Webio-Digital-MIB-US
4346 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC-1212 | OBJECT-TYPE |
| RFC-1215 | TRAP-TYPE |
| RFC1155-SMI | enterprises IpAddress NetworkAddress TimeTicks |
| RFC1213-MIB | DisplayString PhysAddress |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.5040 | Nodewut | |||
| 1.3.6.1.4.1.5040.1 | NodewtComServer | |||
| 1.3.6.1.4.1.5040.1.2 | NodewtWebio | |||
| 1.3.6.1.4.1.5040.1.2.4 | NodewtWebioEA12x12 | |||
| 1.3.6.1.4.1.5040.1.2.4.1 | NodewtWebioEA12x12InOut | |||
| 1.3.6.1.4.1.5040.1.2.4.1.1 | ScalarwtWebioEA12x12Inputs | read-only | mandatory | Number of idependent inputs. |
| 1.3.6.1.4.1.5040.1.2.4.1.2 | ScalarwtWebioEA12x12Outputs | read-only | mandatory | Number of idependent outputs. |
| 1.3.6.1.4.1.5040.1.2.4.1.3 | TablewtWebioEA12x12InputTable | not-accessible | mandatory | List of input indices. |
| 1.3.6.1.4.1.5040.1.2.4.1.3.1 | RowwtWebioEA12x12InputEntry | not-accessible | mandatory | Number of the inputs. |
| 1.3.6.1.4.1.5040.1.2.4.1.3.1.1 | ColumnwtWebioEA12x12InputNo | read-only | mandatory | Index numbers of the inputs. |
| 1.3.6.1.4.1.5040.1.2.4.1.3.1.2 | ColumnwtWebioEA12x12InputCounter | read-only | mandatory | Value of the input counter. |
| 1.3.6.1.4.1.5040.1.2.4.1.3.1.3 | ColumnwtWebioEA12x12InputCounterClear | read-only | mandatory | Clears the input counter after returning its value. |
| 1.3.6.1.4.1.5040.1.2.4.1.3.1.4 | ColumnwtWebioEA12x12InputState | read-only | mandatory | Value of a single input bit, 0-OFF, 1-ON. |
| 1.3.6.1.4.1.5040.1.2.4.1.4 | ScalarwtWebioEA12x12InputValue | read-only | mandatory | This variable is used to read the inputs of the digital I/O port. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corres… |
| 1.3.6.1.4.1.5040.1.2.4.1.5 | TablewtWebioEA12x12OutputTable | not-accessible | mandatory | List of output indices. |
| 1.3.6.1.4.1.5040.1.2.4.1.5.1 | RowwtWebioEA12x12OutputEntry | not-accessible | mandatory | Number of the outputs. |
| 1.3.6.1.4.1.5040.1.2.4.1.5.1.1 | ColumnwtWebioEA12x12OutputNo | read-only | mandatory | Output number. |
| 1.3.6.1.4.1.5040.1.2.4.1.5.1.2 | ColumnwtWebioEA12x12OutputState | read-write | mandatory | Value of a single output bit, 0-OFF, 1-ON. |
| 1.3.6.1.4.1.5040.1.2.4.1.6 | ScalarwtWebioEA12x12OutputValue | read-write | mandatory | This variable is used to read and write the outputs of the digital I/O port. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. B… |
| 1.3.6.1.4.1.5040.1.2.4.1.7 | ScalarwtWebioEA12x12SetOutput | read-write | mandatory | This variable allows setting of individual digital outputs. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds … |
| 1.3.6.1.4.1.5040.1.2.4.2 | NodewtWebioEA12x12SessCntrl | |||
| 1.3.6.1.4.1.5040.1.2.4.2.1 | ScalarwtWebioEA12x12SessCntrlPassword | read-write | mandatory | Entering this password opens a session which is ended by writing a 1 to wtWebioEA12x12SessCntrlLogout. When read this variable provides a string of length zero. |
| 1.3.6.1.4.1.5040.1.2.4.2.2 | ScalarwtWebioEA12x12SessCntrlConfigMode | read-only | mandatory | When the device is in SNMP configuration mode, the value 1 is returned, otherwise 0. If the read value is 0 even though the password was written, the device is… |
| 1.3.6.1.4.1.5040.1.2.4.2.3 | ScalarwtWebioEA12x12SessCntrlLogout | read-write | mandatory | If the device is in configuration mode and the session was opened by this SNMP Manager, writing a 1 to this variable will end the session and all parameters ar… |
| 1.3.6.1.4.1.5040.1.2.4.2.4 | ScalarwtWebioEA12x12SessCntrlAdminPassword | read-write | mandatory | This password protects access to the variables with administrator rights. It can only be changed by the administrator. If no password was assigned, the valid p… |
| 1.3.6.1.4.1.5040.1.2.4.2.5 | ScalarwtWebioEA12x12SessCntrlConfigPassword | read-write | mandatory | This password protects access to the variables with configurator rights. It can be changed by the administrator and by the configurator. If no password was ass… |
| 1.3.6.1.4.1.5040.1.2.4.3 | NodewtWebioEA12x12Config | |||
| 1.3.6.1.4.1.5040.1.2.4.3.1 | NodewtWebioEA12x12Device | |||
| 1.3.6.1.4.1.5040.1.2.4.3.1.1 | NodewtWebioEA12x12Text | |||
| 1.3.6.1.4.1.5040.1.2.4.3.1.1.1 | ScalarwtWebioEA12x12DeviceName | read-write | mandatory | Name of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.1.2 | ScalarwtWebioEA12x12DeviceText | read-write | mandatory | Description of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.1.3 | ScalarwtWebioEA12x12DeviceLocation | read-write | mandatory | Description of the location of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.1.4 | ScalarwtWebioEA12x12DeviceContact | read-write | mandatory | Contact address of the system operator of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.2 | NodewtWebioEA12x12TimeDate | |||
| 1.3.6.1.4.1.5040.1.2.4.3.1.2.1 | NodewtWebioEA12x12TimeZone | |||
| 1.3.6.1.4.1.5040.1.2.4.3.1.2.1.1 | ScalarwtWebioEA12x12TzOffsetHrs | read-write | mandatory | Offset hours for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.2.1.2 | ScalarwtWebioEA12x12TzOffsetMin | read-write | mandatory | Offset minutes for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.2.1.3 | ScalarwtWebioEA12x12TzEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Timezone |
| 1.3.6.1.4.1.5040.1.2.4.3.1.2.1.4 | ScalarwtWebioEA12x12StTzOffsetHrs | read-write | mandatory | Offset hours of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.2.1.5 | ScalarwtWebioEA12x12StTzOffsetMin | read-write | mandatory | Offset minutes of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.2.1.6 | ScalarwtWebioEA12x12StTzEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Summertime |
| 1.3.6.1.4.1.5040.1.2.4.3.1.2.1.7 | ScalarwtWebioEA12x12StTzStartMonth | read-write | mandatory | Month in which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.2.1.8 | ScalarwtWebioEA12x12StTzStartMode | read-write | mandatory | Mode of the day of the week for which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.2.1.9 | ScalarwtWebioEA12x12StTzStartWday | read-write | mandatory | Day of the week on which the change is made from winter time to summer time |
| 1.3.6.1.4.1.5040.1.2.4.3.1.2.1.10 | ScalarwtWebioEA12x12StTzStartHrs | read-write | mandatory | Hour in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.2.1.11 | ScalarwtWebioEA12x12StTzStartMin | read-write | mandatory | Minute in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.2.1.12 | ScalarwtWebioEA12x12StTzStopMonth | read-write | mandatory | Month in which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.2.1.13 | ScalarwtWebioEA12x12StTzStopMode | read-write | mandatory | Mode of the week day on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.2.1.14 | ScalarwtWebioEA12x12StTzStopWday | read-write | mandatory | Day of the week on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.2.1.15 | ScalarwtWebioEA12x12StTzStopHrs | read-write | mandatory | Hour at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.2.1.16 | ScalarwtWebioEA12x12StTzStopMin | read-write | mandatory | Minute at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.2.2 | NodewtWebioEA12x12TimeServer | |||
| 1.3.6.1.4.1.5040.1.2.4.3.1.2.2.1 | ScalarwtWebioEA12x12TimeServer1 | read-write | mandatory | IP address or name of the 1st time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.4.3.1.2.2.2 | ScalarwtWebioEA12x12TimeServer2 | read-write | mandatory | IP address or name of the 2nd time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.4.3.1.2.2.3 | ScalarwtWebioEA12x12TsEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Time Server |
| 1.3.6.1.4.1.5040.1.2.4.3.1.2.2.4 | ScalarwtWebioEA12x12TsSyncTime | read-write | mandatory | Daily synchronisation time with the time server (hour: 0-23). |
| 1.3.6.1.4.1.5040.1.2.4.3.1.2.3 | NodewtWebioEA12x12DeviceClock | |||
| 1.3.6.1.4.1.5040.1.2.4.3.1.2.3.1 | ScalarwtWebioEA12x12ClockHrs | read-write | mandatory | Clock hours taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.2.3.2 | ScalarwtWebioEA12x12ClockMin | read-write | mandatory | Clock minutes taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.2.3.3 | ScalarwtWebioEA12x12ClockDay | read-write | mandatory | Date: Day of the month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.2.3.4 | ScalarwtWebioEA12x12ClockMonth | read-write | mandatory | Date: Month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.2.3.5 | ScalarwtWebioEA12x12ClockYear | read-write | mandatory | Date: Year, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3 | NodewtWebioEA12x12Basic | |||
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.1 | NodewtWebioEA12x12Network | |||
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.1.1 | ScalarwtWebioEA12x12IpAddress | read-write | mandatory | IP address of the Webio |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.1.2 | ScalarwtWebioEA12x12SubnetMask | read-write | mandatory | Subnet mask of the Webio |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.1.3 | ScalarwtWebioEA12x12Gateway | read-write | mandatory | Gateway of the Webio |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.1.4 | ScalarwtWebioEA12x12DnsServer1 | read-write | mandatory | IP address of the 1st DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.1.5 | ScalarwtWebioEA12x12DnsServer2 | read-write | mandatory | IP address of the 2nd DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.1.6 | ScalarwtWebioEA12x12AddConfig | read-write | mandatory | Additional configuration (1=ON): Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1: DHCP enable Bit 0: BOOTP enable |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.2 | NodewtWebioEA12x12HTTP | |||
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.2.1 | ScalarwtWebioEA12x12Startup | read-write | mandatory | Binary coded start page, more than one page must not be selected: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 2: user.htm Bit 1: home.htm Bit … |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.2.2 | ScalarwtWebioEA12x12GetHeaderEnable | read-write | mandatory | If bits are set, every answer of a short form GET question will be lead by the IP-address and name of the device (Header) or a HTTP header (HTTP): Octet 1: unu… |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.2.3 | ScalarwtWebioEA12x12HttpInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.2.4 | ScalarwtWebioEA12x12HttpPort | read-write | mandatory | Definition of the standard HTML port (Default: 80). |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.3 | NodewtWebioEA12x12Mail | |||
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.3.1 | ScalarwtWebioEA12x12MailAdName | read-write | mandatory | Device name for mail administration. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.3.2 | ScalarwtWebioEA12x12MailReply | read-write | mandatory | Reply address for the mail server. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.3.3 | ScalarwtWebioEA12x12MailServer | read-write | mandatory | Name or IP address of the mail server. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.3.4 | ScalarwtWebioEA12x12MailEnable | read-write | mandatory | Set this bit to enable the sending of mails: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Mail enable |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.3.5 | ScalarwtWebioEA12x12MailAuthentication | read-write | mandatory | Selection of the authentication modi: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTE… |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.3.6 | ScalarwtWebioEA12x12MailAuthUser | read-write | mandatory | Name of the user to be authenticated. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.3.7 | ScalarwtWebioEA12x12MailAuthPassword | read-write | mandatory | Authentication password. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.3.8 | ScalarwtWebioEA12x12MailPop3Server | read-write | mandatory | Name or Ip-address of the POP3 Servers. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.4 | NodewtWebioEA12x12SNMP | |||
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.4.1 | ScalarwtWebioEA12x12SnmpEnable | read-write | mandatory | Set bit 0 to enable SNMP. If disabled, the device did not respond to any SNMP requests. Bit 1 decided wether the community string of read operations is compare… |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.4.2 | ScalarwtWebioEA12x12SnmpCommunityStringRead | read-write | mandatory | Community string read only |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.4.3 | ScalarwtWebioEA12x12SnmpCommunityStringReadWrite | read-write | mandatory | Community string read / write |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.4.4 | ScalarwtWebioEA12x12SnmpSystemTrapManagerIP | read-write | mandatory | Name or IP address of the TCP server which accepts the system trap. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.4.5 | ScalarwtWebioEA12x12SnmpSystemTrapEnable | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2: Diag messages Bit 3-7: unused |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.5 | NodewtWebioEA12x12UDP | |||
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.5.1 | ScalarwtWebioEA12x12UdpAdminPort | read-write | mandatory | Udp port to which the Udp queries ( short form GET requests) can be sent. This port number must be unique within the device. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.5.2 | ScalarwtWebioEA12x12UdpEnable | read-write | mandatory | Set this bit to enable UDP support: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : UDP enable |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.5.3 | ScalarwtWebioEA12x12UdpRemotePort | read-write | mandatory | Udp remote port setting. If this value is set to zero, the source port read from a request will be used as destination port for the answer. A non zero value fo… |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.6 | NodewtWebioEA12x12Binary | |||
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.6.1 | ScalarwtWebioEA12x12BinaryModeCount | read-only | mandatory | Number of independent binary channels. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.6.2 | TablewtWebioEA12x12BinaryIfTable | not-accessible | mandatory | Table of indices. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.6.2.1 | RowwtWebioEA12x12BinaryIfEntry | not-accessible | mandatory | Indices of the binary channels. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.6.2.1.1 | ColumnwtWebioEA12x12BinaryModeNo | read-only | mandatory | Number of the binary channel. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.6.3 | TablewtWebioEA12x12BinaryTable | not-accessible | mandatory | Table of properties of the binary mode. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.6.3.1 | RowwtWebioEA12x12BinaryEntry | not-accessible | mandatory | Binary properties. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.6.3.1.1 | ColumnwtWebioEA12x12BinaryOperationMode | read-write | mandatory | Selection of the operation mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: … |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.6.3.1.2 | ColumnwtWebioEA12x12BinaryTcpServerLocalPort | read-write | mandatory | Local TCP port for data exchange in this server mode. This port number must be unique within the device. Reserved port number must not be used (refere to the m… |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.6.3.1.3 | ColumnwtWebioEA12x12BinaryTcpServerInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.6.3.1.4 | ColumnwtWebioEA12x12BinaryTcpServerApplicationMode | read-write | mandatory | Selection of the application mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4… |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.6.3.1.5 | ColumnwtWebioEA12x12BinaryTcpClientLocalPort | read-write | mandatory | Local TCP port for data exchange in this client mode. This port number must be unique within the device. Reserved port number must not be used (refere to the m… |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.6.3.1.6 | ColumnwtWebioEA12x12BinaryTcpClientServerPort | read-write | mandatory | Port number of the server. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when setting t… |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.6.3.1.7 | ColumnwtWebioEA12x12BinaryTcpClientServerIpAddr | read-write | mandatory | Ip address of the server. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when setting th… |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.6.3.1.8 | ColumnwtWebioEA12x12BinaryTcpClientServerPassword | read-write | mandatory | Building a connection may be protected by the administrator password of the server. Enter the server password to establish the connection, if a server administ… |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.6.3.1.9 | ColumnwtWebioEA12x12BinaryTcpClientInactivity | read-write | mandatory | Connection timeout in 100ms. If no data are exchanged within the specified time, the device closes the connection to the server. The value 0 deactivates the ti… |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.6.3.1.10 | ColumnwtWebioEA12x12BinaryTcpClientInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.6.3.1.11 | ColumnwtWebioEA12x12BinaryTcpClientInterval | read-write | mandatory | Configurable interval with a 100ms base, in which the Webio device sends data to the configured application. A interval of zero stopps the periodical sending. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.6.3.1.12 | ColumnwtWebioEA12x12BinaryTcpClientApplicationMode | read-write | mandatory | Selection of the application mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4… |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.6.3.1.13 | ColumnwtWebioEA12x12BinaryUdpPeerLocalPort | read-write | mandatory | Local UDP port for data exchange in this peer to peer mode. This port number must be unique within the device. Reserved port number must not be used (refere to… |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.6.3.1.14 | ColumnwtWebioEA12x12BinaryUdpPeerRemotePort | read-write | mandatory | Port number of the remote device. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when se… |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.6.3.1.15 | ColumnwtWebioEA12x12BinaryUdpPeerRemoteIpAddr | read-write | mandatory | Ip address of the remote device. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when set… |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.6.3.1.16 | ColumnwtWebioEA12x12BinaryUdpPeerInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.6.3.1.17 | ColumnwtWebioEA12x12BinaryUdpPeerInterval | read-write | mandatory | Configurable interval with a 100ms base, in which the Webio device sends data to the configured remote device. A interval of zero stopps the periodical sending. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.6.3.1.18 | ColumnwtWebioEA12x12BinaryUdpPeerApplicationMode | read-write | mandatory | Selection of the application mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4… |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.6.3.1.19 | ColumnwtWebioEA12x12BinaryConnectedPort | read-only | mandatory | Port number of the remote device, after connection has been established. In case of no connection or missing port informations a zero will be read. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.6.3.1.20 | ColumnwtWebioEA12x12BinaryConnectedIpAddr | read-only | mandatory | IP address of the remote device, after connection has been established. In case of no connection or missing port informations 0.0.0.0 will be read. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.6.3.1.21 | ColumnwtWebioEA12x12BinaryTcpServerClientHttpPort | read-write | mandatory | HTTP port number of the remote device at TCP Server Mode. If an mailfunction occurs status informations will be send to this port. Not used at mode Compatible … |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.6.3.1.22 | ColumnwtWebioEA12x12BinaryTcpClientServerHttpPort | read-write | mandatory | HTTP port number of the remote device at TCP Client Mode. In the operating mode Box2Box connection status informations will be exchanged through this port. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.7 | NodewtWebioEA12x12Syslog | |||
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.7.1 | ScalarwtWebioEA12x12SyslogServerIP | read-write | mandatory | Name or IP address of the Syslog server, which accepts the Syslog messgaes. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.7.2 | ScalarwtWebioEA12x12SyslogServerPort | read-write | mandatory | Portnumber of the Syslog servers, default 514. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.7.3 | ScalarwtWebioEA12x12SyslogSystemMessagesEnable | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2: Diag Messages Bit 3-7: unused |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.7.4 | ScalarwtWebioEA12x12SyslogEnable | read-write | mandatory | Set bit 0to enable Syslog: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Syslog enable |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.8 | NodewtWebioEA12x12FTP | |||
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.8.1 | ScalarwtWebioEA12x12FTPServerIP | read-write | mandatory | Name or IP address of the FTP server, which accepts the FTP messages. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.8.2 | ScalarwtWebioEA12x12FTPServerControlPort | read-write | mandatory | Portnumber of the control port of the FTP server, default 21. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.8.3 | ScalarwtWebioEA12x12FTPUserName | read-write | mandatory | FTP Loggin: user name. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.8.4 | ScalarwtWebioEA12x12FTPPassword | read-write | mandatory | FTP Loggin: user password. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.8.5 | ScalarwtWebioEA12x12FTPAccount | read-write | mandatory | FTP Loggin: name of account. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.8.6 | ScalarwtWebioEA12x12FTPOption | read-write | mandatory | Bit 0 switches the FTP Server in Passiv-Mode, the Client controls the data connection on its own: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit … |
| 1.3.6.1.4.1.5040.1.2.4.3.1.3.8.7 | ScalarwtWebioEA12x12FTPEnable | read-write | mandatory | Set Bit 0 to enable FTP: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : FTP enable |
| 1.3.6.1.4.1.5040.1.2.4.3.1.4 | NodewtWebioEA12x12OutputMode | |||
| 1.3.6.1.4.1.5040.1.2.4.3.1.4.1 | TablewtWebioEA12x12OutputModeTable | not-accessible | mandatory | Table of output mode configurations dependent on the output indices. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.4.1.1 | RowwtWebioEA12x12OutputModeEntry | not-accessible | mandatory | Output mode configurations of the individual outputs. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.4.1.1.1 | ColumnwtWebioEA12x12OutputModeBit | read-write | mandatory | This binary coded output mode defines the individual operation mode for any output. More than one mode must not be selected. The OCTETS are interpreted bit-by-… |
| 1.3.6.1.4.1.5040.1.2.4.3.1.4.2 | ScalarwtWebioEA12x12SafetyTimeout | read-write | mandatory | After this period of time (multiple of 100ms) without receiving data outputs switch to their Safety States. For each output a independend safety state could be… |
| 1.3.6.1.4.1.5040.1.2.4.3.1.4.3 | ScalarwtWebioEA12x12LoadControlEnable | read-write | mandatory | Here the function of automatic load control can be enabled. All output were tested in pairs (0-1, 2-3, 4-5, 6-7, 8-9, 10-11). If an error occours at one output… |
| 1.3.6.1.4.1.5040.1.2.4.3.1.5 | NodewtWebioEA12x12Alarm | |||
| 1.3.6.1.4.1.5040.1.2.4.3.1.5.1 | ScalarwtWebioEA12x12AlarmCount | read-only | mandatory | Number of independent alarms. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.5.2 | TablewtWebioEA12x12AlarmIfTable | not-accessible | mandatory | List of alarm indices. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.5.2.1 | RowwtWebioEA12x12AlarmIfEntry | not-accessible | mandatory | Numbers of the alarms. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.5.2.1.1 | ColumnwtWebioEA12x12AlarmNo | read-only | mandatory | Numbers of the alarms. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.5.3 | TablewtWebioEA12x12AlarmTable | not-accessible | mandatory | List of settings depending on the alarm number. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.5.3.1 | RowwtWebioEA12x12AlarmEntry | not-accessible | mandatory | Alarm parameters of the individual alarms. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.5.3.1.1 | ColumnwtWebioEA12x12AlarmInputTrigger | read-write | mandatory | This variable allows setting of individual input trigger conditions. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an input. Bit 0 corr… |
| 1.3.6.1.4.1.5040.1.2.4.3.1.5.3.1.2 | ColumnwtWebioEA12x12AlarmOutputTrigger | read-write | mandatory | This variable allows setting of individual output trigger conditions. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 co… |
| 1.3.6.1.4.1.5040.1.2.4.3.1.5.3.1.3 | ColumnwtWebioEA12x12AlarmSystemTrigger | read-write | mandatory | Binary coded trigger conditions: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, … |
| 1.3.6.1.4.1.5040.1.2.4.3.1.5.3.1.4 | ColumnwtWebioEA12x12AlarmMaxCounterValue | read-write | mandatory | This variable configures a max. counter value. If an input counter value exceeds this max. value, the corresponding alarm is triggered. Input counters with its… |
| 1.3.6.1.4.1.5040.1.2.4.3.1.5.3.1.5 | ColumnwtWebioEA12x12AlarmInterval | read-write | mandatory | Send interval for alarm messages. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.5.3.1.6 | ColumnwtWebioEA12x12AlarmEnable | read-write | mandatory | Binary coded alarm enable: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Mail Enable Bit 1: SNMP Trap enable Bit 2: UDP enable Bit 3: Send in… |
| 1.3.6.1.4.1.5040.1.2.4.3.1.5.3.1.7 | ColumnwtWebioEA12x12AlarmMailAddr | read-write | mandatory | E-Mail address for sending the alarm mail to. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.5.3.1.8 | ColumnwtWebioEA12x12AlarmMailSubject | read-write | mandatory | Subject line for alarm mail. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.5.3.1.9 | ColumnwtWebioEA12x12AlarmMailText | read-write | mandatory | Alarm mail text: States of the Webio device can be included by using special tags. Please refer to the respective Webio manual |
| 1.3.6.1.4.1.5040.1.2.4.3.1.5.3.1.10 | ColumnwtWebioEA12x12AlarmSnmpManagerIP | read-write | mandatory | IP address of the SNMP Manager to which the Webio device should send SNMP traps. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.5.3.1.11 | ColumnwtWebioEA12x12AlarmSnmpTrapText | read-write | mandatory | This text appears in the trap body. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.5.3.1.12 | ColumnwtWebioEA12x12AlarmUdpIpAddr | read-write | mandatory | IP address of the UDP listener to which the Webio device should send UDP traps. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.5.3.1.13 | ColumnwtWebioEA12x12AlarmUdpPort | read-write | mandatory | Port number of the UDP listener to which the Webio device should send UDP traps. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.5.3.1.14 | ColumnwtWebioEA12x12AlarmUdpText | read-write | mandatory | This text appears in the UDP trap body. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.5.3.1.15 | ColumnwtWebioEA12x12AlarmTcpIpAddr | read-write | mandatory | IP address of the TCP listener to which the Webio device should send TCP traps. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.5.3.1.16 | ColumnwtWebioEA12x12AlarmTcpPort | read-write | mandatory | Port number of the TCP listener to which the Webio device should send TCP traps. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.5.3.1.17 | ColumnwtWebioEA12x12AlarmTcpText | read-write | mandatory | This text appears in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.5.3.1.18 | ColumnwtWebioEA12x12AlarmSyslogIpAddr | read-write | mandatory | IP address of the syslog server to which the Webio device should send syslog messages. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.5.3.1.19 | ColumnwtWebioEA12x12AlarmSyslogPort | read-write | mandatory | Port number of the syslog server to which the Webio device should send syslog messages. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.5.3.1.20 | ColumnwtWebioEA12x12AlarmSyslogText | read-write | mandatory | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.5.3.1.21 | ColumnwtWebioEA12x12AlarmFtpDataPort | read-write | mandatory | Local data port: 1..65535 or AUTO: the next free port will be assigned. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.5.3.1.22 | ColumnwtWebioEA12x12AlarmFtpFileName | read-write | mandatory | Name of the file including path informations. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.5.3.1.23 | ColumnwtWebioEA12x12AlarmFtpText | read-write | mandatory | Message text to store on the FTP server. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.5.3.1.24 | ColumnwtWebioEA12x12AlarmFtpOption | read-write | mandatory | Binary coded options, select only one option at the same time: STORE = replace file APPEND = append message at the end of the file Octet 1: unused Octet 2: unu… |
| 1.3.6.1.4.1.5040.1.2.4.3.1.5.3.1.25 | ColumnwtWebioEA12x12AlarmTimerCron | read-write | mandatory | This entry contains 5 space or tab seperated text fields for time trigger definition. Each field must match with the actual time to trigger a message, weekday … |
| 1.3.6.1.4.1.5040.1.2.4.3.1.5.3.1.26 | ColumnwtWebioEA12x12AlarmMailReleaseSubject | read-write | mandatory | Subject line for alarm mail. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.5.3.1.27 | ColumnwtWebioEA12x12AlarmMailReleaseText | read-write | mandatory | Release Alarm mail text: States of the Webio device can be included by using special tags. Please refer to the respective Webio manual |
| 1.3.6.1.4.1.5040.1.2.4.3.1.5.3.1.28 | ColumnwtWebioEA12x12AlarmSnmpTrapReleaseText | read-write | mandatory | This text appears in the trap body. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.5.3.1.29 | ColumnwtWebioEA12x12AlarmUdpReleaseText | read-write | mandatory | This text appears in the UDP trap body. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.5.3.1.30 | ColumnwtWebioEA12x12AlarmTcpReleaseText | read-write | mandatory | This text appears in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.5.3.1.31 | ColumnwtWebioEA12x12AlarmSyslogReleaseText | read-write | mandatory | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.5.3.1.32 | ColumnwtWebioEA12x12AlarmFtpReleaseText | read-write | mandatory | Message text to store on the FTP server. |
| 1.3.6.1.4.1.5040.1.2.4.3.1.5.4 | ScalarwtWebioEA12x12LoadControlView | read-only | mandatory | Here the result of automatic load control can be read. All output were tested in pairs (0-1, 2-3, 4-5, 6-7, 8-9, 10-11). If an error occours at one output, bot… |
| 1.3.6.1.4.1.5040.1.2.4.3.1.5.5 | ScalarwtWebioEA12x12LCShutDownView | read-write | mandatory | Here the result of the automatic load control shut down can be read. All outputs remain switched of, until a zero is written into this variable. But previously… |
| 1.3.6.1.4.1.5040.1.2.4.3.2 | NodewtWebioEA12x12Ports | |||
| 1.3.6.1.4.1.5040.1.2.4.3.2.1 | TablewtWebioEA12x12InputPortTable | not-accessible | mandatory | List of settings depending on the input number. |
| 1.3.6.1.4.1.5040.1.2.4.3.2.1.1 | RowwtWebioEA12x12InputPortEntry | not-accessible | mandatory | Input parameter for the individual inputs. |
| 1.3.6.1.4.1.5040.1.2.4.3.2.1.1.1 | ColumnwtWebioEA12x12PortInputName | read-write | mandatory | Name of the input. |
| 1.3.6.1.4.1.5040.1.2.4.3.2.1.1.2 | ColumnwtWebioEA12x12PortInputText | read-write | mandatory | Description of the input. |
| 1.3.6.1.4.1.5040.1.2.4.3.2.1.1.3 | ColumnwtWebioEA12x12PortInputMode | read-write | mandatory | Binary coded modes: Selecting short pulse detection enable by setting the corresponding bit to 1 enables interrupt support for counting. Only positive edges ar… |
| 1.3.6.1.4.1.5040.1.2.4.3.2.1.1.4 | ColumnwtWebioEA12x12PortInputFilter | read-write | mandatory | Pulses with a duration shorter than here specified (duration in 1/1000 sec), are ignored. |
| 1.3.6.1.4.1.5040.1.2.4.3.2.1.1.5 | ColumnwtWebioEA12x12PortInputBicountPulsePolarity | read-write | mandatory | This value defines the polarity of the input pulse. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 0 : negative polarity Bit 1 : positive polarit… |
| 1.3.6.1.4.1.5040.1.2.4.3.2.1.1.6 | ColumnwtWebioEA12x12PortInputBicountInactivTimeout | read-write | mandatory | Pulse chains with a duration shorter than here specified (in 1/10 sek), are ignored. |
| 1.3.6.1.4.1.5040.1.2.4.3.2.2 | TablewtWebioEA12x12OutputPortTable | not-accessible | mandatory | List of settings depending on the output number. |
| 1.3.6.1.4.1.5040.1.2.4.3.2.2.1 | RowwtWebioEA12x12OutputPortEntry | not-accessible | mandatory | Output parameters of the individual outputs. |
| 1.3.6.1.4.1.5040.1.2.4.3.2.2.1.1 | ColumnwtWebioEA12x12PortOutputName | read-write | mandatory | Name of the output. |
| 1.3.6.1.4.1.5040.1.2.4.3.2.2.1.2 | ColumnwtWebioEA12x12PortOutputText | read-write | mandatory | Description of the output. |
| 1.3.6.1.4.1.5040.1.2.4.3.2.2.1.3 | ColumnwtWebioEA12x12PortOutputGroupMode | read-write | mandatory | It is possible to connect outputs together to increase the output current. This could be done by connecting 2 or 4 outputs in a group together. All bits of suc… |
| 1.3.6.1.4.1.5040.1.2.4.3.2.2.1.4 | ColumnwtWebioEA12x12PortOutputSafetyState | read-write | mandatory | This variable allows setting of individual digital outputs. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds … |
| 1.3.6.1.4.1.5040.1.2.4.3.2.2.1.5 | ColumnwtWebioEA12x12PortLogicInputMask | read-write | mandatory | Selecting one of these inputs by setting the corresponding bit to 1 enables the logic function for the output identified by the index within this table. The ca… |
| 1.3.6.1.4.1.5040.1.2.4.3.2.2.1.6 | ColumnwtWebioEA12x12PortLogicInputInverter | read-write | mandatory | Every input bit selected here will be inverted. OCTET 1: unused OCTET 2: unused OCTET 3: Bit 0-3 : inputs 8-11 Bit 4-7 : unused OCTET 4: Bit 0-7 : inputs 0-7 |
| 1.3.6.1.4.1.5040.1.2.4.3.2.2.1.7 | ColumnwtWebioEA12x12PortLogicFunction | read-write | mandatory | This determines the logic function. No more than one function may be selected. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 0 : logic function … |
| 1.3.6.1.4.1.5040.1.2.4.3.2.2.1.8 | ColumnwtWebioEA12x12PortLogicOutputInverter | read-write | mandatory | The logical operation result could be inverteted by setting the corresponding bit to 1. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 0 : Output… |
| 1.3.6.1.4.1.5040.1.2.4.3.2.2.1.9 | ColumnwtWebioEA12x12PortPulseDuration | read-write | mandatory | Pulse length in 1/1000 sec. Setting this value to zero, disables the pulse output. |
| 1.3.6.1.4.1.5040.1.2.4.3.2.2.1.10 | ColumnwtWebioEA12x12PortPulsePolarity | read-write | mandatory | This value defines the polarity of the output pulse, if wtWebioEA12x12PortPulseDuration is not set to zero. After the pulse is finished, the output switches ba… |
| 1.3.6.1.4.1.5040.1.2.4.3.3 | NodewtWebioEA12x12Manufact | |||
| 1.3.6.1.4.1.5040.1.2.4.3.3.1 | ScalarwtWebioEA12x12MfName | read-write | mandatory | Manufacturer company name |
| 1.3.6.1.4.1.5040.1.2.4.3.3.2 | ScalarwtWebioEA12x12MfAddr | read-write | mandatory | Manufacturer address. |
| 1.3.6.1.4.1.5040.1.2.4.3.3.3 | ScalarwtWebioEA12x12MfHotline | read-write | mandatory | Manufacturer hotline. |
| 1.3.6.1.4.1.5040.1.2.4.3.3.4 | ScalarwtWebioEA12x12MfInternet | read-write | mandatory | Manufacturer Internet address. |
| 1.3.6.1.4.1.5040.1.2.4.3.3.5 | ScalarwtWebioEA12x12MfDeviceTyp | read-write | mandatory | Manufacturer device name (model number). |
| 1.3.6.1.4.1.5040.1.2.4.4 | NodewtWebioEA12x12Diag | |||
| 1.3.6.1.4.1.5040.1.2.4.4.1 | ScalarwtWebioEA12x12DiagErrorCount | read-only | mandatory | Number of entries in the error memory. |
| 1.3.6.1.4.1.5040.1.2.4.4.2 | ScalarwtWebioEA12x12DiagBinaryError | read-only | mandatory | Error causes coded bit-by-bit. |
| 1.3.6.1.4.1.5040.1.2.4.4.3 | ScalarwtWebioEA12x12DiagErrorIndex | read-write | mandatory | The value of this variable is used as an index to read an error massege from wtWebioEA12x12DiagErrorMessage. Errors are numbered from 1 to wtWebioEA12x12DiagEr… |
| 1.3.6.1.4.1.5040.1.2.4.4.4 | ScalarwtWebioEA12x12DiagErrorMessage | read-only | mandatory | Using wtWebioEA12x12DiagErrorIndex as an index, the appropriate message is available. |
| 1.3.6.1.4.1.5040.1.2.4.4.5 | ScalarwtWebioEA12x12DiagErrorClear | write-only | mandatory | Writing 1 into this variable clears all diagnosis messages. |
| 1.3.6.1.4.1.5040.1.2.4.41 | NodewtWebioEA12x12Alert1 | This SNMP trap is generated when Alarm 1 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.4.42 | NodewtWebioEA12x12Alert2 | This SNMP trap is generated when Alarm 2 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.4.43 | NodewtWebioEA12x12Alert3 | This SNMP trap is generated when Alarm 3 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.4.44 | NodewtWebioEA12x12Alert4 | This SNMP trap is generated when Alarm 4 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.4.45 | NodewtWebioEA12x12Alert5 | This SNMP trap is generated when Alarm 5 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.4.46 | NodewtWebioEA12x12Alert6 | This SNMP trap is generated when Alarm 6 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.4.47 | NodewtWebioEA12x12Alert7 | This SNMP trap is generated when Alarm 7 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.4.48 | NodewtWebioEA12x12Alert8 | This SNMP trap is generated when Alarm 8 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.4.49 | NodewtWebioEA12x12Alert9 | This SNMP trap is generated when Alarm 9 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.4.50 | NodewtWebioEA12x12Alert10 | This SNMP trap is generated when Alarm 10 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.4.51 | NodewtWebioEA12x12Alert11 | This SNMP trap is generated when Alarm 11 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.4.52 | NodewtWebioEA12x12Alert12 | This SNMP trap is generated when Alarm 12 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.4.71 | NodewtWebioEA12x12Alert13 | This SNMP trap is generated when Alarm 1 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.4.72 | NodewtWebioEA12x12Alert14 | This SNMP trap is generated when Alarm 2 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.4.73 | NodewtWebioEA12x12Alert15 | This SNMP trap is generated when Alarm 3 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.4.74 | NodewtWebioEA12x12Alert16 | This SNMP trap is generated when Alarm 4 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.4.75 | NodewtWebioEA12x12Alert17 | This SNMP trap is generated when Alarm 5 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.4.76 | NodewtWebioEA12x12Alert18 | This SNMP trap is generated when Alarm 6 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.4.77 | NodewtWebioEA12x12Alert19 | This SNMP trap is generated when Alarm 7 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.4.78 | NodewtWebioEA12x12Alert20 | This SNMP trap is generated when Alarm 8 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.4.79 | NodewtWebioEA12x12Alert21 | This SNMP trap is generated when Alarm 9 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.4.80 | NodewtWebioEA12x12Alert22 | This SNMP trap is generated when Alarm 10 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.4.81 | NodewtWebioEA12x12Alert23 | This SNMP trap is generated when Alarm 11 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.4.82 | NodewtWebioEA12x12Alert24 | This SNMP trap is generated when Alarm 12 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.4.110 | NodewtWebioEA12x12AlertDiag | This SNMP trap is generated when a diagnosis/error message was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.13 | NodewtWebioEA2x2 | |||
| 1.3.6.1.4.1.5040.1.2.13.1 | NodewtWebioEA2x2InOut | |||
| 1.3.6.1.4.1.5040.1.2.13.1.1 | ScalarwtWebioEA2x2Inputs | read-only | mandatory | Number of idependent inputs. |
| 1.3.6.1.4.1.5040.1.2.13.1.2 | ScalarwtWebioEA2x2Outputs | read-only | mandatory | Number of idependent outputs. |
| 1.3.6.1.4.1.5040.1.2.13.1.3 | TablewtWebioEA2x2InputTable | not-accessible | mandatory | List of input indices. |
| 1.3.6.1.4.1.5040.1.2.13.1.3.1 | RowwtWebioEA2x2InputEntry | not-accessible | mandatory | Number of the inputs. |
| 1.3.6.1.4.1.5040.1.2.13.1.3.1.1 | ColumnwtWebioEA2x2InputNo | read-only | mandatory | Index numbers of the inputs. |
| 1.3.6.1.4.1.5040.1.2.13.1.3.1.2 | ColumnwtWebioEA2x2InputCounter | read-only | mandatory | Value of the input counter. |
| 1.3.6.1.4.1.5040.1.2.13.1.3.1.3 | ColumnwtWebioEA2x2InputCounterClear | read-only | mandatory | Clears the input counter after returning its value. |
| 1.3.6.1.4.1.5040.1.2.13.1.3.1.4 | ColumnwtWebioEA2x2InputState | read-only | mandatory | Value of a single input bit, 0-OFF, 1-ON. |
| 1.3.6.1.4.1.5040.1.2.13.1.4 | ScalarwtWebioEA2x2InputValue | read-only | mandatory | This variable is used to read the inputs of the digital I/O port. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corres… |
| 1.3.6.1.4.1.5040.1.2.13.1.5 | TablewtWebioEA2x2OutputTable | not-accessible | mandatory | List of output indices. |
| 1.3.6.1.4.1.5040.1.2.13.1.5.1 | RowwtWebioEA2x2OutputEntry | not-accessible | mandatory | Number of the outputs. |
| 1.3.6.1.4.1.5040.1.2.13.1.5.1.1 | ColumnwtWebioEA2x2OutputNo | read-only | mandatory | Output number. |
| 1.3.6.1.4.1.5040.1.2.13.1.5.1.2 | ColumnwtWebioEA2x2OutputState | read-write | mandatory | Value of a single output bit, 0-OFF, 1-ON. |
| 1.3.6.1.4.1.5040.1.2.13.1.6 | ScalarwtWebioEA2x2OutputValue | read-write | mandatory | This variable is used to read and write the outputs of the digital I/O port. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. B… |
| 1.3.6.1.4.1.5040.1.2.13.1.7 | ScalarwtWebioEA2x2SetOutput | read-write | mandatory | This variable allows setting of individual digital outputs. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds … |
| 1.3.6.1.4.1.5040.1.2.13.2 | NodewtWebioEA2x2SessCntrl | |||
| 1.3.6.1.4.1.5040.1.2.13.2.1 | ScalarwtWebioEA2x2SessCntrlPassword | read-write | mandatory | Entering this password opens a session which is ended by writing a 1 to wtWebioEA2x2SessCntrlLogout. When read this variable provides a string of length zero. |
| 1.3.6.1.4.1.5040.1.2.13.2.2 | ScalarwtWebioEA2x2SessCntrlConfigMode | read-only | mandatory | When the device is in SNMP configuration mode, the value 1 is returned, otherwise 0. If the read value is 0 even though the password was written, the device is… |
| 1.3.6.1.4.1.5040.1.2.13.2.3 | ScalarwtWebioEA2x2SessCntrlLogout | read-write | mandatory | If the device is in configuration mode and the session was opened by this SNMP Manager, writing a 1 to this variable will end the session and all parameters ar… |
| 1.3.6.1.4.1.5040.1.2.13.2.4 | ScalarwtWebioEA2x2SessCntrlAdminPassword | read-write | mandatory | This password protects access to the variables with administrator rights. It can only be changed by the administrator. If no password was assigned, the valid p… |
| 1.3.6.1.4.1.5040.1.2.13.2.5 | ScalarwtWebioEA2x2SessCntrlConfigPassword | read-write | mandatory | This password protects access to the variables with configurator rights. It can be changed by the administrator and by the configurator. If no password was ass… |
| 1.3.6.1.4.1.5040.1.2.13.3 | NodewtWebioEA2x2Config | |||
| 1.3.6.1.4.1.5040.1.2.13.3.1 | NodewtWebioEA2x2Device | |||
| 1.3.6.1.4.1.5040.1.2.13.3.1.1 | NodewtWebioEA2x2Text | |||
| 1.3.6.1.4.1.5040.1.2.13.3.1.1.1 | ScalarwtWebioEA2x2DeviceName | read-write | mandatory | Name of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.1.2 | ScalarwtWebioEA2x2DeviceText | read-write | mandatory | Description of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.1.3 | ScalarwtWebioEA2x2DeviceLocation | read-write | mandatory | Description of the location of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.1.4 | ScalarwtWebioEA2x2DeviceContact | read-write | mandatory | Contact address of the system operator of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.2 | NodewtWebioEA2x2TimeDate | |||
| 1.3.6.1.4.1.5040.1.2.13.3.1.2.1 | NodewtWebioEA2x2TimeZone | |||
| 1.3.6.1.4.1.5040.1.2.13.3.1.2.1.1 | ScalarwtWebioEA2x2TzOffsetHrs | read-write | mandatory | Offset hours for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.2.1.2 | ScalarwtWebioEA2x2TzOffsetMin | read-write | mandatory | Offset minutes for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.2.1.3 | ScalarwtWebioEA2x2TzEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Timezone |
| 1.3.6.1.4.1.5040.1.2.13.3.1.2.1.4 | ScalarwtWebioEA2x2StTzOffsetHrs | read-write | mandatory | Offset hours of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.2.1.5 | ScalarwtWebioEA2x2StTzOffsetMin | read-write | mandatory | Offset minutes of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.2.1.6 | ScalarwtWebioEA2x2StTzEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Summertime |
| 1.3.6.1.4.1.5040.1.2.13.3.1.2.1.7 | ScalarwtWebioEA2x2StTzStartMonth | read-write | mandatory | Month in which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.2.1.8 | ScalarwtWebioEA2x2StTzStartMode | read-write | mandatory | Mode of the day of the week for which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.2.1.9 | ScalarwtWebioEA2x2StTzStartWday | read-write | mandatory | Day of the week on which the change is made from winter time to summer time |
| 1.3.6.1.4.1.5040.1.2.13.3.1.2.1.10 | ScalarwtWebioEA2x2StTzStartHrs | read-write | mandatory | Hour in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.2.1.11 | ScalarwtWebioEA2x2StTzStartMin | read-write | mandatory | Minute in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.2.1.12 | ScalarwtWebioEA2x2StTzStopMonth | read-write | mandatory | Month in which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.2.1.13 | ScalarwtWebioEA2x2StTzStopMode | read-write | mandatory | Mode of the week day on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.2.1.14 | ScalarwtWebioEA2x2StTzStopWday | read-write | mandatory | Day of the week on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.2.1.15 | ScalarwtWebioEA2x2StTzStopHrs | read-write | mandatory | Hour at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.2.1.16 | ScalarwtWebioEA2x2StTzStopMin | read-write | mandatory | Minute at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.2.2 | NodewtWebioEA2x2TimeServer | |||
| 1.3.6.1.4.1.5040.1.2.13.3.1.2.2.1 | ScalarwtWebioEA2x2TimeServer1 | read-write | mandatory | IP address or name of the 1st time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.13.3.1.2.2.2 | ScalarwtWebioEA2x2TimeServer2 | read-write | mandatory | IP address or name of the 2nd time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.13.3.1.2.2.3 | ScalarwtWebioEA2x2TsEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Time Server |
| 1.3.6.1.4.1.5040.1.2.13.3.1.2.2.4 | ScalarwtWebioEA2x2TsSyncTime | read-write | mandatory | Daily synchronisation time with the time server (hour: 0-23). |
| 1.3.6.1.4.1.5040.1.2.13.3.1.2.3 | NodewtWebioEA2x2DeviceClock | |||
| 1.3.6.1.4.1.5040.1.2.13.3.1.2.3.1 | ScalarwtWebioEA2x2ClockHrs | read-write | mandatory | Clock hours taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.2.3.2 | ScalarwtWebioEA2x2ClockMin | read-write | mandatory | Clock minutes taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.2.3.3 | ScalarwtWebioEA2x2ClockDay | read-write | mandatory | Date: Day of the month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.2.3.4 | ScalarwtWebioEA2x2ClockMonth | read-write | mandatory | Date: Month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.2.3.5 | ScalarwtWebioEA2x2ClockYear | read-write | mandatory | Date: Year, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3 | NodewtWebioEA2x2Basic | |||
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.1 | NodewtWebioEA2x2Network | |||
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.1.1 | ScalarwtWebioEA2x2IpAddress | read-write | mandatory | IP address of the Webio |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.1.2 | ScalarwtWebioEA2x2SubnetMask | read-write | mandatory | Subnet mask of the Webio |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.1.3 | ScalarwtWebioEA2x2Gateway | read-write | mandatory | Gateway of the Webio |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.1.4 | ScalarwtWebioEA2x2DnsServer1 | read-write | mandatory | IP address of the 1st DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.1.5 | ScalarwtWebioEA2x2DnsServer2 | read-write | mandatory | IP address of the 2nd DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.1.6 | ScalarwtWebioEA2x2AddConfig | read-write | mandatory | Additional configuration (1=ON): Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1: DHCP enable Bit 0: BOOTP enable |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.2 | NodewtWebioEA2x2HTTP | |||
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.2.1 | ScalarwtWebioEA2x2Startup | read-write | mandatory | Binary coded start page, more than one page must not be selected: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 2: user.htm Bit 1: home.htm Bit … |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.2.2 | ScalarwtWebioEA2x2GetHeaderEnable | read-write | mandatory | If bits are set, every answer of a short form GET question will be lead by the IP-address and name of the device (Header) or a HTTP header (HTTP): Octet 1: unu… |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.2.3 | ScalarwtWebioEA2x2HttpInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.2.4 | ScalarwtWebioEA2x2HttpPort | read-write | mandatory | Definition of the standard HTML port (Default: 80). |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.3 | NodewtWebioEA2x2Mail | |||
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.3.1 | ScalarwtWebioEA2x2MailAdName | read-write | mandatory | Device name for mail administration. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.3.2 | ScalarwtWebioEA2x2MailReply | read-write | mandatory | Reply address for the mail server. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.3.3 | ScalarwtWebioEA2x2MailServer | read-write | mandatory | Name or IP address of the mail server. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.3.4 | ScalarwtWebioEA2x2MailEnable | read-write | mandatory | Set this bit to enable the sending of mails: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Mail enable |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.3.5 | ScalarwtWebioEA2x2MailAuthentication | read-write | mandatory | Selection of the authentication modi: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTE… |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.3.6 | ScalarwtWebioEA2x2MailAuthUser | read-write | mandatory | Name of the user to be authenticated. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.3.7 | ScalarwtWebioEA2x2MailAuthPassword | read-write | mandatory | Authentication password. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.3.8 | ScalarwtWebioEA2x2MailPop3Server | read-write | mandatory | Name or Ip-address of the POP3 Servers. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.4 | NodewtWebioEA2x2SNMP | |||
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.4.1 | ScalarwtWebioEA2x2SnmpEnable | read-write | mandatory | Set bit 0 to enable SNMP. If disabled, the device did not respond to any SNMP requests. Bit 1 decided wether the community string of read operations is compare… |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.4.2 | ScalarwtWebioEA2x2SnmpCommunityStringRead | read-write | mandatory | Community string read only |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.4.3 | ScalarwtWebioEA2x2SnmpCommunityStringReadWrite | read-write | mandatory | Community string read / write |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.4.4 | ScalarwtWebioEA2x2SnmpSystemTrapManagerIP | read-write | mandatory | Name or IP address of the TCP server which accepts the system trap. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.4.5 | ScalarwtWebioEA2x2SnmpSystemTrapEnable | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2: Diag messages Bit 3-7: unused |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.5 | NodewtWebioEA2x2UDP | |||
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.5.1 | ScalarwtWebioEA2x2UdpAdminPort | read-write | mandatory | Udp port to which the Udp queries ( short form GET requests) can be sent. This port number must be unique within the device. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.5.2 | ScalarwtWebioEA2x2UdpEnable | read-write | mandatory | Set this bit to enable UDP support: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : UDP enable |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.5.3 | ScalarwtWebioEA2x2UdpRemotePort | read-write | mandatory | Udp remote port setting. If this value is set to zero, the source port read from a request will be used as destination port for the answer. A non zero value fo… |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.6 | NodewtWebioEA2x2Binary | |||
