset calibration: Offset in degrees with maximum 2 decimal places at temperature 2. |
| 1.3.6.1.4.1.5040.1.2.3.3.2.1.1.6 | ColumnwtWebioAn1PortTemperature2 | read-write | mandatory | Offset calibration: Reference temperature 1 in degrees with maximum 2 decimal places. |
| 1.3.6.1.4.1.5040.1.2.3.3.2.1.1.7 | ColumnwtWebioAn1PortComment | read-write | mandatory | Offset calibration: informations of date, name of operator, reference devices. |
| 1.3.6.1.4.1.5040.1.2.3.3.3 | NodewtWebioAn1Manufact | |||
| 1.3.6.1.4.1.5040.1.2.3.3.3.1 | ScalarwtWebioAn1MfName | read-write | mandatory | Manufacturer company name |
| 1.3.6.1.4.1.5040.1.2.3.3.3.2 | ScalarwtWebioAn1MfAddr | read-write | mandatory | Manufacturer address. |
| 1.3.6.1.4.1.5040.1.2.3.3.3.3 | ScalarwtWebioAn1MfHotline | read-write | mandatory | Manufacturer hotline. |
| 1.3.6.1.4.1.5040.1.2.3.3.3.4 | ScalarwtWebioAn1MfInternet | read-write | mandatory | Manufacturer Internet address. |
| 1.3.6.1.4.1.5040.1.2.3.3.3.5 | ScalarwtWebioAn1MfDeviceTyp | read-write | mandatory | Manufacturer device name (model number). |
| 1.3.6.1.4.1.5040.1.2.3.3.3.6 | ScalarwtWebioAn1MfOrderNo | read-write | mandatory | Manufacturer part number. |
| 1.3.6.1.4.1.5040.1.2.3.31 | NodewtWebioAn1Alert1 | This SNMP trap is generated when Alarm 1 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.3.32 | NodewtWebioAn1Alert2 | This SNMP trap is generated when Alarm 2 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.3.33 | NodewtWebioAn1Alert3 | This SNMP trap is generated when Alarm 3 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.3.34 | NodewtWebioAn1Alert4 | This SNMP trap is generated when Alarm 4 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.3.35 | NodewtWebioAn1Alert5 | This SNMP trap is generated when Alarm 5 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.3.36 | NodewtWebioAn1Alert6 | This SNMP trap is generated when Alarm 6 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.3.37 | NodewtWebioAn1Alert7 | This SNMP trap is generated when Alarm 7 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.3.38 | NodewtWebioAn1Alert8 | This SNMP trap is generated when Alarm 8 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.3.91 | NodewtWebioAn1Alert9 | This SNMP trap is generated when Alarm 1 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.3.92 | NodewtWebioAn1Alert10 | This SNMP trap is generated when Alarm 2 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.3.93 | NodewtWebioAn1Alert11 | This SNMP trap is generated when Alarm 3 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.3.94 | NodewtWebioAn1Alert12 | This SNMP trap is generated when Alarm 4 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.3.95 | NodewtWebioAn1Alert13 | This SNMP trap is generated when Alarm 5 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.3.96 | NodewtWebioAn1Alert14 | This SNMP trap is generated when Alarm 6 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.3.97 | NodewtWebioAn1Alert15 | This SNMP trap is generated when Alarm 7 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.3.98 | NodewtWebioAn1Alert16 | This SNMP trap is generated when Alarm 8 was cleared, SNMP trap enable is set and SNMP is enabled. |