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.6.1 | ScalarwtWebioEA2x2BinaryModeCount | read-only | mandatory | Number of independent binary channels. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.6.2 | TablewtWebioEA2x2BinaryIfTable | not-accessible | mandatory | Table of indices. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.6.2.1 | RowwtWebioEA2x2BinaryIfEntry | not-accessible | mandatory | Indices of the binary channels. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.6.2.1.1 | ColumnwtWebioEA2x2BinaryModeNo | read-only | mandatory | Number of the binary channel. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.6.3 | TablewtWebioEA2x2BinaryTable | not-accessible | mandatory | Table of properties of the binary mode. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.6.3.1 | RowwtWebioEA2x2BinaryEntry | not-accessible | mandatory | Binary properties. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.6.3.1.1 | ColumnwtWebioEA2x2BinaryOperationMode | read-write | mandatory | Selection of the operation mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: … |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.6.3.1.2 | ColumnwtWebioEA2x2BinaryTcpServerLocalPort | read-write | mandatory | Local TCP port for data exchange in this server mode. This port number must be unique within the device. Reserved port number must not be used (refere to the m… |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.6.3.1.3 | ColumnwtWebioEA2x2BinaryTcpServerInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.6.3.1.4 | ColumnwtWebioEA2x2BinaryTcpServerApplicationMode | read-write | mandatory | Selection of the application mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4… |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.6.3.1.5 | ColumnwtWebioEA2x2BinaryTcpClientLocalPort | read-write | mandatory | Local TCP port for data exchange in this client mode. This port number must be unique within the device. Reserved port number must not be used (refere to the m… |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.6.3.1.6 | ColumnwtWebioEA2x2BinaryTcpClientServerPort | read-write | mandatory | Port number of the server. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when setting t… |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.6.3.1.7 | ColumnwtWebioEA2x2BinaryTcpClientServerIpAddr | read-write | mandatory | Ip address of the server. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when setting th… |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.6.3.1.8 | ColumnwtWebioEA2x2BinaryTcpClientServerPassword | read-write | mandatory | Building a connection may be protected by the administrator password of the server. Enter the server password to establish the connection, if a server administ… |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.6.3.1.9 | ColumnwtWebioEA2x2BinaryTcpClientInactivity | read-write | mandatory | Connection timeout in 100ms. If no data are exchanged within the specified time, the device closes the connection to the server. The value 0 deactivates the ti… |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.6.3.1.10 | ColumnwtWebioEA2x2BinaryTcpClientInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.6.3.1.11 | ColumnwtWebioEA2x2BinaryTcpClientInterval | read-write | mandatory | Configurable interval with a 100ms base, in which the Webio device sends data to the configured application. A interval of zero stopps the periodical sending. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.6.3.1.12 | ColumnwtWebioEA2x2BinaryTcpClientApplicationMode | read-write | mandatory | Selection of the application mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4… |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.6.3.1.13 | ColumnwtWebioEA2x2BinaryUdpPeerLocalPort | read-write | mandatory | Local UDP port for data exchange in this peer to peer mode. This port number must be unique within the device. Reserved port number must not be used (refere to… |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.6.3.1.14 | ColumnwtWebioEA2x2BinaryUdpPeerRemotePort | read-write | mandatory | Port number of the remote device. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when se… |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.6.3.1.15 | ColumnwtWebioEA2x2BinaryUdpPeerRemoteIpAddr | read-write | mandatory | Ip address of the remote device. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when set… |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.6.3.1.16 | ColumnwtWebioEA2x2BinaryUdpPeerInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.6.3.1.17 | ColumnwtWebioEA2x2BinaryUdpPeerInterval | read-write | mandatory | Configurable interval with a 100ms base, in which the Webio device sends data to the configured remote device. A interval of zero stopps the periodical sending. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.6.3.1.18 | ColumnwtWebioEA2x2BinaryUdpPeerApplicationMode | read-write | mandatory | Selection of the application mode: The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds to the LSB. OCTET 1: unus… |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.6.3.1.19 | ColumnwtWebioEA2x2BinaryConnectedPort | read-only | mandatory | Port number of the remote device, after connection has been established. In case of no connection or missing port informations a zero will be read. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.6.3.1.20 | ColumnwtWebioEA2x2BinaryConnectedIpAddr | read-only | mandatory | IP address of the remote device, after connection has been established. In case of no connection or missing port informations 0.0.0.0 will be read. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.6.3.1.21 | ColumnwtWebioEA2x2BinaryTcpServerClientHttpPort | read-write | mandatory | HTTP port number of the remote device at TCP Server Mode. If an mailfunction occurs status informations will be send to this port. Not used at mode Compatible … |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.6.3.1.22 | ColumnwtWebioEA2x2BinaryTcpClientServerHttpPort | read-write | mandatory | HTTP port number of the remote device at TCP Client Mode. In the operating mode Box2Box connection status informations will be exchanged through this port. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.7 | NodewtWebioEA2x2Syslog | |||
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.7.1 | ScalarwtWebioEA2x2SyslogServerIP | read-write | mandatory | Name or IP address of the Syslog server, which accepts the Syslog messgaes. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.7.2 | ScalarwtWebioEA2x2SyslogServerPort | read-write | mandatory | Portnumber of the Syslog servers, default 514. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.7.3 | ScalarwtWebioEA2x2SyslogSystemMessagesEnable | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2: Diag Messages Bit 3-7: unused |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.7.4 | ScalarwtWebioEA2x2SyslogEnable | read-write | mandatory | Set bit 0to enable Syslog: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Syslog enable |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.8 | NodewtWebioEA2x2FTP | |||
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.8.1 | ScalarwtWebioEA2x2FTPServerIP | read-write | mandatory | Name or IP address of the FTP server, which accepts the FTP messages. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.8.2 | ScalarwtWebioEA2x2FTPServerControlPort | read-write | mandatory | Portnumber of the control port of the FTP server, default 21. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.8.3 | ScalarwtWebioEA2x2FTPUserName | read-write | mandatory | FTP Loggin: user name. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.8.4 | ScalarwtWebioEA2x2FTPPassword | read-write | mandatory | FTP Loggin: user password. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.8.5 | ScalarwtWebioEA2x2FTPAccount | read-write | mandatory | FTP Loggin: name of account. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.8.6 | ScalarwtWebioEA2x2FTPOption | read-write | mandatory | Bit 0 switches the FTP Server in Passiv-Mode, the Client controls the data connection on its own: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit … |
| 1.3.6.1.4.1.5040.1.2.13.3.1.3.8.7 | ScalarwtWebioEA2x2FTPEnable | read-write | mandatory | Set Bit 0 to enable FTP: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : FTP enable |
| 1.3.6.1.4.1.5040.1.2.13.3.1.4 | NodewtWebioEA2x2OutputMode | |||
| 1.3.6.1.4.1.5040.1.2.13.3.1.4.1 | TablewtWebioEA2x2OutputModeTable | not-accessible | mandatory | Table of output mode configurations dependent on the output indices. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.4.1.1 | RowwtWebioEA2x2OutputModeEntry | not-accessible | mandatory | Output mode configurations of the individual outputs. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.4.1.1.1 | ColumnwtWebioEA2x2OutputModeBit | read-write | mandatory | This binary coded output mode defines the individual operation mode for any output. More than one mode must not be selected. The OCTETS are interpreted bit-by-… |
| 1.3.6.1.4.1.5040.1.2.13.3.1.4.2 | ScalarwtWebioEA2x2SafetyTimeout | read-write | mandatory | After this period of time (multiple of 100ms) without receiving data outputs switch to their Safety States. For each output a independend safety state could be… |
| 1.3.6.1.4.1.5040.1.2.13.3.1.4.3 | ScalarwtWebioEA2x2LoadControlEnable | read-write | mandatory | Here the function of automatic load control can be enabled. All output were tested in pairs (0-1). If an error occours at one output, both output of an pair wi… |
| 1.3.6.1.4.1.5040.1.2.13.3.1.5 | NodewtWebioEA2x2Alarm | |||
| 1.3.6.1.4.1.5040.1.2.13.3.1.5.1 | ScalarwtWebioEA2x2AlarmCount | read-only | mandatory | Number of independent alarms. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.5.2 | TablewtWebioEA2x2AlarmIfTable | not-accessible | mandatory | List of alarm indices. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.5.2.1 | RowwtWebioEA2x2AlarmIfEntry | not-accessible | mandatory | Numbers of the alarms. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.5.2.1.1 | ColumnwtWebioEA2x2AlarmNo | read-only | mandatory | Numbers of the alarms. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.5.3 | TablewtWebioEA2x2AlarmTable | not-accessible | mandatory | List of settings depending on the alarm number. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.5.3.1 | RowwtWebioEA2x2AlarmEntry | not-accessible | mandatory | Alarm parameters of the individual alarms. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.5.3.1.1 | ColumnwtWebioEA2x2AlarmInputTrigger | read-write | mandatory | This variable allows setting of individual input trigger conditions. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an input. Bit 0 corr… |
| 1.3.6.1.4.1.5040.1.2.13.3.1.5.3.1.2 | ColumnwtWebioEA2x2AlarmOutputTrigger | read-write | mandatory | This variable allows setting of individual output trigger conditions. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 co… |
| 1.3.6.1.4.1.5040.1.2.13.3.1.5.3.1.3 | ColumnwtWebioEA2x2AlarmSystemTrigger | read-write | mandatory | Binary coded trigger conditions: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, … |
| 1.3.6.1.4.1.5040.1.2.13.3.1.5.3.1.4 | ColumnwtWebioEA2x2AlarmMaxCounterValue | read-write | mandatory | This variable configures a max. counter value. If an input counter value exceeds this max. value, the corresponding alarm is triggered. Input counters with its… |
| 1.3.6.1.4.1.5040.1.2.13.3.1.5.3.1.5 | ColumnwtWebioEA2x2AlarmInterval | read-write | mandatory | Send interval for alarm messages. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.5.3.1.6 | ColumnwtWebioEA2x2AlarmEnable | read-write | mandatory | Binary coded alarm enable: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Mail Enable Bit 1: SNMP Trap enable Bit 2: UDP enable Bit 3: Send in… |
| 1.3.6.1.4.1.5040.1.2.13.3.1.5.3.1.7 | ColumnwtWebioEA2x2AlarmMailAddr | read-write | mandatory | E-Mail address for sending the alarm mail to. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.5.3.1.8 | ColumnwtWebioEA2x2AlarmMailSubject | read-write | mandatory | Subject line for alarm mail. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.5.3.1.9 | ColumnwtWebioEA2x2AlarmMailText | read-write | mandatory | Alarm mail text: States of the Webio device can be included by using special tags. Please refer to the respective Webio manual |
| 1.3.6.1.4.1.5040.1.2.13.3.1.5.3.1.10 | ColumnwtWebioEA2x2AlarmSnmpManagerIP | read-write | mandatory | IP address of the SNMP Manager to which the Webio device should send SNMP traps. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.5.3.1.11 | ColumnwtWebioEA2x2AlarmSnmpTrapText | read-write | mandatory | This text appears in the trap body. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.5.3.1.12 | ColumnwtWebioEA2x2AlarmUdpIpAddr | read-write | mandatory | IP address of the UDP listener to which the Webio device should send UDP traps. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.5.3.1.13 | ColumnwtWebioEA2x2AlarmUdpPort | read-write | mandatory | Port number of the UDP listener to which the Webio device should send UDP traps. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.5.3.1.14 | ColumnwtWebioEA2x2AlarmUdpText | read-write | mandatory | This text appears in the UDP trap body. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.5.3.1.15 | ColumnwtWebioEA2x2AlarmTcpIpAddr | read-write | mandatory | IP address of the TCP listener to which the Webio device should send TCP traps. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.5.3.1.16 | ColumnwtWebioEA2x2AlarmTcpPort | read-write | mandatory | Port number of the TCP listener to which the Webio device should send TCP traps. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.5.3.1.17 | ColumnwtWebioEA2x2AlarmTcpText | read-write | mandatory | This text appears in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.5.3.1.18 | ColumnwtWebioEA2x2AlarmSyslogIpAddr | read-write | mandatory | IP address of the syslog server to which the Webio device should send syslog messages. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.5.3.1.19 | ColumnwtWebioEA2x2AlarmSyslogPort | read-write | mandatory | Port number of the syslog server to which the Webio device should send syslog messages. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.5.3.1.20 | ColumnwtWebioEA2x2AlarmSyslogText | read-write | mandatory | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.5.3.1.21 | ColumnwtWebioEA2x2AlarmFtpDataPort | read-write | mandatory | Local data port: 1..65535 or AUTO: the next free port will be assigned. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.5.3.1.22 | ColumnwtWebioEA2x2AlarmFtpFileName | read-write | mandatory | Name of the file including path informations. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.5.3.1.23 | ColumnwtWebioEA2x2AlarmFtpText | read-write | mandatory | Message text to store on the FTP server. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.5.3.1.24 | ColumnwtWebioEA2x2AlarmFtpOption | read-write | mandatory | Binary coded options, select only one option at the same time: STORE = replace file APPEND = append message at the end of the file Octet 1: unused Octet 2: unu… |
| 1.3.6.1.4.1.5040.1.2.13.3.1.5.3.1.25 | ColumnwtWebioEA2x2AlarmTimerCron | read-write | mandatory | This entry contains 5 space or tab seperated text fields for time trigger definition. Each field must match with the actual time to trigger a message, weekday … |
| 1.3.6.1.4.1.5040.1.2.13.3.1.5.3.1.26 | ColumnwtWebioEA2x2AlarmMailReleaseSubject | read-write | mandatory | Subject line for alarm mail. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.5.3.1.27 | ColumnwtWebioEA2x2AlarmMailReleaseText | read-write | mandatory | Release Alarm mail text: States of the Webio device can be included by using special tags. Please refer to the respective Webio manual |
| 1.3.6.1.4.1.5040.1.2.13.3.1.5.3.1.28 | ColumnwtWebioEA2x2AlarmSnmpTrapReleaseText | read-write | mandatory | This text appears in the trap body. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.5.3.1.29 | ColumnwtWebioEA2x2AlarmUdpReleaseText | read-write | mandatory | This text appears in the UDP trap body. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.5.3.1.30 | ColumnwtWebioEA2x2AlarmTcpReleaseText | read-write | mandatory | This text appears in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.5.3.1.31 | ColumnwtWebioEA2x2AlarmSyslogReleaseText | read-write | mandatory | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.5.3.1.32 | ColumnwtWebioEA2x2AlarmFtpReleaseText | read-write | mandatory | Message text to store on the FTP server. |
| 1.3.6.1.4.1.5040.1.2.13.3.1.5.4 | ScalarwtWebioEA2x2LoadControlView | read-only | mandatory | Here the result of automatic load control can be read. All output were tested in pairs (0-1). If an error occours at one output, both output of an pair will be… |
| 1.3.6.1.4.1.5040.1.2.13.3.1.5.5 | ScalarwtWebioEA2x2LCShutDownView | read-write | mandatory | Here the result of the automatic load control shut down can be read. All outputs remain switched of, until a zero is written into this variable. But previously… |
| 1.3.6.1.4.1.5040.1.2.13.3.2 | NodewtWebioEA2x2Ports | |||
| 1.3.6.1.4.1.5040.1.2.13.3.2.1 | TablewtWebioEA2x2InputPortTable | not-accessible | mandatory | List of settings depending on the input number. |
| 1.3.6.1.4.1.5040.1.2.13.3.2.1.1 | RowwtWebioEA2x2InputPortEntry | not-accessible | mandatory | Input parameter for the individual inputs. |
| 1.3.6.1.4.1.5040.1.2.13.3.2.1.1.1 | ColumnwtWebioEA2x2PortInputName | read-write | mandatory | Name of the input. |
| 1.3.6.1.4.1.5040.1.2.13.3.2.1.1.2 | ColumnwtWebioEA2x2PortInputText | read-write | mandatory | Description of the input. |
| 1.3.6.1.4.1.5040.1.2.13.3.2.1.1.3 | ColumnwtWebioEA2x2PortInputMode | read-write | mandatory | Binary coded modes: Selecting short pulse detection enable by setting the corresponding bit to 1 enables interrupt support for counting. Only positive edges ar… |
| 1.3.6.1.4.1.5040.1.2.13.3.2.1.1.4 | ColumnwtWebioEA2x2PortInputFilter | read-write | mandatory | Pulses with a duration shorter than here specified (duration in 1/1000 sec), are ignored. |
| 1.3.6.1.4.1.5040.1.2.13.3.2.1.1.5 | ColumnwtWebioEA2x2PortInputBicountPulsePolarity | read-write | mandatory | This value defines the polarity of the input pulse. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 0 : negative polarity Bit 1 : positive polarit… |
| 1.3.6.1.4.1.5040.1.2.13.3.2.1.1.6 | ColumnwtWebioEA2x2PortInputBicountInactivTimeout | read-write | mandatory | Pulse chains with a duration shorter than here specified (in 1/10 sek), are ignored. |
| 1.3.6.1.4.1.5040.1.2.13.3.2.2 | TablewtWebioEA2x2OutputPortTable | not-accessible | mandatory | List of settings depending on the output number. |
| 1.3.6.1.4.1.5040.1.2.13.3.2.2.1 | RowwtWebioEA2x2OutputPortEntry | not-accessible | mandatory | Output parameters of the individual outputs. |
| 1.3.6.1.4.1.5040.1.2.13.3.2.2.1.1 | ColumnwtWebioEA2x2PortOutputName | read-write | mandatory | Name of the output. |
| 1.3.6.1.4.1.5040.1.2.13.3.2.2.1.2 | ColumnwtWebioEA2x2PortOutputText | read-write | mandatory | Description of the output. |
| 1.3.6.1.4.1.5040.1.2.13.3.2.2.1.3 | ColumnwtWebioEA2x2PortOutputGroupMode | read-write | mandatory | It is possible to connect outputs together to increase the output current. This could be done by connecting 2 or 4 outputs in a group together. All bits of suc… |
| 1.3.6.1.4.1.5040.1.2.13.3.2.2.1.4 | ColumnwtWebioEA2x2PortOutputSafetyState | read-write | mandatory | This variable allows setting of individual digital outputs. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds … |
| 1.3.6.1.4.1.5040.1.2.13.3.2.2.1.5 | ColumnwtWebioEA2x2PortLogicInputMask | read-write | mandatory | Selecting one of these inputs by setting the corresponding bit to 1 enables the logic function for the output identified by the index within this table. The ca… |
| 1.3.6.1.4.1.5040.1.2.13.3.2.2.1.6 | ColumnwtWebioEA2x2PortLogicInputInverter | read-write | mandatory | Every input bit selected here will be inverted. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 0-1 : inputs 0-1 |
| 1.3.6.1.4.1.5040.1.2.13.3.2.2.1.7 | ColumnwtWebioEA2x2PortLogicFunction | read-write | mandatory | This determines the logic function. No more than one function may be selected. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 0 : logic function … |
| 1.3.6.1.4.1.5040.1.2.13.3.2.2.1.8 | ColumnwtWebioEA2x2PortLogicOutputInverter | read-write | mandatory | The logical operation result could be inverteted by setting the corresponding bit to 1. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 0 : Output… |
| 1.3.6.1.4.1.5040.1.2.13.3.2.2.1.9 | ColumnwtWebioEA2x2PortPulseDuration | read-write | mandatory | Pulse length in 1/1000 sec. Setting this value to zero, disables the pulse output. |
| 1.3.6.1.4.1.5040.1.2.13.3.2.2.1.10 | ColumnwtWebioEA2x2PortPulsePolarity | read-write | mandatory | This value defines the polarity of the output pulse, if wtWebioEA2x2PortPulseDuration is not set to zero. After the pulse is finished, the output switches back… |
| 1.3.6.1.4.1.5040.1.2.13.3.3 | NodewtWebioEA2x2Manufact | |||
| 1.3.6.1.4.1.5040.1.2.13.3.3.1 | ScalarwtWebioEA2x2MfName | read-write | mandatory | Manufacturer company name |
| 1.3.6.1.4.1.5040.1.2.13.3.3.2 | ScalarwtWebioEA2x2MfAddr | read-write | mandatory | Manufacturer address. |
| 1.3.6.1.4.1.5040.1.2.13.3.3.3 | ScalarwtWebioEA2x2MfHotline | read-write | mandatory | Manufacturer hotline. |
| 1.3.6.1.4.1.5040.1.2.13.3.3.4 | ScalarwtWebioEA2x2MfInternet | read-write | mandatory | Manufacturer Internet address. |
| 1.3.6.1.4.1.5040.1.2.13.3.3.5 | ScalarwtWebioEA2x2MfDeviceTyp | read-write | mandatory | Manufacturer device name (model number). |
| 1.3.6.1.4.1.5040.1.2.13.4 | NodewtWebioEA2x2Diag | |||
| 1.3.6.1.4.1.5040.1.2.13.4.1 | ScalarwtWebioEA2x2DiagErrorCount | read-only | mandatory | Number of entries in the error memory. |
| 1.3.6.1.4.1.5040.1.2.13.4.2 | ScalarwtWebioEA2x2DiagBinaryError | read-only | mandatory | Error causes coded bit-by-bit. |
| 1.3.6.1.4.1.5040.1.2.13.4.3 | ScalarwtWebioEA2x2DiagErrorIndex | read-write | mandatory | The value of this variable is used as an index to read an error massege from wtWebioEA2x2DiagErrorMessage. Errors are numbered from 1 to wtWebioEA2x2DiagErrorC… |
| 1.3.6.1.4.1.5040.1.2.13.4.4 | ScalarwtWebioEA2x2DiagErrorMessage | read-only | mandatory | Using wtWebioEA2x2DiagErrorIndex as an index, the appropriate message is available. |
| 1.3.6.1.4.1.5040.1.2.13.4.5 | ScalarwtWebioEA2x2DiagErrorClear | write-only | mandatory | Writing 1 into this variable clears all diagnosis messages. |
| 1.3.6.1.4.1.5040.1.2.13.41 | NodewtWebioEA2x2Alert1 | This SNMP trap is generated when Alarm 1 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.13.42 | NodewtWebioEA2x2Alert2 | This SNMP trap is generated when Alarm 2 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.13.43 | NodewtWebioEA2x2Alert3 | This SNMP trap is generated when Alarm 3 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.13.44 | NodewtWebioEA2x2Alert4 | This SNMP trap is generated when Alarm 4 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.13.45 | NodewtWebioEA2x2Alert5 | This SNMP trap is generated when Alarm 5 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.13.46 | NodewtWebioEA2x2Alert6 | This SNMP trap is generated when Alarm 6 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.13.47 | NodewtWebioEA2x2Alert7 | This SNMP trap is generated when Alarm 7 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.13.48 | NodewtWebioEA2x2Alert8 | This SNMP trap is generated when Alarm 8 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.13.49 | NodewtWebioEA2x2Alert9 | This SNMP trap is generated when Alarm 9 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.13.50 | NodewtWebioEA2x2Alert10 | This SNMP trap is generated when Alarm 10 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.13.51 | NodewtWebioEA2x2Alert11 | This SNMP trap is generated when Alarm 11 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.13.52 | NodewtWebioEA2x2Alert12 | This SNMP trap is generated when Alarm 12 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.13.71 | NodewtWebioEA2x2Alert13 | This SNMP trap is generated when Alarm 1 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.13.72 | NodewtWebioEA2x2Alert14 | This SNMP trap is generated when Alarm 2 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.13.73 | NodewtWebioEA2x2Alert15 | This SNMP trap is generated when Alarm 3 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.13.74 | NodewtWebioEA2x2Alert16 | This SNMP trap is generated when Alarm 4 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.13.75 | NodewtWebioEA2x2Alert17 | This SNMP trap is generated when Alarm 5 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.13.76 | NodewtWebioEA2x2Alert18 | This SNMP trap is generated when Alarm 6 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.13.77 | NodewtWebioEA2x2Alert19 | This SNMP trap is generated when Alarm 7 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.13.78 | NodewtWebioEA2x2Alert20 | This SNMP trap is generated when Alarm 8 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.13.79 | NodewtWebioEA2x2Alert21 | This SNMP trap is generated when Alarm 9 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.13.80 | NodewtWebioEA2x2Alert22 | This SNMP trap is generated when Alarm 10 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.13.81 | NodewtWebioEA2x2Alert23 | This SNMP trap is generated when Alarm 11 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.13.82 | NodewtWebioEA2x2Alert24 | This SNMP trap is generated when Alarm 12 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.13.110 | NodewtWebioEA2x2AlertDiag | This SNMP trap is generated when a diagnosis/error message was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.14 | NodewtWebioEA24oem | |||
| 1.3.6.1.4.1.5040.1.2.14.1 | NodewtWebioEA24oemInOut | |||
| 1.3.6.1.4.1.5040.1.2.14.1.1 | ScalarwtWebioEA24oemInputs | read-only | mandatory | Number of independent inputs. |
| 1.3.6.1.4.1.5040.1.2.14.1.2 | ScalarwtWebioEA24oemOutputs | read-only | mandatory | Number of independent outputs. |
| 1.3.6.1.4.1.5040.1.2.14.1.3 | TablewtWebioEA24oemInputTable | not-accessible | mandatory | List of input indices. |
| 1.3.6.1.4.1.5040.1.2.14.1.3.1 | RowwtWebioEA24oemInputEntry | not-accessible | mandatory | Numbers of the inputs. |
| 1.3.6.1.4.1.5040.1.2.14.1.3.1.1 | ColumnwtWebioEA24oemInputNo | read-only | mandatory | Index numbers of the inputs. |
| 1.3.6.1.4.1.5040.1.2.14.1.3.1.2 | ColumnwtWebioEA24oemInputCounter | read-only | mandatory | Value of the input counter. |
| 1.3.6.1.4.1.5040.1.2.14.1.3.1.3 | ColumnwtWebioEA24oemInputCounterClear | read-only | mandatory | Value of the input counter. After reading this counter will be cleared. |
| 1.3.6.1.4.1.5040.1.2.14.1.3.1.4 | ColumnwtWebioEA24oemInputState | read-only | mandatory | Value of a single input bit, 0-OFF, 1-ON. |
| 1.3.6.1.4.1.5040.1.2.14.1.4 | ScalarwtWebioEA24oemInputValue | read-only | mandatory | This variable is used to read the inputs of the digital I/O port. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an input. Bit 0 corresp… |
| 1.3.6.1.4.1.5040.1.2.14.1.5 | TablewtWebioEA24oemOutputTable | not-accessible | mandatory | List of output indices. |
| 1.3.6.1.4.1.5040.1.2.14.1.5.1 | RowwtWebioEA24oemOutputEntry | not-accessible | mandatory | Numbers of the outputs. |
| 1.3.6.1.4.1.5040.1.2.14.1.5.1.1 | ColumnwtWebioEA24oemOutputNo | read-only | mandatory | Index numbers of the outputs. |
| 1.3.6.1.4.1.5040.1.2.14.1.5.1.2 | ColumnwtWebioEA24oemOutputState | read-write | mandatory | Value of a single output bit, 0-OFF, 1-ON. |
| 1.3.6.1.4.1.5040.1.2.14.1.6 | ScalarwtWebioEA24oemOutputValue | read-write | mandatory | This variable is used to read and write the outputs of the digital I/O port. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. B… |
| 1.3.6.1.4.1.5040.1.2.14.1.7 | ScalarwtWebioEA24oemSetOutput | read-write | mandatory | This variable allows setting of individual digital outputs. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds … |
| 1.3.6.1.4.1.5040.1.2.14.2 | NodewtWebioEA24oemSessCntrl | |||
| 1.3.6.1.4.1.5040.1.2.14.2.1 | ScalarwtWebioEA24oemSessCntrlPassword | read-write | mandatory | Entering this password opens a session which is ended by writing a 1 to wtWebioEA24oemSessCntrlLogout. When read this variable provides a string of length zero. |
| 1.3.6.1.4.1.5040.1.2.14.2.2 | ScalarwtWebioEA24oemSessCntrlConfigMode | read-only | mandatory | When the device is in SNMP configuration mode, the value 1 is returned, otherwise 0. If the read value is 0 even though the password was written, the device is… |
| 1.3.6.1.4.1.5040.1.2.14.2.3 | ScalarwtWebioEA24oemSessCntrlLogout | read-write | mandatory | If the device is in configuration mode and the session was opened by this SNMP Manager, writing a 1 to this variable will end the session and all parameters ar… |
| 1.3.6.1.4.1.5040.1.2.14.2.4 | ScalarwtWebioEA24oemSessCntrlAdminPassword | read-write | mandatory | This password protects access to the variables with administrator rights. It can only be changed by the administrator. If no password was assigned, the valid p… |
| 1.3.6.1.4.1.5040.1.2.14.2.5 | ScalarwtWebioEA24oemSessCntrlConfigPassword | read-write | mandatory | This password protects access to the variables with configurator rights. It can be changed by the administrator and by the configurator. If no password was ass… |
| 1.3.6.1.4.1.5040.1.2.14.3 | NodewtWebioEA24oemConfig | |||
| 1.3.6.1.4.1.5040.1.2.14.3.1 | NodewtWebioEA24oemDevice | |||
| 1.3.6.1.4.1.5040.1.2.14.3.1.1 | NodewtWebioEA24oemText | |||
| 1.3.6.1.4.1.5040.1.2.14.3.1.1.1 | ScalarwtWebioEA24oemDeviceName | read-write | mandatory | Name of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.1.2 | ScalarwtWebioEA24oemDeviceText | read-write | mandatory | Description of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.1.3 | ScalarwtWebioEA24oemDeviceLocation | read-write | mandatory | Description of the location of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.1.4 | ScalarwtWebioEA24oemDeviceContact | read-write | mandatory | Contact address of the system operator of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.2 | NodewtWebioEA24oemTimeDate | |||
| 1.3.6.1.4.1.5040.1.2.14.3.1.2.1 | NodewtWebioEA24oemTimeZone | |||
| 1.3.6.1.4.1.5040.1.2.14.3.1.2.1.1 | ScalarwtWebioEA24oemTzOffsetHrs | read-write | mandatory | Offset hours for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.2.1.2 | ScalarwtWebioEA24oemTzOffsetMin | read-write | mandatory | Offset minutes for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.2.1.3 | ScalarwtWebioEA24oemTzEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Timezone |
| 1.3.6.1.4.1.5040.1.2.14.3.1.2.1.4 | ScalarwtWebioEA24oemStTzOffsetHrs | read-write | mandatory | Offset hours of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.2.1.5 | ScalarwtWebioEA24oemStTzOffsetMin | read-write | mandatory | Offset minutes of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.2.1.6 | ScalarwtWebioEA24oemStTzEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Summertime |
| 1.3.6.1.4.1.5040.1.2.14.3.1.2.1.7 | ScalarwtWebioEA24oemStTzStartMonth | read-write | mandatory | Month in which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.2.1.8 | ScalarwtWebioEA24oemStTzStartMode | read-write | mandatory | Mode of the day of the week for which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.2.1.9 | ScalarwtWebioEA24oemStTzStartWday | read-write | mandatory | Day of the week on which the change is made from winter time to summer time |
| 1.3.6.1.4.1.5040.1.2.14.3.1.2.1.10 | ScalarwtWebioEA24oemStTzStartHrs | read-write | mandatory | Hour in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.2.1.11 | ScalarwtWebioEA24oemStTzStartMin | read-write | mandatory | Minute in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.2.1.12 | ScalarwtWebioEA24oemStTzStopMonth | read-write | mandatory | Month in which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.2.1.13 | ScalarwtWebioEA24oemStTzStopMode | read-write | mandatory | Mode of the week day on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.2.1.14 | ScalarwtWebioEA24oemStTzStopWday | read-write | mandatory | Day of the week on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.2.1.15 | ScalarwtWebioEA24oemStTzStopHrs | read-write | mandatory | Hour at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.2.1.16 | ScalarwtWebioEA24oemStTzStopMin | read-write | mandatory | Minute at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.2.2 | NodewtWebioEA24oemTimeServer | |||
| 1.3.6.1.4.1.5040.1.2.14.3.1.2.2.1 | ScalarwtWebioEA24oemTimeServer1 | read-write | mandatory | IP address or name of the 1st time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.14.3.1.2.2.2 | ScalarwtWebioEA24oemTimeServer2 | read-write | mandatory | IP address or name of the 2nd time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.14.3.1.2.2.3 | ScalarwtWebioEA24oemTsEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Time Server |
| 1.3.6.1.4.1.5040.1.2.14.3.1.2.2.4 | ScalarwtWebioEA24oemTsSyncTime | read-write | mandatory | Daily synchronisation time with the time server (hour: 0-23). |
| 1.3.6.1.4.1.5040.1.2.14.3.1.2.3 | NodewtWebioEA24oemDeviceClock | |||
| 1.3.6.1.4.1.5040.1.2.14.3.1.2.3.1 | ScalarwtWebioEA24oemClockHrs | read-write | mandatory | Clock hours taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.2.3.2 | ScalarwtWebioEA24oemClockMin | read-write | mandatory | Clock minutes taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.2.3.3 | ScalarwtWebioEA24oemClockDay | read-write | mandatory | Date: Day of the month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.2.3.4 | ScalarwtWebioEA24oemClockMonth | read-write | mandatory | Date: Month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.2.3.5 | ScalarwtWebioEA24oemClockYear | read-write | mandatory | Date: Year, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3 | NodewtWebioEA24oemBasic | |||
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.1 | NodewtWebioEA24oemNetwork | |||
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.1.1 | ScalarwtWebioEA24oemIpAddress | read-write | mandatory | IP address of the Webio |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.1.2 | ScalarwtWebioEA24oemSubnetMask | read-write | mandatory | Subnet mask of the Webio |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.1.3 | ScalarwtWebioEA24oemGateway | read-write | mandatory | Gateway of the Webio |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.1.4 | ScalarwtWebioEA24oemDnsServer1 | read-write | mandatory | IP address of the 1st DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.1.5 | ScalarwtWebioEA24oemDnsServer2 | read-write | mandatory | IP address of the 2nd DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.1.6 | ScalarwtWebioEA24oemAddConfig | read-write | mandatory | Additional configuration (1=ON): Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1: DHCP enable Bit 0: BOOTP enable |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.2 | NodewtWebioEA24oemHTTP | |||
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.2.1 | ScalarwtWebioEA24oemStartup | read-write | mandatory | Binary coded start page, more than one page must not be selected: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 2: user.htm Bit 1: home.htm Bit … |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.2.2 | ScalarwtWebioEA24oemGetHeaderEnable | read-write | mandatory | If bits are set, every answer of a short form GET question will be lead by the IP-address and name of the device (Header) or a HTTP header (HTTP): Octet 1: unu… |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.2.3 | ScalarwtWebioEA24oemHttpInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.2.4 | ScalarwtWebioEA24oemHttpPort | read-write | mandatory | Definition of the standard HTML port (Default: 80). |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.3 | NodewtWebioEA24oemMail | |||
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.3.1 | ScalarwtWebioEA24oemMailAdName | read-write | mandatory | Device name for mail administration. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.3.2 | ScalarwtWebioEA24oemMailReply | read-write | mandatory | Reply address for the mail server. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.3.3 | ScalarwtWebioEA24oemMailServer | read-write | mandatory | Name or IP address of the mail server. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.3.4 | ScalarwtWebioEA24oemMailEnable | read-write | mandatory | Set this bit to enable the sending of mails: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Mail enable |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.3.5 | ScalarwtWebioEA24oemMailAuthentication | read-write | mandatory | Selection of the authentication modi: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTE… |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.3.6 | ScalarwtWebioEA24oemMailAuthUser | read-write | mandatory | Name of the user to be authenticated. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.3.7 | ScalarwtWebioEA24oemMailAuthPassword | read-write | mandatory | Authentication password. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.3.8 | ScalarwtWebioEA24oemMailPop3Server | read-write | mandatory | Name or Ip-address of the POP3 Servers. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.4 | NodewtWebioEA24oemSNMP | |||
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.4.1 | ScalarwtWebioEA24oemSnmpEnable | read-write | mandatory | Set bit 0 to enable SNMP. If disabled, the device did not respond to any SNMP requests. Bit 1 decided wether the community string of read operations is compare… |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.4.2 | ScalarwtWebioEA24oemSnmpCommunityStringRead | read-write | mandatory | Community string read only |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.4.3 | ScalarwtWebioEA24oemSnmpCommunityStringReadWrite | read-write | mandatory | Community string read / write |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.4.4 | ScalarwtWebioEA24oemSnmpSystemTrapManagerIP | read-write | mandatory | Name or IP address of the TCP server which accepts the system trap. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.4.5 | ScalarwtWebioEA24oemSnmpSystemTrapEnable | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2-7: unused |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.5 | NodewtWebioEA24oemUDP | |||
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.5.1 | ScalarwtWebioEA24oemUdpAdminPort | read-write | mandatory | Udp port to which the Udp queries ( short form GET requests) can be sent. This port number must be unique within the device. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.5.2 | ScalarwtWebioEA24oemUdpEnable | read-write | mandatory | Set this bit to enable UDP support: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : UDP enable |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.5.3 | ScalarwtWebioEA24oemUdpRemotePort | read-write | mandatory | Udp remote port setting. If this value is set to zero, the source port read from a request will be used as destination port for the answer. A non zero value fo… |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.6 | NodewtWebioEA24oemBinary | |||
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.6.1 | ScalarwtWebioEA24oemBinaryModeCount | read-only | mandatory | Number of independent binary channels. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.6.2 | TablewtWebioEA24oemBinaryIfTable | not-accessible | mandatory | Table of indices. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.6.2.1 | RowwtWebioEA24oemBinaryIfEntry | not-accessible | mandatory | Indices of the binary channels. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.6.2.1.1 | ColumnwtWebioEA24oemBinaryModeNo | read-only | mandatory | Number of the binary channel. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.6.3 | TablewtWebioEA24oemBinaryTable | not-accessible | mandatory | Table of properties of the binary mode. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.6.3.1 | RowwtWebioEA24oemBinaryEntry | not-accessible | mandatory | Binary properties. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.6.3.1.1 | ColumnwtWebioEA24oemBinaryOperationMode | read-write | mandatory | Selection of the operation mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: … |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.6.3.1.2 | ColumnwtWebioEA24oemBinaryTcpServerLocalPort | read-write | mandatory | Local TCP port for data exchange in this server mode. This port number must be unique within the device. Reserved port number must not be used (refere to the m… |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.6.3.1.3 | ColumnwtWebioEA24oemBinaryTcpServerInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.6.3.1.4 | ColumnwtWebioEA24oemBinaryTcpServerApplicationMode | read-write | mandatory | Selection of the application mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4… |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.6.3.1.5 | ColumnwtWebioEA24oemBinaryTcpClientLocalPort | read-write | mandatory | Local TCP port for data exchange in this client mode. This port number must be unique within the device. Reserved port number must not be used (refere to the m… |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.6.3.1.6 | ColumnwtWebioEA24oemBinaryTcpClientServerPort | read-write | mandatory | Port number of the server. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when setting t… |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.6.3.1.7 | ColumnwtWebioEA24oemBinaryTcpClientServerIpAddr | read-write | mandatory | Ip address of the server. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when setting th… |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.6.3.1.8 | ColumnwtWebioEA24oemBinaryTcpClientServerPassword | read-write | mandatory | Building a connection may be protected by the administrator password of the server. Enter the server password to establish the connection, if a server administ… |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.6.3.1.9 | ColumnwtWebioEA24oemBinaryTcpClientInactivity | read-write | mandatory | Connection timeout in 100ms. If no data are exchanged within the specified time, the device closes the connection to the server. The value 0 deactivates the ti… |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.6.3.1.10 | ColumnwtWebioEA24oemBinaryTcpClientInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.6.3.1.11 | ColumnwtWebioEA24oemBinaryTcpClientInterval | read-write | mandatory | Configurable interval with a 100ms base, in which the Webio device sends data to the configured application. A interval of zero stopps the periodical sending. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.6.3.1.12 | ColumnwtWebioEA24oemBinaryTcpClientApplicationMode | read-write | mandatory | Selection of the application mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4… |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.6.3.1.13 | ColumnwtWebioEA24oemBinaryUdpPeerLocalPort | read-write | mandatory | Local UDP port for data exchange in this peer to peer mode. This port number must be unique within the device. Reserved port number must not be used (refere to… |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.6.3.1.14 | ColumnwtWebioEA24oemBinaryUdpPeerRemotePort | read-write | mandatory | Port number of the remote device. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when se… |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.6.3.1.15 | ColumnwtWebioEA24oemBinaryUdpPeerRemoteIpAddr | read-write | mandatory | Ip address of the remote device. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when set… |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.6.3.1.16 | ColumnwtWebioEA24oemBinaryUdpPeerInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.6.3.1.17 | ColumnwtWebioEA24oemBinaryUdpPeerInterval | read-write | mandatory | Configurable interval with a 100ms base, in which the Webio device sends data to the configured remote device. A interval of zero stopps the periodical sending. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.6.3.1.18 | ColumnwtWebioEA24oemBinaryUdpPeerApplicationMode | read-write | mandatory | Selection of the application mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4… |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.6.3.1.19 | ColumnwtWebioEA24oemBinaryConnectedPort | read-only | mandatory | Port number of the remote device, after connection has been established. In case of no connection or missing port informations a zero will be read. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.6.3.1.20 | ColumnwtWebioEA24oemBinaryConnectedIpAddr | read-only | mandatory | IP address of the remote device, after connection has been established. In case of no connection or missing port informations 0.0.0.0 will be read. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.6.3.1.21 | ColumnwtWebioEA24oemBinaryTcpServerClientHttpPort | read-write | mandatory | HTTP port number of the remote device at TCP Server Mode. If an mailfunction occurs status informations will be send to this port. Not used at mode Compatible … |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.6.3.1.22 | ColumnwtWebioEA24oemBinaryTcpClientServerHttpPort | read-write | mandatory | HTTP port number of the remote device at TCP Client Mode. In the operating mode Box2Box connection status informations will be exchanged through this port. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.7 | NodewtWebioEA24oemSyslog | |||
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.7.1 | ScalarwtWebioEA24oemSyslogServerIP | read-write | mandatory | Name or IP address of the Syslog server, which accepts the Syslog messgaes. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.7.2 | ScalarwtWebioEA24oemSyslogServerPort | read-write | mandatory | Portnumber of the Syslog servers, default 514. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.7.3 | ScalarwtWebioEA24oemSyslogSystemMessagesEnable | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2: Diag Messages Bit 3-7: unused |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.7.4 | ScalarwtWebioEA24oemSyslogEnable | read-write | mandatory | Set bit 0to enable Syslog: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Syslog enable |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.8 | NodewtWebioEA24oemFTP | |||
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.8.1 | ScalarwtWebioEA24oemFTPServerIP | read-write | mandatory | Name or IP address of the FTP server, which accepts the FTP messages. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.8.2 | ScalarwtWebioEA24oemFTPServerControlPort | read-write | mandatory | Portnumber of the control port of the FTP server, default 21. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.8.3 | ScalarwtWebioEA24oemFTPUserName | read-write | mandatory | FTP Loggin: user name. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.8.4 | ScalarwtWebioEA24oemFTPPassword | read-write | mandatory | FTP Loggin: user password. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.8.5 | ScalarwtWebioEA24oemFTPAccount | read-write | mandatory | FTP Loggin: name of account. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.8.6 | ScalarwtWebioEA24oemFTPOption | read-write | mandatory | Bit 0 switches the FTP Server in Passiv-Mode, the Client controls the data connection on its own: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit … |
| 1.3.6.1.4.1.5040.1.2.14.3.1.3.8.7 | ScalarwtWebioEA24oemFTPEnable | read-write | mandatory | Set Bit 0 to enable FTP: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : FTP enable |
| 1.3.6.1.4.1.5040.1.2.14.3.1.4 | NodewtWebioEA24oemOutputMode | |||
| 1.3.6.1.4.1.5040.1.2.14.3.1.4.1 | TablewtWebioEA24oemOutputModeTable | not-accessible | mandatory | Table of output mode configurations dependent on the output indices. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.4.1.1 | RowwtWebioEA24oemOutputModeEntry | not-accessible | mandatory | Output mode configurations of the individual outputs. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.4.1.1.1 | ColumnwtWebioEA24oemOutputModeBit | read-write | mandatory | This binary coded output mode defines the individual operation mode for any output. More than one mode must not be selected. The OCTETS are interpreted bit-by-… |
| 1.3.6.1.4.1.5040.1.2.14.3.1.4.2 | ScalarwtWebioEA24oemSafetyTimeout | read-write | mandatory | After this period of time (multiple of 100ms) without receiving data outputs switch to their Safety States. For each output a independend safety state could be… |
| 1.3.6.1.4.1.5040.1.2.14.3.1.4.3 | ScalarwtWebioEA24oemLoadControlEnable | read-write | mandatory | Here the function of automatic load control can be enabled. All output were tested in pairs (0-1, 2-3, 4-5, 6-7, 8-9, 10-11). If an error occours at one output… |
| 1.3.6.1.4.1.5040.1.2.14.3.1.5 | NodewtWebioEA24oemAlarm | |||
| 1.3.6.1.4.1.5040.1.2.14.3.1.5.1 | ScalarwtWebioEA24oemAlarmCount | read-only | mandatory | Number of independent alarms. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.5.2 | TablewtWebioEA24oemAlarmIfTable | not-accessible | mandatory | List of alarm indices. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.5.2.1 | RowwtWebioEA24oemAlarmIfEntry | not-accessible | mandatory | Numbers of the alarms. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.5.2.1.1 | ColumnwtWebioEA24oemAlarmNo | read-only | mandatory | Numbers of the alarms. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.5.3 | TablewtWebioEA24oemAlarmTable | not-accessible | mandatory | List of settings depending on the alarm number. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.5.3.1 | RowwtWebioEA24oemAlarmEntry | not-accessible | mandatory | Alarm parameters of the individual alarms. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.5.3.1.1 | ColumnwtWebioEA24oemAlarmInputTrigger | read-write | mandatory | This variable allows setting of individual input trigger conditions. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an input. Bit 0 corr… |
| 1.3.6.1.4.1.5040.1.2.14.3.1.5.3.1.2 | ColumnwtWebioEA24oemAlarmOutputTrigger | read-write | mandatory | This variable allows setting of individual output trigger conditions. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 co… |
| 1.3.6.1.4.1.5040.1.2.14.3.1.5.3.1.3 | ColumnwtWebioEA24oemAlarmSystemTrigger | read-write | mandatory | Binary coded trigger conditions: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, … |
| 1.3.6.1.4.1.5040.1.2.14.3.1.5.3.1.4 | ColumnwtWebioEA24oemAlarmMaxCounterValue | read-write | mandatory | This variable configures a max. counter value. If an input counter value exceeds this max. value, the corresponding alarm is triggered. Input counters with its… |
| 1.3.6.1.4.1.5040.1.2.14.3.1.5.3.1.5 | ColumnwtWebioEA24oemAlarmInterval | read-write | mandatory | Send interval for alarm messages. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.5.3.1.6 | ColumnwtWebioEA24oemAlarmEnable | read-write | mandatory | Binary coded alarm enable: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Mail Enable Bit 1: SNMP Trap enable Bit 2: UDP enable Bit 3: Send in… |
| 1.3.6.1.4.1.5040.1.2.14.3.1.5.3.1.7 | ColumnwtWebioEA24oemAlarmMailAddr | read-write | mandatory | E-Mail address for sending the alarm mail to. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.5.3.1.8 | ColumnwtWebioEA24oemAlarmMailSubject | read-write | mandatory | Subject line for alarm mail. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.5.3.1.9 | ColumnwtWebioEA24oemAlarmMailText | read-write | mandatory | Alarm mail text: States of the Webio device can be included by using special tags. Please refer to the respective Webio manual |
| 1.3.6.1.4.1.5040.1.2.14.3.1.5.3.1.10 | ColumnwtWebioEA24oemAlarmSnmpManagerIP | read-write | mandatory | IP address of the SNMP Manager to which the Webio device should send SNMP traps. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.5.3.1.11 | ColumnwtWebioEA24oemAlarmSnmpTrapText | read-write | mandatory | This text appears in the trap body. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.5.3.1.12 | ColumnwtWebioEA24oemAlarmUdpIpAddr | read-write | mandatory | IP address of the UDP listener to which the Webio device should send UDP traps. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.5.3.1.13 | ColumnwtWebioEA24oemAlarmUdpPort | read-write | mandatory | Port number of the UDP listener to which the Webio device should send UDP traps. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.5.3.1.14 | ColumnwtWebioEA24oemAlarmUdpText | read-write | mandatory | This text appears in the UDP trap body. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.5.3.1.15 | ColumnwtWebioEA24oemAlarmTcpIpAddr | read-write | mandatory | IP address of the TCP listener to which the Webio device should send TCP traps. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.5.3.1.16 | ColumnwtWebioEA24oemAlarmTcpPort | read-write | mandatory | Port number of the TCP listener to which the Webio device should send TCP traps. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.5.3.1.17 | ColumnwtWebioEA24oemAlarmTcpText | read-write | mandatory | This text appears in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.5.3.1.18 | ColumnwtWebioEA24oemAlarmSyslogIpAddr | read-write | mandatory | IP address of the syslog server to which the Webio device should send syslog messages. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.5.3.1.19 | ColumnwtWebioEA24oemAlarmSyslogPort | read-write | mandatory | Port number of the syslog server to which the Webio device should send syslog messages. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.5.3.1.20 | ColumnwtWebioEA24oemAlarmSyslogText | read-write | mandatory | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.5.3.1.21 | ColumnwtWebioEA24oemAlarmFtpDataPort | read-write | mandatory | Local data port: 1..65535 or AUTO: the next free port will be assigned. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.5.3.1.22 | ColumnwtWebioEA24oemAlarmFtpFileName | read-write | mandatory | Name of the file including path informations. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.5.3.1.23 | ColumnwtWebioEA24oemAlarmFtpText | read-write | mandatory | Message text to store on the FTP server. |
| 1.3.6.1.4.1.5040.1.2.14.3.1.5.3.1.24 | ColumnwtWebioEA24oemAlarmFtpOption | read-write | mandatory | Binary coded options, select only one option at the same time: STORE = replace file APPEND = append message at the end of the file Octet 1: unused Octet 2: unu… |
| 1.3.6.1.4.1.5040.1.2.14.3.1.5.3.1.25 | ColumnwtWebioEA24oemAlarmTimerCron | read-write | mandatory | This entry contains 5 space or tab seperated text fields for time trigger definition. Each field must match with the actual time to trigger a message, weekday … |
| 1.3.6.1.4.1.5040.1.2.14.3.1.5.4 | ScalarwtWebioEA24oemLoadControlView | read-only | mandatory | Here the result of automatic load control can be read. All output were tested in pairs (0-1, 2-3, 4-5, 6-7, 8-9, 10-11). If an error occours at one output, bot… |
| 1.3.6.1.4.1.5040.1.2.14.3.1.5.5 | ScalarwtWebioEA24oemLCShutDownView | read-write | mandatory | Here the result of the automatic load control shut down can be read. All outputs remain switched of, until a zero is written into this variable. But previously… |
| 1.3.6.1.4.1.5040.1.2.14.3.2 | NodewtWebioEA24oemPorts | |||
| 1.3.6.1.4.1.5040.1.2.14.3.2.1 | TablewtWebioEA24oemInputPortTable | not-accessible | mandatory | List of settings depending on the input number. |
| 1.3.6.1.4.1.5040.1.2.14.3.2.1.1 | RowwtWebioEA24oemInputPortEntry | not-accessible | mandatory | Input parameter for the individual inputs. |
| 1.3.6.1.4.1.5040.1.2.14.3.2.1.1.1 | ColumnwtWebioEA24oemPortInputName | read-write | mandatory | Name of the input. |
| 1.3.6.1.4.1.5040.1.2.14.3.2.1.1.2 | ColumnwtWebioEA24oemPortInputText | read-write | mandatory | Description of the input. |
| 1.3.6.1.4.1.5040.1.2.14.3.2.1.1.3 | ColumnwtWebioEA24oemPortInputMode | read-write | mandatory | Binary coded modes: Selecting short pulse detection enable by setting the corresponding bit to 1 enables interrupt support for counting. Only positive edges ar… |
| 1.3.6.1.4.1.5040.1.2.14.3.2.1.1.4 | ColumnwtWebioEA24oemPortInputFilter | read-write | mandatory | Pulses with a duration shorter than here specified (duration in 1/1000 sec), are ignored. |
| 1.3.6.1.4.1.5040.1.2.14.3.2.2 | TablewtWebioEA24oemOutputPortTable | not-accessible | mandatory | List of settings depending on the output number. |
| 1.3.6.1.4.1.5040.1.2.14.3.2.2.1 | RowwtWebioEA24oemOutputPortEntry | not-accessible | mandatory | Output parameters of the individual outputs. |
| 1.3.6.1.4.1.5040.1.2.14.3.2.2.1.1 | ColumnwtWebioEA24oemPortOutputName | read-write | mandatory | Name of the output. |
| 1.3.6.1.4.1.5040.1.2.14.3.2.2.1.2 | ColumnwtWebioEA24oemPortOutputText | read-write | mandatory | Description of the output. |
| 1.3.6.1.4.1.5040.1.2.14.3.2.2.1.3 | ColumnwtWebioEA24oemPortOutputGroupMode | read-write | mandatory | It is possible to connect outputs together to increase the output current. This could be done by connecting 2 or 4 outputs in a group together. All bits of suc… |
| 1.3.6.1.4.1.5040.1.2.14.3.2.2.1.4 | ColumnwtWebioEA24oemPortOutputSafetyState | read-write | mandatory | This variable allows setting of individual digital outputs. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds … |
| 1.3.6.1.4.1.5040.1.2.14.3.2.2.1.5 | ColumnwtWebioEA24oemPortLogicInputMask | read-write | mandatory | Selecting one of these inputs by setting the corresponding bit to 1 enables the logic function for the output identified by the index within this table. The ca… |
| 1.3.6.1.4.1.5040.1.2.14.3.2.2.1.6 | ColumnwtWebioEA24oemPortLogicInputInverter | read-write | mandatory | Every input bit selected here will be inverted. OCTET 1: unused OCTET 2: Bit 0-7 : inputs 16 - 23 OCTET 3: Bit 0-7 : inputs 8 - 15 OCTET 4: Bit 0-7 : inputs 0 … |
| 1.3.6.1.4.1.5040.1.2.14.3.2.2.1.7 | ColumnwtWebioEA24oemPortLogicFunction | read-write | mandatory | This determines the logic function. No more than one function may be selected. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 0 : logic function … |
| 1.3.6.1.4.1.5040.1.2.14.3.2.2.1.8 | ColumnwtWebioEA24oemPortLogicOutputInverter | read-write | mandatory | The logical operation result could be inverteted by setting the corresponding bit to 1. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 0 : Output… |
| 1.3.6.1.4.1.5040.1.2.14.3.2.2.1.9 | ColumnwtWebioEA24oemPortPulseDuration | read-write | mandatory | Pulse length in 1/1000 sec. Setting this value to zero, disables the pulse output. |
| 1.3.6.1.4.1.5040.1.2.14.3.2.2.1.10 | ColumnwtWebioEA24oemPortPulsePolarity | read-write | mandatory | This value defines the polarity of the output pulse, if wtWebioEA24oemPortPulseDuration is not set to zero. After the pulse is finished, the output switches ba… |
| 1.3.6.1.4.1.5040.1.2.14.3.3 | NodewtWebioEA24oemManufact | |||
| 1.3.6.1.4.1.5040.1.2.14.3.3.1 | ScalarwtWebioEA24oemMfName | read-write | mandatory | Manufacturer company name |
| 1.3.6.1.4.1.5040.1.2.14.3.3.2 | ScalarwtWebioEA24oemMfAddr | read-write | mandatory | Manufacturer address. |
| 1.3.6.1.4.1.5040.1.2.14.3.3.3 | ScalarwtWebioEA24oemMfHotline | read-write | mandatory | Manufacturer hotline. |
| 1.3.6.1.4.1.5040.1.2.14.3.3.4 | ScalarwtWebioEA24oemMfInternet | read-write | mandatory | Manufacturer Internet address. |
| 1.3.6.1.4.1.5040.1.2.14.3.3.5 | ScalarwtWebioEA24oemMfDeviceTyp | read-write | mandatory | Manufacturer device name (model number). |
| 1.3.6.1.4.1.5040.1.2.14.4 | NodewtWebioEA24oemDiag | |||
| 1.3.6.1.4.1.5040.1.2.14.4.1 | ScalarwtWebioEA24oemDiagErrorCount | read-only | mandatory | Number of entries in the error memory. |
| 1.3.6.1.4.1.5040.1.2.14.4.2 | ScalarwtWebioEA24oemDiagBinaryError | read-only | mandatory | Error causes coded bit-by-bit. |
| 1.3.6.1.4.1.5040.1.2.14.4.3 | ScalarwtWebioEA24oemDiagErrorIndex | read-write | mandatory | The value of this variable is used as an index to read an error massege from wtWebioEA24oemDiagErrorMessage. Errors are numbered from 1 to wtWebioEA24oemDiagEr… |
| 1.3.6.1.4.1.5040.1.2.14.4.4 | ScalarwtWebioEA24oemDiagErrorMessage | read-only | mandatory | Using wtWebioEA24oemDiagErrorIndex as an index, the appropriate message is available. |
| 1.3.6.1.4.1.5040.1.2.14.4.5 | ScalarwtWebioEA24oemDiagErrorClear | write-only | mandatory | Writing 1 into this variable clears all diagnosis messages. |
| 1.3.6.1.4.1.5040.1.2.14.53 | NodewtWebioEA24oemAlert1 | This SNMP trap is generated when Alarm 1 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.14.54 | NodewtWebioEA24oemAlert2 | This SNMP trap is generated when Alarm 2 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.14.55 | NodewtWebioEA24oemAlert3 | This SNMP trap is generated when Alarm 3 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.14.56 | NodewtWebioEA24oemAlert4 | This SNMP trap is generated when Alarm 4 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.14.57 | NodewtWebioEA24oemAlert5 | This SNMP trap is generated when Alarm 5 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.14.58 | NodewtWebioEA24oemAlert6 | This SNMP trap is generated when Alarm 6 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.14.59 | NodewtWebioEA24oemAlert7 | This SNMP trap is generated when Alarm 7 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.14.60 | NodewtWebioEA24oemAlert8 | This SNMP trap is generated when Alarm 8 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.14.61 | NodewtWebioEA24oemAlert9 | This SNMP trap is generated when Alarm 9 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.14.62 | NodewtWebioEA24oemAlert10 | This SNMP trap is generated when Alarm 10 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.14.63 | NodewtWebioEA24oemAlert11 | This SNMP trap is generated when Alarm 11 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.14.64 | NodewtWebioEA24oemAlert12 | This SNMP trap is generated when Alarm 12 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.14.65 | NodewtWebioEA24oemAlert13 | This SNMP trap is generated when Alarm 13 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.14.66 | NodewtWebioEA24oemAlert14 | This SNMP trap is generated when Alarm 14 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.14.67 | NodewtWebioEA24oemAlert15 | This SNMP trap is generated when Alarm 15 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.14.68 | NodewtWebioEA24oemAlert16 | This SNMP trap is generated when Alarm 16 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.14.71 | NodewtWebioEA24oemAlert17 | This SNMP trap is generated when Alarm 1 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.14.72 | NodewtWebioEA24oemAlert18 | This SNMP trap is generated when Alarm 2 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.14.73 | NodewtWebioEA24oemAlert19 | This SNMP trap is generated when Alarm 3 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.14.74 | NodewtWebioEA24oemAlert20 | This SNMP trap is generated when Alarm 4 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.14.75 | NodewtWebioEA24oemAlert21 | This SNMP trap is generated when Alarm 5 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.14.76 | NodewtWebioEA24oemAlert22 | This SNMP trap is generated when Alarm 6 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.14.77 | NodewtWebioEA24oemAlert23 | This SNMP trap is generated when Alarm 7 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.14.78 | NodewtWebioEA24oemAlert24 | This SNMP trap is generated when Alarm 8 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.14.79 | NodewtWebioEA24oemAlert25 | This SNMP trap is generated when Alarm 9 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.14.80 | NodewtWebioEA24oemAlert26 | This SNMP trap is generated when Alarm 10 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.14.81 | NodewtWebioEA24oemAlert27 | This SNMP trap is generated when Alarm 11 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.14.82 | NodewtWebioEA24oemAlert28 | This SNMP trap is generated when Alarm 12 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.14.83 | NodewtWebioEA24oemAlert29 | This SNMP trap is generated when Alarm 13 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.14.84 | NodewtWebioEA24oemAlert30 | This SNMP trap is generated when Alarm 14 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.14.85 | NodewtWebioEA24oemAlert31 | This SNMP trap is generated when Alarm 15 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.14.86 | NodewtWebioEA24oemAlert32 | This SNMP trap is generated when Alarm 16 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.14.110 | NodewtWebioEA24oemAlertDiag | This SNMP trap is generated when a diag/error message was generated, the SNMP-Trap-Enable bit is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.19 | NodewtWebioEA12x6Rel | |||
| 1.3.6.1.4.1.5040.1.2.19.1 | NodewtWebioEA12x6RelInOut | |||
| 1.3.6.1.4.1.5040.1.2.19.1.1 | ScalarwtWebioEA12x6RelInputs | read-only | mandatory | Number of idependent inputs. |
| 1.3.6.1.4.1.5040.1.2.19.1.2 | ScalarwtWebioEA12x6RelOutputs | read-only | mandatory | Number of independent outputs. |
| 1.3.6.1.4.1.5040.1.2.19.1.3 | TablewtWebioEA12x6RelInputTable | not-accessible | mandatory | List of input indices. |
| 1.3.6.1.4.1.5040.1.2.19.1.3.1 | RowwtWebioEA12x6RelInputEntry | not-accessible | mandatory | Number of the inputs. |
| 1.3.6.1.4.1.5040.1.2.19.1.3.1.1 | ColumnwtWebioEA12x6RelInputNo | read-only | mandatory | Index numbers of the inputs. |
| 1.3.6.1.4.1.5040.1.2.19.1.3.1.2 | ColumnwtWebioEA12x6RelInputCounter | read-only | mandatory | Value of the input counter. |
| 1.3.6.1.4.1.5040.1.2.19.1.3.1.3 | ColumnwtWebioEA12x6RelInputCounterClear | read-only | mandatory | Clears the input counter after returning its value. |
| 1.3.6.1.4.1.5040.1.2.19.1.4 | ScalarwtWebioEA12x6RelInputValue | read-only | mandatory | This variable is used to read the inputs of the digital I/O port. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an input. Bit 0 corresp… |
| 1.3.6.1.4.1.5040.1.2.19.1.5 | TablewtWebioEA12x6RelOutputTable | not-accessible | mandatory | List of output indices. |
| 1.3.6.1.4.1.5040.1.2.19.1.5.1 | RowwtWebioEA12x6RelOutputEntry | not-accessible | mandatory | Number of the outputs. |
| 1.3.6.1.4.1.5040.1.2.19.1.5.1.1 | ColumnwtWebioEA12x6RelOutputNo | read-only | mandatory | Output number. |
| 1.3.6.1.4.1.5040.1.2.19.1.5.1.2 | ColumnwtWebioEA12x6RelOutputState | read-write | mandatory | Setting and reading of the states of the outputs, 0-OFF, 1-ON. |
| 1.3.6.1.4.1.5040.1.2.19.1.6 | ScalarwtWebioEA12x6RelOutputValue | read-write | mandatory | This variable is used to read and write the outputs of the digital I/O port. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. B… |
| 1.3.6.1.4.1.5040.1.2.19.1.7 | ScalarwtWebioEA12x6RelSetOutput | read-write | mandatory | This variable allows setting of individual digital outputs. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds … |
| 1.3.6.1.4.1.5040.1.2.19.2 | NodewtWebioEA12x6RelSessCntrl | |||
| 1.3.6.1.4.1.5040.1.2.19.2.1 | ScalarwtWebioEA12x6RelSessCntrlPassword | read-write | mandatory | Entering this password opens a session which is ended by writing a 1 to wtWebioEA12x6RelSessCntrlLogout. When read this variable provides a string of length ze… |
| 1.3.6.1.4.1.5040.1.2.19.2.2 | ScalarwtWebioEA12x6RelSessCntrlConfigMode | read-only | mandatory | When the device is in SNMP configuration mode, the value 1 is returned, otherwise 0. If the read value is 0 even though the password was written, the device is… |
| 1.3.6.1.4.1.5040.1.2.19.2.3 | ScalarwtWebioEA12x6RelSessCntrlLogout | read-write | mandatory | If the device is in configuration mode and the session was opened by this SNMP Manager, writing a 1 to this variable will end the session and all parameters ar… |
| 1.3.6.1.4.1.5040.1.2.19.2.4 | ScalarwtWebioEA12x6RelSessCntrlAdminPassword | read-write | mandatory | This password protects access to the variables with administrator rights. It can only be changed by the administrator. If no password was assigned, the valid p… |
| 1.3.6.1.4.1.5040.1.2.19.2.5 | ScalarwtWebioEA12x6RelSessCntrlConfigPassword | read-write | mandatory | This password protects access to the variables with configurator rights. It can be changed by the administrator and by the configurator. If no password was ass… |
| 1.3.6.1.4.1.5040.1.2.19.3 | NodewtWebioEA12x6RelConfig | |||
| 1.3.6.1.4.1.5040.1.2.19.3.1 | NodewtWebioEA12x6RelDevice | |||
| 1.3.6.1.4.1.5040.1.2.19.3.1.1 | NodewtWebioEA12x6RelText | |||
| 1.3.6.1.4.1.5040.1.2.19.3.1.1.1 | ScalarwtWebioEA12x6RelDeviceName | read-write | mandatory | Name of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.1.2 | ScalarwtWebioEA12x6RelDeviceText | read-write | mandatory | Description of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.1.3 | ScalarwtWebioEA12x6RelDeviceLocation | read-write | mandatory | Description of the location of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.1.4 | ScalarwtWebioEA12x6RelDeviceContact | read-write | mandatory | Contact address of the system operator of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.2 | NodewtWebioEA12x6RelTimeDate | |||
| 1.3.6.1.4.1.5040.1.2.19.3.1.2.1 | NodewtWebioEA12x6RelTimeZone | |||
| 1.3.6.1.4.1.5040.1.2.19.3.1.2.1.1 | ScalarwtWebioEA12x6RelTzOffsetHrs | read-write | mandatory | Offset hours for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.2.1.2 | ScalarwtWebioEA12x6RelTzOffsetMin | read-write | mandatory | Offset minutes for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.2.1.3 | ScalarwtWebioEA12x6RelTzEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Timezone |
| 1.3.6.1.4.1.5040.1.2.19.3.1.2.1.4 | ScalarwtWebioEA12x6RelStTzOffsetHrs | read-write | mandatory | Offset hours of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.2.1.5 | ScalarwtWebioEA12x6RelStTzOffsetMin | read-write | mandatory | Offset minutes of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.2.1.6 | ScalarwtWebioEA12x6RelStTzEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Summertime |
| 1.3.6.1.4.1.5040.1.2.19.3.1.2.1.7 | ScalarwtWebioEA12x6RelStTzStartMonth | read-write | mandatory | Month in which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.2.1.8 | ScalarwtWebioEA12x6RelStTzStartMode | read-write | mandatory | Mode of the day of the week for which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.2.1.9 | ScalarwtWebioEA12x6RelStTzStartWday | read-write | mandatory | Day of the week on which the change is made from winter time to summer time |
| 1.3.6.1.4.1.5040.1.2.19.3.1.2.1.10 | ScalarwtWebioEA12x6RelStTzStartHrs | read-write | mandatory | Hour in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.2.1.11 | ScalarwtWebioEA12x6RelStTzStartMin | read-write | mandatory | Minute in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.2.1.12 | ScalarwtWebioEA12x6RelStTzStopMonth | read-write | mandatory | Month in which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.2.1.13 | ScalarwtWebioEA12x6RelStTzStopMode | read-write | mandatory | Mode of the week day on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.2.1.14 | ScalarwtWebioEA12x6RelStTzStopWday | read-write | mandatory | Day of the week on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.2.1.15 | ScalarwtWebioEA12x6RelStTzStopHrs | read-write | mandatory | Hour at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.2.1.16 | ScalarwtWebioEA12x6RelStTzStopMin | read-write | mandatory | Minute at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.2.2 | NodewtWebioEA12x6RelTimeServer | |||
| 1.3.6.1.4.1.5040.1.2.19.3.1.2.2.1 | ScalarwtWebioEA12x6RelTimeServer1 | read-write | mandatory | IP address or name of the 1st time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.19.3.1.2.2.2 | ScalarwtWebioEA12x6RelTimeServer2 | read-write | mandatory | IP address or name of the 2nd time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.19.3.1.2.2.3 | ScalarwtWebioEA12x6RelTsEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Time Server |
| 1.3.6.1.4.1.5040.1.2.19.3.1.2.2.4 | ScalarwtWebioEA12x6RelTsSyncTime | read-write | mandatory | Daily synchronisation time with the time server (hour: 0-23). |
| 1.3.6.1.4.1.5040.1.2.19.3.1.2.3 | NodewtWebioEA12x6RelDeviceClock | |||
| 1.3.6.1.4.1.5040.1.2.19.3.1.2.3.1 | ScalarwtWebioEA12x6RelClockHrs | read-write | mandatory | Clock hours taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.2.3.2 | ScalarwtWebioEA12x6RelClockMin | read-write | mandatory | Clock minutes taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.2.3.3 | ScalarwtWebioEA12x6RelClockDay | read-write | mandatory | Date: Day of the month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.2.3.4 | ScalarwtWebioEA12x6RelClockMonth | read-write | mandatory | Date: Month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.2.3.5 | ScalarwtWebioEA12x6RelClockYear | read-write | mandatory | Date: Year, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3 | NodewtWebioEA12x6RelBasic | |||
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.1 | NodewtWebioEA12x6RelNetwork | |||
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.1.1 | ScalarwtWebioEA12x6RelIpAddress | read-write | mandatory | IP address of the Webio |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.1.2 | ScalarwtWebioEA12x6RelSubnetMask | read-write | mandatory | Subnet mask of the Webio |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.1.3 | ScalarwtWebioEA12x6RelGateway | read-write | mandatory | Gateway of the Webio |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.1.4 | ScalarwtWebioEA12x6RelDnsServer1 | read-write | mandatory | IP address of the 1st DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.1.5 | ScalarwtWebioEA12x6RelDnsServer2 | read-write | mandatory | IP address of the 2nd DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.1.6 | ScalarwtWebioEA12x6RelAddConfig | read-write | mandatory | Additional configuration (1=ON): Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1: DHCP enable Bit 0: BOOTP enable |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.2 | NodewtWebioEA12x6RelHTTP | |||
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.2.1 | ScalarwtWebioEA12x6RelStartup | read-write | mandatory | Binary coded start page, more than one page must not be selected: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 2: user.htm Bit 1: home.htm Bit … |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.2.2 | ScalarwtWebioEA12x6RelGetHeaderEnable | read-write | mandatory | If bits are set, every answer of a short form GET question will be lead by the IP-address and name of the device (Header) or a HTTP header (HTTP): Octet 1: unu… |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.2.3 | ScalarwtWebioEA12x6RelHttpInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.2.4 | ScalarwtWebioEA12x6RelHttpPort | read-write | mandatory | Definition of the standard HTML port (Default: 80). |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.3 | NodewtWebioEA12x6RelMail | |||
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.3.1 | ScalarwtWebioEA12x6RelMailAdName | read-write | mandatory | Device name for mail administration. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.3.2 | ScalarwtWebioEA12x6RelMailReply | read-write | mandatory | Reply address for the mail server. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.3.3 | ScalarwtWebioEA12x6RelMailServer | read-write | mandatory | Name or IP address of the mail server. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.3.4 | ScalarwtWebioEA12x6RelMailEnable | read-write | mandatory | Set this bit to enable the sending of mails: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Mail enable |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.3.5 | ScalarwtWebioEA12x6RelMailAuthentication | read-write | mandatory | Selection of the authentication modi: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTE… |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.3.6 | ScalarwtWebioEA12x6RelMailAuthUser | read-write | mandatory | Name of the user to be authenticated. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.3.7 | ScalarwtWebioEA12x6RelMailAuthPassword | read-write | mandatory | Authentication password. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.3.8 | ScalarwtWebioEA12x6RelMailPop3Server | read-write | mandatory | Name or Ip-address of the POP3 Servers. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.4 | NodewtWebioEA12x6RelSNMP | |||
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.4.1 | ScalarwtWebioEA12x6RelSnmpEnable | read-write | mandatory | Set bit 0 to enable SNMP. If disabled, the device did not respond to any SNMP requests. Bit 1 decided wether the community string of read operations is compare… |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.4.2 | ScalarwtWebioEA12x6RelSnmpCommunityStringRead | read-write | mandatory | Community string read only |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.4.3 | ScalarwtWebioEA12x6RelSnmpCommunityStringReadWrite | read-write | mandatory | Community string read / write |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.4.4 | ScalarwtWebioEA12x6RelSnmpSystemTrapManagerIP | read-write | mandatory | Name or IP address of the TCP server which accepts the system trap. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.4.5 | ScalarwtWebioEA12x6RelSnmpSystemTrapEnable | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2: Diag messages Bit 3-7: unused |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.5 | NodewtWebioEA12x6RelUDP | |||
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.5.1 | ScalarwtWebioEA12x6RelUdpAdminPort | read-write | mandatory | Udp port to which the Udp queries ( short form GET requests) can be sent. This port number must be unique within the device. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.5.2 | ScalarwtWebioEA12x6RelUdpEnable | read-write | mandatory | Set this bit to enable UDP support: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : UDP enable |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.5.3 | ScalarwtWebioEA12x6RelUdpRemotePort | read-write | mandatory | Udp remote port setting. If this value is set to zero, the source port read from a request will be used as destination port for the answer. A non zero value fo… |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.6 | NodewtWebioEA12x6RelBinary | |||
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.6.1 | ScalarwtWebioEA12x6RelBinaryModeCount | read-only | mandatory | Number of independent binary channels. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.6.2 | TablewtWebioEA12x6RelBinaryIfTable | not-accessible | mandatory | Table of indices. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.6.2.1 | RowwtWebioEA12x6RelBinaryIfEntry | not-accessible | mandatory | Indices of the binary channels. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.6.2.1.1 | ColumnwtWebioEA12x6RelBinaryModeNo | read-only | mandatory | Number of the binary channel. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.6.3 | TablewtWebioEA12x6RelBinaryTable | not-accessible | mandatory | Table of properties of the binary mode. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.6.3.1 | RowwtWebioEA12x6RelBinaryEntry | not-accessible | mandatory | Binary properties. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.6.3.1.1 | ColumnwtWebioEA12x6RelBinaryOperationMode | read-write | mandatory | Selection of the operation mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: … |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.6.3.1.2 | ColumnwtWebioEA12x6RelBinaryTcpServerLocalPort | read-write | mandatory | Local TCP port for data exchange in this server mode. This port number must be unique within the device. Reserved port number must not be used (refere to the m… |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.6.3.1.3 | ColumnwtWebioEA12x6RelBinaryTcpServerInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.6.3.1.4 | ColumnwtWebioEA12x6RelBinaryTcpServerApplicationMode | read-write | mandatory | Selection of the application mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4… |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.6.3.1.5 | ColumnwtWebioEA12x6RelBinaryTcpClientLocalPort | read-write | mandatory | Local TCP port for data exchange in this client mode. This port number must be unique within the device. Reserved port number must not be used (refere to the m… |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.6.3.1.6 | ColumnwtWebioEA12x6RelBinaryTcpClientServerPort | read-write | mandatory | Port number of the server. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when setting t… |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.6.3.1.7 | ColumnwtWebioEA12x6RelBinaryTcpClientServerIpAddr | read-write | mandatory | Ip address of the server. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when setting th… |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.6.3.1.8 | ColumnwtWebioEA12x6RelBinaryTcpClientServerPassword | read-write | mandatory | Building a connection may be protected by the administrator password of the server. Enter the server password to establish the connection, if a server administ… |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.6.3.1.9 | ColumnwtWebioEA12x6RelBinaryTcpClientInactivity | read-write | mandatory | Connection timeout in 100ms. If no data are exchanged within the specified time, the device closes the connection to the server. The value 0 deactivates the ti… |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.6.3.1.10 | ColumnwtWebioEA12x6RelBinaryTcpClientInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.6.3.1.11 | ColumnwtWebioEA12x6RelBinaryTcpClientInterval | read-write | mandatory | Configurable interval with a 100ms base, in which the Webio device sends data to the configured application. A interval of zero stopps the periodical sending. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.6.3.1.12 | ColumnwtWebioEA12x6RelBinaryTcpClientApplicationMode | read-write | mandatory | Selection of the application mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4… |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.6.3.1.13 | ColumnwtWebioEA12x6RelBinaryUdpPeerLocalPort | read-write | mandatory | Local UDP port for data exchange in this peer to peer mode. This port number must be unique within the device. Reserved port number must not be used (refere to… |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.6.3.1.14 | ColumnwtWebioEA12x6RelBinaryUdpPeerRemotePort | read-write | mandatory | Port number of the remote device. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when se… |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.6.3.1.15 | ColumnwtWebioEA12x6RelBinaryUdpPeerRemoteIpAddr | read-write | mandatory | Ip address of the remote device. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when set… |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.6.3.1.16 | ColumnwtWebioEA12x6RelBinaryUdpPeerInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.6.3.1.17 | ColumnwtWebioEA12x6RelBinaryUdpPeerInterval | read-write | mandatory | Configurable interval with a 100ms base, in which the Webio device sends data to the configured remote device. A interval of zero stopps the periodical sending. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.6.3.1.18 | ColumnwtWebioEA12x6RelBinaryUdpPeerApplicationMode | read-write | mandatory | Selection of the application mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4… |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.6.3.1.19 | ColumnwtWebioEA12x6RelBinaryConnectedPort | read-only | mandatory | Port number of the remote device, after connection has been established. In case of no connection or missing port informations a zero will be read. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.6.3.1.20 | ColumnwtWebioEA12x6RelBinaryConnectedIpAddr | read-only | mandatory | IP address of the remote device, after connection has been established. In case of no connection or missing port informations 0.0.0.0 will be read. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.6.3.1.21 | ColumnwtWebioEA12x6RelBinaryTcpServerClientHttpPort | read-write | mandatory | HTTP port number of the remote device at TCP Server Mode. If an mailfunction occurs status informations will be send to this port. Not used at mode Compatible … |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.6.3.1.22 | ColumnwtWebioEA12x6RelBinaryTcpClientServerHttpPort | read-write | mandatory | HTTP port number of the remote device at TCP Client Mode. In the operating mode Box2Box connection status informations will be exchanged through this port. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.7 | NodewtWebioEA12x6RelSyslog | |||
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.7.1 | ScalarwtWebioEA12x6RelSyslogServerIP | read-write | mandatory | Name or IP address of the Syslog server, which accepts the Syslog messgaes. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.7.2 | ScalarwtWebioEA12x6RelSyslogServerPort | read-write | mandatory | Portnumber of the Syslog servers, default 514. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.7.3 | ScalarwtWebioEA12x6RelSyslogSystemMessagesEnable | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2: Diag Messages Bit 3-7: unused |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.7.4 | ScalarwtWebioEA12x6RelSyslogEnable | read-write | mandatory | Set bit 0to enable Syslog: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Syslog enable |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.8 | NodewtWebioEA12x6RelFTP | |||
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.8.1 | ScalarwtWebioEA12x6RelFTPServerIP | read-write | mandatory | Name or IP address of the FTP server, which accepts the FTP messages. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.8.2 | ScalarwtWebioEA12x6RelFTPServerControlPort | read-write | mandatory | Portnumber of the control port of the FTP server, default 21. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.8.3 | ScalarwtWebioEA12x6RelFTPUserName | read-write | mandatory | FTP Loggin: user name. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.8.4 | ScalarwtWebioEA12x6RelFTPPassword | read-write | mandatory | FTP Loggin: user password. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.8.5 | ScalarwtWebioEA12x6RelFTPAccount | read-write | mandatory | FTP Loggin: name of account. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.8.6 | ScalarwtWebioEA12x6RelFTPOption | read-write | mandatory | Bit 0 switches the FTP Server in Passiv-Mode, the Client controls the data connection on its own: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit … |
| 1.3.6.1.4.1.5040.1.2.19.3.1.3.8.7 | ScalarwtWebioEA12x6RelFTPEnable | read-write | mandatory | Set Bit 0 to enable FTP: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : FTP enable |
| 1.3.6.1.4.1.5040.1.2.19.3.1.4 | NodewtWebioEA12x6RelOutputMode | |||
| 1.3.6.1.4.1.5040.1.2.19.3.1.4.1 | TablewtWebioEA12x6RelOutputModeTable | not-accessible | mandatory | Table of output mode configurations dependent on the output indices. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.4.1.1 | RowwtWebioEA12x6RelOutputModeEntry | not-accessible | mandatory | Output mode configurations of the individual outputs. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.4.1.1.1 | ColumnwtWebioEA12x6RelOutputModeBit | read-write | mandatory | This binary coded output mode defines the individual operation mode for any output. More than one mode must not be selected. The OCTETS are interpreted bit-by-… |
| 1.3.6.1.4.1.5040.1.2.19.3.1.4.2 | ScalarwtWebioEA12x6RelSafetyTimeout | read-write | mandatory | After this period of time (multiple of 100ms) without receiving data outputs switch to their Safety States. For each output a independend safety state could be… |
| 1.3.6.1.4.1.5040.1.2.19.3.1.5 | NodewtWebioEA12x6RelAlarm | |||
| 1.3.6.1.4.1.5040.1.2.19.3.1.5.1 | ScalarwtWebioEA12x6RelAlarmCount | read-only | mandatory | Number of independent alarms. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.5.2 | TablewtWebioEA12x6RelAlarmIfTable | not-accessible | mandatory | List of alarm indices. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.5.2.1 | RowwtWebioEA12x6RelAlarmIfEntry | not-accessible | mandatory | Numbers of the alarms. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.5.2.1.1 | ColumnwtWebioEA12x6RelAlarmNo | read-only | mandatory | Numbers of the alarms. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.5.3 | TablewtWebioEA12x6RelAlarmTable | not-accessible | mandatory | List of settings depending on the alarm number. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.5.3.1 | RowwtWebioEA12x6RelAlarmEntry | not-accessible | mandatory | Alarm parameters of the individual alarms. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.5.3.1.1 | ColumnwtWebioEA12x6RelAlarmInputTrigger | read-write | mandatory | This variable allows setting of individual input trigger conditions. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an input. Bit 0 corr… |
| 1.3.6.1.4.1.5040.1.2.19.3.1.5.3.1.2 | ColumnwtWebioEA12x6RelAlarmOutputTrigger | read-write | mandatory | This variable allows setting of individual output trigger conditions. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 co… |
| 1.3.6.1.4.1.5040.1.2.19.3.1.5.3.1.3 | ColumnwtWebioEA12x6RelAlarmSystemTrigger | read-write | mandatory | Binary coded trigger conditions: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, … |
| 1.3.6.1.4.1.5040.1.2.19.3.1.5.3.1.4 | ColumnwtWebioEA12x6RelAlarmMaxCounterValue | read-write | mandatory | This variable configures a max. counter value. If an input counter value exceeds this max. value, the corresponding alarm is triggered. Input counters with its… |
| 1.3.6.1.4.1.5040.1.2.19.3.1.5.3.1.5 | ColumnwtWebioEA12x6RelAlarmInterval | read-write | mandatory | Send interval for alarm messages. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.5.3.1.6 | ColumnwtWebioEA12x6RelAlarmEnable | read-write | mandatory | Binary coded alarm enable: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Mail Enable Bit 1: SNMP Trap enable Bit 2: UDP enable Bit 3: Send in… |
| 1.3.6.1.4.1.5040.1.2.19.3.1.5.3.1.7 | ColumnwtWebioEA12x6RelAlarmMailAddr | read-write | mandatory | E-Mail address for sending the alarm mail to. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.5.3.1.8 | ColumnwtWebioEA12x6RelAlarmMailSubject | read-write | mandatory | Subject line for alarm mail. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.5.3.1.9 | ColumnwtWebioEA12x6RelAlarmMailText | read-write | mandatory | Alarm mail text: States of the Webio device can be included by using special tags. Please refer to the respective Webio manual |
| 1.3.6.1.4.1.5040.1.2.19.3.1.5.3.1.10 | ColumnwtWebioEA12x6RelAlarmSnmpManagerIP | read-write | mandatory | IP address of the SNMP Manager to which the Webio device should send SNMP traps. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.5.3.1.11 | ColumnwtWebioEA12x6RelAlarmSnmpTrapText | read-write | mandatory | This text appears in the trap body. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.5.3.1.12 | ColumnwtWebioEA12x6RelAlarmUdpIpAddr | read-write | mandatory | IP address of the UDP listener to which the Webio device should send UDP traps. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.5.3.1.13 | ColumnwtWebioEA12x6RelAlarmUdpPort | read-write | mandatory | Port number of the UDP listener to which the Webio device should send UDP traps. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.5.3.1.14 | ColumnwtWebioEA12x6RelAlarmUdpText | read-write | mandatory | This text appears in the UDP trap body. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.5.3.1.15 | ColumnwtWebioEA12x6RelAlarmTcpIpAddr | read-write | mandatory | IP address of the TCP listener to which the Webio device should send TCP traps. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.5.3.1.16 | ColumnwtWebioEA12x6RelAlarmTcpPort | read-write | mandatory | Port number of the TCP listener to which the Webio device should send TCP traps. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.5.3.1.17 | ColumnwtWebioEA12x6RelAlarmTcpText | read-write | mandatory | This text appears in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.5.3.1.18 | ColumnwtWebioEA12x6RelAlarmSyslogIpAddr | read-write | mandatory | IP address of the syslog server to which the Webio device should send syslog messages. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.5.3.1.19 | ColumnwtWebioEA12x6RelAlarmSyslogPort | read-write | mandatory | Port number of the syslog server to which the Webio device should send syslog messages. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.5.3.1.20 | ColumnwtWebioEA12x6RelAlarmSyslogText | read-write | mandatory | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.5.3.1.21 | ColumnwtWebioEA12x6RelAlarmFtpDataPort | read-write | mandatory | Local data port: 1..65535 or AUTO: the next free port will be assigned. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.5.3.1.22 | ColumnwtWebioEA12x6RelAlarmFtpFileName | read-write | mandatory | Name of the file including path informations. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.5.3.1.23 | ColumnwtWebioEA12x6RelAlarmFtpText | read-write | mandatory | Message text to store on the FTP server. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.5.3.1.24 | ColumnwtWebioEA12x6RelAlarmFtpOption | read-write | mandatory | Binary coded options, select only one option at the same time: STORE = replace file APPEND = append message at the end of the file Octet 1: unused Octet 2: unu… |
| 1.3.6.1.4.1.5040.1.2.19.3.1.5.3.1.25 | ColumnwtWebioEA12x6RelAlarmTimerCron | read-write | mandatory | This entry contains 5 space or tab seperated text fields for time trigger definition. Each field must match with the actual time to trigger a message, weekday … |
| 1.3.6.1.4.1.5040.1.2.19.3.1.5.3.1.26 | ColumnwtWebioEA12x6RelAlarmMailReleaseSubject | read-write | mandatory | Subject line for alarm mail. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.5.3.1.27 | ColumnwtWebioEA12x6RelAlarmMailReleaseText | read-write | mandatory | Release Alarm mail text: States of the Webio device can be included by using special tags. Please refer to the respective Webio manual |
| 1.3.6.1.4.1.5040.1.2.19.3.1.5.3.1.28 | ColumnwtWebioEA12x6RelAlarmSnmpTrapReleaseText | read-write | mandatory | This text appears in the trap body. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.5.3.1.29 | ColumnwtWebioEA12x6RelAlarmUdpReleaseText | read-write | mandatory | This text appears in the UDP trap body. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.5.3.1.30 | ColumnwtWebioEA12x6RelAlarmTcpReleaseText | read-write | mandatory | This text appears in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.5.3.1.31 | ColumnwtWebioEA12x6RelAlarmSyslogReleaseText | read-write | mandatory | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body. |
| 1.3.6.1.4.1.5040.1.2.19.3.1.5.3.1.32 | ColumnwtWebioEA12x6RelAlarmFtpReleaseText | read-write | mandatory | Message text to store on the FTP server. |
| 1.3.6.1.4.1.5040.1.2.19.3.2 | NodewtWebioEA12x6RelPorts | |||
| 1.3.6.1.4.1.5040.1.2.19.3.2.1 | TablewtWebioEA12x6RelInputPortTable | not-accessible | mandatory | List of settings depending on the input number. |
| 1.3.6.1.4.1.5040.1.2.19.3.2.1.1 | RowwtWebioEA12x6RelInputPortEntry | not-accessible | mandatory | Input parameter for the individual inputs. |
| 1.3.6.1.4.1.5040.1.2.19.3.2.1.1.1 | ColumnwtWebioEA12x6RelPortInputName | read-write | mandatory | Name of the input. |
| 1.3.6.1.4.1.5040.1.2.19.3.2.1.1.2 | ColumnwtWebioEA12x6RelPortInputText | read-write | mandatory | Description of the input. |
| 1.3.6.1.4.1.5040.1.2.19.3.2.1.1.3 | ColumnwtWebioEA12x6RelPortInputMode | read-write | mandatory | Binary coded modes: Selecting short pulse detection enable by setting the corresponding bit to 1 enables interrupt support for counting. Only positive edges ar… |
| 1.3.6.1.4.1.5040.1.2.19.3.2.1.1.4 | ColumnwtWebioEA12x6RelPortInputFilter | read-write | mandatory | Pulses with a duration shorter than here specified (duration in 1/1000 sec), are ignored. |
| 1.3.6.1.4.1.5040.1.2.19.3.2.1.1.5 | ColumnwtWebioEA12x6RelPortInputBicountPulsePolarity | read-write | mandatory | This value defines the polarity of the input pulse. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 0 : negative polarity Bit 1 : positive polarit… |
| 1.3.6.1.4.1.5040.1.2.19.3.2.1.1.6 | ColumnwtWebioEA12x6RelPortInputBicountInactivTimeout | read-write | mandatory | Pulse chains with a duration shorter than here specified (in 1/10 sek), are ignored. |
| 1.3.6.1.4.1.5040.1.2.19.3.2.2 | TablewtWebioEA12x6RelOutputPortTable | not-accessible | mandatory | List of settings depending on the output number. |
| 1.3.6.1.4.1.5040.1.2.19.3.2.2.1 | RowwtWebioEA12x6RelOutputPortEntry | not-accessible | mandatory | Output parameters of the individual outputs. |
| 1.3.6.1.4.1.5040.1.2.19.3.2.2.1.1 | ColumnwtWebioEA12x6RelPortOutputName | read-write | mandatory | Name of the output. |
| 1.3.6.1.4.1.5040.1.2.19.3.2.2.1.2 | ColumnwtWebioEA12x6RelPortOutputText | read-write | mandatory | Description of the output. |
| 1.3.6.1.4.1.5040.1.2.19.3.2.2.1.3 | ColumnwtWebioEA12x6RelPortOutputGroupMode | read-write | mandatory | Unused in this device 57634 |
| 1.3.6.1.4.1.5040.1.2.19.3.2.2.1.4 | ColumnwtWebioEA12x6RelPortOutputSafetyState | read-write | mandatory | This variable allows setting of individual digital outputs. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds … |
| 1.3.6.1.4.1.5040.1.2.19.3.2.2.1.5 | ColumnwtWebioEA12x6RelPortLogicInputMask | read-write | mandatory | Selecting one of these inputs by setting the corresponding bit to 1 enables the logic function for the output identified by the index within this table. The ca… |
| 1.3.6.1.4.1.5040.1.2.19.3.2.2.1.6 | ColumnwtWebioEA12x6RelPortLogicInputInverter | read-write | mandatory | Every input bit selected here will be inverted. OCTET 1: unused OCTET 2: unused OCTET 3: Bit 0-3 : inputs 8-11 Bit 4-7 : unused OCTET 4: Bit 0-7 : inputs 0-7 |
| 1.3.6.1.4.1.5040.1.2.19.3.2.2.1.7 | ColumnwtWebioEA12x6RelPortLogicFunction | read-write | mandatory | This determines the logic function. No more than one function may be selected. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 0 : logic function … |
| 1.3.6.1.4.1.5040.1.2.19.3.2.2.1.8 | ColumnwtWebioEA12x6RelPortLogicOutputInverter | read-write | mandatory | The logical operation result could be inverteted by setting the corresponding bit to 1. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 0 : Output… |
| 1.3.6.1.4.1.5040.1.2.19.3.2.2.1.9 | ColumnwtWebioEA12x6RelPortPulseDuration | read-write | mandatory | Pulse length in 1/1000 sec. Setting this value to zero, disables the pulse output. |
| 1.3.6.1.4.1.5040.1.2.19.3.2.2.1.10 | ColumnwtWebioEA12x6RelPortPulsePolarity | read-write | mandatory | This value defines the polarity of the output pulse, if wtWebioEA12x6RelPortPulseDuration is not set to zero. After the pulse is finished, the output switches … |
| 1.3.6.1.4.1.5040.1.2.19.3.3 | NodewtWebioEA12x6RelManufact | |||
| 1.3.6.1.4.1.5040.1.2.19.3.3.1 | ScalarwtWebioEA12x6RelMfName | read-write | mandatory | Manufacturer company name |
| 1.3.6.1.4.1.5040.1.2.19.3.3.2 | ScalarwtWebioEA12x6RelMfAddr | read-write | mandatory | Manufacturer address. |
| 1.3.6.1.4.1.5040.1.2.19.3.3.3 | ScalarwtWebioEA12x6RelMfHotline | read-write | mandatory | Manufacturer hotline. |
| 1.3.6.1.4.1.5040.1.2.19.3.3.4 | ScalarwtWebioEA12x6RelMfInternet | read-write | mandatory | Manufacturer Internet address. |
| 1.3.6.1.4.1.5040.1.2.19.3.3.5 | ScalarwtWebioEA12x6RelMfDeviceTyp | read-write | mandatory | Manufacturer device name (model number). |
| 1.3.6.1.4.1.5040.1.2.19.3.3.6 | ScalarwtWebioEA12x6RelMfOrderNo | read-write | mandatory | Manufacturer part number. |
| 1.3.6.1.4.1.5040.1.2.19.4 | NodewtWebioEA12x6RelDiag | |||
| 1.3.6.1.4.1.5040.1.2.19.4.1 | ScalarwtWebioEA12x6RelDiagErrorCount | read-only | mandatory | Number of entries in the error memory. |
| 1.3.6.1.4.1.5040.1.2.19.4.2 | ScalarwtWebioEA12x6RelDiagBinaryError | read-only | mandatory | Error causes coded bit-by-bit. |
| 1.3.6.1.4.1.5040.1.2.19.4.3 | ScalarwtWebioEA12x6RelDiagErrorIndex | read-write | mandatory | The value of this variable is used as an index to read an error massege from wtWebioEA12x6RelDiagErrorMessage. Errors are numbered from 1 to wtWebioEA12x6RelDi… |
| 1.3.6.1.4.1.5040.1.2.19.4.4 | ScalarwtWebioEA12x6RelDiagErrorMessage | read-only | mandatory | Using wtWebioEA12x6RelDiagErrorIndex as an index, the appropriate message is available. |
| 1.3.6.1.4.1.5040.1.2.19.4.5 | ScalarwtWebioEA12x6RelDiagErrorClear | write-only | mandatory | Writing 1 into this variable clears all diagnosis messages. |
| 1.3.6.1.4.1.5040.1.2.19.41 | NodewtWebioEA12x6RelAlert1 | This SNMP trap is generated when Alarm 1 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.19.42 | NodewtWebioEA12x6RelAlert2 | This SNMP trap is generated when Alarm 2 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.19.43 | NodewtWebioEA12x6RelAlert3 | This SNMP trap is generated when Alarm 3 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.19.44 | NodewtWebioEA12x6RelAlert4 | This SNMP trap is generated when Alarm 4 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.19.45 | NodewtWebioEA12x6RelAlert5 | This SNMP trap is generated when Alarm 5 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.19.46 | NodewtWebioEA12x6RelAlert6 | This SNMP trap is generated when Alarm 6 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.19.47 | NodewtWebioEA12x6RelAlert7 | This SNMP trap is generated when Alarm 7 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.19.48 | NodewtWebioEA12x6RelAlert8 | This SNMP trap is generated when Alarm 8 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.19.49 | NodewtWebioEA12x6RelAlert9 | This SNMP trap is generated when Alarm 9 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.19.50 | NodewtWebioEA12x6RelAlert10 | This SNMP trap is generated when Alarm 10 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.19.51 | NodewtWebioEA12x6RelAlert11 | This SNMP trap is generated when Alarm 11 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.19.52 | NodewtWebioEA12x6RelAlert12 | This SNMP trap is generated when Alarm 12 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.19.71 | NodewtWebioEA12x6RelAlert13 | This SNMP trap is generated when Alarm 1 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.19.72 | NodewtWebioEA12x6RelAlert14 | This SNMP trap is generated when Alarm 2 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.19.73 | NodewtWebioEA12x6RelAlert15 | This SNMP trap is generated when Alarm 3 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.19.74 | NodewtWebioEA12x6RelAlert16 | This SNMP trap is generated when Alarm 4 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.19.75 | NodewtWebioEA12x6RelAlert17 | This SNMP trap is generated when Alarm 5 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.19.76 | NodewtWebioEA12x6RelAlert18 | This SNMP trap is generated when Alarm 6 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.19.77 | NodewtWebioEA12x6RelAlert19 | This SNMP trap is generated when Alarm 7 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.19.78 | NodewtWebioEA12x6RelAlert20 | This SNMP trap is generated when Alarm 8 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.19.79 | NodewtWebioEA12x6RelAlert21 | This SNMP trap is generated when Alarm 9 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.19.80 | NodewtWebioEA12x6RelAlert22 | This SNMP trap is generated when Alarm 10 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.19.81 | NodewtWebioEA12x6RelAlert23 | This SNMP trap is generated when Alarm 11 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.19.82 | NodewtWebioEA12x6RelAlert24 | This SNMP trap is generated when Alarm 12 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.19.110 | NodewtWebioEA12x6RelAlertDiag | This SNMP trap is generated when a diagnosis/error message was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.20 | NodewtWebAlarm6x6 | |||
| 1.3.6.1.4.1.5040.1.2.20.1 | NodewtWebAlarm6x6InOut | |||
| 1.3.6.1.4.1.5040.1.2.20.1.1 | ScalarwtWebAlarm6x6Inputs | read-only | mandatory | Number of idependent inputs. |
| 1.3.6.1.4.1.5040.1.2.20.1.2 | ScalarwtWebAlarm6x6Outputs | read-only | mandatory | Number of independent outputs. |
| 1.3.6.1.4.1.5040.1.2.20.1.3 | TablewtWebAlarm6x6InputTable | not-accessible | mandatory | List of input indices. |
| 1.3.6.1.4.1.5040.1.2.20.1.3.1 | RowwtWebAlarm6x6InputEntry | not-accessible | mandatory | Number of the inputs. |
| 1.3.6.1.4.1.5040.1.2.20.1.3.1.1 | ColumnwtWebAlarm6x6InputNo | read-only | mandatory | Index numbers of the inputs. |
| 1.3.6.1.4.1.5040.1.2.20.1.3.1.2 | ColumnwtWebAlarm6x6InputCounter | read-only | mandatory | Value of the input counter. |
| 1.3.6.1.4.1.5040.1.2.20.1.3.1.3 | ColumnwtWebAlarm6x6InputCounterClear | read-only | mandatory | Clears the input counter after returning its value. |
| 1.3.6.1.4.1.5040.1.2.20.1.3.1.4 | ColumnwtWebAlarm6x6InputState | read-only | mandatory | States of the inputs, 0-OFF, 1-ON. |
| 1.3.6.1.4.1.5040.1.2.20.1.4 | ScalarwtWebAlarm6x6InputValue | read-only | mandatory | This variable is used to read the inputs of the digital I/O port. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an input. Bit 0 corresp… |
| 1.3.6.1.4.1.5040.1.2.20.1.5 | TablewtWebAlarm6x6OutputTable | not-accessible | mandatory | List of output indices. |
| 1.3.6.1.4.1.5040.1.2.20.1.5.1 | RowwtWebAlarm6x6OutputEntry | not-accessible | mandatory | Number of the outputs. |
| 1.3.6.1.4.1.5040.1.2.20.1.5.1.1 | ColumnwtWebAlarm6x6OutputNo | read-only | mandatory | Output number. |
| 1.3.6.1.4.1.5040.1.2.20.1.5.1.2 | ColumnwtWebAlarm6x6OutputState | read-write | mandatory | States of the outputs, 0-OFF, 1-ON. |
| 1.3.6.1.4.1.5040.1.2.20.1.6 | ScalarwtWebAlarm6x6OutputValue | read-only | mandatory | This variable is used to read the outputs of the digital I/O port. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corre… |
| 1.3.6.1.4.1.5040.1.2.20.1.8 | TablewtWebAlarm6x6AlarmOutputTable | not-accessible | mandatory | List of alarm indices.. |
| 1.3.6.1.4.1.5040.1.2.20.1.8.1 | RowwtWebAlarm6x6AlarmOutputEntry | not-accessible | mandatory | Index reference. |
| 1.3.6.1.4.1.5040.1.2.20.1.8.1.1 | ColumnwtWebAlarm6x6AlarmOutputState | read-write | mandatory | State of the alarm, 0-OFF, 1-ON. |
| 1.3.6.1.4.1.5040.1.2.20.1.8.1.2 | ColumnwtWebAlarm6x6AlarmTriggerState | read-only | mandatory | State of the trigger condition, 0-OFF, 1-ON. |
| 1.3.6.1.4.1.5040.1.2.20.2 | NodewtWebAlarm6x6SessCntrl | |||
| 1.3.6.1.4.1.5040.1.2.20.2.1 | ScalarwtWebAlarm6x6SessCntrlPassword | read-write | mandatory | Entering this password opens a session which is ended by writing a 1 to wtWebAlarm6x6SessCntrlLogout. When read this variable provides a string of length zero. |
| 1.3.6.1.4.1.5040.1.2.20.2.2 | ScalarwtWebAlarm6x6SessCntrlConfigMode | read-only | mandatory | When the device is in SNMP configuration mode, the value 1 is returned, otherwise 0. If the read value is 0 even though the password was written, the device is… |
| 1.3.6.1.4.1.5040.1.2.20.2.3 | ScalarwtWebAlarm6x6SessCntrlLogout | read-write | mandatory | If the device is in configuration mode and the session was opened by this SNMP Manager, writing a 1 to this variable will end the session and all parameters ar… |
| 1.3.6.1.4.1.5040.1.2.20.2.4 | ScalarwtWebAlarm6x6SessCntrlAdminPassword | read-write | mandatory | This password protects access to the variables with administrator rights. It can only be changed by the administrator. If no password was assigned, the valid p… |
| 1.3.6.1.4.1.5040.1.2.20.2.5 | ScalarwtWebAlarm6x6SessCntrlConfigPassword | read-write | mandatory | This password protects access to the variables with configurator rights. It can be changed by the administrator and by the configurator. If no password was ass… |
| 1.3.6.1.4.1.5040.1.2.20.3 | NodewtWebAlarm6x6Config | |||
| 1.3.6.1.4.1.5040.1.2.20.3.1 | NodewtWebAlarm6x6Device | |||
| 1.3.6.1.4.1.5040.1.2.20.3.1.1 | NodewtWebAlarm6x6Text | |||
| 1.3.6.1.4.1.5040.1.2.20.3.1.1.1 | ScalarwtWebAlarm6x6DeviceName | read-write | mandatory | Name of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.1.2 | ScalarwtWebAlarm6x6DeviceText | read-write | mandatory | Description of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.1.3 | ScalarwtWebAlarm6x6DeviceLocation | read-write | mandatory | Description of the location of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.1.4 | ScalarwtWebAlarm6x6DeviceContact | read-write | mandatory | Contact address of the system operator of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.2 | NodewtWebAlarm6x6TimeDate | |||
| 1.3.6.1.4.1.5040.1.2.20.3.1.2.1 | NodewtWebAlarm6x6TimeZone | |||
| 1.3.6.1.4.1.5040.1.2.20.3.1.2.1.1 | ScalarwtWebAlarm6x6TzOffsetHrs | read-write | mandatory | Offset hours for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.2.1.2 | ScalarwtWebAlarm6x6TzOffsetMin | read-write | mandatory | Offset minutes for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.2.1.3 | ScalarwtWebAlarm6x6TzEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Timezone |
| 1.3.6.1.4.1.5040.1.2.20.3.1.2.1.4 | ScalarwtWebAlarm6x6StTzOffsetHrs | read-write | mandatory | Offset hours of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.2.1.5 | ScalarwtWebAlarm6x6StTzOffsetMin | read-write | mandatory | Offset minutes of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.2.1.6 | ScalarwtWebAlarm6x6StTzEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Summertime |
| 1.3.6.1.4.1.5040.1.2.20.3.1.2.1.7 | ScalarwtWebAlarm6x6StTzStartMonth | read-write | mandatory | Month in which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.2.1.8 | ScalarwtWebAlarm6x6StTzStartMode | read-write | mandatory | Mode of the day of the week for which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.2.1.9 | ScalarwtWebAlarm6x6StTzStartWday | read-write | mandatory | Day of the week on which the change is made from winter time to summer time |
| 1.3.6.1.4.1.5040.1.2.20.3.1.2.1.10 | ScalarwtWebAlarm6x6StTzStartHrs | read-write | mandatory | Hour in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.2.1.11 | ScalarwtWebAlarm6x6StTzStartMin | read-write | mandatory | Minute in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.2.1.12 | ScalarwtWebAlarm6x6StTzStopMonth | read-write | mandatory | Month in which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.2.1.13 | ScalarwtWebAlarm6x6StTzStopMode | read-write | mandatory | Mode of the week day on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.2.1.14 | ScalarwtWebAlarm6x6StTzStopWday | read-write | mandatory | Day of the week on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.2.1.15 | ScalarwtWebAlarm6x6StTzStopHrs | read-write | mandatory | Hour at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.2.1.16 | ScalarwtWebAlarm6x6StTzStopMin | read-write | mandatory | Minute at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.2.2 | NodewtWebAlarm6x6TimeServer | |||
| 1.3.6.1.4.1.5040.1.2.20.3.1.2.2.1 | ScalarwtWebAlarm6x6TimeServer1 | read-write | mandatory | IP address or name of the 1st time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.20.3.1.2.2.2 | ScalarwtWebAlarm6x6TimeServer2 | read-write | mandatory | IP address or name of the 2nd time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.20.3.1.2.2.3 | ScalarwtWebAlarm6x6TsEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Time Server |
| 1.3.6.1.4.1.5040.1.2.20.3.1.2.2.4 | ScalarwtWebAlarm6x6TsSyncTime | read-write | mandatory | Daily synchronisation time with the time server (hour: 0-23). |
| 1.3.6.1.4.1.5040.1.2.20.3.1.2.3 | NodewtWebAlarm6x6DeviceClock | |||
| 1.3.6.1.4.1.5040.1.2.20.3.1.2.3.1 | ScalarwtWebAlarm6x6ClockHrs | read-write | mandatory | Clock hours taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.2.3.2 | ScalarwtWebAlarm6x6ClockMin | read-write | mandatory | Clock minutes taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.2.3.3 | ScalarwtWebAlarm6x6ClockDay | read-write | mandatory | Date: Day of the month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.2.3.4 | ScalarwtWebAlarm6x6ClockMonth | read-write | mandatory | Date: Month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.2.3.5 | ScalarwtWebAlarm6x6ClockYear | read-write | mandatory | Date: Year, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.3 | NodewtWebAlarm6x6Basic | |||
| 1.3.6.1.4.1.5040.1.2.20.3.1.3.1 | NodewtWebAlarm6x6Network | |||
| 1.3.6.1.4.1.5040.1.2.20.3.1.3.1.1 | ScalarwtWebAlarm6x6IpAddress | read-write | mandatory | IP address of the Webio |
| 1.3.6.1.4.1.5040.1.2.20.3.1.3.1.2 | ScalarwtWebAlarm6x6SubnetMask | read-write | mandatory | Subnet mask of the Webio |
| 1.3.6.1.4.1.5040.1.2.20.3.1.3.1.3 | ScalarwtWebAlarm6x6Gateway | read-write | mandatory | Gateway of the Webio |
| 1.3.6.1.4.1.5040.1.2.20.3.1.3.1.4 | ScalarwtWebAlarm6x6DnsServer1 | read-write | mandatory | IP address of the 1st DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.20.3.1.3.1.5 | ScalarwtWebAlarm6x6DnsServer2 | read-write | mandatory | IP address of the 2nd DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.20.3.1.3.1.6 | ScalarwtWebAlarm6x6AddConfig | read-write | mandatory | Additional configuration (1=ON): Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1: DHCP enable Bit 0: BOOTP enable |
| 1.3.6.1.4.1.5040.1.2.20.3.1.3.2 | NodewtWebAlarm6x6HTTP | |||
| 1.3.6.1.4.1.5040.1.2.20.3.1.3.2.4 | ScalarwtWebAlarm6x6HttpPort | read-write | mandatory | Definition of the standard HTML port (Default: 80). |
| 1.3.6.1.4.1.5040.1.2.20.3.1.3.3 | NodewtWebAlarm6x6Mail | |||
| 1.3.6.1.4.1.5040.1.2.20.3.1.3.3.1 | ScalarwtWebAlarm6x6MailAdName | read-write | mandatory | Device name for mail administration. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.3.3.2 | ScalarwtWebAlarm6x6MailReply | read-write | mandatory | Reply address for the mail server. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.3.3.3 | ScalarwtWebAlarm6x6MailServer | read-write | mandatory | Name or IP address of the mail server. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.3.3.4 | ScalarwtWebAlarm6x6MailEnable | read-write | mandatory | Set this bit to enable the sending of mails: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Mail enable |
| 1.3.6.1.4.1.5040.1.2.20.3.1.3.3.5 | ScalarwtWebAlarm6x6MailAuthentication | read-write | mandatory | Selection of the authentication modi: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTE… |
| 1.3.6.1.4.1.5040.1.2.20.3.1.3.3.6 | ScalarwtWebAlarm6x6MailAuthUser | read-write | mandatory | Name of the user to be authenticated. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.3.3.7 | ScalarwtWebAlarm6x6MailAuthPassword | read-write | mandatory | Authentication password. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.3.3.8 | ScalarwtWebAlarm6x6MailPop3Server | read-write | mandatory | Name or Ip-address of the POP3 Servers. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.3.4 | NodewtWebAlarm6x6SNMP | |||
| 1.3.6.1.4.1.5040.1.2.20.3.1.3.4.1 | ScalarwtWebAlarm6x6SnmpEnable | read-write | mandatory | Set bit 0 to enable SNMP. If disabled, the device did not respond to any SNMP requests. Bit 1 decided wether the community string of read operations is compare… |
| 1.3.6.1.4.1.5040.1.2.20.3.1.3.4.2 | ScalarwtWebAlarm6x6SnmpCommunityStringRead | read-write | mandatory | Community string read only |
| 1.3.6.1.4.1.5040.1.2.20.3.1.3.4.3 | ScalarwtWebAlarm6x6SnmpCommunityStringReadWrite | read-write | mandatory | Community string read / write |
| 1.3.6.1.4.1.5040.1.2.20.3.1.3.4.4 | ScalarwtWebAlarm6x6SnmpSystemTrapManagerIP | read-write | mandatory | Name or IP address of the TCP server which accepts the system trap. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.3.4.5 | ScalarwtWebAlarm6x6SnmpSystemTrapEnable | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2: Diag messages Bit 3-7: unused |
| 1.3.6.1.4.1.5040.1.2.20.3.1.3.5 | NodewtWebAlarm6x6UDP | |||
| 1.3.6.1.4.1.5040.1.2.20.3.1.3.5.1 | ScalarwtWebAlarm6x6UdpAdminPort | read-write | mandatory | Udp port to which the Udp queries ( short form GET requests) can be sent. This port number must be unique within the device. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.3.5.2 | ScalarwtWebAlarm6x6UdpEnable | read-write | mandatory | Set this bit to enable UDP support: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : UDP enable |
| 1.3.6.1.4.1.5040.1.2.20.3.1.3.5.3 | ScalarwtWebAlarm6x6UdpRemotePort | read-write | mandatory | Udp remote port setting. If this value is set to zero, the source port read from a request will be used as destination port for the answer. A non zero value fo… |
| 1.3.6.1.4.1.5040.1.2.20.3.1.3.7 | NodewtWebAlarm6x6Syslog | |||
| 1.3.6.1.4.1.5040.1.2.20.3.1.3.7.1 | ScalarwtWebAlarm6x6SyslogServerIP | read-write | mandatory | Name or IP address of the Syslog server, which accepts the Syslog messgaes. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.3.7.2 | ScalarwtWebAlarm6x6SyslogServerPort | read-write | mandatory | Portnumber of the Syslog servers, default 514. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.3.7.3 | ScalarwtWebAlarm6x6SyslogSystemMessagesEnable | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2: Diag Messages Bit 3-7: unused |
| 1.3.6.1.4.1.5040.1.2.20.3.1.3.7.4 | ScalarwtWebAlarm6x6SyslogEnable | read-write | mandatory | Set bit 0to enable Syslog: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Syslog enable |
| 1.3.6.1.4.1.5040.1.2.20.3.1.3.8 | NodewtWebAlarm6x6FTP | |||
| 1.3.6.1.4.1.5040.1.2.20.3.1.3.8.1 | ScalarwtWebAlarm6x6FTPServerIP | read-write | mandatory | Name or IP address of the FTP server, which accepts the FTP messages. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.3.8.2 | ScalarwtWebAlarm6x6FTPServerControlPort | read-write | mandatory | Portnumber of the control port of the FTP server, default 21. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.3.8.3 | ScalarwtWebAlarm6x6FTPUserName | read-write | mandatory | FTP Loggin: user name. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.3.8.4 | ScalarwtWebAlarm6x6FTPPassword | read-write | mandatory | FTP Loggin: user password. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.3.8.5 | ScalarwtWebAlarm6x6FTPAccount | read-write | mandatory | FTP Loggin: name of account. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.3.8.6 | ScalarwtWebAlarm6x6FTPOption | read-write | mandatory | Bit 0 switches the FTP Server in Passiv-Mode, the Client controls the data connection on its own: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit … |
| 1.3.6.1.4.1.5040.1.2.20.3.1.3.8.7 | ScalarwtWebAlarm6x6FTPEnable | read-write | mandatory | Set Bit 0 to enable FTP: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : FTP enable |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5 | NodewtWebAlarm6x6Alarm | |||
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.1 | ScalarwtWebAlarm6x6AlarmCount | read-only | mandatory | Number of independent alarms. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.2 | TablewtWebAlarm6x6AlarmIfTable | not-accessible | mandatory | List of alarm indices. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.2.1 | RowwtWebAlarm6x6AlarmIfEntry | not-accessible | mandatory | Numbers of the alarms. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.2.1.1 | ColumnwtWebAlarm6x6AlarmNo | read-only | mandatory | Numbers of the alarms. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3 | TablewtWebAlarm6x6AlarmTable | not-accessible | mandatory | List of settings depending on the alarm number. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1 | RowwtWebAlarm6x6AlarmEntry | not-accessible | mandatory | Alarm parameters of the individual alarms. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.1 | ColumnwtWebAlarm6x6AlarmInputTrigger | read-write | mandatory | This variable allows setting of individual input trigger conditions. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an input. Bit 0 corr… |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.4 | ColumnwtWebAlarm6x6AlarmMaxCounterValue | read-write | mandatory | This variable configures a max. counter value. If an input counter value exceeds this max. value, the corresponding alarm is triggered. Input counters with its… |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.5 | ColumnwtWebAlarm6x6AlarmInterval | read-write | mandatory | Send interval for alarm messages. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.6 | ColumnwtWebAlarm6x6AlarmEnable | read-write | mandatory | Binary coded alarm enable: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Output Switch Enable Bit 1: Mail Enable Bit 2: SNMP Trap enable Bit … |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.7 | ColumnwtWebAlarm6x6AlarmMailAddr | read-write | mandatory | E-Mail address for sending the alarm mail to. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.8 | ColumnwtWebAlarm6x6AlarmMailSubject | read-write | mandatory | Subject line for alarm mail. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.9 | ColumnwtWebAlarm6x6AlarmMailText | read-write | mandatory | Alarm mail text: States of the Webio device can be included by using special tags. Please refer to the respective Webio manual |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.10 | ColumnwtWebAlarm6x6AlarmSnmpManagerIP | read-write | mandatory | IP address of the SNMP Manager to which the Webio device should send SNMP traps. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.11 | ColumnwtWebAlarm6x6AlarmSnmpTrapText | read-write | mandatory | This text appears in the trap body. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.12 | ColumnwtWebAlarm6x6AlarmUdpIpAddr | read-write | mandatory | IP address of the UDP listener to which the Webio device should send UDP traps. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.13 | ColumnwtWebAlarm6x6AlarmUdpPort | read-write | mandatory | Port number of the UDP listener to which the Webio device should send UDP traps. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.14 | ColumnwtWebAlarm6x6AlarmUdpText | read-write | mandatory | This text appears in the UDP trap body. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.15 | ColumnwtWebAlarm6x6AlarmTcpIpAddr | read-write | mandatory | IP address of the TCP listener to which the Webio device should send TCP traps. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.16 | ColumnwtWebAlarm6x6AlarmTcpPort | read-write | mandatory | Port number of the TCP listener to which the Webio device should send TCP traps. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.17 | ColumnwtWebAlarm6x6AlarmTcpText | read-write | mandatory | This text appears in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.18 | ColumnwtWebAlarm6x6AlarmSyslogIpAddr | read-write | mandatory | IP address of the syslog server to which the Webio device should send syslog messages. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.19 | ColumnwtWebAlarm6x6AlarmSyslogPort | read-write | mandatory | Port number of the syslog server to which the Webio device should send syslog messages. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.20 | ColumnwtWebAlarm6x6AlarmSyslogText | read-write | mandatory | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.21 | ColumnwtWebAlarm6x6AlarmFtpDataPort | read-write | mandatory | Local data port: 1..65535 or AUTO: the next free port will be assigned. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.22 | ColumnwtWebAlarm6x6AlarmFtpFileName | read-write | mandatory | Name of the file including path informations. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.23 | ColumnwtWebAlarm6x6AlarmFtpText | read-write | mandatory | Message text to store on the FTP server. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.24 | ColumnwtWebAlarm6x6AlarmFtpOption | read-write | mandatory | Binary coded options, select only one option at the same time: STORE = replace file APPEND = append message at the end of the file Octet 1: unused Octet 2: unu… |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.26 | ColumnwtWebAlarm6x6AlarmMailReleaseSubject | read-write | mandatory | Subject line for alarm mail. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.27 | ColumnwtWebAlarm6x6AlarmMailReleaseText | read-write | mandatory | Alarm mail text: States of the Webio device can be included by using special tags. Please refer to the respective Webio manual |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.28 | ColumnwtWebAlarm6x6AlarmSnmpTrapReleaseText | read-write | mandatory | This text appears in the trap body. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.29 | ColumnwtWebAlarm6x6AlarmUdpReleaseText | read-write | mandatory | This text appears in the UDP trap body. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.30 | ColumnwtWebAlarm6x6AlarmTcpReleaseText | read-write | mandatory | This text appears in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.31 | ColumnwtWebAlarm6x6AlarmSyslogReleaseText | read-write | mandatory | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.32 | ColumnwtWebAlarm6x6AlarmFtpReleaseText | read-write | mandatory | Message text to store on the FTP server. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.33 | ColumnwtWebAlarm6x6AlarmName | read-write | mandatory | Name of the alarm. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.34 | ColumnwtWebAlarm6x6AlarmGlobalEnable | read-write | mandatory | Binary coded alarm activation: Die OCTETS werden bitweise interpretiert. Bit 0 entspricht dem LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bit… |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.35 | ColumnwtWebAlarm6x6AlarmCounterClear | read-write | mandatory | Binary coded options: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bit 2-7: un… |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.36 | ColumnwtWebAlarm6x6AlarmAckEnable | read-write | mandatory | Binary coded options: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bit 2-7: un… |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.37 | ColumnwtWebAlarm6x6AlarmAckPort | read-write | mandatory | Number of the input, which clears the alarm (1-6). |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.38 | ColumnwtWebAlarm6x6AlarmSetPort | read-write | mandatory | Number of the output, which will be set by this alarm (1-6). The configuration of pulse mode and polarity defined in the port output section is used. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.39 | ColumnwtWebAlarm6x6AlarmMailTrgClearSubject | read-write | mandatory | Subject line for alarm mail. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.40 | ColumnwtWebAlarm6x6AlarmMailTrgClearText | read-write | mandatory | Alarm mail text: States of the Webio device can be included by using special tags. Please refer to the respective Webio manual |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.41 | ColumnwtWebAlarm6x6AlarmSnmpTrapTrgClearText | read-write | mandatory | This text appears in the trap body. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.42 | ColumnwtWebAlarm6x6AlarmUdpTrgClearText | read-write | mandatory | This text appears in the UDP trap body. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.43 | ColumnwtWebAlarm6x6AlarmTcpTrgClearText | read-write | mandatory | This text appears in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.44 | ColumnwtWebAlarm6x6AlarmSyslogTrgClearText | read-write | mandatory | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.45 | ColumnwtWebAlarm6x6AlarmFtpTrgClearText | read-write | mandatory | Message text to store on the FTP server. |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.46 | ColumnwtWebAlarm6x6AlarmMailTrapTxEnable | read-write | mandatory | Binary coded options: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bit 4-7: un… |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.47 | ColumnwtWebAlarm6x6AlarmSnmpTrapTrapTxEnable | read-write | mandatory | Binary coded options: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bit 4-7: un… |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.48 | ColumnwtWebAlarm6x6AlarmUdpTrapTxEnable | read-write | mandatory | Binary coded options: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bit 4-7: un… |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.49 | ColumnwtWebAlarm6x6AlarmTcpTrapTxEnable | read-write | mandatory | Binary coded options: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bit 4-7: un… |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.50 | ColumnwtWebAlarm6x6AlarmSyslogTrapTxEnable | read-write | mandatory | Binary coded options: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bit 4-7: un… |
| 1.3.6.1.4.1.5040.1.2.20.3.1.5.3.1.51 | ColumnwtWebAlarm6x6AlarmFtpTrapTxEnable | read-write | mandatory | Binary coded options: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bit 4-7: un… |
| 1.3.6.1.4.1.5040.1.2.20.3.2 | NodewtWebAlarm6x6Ports | |||
| 1.3.6.1.4.1.5040.1.2.20.3.2.1 | TablewtWebAlarm6x6InputPortTable | not-accessible | mandatory | List of settings depending on the input number. |
| 1.3.6.1.4.1.5040.1.2.20.3.2.1.1 | RowwtWebAlarm6x6InputPortEntry | not-accessible | mandatory | Input parameter for the individual inputs. |
| 1.3.6.1.4.1.5040.1.2.20.3.2.1.1.1 | ColumnwtWebAlarm6x6PortInputName | read-write | mandatory | Name of the input. |
| 1.3.6.1.4.1.5040.1.2.20.3.2.1.1.2 | ColumnwtWebAlarm6x6PortInputText | read-write | mandatory | Description of the input. |
| 1.3.6.1.4.1.5040.1.2.20.3.2.1.1.4 | ColumnwtWebAlarm6x6PortInputFilter | read-write | mandatory | Pulses with a duration shorter than here specified (duration in 1/1000 sec), are ignored. |
| 1.3.6.1.4.1.5040.1.2.20.3.2.1.1.5 | ColumnwtWebAlarm6x6PortInputPulsePolarity | read-write | mandatory | This value defines the polarity of the input pulse. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 0 : negative polarity Bit 1 : positive polarit… |
| 1.3.6.1.4.1.5040.1.2.20.3.2.1.1.7 | ColumnwtWebAlarm6x6PortInputCounterSet | read-write | mandatory | Writing to this variable presets the counter, while reading returns the actual value. |
| 1.3.6.1.4.1.5040.1.2.20.3.2.2 | TablewtWebAlarm6x6OutputPortTable | not-accessible | mandatory | List of settings depending on the output number. |
| 1.3.6.1.4.1.5040.1.2.20.3.2.2.1 | RowwtWebAlarm6x6OutputPortEntry | not-accessible | mandatory | Output parameters of the individual outputs. |
| 1.3.6.1.4.1.5040.1.2.20.3.2.2.1.1 | ColumnwtWebAlarm6x6PortOutputName | read-write | mandatory | Name of the output. |
| 1.3.6.1.4.1.5040.1.2.20.3.2.2.1.2 | ColumnwtWebAlarm6x6PortOutputText | read-write | mandatory | Description of the output. |
| 1.3.6.1.4.1.5040.1.2.20.3.2.2.1.9 | ColumnwtWebAlarm6x6PortPulseDuration | read-write | mandatory | Pulse length in 1/100 sec. Setting this value to zero, disables the pulse output. |
| 1.3.6.1.4.1.5040.1.2.20.3.2.2.1.10 | ColumnwtWebAlarm6x6PortPulsePolarity | read-write | mandatory | This value defines the polarity of the output pulse, if wtWebAlarm6x6PortPulseDuration is not set to zero. After the pulse is finished, the output switches bac… |
| 1.3.6.1.4.1.5040.1.2.20.3.3 | NodewtWebAlarm6x6Manufact | |||
| 1.3.6.1.4.1.5040.1.2.20.3.3.1 | ScalarwtWebAlarm6x6MfName | read-write | mandatory | Manufacturer company name |
| 1.3.6.1.4.1.5040.1.2.20.3.3.2 | ScalarwtWebAlarm6x6MfAddr | read-write | mandatory | Manufacturer address. |
| 1.3.6.1.4.1.5040.1.2.20.3.3.3 | ScalarwtWebAlarm6x6MfHotline | read-write | mandatory | Manufacturer hotline. |
| 1.3.6.1.4.1.5040.1.2.20.3.3.4 | ScalarwtWebAlarm6x6MfInternet | read-write | mandatory | Manufacturer Internet address. |
| 1.3.6.1.4.1.5040.1.2.20.3.3.5 | ScalarwtWebAlarm6x6MfDeviceTyp | read-write | mandatory | Manufacturer device name (model number). |
| 1.3.6.1.4.1.5040.1.2.20.3.3.6 | ScalarwtWebAlarm6x6MfOrderNo | read-write | mandatory | Manufacturer part number. |
| 1.3.6.1.4.1.5040.1.2.20.4 | NodewtWebAlarm6x6Diag | |||
| 1.3.6.1.4.1.5040.1.2.20.4.1 | ScalarwtWebAlarm6x6DiagErrorCount | read-only | mandatory | Number of entries in the error memory. |
| 1.3.6.1.4.1.5040.1.2.20.4.2 | ScalarwtWebAlarm6x6DiagBinaryError | read-only | mandatory | Error causes coded bit-by-bit. |
| 1.3.6.1.4.1.5040.1.2.20.4.3 | ScalarwtWebAlarm6x6DiagErrorIndex | read-write | mandatory | The value of this variable is used as an index to read an error massege from wtWebAlarm6x6DiagErrorMessage. Errors are numbered from 1 to wtWebAlarm6x6DiagErro… |
| 1.3.6.1.4.1.5040.1.2.20.4.4 | ScalarwtWebAlarm6x6DiagErrorMessage | read-only | mandatory | Using wtWebAlarm6x6DiagErrorIndex as an index, the appropriate message is available. |
| 1.3.6.1.4.1.5040.1.2.20.4.5 | ScalarwtWebAlarm6x6DiagErrorClear | write-only | mandatory | Writing 1 into this variable clears all diagnosis messages. |
| 1.3.6.1.4.1.5040.1.2.20.41 | NodewtWebAlarm6x6Alert1 | This SNMP trap is generated when Alarm 1 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.20.42 | NodewtWebAlarm6x6Alert2 | This SNMP trap is generated when Alarm 2 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.20.43 | NodewtWebAlarm6x6Alert3 | This SNMP trap is generated when Alarm 3 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.20.44 | NodewtWebAlarm6x6Alert4 | This SNMP trap is generated when Alarm 4 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.20.45 | NodewtWebAlarm6x6Alert5 | This SNMP trap is generated when Alarm 5 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.20.46 | NodewtWebAlarm6x6Alert6 | This SNMP trap is generated when Alarm 6 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.20.47 | NodewtWebAlarm6x6Alert7 | This SNMP trap is generated when Alarm 7 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.20.48 | NodewtWebAlarm6x6Alert8 | This SNMP trap is generated when Alarm 8 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.20.49 | NodewtWebAlarm6x6Alert9 | This SNMP trap is generated when Alarm 9 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.20.50 | NodewtWebAlarm6x6Alert10 | This SNMP trap is generated when Alarm 10 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.20.51 | NodewtWebAlarm6x6Alert11 | This SNMP trap is generated when Alarm 11 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.20.52 | NodewtWebAlarm6x6Alert12 | This SNMP trap is generated when Alarm 12 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.20.71 | NodewtWebAlarm6x6Alert13 | This SNMP trap is generated when Alarm 1 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.20.72 | NodewtWebAlarm6x6Alert14 | This SNMP trap is generated when Alarm 2 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.20.73 | NodewtWebAlarm6x6Alert15 | This SNMP trap is generated when Alarm 3 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.20.74 | NodewtWebAlarm6x6Alert16 | This SNMP trap is generated when Alarm 4 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.20.75 | NodewtWebAlarm6x6Alert17 | This SNMP trap is generated when Alarm 5 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.20.76 | NodewtWebAlarm6x6Alert18 | This SNMP trap is generated when Alarm 6 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.20.77 | NodewtWebAlarm6x6Alert19 | This SNMP trap is generated when Alarm 7 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.20.78 | NodewtWebAlarm6x6Alert20 | This SNMP trap is generated when Alarm 8 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.20.79 | NodewtWebAlarm6x6Alert21 | This SNMP trap is generated when Alarm 9 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.20.80 | NodewtWebAlarm6x6Alert22 | This SNMP trap is generated when Alarm 10 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.20.81 | NodewtWebAlarm6x6Alert23 | This SNMP trap is generated when Alarm 11 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.20.82 | NodewtWebAlarm6x6Alert24 | This SNMP trap is generated when Alarm 12 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.20.91 | NodewtWebAlarm6x6Alert25 | This SNMP trap is generated when the trigger of the Alarm 1 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.20.92 | NodewtWebAlarm6x6Alert26 | This SNMP trap is generated when the trigger of the Alarm 2 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.20.93 | NodewtWebAlarm6x6Alert27 | This SNMP trap is generated when the trigger of the Alarm 3 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.20.94 | NodewtWebAlarm6x6Alert28 | This SNMP trap is generated when the trigger of the Alarm 4 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.20.95 | NodewtWebAlarm6x6Alert29 | This SNMP trap is generated when the trigger of the Alarm 5 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.20.96 | NodewtWebAlarm6x6Alert30 | This SNMP trap is generated when the trigger of the Alarm 6 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.20.97 | NodewtWebAlarm6x6Alert31 | This SNMP trap is generated when the trigger of the Alarm 7 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.20.98 | NodewtWebAlarm6x6Alert32 | This SNMP trap is generated when the trigger of the Alarm 8 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.20.99 | NodewtWebAlarm6x6Alert33 | This SNMP trap is generated when the trigger of the Alarm 9 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.20.100 | NodewtWebAlarm6x6Alert34 | This SNMP trap is generated when the trigger of the Alarm 10 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.20.101 | NodewtWebAlarm6x6Alert35 | This SNMP trap is generated when the trigger of the Alarm 11 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.20.102 | NodewtWebAlarm6x6Alert36 | This SNMP trap is generated when the trigger of the Alarm 12 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.20.110 | NodewtWebAlarm6x6AlertDiag | This SNMP trap is generated when a diagnosis/error message was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.22 | NodewtWebCount6 | |||
| 1.3.6.1.4.1.5040.1.2.22.1 | NodewtWebCount6InOut | |||
| 1.3.6.1.4.1.5040.1.2.22.1.1 | ScalarwtWebCount6Inputs | read-only | mandatory | Number of idependent inputs. |
| 1.3.6.1.4.1.5040.1.2.22.1.2 | ScalarwtWebCount6Outputs | read-only | mandatory | Number of independent outputs. |
| 1.3.6.1.4.1.5040.1.2.22.1.3 | TablewtWebCount6InputTable | not-accessible | mandatory | List of input indices. |
| 1.3.6.1.4.1.5040.1.2.22.1.3.1 | RowwtWebCount6InputEntry | not-accessible | mandatory | Number of the inputs. |
| 1.3.6.1.4.1.5040.1.2.22.1.3.1.1 | ColumnwtWebCount6InputNo | read-only | mandatory | Index numbers of the inputs. |
| 1.3.6.1.4.1.5040.1.2.22.1.3.1.2 | ColumnwtWebCount6InputCounter | read-only | mandatory | Value of the input counter. |
| 1.3.6.1.4.1.5040.1.2.22.1.3.1.3 | ColumnwtWebCount6InputCounterClear | read-only | mandatory | Clears the input counter after returning its value. |
| 1.3.6.1.4.1.5040.1.2.22.1.3.1.4 | ColumnwtWebCount6InputState | read-only | mandatory | Tates of the inputs, 0-OFF, 1-ON. |
| 1.3.6.1.4.1.5040.1.2.22.1.4 | ScalarwtWebCount6InputValue | read-only | mandatory | This variable is used to read the inputs of the digital I/O port. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an input. Bit 0 corresp… |
| 1.3.6.1.4.1.5040.1.2.22.1.8 | TablewtWebCount6ReportOutputTable | not-accessible | mandatory | List of Report indices.. |
| 1.3.6.1.4.1.5040.1.2.22.1.8.1 | RowwtWebCount6ReportOutputEntry | not-accessible | mandatory | Index reference. |
| 1.3.6.1.4.1.5040.1.2.22.1.8.1.1 | ColumnwtWebCount6ReportOutputState | read-write | mandatory | State of the Report, 0-OFF, 1-ON. |
| 1.3.6.1.4.1.5040.1.2.22.1.8.1.2 | ColumnwtWebCount6ReportTriggerState | read-only | mandatory | State of the trigger condition, 0-OFF, 1-ON. |
| 1.3.6.1.4.1.5040.1.2.22.2 | NodewtWebCount6SessCntrl | |||
| 1.3.6.1.4.1.5040.1.2.22.2.1 | ScalarwtWebCount6SessCntrlPassword | read-write | mandatory | Entering this password opens a session which is ended by writing a 1 to wtWebCount6SessCntrlLogout. When read this variable provides a string of length zero. |
| 1.3.6.1.4.1.5040.1.2.22.2.2 | ScalarwtWebCount6SessCntrlConfigMode | read-only | mandatory | When the device is in SNMP configuration mode, the value 1 is returned, otherwise 0. If the read value is 0 even though the password was written, the device is… |
| 1.3.6.1.4.1.5040.1.2.22.2.3 | ScalarwtWebCount6SessCntrlLogout | read-write | mandatory | If the device is in configuration mode and the session was opened by this SNMP Manager, writing a 1 to this variable will end the session and all parameters ar… |
| 1.3.6.1.4.1.5040.1.2.22.2.4 | ScalarwtWebCount6SessCntrlAdminPassword | read-write | mandatory | This password protects access to the variables with administrator rights. It can only be changed by the administrator. If no password was assigned, the valid p… |
| 1.3.6.1.4.1.5040.1.2.22.2.5 | ScalarwtWebCount6SessCntrlConfigPassword | read-write | mandatory | This password protects access to the variables with configurator rights. It can be changed by the administrator and by the configurator. If no password was ass… |
| 1.3.6.1.4.1.5040.1.2.22.3 | NodewtWebCount6Config | |||
| 1.3.6.1.4.1.5040.1.2.22.3.1 | NodewtWebCount6Device | |||
| 1.3.6.1.4.1.5040.1.2.22.3.1.1 | NodewtWebCount6Text | |||
| 1.3.6.1.4.1.5040.1.2.22.3.1.1.1 | ScalarwtWebCount6DeviceName | read-write | mandatory | Name of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.1.2 | ScalarwtWebCount6DeviceText | read-write | mandatory | Description of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.1.3 | ScalarwtWebCount6DeviceLocation | read-write | mandatory | Description of the location of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.1.4 | ScalarwtWebCount6DeviceContact | read-write | mandatory | Contact address of the system operator of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.2 | NodewtWebCount6TimeDate | |||
| 1.3.6.1.4.1.5040.1.2.22.3.1.2.1 | NodewtWebCount6TimeZone | |||
| 1.3.6.1.4.1.5040.1.2.22.3.1.2.1.1 | ScalarwtWebCount6TzOffsetHrs | read-write | mandatory | Offset hours for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.2.1.2 | ScalarwtWebCount6TzOffsetMin | read-write | mandatory | Offset minutes for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.2.1.3 | ScalarwtWebCount6TzEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Timezone |
| 1.3.6.1.4.1.5040.1.2.22.3.1.2.1.4 | ScalarwtWebCount6StTzOffsetHrs | read-write | mandatory | Offset hours of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.2.1.5 | ScalarwtWebCount6StTzOffsetMin | read-write | mandatory | Offset minutes of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.2.1.6 | ScalarwtWebCount6StTzEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Summertime |
| 1.3.6.1.4.1.5040.1.2.22.3.1.2.1.7 | ScalarwtWebCount6StTzStartMonth | read-write | mandatory | Month in which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.2.1.8 | ScalarwtWebCount6StTzStartMode | read-write | mandatory | Mode of the day of the week for which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.2.1.9 | ScalarwtWebCount6StTzStartWday | read-write | mandatory | Day of the week on which the change is made from winter time to summer time |
| 1.3.6.1.4.1.5040.1.2.22.3.1.2.1.10 | ScalarwtWebCount6StTzStartHrs | read-write | mandatory | Hour in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.2.1.11 | ScalarwtWebCount6StTzStartMin | read-write | mandatory | Minute in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.2.1.12 | ScalarwtWebCount6StTzStopMonth | read-write | mandatory | Month in which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.2.1.13 | ScalarwtWebCount6StTzStopMode | read-write | mandatory | Mode of the week day on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.2.1.14 | ScalarwtWebCount6StTzStopWday | read-write | mandatory | Day of the week on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.2.1.15 | ScalarwtWebCount6StTzStopHrs | read-write | mandatory | Hour at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.2.1.16 | ScalarwtWebCount6StTzStopMin | read-write | mandatory | Minute at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.2.2 | NodewtWebCount6TimeServer | |||
| 1.3.6.1.4.1.5040.1.2.22.3.1.2.2.1 | ScalarwtWebCount6TimeServer1 | read-write | mandatory | IP address or name of the 1st time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.22.3.1.2.2.2 | ScalarwtWebCount6TimeServer2 | read-write | mandatory | IP address or name of the 2nd time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.22.3.1.2.2.3 | ScalarwtWebCount6TsEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Time Server |
| 1.3.6.1.4.1.5040.1.2.22.3.1.2.2.4 | ScalarwtWebCount6TsSyncTime | read-write | mandatory | Daily synchronisation time with the time server (hour: 0-23). |
| 1.3.6.1.4.1.5040.1.2.22.3.1.2.3 | NodewtWebCount6DeviceClock | |||
| 1.3.6.1.4.1.5040.1.2.22.3.1.2.3.1 | ScalarwtWebCount6ClockHrs | read-write | mandatory | Clock hours taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.2.3.2 | ScalarwtWebCount6ClockMin | read-write | mandatory | Clock minutes taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.2.3.3 | ScalarwtWebCount6ClockDay | read-write | mandatory | Date: Day of the month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.2.3.4 | ScalarwtWebCount6ClockMonth | read-write | mandatory | Date: Month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.2.3.5 | ScalarwtWebCount6ClockYear | read-write | mandatory | Date: Year, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.3 | NodewtWebCount6Basic | |||
| 1.3.6.1.4.1.5040.1.2.22.3.1.3.1 | NodewtWebCount6Network | |||
| 1.3.6.1.4.1.5040.1.2.22.3.1.3.1.1 | ScalarwtWebCount6IpAddress | read-write | mandatory | IP address of the Webio |
| 1.3.6.1.4.1.5040.1.2.22.3.1.3.1.2 | ScalarwtWebCount6SubnetMask | read-write | mandatory | Subnet mask of the Webio |
| 1.3.6.1.4.1.5040.1.2.22.3.1.3.1.3 | ScalarwtWebCount6Gateway | read-write | mandatory | Gateway of the Webio |
| 1.3.6.1.4.1.5040.1.2.22.3.1.3.1.4 | ScalarwtWebCount6DnsServer1 | read-write | mandatory | IP address of the 1st DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.22.3.1.3.1.5 | ScalarwtWebCount6DnsServer2 | read-write | mandatory | IP address of the 2nd DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.22.3.1.3.1.6 | ScalarwtWebCount6AddConfig | read-write | mandatory | Additional configuration (1=ON): Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1: DHCP enable Bit 0: BOOTP enable |
| 1.3.6.1.4.1.5040.1.2.22.3.1.3.2 | NodewtWebCount6HTTP | |||
| 1.3.6.1.4.1.5040.1.2.22.3.1.3.2.4 | ScalarwtWebCount6HttpPort | read-write | mandatory | Definition of the standard HTML port (Default: 80). |
| 1.3.6.1.4.1.5040.1.2.22.3.1.3.3 | NodewtWebCount6Mail | |||
| 1.3.6.1.4.1.5040.1.2.22.3.1.3.3.1 | ScalarwtWebCount6MailAdName | read-write | mandatory | Device name for mail administration. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.3.3.2 | ScalarwtWebCount6MailReply | read-write | mandatory | Reply address for the mail server. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.3.3.3 | ScalarwtWebCount6MailServer | read-write | mandatory | Name or IP address of the mail server. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.3.3.4 | ScalarwtWebCount6MailEnable | read-write | mandatory | Set this bit to enable the sending of mails: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Mail enable |
| 1.3.6.1.4.1.5040.1.2.22.3.1.3.3.5 | ScalarwtWebCount6MailAuthentication | read-write | mandatory | Selection of the authentication modi: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTE… |
| 1.3.6.1.4.1.5040.1.2.22.3.1.3.3.6 | ScalarwtWebCount6MailAuthUser | read-write | mandatory | Name of the user to be authenticated. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.3.3.7 | ScalarwtWebCount6MailAuthPassword | read-write | mandatory | Authentication password. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.3.3.8 | ScalarwtWebCount6MailPop3Server | read-write | mandatory | Name or Ip-address of the POP3 Servers. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.3.4 | NodewtWebCount6SNMP | |||
| 1.3.6.1.4.1.5040.1.2.22.3.1.3.4.1 | ScalarwtWebCount6SnmpEnable | read-write | mandatory | Set bit 0 to enable SNMP. If disabled, the device did not respond to any SNMP requests. Bit 1 decided wether the community string of read operations is compare… |
| 1.3.6.1.4.1.5040.1.2.22.3.1.3.4.2 | ScalarwtWebCount6SnmpCommunityStringRead | read-write | mandatory | Community string read only |
| 1.3.6.1.4.1.5040.1.2.22.3.1.3.4.3 | ScalarwtWebCount6SnmpCommunityStringReadWrite | read-write | mandatory | Community string read / write |
| 1.3.6.1.4.1.5040.1.2.22.3.1.3.4.4 | ScalarwtWebCount6SnmpSystemTrapManagerIP | read-write | mandatory | Name or IP address of the TCP server which accepts the system trap. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.3.4.5 | ScalarwtWebCount6SnmpSystemTrapEnable | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2: Diag messages Bit 3-7: unused |
| 1.3.6.1.4.1.5040.1.2.22.3.1.3.5 | NodewtWebCount6UDP | |||
| 1.3.6.1.4.1.5040.1.2.22.3.1.3.5.1 | ScalarwtWebCount6UdpAdminPort | read-write | mandatory | Udp port to which the Udp queries ( short form GET requests) can be sent. This port number must be unique within the device. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.3.5.2 | ScalarwtWebCount6UdpEnable | read-write | mandatory | Set this bit to enable UDP support: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : UDP enable |
| 1.3.6.1.4.1.5040.1.2.22.3.1.3.5.3 | ScalarwtWebCount6UdpRemotePort | read-write | mandatory | Udp remote port setting. If this value is set to zero, the source port read from a request will be used as destination port for the answer. A non zero value fo… |
| 1.3.6.1.4.1.5040.1.2.22.3.1.3.7 | NodewtWebCount6Syslog | |||
| 1.3.6.1.4.1.5040.1.2.22.3.1.3.7.1 | ScalarwtWebCount6SyslogServerIP | read-write | mandatory | Name or IP address of the Syslog server, which accepts the Syslog messgaes. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.3.7.2 | ScalarwtWebCount6SyslogServerPort | read-write | mandatory | Portnumber of the Syslog servers, default 514. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.3.7.3 | ScalarwtWebCount6SyslogSystemMessagesEnable | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2: Diag Messages Bit 3-7: unused |
| 1.3.6.1.4.1.5040.1.2.22.3.1.3.7.4 | ScalarwtWebCount6SyslogEnable | read-write | mandatory | Set bit 0to enable Syslog: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Syslog enable |
| 1.3.6.1.4.1.5040.1.2.22.3.1.3.8 | NodewtWebCount6FTP | |||
| 1.3.6.1.4.1.5040.1.2.22.3.1.3.8.1 | ScalarwtWebCount6FTPServerIP | read-write | mandatory | Name or IP address of the FTP server, which accepts the FTP messages. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.3.8.2 | ScalarwtWebCount6FTPServerControlPort | read-write | mandatory | Portnumber of the control port of the FTP server, default 21. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.3.8.3 | ScalarwtWebCount6FTPUserName | read-write | mandatory | FTP Loggin: user name. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.3.8.4 | ScalarwtWebCount6FTPPassword | read-write | mandatory | FTP Loggin: user password. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.3.8.5 | ScalarwtWebCount6FTPAccount | read-write | mandatory | FTP Loggin: name of account. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.3.8.6 | ScalarwtWebCount6FTPOption | read-write | mandatory | Bit 0 switches the FTP Server in Passiv-Mode, the Client controls the data connection on its own: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit … |
| 1.3.6.1.4.1.5040.1.2.22.3.1.3.8.7 | ScalarwtWebCount6FTPEnable | read-write | mandatory | Set Bit 0 to enable FTP: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : FTP enable |
| 1.3.6.1.4.1.5040.1.2.22.3.1.5 | NodewtWebCount6Report | |||
| 1.3.6.1.4.1.5040.1.2.22.3.1.5.1 | ScalarwtWebCount6ReportCount | read-only | mandatory | Number of independent Reports. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.5.2 | TablewtWebCount6ReportIfTable | not-accessible | mandatory | List of Report indices. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.5.2.1 | RowwtWebCount6ReportIfEntry | not-accessible | mandatory | Numbers of the Reports. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.5.2.1.1 | ColumnwtWebCount6ReportNo | read-only | mandatory | Numbers of the Reports. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.5.3 | TablewtWebCount6ReportTable | not-accessible | mandatory | List of settings depending on the Report number. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.5.3.1 | RowwtWebCount6ReportEntry | not-accessible | mandatory | Report parameters of the individual Reports. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.5.3.1.1 | ColumnwtWebCount6ReportInputTrigger | read-write | mandatory | This variable allows setting of individual input trigger conditions. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an input. Bit 0 corr… |
| 1.3.6.1.4.1.5040.1.2.22.3.1.5.3.1.3 | ColumnwtWebCount6ReportSystemTrigger | read-write | mandatory | Binary coded trigger conditions: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, … |
| 1.3.6.1.4.1.5040.1.2.22.3.1.5.3.1.4 | ColumnwtWebCount6ReportMaxCounterValue | read-write | mandatory | This variable configures a max. counter value. If an input counter value exceeds this max. value, the corresponding Report is triggered. Input counters with it… |
| 1.3.6.1.4.1.5040.1.2.22.3.1.5.3.1.5 | ColumnwtWebCount6ReportInterval | read-write | mandatory | Send interval for Report messages. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.5.3.1.6 | ColumnwtWebCount6ReportEnable | read-write | mandatory | Binary coded Report enable: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Output Switch Enable Bit 1: Mail Enable Bit 2: SNMP Trap enable Bit… |
| 1.3.6.1.4.1.5040.1.2.22.3.1.5.3.1.7 | ColumnwtWebCount6ReportMailAddr | read-write | mandatory | E-Mail address for sending the Report mail to. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.5.3.1.8 | ColumnwtWebCount6ReportMailSubject | read-write | mandatory | Subject line for Report mail. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.5.3.1.9 | ColumnwtWebCount6ReportMailText | read-write | mandatory | Report mail text: States of the Webio device can be included by using special tags. Please refer to the respective Webio manual |
| 1.3.6.1.4.1.5040.1.2.22.3.1.5.3.1.10 | ColumnwtWebCount6ReportSnmpManagerIP | read-write | mandatory | IP address of the SNMP Manager to which the Webio device should send SNMP traps. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.5.3.1.11 | ColumnwtWebCount6ReportSnmpTrapText | read-write | mandatory | This text appears in the trap body. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.5.3.1.12 | ColumnwtWebCount6ReportUdpIpAddr | read-write | mandatory | IP address of the UDP listener to which the Webio device should send UDP traps. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.5.3.1.13 | ColumnwtWebCount6ReportUdpPort | read-write | mandatory | Port number of the UDP listener to which the Webio device should send UDP traps. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.5.3.1.14 | ColumnwtWebCount6ReportUdpText | read-write | mandatory | This text appears in the UDP trap body. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.5.3.1.15 | ColumnwtWebCount6ReportTcpIpAddr | read-write | mandatory | IP address of the TCP listener to which the Webio device should send TCP traps. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.5.3.1.16 | ColumnwtWebCount6ReportTcpPort | read-write | mandatory | Port number of the TCP listener to which the Webio device should send TCP traps. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.5.3.1.17 | ColumnwtWebCount6ReportTcpText | read-write | mandatory | This text appears in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.5.3.1.18 | ColumnwtWebCount6ReportSyslogIpAddr | read-write | mandatory | IP address of the syslog server to which the Webio device should send syslog messages. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.5.3.1.19 | ColumnwtWebCount6ReportSyslogPort | read-write | mandatory | Port number of the syslog server to which the Webio device should send syslog messages. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.5.3.1.20 | ColumnwtWebCount6ReportSyslogText | read-write | mandatory | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.5.3.1.21 | ColumnwtWebCount6ReportFtpDataPort | read-write | mandatory | Local data port: 1..65535 or AUTO: the next free port will be assigned. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.5.3.1.22 | ColumnwtWebCount6ReportFtpFileName | read-write | mandatory | Name of the file including path informations. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.5.3.1.23 | ColumnwtWebCount6ReportFtpText | read-write | mandatory | Message text to store on the FTP server. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.5.3.1.24 | ColumnwtWebCount6ReportFtpOption | read-write | mandatory | Binary coded options, select only one option at the same time: STORE = replace file APPEND = append message at the end of the file Octet 1: unused Octet 2: unu… |
| 1.3.6.1.4.1.5040.1.2.22.3.1.5.3.1.25 | ColumnwtWebCount6ReportTimerCron | read-write | mandatory | This entry contains 5 space or tab seperated text fields for time trigger definition. Each field must match with the actual time to trigger a report, weekday a… |
| 1.3.6.1.4.1.5040.1.2.22.3.1.5.3.1.33 | ColumnwtWebCount6ReportName | read-write | mandatory | Name of the Report. |
| 1.3.6.1.4.1.5040.1.2.22.3.1.5.3.1.34 | ColumnwtWebCount6ReportGlobalEnable | read-write | mandatory | Binary coded Report activation: Die OCTETS werden bitweise interpretiert. Bit 0 entspricht dem LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bi… |
| 1.3.6.1.4.1.5040.1.2.22.3.1.5.3.1.35 | ColumnwtWebCount6ReportCounterClear | read-write | mandatory | Binary coded options: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bit 1-7: un… |
| 1.3.6.1.4.1.5040.1.2.22.3.1.5.3.1.52 | ColumnwtWebCount6ReportRateOfChange | read-write | mandatory | This variable configures a max. counter value within a time slot. If an input counter value exceeds this max. value, the corresponding Report is triggered. Inp… |
| 1.3.6.1.4.1.5040.1.2.22.3.1.5.3.1.53 | ColumnwtWebCount6ReportRateOfChangeWindow | read-write | mandatory | This variable configures the time slot of wtWebCount6ReportRateOfChange. Input counters with its mask bit unset in wtWebCount6ReportInputTrigger are not consid… |
| 1.3.6.1.4.1.5040.1.2.22.3.1.5.3.1.54 | ColumnwtWebCount6ReportRateOfChangeMode | read-write | mandatory | Binary coded options: Minimum mode: a report will be send if the count of pulses is lower than the given pulse count in wtWebCount6ReportRateOfChange. Maximum … |
| 1.3.6.1.4.1.5040.1.2.22.3.2 | NodewtWebCount6Ports | |||
| 1.3.6.1.4.1.5040.1.2.22.3.2.1 | TablewtWebCount6InputPortTable | not-accessible | mandatory | List of settings depending on the input number. |
| 1.3.6.1.4.1.5040.1.2.22.3.2.1.1 | RowwtWebCount6InputPortEntry | not-accessible | mandatory | Input parameter for the individual inputs. |
| 1.3.6.1.4.1.5040.1.2.22.3.2.1.1.1 | ColumnwtWebCount6PortInputName | read-write | mandatory | Name of the input. |
| 1.3.6.1.4.1.5040.1.2.22.3.2.1.1.2 | ColumnwtWebCount6PortInputText | read-write | mandatory | Description of the input. |
| 1.3.6.1.4.1.5040.1.2.22.3.2.1.1.3 | ColumnwtWebCount6PortInputMode | read-write | mandatory | Binary coded modes: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. Selection for input 0-1: OCTET 1: unused OCTET 2: unused OCTET 3: unus… |
| 1.3.6.1.4.1.5040.1.2.22.3.2.1.1.4 | ColumnwtWebCount6PortInputFilter | read-write | mandatory | Pulses with a duration shorter than here specified (duration in 1/1000 sec), are ignored. |
| 1.3.6.1.4.1.5040.1.2.22.3.2.1.1.5 | ColumnwtWebCount6PortInputPulsePolarity | read-write | mandatory | This value defines the polarity of the input pulse. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 0 : negative polarity Bit 1 : positive polarit… |
| 1.3.6.1.4.1.5040.1.2.22.3.2.1.1.6 | ColumnwtWebCount6PortInputBicountInactivTimeout | read-write | mandatory | Pulse chains with a duration shorter than here specified (in 1/10 sek), are ignored. |
| 1.3.6.1.4.1.5040.1.2.22.3.2.1.1.7 | ColumnwtWebCount6PortInputCounterSet | read-write | mandatory | Writing to this variable presets the counter, while reading returns the actual value. |
| 1.3.6.1.4.1.5040.1.2.22.3.2.1.1.8 | ColumnwtWebCount6PortInputCounterScale | read-write | mandatory | Conversion factor for this counter. |
| 1.3.6.1.4.1.5040.1.2.22.3.2.1.1.9 | ColumnwtWebCount6PortInputCounterUnit | read-write | mandatory | Unit for this counter. |
| 1.3.6.1.4.1.5040.1.2.22.3.3 | NodewtWebCount6Manufact | |||
| 1.3.6.1.4.1.5040.1.2.22.3.3.1 | ScalarwtWebCount6MfName | read-write | mandatory | Manufacturer company name |
| 1.3.6.1.4.1.5040.1.2.22.3.3.2 | ScalarwtWebCount6MfAddr | read-write | mandatory | Manufacturer address. |
| 1.3.6.1.4.1.5040.1.2.22.3.3.3 | ScalarwtWebCount6MfHotline | read-write | mandatory | Manufacturer hotline. |
| 1.3.6.1.4.1.5040.1.2.22.3.3.4 | ScalarwtWebCount6MfInternet | read-write | mandatory | Manufacturer Internet address. |
| 1.3.6.1.4.1.5040.1.2.22.3.3.5 | ScalarwtWebCount6MfDeviceTyp | read-write | mandatory | Manufacturer device name (model number). |
| 1.3.6.1.4.1.5040.1.2.22.3.3.6 | ScalarwtWebCount6MfOrderNo | read-write | mandatory | Manufacturer part number. |
| 1.3.6.1.4.1.5040.1.2.22.4 | NodewtWebCount6Diag | |||
| 1.3.6.1.4.1.5040.1.2.22.4.1 | ScalarwtWebCount6DiagErrorCount | read-only | mandatory | Number of entries in the error memory. |
| 1.3.6.1.4.1.5040.1.2.22.4.2 | ScalarwtWebCount6DiagBinaryError | read-only | mandatory | Error causes coded bit-by-bit. |
| 1.3.6.1.4.1.5040.1.2.22.4.3 | ScalarwtWebCount6DiagErrorIndex | read-write | mandatory | The value of this variable is used as an index to read an error massege from wtWebCount6DiagErrorMessage. Errors are numbered from 1 to wtWebCount6DiagErrorCou… |
| 1.3.6.1.4.1.5040.1.2.22.4.4 | ScalarwtWebCount6DiagErrorMessage | read-only | mandatory | Using wtWebCount6DiagErrorIndex as an index, the appropriate message is available. |
| 1.3.6.1.4.1.5040.1.2.22.4.5 | ScalarwtWebCount6DiagErrorClear | write-only | mandatory | Writing 1 into this variable clears all diagnosis messages. |
| 1.3.6.1.4.1.5040.1.2.22.41 | NodewtWebCount6Alert1 | This SNMP trap is generated when Report 1 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.22.42 | NodewtWebCount6Alert2 | This SNMP trap is generated when Report 2 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.22.43 | NodewtWebCount6Alert3 | This SNMP trap is generated when Report 3 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.22.44 | NodewtWebCount6Alert4 | This SNMP trap is generated when Report 4 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.22.45 | NodewtWebCount6Alert5 | This SNMP trap is generated when Report 5 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.22.46 | NodewtWebCount6Alert6 | This SNMP trap is generated when Report 6 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.22.47 | NodewtWebCount6Alert7 | This SNMP trap is generated when Report 7 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.22.48 | NodewtWebCount6Alert8 | This SNMP trap is generated when Report 8 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.22.49 | NodewtWebCount6Alert9 | This SNMP trap is generated when Report 9 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.22.50 | NodewtWebCount6Alert10 | This SNMP trap is generated when Report 10 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.22.51 | NodewtWebCount6Alert11 | This SNMP trap is generated when Report 11 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.22.52 | NodewtWebCount6Alert12 | This SNMP trap is generated when Report 12 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.22.110 | NodewtWebCount6AlertDiag | This SNMP trap is generated when a diagnosis/error message was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.24 | NodewtWebioEA6x6 | |||
| 1.3.6.1.4.1.5040.1.2.24.1 | NodewtWebioEA6x6InOut | |||
| 1.3.6.1.4.1.5040.1.2.24.1.1 | ScalarwtWebioEA6x6Inputs | read-only | mandatory | Number of idependent inputs. |
| 1.3.6.1.4.1.5040.1.2.24.1.2 | ScalarwtWebioEA6x6Outputs | read-only | mandatory | Number of idependent outputs. |
| 1.3.6.1.4.1.5040.1.2.24.1.3 | TablewtWebioEA6x6InputTable | not-accessible | mandatory | List of input indices. |
| 1.3.6.1.4.1.5040.1.2.24.1.3.1 | RowwtWebioEA6x6InputEntry | not-accessible | mandatory | Number of the inputs. |
| 1.3.6.1.4.1.5040.1.2.24.1.3.1.1 | ColumnwtWebioEA6x6InputNo | read-only | mandatory | Index numbers of the inputs. |
| 1.3.6.1.4.1.5040.1.2.24.1.3.1.2 | ColumnwtWebioEA6x6InputCounter | read-only | mandatory | Value of the input counter. |
| 1.3.6.1.4.1.5040.1.2.24.1.3.1.3 | ColumnwtWebioEA6x6InputCounterClear | read-only | mandatory | Clears the input counter after returning its value. |
| 1.3.6.1.4.1.5040.1.2.24.1.3.1.4 | ColumnwtWebioEA6x6InputState | read-only | mandatory | Value of a single input bit, 0-OFF, 1-ON. |
| 1.3.6.1.4.1.5040.1.2.24.1.4 | ScalarwtWebioEA6x6InputValue | read-only | mandatory | This variable is used to read the inputs of the digital I/O port. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corres… |
| 1.3.6.1.4.1.5040.1.2.24.1.5 | TablewtWebioEA6x6OutputTable | not-accessible | mandatory | List of output indices. |
| 1.3.6.1.4.1.5040.1.2.24.1.5.1 | RowwtWebioEA6x6OutputEntry | not-accessible | mandatory | Number of the outputs. |
| 1.3.6.1.4.1.5040.1.2.24.1.5.1.1 | ColumnwtWebioEA6x6OutputNo | read-only | mandatory | Output number. |
| 1.3.6.1.4.1.5040.1.2.24.1.5.1.2 | ColumnwtWebioEA6x6OutputState | read-write | mandatory | Value of a single output bit, 0-OFF, 1-ON. |
| 1.3.6.1.4.1.5040.1.2.24.1.6 | ScalarwtWebioEA6x6OutputValue | read-write | mandatory | This variable is used to read and write the outputs of the digital I/O port. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. B… |
| 1.3.6.1.4.1.5040.1.2.24.1.7 | ScalarwtWebioEA6x6SetOutput | read-write | mandatory | This variable allows setting of individual digital outputs. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds … |
| 1.3.6.1.4.1.5040.1.2.24.2 | NodewtWebioEA6x6SessCntrl | |||
| 1.3.6.1.4.1.5040.1.2.24.2.1 | ScalarwtWebioEA6x6SessCntrlPassword | read-write | mandatory | Entering this password opens a session which is ended by writing a 1 to wtWebioEA6x6SessCntrlLogout. When read this variable provides a string of length zero. |
| 1.3.6.1.4.1.5040.1.2.24.2.2 | ScalarwtWebioEA6x6SessCntrlConfigMode | read-only | mandatory | When the device is in SNMP configuration mode, the value 1 is returned, otherwise 0. If the read value is 0 even though the password was written, the device is… |
| 1.3.6.1.4.1.5040.1.2.24.2.3 | ScalarwtWebioEA6x6SessCntrlLogout | read-write | mandatory | If the device is in configuration mode and the session was opened by this SNMP Manager, writing a 1 to this variable will end the session and all parameters ar… |
| 1.3.6.1.4.1.5040.1.2.24.2.4 | ScalarwtWebioEA6x6SessCntrlAdminPassword | read-write | mandatory | This password protects access to the variables with administrator rights. It can only be changed by the administrator. If no password was assigned, the valid p… |
| 1.3.6.1.4.1.5040.1.2.24.2.5 | ScalarwtWebioEA6x6SessCntrlConfigPassword | read-write | mandatory | This password protects access to the variables with configurator rights. It can be changed by the administrator and by the configurator. If no password was ass… |
| 1.3.6.1.4.1.5040.1.2.24.3 | NodewtWebioEA6x6Config | |||
| 1.3.6.1.4.1.5040.1.2.24.3.1 | NodewtWebioEA6x6Device | |||
| 1.3.6.1.4.1.5040.1.2.24.3.1.1 | NodewtWebioEA6x6Text | |||
| 1.3.6.1.4.1.5040.1.2.24.3.1.1.1 | ScalarwtWebioEA6x6DeviceName | read-write | mandatory | Name of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.1.2 | ScalarwtWebioEA6x6DeviceText | read-write | mandatory | Description of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.1.3 | ScalarwtWebioEA6x6DeviceLocation | read-write | mandatory | Description of the location of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.1.4 | ScalarwtWebioEA6x6DeviceContact | read-write | mandatory | Contact address of the system operator of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.2 | NodewtWebioEA6x6TimeDate | |||
| 1.3.6.1.4.1.5040.1.2.24.3.1.2.1 | NodewtWebioEA6x6TimeZone | |||
| 1.3.6.1.4.1.5040.1.2.24.3.1.2.1.1 | ScalarwtWebioEA6x6TzOffsetHrs | read-write | mandatory | Offset hours for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.2.1.2 | ScalarwtWebioEA6x6TzOffsetMin | read-write | mandatory | Offset minutes for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.2.1.3 | ScalarwtWebioEA6x6TzEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Timezone |
| 1.3.6.1.4.1.5040.1.2.24.3.1.2.1.4 | ScalarwtWebioEA6x6StTzOffsetHrs | read-write | mandatory | Offset hours of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.2.1.5 | ScalarwtWebioEA6x6StTzOffsetMin | read-write | mandatory | Offset minutes of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.2.1.6 | ScalarwtWebioEA6x6StTzEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Summertime |
| 1.3.6.1.4.1.5040.1.2.24.3.1.2.1.7 | ScalarwtWebioEA6x6StTzStartMonth | read-write | mandatory | Month in which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.2.1.8 | ScalarwtWebioEA6x6StTzStartMode | read-write | mandatory | Mode of the day of the week for which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.2.1.9 | ScalarwtWebioEA6x6StTzStartWday | read-write | mandatory | Day of the week on which the change is made from winter time to summer time |
| 1.3.6.1.4.1.5040.1.2.24.3.1.2.1.10 | ScalarwtWebioEA6x6StTzStartHrs | read-write | mandatory | Hour in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.2.1.11 | ScalarwtWebioEA6x6StTzStartMin | read-write | mandatory | Minute in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.2.1.12 | ScalarwtWebioEA6x6StTzStopMonth | read-write | mandatory | Month in which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.2.1.13 | ScalarwtWebioEA6x6StTzStopMode | read-write | mandatory | Mode of the week day on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.2.1.14 | ScalarwtWebioEA6x6StTzStopWday | read-write | mandatory | Day of the week on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.2.1.15 | ScalarwtWebioEA6x6StTzStopHrs | read-write | mandatory | Hour at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.2.1.16 | ScalarwtWebioEA6x6StTzStopMin | read-write | mandatory | Minute at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.2.2 | NodewtWebioEA6x6TimeServer | |||
| 1.3.6.1.4.1.5040.1.2.24.3.1.2.2.1 | ScalarwtWebioEA6x6TimeServer1 | read-write | mandatory | IP address or name of the 1st time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.24.3.1.2.2.2 | ScalarwtWebioEA6x6TimeServer2 | read-write | mandatory | IP address or name of the 2nd time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.24.3.1.2.2.3 | ScalarwtWebioEA6x6TsEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Time Server |
| 1.3.6.1.4.1.5040.1.2.24.3.1.2.2.4 | ScalarwtWebioEA6x6TsSyncTime | read-write | mandatory | Daily synchronisation time with the time server (hour: 0-23). |
| 1.3.6.1.4.1.5040.1.2.24.3.1.2.3 | NodewtWebioEA6x6DeviceClock | |||
| 1.3.6.1.4.1.5040.1.2.24.3.1.2.3.1 | ScalarwtWebioEA6x6ClockHrs | read-write | mandatory | Clock hours taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.2.3.2 | ScalarwtWebioEA6x6ClockMin | read-write | mandatory | Clock minutes taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.2.3.3 | ScalarwtWebioEA6x6ClockDay | read-write | mandatory | Date: Day of the month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.2.3.4 | ScalarwtWebioEA6x6ClockMonth | read-write | mandatory | Date: Month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.2.3.5 | ScalarwtWebioEA6x6ClockYear | read-write | mandatory | Date: Year, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3 | NodewtWebioEA6x6Basic | |||
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.1 | NodewtWebioEA6x6Network | |||
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.1.1 | ScalarwtWebioEA6x6IpAddress | read-write | mandatory | IP address of the Webio |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.1.2 | ScalarwtWebioEA6x6SubnetMask | read-write | mandatory | Subnet mask of the Webio |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.1.3 | ScalarwtWebioEA6x6Gateway | read-write | mandatory | Gateway of the Webio |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.1.4 | ScalarwtWebioEA6x6DnsServer1 | read-write | mandatory | IP address of the 1st DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.1.5 | ScalarwtWebioEA6x6DnsServer2 | read-write | mandatory | IP address of the 2nd DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.1.6 | ScalarwtWebioEA6x6AddConfig | read-write | mandatory | Additional configuration (1=ON): Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1: DHCP enable Bit 0: BOOTP enable |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.2 | NodewtWebioEA6x6HTTP | |||
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.2.1 | ScalarwtWebioEA6x6Startup | read-write | mandatory | Binary coded start page, more than one page must not be selected: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 2: user.htm Bit 1: home.htm Bit … |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.2.2 | ScalarwtWebioEA6x6GetHeaderEnable | read-write | mandatory | If bits are set, every answer of a short form GET question will be lead by the IP-address and name of the device (Header) or a HTTP header (HTTP): Octet 1: unu… |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.2.3 | ScalarwtWebioEA6x6HttpInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.2.4 | ScalarwtWebioEA6x6HttpPort | read-write | mandatory | Definition of the standard HTML port (Default: 80). |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.3 | NodewtWebioEA6x6Mail | |||
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.3.1 | ScalarwtWebioEA6x6MailAdName | read-write | mandatory | Device name for mail administration. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.3.2 | ScalarwtWebioEA6x6MailReply | read-write | mandatory | Reply address for the mail server. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.3.3 | ScalarwtWebioEA6x6MailServer | read-write | mandatory | Name or IP address of the mail server. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.3.4 | ScalarwtWebioEA6x6MailEnable | read-write | mandatory | Set this bit to enable the sending of mails: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Mail enable |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.3.5 | ScalarwtWebioEA6x6MailAuthentication | read-write | mandatory | Selection of the authentication modi: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTE… |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.3.6 | ScalarwtWebioEA6x6MailAuthUser | read-write | mandatory | Name of the user to be authenticated. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.3.7 | ScalarwtWebioEA6x6MailAuthPassword | read-write | mandatory | Authentication password. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.3.8 | ScalarwtWebioEA6x6MailPop3Server | read-write | mandatory | Name or Ip-address of the POP3 Servers. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.4 | NodewtWebioEA6x6SNMP | |||
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.4.1 | ScalarwtWebioEA6x6SnmpEnable | read-write | mandatory | Set bit 0 to enable SNMP. If disabled, the device did not respond to any SNMP requests. Bit 1 decided wether the community string of read operations is compare… |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.4.2 | ScalarwtWebioEA6x6SnmpCommunityStringRead | read-write | mandatory | Community string read only |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.4.3 | ScalarwtWebioEA6x6SnmpCommunityStringReadWrite | read-write | mandatory | Community string read / write |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.4.4 | ScalarwtWebioEA6x6SnmpSystemTrapManagerIP | read-write | mandatory | Name or IP address of the TCP server which accepts the system trap. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.4.5 | ScalarwtWebioEA6x6SnmpSystemTrapEnable | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2: Diag messages Bit 3-7: unused |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.5 | NodewtWebioEA6x6UDP | |||
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.5.1 | ScalarwtWebioEA6x6UdpAdminPort | read-write | mandatory | Udp port to which the Udp queries ( short form GET requests) can be sent. This port number must be unique within the device. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.5.2 | ScalarwtWebioEA6x6UdpEnable | read-write | mandatory | Set this bit to enable UDP support: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : UDP enable |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.5.3 | ScalarwtWebioEA6x6UdpRemotePort | read-write | mandatory | Udp remote port setting. If this value is set to zero, the source port read from a request will be used as destination port for the answer. A non zero value fo… |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.6 | NodewtWebioEA6x6Binary | |||
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.6.1 | ScalarwtWebioEA6x6BinaryModeCount | read-only | mandatory | Number of independent binary channels. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.6.2 | TablewtWebioEA6x6BinaryIfTable | not-accessible | mandatory | Table of indices. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.6.2.1 | RowwtWebioEA6x6BinaryIfEntry | not-accessible | mandatory | Indices of the binary channels. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.6.2.1.1 | ColumnwtWebioEA6x6BinaryModeNo | read-only | mandatory | Number of the binary channel. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.6.3 | TablewtWebioEA6x6BinaryTable | not-accessible | mandatory | Table of properties of the binary mode. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.6.3.1 | RowwtWebioEA6x6BinaryEntry | not-accessible | mandatory | Binary properties. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.6.3.1.1 | ColumnwtWebioEA6x6BinaryOperationMode | read-write | mandatory | Selection of the operation mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: … |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.6.3.1.2 | ColumnwtWebioEA6x6BinaryTcpServerLocalPort | read-write | mandatory | Local TCP port for data exchange in this server mode. This port number must be unique within the device. Reserved port number must not be used (refere to the m… |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.6.3.1.3 | ColumnwtWebioEA6x6BinaryTcpServerInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.6.3.1.4 | ColumnwtWebioEA6x6BinaryTcpServerApplicationMode | read-write | mandatory | Selection of the application mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4… |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.6.3.1.5 | ColumnwtWebioEA6x6BinaryTcpClientLocalPort | read-write | mandatory | Local TCP port for data exchange in this client mode. This port number must be unique within the device. Reserved port number must not be used (refere to the m… |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.6.3.1.6 | ColumnwtWebioEA6x6BinaryTcpClientServerPort | read-write | mandatory | Port number of the server. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when setting t… |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.6.3.1.7 | ColumnwtWebioEA6x6BinaryTcpClientServerIpAddr | read-write | mandatory | Ip address of the server. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when setting th… |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.6.3.1.8 | ColumnwtWebioEA6x6BinaryTcpClientServerPassword | read-write | mandatory | Building a connection may be protected by the administrator password of the server. Enter the server password to establish the connection, if a server administ… |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.6.3.1.9 | ColumnwtWebioEA6x6BinaryTcpClientInactivity | read-write | mandatory | Connection timeout in 100ms. If no data are exchanged within the specified time, the device closes the connection to the server. The value 0 deactivates the ti… |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.6.3.1.10 | ColumnwtWebioEA6x6BinaryTcpClientInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.6.3.1.11 | ColumnwtWebioEA6x6BinaryTcpClientInterval | read-write | mandatory | Configurable interval with a 100ms base, in which the Webio device sends data to the configured application. A interval of zero stopps the periodical sending. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.6.3.1.12 | ColumnwtWebioEA6x6BinaryTcpClientApplicationMode | read-write | mandatory | Selection of the application mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4… |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.6.3.1.13 | ColumnwtWebioEA6x6BinaryUdpPeerLocalPort | read-write | mandatory | Local UDP port for data exchange in this peer to peer mode. This port number must be unique within the device. Reserved port number must not be used (refere to… |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.6.3.1.14 | ColumnwtWebioEA6x6BinaryUdpPeerRemotePort | read-write | mandatory | Port number of the remote device. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when se… |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.6.3.1.15 | ColumnwtWebioEA6x6BinaryUdpPeerRemoteIpAddr | read-write | mandatory | Ip address of the remote device. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when set… |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.6.3.1.16 | ColumnwtWebioEA6x6BinaryUdpPeerInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.6.3.1.17 | ColumnwtWebioEA6x6BinaryUdpPeerInterval | read-write | mandatory | Configurable interval with a 100ms base, in which the Webio device sends data to the configured remote device. A interval of zero stopps the periodical sending. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.6.3.1.18 | ColumnwtWebioEA6x6BinaryUdpPeerApplicationMode | read-write | mandatory | Selection of the application mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4… |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.6.3.1.19 | ColumnwtWebioEA6x6BinaryConnectedPort | read-only | mandatory | Port number of the remote device, after connection has been established. In case of no connection or missing port informations a zero will be read. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.6.3.1.20 | ColumnwtWebioEA6x6BinaryConnectedIpAddr | read-only | mandatory | IP address of the remote device, after connection has been established. In case of no connection or missing port informations 0.0.0.0 will be read. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.6.3.1.21 | ColumnwtWebioEA6x6BinaryTcpServerClientHttpPort | read-write | mandatory | HTTP port number of the remote device at TCP Server Mode. If an mailfunction occurs status informations will be send to this port. Not used at mode Compatible … |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.6.3.1.22 | ColumnwtWebioEA6x6BinaryTcpClientServerHttpPort | read-write | mandatory | HTTP port number of the remote device at TCP Client Mode. In the operating mode Box2Box connection status informations will be exchanged through this port. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.7 | NodewtWebioEA6x6Syslog | |||
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.7.1 | ScalarwtWebioEA6x6SyslogServerIP | read-write | mandatory | Name or IP address of the Syslog server, which accepts the Syslog messgaes. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.7.2 | ScalarwtWebioEA6x6SyslogServerPort | read-write | mandatory | Portnumber of the Syslog servers, default 514. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.7.3 | ScalarwtWebioEA6x6SyslogSystemMessagesEnable | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2: Diag Messages Bit 3-7: unused |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.7.4 | ScalarwtWebioEA6x6SyslogEnable | read-write | mandatory | Set bit 0to enable Syslog: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Syslog enable |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.8 | NodewtWebioEA6x6FTP | |||
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.8.1 | ScalarwtWebioEA6x6FTPServerIP | read-write | mandatory | Name or IP address of the FTP server, which accepts the FTP messages. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.8.2 | ScalarwtWebioEA6x6FTPServerControlPort | read-write | mandatory | Portnumber of the control port of the FTP server, default 21. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.8.3 | ScalarwtWebioEA6x6FTPUserName | read-write | mandatory | FTP Loggin: user name. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.8.4 | ScalarwtWebioEA6x6FTPPassword | read-write | mandatory | FTP Loggin: user password. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.8.5 | ScalarwtWebioEA6x6FTPAccount | read-write | mandatory | FTP Loggin: name of account. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.8.6 | ScalarwtWebioEA6x6FTPOption | read-write | mandatory | Bit 0 switches the FTP Server in Passiv-Mode, the Client controls the data connection on its own: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit … |
| 1.3.6.1.4.1.5040.1.2.24.3.1.3.8.7 | ScalarwtWebioEA6x6FTPEnable | read-write | mandatory | Set Bit 0 to enable FTP: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : FTP enable |
| 1.3.6.1.4.1.5040.1.2.24.3.1.4 | NodewtWebioEA6x6OutputMode | |||
| 1.3.6.1.4.1.5040.1.2.24.3.1.4.1 | TablewtWebioEA6x6OutputModeTable | not-accessible | mandatory | Table of output mode configurations dependent on the output indices. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.4.1.1 | RowwtWebioEA6x6OutputModeEntry | not-accessible | mandatory | Output mode configurations of the individual outputs. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.4.1.1.1 | ColumnwtWebioEA6x6OutputModeBit | read-write | mandatory | This binary coded output mode defines the individual operation mode for any output. More than one mode must not be selected. The OCTETS are interpreted bit-by-… |
| 1.3.6.1.4.1.5040.1.2.24.3.1.4.2 | ScalarwtWebioEA6x6SafetyTimeout | read-write | mandatory | After this period of time (multiple of 100ms) without receiving data outputs switch to their Safety States. For each output a independend safety state could be… |
| 1.3.6.1.4.1.5040.1.2.24.3.1.5 | NodewtWebioEA6x6Alarm | |||
| 1.3.6.1.4.1.5040.1.2.24.3.1.5.1 | ScalarwtWebioEA6x6AlarmCount | read-only | mandatory | Number of independent alarms. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.5.2 | TablewtWebioEA6x6AlarmIfTable | not-accessible | mandatory | List of alarm indices. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.5.2.1 | RowwtWebioEA6x6AlarmIfEntry | not-accessible | mandatory | Numbers of the alarms. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.5.2.1.1 | ColumnwtWebioEA6x6AlarmNo | read-only | mandatory | Numbers of the alarms. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.5.3 | TablewtWebioEA6x6AlarmTable | not-accessible | mandatory | List of settings depending on the alarm number. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.5.3.1 | RowwtWebioEA6x6AlarmEntry | not-accessible | mandatory | Alarm parameters of the individual alarms. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.5.3.1.1 | ColumnwtWebioEA6x6AlarmInputTrigger | read-write | mandatory | This variable allows setting of individual input trigger conditions. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an input. Bit 0 corr… |
| 1.3.6.1.4.1.5040.1.2.24.3.1.5.3.1.2 | ColumnwtWebioEA6x6AlarmOutputTrigger | read-write | mandatory | This variable allows setting of individual output trigger conditions. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 co… |
| 1.3.6.1.4.1.5040.1.2.24.3.1.5.3.1.3 | ColumnwtWebioEA6x6AlarmSystemTrigger | read-write | mandatory | Binary coded trigger conditions: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, … |
| 1.3.6.1.4.1.5040.1.2.24.3.1.5.3.1.4 | ColumnwtWebioEA6x6AlarmMaxCounterValue | read-write | mandatory | This variable configures a max. counter value. If an input counter value exceeds this max. value, the corresponding alarm is triggered. Input counters with its… |
| 1.3.6.1.4.1.5040.1.2.24.3.1.5.3.1.5 | ColumnwtWebioEA6x6AlarmInterval | read-write | mandatory | Send interval for alarm messages. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.5.3.1.6 | ColumnwtWebioEA6x6AlarmEnable | read-write | mandatory | Binary coded alarm enable: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Mail Enable Bit 1: SNMP Trap enable Bit 2: UDP enable Bit 3: Send in… |
| 1.3.6.1.4.1.5040.1.2.24.3.1.5.3.1.7 | ColumnwtWebioEA6x6AlarmMailAddr | read-write | mandatory | E-Mail address for sending the alarm mail to. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.5.3.1.8 | ColumnwtWebioEA6x6AlarmMailSubject | read-write | mandatory | Subject line for alarm mail. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.5.3.1.9 | ColumnwtWebioEA6x6AlarmMailText | read-write | mandatory | Alarm mail text: States of the Webio device can be included by using special tags. Please refer to the respective Webio manual |
| 1.3.6.1.4.1.5040.1.2.24.3.1.5.3.1.10 | ColumnwtWebioEA6x6AlarmSnmpManagerIP | read-write | mandatory | IP address of the SNMP Manager to which the Webio device should send SNMP traps. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.5.3.1.11 | ColumnwtWebioEA6x6AlarmSnmpTrapText | read-write | mandatory | This text appears in the trap body. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.5.3.1.12 | ColumnwtWebioEA6x6AlarmUdpIpAddr | read-write | mandatory | IP address of the UDP listener to which the Webio device should send UDP traps. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.5.3.1.13 | ColumnwtWebioEA6x6AlarmUdpPort | read-write | mandatory | Port number of the UDP listener to which the Webio device should send UDP traps. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.5.3.1.14 | ColumnwtWebioEA6x6AlarmUdpText | read-write | mandatory | This text appears in the UDP trap body. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.5.3.1.15 | ColumnwtWebioEA6x6AlarmTcpIpAddr | read-write | mandatory | IP address of the TCP listener to which the Webio device should send TCP traps. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.5.3.1.16 | ColumnwtWebioEA6x6AlarmTcpPort | read-write | mandatory | Port number of the TCP listener to which the Webio device should send TCP traps. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.5.3.1.17 | ColumnwtWebioEA6x6AlarmTcpText | read-write | mandatory | This text appears in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.5.3.1.18 | ColumnwtWebioEA6x6AlarmSyslogIpAddr | read-write | mandatory | IP address of the syslog server to which the Webio device should send syslog messages. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.5.3.1.19 | ColumnwtWebioEA6x6AlarmSyslogPort | read-write | mandatory | Port number of the syslog server to which the Webio device should send syslog messages. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.5.3.1.20 | ColumnwtWebioEA6x6AlarmSyslogText | read-write | mandatory | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.5.3.1.21 | ColumnwtWebioEA6x6AlarmFtpDataPort | read-write | mandatory | Local data port: 1..65535 or AUTO: the next free port will be assigned. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.5.3.1.22 | ColumnwtWebioEA6x6AlarmFtpFileName | read-write | mandatory | Name of the file including path informations. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.5.3.1.23 | ColumnwtWebioEA6x6AlarmFtpText | read-write | mandatory | Message text to store on the FTP server. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.5.3.1.24 | ColumnwtWebioEA6x6AlarmFtpOption | read-write | mandatory | Binary coded options, select only one option at the same time: STORE = replace file APPEND = append message at the end of the file Octet 1: unused Octet 2: unu… |
| 1.3.6.1.4.1.5040.1.2.24.3.1.5.3.1.25 | ColumnwtWebioEA6x6AlarmTimerCron | read-write | mandatory | This entry contains 5 space or tab seperated text fields for time trigger definition. Each field must match with the actual time to trigger a message, weekday … |
| 1.3.6.1.4.1.5040.1.2.24.3.1.5.3.1.26 | ColumnwtWebioEA6x6AlarmMailReleaseSubject | read-write | mandatory | Subject line for alarm mail. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.5.3.1.27 | ColumnwtWebioEA6x6AlarmMailReleaseText | read-write | mandatory | Release Alarm mail text: States of the Webio device can be included by using special tags. Please refer to the respective Webio manual |
| 1.3.6.1.4.1.5040.1.2.24.3.1.5.3.1.28 | ColumnwtWebioEA6x6AlarmSnmpTrapReleaseText | read-write | mandatory | This text appears in the trap body. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.5.3.1.29 | ColumnwtWebioEA6x6AlarmUdpReleaseText | read-write | mandatory | This text appears in the UDP trap body. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.5.3.1.30 | ColumnwtWebioEA6x6AlarmTcpReleaseText | read-write | mandatory | This text appears in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.5.3.1.31 | ColumnwtWebioEA6x6AlarmSyslogReleaseText | read-write | mandatory | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body. |
| 1.3.6.1.4.1.5040.1.2.24.3.1.5.3.1.32 | ColumnwtWebioEA6x6AlarmFtpReleaseText | read-write | mandatory | Message text to store on the FTP server. |
| 1.3.6.1.4.1.5040.1.2.24.3.2 | NodewtWebioEA6x6Ports | |||
| 1.3.6.1.4.1.5040.1.2.24.3.2.1 | TablewtWebioEA6x6InputPortTable | not-accessible | mandatory | List of settings depending on the input number. |
| 1.3.6.1.4.1.5040.1.2.24.3.2.1.1 | RowwtWebioEA6x6InputPortEntry | not-accessible | mandatory | Input parameter for the individual inputs. |
| 1.3.6.1.4.1.5040.1.2.24.3.2.1.1.1 | ColumnwtWebioEA6x6PortInputName | read-write | mandatory | Name of the input. |
| 1.3.6.1.4.1.5040.1.2.24.3.2.1.1.2 | ColumnwtWebioEA6x6PortInputText | read-write | mandatory | Description of the input. |
| 1.3.6.1.4.1.5040.1.2.24.3.2.1.1.3 | ColumnwtWebioEA6x6PortInputMode | read-write | mandatory | Binary coded modes: Selecting short pulse detection enable by setting the corresponding bit to 1 enables interrupt support for counting. Only positive edges ar… |
| 1.3.6.1.4.1.5040.1.2.24.3.2.1.1.4 | ColumnwtWebioEA6x6PortInputFilter | read-write | mandatory | Pulses with a duration shorter than here specified (duration in 1/1000 sec), are ignored. |
| 1.3.6.1.4.1.5040.1.2.24.3.2.1.1.5 | ColumnwtWebioEA6x6PortInputBicountPulsePolarity | read-write | mandatory | This value defines the polarity of the input pulse. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 0 : negative polarity Bit 1 : positive polarit… |
| 1.3.6.1.4.1.5040.1.2.24.3.2.1.1.6 | ColumnwtWebioEA6x6PortInputBicountInactivTimeout | read-write | mandatory | Pulse chains with a duration shorter than here specified (in 1/10 sek), are ignored. |
| 1.3.6.1.4.1.5040.1.2.24.3.2.2 | TablewtWebioEA6x6OutputPortTable | not-accessible | mandatory | List of settings depending on the output number. |
| 1.3.6.1.4.1.5040.1.2.24.3.2.2.1 | RowwtWebioEA6x6OutputPortEntry | not-accessible | mandatory | Output parameters of the individual outputs. |
| 1.3.6.1.4.1.5040.1.2.24.3.2.2.1.1 | ColumnwtWebioEA6x6PortOutputName | read-write | mandatory | Name of the output. |
| 1.3.6.1.4.1.5040.1.2.24.3.2.2.1.2 | ColumnwtWebioEA6x6PortOutputText | read-write | mandatory | Description of the output. |
| 1.3.6.1.4.1.5040.1.2.24.3.2.2.1.3 | ColumnwtWebioEA6x6PortOutputGroupMode | read-write | mandatory | It is possible to connect outputs together to increase the output current. This could be done by connecting 2 or 4 outputs in a group together. All bits of suc… |
| 1.3.6.1.4.1.5040.1.2.24.3.2.2.1.4 | ColumnwtWebioEA6x6PortOutputSafetyState | read-write | mandatory | This variable allows setting of individual digital outputs. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds … |
| 1.3.6.1.4.1.5040.1.2.24.3.2.2.1.5 | ColumnwtWebioEA6x6PortLogicInputMask | read-write | mandatory | Selecting one of these inputs by setting the corresponding bit to 1 enables the logic function for the output identified by the index within this table. The ca… |
| 1.3.6.1.4.1.5040.1.2.24.3.2.2.1.6 | ColumnwtWebioEA6x6PortLogicInputInverter | read-write | mandatory | Every input bit selected here will be inverted. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 0-5 : inputs 0-5 Bit 6-7 : unused |
| 1.3.6.1.4.1.5040.1.2.24.3.2.2.1.7 | ColumnwtWebioEA6x6PortLogicFunction | read-write | mandatory | This determines the logic function. No more than one function may be selected. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 0 : logic function … |
| 1.3.6.1.4.1.5040.1.2.24.3.2.2.1.8 | ColumnwtWebioEA6x6PortLogicOutputInverter | read-write | mandatory | The logical operation result could be inverteted by setting the corresponding bit to 1. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 0 : Output… |
| 1.3.6.1.4.1.5040.1.2.24.3.2.2.1.9 | ColumnwtWebioEA6x6PortPulseDuration | read-write | mandatory | Pulse length in 1/1000 sec. Setting this value to zero, disables the pulse output. |
| 1.3.6.1.4.1.5040.1.2.24.3.2.2.1.10 | ColumnwtWebioEA6x6PortPulsePolarity | read-write | mandatory | This value defines the polarity of the output pulse, if wtWebioEA6x6PortPulseDuration is not set to zero. After the pulse is finished, the output switches back… |
| 1.3.6.1.4.1.5040.1.2.24.3.3 | NodewtWebioEA6x6Manufact | |||
| 1.3.6.1.4.1.5040.1.2.24.3.3.1 | ScalarwtWebioEA6x6MfName | read-write | mandatory | Manufacturer company name |
| 1.3.6.1.4.1.5040.1.2.24.3.3.2 | ScalarwtWebioEA6x6MfAddr | read-write | mandatory | Manufacturer address. |
| 1.3.6.1.4.1.5040.1.2.24.3.3.3 | ScalarwtWebioEA6x6MfHotline | read-write | mandatory | Manufacturer hotline. |
| 1.3.6.1.4.1.5040.1.2.24.3.3.4 | ScalarwtWebioEA6x6MfInternet | read-write | mandatory | Manufacturer Internet address. |
| 1.3.6.1.4.1.5040.1.2.24.3.3.5 | ScalarwtWebioEA6x6MfDeviceTyp | read-write | mandatory | Manufacturer device name (model number). |
| 1.3.6.1.4.1.5040.1.2.24.4 | NodewtWebioEA6x6Diag | |||
| 1.3.6.1.4.1.5040.1.2.24.4.1 | ScalarwtWebioEA6x6DiagErrorCount | read-only | mandatory | Number of entries in the error memory. |
| 1.3.6.1.4.1.5040.1.2.24.4.2 | ScalarwtWebioEA6x6DiagBinaryError | read-only | mandatory | Error causes coded bit-by-bit. |
| 1.3.6.1.4.1.5040.1.2.24.4.3 | ScalarwtWebioEA6x6DiagErrorIndex | read-write | mandatory | The value of this variable is used as an index to read an error massege from wtWebioEA6x6DiagErrorMessage. Errors are numbered from 1 to wtWebioEA6x6DiagErrorC… |
| 1.3.6.1.4.1.5040.1.2.24.4.4 | ScalarwtWebioEA6x6DiagErrorMessage | read-only | mandatory | Using wtWebioEA6x6DiagErrorIndex as an index, the appropriate message is available. |
| 1.3.6.1.4.1.5040.1.2.24.4.5 | ScalarwtWebioEA6x6DiagErrorClear | write-only | mandatory | Writing 1 into this variable clears all diagnosis messages. |
| 1.3.6.1.4.1.5040.1.2.24.41 | NodewtWebioEA6x6Alert1 | This SNMP trap is generated when Alarm 1 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.24.42 | NodewtWebioEA6x6Alert2 | This SNMP trap is generated when Alarm 2 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.24.43 | NodewtWebioEA6x6Alert3 | This SNMP trap is generated when Alarm 3 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.24.44 | NodewtWebioEA6x6Alert4 | This SNMP trap is generated when Alarm 4 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.24.45 | NodewtWebioEA6x6Alert5 | This SNMP trap is generated when Alarm 5 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.24.46 | NodewtWebioEA6x6Alert6 | This SNMP trap is generated when Alarm 6 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.24.47 | NodewtWebioEA6x6Alert7 | This SNMP trap is generated when Alarm 7 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.24.48 | NodewtWebioEA6x6Alert8 | This SNMP trap is generated when Alarm 8 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.24.49 | NodewtWebioEA6x6Alert9 | This SNMP trap is generated when Alarm 9 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.24.50 | NodewtWebioEA6x6Alert10 | This SNMP trap is generated when Alarm 10 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.24.51 | NodewtWebioEA6x6Alert11 | This SNMP trap is generated when Alarm 11 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.24.52 | NodewtWebioEA6x6Alert12 | This SNMP trap is generated when Alarm 12 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.24.71 | NodewtWebioEA6x6Alert13 | This SNMP trap is generated when Alarm 1 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.24.72 | NodewtWebioEA6x6Alert14 | This SNMP trap is generated when Alarm 2 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.24.73 | NodewtWebioEA6x6Alert15 | This SNMP trap is generated when Alarm 3 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.24.74 | NodewtWebioEA6x6Alert16 | This SNMP trap is generated when Alarm 4 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.24.75 | NodewtWebioEA6x6Alert17 | This SNMP trap is generated when Alarm 5 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.24.76 | NodewtWebioEA6x6Alert18 | This SNMP trap is generated when Alarm 6 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.24.77 | NodewtWebioEA6x6Alert19 | This SNMP trap is generated when Alarm 7 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.24.78 | NodewtWebioEA6x6Alert20 | This SNMP trap is generated when Alarm 8 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.24.79 | NodewtWebioEA6x6Alert21 | This SNMP trap is generated when Alarm 9 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.24.80 | NodewtWebioEA6x6Alert22 | This SNMP trap is generated when Alarm 10 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.24.81 | NodewtWebioEA6x6Alert23 | This SNMP trap is generated when Alarm 11 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.24.82 | NodewtWebioEA6x6Alert24 | This SNMP trap is generated when Alarm 12 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.24.110 | NodewtWebioEA6x6AlertDiag | This SNMP trap is generated when a diagnosis/error message was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.25 | NodewtWebioEA2x2ERP | |||
| 1.3.6.1.4.1.5040.1.2.25.1 | NodewtWebioEA2x2ERPInOut | |||
| 1.3.6.1.4.1.5040.1.2.25.1.1 | ScalarwtWebioEA2x2ERPInputs | read-only | mandatory | Number of idependent inputs. |
| 1.3.6.1.4.1.5040.1.2.25.1.2 | ScalarwtWebioEA2x2ERPOutputs | read-only | mandatory | Number of idependent outputs. |
| 1.3.6.1.4.1.5040.1.2.25.1.3 | TablewtWebioEA2x2ERPInputTable | not-accessible | mandatory | List of input indices. |
| 1.3.6.1.4.1.5040.1.2.25.1.3.1 | RowwtWebioEA2x2ERPInputEntry | not-accessible | mandatory | Number of the inputs. |
| 1.3.6.1.4.1.5040.1.2.25.1.3.1.1 | ColumnwtWebioEA2x2ERPInputNo | read-only | mandatory | Index numbers of the inputs. |
| 1.3.6.1.4.1.5040.1.2.25.1.3.1.2 | ColumnwtWebioEA2x2ERPInputCounter | read-only | mandatory | Value of the input counter. |
| 1.3.6.1.4.1.5040.1.2.25.1.3.1.3 | ColumnwtWebioEA2x2ERPInputCounterClear | read-only | mandatory | Clears the input counter after returning its value. |
| 1.3.6.1.4.1.5040.1.2.25.1.3.1.4 | ColumnwtWebioEA2x2ERPInputState | read-only | mandatory | Value of a single input bit, 0-OFF, 1-ON. |
| 1.3.6.1.4.1.5040.1.2.25.1.4 | ScalarwtWebioEA2x2ERPInputValue | read-only | mandatory | This variable is used to read the inputs of the digital I/O port. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corres… |
| 1.3.6.1.4.1.5040.1.2.25.1.5 | TablewtWebioEA2x2ERPOutputTable | not-accessible | mandatory | List of output indices. |
| 1.3.6.1.4.1.5040.1.2.25.1.5.1 | RowwtWebioEA2x2ERPOutputEntry | not-accessible | mandatory | Number of the outputs. |
| 1.3.6.1.4.1.5040.1.2.25.1.5.1.1 | ColumnwtWebioEA2x2ERPOutputNo | read-only | mandatory | Output number. |
| 1.3.6.1.4.1.5040.1.2.25.1.5.1.2 | ColumnwtWebioEA2x2ERPOutputState | read-write | mandatory | Value of a single output bit, 0-OFF, 1-ON. |
| 1.3.6.1.4.1.5040.1.2.25.1.6 | ScalarwtWebioEA2x2ERPOutputValue | read-write | mandatory | This variable is used to read and write the outputs of the digital I/O port. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. B… |
| 1.3.6.1.4.1.5040.1.2.25.1.7 | ScalarwtWebioEA2x2ERPSetOutput | read-write | mandatory | This variable allows setting of individual digital outputs. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds … |
| 1.3.6.1.4.1.5040.1.2.25.2 | NodewtWebioEA2x2ERPSessCntrl | |||
| 1.3.6.1.4.1.5040.1.2.25.2.1 | ScalarwtWebioEA2x2ERPSessCntrlPassword | read-write | mandatory | Entering this password opens a session which is ended by writing a 1 to wtWebioEA2x2ERPSessCntrlLogout. When read this variable provides a string of length zer… |
| 1.3.6.1.4.1.5040.1.2.25.2.2 | ScalarwtWebioEA2x2ERPSessCntrlConfigMode | read-only | mandatory | When the device is in SNMP configuration mode, the value 1 is returned, otherwise 0. If the read value is 0 even though the password was written, the device is… |
| 1.3.6.1.4.1.5040.1.2.25.2.3 | ScalarwtWebioEA2x2ERPSessCntrlLogout | read-write | mandatory | If the device is in configuration mode and the session was opened by this SNMP Manager, writing a 1 to this variable will end the session and all parameters ar… |
| 1.3.6.1.4.1.5040.1.2.25.2.4 | ScalarwtWebioEA2x2ERPSessCntrlAdminPassword | read-write | mandatory | This password protects access to the variables with administrator rights. It can only be changed by the administrator. If no password was assigned, the valid p… |
| 1.3.6.1.4.1.5040.1.2.25.2.5 | ScalarwtWebioEA2x2ERPSessCntrlConfigPassword | read-write | mandatory | This password protects access to the variables with configurator rights. It can be changed by the administrator and by the configurator. If no password was ass… |
| 1.3.6.1.4.1.5040.1.2.25.3 | NodewtWebioEA2x2ERPConfig | |||
| 1.3.6.1.4.1.5040.1.2.25.3.1 | NodewtWebioEA2x2ERPDevice | |||
| 1.3.6.1.4.1.5040.1.2.25.3.1.1 | NodewtWebioEA2x2ERPText | |||
| 1.3.6.1.4.1.5040.1.2.25.3.1.1.1 | ScalarwtWebioEA2x2ERPDeviceName | read-write | mandatory | Name of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.1.2 | ScalarwtWebioEA2x2ERPDeviceText | read-write | mandatory | Description of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.1.3 | ScalarwtWebioEA2x2ERPDeviceLocation | read-write | mandatory | Description of the location of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.1.4 | ScalarwtWebioEA2x2ERPDeviceContact | read-write | mandatory | Contact address of the system operator of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.2 | NodewtWebioEA2x2ERPTimeDate | |||
| 1.3.6.1.4.1.5040.1.2.25.3.1.2.1 | NodewtWebioEA2x2ERPTimeZone | |||
| 1.3.6.1.4.1.5040.1.2.25.3.1.2.1.1 | ScalarwtWebioEA2x2ERPTzOffsetHrs | read-write | mandatory | Offset hours for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.2.1.2 | ScalarwtWebioEA2x2ERPTzOffsetMin | read-write | mandatory | Offset minutes for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.2.1.3 | ScalarwtWebioEA2x2ERPTzEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Timezone |
| 1.3.6.1.4.1.5040.1.2.25.3.1.2.1.4 | ScalarwtWebioEA2x2ERPStTzOffsetHrs | read-write | mandatory | Offset hours of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.2.1.5 | ScalarwtWebioEA2x2ERPStTzOffsetMin | read-write | mandatory | Offset minutes of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.2.1.6 | ScalarwtWebioEA2x2ERPStTzEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Summertime |
| 1.3.6.1.4.1.5040.1.2.25.3.1.2.1.7 | ScalarwtWebioEA2x2ERPStTzStartMonth | read-write | mandatory | Month in which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.2.1.8 | ScalarwtWebioEA2x2ERPStTzStartMode | read-write | mandatory | Mode of the day of the week for which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.2.1.9 | ScalarwtWebioEA2x2ERPStTzStartWday | read-write | mandatory | Day of the week on which the change is made from winter time to summer time |
| 1.3.6.1.4.1.5040.1.2.25.3.1.2.1.10 | ScalarwtWebioEA2x2ERPStTzStartHrs | read-write | mandatory | Hour in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.2.1.11 | ScalarwtWebioEA2x2ERPStTzStartMin | read-write | mandatory | Minute in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.2.1.12 | ScalarwtWebioEA2x2ERPStTzStopMonth | read-write | mandatory | Month in which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.2.1.13 | ScalarwtWebioEA2x2ERPStTzStopMode | read-write | mandatory | Mode of the week day on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.2.1.14 | ScalarwtWebioEA2x2ERPStTzStopWday | read-write | mandatory | Day of the week on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.2.1.15 | ScalarwtWebioEA2x2ERPStTzStopHrs | read-write | mandatory | Hour at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.2.1.16 | ScalarwtWebioEA2x2ERPStTzStopMin | read-write | mandatory | Minute at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.2.2 | NodewtWebioEA2x2ERPTimeServer | |||
| 1.3.6.1.4.1.5040.1.2.25.3.1.2.2.1 | ScalarwtWebioEA2x2ERPTimeServer1 | read-write | mandatory | IP address or name of the 1st time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.25.3.1.2.2.2 | ScalarwtWebioEA2x2ERPTimeServer2 | read-write | mandatory | IP address or name of the 2nd time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.25.3.1.2.2.3 | ScalarwtWebioEA2x2ERPTsEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Time Server |
| 1.3.6.1.4.1.5040.1.2.25.3.1.2.2.4 | ScalarwtWebioEA2x2ERPTsSyncTime | read-write | mandatory | Daily synchronisation time with the time server (hour: 0-23). |
| 1.3.6.1.4.1.5040.1.2.25.3.1.2.3 | NodewtWebioEA2x2ERPDeviceClock | |||
| 1.3.6.1.4.1.5040.1.2.25.3.1.2.3.1 | ScalarwtWebioEA2x2ERPClockHrs | read-write | mandatory | Clock hours taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.2.3.2 | ScalarwtWebioEA2x2ERPClockMin | read-write | mandatory | Clock minutes taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.2.3.3 | ScalarwtWebioEA2x2ERPClockDay | read-write | mandatory | Date: Day of the month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.2.3.4 | ScalarwtWebioEA2x2ERPClockMonth | read-write | mandatory | Date: Month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.2.3.5 | ScalarwtWebioEA2x2ERPClockYear | read-write | mandatory | Date: Year, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3 | NodewtWebioEA2x2ERPBasic | |||
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.1 | NodewtWebioEA2x2ERPNetwork | |||
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.1.1 | ScalarwtWebioEA2x2ERPIpAddress | read-write | mandatory | IP address of the Webio |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.1.2 | ScalarwtWebioEA2x2ERPSubnetMask | read-write | mandatory | Subnet mask of the Webio |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.1.3 | ScalarwtWebioEA2x2ERPGateway | read-write | mandatory | Gateway of the Webio |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.1.4 | ScalarwtWebioEA2x2ERPDnsServer1 | read-write | mandatory | IP address of the 1st DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.1.5 | ScalarwtWebioEA2x2ERPDnsServer2 | read-write | mandatory | IP address of the 2nd DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.1.6 | ScalarwtWebioEA2x2ERPAddConfig | read-write | mandatory | Additional configuration (1=ON): Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1: DHCP enable Bit 0: BOOTP enable |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.2 | NodewtWebioEA2x2ERPHTTP | |||
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.2.1 | ScalarwtWebioEA2x2ERPStartup | read-write | mandatory | Binary coded start page, more than one page must not be selected: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 2: user.htm Bit 1: home.htm Bit … |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.2.2 | ScalarwtWebioEA2x2ERPGetHeaderEnable | read-write | mandatory | If bits are set, every answer of a short form GET question will be lead by the IP-address and name of the device (Header) or a HTTP header (HTTP): Octet 1: unu… |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.2.3 | ScalarwtWebioEA2x2ERPHttpInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.2.4 | ScalarwtWebioEA2x2ERPHttpPort | read-write | mandatory | Definition of the standard HTML port (Default: 80). |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.3 | NodewtWebioEA2x2ERPMail | |||
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.3.1 | ScalarwtWebioEA2x2ERPMailAdName | read-write | mandatory | Device name for mail administration. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.3.2 | ScalarwtWebioEA2x2ERPMailReply | read-write | mandatory | Reply address for the mail server. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.3.3 | ScalarwtWebioEA2x2ERPMailServer | read-write | mandatory | Name or IP address of the mail server. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.3.4 | ScalarwtWebioEA2x2ERPMailEnable | read-write | mandatory | Set this bit to enable the sending of mails: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Mail enable |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.3.5 | ScalarwtWebioEA2x2ERPMailAuthentication | read-write | mandatory | Selection of the authentication modi: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTE… |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.3.6 | ScalarwtWebioEA2x2ERPMailAuthUser | read-write | mandatory | Name of the user to be authenticated. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.3.7 | ScalarwtWebioEA2x2ERPMailAuthPassword | read-write | mandatory | Authentication password. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.3.8 | ScalarwtWebioEA2x2ERPMailPop3Server | read-write | mandatory | Name or Ip-address of the POP3 Servers. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.4 | NodewtWebioEA2x2ERPSNMP | |||
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.4.1 | ScalarwtWebioEA2x2ERPSnmpEnable | read-write | mandatory | Set bit 0 to enable SNMP. If disabled, the device did not respond to any SNMP requests. Bit 1 decided wether the community string of read operations is compare… |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.4.2 | ScalarwtWebioEA2x2ERPSnmpCommunityStringRead | read-write | mandatory | Community string read only |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.4.3 | ScalarwtWebioEA2x2ERPSnmpCommunityStringReadWrite | read-write | mandatory | Community string read / write |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.4.4 | ScalarwtWebioEA2x2ERPSnmpSystemTrapManagerIP | read-write | mandatory | Name or IP address of the TCP server which accepts the system trap. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.4.5 | ScalarwtWebioEA2x2ERPSnmpSystemTrapEnable | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2: Diag messages Bit 3-7: unused |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.5 | NodewtWebioEA2x2ERPUDP | |||
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.5.1 | ScalarwtWebioEA2x2ERPUdpAdminPort | read-write | mandatory | Udp port to which the Udp queries ( short form GET requests) can be sent. This port number must be unique within the device. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.5.2 | ScalarwtWebioEA2x2ERPUdpEnable | read-write | mandatory | Set this bit to enable UDP support: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : UDP enable |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.5.3 | ScalarwtWebioEA2x2ERPUdpRemotePort | read-write | mandatory | Udp remote port setting. If this value is set to zero, the source port read from a request will be used as destination port for the answer. A non zero value fo… |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.6 | NodewtWebioEA2x2ERPBinary | |||
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.6.1 | ScalarwtWebioEA2x2ERPBinaryModeCount | read-only | mandatory | Number of independent binary channels. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.6.2 | TablewtWebioEA2x2ERPBinaryIfTable | not-accessible | mandatory | Table of indices. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.6.2.1 | RowwtWebioEA2x2ERPBinaryIfEntry | not-accessible | mandatory | Indices of the binary channels. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.6.2.1.1 | ColumnwtWebioEA2x2ERPBinaryModeNo | read-only | mandatory | Number of the binary channel. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.6.3 | TablewtWebioEA2x2ERPBinaryTable | not-accessible | mandatory | Table of properties of the binary mode. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.6.3.1 | RowwtWebioEA2x2ERPBinaryEntry | not-accessible | mandatory | Binary properties. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.6.3.1.1 | ColumnwtWebioEA2x2ERPBinaryOperationMode | read-write | mandatory | Selection of the operation mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: … |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.6.3.1.2 | ColumnwtWebioEA2x2ERPBinaryTcpServerLocalPort | read-write | mandatory | Local TCP port for data exchange in this server mode. This port number must be unique within the device. Reserved port number must not be used (refere to the m… |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.6.3.1.3 | ColumnwtWebioEA2x2ERPBinaryTcpServerInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.6.3.1.4 | ColumnwtWebioEA2x2ERPBinaryTcpServerApplicationMode | read-write | mandatory | Selection of the application mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4… |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.6.3.1.5 | ColumnwtWebioEA2x2ERPBinaryTcpClientLocalPort | read-write | mandatory | Local TCP port for data exchange in this client mode. This port number must be unique within the device. Reserved port number must not be used (refere to the m… |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.6.3.1.6 | ColumnwtWebioEA2x2ERPBinaryTcpClientServerPort | read-write | mandatory | Port number of the server. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when setting t… |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.6.3.1.7 | ColumnwtWebioEA2x2ERPBinaryTcpClientServerIpAddr | read-write | mandatory | Ip address of the server. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when setting th… |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.6.3.1.8 | ColumnwtWebioEA2x2ERPBinaryTcpClientServerPassword | read-write | mandatory | Building a connection may be protected by the administrator password of the server. Enter the server password to establish the connection, if a server administ… |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.6.3.1.9 | ColumnwtWebioEA2x2ERPBinaryTcpClientInactivity | read-write | mandatory | Connection timeout in 100ms. If no data are exchanged within the specified time, the device closes the connection to the server. The value 0 deactivates the ti… |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.6.3.1.10 | ColumnwtWebioEA2x2ERPBinaryTcpClientInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.6.3.1.11 | ColumnwtWebioEA2x2ERPBinaryTcpClientInterval | read-write | mandatory | Configurable interval with a 100ms base, in which the Webio device sends data to the configured application. A interval of zero stopps the periodical sending. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.6.3.1.12 | ColumnwtWebioEA2x2ERPBinaryTcpClientApplicationMode | read-write | mandatory | Selection of the application mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4… |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.6.3.1.13 | ColumnwtWebioEA2x2ERPBinaryUdpPeerLocalPort | read-write | mandatory | Local UDP port for data exchange in this peer to peer mode. This port number must be unique within the device. Reserved port number must not be used (refere to… |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.6.3.1.14 | ColumnwtWebioEA2x2ERPBinaryUdpPeerRemotePort | read-write | mandatory | Port number of the remote device. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when se… |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.6.3.1.15 | ColumnwtWebioEA2x2ERPBinaryUdpPeerRemoteIpAddr | read-write | mandatory | Ip address of the remote device. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when set… |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.6.3.1.16 | ColumnwtWebioEA2x2ERPBinaryUdpPeerInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.6.3.1.17 | ColumnwtWebioEA2x2ERPBinaryUdpPeerInterval | read-write | mandatory | Configurable interval with a 100ms base, in which the Webio device sends data to the configured remote device. A interval of zero stopps the periodical sending. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.6.3.1.18 | ColumnwtWebioEA2x2ERPBinaryUdpPeerApplicationMode | read-write | mandatory | Selection of the application mode: The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds to the LSB. OCTET 1: unus… |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.6.3.1.19 | ColumnwtWebioEA2x2ERPBinaryConnectedPort | read-only | mandatory | Port number of the remote device, after connection has been established. In case of no connection or missing port informations a zero will be read. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.6.3.1.20 | ColumnwtWebioEA2x2ERPBinaryConnectedIpAddr | read-only | mandatory | IP address of the remote device, after connection has been established. In case of no connection or missing port informations 0.0.0.0 will be read. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.6.3.1.21 | ColumnwtWebioEA2x2ERPBinaryTcpServerClientHttpPort | read-write | mandatory | HTTP port number of the remote device at TCP Server Mode. If an mailfunction occurs status informations will be send to this port. Not used at mode Compatible … |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.6.3.1.22 | ColumnwtWebioEA2x2ERPBinaryTcpClientServerHttpPort | read-write | mandatory | HTTP port number of the remote device at TCP Client Mode. In the operating mode Box2Box connection status informations will be exchanged through this port. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.7 | NodewtWebioEA2x2ERPSyslog | |||
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.7.1 | ScalarwtWebioEA2x2ERPSyslogServerIP | read-write | mandatory | Name or IP address of the Syslog server, which accepts the Syslog messgaes. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.7.2 | ScalarwtWebioEA2x2ERPSyslogServerPort | read-write | mandatory | Portnumber of the Syslog servers, default 514. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.7.3 | ScalarwtWebioEA2x2ERPSyslogSystemMessagesEnable | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2: Diag Messages Bit 3-7: unused |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.7.4 | ScalarwtWebioEA2x2ERPSyslogEnable | read-write | mandatory | Set bit 0to enable Syslog: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Syslog enable |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.8 | NodewtWebioEA2x2ERPFTP | |||
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.8.1 | ScalarwtWebioEA2x2ERPFTPServerIP | read-write | mandatory | Name or IP address of the FTP server, which accepts the FTP messages. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.8.2 | ScalarwtWebioEA2x2ERPFTPServerControlPort | read-write | mandatory | Portnumber of the control port of the FTP server, default 21. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.8.3 | ScalarwtWebioEA2x2ERPFTPUserName | read-write | mandatory | FTP Loggin: user name. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.8.4 | ScalarwtWebioEA2x2ERPFTPPassword | read-write | mandatory | FTP Loggin: user password. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.8.5 | ScalarwtWebioEA2x2ERPFTPAccount | read-write | mandatory | FTP Loggin: name of account. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.8.6 | ScalarwtWebioEA2x2ERPFTPOption | read-write | mandatory | Bit 0 switches the FTP Server in Passiv-Mode, the Client controls the data connection on its own: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit … |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.8.7 | ScalarwtWebioEA2x2ERPFTPEnable | read-write | mandatory | Set Bit 0 to enable FTP: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : FTP enable |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.10 | NodewtWebioEA2x2ERPWayBack | |||
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.10.1 | ScalarwtWebioEA2x2ERPWayBackEnable | read-write | mandatory | Set Bit 0 to enable WayBack: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : WayBack enable |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.10.2 | ScalarwtWebioEA2x2ERPWayBackServerControlPort | read-write | mandatory | Portnumber of the control port of the FTP server, default 21. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.10.3 | ScalarwtWebioEA2x2ERPWayBackFTPPassword | read-write | mandatory | WayBack FTP Loggin: Password of the user. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.10.4 | ScalarwtWebioEA2x2ERPWayBackFTPResponse | read-write | mandatory | WayBack FTP response: return message after login. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.3.10.5 | ScalarwtWebioEA2x2ERPWayBackFTPTimeOut | read-write | mandatory | WayBack FTP Timeout: a request must be finished within this periode of time. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.4 | NodewtWebioEA2x2ERPOutputMode | |||
| 1.3.6.1.4.1.5040.1.2.25.3.1.4.1 | TablewtWebioEA2x2ERPOutputModeTable | not-accessible | mandatory | Table of output mode configurations dependent on the output indices. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.4.1.1 | RowwtWebioEA2x2ERPOutputModeEntry | not-accessible | mandatory | Output mode configurations of the individual outputs. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.4.1.1.1 | ColumnwtWebioEA2x2ERPOutputModeBit | read-write | mandatory | This binary coded output mode defines the individual operation mode for any output. More than one mode must not be selected. The OCTETS are interpreted bit-by-… |
| 1.3.6.1.4.1.5040.1.2.25.3.1.4.2 | ScalarwtWebioEA2x2ERPSafetyTimeout | read-write | mandatory | After this period of time (multiple of 100ms) without receiving data outputs switch to their Safety States. For each output a independend safety state could be… |
| 1.3.6.1.4.1.5040.1.2.25.3.1.4.3 | ScalarwtWebioEA2x2ERPLoadControlEnable | read-write | mandatory | Here the function of automatic load control can be enabled. All output were tested in pairs (0-1). If an error occours at one output, both output of an pair wi… |
| 1.3.6.1.4.1.5040.1.2.25.3.1.5 | NodewtWebioEA2x2ERPAlarm | |||
| 1.3.6.1.4.1.5040.1.2.25.3.1.5.1 | ScalarwtWebioEA2x2ERPAlarmCount | read-only | mandatory | Number of independent alarms. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.5.2 | TablewtWebioEA2x2ERPAlarmIfTable | not-accessible | mandatory | List of alarm indices. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.5.2.1 | RowwtWebioEA2x2ERPAlarmIfEntry | not-accessible | mandatory | Numbers of the alarms. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.5.2.1.1 | ColumnwtWebioEA2x2ERPAlarmNo | read-only | mandatory | Numbers of the alarms. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.5.3 | TablewtWebioEA2x2ERPAlarmTable | not-accessible | mandatory | List of settings depending on the alarm number. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.5.3.1 | RowwtWebioEA2x2ERPAlarmEntry | not-accessible | mandatory | Alarm parameters of the individual alarms. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.5.3.1.1 | ColumnwtWebioEA2x2ERPAlarmInputTrigger | read-write | mandatory | This variable allows setting of individual input trigger conditions. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an input. Bit 0 corr… |
| 1.3.6.1.4.1.5040.1.2.25.3.1.5.3.1.2 | ColumnwtWebioEA2x2ERPAlarmOutputTrigger | read-write | mandatory | This variable allows setting of individual output trigger conditions. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 co… |
| 1.3.6.1.4.1.5040.1.2.25.3.1.5.3.1.3 | ColumnwtWebioEA2x2ERPAlarmSystemTrigger | read-write | mandatory | Binary coded trigger conditions: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, … |
| 1.3.6.1.4.1.5040.1.2.25.3.1.5.3.1.4 | ColumnwtWebioEA2x2ERPAlarmMaxCounterValue | read-write | mandatory | This variable configures a max. counter value. If an input counter value exceeds this max. value, the corresponding alarm is triggered. Input counters with its… |
| 1.3.6.1.4.1.5040.1.2.25.3.1.5.3.1.5 | ColumnwtWebioEA2x2ERPAlarmInterval | read-write | mandatory | Send interval for alarm messages. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.5.3.1.6 | ColumnwtWebioEA2x2ERPAlarmEnable | read-write | mandatory | Binary coded alarm enable: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Mail Enable Bit 1: SNMP Trap enable Bit 2: UDP enable Bit 3: Send in… |
| 1.3.6.1.4.1.5040.1.2.25.3.1.5.3.1.7 | ColumnwtWebioEA2x2ERPAlarmMailAddr | read-write | mandatory | E-Mail address for sending the alarm mail to. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.5.3.1.8 | ColumnwtWebioEA2x2ERPAlarmMailSubject | read-write | mandatory | Subject line for alarm mail. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.5.3.1.9 | ColumnwtWebioEA2x2ERPAlarmMailText | read-write | mandatory | Alarm mail text: States of the Webio device can be included by using special tags. Please refer to the respective Webio manual |
| 1.3.6.1.4.1.5040.1.2.25.3.1.5.3.1.10 | ColumnwtWebioEA2x2ERPAlarmSnmpManagerIP | read-write | mandatory | IP address of the SNMP Manager to which the Webio device should send SNMP traps. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.5.3.1.11 | ColumnwtWebioEA2x2ERPAlarmSnmpTrapText | read-write | mandatory | This text appears in the trap body. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.5.3.1.12 | ColumnwtWebioEA2x2ERPAlarmUdpIpAddr | read-write | mandatory | IP address of the UDP listener to which the Webio device should send UDP traps. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.5.3.1.13 | ColumnwtWebioEA2x2ERPAlarmUdpPort | read-write | mandatory | Port number of the UDP listener to which the Webio device should send UDP traps. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.5.3.1.14 | ColumnwtWebioEA2x2ERPAlarmUdpText | read-write | mandatory | This text appears in the UDP trap body. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.5.3.1.15 | ColumnwtWebioEA2x2ERPAlarmTcpIpAddr | read-write | mandatory | IP address of the TCP listener to which the Webio device should send TCP traps. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.5.3.1.16 | ColumnwtWebioEA2x2ERPAlarmTcpPort | read-write | mandatory | Port number of the TCP listener to which the Webio device should send TCP traps. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.5.3.1.17 | ColumnwtWebioEA2x2ERPAlarmTcpText | read-write | mandatory | This text appears in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.5.3.1.18 | ColumnwtWebioEA2x2ERPAlarmSyslogIpAddr | read-write | mandatory | IP address of the syslog server to which the Webio device should send syslog messages. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.5.3.1.19 | ColumnwtWebioEA2x2ERPAlarmSyslogPort | read-write | mandatory | Port number of the syslog server to which the Webio device should send syslog messages. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.5.3.1.20 | ColumnwtWebioEA2x2ERPAlarmSyslogText | read-write | mandatory | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.5.3.1.21 | ColumnwtWebioEA2x2ERPAlarmFtpDataPort | read-write | mandatory | Local data port: 1..65535 or AUTO: the next free port will be assigned. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.5.3.1.22 | ColumnwtWebioEA2x2ERPAlarmFtpFileName | read-write | mandatory | Name of the file including path informations. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.5.3.1.23 | ColumnwtWebioEA2x2ERPAlarmFtpText | read-write | mandatory | Message text to store on the FTP server. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.5.3.1.24 | ColumnwtWebioEA2x2ERPAlarmFtpOption | read-write | mandatory | Binary coded options, select only one option at the same time: STORE = replace file APPEND = append message at the end of the file Octet 1: unused Octet 2: unu… |
| 1.3.6.1.4.1.5040.1.2.25.3.1.5.3.1.25 | ColumnwtWebioEA2x2ERPAlarmTimerCron | read-write | mandatory | This entry contains 5 space or tab seperated text fields for time trigger definition. Each field must match with the actual time to trigger a message, weekday … |
| 1.3.6.1.4.1.5040.1.2.25.3.1.5.3.1.26 | ColumnwtWebioEA2x2ERPAlarmMailReleaseSubject | read-write | mandatory | Subject line for alarm mail. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.5.3.1.27 | ColumnwtWebioEA2x2ERPAlarmMailReleaseText | read-write | mandatory | Release Alarm mail text: States of the Webio device can be included by using special tags. Please refer to the respective Webio manual |
| 1.3.6.1.4.1.5040.1.2.25.3.1.5.3.1.28 | ColumnwtWebioEA2x2ERPAlarmSnmpTrapReleaseText | read-write | mandatory | This text appears in the trap body. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.5.3.1.29 | ColumnwtWebioEA2x2ERPAlarmUdpReleaseText | read-write | mandatory | This text appears in the UDP trap body. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.5.3.1.30 | ColumnwtWebioEA2x2ERPAlarmTcpReleaseText | read-write | mandatory | This text appears in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.5.3.1.31 | ColumnwtWebioEA2x2ERPAlarmSyslogReleaseText | read-write | mandatory | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.5.3.1.32 | ColumnwtWebioEA2x2ERPAlarmFtpReleaseText | read-write | mandatory | Message text to store on the FTP server. |
| 1.3.6.1.4.1.5040.1.2.25.3.1.5.4 | ScalarwtWebioEA2x2ERPLoadControlView | read-only | mandatory | Here the result of automatic load control can be read. All output were tested in pairs (0-1). If an error occours at one output, both output of an pair will be… |
| 1.3.6.1.4.1.5040.1.2.25.3.1.5.5 | ScalarwtWebioEA2x2ERPLCShutDownView | read-write | mandatory | Here the result of the automatic load control shut down can be read. All outputs remain switched of, until a zero is written into this variable. But previously… |
| 1.3.6.1.4.1.5040.1.2.25.3.2 | NodewtWebioEA2x2ERPPorts | |||
| 1.3.6.1.4.1.5040.1.2.25.3.2.1 | TablewtWebioEA2x2ERPInputPortTable | not-accessible | mandatory | List of settings depending on the input number. |
| 1.3.6.1.4.1.5040.1.2.25.3.2.1.1 | RowwtWebioEA2x2ERPInputPortEntry | not-accessible | mandatory | Input parameter for the individual inputs. |
| 1.3.6.1.4.1.5040.1.2.25.3.2.1.1.1 | ColumnwtWebioEA2x2ERPPortInputName | read-write | mandatory | Name of the input. |
| 1.3.6.1.4.1.5040.1.2.25.3.2.1.1.2 | ColumnwtWebioEA2x2ERPPortInputText | read-write | mandatory | Description of the input. |
| 1.3.6.1.4.1.5040.1.2.25.3.2.1.1.3 | ColumnwtWebioEA2x2ERPPortInputMode | read-write | mandatory | Binary coded modes: Selecting short pulse detection enable by setting the corresponding bit to 1 enables interrupt support for counting. Only positive edges ar… |
| 1.3.6.1.4.1.5040.1.2.25.3.2.1.1.4 | ColumnwtWebioEA2x2ERPPortInputFilter | read-write | mandatory | Pulses with a duration shorter than here specified (duration in 1/1000 sec), are ignored. |
| 1.3.6.1.4.1.5040.1.2.25.3.2.1.1.5 | ColumnwtWebioEA2x2ERPPortInputBicountPulsePolarity | read-write | mandatory | This value defines the polarity of the input pulse. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 0 : negative polarity Bit 1 : positive polarit… |
| 1.3.6.1.4.1.5040.1.2.25.3.2.1.1.6 | ColumnwtWebioEA2x2ERPPortInputBicountInactivTimeout | read-write | mandatory | Pulse chains with a duration shorter than here specified (in 1/10 sek), are ignored. |
| 1.3.6.1.4.1.5040.1.2.25.3.2.2 | TablewtWebioEA2x2ERPOutputPortTable | not-accessible | mandatory | List of settings depending on the output number. |
| 1.3.6.1.4.1.5040.1.2.25.3.2.2.1 | RowwtWebioEA2x2ERPOutputPortEntry | not-accessible | mandatory | Output parameters of the individual outputs. |
| 1.3.6.1.4.1.5040.1.2.25.3.2.2.1.1 | ColumnwtWebioEA2x2ERPPortOutputName | read-write | mandatory | Name of the output. |
| 1.3.6.1.4.1.5040.1.2.25.3.2.2.1.2 | ColumnwtWebioEA2x2ERPPortOutputText | read-write | mandatory | Description of the output. |
| 1.3.6.1.4.1.5040.1.2.25.3.2.2.1.3 | ColumnwtWebioEA2x2ERPPortOutputGroupMode | read-write | mandatory | It is possible to connect outputs together to increase the output current. This could be done by connecting 2 or 4 outputs in a group together. All bits of suc… |
| 1.3.6.1.4.1.5040.1.2.25.3.2.2.1.4 | ColumnwtWebioEA2x2ERPPortOutputSafetyState | read-write | mandatory | This variable allows setting of individual digital outputs. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds … |
| 1.3.6.1.4.1.5040.1.2.25.3.2.2.1.5 | ColumnwtWebioEA2x2ERPPortLogicInputMask | read-write | mandatory | Selecting one of these inputs by setting the corresponding bit to 1 enables the logic function for the output identified by the index within this table. The ca… |
| 1.3.6.1.4.1.5040.1.2.25.3.2.2.1.6 | ColumnwtWebioEA2x2ERPPortLogicInputInverter | read-write | mandatory | Every input bit selected here will be inverted. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 0-1 : inputs 0-1 |
| 1.3.6.1.4.1.5040.1.2.25.3.2.2.1.7 | ColumnwtWebioEA2x2ERPPortLogicFunction | read-write | mandatory | This determines the logic function. No more than one function may be selected. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 0 : logic function … |
| 1.3.6.1.4.1.5040.1.2.25.3.2.2.1.8 | ColumnwtWebioEA2x2ERPPortLogicOutputInverter | read-write | mandatory | The logical operation result could be inverteted by setting the corresponding bit to 1. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 0 : Output… |
| 1.3.6.1.4.1.5040.1.2.25.3.2.2.1.9 | ColumnwtWebioEA2x2ERPPortPulseDuration | read-write | mandatory | Pulse length in 1/1000 sec. Setting this value to zero, disables the pulse output. |
| 1.3.6.1.4.1.5040.1.2.25.3.2.2.1.10 | ColumnwtWebioEA2x2ERPPortPulsePolarity | read-write | mandatory | This value defines the polarity of the output pulse, if wtWebioEA2x2ERPPortPulseDuration is not set to zero. After the pulse is finished, the output switches b… |
| 1.3.6.1.4.1.5040.1.2.25.3.3 | NodewtWebioEA2x2ERPManufact | |||
| 1.3.6.1.4.1.5040.1.2.25.3.3.1 | ScalarwtWebioEA2x2ERPMfName | read-write | mandatory | Manufacturer company name |
| 1.3.6.1.4.1.5040.1.2.25.3.3.2 | ScalarwtWebioEA2x2ERPMfAddr | read-write | mandatory | Manufacturer address. |
| 1.3.6.1.4.1.5040.1.2.25.3.3.3 | ScalarwtWebioEA2x2ERPMfHotline | read-write | mandatory | Manufacturer hotline. |
| 1.3.6.1.4.1.5040.1.2.25.3.3.4 | ScalarwtWebioEA2x2ERPMfInternet | read-write | mandatory | Manufacturer Internet address. |
| 1.3.6.1.4.1.5040.1.2.25.3.3.5 | ScalarwtWebioEA2x2ERPMfDeviceTyp | read-write | mandatory | Manufacturer device name (model number). |
| 1.3.6.1.4.1.5040.1.2.25.4 | NodewtWebioEA2x2ERPDiag | |||
| 1.3.6.1.4.1.5040.1.2.25.4.1 | ScalarwtWebioEA2x2ERPDiagErrorCount | read-only | mandatory | Number of entries in the error memory. |
| 1.3.6.1.4.1.5040.1.2.25.4.2 | ScalarwtWebioEA2x2ERPDiagBinaryError | read-only | mandatory | Error causes coded bit-by-bit. |
| 1.3.6.1.4.1.5040.1.2.25.4.3 | ScalarwtWebioEA2x2ERPDiagErrorIndex | read-write | mandatory | The value of this variable is used as an index to read an error massege from wtWebioEA2x2ERPDiagErrorMessage. Errors are numbered from 1 to wtWebioEA2x2ERPDiag… |
| 1.3.6.1.4.1.5040.1.2.25.4.4 | ScalarwtWebioEA2x2ERPDiagErrorMessage | read-only | mandatory | Using wtWebioEA2x2ERPDiagErrorIndex as an index, the appropriate message is available. |
| 1.3.6.1.4.1.5040.1.2.25.4.5 | ScalarwtWebioEA2x2ERPDiagErrorClear | write-only | mandatory | Writing 1 into this variable clears all diagnosis messages. |
| 1.3.6.1.4.1.5040.1.2.25.41 | NodewtWebioEA2x2ERPAlert1 | This SNMP trap is generated when Alarm 1 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.25.42 | NodewtWebioEA2x2ERPAlert2 | This SNMP trap is generated when Alarm 2 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.25.43 | NodewtWebioEA2x2ERPAlert3 | This SNMP trap is generated when Alarm 3 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.25.44 | NodewtWebioEA2x2ERPAlert4 | This SNMP trap is generated when Alarm 4 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.25.45 | NodewtWebioEA2x2ERPAlert5 | This SNMP trap is generated when Alarm 5 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.25.46 | NodewtWebioEA2x2ERPAlert6 | This SNMP trap is generated when Alarm 6 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.25.47 | NodewtWebioEA2x2ERPAlert7 | This SNMP trap is generated when Alarm 7 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.25.48 | NodewtWebioEA2x2ERPAlert8 | This SNMP trap is generated when Alarm 8 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.25.49 | NodewtWebioEA2x2ERPAlert9 | This SNMP trap is generated when Alarm 9 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.25.50 | NodewtWebioEA2x2ERPAlert10 | This SNMP trap is generated when Alarm 10 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.25.51 | NodewtWebioEA2x2ERPAlert11 | This SNMP trap is generated when Alarm 11 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.25.52 | NodewtWebioEA2x2ERPAlert12 | This SNMP trap is generated when Alarm 12 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.25.71 | NodewtWebioEA2x2ERPAlert13 | This SNMP trap is generated when Alarm 1 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.25.72 | NodewtWebioEA2x2ERPAlert14 | This SNMP trap is generated when Alarm 2 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.25.73 | NodewtWebioEA2x2ERPAlert15 | This SNMP trap is generated when Alarm 3 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.25.74 | NodewtWebioEA2x2ERPAlert16 | This SNMP trap is generated when Alarm 4 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.25.75 | NodewtWebioEA2x2ERPAlert17 | This SNMP trap is generated when Alarm 5 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.25.76 | NodewtWebioEA2x2ERPAlert18 | This SNMP trap is generated when Alarm 6 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.25.77 | NodewtWebioEA2x2ERPAlert19 | This SNMP trap is generated when Alarm 7 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.25.78 | NodewtWebioEA2x2ERPAlert20 | This SNMP trap is generated when Alarm 8 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.25.79 | NodewtWebioEA2x2ERPAlert21 | This SNMP trap is generated when Alarm 9 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.25.80 | NodewtWebioEA2x2ERPAlert22 | This SNMP trap is generated when Alarm 10 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.25.81 | NodewtWebioEA2x2ERPAlert23 | This SNMP trap is generated when Alarm 11 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.25.82 | NodewtWebioEA2x2ERPAlert24 | This SNMP trap is generated when Alarm 12 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.25.110 | NodewtWebioEA2x2ERPAlertDiag | This SNMP trap is generated when a diagnosis/error message was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.26 | NodewtWebioEA12x6RelERP | |||
| 1.3.6.1.4.1.5040.1.2.26.1 | NodewtWebioEA12x6RelERPInOut | |||
| 1.3.6.1.4.1.5040.1.2.26.1.1 | ScalarwtWebioEA12x6RelERPInputs | read-only | mandatory | Number of idependent inputs. |
| 1.3.6.1.4.1.5040.1.2.26.1.2 | ScalarwtWebioEA12x6RelERPOutputs | read-only | mandatory | Number of independent outputs. |
| 1.3.6.1.4.1.5040.1.2.26.1.3 | TablewtWebioEA12x6RelERPInputTable | not-accessible | mandatory | List of input indices. |
| 1.3.6.1.4.1.5040.1.2.26.1.3.1 | RowwtWebioEA12x6RelERPInputEntry | not-accessible | mandatory | Number of the inputs. |
| 1.3.6.1.4.1.5040.1.2.26.1.3.1.1 | ColumnwtWebioEA12x6RelERPInputNo | read-only | mandatory | Index numbers of the inputs. |
| 1.3.6.1.4.1.5040.1.2.26.1.3.1.2 | ColumnwtWebioEA12x6RelERPInputCounter | read-only | mandatory | Value of the input counter. |
| 1.3.6.1.4.1.5040.1.2.26.1.3.1.3 | ColumnwtWebioEA12x6RelERPInputCounterClear | read-only | mandatory | Clears the input counter after returning its value. |
| 1.3.6.1.4.1.5040.1.2.26.1.4 | ScalarwtWebioEA12x6RelERPInputValue | read-only | mandatory | This variable is used to read the inputs of the digital I/O port. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an input. Bit 0 corresp… |
| 1.3.6.1.4.1.5040.1.2.26.1.5 | TablewtWebioEA12x6RelERPOutputTable | not-accessible | mandatory | List of output indices. |
| 1.3.6.1.4.1.5040.1.2.26.1.5.1 | RowwtWebioEA12x6RelERPOutputEntry | not-accessible | mandatory | Number of the outputs. |
| 1.3.6.1.4.1.5040.1.2.26.1.5.1.1 | ColumnwtWebioEA12x6RelERPOutputNo | read-only | mandatory | Output number. |
| 1.3.6.1.4.1.5040.1.2.26.1.5.1.2 | ColumnwtWebioEA12x6RelERPOutputState | read-write | mandatory | Setting and reading of the states of the outputs, 0-OFF, 1-ON. |
| 1.3.6.1.4.1.5040.1.2.26.1.6 | ScalarwtWebioEA12x6RelERPOutputValue | read-write | mandatory | This variable is used to read and write the outputs of the digital I/O port. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. B… |
| 1.3.6.1.4.1.5040.1.2.26.1.7 | ScalarwtWebioEA12x6RelERPSetOutput | read-write | mandatory | This variable allows setting of individual digital outputs. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds … |
| 1.3.6.1.4.1.5040.1.2.26.2 | NodewtWebioEA12x6RelERPSessCntrl | |||
| 1.3.6.1.4.1.5040.1.2.26.2.1 | ScalarwtWebioEA12x6RelERPSessCntrlPassword | read-write | mandatory | Entering this password opens a session which is ended by writing a 1 to wtWebioEA12x6RelERPSessCntrlLogout. When read this variable provides a string of length… |
| 1.3.6.1.4.1.5040.1.2.26.2.2 | ScalarwtWebioEA12x6RelERPSessCntrlConfigMode | read-only | mandatory | When the device is in SNMP configuration mode, the value 1 is returned, otherwise 0. If the read value is 0 even though the password was written, the device is… |
| 1.3.6.1.4.1.5040.1.2.26.2.3 | ScalarwtWebioEA12x6RelERPSessCntrlLogout | read-write | mandatory | If the device is in configuration mode and the session was opened by this SNMP Manager, writing a 1 to this variable will end the session and all parameters ar… |
| 1.3.6.1.4.1.5040.1.2.26.2.4 | ScalarwtWebioEA12x6RelERPSessCntrlAdminPassword | read-write | mandatory | This password protects access to the variables with administrator rights. It can only be changed by the administrator. If no password was assigned, the valid p… |
| 1.3.6.1.4.1.5040.1.2.26.2.5 | ScalarwtWebioEA12x6RelERPSessCntrlConfigPassword | read-write | mandatory | This password protects access to the variables with configurator rights. It can be changed by the administrator and by the configurator. If no password was ass… |
| 1.3.6.1.4.1.5040.1.2.26.3 | NodewtWebioEA12x6RelERPConfig | |||
| 1.3.6.1.4.1.5040.1.2.26.3.1 | NodewtWebioEA12x6RelERPDevice | |||
| 1.3.6.1.4.1.5040.1.2.26.3.1.1 | NodewtWebioEA12x6RelERPText | |||
| 1.3.6.1.4.1.5040.1.2.26.3.1.1.1 | ScalarwtWebioEA12x6RelERPDeviceName | read-write | mandatory | Name of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.1.2 | ScalarwtWebioEA12x6RelERPDeviceText | read-write | mandatory | Description of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.1.3 | ScalarwtWebioEA12x6RelERPDeviceLocation | read-write | mandatory | Description of the location of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.1.4 | ScalarwtWebioEA12x6RelERPDeviceContact | read-write | mandatory | Contact address of the system operator of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.2 | NodewtWebioEA12x6RelERPTimeDate | |||
| 1.3.6.1.4.1.5040.1.2.26.3.1.2.1 | NodewtWebioEA12x6RelERPTimeZone | |||
| 1.3.6.1.4.1.5040.1.2.26.3.1.2.1.1 | ScalarwtWebioEA12x6RelERPTzOffsetHrs | read-write | mandatory | Offset hours for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.2.1.2 | ScalarwtWebioEA12x6RelERPTzOffsetMin | read-write | mandatory | Offset minutes for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.2.1.3 | ScalarwtWebioEA12x6RelERPTzEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Timezone |
| 1.3.6.1.4.1.5040.1.2.26.3.1.2.1.4 | ScalarwtWebioEA12x6RelERPStTzOffsetHrs | read-write | mandatory | Offset hours of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.2.1.5 | ScalarwtWebioEA12x6RelERPStTzOffsetMin | read-write | mandatory | Offset minutes of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.2.1.6 | ScalarwtWebioEA12x6RelERPStTzEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Summertime |
| 1.3.6.1.4.1.5040.1.2.26.3.1.2.1.7 | ScalarwtWebioEA12x6RelERPStTzStartMonth | read-write | mandatory | Month in which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.2.1.8 | ScalarwtWebioEA12x6RelERPStTzStartMode | read-write | mandatory | Mode of the day of the week for which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.2.1.9 | ScalarwtWebioEA12x6RelERPStTzStartWday | read-write | mandatory | Day of the week on which the change is made from winter time to summer time |
| 1.3.6.1.4.1.5040.1.2.26.3.1.2.1.10 | ScalarwtWebioEA12x6RelERPStTzStartHrs | read-write | mandatory | Hour in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.2.1.11 | ScalarwtWebioEA12x6RelERPStTzStartMin | read-write | mandatory | Minute in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.2.1.12 | ScalarwtWebioEA12x6RelERPStTzStopMonth | read-write | mandatory | Month in which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.2.1.13 | ScalarwtWebioEA12x6RelERPStTzStopMode | read-write | mandatory | Mode of the week day on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.2.1.14 | ScalarwtWebioEA12x6RelERPStTzStopWday | read-write | mandatory | Day of the week on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.2.1.15 | ScalarwtWebioEA12x6RelERPStTzStopHrs | read-write | mandatory | Hour at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.2.1.16 | ScalarwtWebioEA12x6RelERPStTzStopMin | read-write | mandatory | Minute at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.2.2 | NodewtWebioEA12x6RelERPTimeServer | |||
| 1.3.6.1.4.1.5040.1.2.26.3.1.2.2.1 | ScalarwtWebioEA12x6RelERPTimeServer1 | read-write | mandatory | IP address or name of the 1st time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.26.3.1.2.2.2 | ScalarwtWebioEA12x6RelERPTimeServer2 | read-write | mandatory | IP address or name of the 2nd time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.26.3.1.2.2.3 | ScalarwtWebioEA12x6RelERPTsEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Time Server |
| 1.3.6.1.4.1.5040.1.2.26.3.1.2.2.4 | ScalarwtWebioEA12x6RelERPTsSyncTime | read-write | mandatory | Daily synchronisation time with the time server (hour: 0-23). |
| 1.3.6.1.4.1.5040.1.2.26.3.1.2.3 | NodewtWebioEA12x6RelERPDeviceClock | |||
| 1.3.6.1.4.1.5040.1.2.26.3.1.2.3.1 | ScalarwtWebioEA12x6RelERPClockHrs | read-write | mandatory | Clock hours taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.2.3.2 | ScalarwtWebioEA12x6RelERPClockMin | read-write | mandatory | Clock minutes taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.2.3.3 | ScalarwtWebioEA12x6RelERPClockDay | read-write | mandatory | Date: Day of the month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.2.3.4 | ScalarwtWebioEA12x6RelERPClockMonth | read-write | mandatory | Date: Month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.2.3.5 | ScalarwtWebioEA12x6RelERPClockYear | read-write | mandatory | Date: Year, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3 | NodewtWebioEA12x6RelERPBasic | |||
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.1 | NodewtWebioEA12x6RelERPNetwork | |||
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.1.1 | ScalarwtWebioEA12x6RelERPIpAddress | read-write | mandatory | IP address of the Webio |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.1.2 | ScalarwtWebioEA12x6RelERPSubnetMask | read-write | mandatory | Subnet mask of the Webio |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.1.3 | ScalarwtWebioEA12x6RelERPGateway | read-write | mandatory | Gateway of the Webio |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.1.4 | ScalarwtWebioEA12x6RelERPDnsServer1 | read-write | mandatory | IP address of the 1st DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.1.5 | ScalarwtWebioEA12x6RelERPDnsServer2 | read-write | mandatory | IP address of the 2nd DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.1.6 | ScalarwtWebioEA12x6RelERPAddConfig | read-write | mandatory | Additional configuration (1=ON): Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1: DHCP enable Bit 0: BOOTP enable |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.2 | NodewtWebioEA12x6RelERPHTTP | |||
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.2.1 | ScalarwtWebioEA12x6RelERPStartup | read-write | mandatory | Binary coded start page, more than one page must not be selected: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 2: user.htm Bit 1: home.htm Bit … |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.2.2 | ScalarwtWebioEA12x6RelERPGetHeaderEnable | read-write | mandatory | If bits are set, every answer of a short form GET question will be lead by the IP-address and name of the device (Header) or a HTTP header (HTTP): Octet 1: unu… |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.2.3 | ScalarwtWebioEA12x6RelERPHttpInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.2.4 | ScalarwtWebioEA12x6RelERPHttpPort | read-write | mandatory | Definition of the standard HTML port (Default: 80). |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.3 | NodewtWebioEA12x6RelERPMail | |||
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.3.1 | ScalarwtWebioEA12x6RelERPMailAdName | read-write | mandatory | Device name for mail administration. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.3.2 | ScalarwtWebioEA12x6RelERPMailReply | read-write | mandatory | Reply address for the mail server. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.3.3 | ScalarwtWebioEA12x6RelERPMailServer | read-write | mandatory | Name or IP address of the mail server. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.3.4 | ScalarwtWebioEA12x6RelERPMailEnable | read-write | mandatory | Set this bit to enable the sending of mails: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Mail enable |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.3.5 | ScalarwtWebioEA12x6RelERPMailAuthentication | read-write | mandatory | Selection of the authentication modi: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTE… |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.3.6 | ScalarwtWebioEA12x6RelERPMailAuthUser | read-write | mandatory | Name of the user to be authenticated. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.3.7 | ScalarwtWebioEA12x6RelERPMailAuthPassword | read-write | mandatory | Authentication password. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.3.8 | ScalarwtWebioEA12x6RelERPMailPop3Server | read-write | mandatory | Name or Ip-address of the POP3 Servers. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.4 | NodewtWebioEA12x6RelERPSNMP | |||
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.4.1 | ScalarwtWebioEA12x6RelERPSnmpEnable | read-write | mandatory | Set bit 0 to enable SNMP. If disabled, the device did not respond to any SNMP requests. Bit 1 decided wether the community string of read operations is compare… |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.4.2 | ScalarwtWebioEA12x6RelERPSnmpCommunityStringRead | read-write | mandatory | Community string read only |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.4.3 | ScalarwtWebioEA12x6RelERPSnmpCommunityStringReadWrite | read-write | mandatory | Community string read / write |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.4.4 | ScalarwtWebioEA12x6RelERPSnmpSystemTrapManagerIP | read-write | mandatory | Name or IP address of the TCP server which accepts the system trap. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.4.5 | ScalarwtWebioEA12x6RelERPSnmpSystemTrapEnable | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2: Diag messages Bit 3-7: unused |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.5 | NodewtWebioEA12x6RelERPUDP | |||
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.5.1 | ScalarwtWebioEA12x6RelERPUdpAdminPort | read-write | mandatory | Udp port to which the Udp queries ( short form GET requests) can be sent. This port number must be unique within the device. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.5.2 | ScalarwtWebioEA12x6RelERPUdpEnable | read-write | mandatory | Set this bit to enable UDP support: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : UDP enable |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.5.3 | ScalarwtWebioEA12x6RelERPUdpRemotePort | read-write | mandatory | Udp remote port setting. If this value is set to zero, the source port read from a request will be used as destination port for the answer. A non zero value fo… |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.6 | NodewtWebioEA12x6RelERPBinary | |||
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.6.1 | ScalarwtWebioEA12x6RelERPBinaryModeCount | read-only | mandatory | Number of independent binary channels. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.6.2 | TablewtWebioEA12x6RelERPBinaryIfTable | not-accessible | mandatory | Table of indices. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.6.2.1 | RowwtWebioEA12x6RelERPBinaryIfEntry | not-accessible | mandatory | Indices of the binary channels. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.6.2.1.1 | ColumnwtWebioEA12x6RelERPBinaryModeNo | read-only | mandatory | Number of the binary channel. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.6.3 | TablewtWebioEA12x6RelERPBinaryTable | not-accessible | mandatory | Table of properties of the binary mode. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.6.3.1 | RowwtWebioEA12x6RelERPBinaryEntry | not-accessible | mandatory | Binary properties. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.6.3.1.1 | ColumnwtWebioEA12x6RelERPBinaryOperationMode | read-write | mandatory | Selection of the operation mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: … |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.6.3.1.2 | ColumnwtWebioEA12x6RelERPBinaryTcpServerLocalPort | read-write | mandatory | Local TCP port for data exchange in this server mode. This port number must be unique within the device. Reserved port number must not be used (refere to the m… |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.6.3.1.3 | ColumnwtWebioEA12x6RelERPBinaryTcpServerInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.6.3.1.4 | ColumnwtWebioEA12x6RelERPBinaryTcpServerApplicationMode | read-write | mandatory | Selection of the application mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4… |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.6.3.1.5 | ColumnwtWebioEA12x6RelERPBinaryTcpClientLocalPort | read-write | mandatory | Local TCP port for data exchange in this client mode. This port number must be unique within the device. Reserved port number must not be used (refere to the m… |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.6.3.1.6 | ColumnwtWebioEA12x6RelERPBinaryTcpClientServerPort | read-write | mandatory | Port number of the server. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when setting t… |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.6.3.1.7 | ColumnwtWebioEA12x6RelERPBinaryTcpClientServerIpAddr | read-write | mandatory | Ip address of the server. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when setting th… |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.6.3.1.8 | ColumnwtWebioEA12x6RelERPBinaryTcpClientServerPassword | read-write | mandatory | Building a connection may be protected by the administrator password of the server. Enter the server password to establish the connection, if a server administ… |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.6.3.1.9 | ColumnwtWebioEA12x6RelERPBinaryTcpClientInactivity | read-write | mandatory | Connection timeout in 100ms. If no data are exchanged within the specified time, the device closes the connection to the server. The value 0 deactivates the ti… |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.6.3.1.10 | ColumnwtWebioEA12x6RelERPBinaryTcpClientInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.6.3.1.11 | ColumnwtWebioEA12x6RelERPBinaryTcpClientInterval | read-write | mandatory | Configurable interval with a 100ms base, in which the Webio device sends data to the configured application. A interval of zero stopps the periodical sending. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.6.3.1.12 | ColumnwtWebioEA12x6RelERPBinaryTcpClientApplicationMode | read-write | mandatory | Selection of the application mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4… |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.6.3.1.13 | ColumnwtWebioEA12x6RelERPBinaryUdpPeerLocalPort | read-write | mandatory | Local UDP port for data exchange in this peer to peer mode. This port number must be unique within the device. Reserved port number must not be used (refere to… |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.6.3.1.14 | ColumnwtWebioEA12x6RelERPBinaryUdpPeerRemotePort | read-write | mandatory | Port number of the remote device. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when se… |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.6.3.1.15 | ColumnwtWebioEA12x6RelERPBinaryUdpPeerRemoteIpAddr | read-write | mandatory | Ip address of the remote device. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when set… |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.6.3.1.16 | ColumnwtWebioEA12x6RelERPBinaryUdpPeerInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.6.3.1.17 | ColumnwtWebioEA12x6RelERPBinaryUdpPeerInterval | read-write | mandatory | Configurable interval with a 100ms base, in which the Webio device sends data to the configured remote device. A interval of zero stopps the periodical sending. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.6.3.1.18 | ColumnwtWebioEA12x6RelERPBinaryUdpPeerApplicationMode | read-write | mandatory | Selection of the application mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4… |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.6.3.1.19 | ColumnwtWebioEA12x6RelERPBinaryConnectedPort | read-only | mandatory | Port number of the remote device, after connection has been established. In case of no connection or missing port informations a zero will be read. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.6.3.1.20 | ColumnwtWebioEA12x6RelERPBinaryConnectedIpAddr | read-only | mandatory | IP address of the remote device, after connection has been established. In case of no connection or missing port informations 0.0.0.0 will be read. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.6.3.1.21 | ColumnwtWebioEA12x6RelERPBinaryTcpServerClientHttpPort | read-write | mandatory | HTTP port number of the remote device at TCP Server Mode. If an mailfunction occurs status informations will be send to this port. Not used at mode Compatible … |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.6.3.1.22 | ColumnwtWebioEA12x6RelERPBinaryTcpClientServerHttpPort | read-write | mandatory | HTTP port number of the remote device at TCP Client Mode. In the operating mode Box2Box connection status informations will be exchanged through this port. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.7 | NodewtWebioEA12x6RelERPSyslog | |||
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.7.1 | ScalarwtWebioEA12x6RelERPSyslogServerIP | read-write | mandatory | Name or IP address of the Syslog server, which accepts the Syslog messgaes. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.7.2 | ScalarwtWebioEA12x6RelERPSyslogServerPort | read-write | mandatory | Portnumber of the Syslog servers, default 514. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.7.3 | ScalarwtWebioEA12x6RelERPSyslogSystemMessagesEnable | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2: Diag Messages Bit 3-7: unused |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.7.4 | ScalarwtWebioEA12x6RelERPSyslogEnable | read-write | mandatory | Set bit 0to enable Syslog: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Syslog enable |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.8 | NodewtWebioEA12x6RelERPFTP | |||
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.8.1 | ScalarwtWebioEA12x6RelERPFTPServerIP | read-write | mandatory | Name or IP address of the FTP server, which accepts the FTP messages. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.8.2 | ScalarwtWebioEA12x6RelERPFTPServerControlPort | read-write | mandatory | Portnumber of the control port of the FTP server, default 21. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.8.3 | ScalarwtWebioEA12x6RelERPFTPUserName | read-write | mandatory | FTP Loggin: user name. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.8.4 | ScalarwtWebioEA12x6RelERPFTPPassword | read-write | mandatory | FTP Loggin: user password. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.8.5 | ScalarwtWebioEA12x6RelERPFTPAccount | read-write | mandatory | FTP Loggin: name of account. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.8.6 | ScalarwtWebioEA12x6RelERPFTPOption | read-write | mandatory | Bit 0 switches the FTP Server in Passiv-Mode, the Client controls the data connection on its own: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit … |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.8.7 | ScalarwtWebioEA12x6RelERPFTPEnable | read-write | mandatory | Set Bit 0 to enable FTP: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : FTP enable |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.10 | NodewtWebioEA12x6RelERPWayBack | |||
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.10.1 | ScalarwtWebioEA12x6RelERPWayBackEnable | read-write | mandatory | Set Bit 0 to enable WayBack: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : WayBack enable |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.10.2 | ScalarwtWebioEA12x6RelERPWayBackServerControlPort | read-write | mandatory | Portnumber of the control port of the FTP server, default 21. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.10.3 | ScalarwtWebioEA12x6RelERPWayBackFTPPassword | read-write | mandatory | WayBack FTP Loggin: Password of the user. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.10.4 | ScalarwtWebioEA12x6RelERPWayBackFTPResponse | read-write | mandatory | WayBack FTP response: return message after login. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.3.10.5 | ScalarwtWebioEA12x6RelERPWayBackFTPTimeOut | read-write | mandatory | WayBack FTP Timeout: a request must be finished within this periode of time. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.4 | NodewtWebioEA12x6RelERPOutputMode | |||
| 1.3.6.1.4.1.5040.1.2.26.3.1.4.1 | TablewtWebioEA12x6RelERPOutputModeTable | not-accessible | mandatory | Table of output mode configurations dependent on the output indices. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.4.1.1 | RowwtWebioEA12x6RelERPOutputModeEntry | not-accessible | mandatory | Output mode configurations of the individual outputs. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.4.1.1.1 | ColumnwtWebioEA12x6RelERPOutputModeBit | read-write | mandatory | This binary coded output mode defines the individual operation mode for any output. More than one mode must not be selected. The OCTETS are interpreted bit-by-… |
| 1.3.6.1.4.1.5040.1.2.26.3.1.4.2 | ScalarwtWebioEA12x6RelERPSafetyTimeout | read-write | mandatory | After this period of time (multiple of 100ms) without receiving data outputs switch to their Safety States. For each output a independend safety state could be… |
| 1.3.6.1.4.1.5040.1.2.26.3.1.5 | NodewtWebioEA12x6RelERPAlarm | |||
| 1.3.6.1.4.1.5040.1.2.26.3.1.5.1 | ScalarwtWebioEA12x6RelERPAlarmCount | read-only | mandatory | Number of independent alarms. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.5.2 | TablewtWebioEA12x6RelERPAlarmIfTable | not-accessible | mandatory | List of alarm indices. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.5.2.1 | RowwtWebioEA12x6RelERPAlarmIfEntry | not-accessible | mandatory | Numbers of the alarms. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.5.2.1.1 | ColumnwtWebioEA12x6RelERPAlarmNo | read-only | mandatory | Numbers of the alarms. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.5.3 | TablewtWebioEA12x6RelERPAlarmTable | not-accessible | mandatory | List of settings depending on the alarm number. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.5.3.1 | RowwtWebioEA12x6RelERPAlarmEntry | not-accessible | mandatory | Alarm parameters of the individual alarms. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.5.3.1.1 | ColumnwtWebioEA12x6RelERPAlarmInputTrigger | read-write | mandatory | This variable allows setting of individual input trigger conditions. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an input. Bit 0 corr… |
| 1.3.6.1.4.1.5040.1.2.26.3.1.5.3.1.2 | ColumnwtWebioEA12x6RelERPAlarmOutputTrigger | read-write | mandatory | This variable allows setting of individual output trigger conditions. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 co… |
| 1.3.6.1.4.1.5040.1.2.26.3.1.5.3.1.3 | ColumnwtWebioEA12x6RelERPAlarmSystemTrigger | read-write | mandatory | Binary coded trigger conditions: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, … |
| 1.3.6.1.4.1.5040.1.2.26.3.1.5.3.1.4 | ColumnwtWebioEA12x6RelERPAlarmMaxCounterValue | read-write | mandatory | This variable configures a max. counter value. If an input counter value exceeds this max. value, the corresponding alarm is triggered. Input counters with its… |
| 1.3.6.1.4.1.5040.1.2.26.3.1.5.3.1.5 | ColumnwtWebioEA12x6RelERPAlarmInterval | read-write | mandatory | Send interval for alarm messages. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.5.3.1.6 | ColumnwtWebioEA12x6RelERPAlarmEnable | read-write | mandatory | Binary coded alarm enable: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Mail Enable Bit 1: SNMP Trap enable Bit 2: UDP enable Bit 3: Send in… |
| 1.3.6.1.4.1.5040.1.2.26.3.1.5.3.1.7 | ColumnwtWebioEA12x6RelERPAlarmMailAddr | read-write | mandatory | E-Mail address for sending the alarm mail to. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.5.3.1.8 | ColumnwtWebioEA12x6RelERPAlarmMailSubject | read-write | mandatory | Subject line for alarm mail. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.5.3.1.9 | ColumnwtWebioEA12x6RelERPAlarmMailText | read-write | mandatory | Alarm mail text: States of the Webio device can be included by using special tags. Please refer to the respective Webio manual |
| 1.3.6.1.4.1.5040.1.2.26.3.1.5.3.1.10 | ColumnwtWebioEA12x6RelERPAlarmSnmpManagerIP | read-write | mandatory | IP address of the SNMP Manager to which the Webio device should send SNMP traps. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.5.3.1.11 | ColumnwtWebioEA12x6RelERPAlarmSnmpTrapText | read-write | mandatory | This text appears in the trap body. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.5.3.1.12 | ColumnwtWebioEA12x6RelERPAlarmUdpIpAddr | read-write | mandatory | IP address of the UDP listener to which the Webio device should send UDP traps. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.5.3.1.13 | ColumnwtWebioEA12x6RelERPAlarmUdpPort | read-write | mandatory | Port number of the UDP listener to which the Webio device should send UDP traps. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.5.3.1.14 | ColumnwtWebioEA12x6RelERPAlarmUdpText | read-write | mandatory | This text appears in the UDP trap body. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.5.3.1.15 | ColumnwtWebioEA12x6RelERPAlarmTcpIpAddr | read-write | mandatory | IP address of the TCP listener to which the Webio device should send TCP traps. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.5.3.1.16 | ColumnwtWebioEA12x6RelERPAlarmTcpPort | read-write | mandatory | Port number of the TCP listener to which the Webio device should send TCP traps. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.5.3.1.17 | ColumnwtWebioEA12x6RelERPAlarmTcpText | read-write | mandatory | This text appears in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.5.3.1.18 | ColumnwtWebioEA12x6RelERPAlarmSyslogIpAddr | read-write | mandatory | IP address of the syslog server to which the Webio device should send syslog messages. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.5.3.1.19 | ColumnwtWebioEA12x6RelERPAlarmSyslogPort | read-write | mandatory | Port number of the syslog server to which the Webio device should send syslog messages. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.5.3.1.20 | ColumnwtWebioEA12x6RelERPAlarmSyslogText | read-write | mandatory | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.5.3.1.21 | ColumnwtWebioEA12x6RelERPAlarmFtpDataPort | read-write | mandatory | Local data port: 1..65535 or AUTO: the next free port will be assigned. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.5.3.1.22 | ColumnwtWebioEA12x6RelERPAlarmFtpFileName | read-write | mandatory | Name of the file including path informations. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.5.3.1.23 | ColumnwtWebioEA12x6RelERPAlarmFtpText | read-write | mandatory | Message text to store on the FTP server. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.5.3.1.24 | ColumnwtWebioEA12x6RelERPAlarmFtpOption | read-write | mandatory | Binary coded options, select only one option at the same time: STORE = replace file APPEND = append message at the end of the file Octet 1: unused Octet 2: unu… |
| 1.3.6.1.4.1.5040.1.2.26.3.1.5.3.1.25 | ColumnwtWebioEA12x6RelERPAlarmTimerCron | read-write | mandatory | This entry contains 5 space or tab seperated text fields for time trigger definition. Each field must match with the actual time to trigger a message, weekday … |
| 1.3.6.1.4.1.5040.1.2.26.3.1.5.3.1.26 | ColumnwtWebioEA12x6RelERPAlarmMailReleaseSubject | read-write | mandatory | Subject line for alarm mail. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.5.3.1.27 | ColumnwtWebioEA12x6RelERPAlarmMailReleaseText | read-write | mandatory | Release Alarm mail text: States of the Webio device can be included by using special tags. Please refer to the respective Webio manual |
| 1.3.6.1.4.1.5040.1.2.26.3.1.5.3.1.28 | ColumnwtWebioEA12x6RelERPAlarmSnmpTrapReleaseText | read-write | mandatory | This text appears in the trap body. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.5.3.1.29 | ColumnwtWebioEA12x6RelERPAlarmUdpReleaseText | read-write | mandatory | This text appears in the UDP trap body. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.5.3.1.30 | ColumnwtWebioEA12x6RelERPAlarmTcpReleaseText | read-write | mandatory | This text appears in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.5.3.1.31 | ColumnwtWebioEA12x6RelERPAlarmSyslogReleaseText | read-write | mandatory | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body. |
| 1.3.6.1.4.1.5040.1.2.26.3.1.5.3.1.32 | ColumnwtWebioEA12x6RelERPAlarmFtpReleaseText | read-write | mandatory | Message text to store on the FTP server. |
| 1.3.6.1.4.1.5040.1.2.26.3.2 | NodewtWebioEA12x6RelERPPorts | |||
| 1.3.6.1.4.1.5040.1.2.26.3.2.1 | TablewtWebioEA12x6RelERPInputPortTable | not-accessible | mandatory | List of settings depending on the input number. |
| 1.3.6.1.4.1.5040.1.2.26.3.2.1.1 | RowwtWebioEA12x6RelERPInputPortEntry | not-accessible | mandatory | Input parameter for the individual inputs. |
| 1.3.6.1.4.1.5040.1.2.26.3.2.1.1.1 | ColumnwtWebioEA12x6RelERPPortInputName | read-write | mandatory | Name of the input. |
| 1.3.6.1.4.1.5040.1.2.26.3.2.1.1.2 | ColumnwtWebioEA12x6RelERPPortInputText | read-write | mandatory | Description of the input. |
| 1.3.6.1.4.1.5040.1.2.26.3.2.1.1.3 | ColumnwtWebioEA12x6RelERPPortInputMode | read-write | mandatory | Binary coded modes: Selecting short pulse detection enable by setting the corresponding bit to 1 enables interrupt support for counting. Only positive edges ar… |
| 1.3.6.1.4.1.5040.1.2.26.3.2.1.1.4 | ColumnwtWebioEA12x6RelERPPortInputFilter | read-write | mandatory | Pulses with a duration shorter than here specified (duration in 1/1000 sec), are ignored. |
| 1.3.6.1.4.1.5040.1.2.26.3.2.1.1.5 | ColumnwtWebioEA12x6RelERPPortInputBicountPulsePolarity | read-write | mandatory | This value defines the polarity of the input pulse. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 0 : negative polarity Bit 1 : positive polarit… |
| 1.3.6.1.4.1.5040.1.2.26.3.2.1.1.6 | ColumnwtWebioEA12x6RelERPPortInputBicountInactivTimeout | read-write | mandatory | Pulse chains with a duration shorter than here specified (in 1/10 sek), are ignored. |
| 1.3.6.1.4.1.5040.1.2.26.3.2.2 | TablewtWebioEA12x6RelERPOutputPortTable | not-accessible | mandatory | List of settings depending on the output number. |
| 1.3.6.1.4.1.5040.1.2.26.3.2.2.1 | RowwtWebioEA12x6RelERPOutputPortEntry | not-accessible | mandatory | Output parameters of the individual outputs. |
| 1.3.6.1.4.1.5040.1.2.26.3.2.2.1.1 | ColumnwtWebioEA12x6RelERPPortOutputName | read-write | mandatory | Name of the output. |
| 1.3.6.1.4.1.5040.1.2.26.3.2.2.1.2 | ColumnwtWebioEA12x6RelERPPortOutputText | read-write | mandatory | Description of the output. |
| 1.3.6.1.4.1.5040.1.2.26.3.2.2.1.3 | ColumnwtWebioEA12x6RelERPPortOutputGroupMode | read-write | mandatory | Unused in this device 57634 |
| 1.3.6.1.4.1.5040.1.2.26.3.2.2.1.4 | ColumnwtWebioEA12x6RelERPPortOutputSafetyState | read-write | mandatory | This variable allows setting of individual digital outputs. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds … |
| 1.3.6.1.4.1.5040.1.2.26.3.2.2.1.5 | ColumnwtWebioEA12x6RelERPPortLogicInputMask | read-write | mandatory | Selecting one of these inputs by setting the corresponding bit to 1 enables the logic function for the output identified by the index within this table. The ca… |
| 1.3.6.1.4.1.5040.1.2.26.3.2.2.1.6 | ColumnwtWebioEA12x6RelERPPortLogicInputInverter | read-write | mandatory | Every input bit selected here will be inverted. OCTET 1: unused OCTET 2: unused OCTET 3: Bit 0-3 : inputs 8-11 Bit 4-7 : unused OCTET 4: Bit 0-7 : inputs 0-7 |
| 1.3.6.1.4.1.5040.1.2.26.3.2.2.1.7 | ColumnwtWebioEA12x6RelERPPortLogicFunction | read-write | mandatory | This determines the logic function. No more than one function may be selected. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 0 : logic function … |
| 1.3.6.1.4.1.5040.1.2.26.3.2.2.1.8 | ColumnwtWebioEA12x6RelERPPortLogicOutputInverter | read-write | mandatory | The logical operation result could be inverteted by setting the corresponding bit to 1. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 0 : Output… |
| 1.3.6.1.4.1.5040.1.2.26.3.2.2.1.9 | ColumnwtWebioEA12x6RelERPPortPulseDuration | read-write | mandatory | Pulse length in 1/1000 sec. Setting this value to zero, disables the pulse output. |
| 1.3.6.1.4.1.5040.1.2.26.3.2.2.1.10 | ColumnwtWebioEA12x6RelERPPortPulsePolarity | read-write | mandatory | This value defines the polarity of the output pulse, if wtWebioEA12x6RelERPPortPulseDuration is not set to zero. After the pulse is finished, the output switch… |
| 1.3.6.1.4.1.5040.1.2.26.3.3 | NodewtWebioEA12x6RelERPManufact | |||
| 1.3.6.1.4.1.5040.1.2.26.3.3.1 | ScalarwtWebioEA12x6RelERPMfName | read-write | mandatory | Manufacturer company name |
| 1.3.6.1.4.1.5040.1.2.26.3.3.2 | ScalarwtWebioEA12x6RelERPMfAddr | read-write | mandatory | Manufacturer address. |
| 1.3.6.1.4.1.5040.1.2.26.3.3.3 | ScalarwtWebioEA12x6RelERPMfHotline | read-write | mandatory | Manufacturer hotline. |
| 1.3.6.1.4.1.5040.1.2.26.3.3.4 | ScalarwtWebioEA12x6RelERPMfInternet | read-write | mandatory | Manufacturer Internet address. |
| 1.3.6.1.4.1.5040.1.2.26.3.3.5 | ScalarwtWebioEA12x6RelERPMfDeviceTyp | read-write | mandatory | Manufacturer device name (model number). |
| 1.3.6.1.4.1.5040.1.2.26.3.3.6 | ScalarwtWebioEA12x6RelERPMfOrderNo | read-write | mandatory | Manufacturer part number. |
| 1.3.6.1.4.1.5040.1.2.26.4 | NodewtWebioEA12x6RelERPDiag | |||
| 1.3.6.1.4.1.5040.1.2.26.4.1 | ScalarwtWebioEA12x6RelERPDiagErrorCount | read-only | mandatory | Number of entries in the error memory. |
| 1.3.6.1.4.1.5040.1.2.26.4.2 | ScalarwtWebioEA12x6RelERPDiagBinaryError | read-only | mandatory | Error causes coded bit-by-bit. |
| 1.3.6.1.4.1.5040.1.2.26.4.3 | ScalarwtWebioEA12x6RelERPDiagErrorIndex | read-write | mandatory | The value of this variable is used as an index to read an error massege from wtWebioEA12x6RelERPDiagErrorMessage. Errors are numbered from 1 to wtWebioEA12x6Re… |
| 1.3.6.1.4.1.5040.1.2.26.4.4 | ScalarwtWebioEA12x6RelERPDiagErrorMessage | read-only | mandatory | Using wtWebioEA12x6RelERPDiagErrorIndex as an index, the appropriate message is available. |
| 1.3.6.1.4.1.5040.1.2.26.4.5 | ScalarwtWebioEA12x6RelERPDiagErrorClear | write-only | mandatory | Writing 1 into this variable clears all diagnosis messages. |
| 1.3.6.1.4.1.5040.1.2.26.41 | NodewtWebioEA12x6RelERPAlert1 | This SNMP trap is generated when Alarm 1 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.26.42 | NodewtWebioEA12x6RelERPAlert2 | This SNMP trap is generated when Alarm 2 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.26.43 | NodewtWebioEA12x6RelERPAlert3 | This SNMP trap is generated when Alarm 3 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.26.44 | NodewtWebioEA12x6RelERPAlert4 | This SNMP trap is generated when Alarm 4 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.26.45 | NodewtWebioEA12x6RelERPAlert5 | This SNMP trap is generated when Alarm 5 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.26.46 | NodewtWebioEA12x6RelERPAlert6 | This SNMP trap is generated when Alarm 6 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.26.47 | NodewtWebioEA12x6RelERPAlert7 | This SNMP trap is generated when Alarm 7 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.26.48 | NodewtWebioEA12x6RelERPAlert8 | This SNMP trap is generated when Alarm 8 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.26.49 | NodewtWebioEA12x6RelERPAlert9 | This SNMP trap is generated when Alarm 9 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.26.50 | NodewtWebioEA12x6RelERPAlert10 | This SNMP trap is generated when Alarm 10 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.26.51 | NodewtWebioEA12x6RelERPAlert11 | This SNMP trap is generated when Alarm 11 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.26.52 | NodewtWebioEA12x6RelERPAlert12 | This SNMP trap is generated when Alarm 12 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.26.71 | NodewtWebioEA12x6RelERPAlert13 | This SNMP trap is generated when Alarm 1 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.26.72 | NodewtWebioEA12x6RelERPAlert14 | This SNMP trap is generated when Alarm 2 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.26.73 | NodewtWebioEA12x6RelERPAlert15 | This SNMP trap is generated when Alarm 3 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.26.74 | NodewtWebioEA12x6RelERPAlert16 | This SNMP trap is generated when Alarm 4 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.26.75 | NodewtWebioEA12x6RelERPAlert17 | This SNMP trap is generated when Alarm 5 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.26.76 | NodewtWebioEA12x6RelERPAlert18 | This SNMP trap is generated when Alarm 6 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.26.77 | NodewtWebioEA12x6RelERPAlert19 | This SNMP trap is generated when Alarm 7 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.26.78 | NodewtWebioEA12x6RelERPAlert20 | This SNMP trap is generated when Alarm 8 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.26.79 | NodewtWebioEA12x6RelERPAlert21 | This SNMP trap is generated when Alarm 9 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.26.80 | NodewtWebioEA12x6RelERPAlert22 | This SNMP trap is generated when Alarm 10 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.26.81 | NodewtWebioEA12x6RelERPAlert23 | This SNMP trap is generated when Alarm 11 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.26.82 | NodewtWebioEA12x6RelERPAlert24 | This SNMP trap is generated when Alarm 12 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.26.110 | NodewtWebioEA12x6RelERPAlertDiag | This SNMP trap is generated when a diagnosis/error message was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.27 | NodewtIpWatcher | |||
| 1.3.6.1.4.1.5040.1.2.27.1 | NodewtIpWatcherInOut | |||
| 1.3.6.1.4.1.5040.1.2.27.1.1 | ScalarwtIpWatcherInputs | read-only | mandatory | Number of idependent inputs. |
| 1.3.6.1.4.1.5040.1.2.27.1.2 | ScalarwtIpWatcherOutputs | read-only | mandatory | Number of idependent outputs. |
| 1.3.6.1.4.1.5040.1.2.27.1.3 | TablewtIpWatcherInputTable | not-accessible | mandatory | List of input indices. |
| 1.3.6.1.4.1.5040.1.2.27.1.3.1 | RowwtIpWatcherInputEntry | not-accessible | mandatory | Number of the inputs. |
| 1.3.6.1.4.1.5040.1.2.27.1.3.1.1 | ColumnwtIpWatcherInputNo | read-only | mandatory | Index numbers of the inputs. |
| 1.3.6.1.4.1.5040.1.2.27.1.3.1.2 | ColumnwtIpWatcherInputCounter | read-only | mandatory | Value of the input counter. |
| 1.3.6.1.4.1.5040.1.2.27.1.3.1.3 | ColumnwtIpWatcherInputCounterClear | read-only | mandatory | Clears the input counter after returning its value. |
| 1.3.6.1.4.1.5040.1.2.27.1.3.1.4 | ColumnwtIpWatcherInputState | read-only | mandatory | Value of a single input bit, 0-OFF, 1-ON. |
| 1.3.6.1.4.1.5040.1.2.27.1.4 | ScalarwtIpWatcherInputValue | read-only | mandatory | This variable is used to read the inputs of the digital I/O port. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corres… |
| 1.3.6.1.4.1.5040.1.2.27.1.5 | TablewtIpWatcherOutputTable | not-accessible | mandatory | List of output indices. |
| 1.3.6.1.4.1.5040.1.2.27.1.5.1 | RowwtIpWatcherOutputEntry | not-accessible | mandatory | Number of the outputs. |
| 1.3.6.1.4.1.5040.1.2.27.1.5.1.1 | ColumnwtIpWatcherOutputNo | read-only | mandatory | Output number. |
| 1.3.6.1.4.1.5040.1.2.27.1.5.1.2 | ColumnwtIpWatcherOutputState | read-write | mandatory | Value of a single output bit, 0-OFF, 1-ON. |
| 1.3.6.1.4.1.5040.1.2.27.1.6 | ScalarwtIpWatcherOutputValue | read-write | mandatory | This variable is used to read and write the outputs of the digital I/O port. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. B… |
| 1.3.6.1.4.1.5040.1.2.27.1.7 | ScalarwtIpWatcherSetOutput | read-write | mandatory | This variable allows setting of individual digital outputs. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds … |
| 1.3.6.1.4.1.5040.1.2.27.1.8 | TablewtIpWatcherAlarmOutputTable | not-accessible | mandatory | List of alarm indices.. |
| 1.3.6.1.4.1.5040.1.2.27.1.8.1 | RowwtIpWatcherAlarmOutputEntry | not-accessible | mandatory | Index reference. |
| 1.3.6.1.4.1.5040.1.2.27.1.8.1.1 | ColumnwtIpWatcherAlarmOutputState | read-write | mandatory | State of the alarm, 0-OFF, 1-ON. |
| 1.3.6.1.4.1.5040.1.2.27.1.8.1.2 | ColumnwtIpWatcherAlarmTriggerState | read-only | mandatory | State of the trigger condition, 0-OFF, 1-ON. |
| 1.3.6.1.4.1.5040.1.2.27.2 | NodewtIpWatcherSessCntrl | |||
| 1.3.6.1.4.1.5040.1.2.27.2.1 | ScalarwtIpWatcherSessCntrlPassword | read-write | mandatory | Entering this password opens a session which is ended by writing a 1 to wtIpWatcherSessCntrlLogout. When read this variable provides a string of length zero. |
| 1.3.6.1.4.1.5040.1.2.27.2.2 | ScalarwtIpWatcherSessCntrlConfigMode | read-only | mandatory | When the device is in SNMP configuration mode, the value 1 is returned, otherwise 0. If the read value is 0 even though the password was written, the device is… |
| 1.3.6.1.4.1.5040.1.2.27.2.3 | ScalarwtIpWatcherSessCntrlLogout | read-write | mandatory | If the device is in configuration mode and the session was opened by this SNMP Manager, writing a 1 to this variable will end the session and all parameters ar… |
| 1.3.6.1.4.1.5040.1.2.27.2.4 | ScalarwtIpWatcherSessCntrlAdminPassword | read-write | mandatory | This password protects access to the variables with administrator rights. It can only be changed by the administrator. If no password was assigned, the valid p… |
| 1.3.6.1.4.1.5040.1.2.27.2.5 | ScalarwtIpWatcherSessCntrlConfigPassword | read-write | mandatory | This password protects access to the variables with configurator rights. It can be changed by the administrator and by the configurator. If no password was ass… |
| 1.3.6.1.4.1.5040.1.2.27.3 | NodewtIpWatcherConfig | |||
| 1.3.6.1.4.1.5040.1.2.27.3.1 | NodewtIpWatcherDevice | |||
| 1.3.6.1.4.1.5040.1.2.27.3.1.1 | NodewtIpWatcherText | |||
| 1.3.6.1.4.1.5040.1.2.27.3.1.1.1 | ScalarwtIpWatcherDeviceName | read-write | mandatory | Name of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.1.2 | ScalarwtIpWatcherDeviceText | read-write | mandatory | Description of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.1.3 | ScalarwtIpWatcherDeviceLocation | read-write | mandatory | Description of the location of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.1.4 | ScalarwtIpWatcherDeviceContact | read-write | mandatory | Contact address of the system operator of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.2 | NodewtIpWatcherTimeDate | |||
| 1.3.6.1.4.1.5040.1.2.27.3.1.2.1 | NodewtIpWatcherTimeZone | |||
| 1.3.6.1.4.1.5040.1.2.27.3.1.2.1.1 | ScalarwtIpWatcherTzOffsetHrs | read-write | mandatory | Offset hours for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.2.1.2 | ScalarwtIpWatcherTzOffsetMin | read-write | mandatory | Offset minutes for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.2.1.3 | ScalarwtIpWatcherTzEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Timezone |
| 1.3.6.1.4.1.5040.1.2.27.3.1.2.1.4 | ScalarwtIpWatcherStTzOffsetHrs | read-write | mandatory | Offset hours of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.2.1.5 | ScalarwtIpWatcherStTzOffsetMin | read-write | mandatory | Offset minutes of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.2.1.6 | ScalarwtIpWatcherStTzEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Summertime |
| 1.3.6.1.4.1.5040.1.2.27.3.1.2.1.7 | ScalarwtIpWatcherStTzStartMonth | read-write | mandatory | Month in which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.2.1.8 | ScalarwtIpWatcherStTzStartMode | read-write | mandatory | Mode of the day of the week for which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.2.1.9 | ScalarwtIpWatcherStTzStartWday | read-write | mandatory | Day of the week on which the change is made from winter time to summer time |
| 1.3.6.1.4.1.5040.1.2.27.3.1.2.1.10 | ScalarwtIpWatcherStTzStartHrs | read-write | mandatory | Hour in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.2.1.11 | ScalarwtIpWatcherStTzStartMin | read-write | mandatory | Minute in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.2.1.12 | ScalarwtIpWatcherStTzStopMonth | read-write | mandatory | Month in which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.2.1.13 | ScalarwtIpWatcherStTzStopMode | read-write | mandatory | Mode of the week day on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.2.1.14 | ScalarwtIpWatcherStTzStopWday | read-write | mandatory | Day of the week on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.2.1.15 | ScalarwtIpWatcherStTzStopHrs | read-write | mandatory | Hour at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.2.1.16 | ScalarwtIpWatcherStTzStopMin | read-write | mandatory | Minute at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.2.2 | NodewtIpWatcherTimeServer | |||
| 1.3.6.1.4.1.5040.1.2.27.3.1.2.2.1 | ScalarwtIpWatcherTimeServer1 | read-write | mandatory | IP address or name of the 1st time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.27.3.1.2.2.2 | ScalarwtIpWatcherTimeServer2 | read-write | mandatory | IP address or name of the 2nd time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.27.3.1.2.2.3 | ScalarwtIpWatcherTsEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Time Server |
| 1.3.6.1.4.1.5040.1.2.27.3.1.2.2.4 | ScalarwtIpWatcherTsSyncTime | read-write | mandatory | Daily synchronisation time with the time server (hour: 0-23). |
| 1.3.6.1.4.1.5040.1.2.27.3.1.2.3 | NodewtIpWatcherDeviceClock | |||
| 1.3.6.1.4.1.5040.1.2.27.3.1.2.3.1 | ScalarwtIpWatcherClockHrs | read-write | mandatory | Clock hours taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.2.3.2 | ScalarwtIpWatcherClockMin | read-write | mandatory | Clock minutes taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.2.3.3 | ScalarwtIpWatcherClockDay | read-write | mandatory | Date: Day of the month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.2.3.4 | ScalarwtIpWatcherClockMonth | read-write | mandatory | Date: Month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.2.3.5 | ScalarwtIpWatcherClockYear | read-write | mandatory | Date: Year, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.3 | NodewtIpWatcherBasic | |||
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.1 | NodewtIpWatcherNetwork | |||
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.1.1 | ScalarwtIpWatcherIpAddress | read-write | mandatory | IP address of the Webio |
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.1.2 | ScalarwtIpWatcherSubnetMask | read-write | mandatory | Subnet mask of the Webio |
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.1.3 | ScalarwtIpWatcherGateway | read-write | mandatory | Gateway of the Webio |
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.1.4 | ScalarwtIpWatcherDnsServer1 | read-write | mandatory | IP address of the 1st DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.1.5 | ScalarwtIpWatcherDnsServer2 | read-write | mandatory | IP address of the 2nd DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.1.6 | ScalarwtIpWatcherAddConfig | read-write | mandatory | Additional configuration (1=ON): Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1: DHCP enable Bit 0: BOOTP enable |
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.2 | NodewtIpWatcherHTTP | |||
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.2.4 | ScalarwtIpWatcherHttpPort | read-write | mandatory | Definition of the standard HTML port (Default: 80). |
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.3 | NodewtIpWatcherMail | |||
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.3.1 | ScalarwtIpWatcherMailAdName | read-write | mandatory | Device name for mail administration. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.3.2 | ScalarwtIpWatcherMailReply | read-write | mandatory | Reply address for the mail server. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.3.3 | ScalarwtIpWatcherMailServer | read-write | mandatory | Name or IP address of the mail server. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.3.4 | ScalarwtIpWatcherMailEnable | read-write | mandatory | Set this bit to enable the sending of mails: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Mail enable |
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.3.5 | ScalarwtIpWatcherMailAuthentication | read-write | mandatory | Selection of the authentication modi: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTE… |
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.3.6 | ScalarwtIpWatcherMailAuthUser | read-write | mandatory | Name of the user to be authenticated. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.3.7 | ScalarwtIpWatcherMailAuthPassword | read-write | mandatory | Authentication password. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.3.8 | ScalarwtIpWatcherMailPop3Server | read-write | mandatory | Name or Ip-address of the POP3 Servers. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.4 | NodewtIpWatcherSNMP | |||
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.4.1 | ScalarwtIpWatcherSnmpEnable | read-write | mandatory | Set bit 0 to enable SNMP. If disabled, the device did not respond to any SNMP requests. Bit 1 decided wether the community string of read operations is compare… |
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.4.2 | ScalarwtIpWatcherSnmpCommunityStringRead | read-write | mandatory | Community string read only |
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.4.3 | ScalarwtIpWatcherSnmpCommunityStringReadWrite | read-write | mandatory | Community string read / write |
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.4.4 | ScalarwtIpWatcherSnmpSystemTrapManagerIP | read-write | mandatory | Name or IP address of the TCP server which accepts the system trap. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.4.5 | ScalarwtIpWatcherSnmpSystemTrapEnable | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2: Diag messages Bit 3-7: unused |
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.5 | NodewtIpWatcherUDP | |||
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.5.1 | ScalarwtIpWatcherUdpAdminPort | read-write | mandatory | Udp port to which the Udp queries ( short form GET requests) can be sent. This port number must be unique within the device. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.5.2 | ScalarwtIpWatcherUdpEnable | read-write | mandatory | Set this bit to enable UDP support: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : UDP enable |
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.5.3 | ScalarwtIpWatcherUdpRemotePort | read-write | mandatory | Udp remote port setting. If this value is set to zero, the source port read from a request will be used as destination port for the answer. A non zero value fo… |
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.7 | NodewtIpWatcherSyslog | |||
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.7.1 | ScalarwtIpWatcherSyslogServerIP | read-write | mandatory | Name or IP address of the Syslog server, which accepts the Syslog messgaes. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.7.2 | ScalarwtIpWatcherSyslogServerPort | read-write | mandatory | Portnumber of the Syslog servers, default 514. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.7.3 | ScalarwtIpWatcherSyslogSystemMessagesEnable | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2: Diag Messages Bit 3-7: unused |
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.7.4 | ScalarwtIpWatcherSyslogEnable | read-write | mandatory | Set bit 0to enable Syslog: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Syslog enable |
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.8 | NodewtIpWatcherFTP | |||
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.8.1 | ScalarwtIpWatcherFTPServerIP | read-write | mandatory | Name or IP address of the FTP server, which accepts the FTP messages. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.8.2 | ScalarwtIpWatcherFTPServerControlPort | read-write | mandatory | Portnumber of the control port of the FTP server, default 21. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.8.3 | ScalarwtIpWatcherFTPUserName | read-write | mandatory | FTP Loggin: user name. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.8.4 | ScalarwtIpWatcherFTPPassword | read-write | mandatory | FTP Loggin: user password. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.8.5 | ScalarwtIpWatcherFTPAccount | read-write | mandatory | FTP Loggin: name of account. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.8.6 | ScalarwtIpWatcherFTPOption | read-write | mandatory | Bit 0 switches the FTP Server in Passiv-Mode, the Client controls the data connection on its own: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit … |
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.8.7 | ScalarwtIpWatcherFTPEnable | read-write | mandatory | Set Bit 0 to enable FTP: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : FTP enable |
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.11 | NodewtIpWatcherIpList | |||
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.11.1 | ScalarwtIpWatcherIpListCount | read-only | mandatory | Number of Ip addresses. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.11.2 | TablewtIpWatcherIpListIfTable | not-accessible | mandatory | Table of inices. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.11.2.1 | RowwtIpWatcherIpListIfEntry | not-accessible | mandatory | Table entry. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.11.2.1.1 | ColumnwtIpWatcherIpListNo | read-only | mandatory | List number of this entry. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.11.3 | TablewtIpWatcherIpListTable | not-accessible | mandatory | List of ip addresses. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.11.3.1 | RowwtIpWatcherIpListEntry | not-accessible | mandatory | List entry. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.11.3.1.1 | ColumnwtIpWatcherIpListName | read-write | mandatory | Name or IP address. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.11.3.1.2 | ColumnwtIpWatcherIpListPort | read-write | mandatory | Port number, zero in the case of broadcast or Ping. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.11.3.1.3 | ColumnwtIpWatcherIpListService | read-write | mandatory | Binary coded scan mode, only one mode can be selected at a particular time: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Ping enable Bit 1-7… |
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.11.3.1.4 | ColumnwtIpWatcherIpListEnable | read-write | mandatory | Binary coded alarm enable: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: enabled in Alarm 1 Bit 1: enabled in Alarm 2 Bit 2: enabled in Alarm… |
| 1.3.6.1.4.1.5040.1.2.27.3.1.3.11.3.1.5 | ColumnwtIpWatcherIpListAlias | read-write | mandatory | Alias Name |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5 | NodewtIpWatcherAlarm | |||
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.1 | ScalarwtIpWatcherAlarmCount | read-only | mandatory | Number of independent alarms. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.2 | TablewtIpWatcherAlarmIfTable | not-accessible | mandatory | List of alarm indices. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.2.1 | RowwtIpWatcherAlarmIfEntry | not-accessible | mandatory | Numbers of the alarms. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.2.1.1 | ColumnwtIpWatcherAlarmNo | read-only | mandatory | Numbers of the alarms. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3 | TablewtIpWatcherAlarmTable | not-accessible | mandatory | List of settings depending on the alarm number. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1 | RowwtIpWatcherAlarmEntry | not-accessible | mandatory | Alarm parameters of the individual alarms. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.5 | ColumnwtIpWatcherAlarmInterval | read-write | mandatory | Send interval for alarm messages. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.6 | ColumnwtIpWatcherAlarmEnable | read-write | mandatory | Binary coded alarm enable: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Mail Enable Bit 1: SNMP Trap enable Bit 2: UDP enable Bit 3: Send in… |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.7 | ColumnwtIpWatcherAlarmMailAddr | read-write | mandatory | E-Mail address for sending the alarm mail to. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.8 | ColumnwtIpWatcherAlarmMailSubject | read-write | mandatory | Subject line for alarm mail. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.9 | ColumnwtIpWatcherAlarmMailText | read-write | mandatory | Alarm mail text: States of the Webio device can be included by using special tags. Please refer to the respective Webio manual |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.10 | ColumnwtIpWatcherAlarmSnmpManagerIP | read-write | mandatory | IP address of the SNMP Manager to which the Webio device should send SNMP traps. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.11 | ColumnwtIpWatcherAlarmSnmpTrapText | read-write | mandatory | This text appears in the trap body. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.12 | ColumnwtIpWatcherAlarmUdpIpAddr | read-write | mandatory | IP address of the UDP listener to which the Webio device should send UDP traps. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.13 | ColumnwtIpWatcherAlarmUdpPort | read-write | mandatory | Port number of the UDP listener to which the Webio device should send UDP traps. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.14 | ColumnwtIpWatcherAlarmUdpText | read-write | mandatory | This text appears in the UDP trap body. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.15 | ColumnwtIpWatcherAlarmTcpIpAddr | read-write | mandatory | IP address of the TCP listener to which the Webio device should send TCP traps. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.16 | ColumnwtIpWatcherAlarmTcpPort | read-write | mandatory | Port number of the TCP listener to which the Webio device should send TCP traps. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.17 | ColumnwtIpWatcherAlarmTcpText | read-write | mandatory | This text appears in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.18 | ColumnwtIpWatcherAlarmSyslogIpAddr | read-write | mandatory | IP address of the syslog server to which the Webio device should send syslog messages. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.19 | ColumnwtIpWatcherAlarmSyslogPort | read-write | mandatory | Port number of the syslog server to which the Webio device should send syslog messages. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.20 | ColumnwtIpWatcherAlarmSyslogText | read-write | mandatory | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.21 | ColumnwtIpWatcherAlarmFtpDataPort | read-write | mandatory | Local data port: 1..65535 or AUTO: the next free port will be assigned. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.22 | ColumnwtIpWatcherAlarmFtpFileName | read-write | mandatory | Name of the file including path informations. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.23 | ColumnwtIpWatcherAlarmFtpText | read-write | mandatory | Message text to store on the FTP server. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.24 | ColumnwtIpWatcherAlarmFtpOption | read-write | mandatory | Binary coded options, select only one option at the same time: STORE = replace file APPEND = append message at the end of the file Octet 1: unused Octet 2: unu… |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.25 | ColumnwtIpWatcherAlarmTimerCron | read-write | mandatory | This entry contains 5 space or tab seperated text fields for time trigger definition. Each field must match with the actual time to trigger a message, weekday … |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.26 | ColumnwtIpWatcherAlarmMailReleaseSubject | read-write | mandatory | Subject line for alarm mail. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.27 | ColumnwtIpWatcherAlarmMailReleaseText | read-write | mandatory | Release Alarm mail text: States of the Webio device can be included by using special tags. Please refer to the respective Webio manual |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.28 | ColumnwtIpWatcherAlarmSnmpTrapReleaseText | read-write | mandatory | This text appears in the trap body. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.29 | ColumnwtIpWatcherAlarmUdpReleaseText | read-write | mandatory | This text appears in the UDP trap body. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.30 | ColumnwtIpWatcherAlarmTcpReleaseText | read-write | mandatory | This text appears in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.31 | ColumnwtIpWatcherAlarmSyslogReleaseText | read-write | mandatory | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.32 | ColumnwtIpWatcherAlarmFtpReleaseText | read-write | mandatory | Message text to store on the FTP server. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.33 | ColumnwtIpWatcherAlarmName | read-write | mandatory | Name of the alarm. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.34 | ColumnwtIpWatcherAlarmGlobalEnable | read-write | mandatory | Binary coded alarm activation: Die OCTETS werden bitweise interpretiert. Bit 0 entspricht dem LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bit… |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.35 | ColumnwtIpWatcherAlarmCounterClear | read-write | mandatory | Binary coded options: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bit 2-7: un… |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.36 | ColumnwtIpWatcherAlarmAckEnable | read-write | mandatory | Binary coded options: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bit 2-7: un… |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.37 | ColumnwtIpWatcherAlarmAckPort | read-write | mandatory | Number of the input, which clears the alarm (1-6). |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.38 | ColumnwtIpWatcherAlarmSetPort | read-write | mandatory | Number of the output, which will be set by this alarm (1-6). The configuration of pulse mode and polarity defined in the port output section is used. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.39 | ColumnwtIpWatcherAlarmMailTrgClearSubject | read-write | mandatory | Subject line for alarm mail. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.40 | ColumnwtIpWatcherAlarmMailTrgClearText | read-write | mandatory | Alarm mail text: States of the Webio device can be included by using special tags. Please refer to the respective Webio manual |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.41 | ColumnwtIpWatcherAlarmSnmpTrapTrgClearText | read-write | mandatory | This text appears in the trap body. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.42 | ColumnwtIpWatcherAlarmUdpTrgClearText | read-write | mandatory | This text appears in the UDP trap body. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.43 | ColumnwtIpWatcherAlarmTcpTrgClearText | read-write | mandatory | This text appears in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.44 | ColumnwtIpWatcherAlarmSyslogTrgClearText | read-write | mandatory | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.45 | ColumnwtIpWatcherAlarmFtpTrgClearText | read-write | mandatory | Message text to store on the FTP server. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.46 | ColumnwtIpWatcherAlarmMailTrapTxEnable | read-write | mandatory | Binary coded options: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bit 4-7: un… |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.47 | ColumnwtIpWatcherAlarmSnmpTrapTrapTxEnable | read-write | mandatory | Binary coded options: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bit 4-7: un… |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.48 | ColumnwtIpWatcherAlarmUdpTrapTxEnable | read-write | mandatory | Binary coded options: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bit 4-7: un… |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.49 | ColumnwtIpWatcherAlarmTcpTrapTxEnable | read-write | mandatory | Binary coded options: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bit 4-7: un… |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.50 | ColumnwtIpWatcherAlarmSyslogTrapTxEnable | read-write | mandatory | Binary coded options: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bit 4-7: un… |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.51 | ColumnwtIpWatcherAlarmFtpTrapTxEnable | read-write | mandatory | Binary coded options: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bit 4-7: un… |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.52 | ColumnwtIpWatcherAlarmTriggerCount | read-write | mandatory | Alarm will be send if the trigger condition occours TriggerCount times. |
| 1.3.6.1.4.1.5040.1.2.27.3.1.5.3.1.53 | ColumnwtIpWatcherAlarmPollingRate | read-write | mandatory | Time in seconds. |
| 1.3.6.1.4.1.5040.1.2.27.3.2 | NodewtIpWatcherPorts | |||
| 1.3.6.1.4.1.5040.1.2.27.3.2.1 | TablewtIpWatcherInputPortTable | not-accessible | mandatory | List of settings depending on the input number. |
| 1.3.6.1.4.1.5040.1.2.27.3.2.1.1 | RowwtIpWatcherInputPortEntry | not-accessible | mandatory | Input parameter for the individual inputs. |
| 1.3.6.1.4.1.5040.1.2.27.3.2.1.1.1 | ColumnwtIpWatcherPortInputName | read-write | mandatory | Name of the input. |
| 1.3.6.1.4.1.5040.1.2.27.3.2.1.1.2 | ColumnwtIpWatcherPortInputText | read-write | mandatory | Description of the input. |
| 1.3.6.1.4.1.5040.1.2.27.3.2.1.1.4 | ColumnwtIpWatcherPortInputFilter | read-write | mandatory | Pulses with a duration shorter than here specified (duration in 1/1000 sec), are ignored. |
| 1.3.6.1.4.1.5040.1.2.27.3.2.2 | TablewtIpWatcherOutputPortTable | not-accessible | mandatory | List of settings depending on the output number. |
| 1.3.6.1.4.1.5040.1.2.27.3.2.2.1 | RowwtIpWatcherOutputPortEntry | not-accessible | mandatory | Output parameters of the individual outputs. |
| 1.3.6.1.4.1.5040.1.2.27.3.2.2.1.1 | ColumnwtIpWatcherPortOutputName | read-write | mandatory | Name of the output. |
| 1.3.6.1.4.1.5040.1.2.27.3.2.2.1.2 | ColumnwtIpWatcherPortOutputText | read-write | mandatory | Description of the output. |
| 1.3.6.1.4.1.5040.1.2.27.3.2.2.1.9 | ColumnwtIpWatcherPortPulseDuration | read-write | mandatory | Pulse length in 1/1000 sec. Setting this value to zero, disables the pulse output. |
| 1.3.6.1.4.1.5040.1.2.27.3.2.2.1.10 | ColumnwtIpWatcherPortPulsePolarity | read-write | mandatory | This value defines the polarity of the output pulse, if wtIpWatcherPortPulseDuration is not set to zero. After the pulse is finished, the output switches back … |
| 1.3.6.1.4.1.5040.1.2.27.3.3 | NodewtIpWatcherManufact | |||
| 1.3.6.1.4.1.5040.1.2.27.3.3.1 | ScalarwtIpWatcherMfName | read-write | mandatory | Manufacturer company name |
| 1.3.6.1.4.1.5040.1.2.27.3.3.2 | ScalarwtIpWatcherMfAddr | read-write | mandatory | Manufacturer address. |
| 1.3.6.1.4.1.5040.1.2.27.3.3.3 | ScalarwtIpWatcherMfHotline | read-write | mandatory | Manufacturer hotline. |
| 1.3.6.1.4.1.5040.1.2.27.3.3.4 | ScalarwtIpWatcherMfInternet | read-write | mandatory | Manufacturer Internet address. |
| 1.3.6.1.4.1.5040.1.2.27.3.3.5 | ScalarwtIpWatcherMfDeviceTyp | read-write | mandatory | Manufacturer device name (model number). |
| 1.3.6.1.4.1.5040.1.2.27.4 | NodewtIpWatcherDiag | |||
| 1.3.6.1.4.1.5040.1.2.27.4.1 | ScalarwtIpWatcherDiagErrorCount | read-only | mandatory | Number of entries in the error memory. |
| 1.3.6.1.4.1.5040.1.2.27.4.2 | ScalarwtIpWatcherDiagBinaryError | read-only | mandatory | Error causes coded bit-by-bit. |
| 1.3.6.1.4.1.5040.1.2.27.4.3 | ScalarwtIpWatcherDiagErrorIndex | read-write | mandatory | The value of this variable is used as an index to read an error massege from wtIpWatcherDiagErrorMessage. Errors are numbered from 1 to wtIpWatcherDiagErrorCou… |
| 1.3.6.1.4.1.5040.1.2.27.4.4 | ScalarwtIpWatcherDiagErrorMessage | read-only | mandatory | Using wtIpWatcherDiagErrorIndex as an index, the appropriate message is available. |
| 1.3.6.1.4.1.5040.1.2.27.4.5 | ScalarwtIpWatcherDiagErrorClear | write-only | mandatory | Writing 1 into this variable clears all diagnosis messages. |
| 1.3.6.1.4.1.5040.1.2.27.41 | NodewtIpWatcherAlert1 | This SNMP trap is generated when Alarm 1 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.27.42 | NodewtIpWatcherAlert2 | This SNMP trap is generated when Alarm 2 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.27.43 | NodewtIpWatcherAlert3 | This SNMP trap is generated when Alarm 3 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.27.44 | NodewtIpWatcherAlert4 | This SNMP trap is generated when Alarm 4 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.27.45 | NodewtIpWatcherAlert5 | This SNMP trap is generated when Alarm 5 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.27.46 | NodewtIpWatcherAlert6 | This SNMP trap is generated when Alarm 6 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.27.47 | NodewtIpWatcherAlert7 | This SNMP trap is generated when Alarm 7 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.27.48 | NodewtIpWatcherAlert8 | This SNMP trap is generated when Alarm 8 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.27.49 | NodewtIpWatcherAlert9 | This SNMP trap is generated when Alarm 9 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.27.50 | NodewtIpWatcherAlert10 | This SNMP trap is generated when Alarm 10 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.27.51 | NodewtIpWatcherAlert11 | This SNMP trap is generated when Alarm 11 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.27.52 | NodewtIpWatcherAlert12 | This SNMP trap is generated when Alarm 12 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.27.71 | NodewtIpWatcherAlert13 | This SNMP trap is generated when Alarm 1 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.27.72 | NodewtIpWatcherAlert14 | This SNMP trap is generated when Alarm 2 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.27.73 | NodewtIpWatcherAlert15 | This SNMP trap is generated when Alarm 3 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.27.74 | NodewtIpWatcherAlert16 | This SNMP trap is generated when Alarm 4 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.27.75 | NodewtIpWatcherAlert17 | This SNMP trap is generated when Alarm 5 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.27.76 | NodewtIpWatcherAlert18 | This SNMP trap is generated when Alarm 6 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.27.77 | NodewtIpWatcherAlert19 | This SNMP trap is generated when Alarm 7 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.27.78 | NodewtIpWatcherAlert20 | This SNMP trap is generated when Alarm 8 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.27.79 | NodewtIpWatcherAlert21 | This SNMP trap is generated when Alarm 9 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.27.80 | NodewtIpWatcherAlert22 | This SNMP trap is generated when Alarm 10 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.27.81 | NodewtIpWatcherAlert23 | This SNMP trap is generated when Alarm 11 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.27.82 | NodewtIpWatcherAlert24 | This SNMP trap is generated when Alarm 12 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.27.91 | NodewtIpWatcherAlert25 | This SNMP trap is generated when the trigger of the Alarm 1 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.27.92 | NodewtIpWatcherAlert26 | This SNMP trap is generated when the trigger of the Alarm 2 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.27.93 | NodewtIpWatcherAlert27 | This SNMP trap is generated when the trigger of the Alarm 3 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.27.94 | NodewtIpWatcherAlert28 | This SNMP trap is generated when the trigger of the Alarm 4 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.27.95 | NodewtIpWatcherAlert29 | This SNMP trap is generated when the trigger of the Alarm 5 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.27.96 | NodewtIpWatcherAlert30 | This SNMP trap is generated when the trigger of the Alarm 6 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.27.97 | NodewtIpWatcherAlert31 | This SNMP trap is generated when the trigger of the Alarm 7 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.27.98 | NodewtIpWatcherAlert32 | This SNMP trap is generated when the trigger of the Alarm 8 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.27.99 | NodewtIpWatcherAlert33 | This SNMP trap is generated when the trigger of the Alarm 9 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.27.100 | NodewtIpWatcherAlert34 | This SNMP trap is generated when the trigger of the Alarm 10 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.27.101 | NodewtIpWatcherAlert35 | This SNMP trap is generated when the trigger of the Alarm 11 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.27.102 | NodewtIpWatcherAlert36 | This SNMP trap is generated when the trigger of the Alarm 12 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.27.110 | NodewtIpWatcherAlertDiag | This SNMP trap is generated when a diagnosis/error message was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.30 | NodewtWebioEA2x2-24V | |||
| 1.3.6.1.4.1.5040.1.2.30.1 | NodewtWebioEA2x2-24VInOut | |||
| 1.3.6.1.4.1.5040.1.2.30.1.1 | ScalarwtWebioEA2x2-24VInputs | read-only | mandatory | Number of idependent inputs. |
| 1.3.6.1.4.1.5040.1.2.30.1.2 | ScalarwtWebioEA2x2-24VOutputs | read-only | mandatory | Number of idependent outputs. |
| 1.3.6.1.4.1.5040.1.2.30.1.3 | TablewtWebioEA2x2-24VInputTable | not-accessible | mandatory | List of input indices. |
| 1.3.6.1.4.1.5040.1.2.30.1.3.1 | RowwtWebioEA2x2-24VInputEntry | not-accessible | mandatory | Number of the inputs. |
| 1.3.6.1.4.1.5040.1.2.30.1.3.1.1 | ColumnwtWebioEA2x2-24VInputNo | read-only | mandatory | Index numbers of the inputs. |
| 1.3.6.1.4.1.5040.1.2.30.1.3.1.2 | ColumnwtWebioEA2x2-24VInputCounter | read-only | mandatory | Value of the input counter. |
| 1.3.6.1.4.1.5040.1.2.30.1.3.1.3 | ColumnwtWebioEA2x2-24VInputCounterClear | read-only | mandatory | Clears the input counter after returning its value. |
| 1.3.6.1.4.1.5040.1.2.30.1.3.1.4 | ColumnwtWebioEA2x2-24VInputState | read-only | mandatory | Value of a single input bit, 0-OFF, 1-ON. |
| 1.3.6.1.4.1.5040.1.2.30.1.4 | ScalarwtWebioEA2x2-24VInputValue | read-only | mandatory | This variable is used to read the inputs of the digital I/O port. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corres… |
| 1.3.6.1.4.1.5040.1.2.30.1.5 | TablewtWebioEA2x2-24VOutputTable | not-accessible | mandatory | List of output indices. |
| 1.3.6.1.4.1.5040.1.2.30.1.5.1 | RowwtWebioEA2x2-24VOutputEntry | not-accessible | mandatory | Number of the outputs. |
| 1.3.6.1.4.1.5040.1.2.30.1.5.1.1 | ColumnwtWebioEA2x2-24VOutputNo | read-only | mandatory | Output number. |
| 1.3.6.1.4.1.5040.1.2.30.1.5.1.2 | ColumnwtWebioEA2x2-24VOutputState | read-write | mandatory | Value of a single output bit, 0-OFF, 1-ON. |
| 1.3.6.1.4.1.5040.1.2.30.1.6 | ScalarwtWebioEA2x2-24VOutputValue | read-write | mandatory | This variable is used to read and write the outputs of the digital I/O port. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. B… |
| 1.3.6.1.4.1.5040.1.2.30.1.7 | ScalarwtWebioEA2x2-24VSetOutput | read-write | mandatory | This variable allows setting of individual digital outputs. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds … |
| 1.3.6.1.4.1.5040.1.2.30.2 | NodewtWebioEA2x2-24VSessCntrl | |||
| 1.3.6.1.4.1.5040.1.2.30.2.1 | ScalarwtWebioEA2x2-24VSessCntrlPassword | read-write | mandatory | Entering this password opens a session which is ended by writing a 1 to wtWebioEA2x2-24VSessCntrlLogout. When read this variable provides a string of length ze… |
| 1.3.6.1.4.1.5040.1.2.30.2.2 | ScalarwtWebioEA2x2-24VSessCntrlConfigMode | read-only | mandatory | When the device is in SNMP configuration mode, the value 1 is returned, otherwise 0. If the read value is 0 even though the password was written, the device is… |
| 1.3.6.1.4.1.5040.1.2.30.2.3 | ScalarwtWebioEA2x2-24VSessCntrlLogout | read-write | mandatory | If the device is in configuration mode and the session was opened by this SNMP Manager, writing a 1 to this variable will end the session and all parameters ar… |
| 1.3.6.1.4.1.5040.1.2.30.2.4 | ScalarwtWebioEA2x2-24VSessCntrlAdminPassword | read-write | mandatory | This password protects access to the variables with administrator rights. It can only be changed by the administrator. If no password was assigned, the valid p… |
| 1.3.6.1.4.1.5040.1.2.30.2.5 | ScalarwtWebioEA2x2-24VSessCntrlConfigPassword | read-write | mandatory | This password protects access to the variables with configurator rights. It can be changed by the administrator and by the configurator. If no password was ass… |
| 1.3.6.1.4.1.5040.1.2.30.3 | NodewtWebioEA2x2-24VConfig | |||
| 1.3.6.1.4.1.5040.1.2.30.3.1 | NodewtWebioEA2x2-24VDevice | |||
| 1.3.6.1.4.1.5040.1.2.30.3.1.1 | NodewtWebioEA2x2-24VText | |||
| 1.3.6.1.4.1.5040.1.2.30.3.1.1.1 | ScalarwtWebioEA2x2-24VDeviceName | read-write | mandatory | Name of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.1.2 | ScalarwtWebioEA2x2-24VDeviceText | read-write | mandatory | Description of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.1.3 | ScalarwtWebioEA2x2-24VDeviceLocation | read-write | mandatory | Description of the location of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.1.4 | ScalarwtWebioEA2x2-24VDeviceContact | read-write | mandatory | Contact address of the system operator of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.2 | NodewtWebioEA2x2-24VTimeDate | |||
| 1.3.6.1.4.1.5040.1.2.30.3.1.2.1 | NodewtWebioEA2x2-24VTimeZone | |||
| 1.3.6.1.4.1.5040.1.2.30.3.1.2.1.1 | ScalarwtWebioEA2x2-24VTzOffsetHrs | read-write | mandatory | Offset hours for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.2.1.2 | ScalarwtWebioEA2x2-24VTzOffsetMin | read-write | mandatory | Offset minutes for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.2.1.3 | ScalarwtWebioEA2x2-24VTzEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Timezone |
| 1.3.6.1.4.1.5040.1.2.30.3.1.2.1.4 | ScalarwtWebioEA2x2-24VStTzOffsetHrs | read-write | mandatory | Offset hours of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.2.1.5 | ScalarwtWebioEA2x2-24VStTzOffsetMin | read-write | mandatory | Offset minutes of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.2.1.6 | ScalarwtWebioEA2x2-24VStTzEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Summertime |
| 1.3.6.1.4.1.5040.1.2.30.3.1.2.1.7 | ScalarwtWebioEA2x2-24VStTzStartMonth | read-write | mandatory | Month in which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.2.1.8 | ScalarwtWebioEA2x2-24VStTzStartMode | read-write | mandatory | Mode of the day of the week for which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.2.1.9 | ScalarwtWebioEA2x2-24VStTzStartWday | read-write | mandatory | Day of the week on which the change is made from winter time to summer time |
| 1.3.6.1.4.1.5040.1.2.30.3.1.2.1.10 | ScalarwtWebioEA2x2-24VStTzStartHrs | read-write | mandatory | Hour in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.2.1.11 | ScalarwtWebioEA2x2-24VStTzStartMin | read-write | mandatory | Minute in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.2.1.12 | ScalarwtWebioEA2x2-24VStTzStopMonth | read-write | mandatory | Month in which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.2.1.13 | ScalarwtWebioEA2x2-24VStTzStopMode | read-write | mandatory | Mode of the week day on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.2.1.14 | ScalarwtWebioEA2x2-24VStTzStopWday | read-write | mandatory | Day of the week on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.2.1.15 | ScalarwtWebioEA2x2-24VStTzStopHrs | read-write | mandatory | Hour at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.2.1.16 | ScalarwtWebioEA2x2-24VStTzStopMin | read-write | mandatory | Minute at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.2.2 | NodewtWebioEA2x2-24VTimeServer | |||
| 1.3.6.1.4.1.5040.1.2.30.3.1.2.2.1 | ScalarwtWebioEA2x2-24VTimeServer1 | read-write | mandatory | IP address or name of the 1st time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.30.3.1.2.2.2 | ScalarwtWebioEA2x2-24VTimeServer2 | read-write | mandatory | IP address or name of the 2nd time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.30.3.1.2.2.3 | ScalarwtWebioEA2x2-24VTsEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Time Server |
| 1.3.6.1.4.1.5040.1.2.30.3.1.2.2.4 | ScalarwtWebioEA2x2-24VTsSyncTime | read-write | mandatory | Daily synchronisation time with the time server (hour: 0-23). |
| 1.3.6.1.4.1.5040.1.2.30.3.1.2.3 | NodewtWebioEA2x2-24VDeviceClock | |||
| 1.3.6.1.4.1.5040.1.2.30.3.1.2.3.1 | ScalarwtWebioEA2x2-24VClockHrs | read-write | mandatory | Clock hours taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.2.3.2 | ScalarwtWebioEA2x2-24VClockMin | read-write | mandatory | Clock minutes taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.2.3.3 | ScalarwtWebioEA2x2-24VClockDay | read-write | mandatory | Date: Day of the month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.2.3.4 | ScalarwtWebioEA2x2-24VClockMonth | read-write | mandatory | Date: Month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.2.3.5 | ScalarwtWebioEA2x2-24VClockYear | read-write | mandatory | Date: Year, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3 | NodewtWebioEA2x2-24VBasic | |||
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.1 | NodewtWebioEA2x2-24VNetwork | |||
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.1.1 | ScalarwtWebioEA2x2-24VIpAddress | read-write | mandatory | IP address of the Webio |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.1.2 | ScalarwtWebioEA2x2-24VSubnetMask | read-write | mandatory | Subnet mask of the Webio |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.1.3 | ScalarwtWebioEA2x2-24VGateway | read-write | mandatory | Gateway of the Webio |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.1.4 | ScalarwtWebioEA2x2-24VDnsServer1 | read-write | mandatory | IP address of the 1st DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.1.5 | ScalarwtWebioEA2x2-24VDnsServer2 | read-write | mandatory | IP address of the 2nd DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.1.6 | ScalarwtWebioEA2x2-24VAddConfig | read-write | mandatory | Additional configuration (1=ON): Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1: DHCP enable Bit 0: BOOTP enable |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.2 | NodewtWebioEA2x2-24VHTTP | |||
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.2.1 | ScalarwtWebioEA2x2-24VStartup | read-write | mandatory | Binary coded start page, more than one page must not be selected: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 2: user.htm Bit 1: home.htm Bit … |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.2.2 | ScalarwtWebioEA2x2-24VGetHeaderEnable | read-write | mandatory | If bits are set, every answer of a short form GET question will be lead by the IP-address and name of the device (Header) or a HTTP header (HTTP): Octet 1: unu… |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.2.3 | ScalarwtWebioEA2x2-24VHttpInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.2.4 | ScalarwtWebioEA2x2-24VHttpPort | read-write | mandatory | Definition of the standard HTML port (Default: 80). |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.3 | NodewtWebioEA2x2-24VMail | |||
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.3.1 | ScalarwtWebioEA2x2-24VMailAdName | read-write | mandatory | Device name for mail administration. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.3.2 | ScalarwtWebioEA2x2-24VMailReply | read-write | mandatory | Reply address for the mail server. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.3.3 | ScalarwtWebioEA2x2-24VMailServer | read-write | mandatory | Name or IP address of the mail server. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.3.4 | ScalarwtWebioEA2x2-24VMailEnable | read-write | mandatory | Set this bit to enable the sending of mails: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Mail enable |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.3.5 | ScalarwtWebioEA2x2-24VMailAuthentication | read-write | mandatory | Selection of the authentication modi: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTE… |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.3.6 | ScalarwtWebioEA2x2-24VMailAuthUser | read-write | mandatory | Name of the user to be authenticated. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.3.7 | ScalarwtWebioEA2x2-24VMailAuthPassword | read-write | mandatory | Authentication password. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.3.8 | ScalarwtWebioEA2x2-24VMailPop3Server | read-write | mandatory | Name or Ip-address of the POP3 Servers. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.4 | NodewtWebioEA2x2-24VSNMP | |||
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.4.1 | ScalarwtWebioEA2x2-24VSnmpEnable | read-write | mandatory | Set bit 0 to enable SNMP. If disabled, the device did not respond to any SNMP requests. Bit 1 decided wether the community string of read operations is compare… |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.4.2 | ScalarwtWebioEA2x2-24VSnmpCommunityStringRead | read-write | mandatory | Community string read only |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.4.3 | ScalarwtWebioEA2x2-24VSnmpCommunityStringReadWrite | read-write | mandatory | Community string read / write |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.4.4 | ScalarwtWebioEA2x2-24VSnmpSystemTrapManagerIP | read-write | mandatory | Name or IP address of the TCP server which accepts the system trap. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.4.5 | ScalarwtWebioEA2x2-24VSnmpSystemTrapEnable | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2: Diag messages Bit 3-7: unused |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.5 | NodewtWebioEA2x2-24VUDP | |||
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.5.1 | ScalarwtWebioEA2x2-24VUdpAdminPort | read-write | mandatory | Udp port to which the Udp queries ( short form GET requests) can be sent. This port number must be unique within the device. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.5.2 | ScalarwtWebioEA2x2-24VUdpEnable | read-write | mandatory | Set this bit to enable UDP support: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : UDP enable |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.5.3 | ScalarwtWebioEA2x2-24VUdpRemotePort | read-write | mandatory | Udp remote port setting. If this value is set to zero, the source port read from a request will be used as destination port for the answer. A non zero value fo… |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.6 | NodewtWebioEA2x2-24VBinary | |||
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.6.1 | ScalarwtWebioEA2x2-24VBinaryModeCount | read-only | mandatory | Number of independent binary channels. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.6.2 | TablewtWebioEA2x2-24VBinaryIfTable | not-accessible | mandatory | Table of indices. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.6.2.1 | RowwtWebioEA2x2-24VBinaryIfEntry | not-accessible | mandatory | Indices of the binary channels. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.6.2.1.1 | ColumnwtWebioEA2x2-24VBinaryModeNo | read-only | mandatory | Number of the binary channel. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3 | TablewtWebioEA2x2-24VBinaryTable | not-accessible | mandatory | Table of properties of the binary mode. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1 | RowwtWebioEA2x2-24VBinaryEntry | not-accessible | mandatory | Binary properties. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1.1 | ColumnwtWebioEA2x2-24VBinaryOperationMode | read-write | mandatory | Selection of the operation mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: … |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1.2 | ColumnwtWebioEA2x2-24VBinaryTcpServerLocalPort | read-write | mandatory | Local TCP port for data exchange in this server mode. This port number must be unique within the device. Reserved port number must not be used (refere to the m… |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1.3 | ColumnwtWebioEA2x2-24VBinaryTcpServerInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1.4 | ColumnwtWebioEA2x2-24VBinaryTcpServerApplicationMode | read-write | mandatory | Selection of the application mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4… |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1.5 | ColumnwtWebioEA2x2-24VBinaryTcpClientLocalPort | read-write | mandatory | Local TCP port for data exchange in this client mode. This port number must be unique within the device. Reserved port number must not be used (refere to the m… |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1.6 | ColumnwtWebioEA2x2-24VBinaryTcpClientServerPort | read-write | mandatory | Port number of the server. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when setting t… |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1.7 | ColumnwtWebioEA2x2-24VBinaryTcpClientServerIpAddr | read-write | mandatory | Ip address of the server. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when setting th… |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1.8 | ColumnwtWebioEA2x2-24VBinaryTcpClientServerPassword | read-write | mandatory | Building a connection may be protected by the administrator password of the server. Enter the server password to establish the connection, if a server administ… |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1.9 | ColumnwtWebioEA2x2-24VBinaryTcpClientInactivity | read-write | mandatory | Connection timeout in 100ms. If no data are exchanged within the specified time, the device closes the connection to the server. The value 0 deactivates the ti… |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1.10 | ColumnwtWebioEA2x2-24VBinaryTcpClientInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1.11 | ColumnwtWebioEA2x2-24VBinaryTcpClientInterval | read-write | mandatory | Configurable interval with a 100ms base, in which the Webio device sends data to the configured application. A interval of zero stopps the periodical sending. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1.12 | ColumnwtWebioEA2x2-24VBinaryTcpClientApplicationMode | read-write | mandatory | Selection of the application mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4… |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1.13 | ColumnwtWebioEA2x2-24VBinaryUdpPeerLocalPort | read-write | mandatory | Local UDP port for data exchange in this peer to peer mode. This port number must be unique within the device. Reserved port number must not be used (refere to… |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1.14 | ColumnwtWebioEA2x2-24VBinaryUdpPeerRemotePort | read-write | mandatory | Port number of the remote device. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when se… |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1.15 | ColumnwtWebioEA2x2-24VBinaryUdpPeerRemoteIpAddr | read-write | mandatory | Ip address of the remote device. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when set… |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1.16 | ColumnwtWebioEA2x2-24VBinaryUdpPeerInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1.17 | ColumnwtWebioEA2x2-24VBinaryUdpPeerInterval | read-write | mandatory | Configurable interval with a 100ms base, in which the Webio device sends data to the configured remote device. A interval of zero stopps the periodical sending. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1.18 | ColumnwtWebioEA2x2-24VBinaryUdpPeerApplicationMode | read-write | mandatory | Selection of the application mode: The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds to the LSB. OCTET 1: unus… |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1.19 | ColumnwtWebioEA2x2-24VBinaryConnectedPort | read-only | mandatory | Port number of the remote device, after connection has been established. In case of no connection or missing port informations a zero will be read. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1.20 | ColumnwtWebioEA2x2-24VBinaryConnectedIpAddr | read-only | mandatory | IP address of the remote device, after connection has been established. In case of no connection or missing port informations 0.0.0.0 will be read. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1.21 | ColumnwtWebioEA2x2-24VBinaryTcpServerClientHttpPort | read-write | mandatory | HTTP port number of the remote device at TCP Server Mode. If an mailfunction occurs status informations will be send to this port. Not used at mode Compatible … |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1.22 | ColumnwtWebioEA2x2-24VBinaryTcpClientServerHttpPort | read-write | mandatory | HTTP port number of the remote device at TCP Client Mode. In the operating mode Box2Box connection status informations will be exchanged through this port. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.7 | NodewtWebioEA2x2-24VSyslog | |||
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.7.1 | ScalarwtWebioEA2x2-24VSyslogServerIP | read-write | mandatory | Name or IP address of the Syslog server, which accepts the Syslog messgaes. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.7.2 | ScalarwtWebioEA2x2-24VSyslogServerPort | read-write | mandatory | Portnumber of the Syslog servers, default 514. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.7.3 | ScalarwtWebioEA2x2-24VSyslogSystemMessagesEnable | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2: Diag Messages Bit 3-7: unused |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.7.4 | ScalarwtWebioEA2x2-24VSyslogEnable | read-write | mandatory | Set bit 0to enable Syslog: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Syslog enable |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.8 | NodewtWebioEA2x2-24VFTP | |||
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.8.1 | ScalarwtWebioEA2x2-24VFTPServerIP | read-write | mandatory | Name or IP address of the FTP server, which accepts the FTP messages. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.8.2 | ScalarwtWebioEA2x2-24VFTPServerControlPort | read-write | mandatory | Portnumber of the control port of the FTP server, default 21. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.8.3 | ScalarwtWebioEA2x2-24VFTPUserName | read-write | mandatory | FTP Loggin: user name. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.8.4 | ScalarwtWebioEA2x2-24VFTPPassword | read-write | mandatory | FTP Loggin: user password. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.8.5 | ScalarwtWebioEA2x2-24VFTPAccount | read-write | mandatory | FTP Loggin: name of account. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.8.6 | ScalarwtWebioEA2x2-24VFTPOption | read-write | mandatory | Bit 0 switches the FTP Server in Passiv-Mode, the Client controls the data connection on its own: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit … |
| 1.3.6.1.4.1.5040.1.2.30.3.1.3.8.7 | ScalarwtWebioEA2x2-24VFTPEnable | read-write | mandatory | Set Bit 0 to enable FTP: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : FTP enable |
| 1.3.6.1.4.1.5040.1.2.30.3.1.4 | NodewtWebioEA2x2-24VOutputMode | |||
| 1.3.6.1.4.1.5040.1.2.30.3.1.4.1 | TablewtWebioEA2x2-24VOutputModeTable | not-accessible | mandatory | Table of output mode configurations dependent on the output indices. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.4.1.1 | RowwtWebioEA2x2-24VOutputModeEntry | not-accessible | mandatory | Output mode configurations of the individual outputs. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.4.1.1.1 | ColumnwtWebioEA2x2-24VOutputModeBit | read-write | mandatory | This binary coded output mode defines the individual operation mode for any output. More than one mode must not be selected. The OCTETS are interpreted bit-by-… |
| 1.3.6.1.4.1.5040.1.2.30.3.1.4.2 | ScalarwtWebioEA2x2-24VSafetyTimeout | read-write | mandatory | After this period of time (multiple of 100ms) without receiving data outputs switch to their Safety States. For each output a independend safety state could be… |
| 1.3.6.1.4.1.5040.1.2.30.3.1.4.4 | ScalarwtWebioEA2x2-24VPowerSupplyEnable | read-write | mandatory | Setting this enable bit turns on the intarnal 24V power supply of the outputs. All currents out must not exceed 150mA. At overcurrent condition the power suppl… |
| 1.3.6.1.4.1.5040.1.2.30.3.1.5 | NodewtWebioEA2x2-24VAlarm | |||
| 1.3.6.1.4.1.5040.1.2.30.3.1.5.1 | ScalarwtWebioEA2x2-24VAlarmCount | read-only | mandatory | Number of independent alarms. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.5.2 | TablewtWebioEA2x2-24VAlarmIfTable | not-accessible | mandatory | List of alarm indices. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.5.2.1 | RowwtWebioEA2x2-24VAlarmIfEntry | not-accessible | mandatory | Numbers of the alarms. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.5.2.1.1 | ColumnwtWebioEA2x2-24VAlarmNo | read-only | mandatory | Numbers of the alarms. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.5.3 | TablewtWebioEA2x2-24VAlarmTable | not-accessible | mandatory | List of settings depending on the alarm number. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.5.3.1 | RowwtWebioEA2x2-24VAlarmEntry | not-accessible | mandatory | Alarm parameters of the individual alarms. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.5.3.1.1 | ColumnwtWebioEA2x2-24VAlarmInputTrigger | read-write | mandatory | This variable allows setting of individual input trigger conditions. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an input. Bit 0 corr… |
| 1.3.6.1.4.1.5040.1.2.30.3.1.5.3.1.2 | ColumnwtWebioEA2x2-24VAlarmOutputTrigger | read-write | mandatory | This variable allows setting of individual output trigger conditions. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 co… |
| 1.3.6.1.4.1.5040.1.2.30.3.1.5.3.1.3 | ColumnwtWebioEA2x2-24VAlarmSystemTrigger | read-write | mandatory | Binary coded trigger conditions: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, … |
| 1.3.6.1.4.1.5040.1.2.30.3.1.5.3.1.4 | ColumnwtWebioEA2x2-24VAlarmMaxCounterValue | read-write | mandatory | This variable configures a max. counter value. If an input counter value exceeds this max. value, the corresponding alarm is triggered. Input counters with its… |
| 1.3.6.1.4.1.5040.1.2.30.3.1.5.3.1.5 | ColumnwtWebioEA2x2-24VAlarmInterval | read-write | mandatory | Send interval for alarm messages. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.5.3.1.6 | ColumnwtWebioEA2x2-24VAlarmEnable | read-write | mandatory | Binary coded alarm enable: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Mail Enable Bit 1: SNMP Trap enable Bit 2: UDP enable Bit 3: Send in… |
| 1.3.6.1.4.1.5040.1.2.30.3.1.5.3.1.7 | ColumnwtWebioEA2x2-24VAlarmMailAddr | read-write | mandatory | E-Mail address for sending the alarm mail to. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.5.3.1.8 | ColumnwtWebioEA2x2-24VAlarmMailSubject | read-write | mandatory | Subject line for alarm mail. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.5.3.1.9 | ColumnwtWebioEA2x2-24VAlarmMailText | read-write | mandatory | Alarm mail text: States of the Webio device can be included by using special tags. Please refer to the respective Webio manual |
| 1.3.6.1.4.1.5040.1.2.30.3.1.5.3.1.10 | ColumnwtWebioEA2x2-24VAlarmSnmpManagerIP | read-write | mandatory | IP address of the SNMP Manager to which the Webio device should send SNMP traps. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.5.3.1.11 | ColumnwtWebioEA2x2-24VAlarmSnmpTrapText | read-write | mandatory | This text appears in the trap body. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.5.3.1.12 | ColumnwtWebioEA2x2-24VAlarmUdpIpAddr | read-write | mandatory | IP address of the UDP listener to which the Webio device should send UDP traps. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.5.3.1.13 | ColumnwtWebioEA2x2-24VAlarmUdpPort | read-write | mandatory | Port number of the UDP listener to which the Webio device should send UDP traps. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.5.3.1.14 | ColumnwtWebioEA2x2-24VAlarmUdpText | read-write | mandatory | This text appears in the UDP trap body. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.5.3.1.15 | ColumnwtWebioEA2x2-24VAlarmTcpIpAddr | read-write | mandatory | IP address of the TCP listener to which the Webio device should send TCP traps. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.5.3.1.16 | ColumnwtWebioEA2x2-24VAlarmTcpPort | read-write | mandatory | Port number of the TCP listener to which the Webio device should send TCP traps. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.5.3.1.17 | ColumnwtWebioEA2x2-24VAlarmTcpText | read-write | mandatory | This text appears in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.5.3.1.18 | ColumnwtWebioEA2x2-24VAlarmSyslogIpAddr | read-write | mandatory | IP address of the syslog server to which the Webio device should send syslog messages. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.5.3.1.19 | ColumnwtWebioEA2x2-24VAlarmSyslogPort | read-write | mandatory | Port number of the syslog server to which the Webio device should send syslog messages. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.5.3.1.20 | ColumnwtWebioEA2x2-24VAlarmSyslogText | read-write | mandatory | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.5.3.1.21 | ColumnwtWebioEA2x2-24VAlarmFtpDataPort | read-write | mandatory | Local data port: 1..65535 or AUTO: the next free port will be assigned. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.5.3.1.22 | ColumnwtWebioEA2x2-24VAlarmFtpFileName | read-write | mandatory | Name of the file including path informations. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.5.3.1.23 | ColumnwtWebioEA2x2-24VAlarmFtpText | read-write | mandatory | Message text to store on the FTP server. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.5.3.1.24 | ColumnwtWebioEA2x2-24VAlarmFtpOption | read-write | mandatory | Binary coded options, select only one option at the same time: STORE = replace file APPEND = append message at the end of the file Octet 1: unused Octet 2: unu… |
| 1.3.6.1.4.1.5040.1.2.30.3.1.5.3.1.25 | ColumnwtWebioEA2x2-24VAlarmTimerCron | read-write | mandatory | This entry contains 5 space or tab seperated text fields for time trigger definition. Each field must match with the actual time to trigger a message, weekday … |
| 1.3.6.1.4.1.5040.1.2.30.3.1.5.3.1.26 | ColumnwtWebioEA2x2-24VAlarmMailReleaseSubject | read-write | mandatory | Subject line for alarm mail. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.5.3.1.27 | ColumnwtWebioEA2x2-24VAlarmMailReleaseText | read-write | mandatory | Release Alarm mail text: States of the Webio device can be included by using special tags. Please refer to the respective Webio manual |
| 1.3.6.1.4.1.5040.1.2.30.3.1.5.3.1.28 | ColumnwtWebioEA2x2-24VAlarmSnmpTrapReleaseText | read-write | mandatory | This text appears in the trap body. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.5.3.1.29 | ColumnwtWebioEA2x2-24VAlarmUdpReleaseText | read-write | mandatory | This text appears in the UDP trap body. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.5.3.1.30 | ColumnwtWebioEA2x2-24VAlarmTcpReleaseText | read-write | mandatory | This text appears in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.5.3.1.31 | ColumnwtWebioEA2x2-24VAlarmSyslogReleaseText | read-write | mandatory | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body. |
| 1.3.6.1.4.1.5040.1.2.30.3.1.5.3.1.32 | ColumnwtWebioEA2x2-24VAlarmFtpReleaseText | read-write | mandatory | Message text to store on the FTP server. |
| 1.3.6.1.4.1.5040.1.2.30.3.2 | NodewtWebioEA2x2-24VPorts | |||
| 1.3.6.1.4.1.5040.1.2.30.3.2.1 | TablewtWebioEA2x2-24VInputPortTable | not-accessible | mandatory | List of settings depending on the input number. |
| 1.3.6.1.4.1.5040.1.2.30.3.2.1.1 | RowwtWebioEA2x2-24VInputPortEntry | not-accessible | mandatory | Input parameter for the individual inputs. |
| 1.3.6.1.4.1.5040.1.2.30.3.2.1.1.1 | ColumnwtWebioEA2x2-24VPortInputName | read-write | mandatory | Name of the input. |
| 1.3.6.1.4.1.5040.1.2.30.3.2.1.1.2 | ColumnwtWebioEA2x2-24VPortInputText | read-write | mandatory | Description of the input. |
| 1.3.6.1.4.1.5040.1.2.30.3.2.1.1.3 | ColumnwtWebioEA2x2-24VPortInputMode | read-write | mandatory | Binary coded modes: Selecting short pulse detection enable by setting the corresponding bit to 1 enables interrupt support for counting. Only positive edges ar… |
| 1.3.6.1.4.1.5040.1.2.30.3.2.1.1.4 | ColumnwtWebioEA2x2-24VPortInputFilter | read-write | mandatory | Pulses with a duration shorter than here specified (duration in 1/1000 sec), are ignored. |
| 1.3.6.1.4.1.5040.1.2.30.3.2.1.1.5 | ColumnwtWebioEA2x2-24VPortInputBicountPulsePolarity | read-write | mandatory | This value defines the polarity of the input pulse. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 0 : negative polarity Bit 1 : positive polarit… |
| 1.3.6.1.4.1.5040.1.2.30.3.2.1.1.6 | ColumnwtWebioEA2x2-24VPortInputBicountInactivTimeout | read-write | mandatory | Pulse chains with a duration shorter than here specified (in 1/10 sek), are ignored. |
| 1.3.6.1.4.1.5040.1.2.30.3.2.2 | TablewtWebioEA2x2-24VOutputPortTable | not-accessible | mandatory | List of settings depending on the output number. |
| 1.3.6.1.4.1.5040.1.2.30.3.2.2.1 | RowwtWebioEA2x2-24VOutputPortEntry | not-accessible | mandatory | Output parameters of the individual outputs. |
| 1.3.6.1.4.1.5040.1.2.30.3.2.2.1.1 | ColumnwtWebioEA2x2-24VPortOutputName | read-write | mandatory | Name of the output. |
| 1.3.6.1.4.1.5040.1.2.30.3.2.2.1.2 | ColumnwtWebioEA2x2-24VPortOutputText | read-write | mandatory | Description of the output. |
| 1.3.6.1.4.1.5040.1.2.30.3.2.2.1.3 | ColumnwtWebioEA2x2-24VPortOutputGroupMode | read-write | mandatory | It is possible to connect outputs together to increase the output current. This could be done by connecting 2 or 4 outputs in a group together. All bits of suc… |
| 1.3.6.1.4.1.5040.1.2.30.3.2.2.1.4 | ColumnwtWebioEA2x2-24VPortOutputSafetyState | read-write | mandatory | This variable allows setting of individual digital outputs. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds … |
| 1.3.6.1.4.1.5040.1.2.30.3.2.2.1.5 | ColumnwtWebioEA2x2-24VPortLogicInputMask | read-write | mandatory | Selecting one of these inputs by setting the corresponding bit to 1 enables the logic function for the output identified by the index within this table. The ca… |
| 1.3.6.1.4.1.5040.1.2.30.3.2.2.1.6 | ColumnwtWebioEA2x2-24VPortLogicInputInverter | read-write | mandatory | Every input bit selected here will be inverted. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 0-1 : inputs 0-1 |
| 1.3.6.1.4.1.5040.1.2.30.3.2.2.1.7 | ColumnwtWebioEA2x2-24VPortLogicFunction | read-write | mandatory | This determines the logic function. No more than one function may be selected. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 0 : logic function … |
| 1.3.6.1.4.1.5040.1.2.30.3.2.2.1.8 | ColumnwtWebioEA2x2-24VPortLogicOutputInverter | read-write | mandatory | The logical operation result could be inverteted by setting the corresponding bit to 1. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 0 : Output… |
| 1.3.6.1.4.1.5040.1.2.30.3.2.2.1.9 | ColumnwtWebioEA2x2-24VPortPulseDuration | read-write | mandatory | Pulse length in 1/1000 sec. Setting this value to zero, disables the pulse output. |
| 1.3.6.1.4.1.5040.1.2.30.3.2.2.1.10 | ColumnwtWebioEA2x2-24VPortPulsePolarity | read-write | mandatory | This value defines the polarity of the output pulse, if wtWebioEA2x2-24VPortPulseDuration is not set to zero. After the pulse is finished, the output switches … |
| 1.3.6.1.4.1.5040.1.2.30.3.3 | NodewtWebioEA2x2-24VManufact | |||
| 1.3.6.1.4.1.5040.1.2.30.3.3.1 | ScalarwtWebioEA2x2-24VMfName | read-write | mandatory | Manufacturer company name |
| 1.3.6.1.4.1.5040.1.2.30.3.3.2 | ScalarwtWebioEA2x2-24VMfAddr | read-write | mandatory | Manufacturer address. |
| 1.3.6.1.4.1.5040.1.2.30.3.3.3 | ScalarwtWebioEA2x2-24VMfHotline | read-write | mandatory | Manufacturer hotline. |
| 1.3.6.1.4.1.5040.1.2.30.3.3.4 | ScalarwtWebioEA2x2-24VMfInternet | read-write | mandatory | Manufacturer Internet address. |
| 1.3.6.1.4.1.5040.1.2.30.3.3.5 | ScalarwtWebioEA2x2-24VMfDeviceTyp | read-write | mandatory | Manufacturer device name (model number). |
| 1.3.6.1.4.1.5040.1.2.30.4 | NodewtWebioEA2x2-24VDiag | |||
| 1.3.6.1.4.1.5040.1.2.30.4.1 | ScalarwtWebioEA2x2-24VDiagErrorCount | read-only | mandatory | Number of entries in the error memory. |
| 1.3.6.1.4.1.5040.1.2.30.4.2 | ScalarwtWebioEA2x2-24VDiagBinaryError | read-only | mandatory | Error causes coded bit-by-bit. |
| 1.3.6.1.4.1.5040.1.2.30.4.3 | ScalarwtWebioEA2x2-24VDiagErrorIndex | read-write | mandatory | The value of this variable is used as an index to read an error massege from wtWebioEA2x2-24VDiagErrorMessage. Errors are numbered from 1 to wtWebioEA2x2-24VDi… |
| 1.3.6.1.4.1.5040.1.2.30.4.4 | ScalarwtWebioEA2x2-24VDiagErrorMessage | read-only | mandatory | Using wtWebioEA2x2-24VDiagErrorIndex as an index, the appropriate message is available. |
| 1.3.6.1.4.1.5040.1.2.30.4.5 | ScalarwtWebioEA2x2-24VDiagErrorClear | write-only | mandatory | Writing 1 into this variable clears all diagnosis messages. |
| 1.3.6.1.4.1.5040.1.2.30.41 | NodewtWebioEA2x2-24VAlert1 | This SNMP trap is generated when Alarm 1 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.30.42 | NodewtWebioEA2x2-24VAlert2 | This SNMP trap is generated when Alarm 2 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.30.43 | NodewtWebioEA2x2-24VAlert3 | This SNMP trap is generated when Alarm 3 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.30.44 | NodewtWebioEA2x2-24VAlert4 | This SNMP trap is generated when Alarm 4 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.30.45 | NodewtWebioEA2x2-24VAlert5 | This SNMP trap is generated when Alarm 5 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.30.46 | NodewtWebioEA2x2-24VAlert6 | This SNMP trap is generated when Alarm 6 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.30.47 | NodewtWebioEA2x2-24VAlert7 | This SNMP trap is generated when Alarm 7 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.30.48 | NodewtWebioEA2x2-24VAlert8 | This SNMP trap is generated when Alarm 8 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.30.49 | NodewtWebioEA2x2-24VAlert9 | This SNMP trap is generated when Alarm 9 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.30.50 | NodewtWebioEA2x2-24VAlert10 | This SNMP trap is generated when Alarm 10 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.30.51 | NodewtWebioEA2x2-24VAlert11 | This SNMP trap is generated when Alarm 11 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.30.52 | NodewtWebioEA2x2-24VAlert12 | This SNMP trap is generated when Alarm 12 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.30.71 | NodewtWebioEA2x2-24VAlert13 | This SNMP trap is generated when Alarm 1 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.30.72 | NodewtWebioEA2x2-24VAlert14 | This SNMP trap is generated when Alarm 2 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.30.73 | NodewtWebioEA2x2-24VAlert15 | This SNMP trap is generated when Alarm 3 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.30.74 | NodewtWebioEA2x2-24VAlert16 | This SNMP trap is generated when Alarm 4 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.30.75 | NodewtWebioEA2x2-24VAlert17 | This SNMP trap is generated when Alarm 5 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.30.76 | NodewtWebioEA2x2-24VAlert18 | This SNMP trap is generated when Alarm 6 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.30.77 | NodewtWebioEA2x2-24VAlert19 | This SNMP trap is generated when Alarm 7 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.30.78 | NodewtWebioEA2x2-24VAlert20 | This SNMP trap is generated when Alarm 8 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.30.79 | NodewtWebioEA2x2-24VAlert21 | This SNMP trap is generated when Alarm 9 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.30.80 | NodewtWebioEA2x2-24VAlert22 | This SNMP trap is generated when Alarm 10 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.30.81 | NodewtWebioEA2x2-24VAlert23 | This SNMP trap is generated when Alarm 11 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.30.82 | NodewtWebioEA2x2-24VAlert24 | This SNMP trap is generated when Alarm 12 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.30.110 | NodewtWebioEA2x2-24VAlertDiag | This SNMP trap is generated when a diagnosis/error message was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.31 | NodewtWebioEA2x2ERP-24V | |||
| 1.3.6.1.4.1.5040.1.2.31.1 | NodewtWebioEA2x2ERP-24VInOut | |||
| 1.3.6.1.4.1.5040.1.2.31.1.1 | ScalarwtWebioEA2x2ERP-24VInputs | read-only | mandatory | Number of idependent inputs. |
| 1.3.6.1.4.1.5040.1.2.31.1.2 | ScalarwtWebioEA2x2ERP-24VOutputs | read-only | mandatory | Number of idependent outputs. |
| 1.3.6.1.4.1.5040.1.2.31.1.3 | TablewtWebioEA2x2ERP-24VInputTable | not-accessible | mandatory | List of input indices. |
| 1.3.6.1.4.1.5040.1.2.31.1.3.1 | RowwtWebioEA2x2ERP-24VInputEntry | not-accessible | mandatory | Number of the inputs. |
| 1.3.6.1.4.1.5040.1.2.31.1.3.1.1 | ColumnwtWebioEA2x2ERP-24VInputNo | read-only | mandatory | Index numbers of the inputs. |
| 1.3.6.1.4.1.5040.1.2.31.1.3.1.2 | ColumnwtWebioEA2x2ERP-24VInputCounter | read-only | mandatory | Value of the input counter. |
| 1.3.6.1.4.1.5040.1.2.31.1.3.1.3 | ColumnwtWebioEA2x2ERP-24VInputCounterClear | read-only | mandatory | Clears the input counter after returning its value. |
| 1.3.6.1.4.1.5040.1.2.31.1.3.1.4 | ColumnwtWebioEA2x2ERP-24VInputState | read-only | mandatory | Value of a single input bit, 0-OFF, 1-ON. |
| 1.3.6.1.4.1.5040.1.2.31.1.4 | ScalarwtWebioEA2x2ERP-24VInputValue | read-only | mandatory | This variable is used to read the inputs of the digital I/O port. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corres… |
| 1.3.6.1.4.1.5040.1.2.31.1.5 | TablewtWebioEA2x2ERP-24VOutputTable | not-accessible | mandatory | List of output indices. |
| 1.3.6.1.4.1.5040.1.2.31.1.5.1 | RowwtWebioEA2x2ERP-24VOutputEntry | not-accessible | mandatory | Number of the outputs. |
| 1.3.6.1.4.1.5040.1.2.31.1.5.1.1 | ColumnwtWebioEA2x2ERP-24VOutputNo | read-only | mandatory | Output number. |
| 1.3.6.1.4.1.5040.1.2.31.1.5.1.2 | ColumnwtWebioEA2x2ERP-24VOutputState | read-write | mandatory | Value of a single output bit, 0-OFF, 1-ON. |
| 1.3.6.1.4.1.5040.1.2.31.1.6 | ScalarwtWebioEA2x2ERP-24VOutputValue | read-write | mandatory | This variable is used to read and write the outputs of the digital I/O port. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. B… |
| 1.3.6.1.4.1.5040.1.2.31.1.7 | ScalarwtWebioEA2x2ERP-24VSetOutput | read-write | mandatory | This variable allows setting of individual digital outputs. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds … |
| 1.3.6.1.4.1.5040.1.2.31.2 | NodewtWebioEA2x2ERP-24VSessCntrl | |||
| 1.3.6.1.4.1.5040.1.2.31.2.1 | ScalarwtWebioEA2x2ERP-24VSessCntrlPassword | read-write | mandatory | Entering this password opens a session which is ended by writing a 1 to wtWebioEA2x2ERP-24VSessCntrlLogout. When read this variable provides a string of length… |
| 1.3.6.1.4.1.5040.1.2.31.2.2 | ScalarwtWebioEA2x2ERP-24VSessCntrlConfigMode | read-only | mandatory | When the device is in SNMP configuration mode, the value 1 is returned, otherwise 0. If the read value is 0 even though the password was written, the device is… |
| 1.3.6.1.4.1.5040.1.2.31.2.3 | ScalarwtWebioEA2x2ERP-24VSessCntrlLogout | read-write | mandatory | If the device is in configuration mode and the session was opened by this SNMP Manager, writing a 1 to this variable will end the session and all parameters ar… |
| 1.3.6.1.4.1.5040.1.2.31.2.4 | ScalarwtWebioEA2x2ERP-24VSessCntrlAdminPassword | read-write | mandatory | This password protects access to the variables with administrator rights. It can only be changed by the administrator. If no password was assigned, the valid p… |
| 1.3.6.1.4.1.5040.1.2.31.2.5 | ScalarwtWebioEA2x2ERP-24VSessCntrlConfigPassword | read-write | mandatory | This password protects access to the variables with configurator rights. It can be changed by the administrator and by the configurator. If no password was ass… |
| 1.3.6.1.4.1.5040.1.2.31.3 | NodewtWebioEA2x2ERP-24VConfig | |||
| 1.3.6.1.4.1.5040.1.2.31.3.1 | NodewtWebioEA2x2ERP-24VDevice | |||
| 1.3.6.1.4.1.5040.1.2.31.3.1.1 | NodewtWebioEA2x2ERP-24VText | |||
| 1.3.6.1.4.1.5040.1.2.31.3.1.1.1 | ScalarwtWebioEA2x2ERP-24VDeviceName | read-write | mandatory | Name of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.1.2 | ScalarwtWebioEA2x2ERP-24VDeviceText | read-write | mandatory | Description of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.1.3 | ScalarwtWebioEA2x2ERP-24VDeviceLocation | read-write | mandatory | Description of the location of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.1.4 | ScalarwtWebioEA2x2ERP-24VDeviceContact | read-write | mandatory | Contact address of the system operator of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.2 | NodewtWebioEA2x2ERP-24VTimeDate | |||
| 1.3.6.1.4.1.5040.1.2.31.3.1.2.1 | NodewtWebioEA2x2ERP-24VTimeZone | |||
| 1.3.6.1.4.1.5040.1.2.31.3.1.2.1.1 | ScalarwtWebioEA2x2ERP-24VTzOffsetHrs | read-write | mandatory | Offset hours for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.2.1.2 | ScalarwtWebioEA2x2ERP-24VTzOffsetMin | read-write | mandatory | Offset minutes for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.2.1.3 | ScalarwtWebioEA2x2ERP-24VTzEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Timezone |
| 1.3.6.1.4.1.5040.1.2.31.3.1.2.1.4 | ScalarwtWebioEA2x2ERP-24VStTzOffsetHrs | read-write | mandatory | Offset hours of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.2.1.5 | ScalarwtWebioEA2x2ERP-24VStTzOffsetMin | read-write | mandatory | Offset minutes of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.2.1.6 | ScalarwtWebioEA2x2ERP-24VStTzEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Summertime |
| 1.3.6.1.4.1.5040.1.2.31.3.1.2.1.7 | ScalarwtWebioEA2x2ERP-24VStTzStartMonth | read-write | mandatory | Month in which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.2.1.8 | ScalarwtWebioEA2x2ERP-24VStTzStartMode | read-write | mandatory | Mode of the day of the week for which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.2.1.9 | ScalarwtWebioEA2x2ERP-24VStTzStartWday | read-write | mandatory | Day of the week on which the change is made from winter time to summer time |
| 1.3.6.1.4.1.5040.1.2.31.3.1.2.1.10 | ScalarwtWebioEA2x2ERP-24VStTzStartHrs | read-write | mandatory | Hour in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.2.1.11 | ScalarwtWebioEA2x2ERP-24VStTzStartMin | read-write | mandatory | Minute in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.2.1.12 | ScalarwtWebioEA2x2ERP-24VStTzStopMonth | read-write | mandatory | Month in which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.2.1.13 | ScalarwtWebioEA2x2ERP-24VStTzStopMode | read-write | mandatory | Mode of the week day on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.2.1.14 | ScalarwtWebioEA2x2ERP-24VStTzStopWday | read-write | mandatory | Day of the week on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.2.1.15 | ScalarwtWebioEA2x2ERP-24VStTzStopHrs | read-write | mandatory | Hour at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.2.1.16 | ScalarwtWebioEA2x2ERP-24VStTzStopMin | read-write | mandatory | Minute at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.2.2 | NodewtWebioEA2x2ERP-24VTimeServer | |||
| 1.3.6.1.4.1.5040.1.2.31.3.1.2.2.1 | ScalarwtWebioEA2x2ERP-24VTimeServer1 | read-write | mandatory | IP address or name of the 1st time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.31.3.1.2.2.2 | ScalarwtWebioEA2x2ERP-24VTimeServer2 | read-write | mandatory | IP address or name of the 2nd time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.31.3.1.2.2.3 | ScalarwtWebioEA2x2ERP-24VTsEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Time Server |
| 1.3.6.1.4.1.5040.1.2.31.3.1.2.2.4 | ScalarwtWebioEA2x2ERP-24VTsSyncTime | read-write | mandatory | Daily synchronisation time with the time server (hour: 0-23). |
| 1.3.6.1.4.1.5040.1.2.31.3.1.2.3 | NodewtWebioEA2x2ERP-24VDeviceClock | |||
| 1.3.6.1.4.1.5040.1.2.31.3.1.2.3.1 | ScalarwtWebioEA2x2ERP-24VClockHrs | read-write | mandatory | Clock hours taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.2.3.2 | ScalarwtWebioEA2x2ERP-24VClockMin | read-write | mandatory | Clock minutes taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.2.3.3 | ScalarwtWebioEA2x2ERP-24VClockDay | read-write | mandatory | Date: Day of the month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.2.3.4 | ScalarwtWebioEA2x2ERP-24VClockMonth | read-write | mandatory | Date: Month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.2.3.5 | ScalarwtWebioEA2x2ERP-24VClockYear | read-write | mandatory | Date: Year, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3 | NodewtWebioEA2x2ERP-24VBasic | |||
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.1 | NodewtWebioEA2x2ERP-24VNetwork | |||
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.1.1 | ScalarwtWebioEA2x2ERP-24VIpAddress | read-write | mandatory | IP address of the Webio |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.1.2 | ScalarwtWebioEA2x2ERP-24VSubnetMask | read-write | mandatory | Subnet mask of the Webio |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.1.3 | ScalarwtWebioEA2x2ERP-24VGateway | read-write | mandatory | Gateway of the Webio |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.1.4 | ScalarwtWebioEA2x2ERP-24VDnsServer1 | read-write | mandatory | IP address of the 1st DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.1.5 | ScalarwtWebioEA2x2ERP-24VDnsServer2 | read-write | mandatory | IP address of the 2nd DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.1.6 | ScalarwtWebioEA2x2ERP-24VAddConfig | read-write | mandatory | Additional configuration (1=ON): Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1: DHCP enable Bit 0: BOOTP enable |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.2 | NodewtWebioEA2x2ERP-24VHTTP | |||
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.2.1 | ScalarwtWebioEA2x2ERP-24VStartup | read-write | mandatory | Binary coded start page, more than one page must not be selected: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 2: user.htm Bit 1: home.htm Bit … |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.2.2 | ScalarwtWebioEA2x2ERP-24VGetHeaderEnable | read-write | mandatory | If bits are set, every answer of a short form GET question will be lead by the IP-address and name of the device (Header) or a HTTP header (HTTP): Octet 1: unu… |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.2.3 | ScalarwtWebioEA2x2ERP-24VHttpInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.2.4 | ScalarwtWebioEA2x2ERP-24VHttpPort | read-write | mandatory | Definition of the standard HTML port (Default: 80). |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.3 | NodewtWebioEA2x2ERP-24VMail | |||
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.3.1 | ScalarwtWebioEA2x2ERP-24VMailAdName | read-write | mandatory | Device name for mail administration. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.3.2 | ScalarwtWebioEA2x2ERP-24VMailReply | read-write | mandatory | Reply address for the mail server. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.3.3 | ScalarwtWebioEA2x2ERP-24VMailServer | read-write | mandatory | Name or IP address of the mail server. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.3.4 | ScalarwtWebioEA2x2ERP-24VMailEnable | read-write | mandatory | Set this bit to enable the sending of mails: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Mail enable |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.3.5 | ScalarwtWebioEA2x2ERP-24VMailAuthentication | read-write | mandatory | Selection of the authentication modi: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTE… |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.3.6 | ScalarwtWebioEA2x2ERP-24VMailAuthUser | read-write | mandatory | Name of the user to be authenticated. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.3.7 | ScalarwtWebioEA2x2ERP-24VMailAuthPassword | read-write | mandatory | Authentication password. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.3.8 | ScalarwtWebioEA2x2ERP-24VMailPop3Server | read-write | mandatory | Name or Ip-address of the POP3 Servers. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.4 | NodewtWebioEA2x2ERP-24VSNMP | |||
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.4.1 | ScalarwtWebioEA2x2ERP-24VSnmpEnable | read-write | mandatory | Set bit 0 to enable SNMP. If disabled, the device did not respond to any SNMP requests. Bit 1 decided wether the community string of read operations is compare… |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.4.2 | ScalarwtWebioEA2x2ERP-24VSnmpCommunityStringRead | read-write | mandatory | Community string read only |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.4.3 | ScalarwtWebioEA2x2ERP-24VSnmpCommunityStringReadWrite | read-write | mandatory | Community string read / write |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.4.4 | ScalarwtWebioEA2x2ERP-24VSnmpSystemTrapManagerIP | read-write | mandatory | Name or IP address of the TCP server which accepts the system trap. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.4.5 | ScalarwtWebioEA2x2ERP-24VSnmpSystemTrapEnable | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2: Diag messages Bit 3-7: unused |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.5 | NodewtWebioEA2x2ERP-24VUDP | |||
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.5.1 | ScalarwtWebioEA2x2ERP-24VUdpAdminPort | read-write | mandatory | Udp port to which the Udp queries ( short form GET requests) can be sent. This port number must be unique within the device. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.5.2 | ScalarwtWebioEA2x2ERP-24VUdpEnable | read-write | mandatory | Set this bit to enable UDP support: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : UDP enable |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.5.3 | ScalarwtWebioEA2x2ERP-24VUdpRemotePort | read-write | mandatory | Udp remote port setting. If this value is set to zero, the source port read from a request will be used as destination port for the answer. A non zero value fo… |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.6 | NodewtWebioEA2x2ERP-24VBinary | |||
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.6.1 | ScalarwtWebioEA2x2ERP-24VBinaryModeCount | read-only | mandatory | Number of independent binary channels. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.6.2 | TablewtWebioEA2x2ERP-24VBinaryIfTable | not-accessible | mandatory | Table of indices. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.6.2.1 | RowwtWebioEA2x2ERP-24VBinaryIfEntry | not-accessible | mandatory | Indices of the binary channels. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.6.2.1.1 | ColumnwtWebioEA2x2ERP-24VBinaryModeNo | read-only | mandatory | Number of the binary channel. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.6.3 | TablewtWebioEA2x2ERP-24VBinaryTable | not-accessible | mandatory | Table of properties of the binary mode. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.6.3.1 | RowwtWebioEA2x2ERP-24VBinaryEntry | not-accessible | mandatory | Binary properties. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.6.3.1.1 | ColumnwtWebioEA2x2ERP-24VBinaryOperationMode | read-write | mandatory | Selection of the operation mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: … |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.6.3.1.2 | ColumnwtWebioEA2x2ERP-24VBinaryTcpServerLocalPort | read-write | mandatory | Local TCP port for data exchange in this server mode. This port number must be unique within the device. Reserved port number must not be used (refere to the m… |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.6.3.1.3 | ColumnwtWebioEA2x2ERP-24VBinaryTcpServerInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.6.3.1.4 | ColumnwtWebioEA2x2ERP-24VBinaryTcpServerApplicationMode | read-write | mandatory | Selection of the application mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4… |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.6.3.1.5 | ColumnwtWebioEA2x2ERP-24VBinaryTcpClientLocalPort | read-write | mandatory | Local TCP port for data exchange in this client mode. This port number must be unique within the device. Reserved port number must not be used (refere to the m… |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.6.3.1.6 | ColumnwtWebioEA2x2ERP-24VBinaryTcpClientServerPort | read-write | mandatory | Port number of the server. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when setting t… |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.6.3.1.7 | ColumnwtWebioEA2x2ERP-24VBinaryTcpClientServerIpAddr | read-write | mandatory | Ip address of the server. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when setting th… |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.6.3.1.8 | ColumnwtWebioEA2x2ERP-24VBinaryTcpClientServerPassword | read-write | mandatory | Building a connection may be protected by the administrator password of the server. Enter the server password to establish the connection, if a server administ… |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.6.3.1.9 | ColumnwtWebioEA2x2ERP-24VBinaryTcpClientInactivity | read-write | mandatory | Connection timeout in 100ms. If no data are exchanged within the specified time, the device closes the connection to the server. The value 0 deactivates the ti… |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.6.3.1.10 | ColumnwtWebioEA2x2ERP-24VBinaryTcpClientInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.6.3.1.11 | ColumnwtWebioEA2x2ERP-24VBinaryTcpClientInterval | read-write | mandatory | Configurable interval with a 100ms base, in which the Webio device sends data to the configured application. A interval of zero stopps the periodical sending. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.6.3.1.12 | ColumnwtWebioEA2x2ERP-24VBinaryTcpClientApplicationMode | read-write | mandatory | Selection of the application mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4… |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.6.3.1.13 | ColumnwtWebioEA2x2ERP-24VBinaryUdpPeerLocalPort | read-write | mandatory | Local UDP port for data exchange in this peer to peer mode. This port number must be unique within the device. Reserved port number must not be used (refere to… |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.6.3.1.14 | ColumnwtWebioEA2x2ERP-24VBinaryUdpPeerRemotePort | read-write | mandatory | Port number of the remote device. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when se… |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.6.3.1.15 | ColumnwtWebioEA2x2ERP-24VBinaryUdpPeerRemoteIpAddr | read-write | mandatory | Ip address of the remote device. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when set… |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.6.3.1.16 | ColumnwtWebioEA2x2ERP-24VBinaryUdpPeerInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.6.3.1.17 | ColumnwtWebioEA2x2ERP-24VBinaryUdpPeerInterval | read-write | mandatory | Configurable interval with a 100ms base, in which the Webio device sends data to the configured remote device. A interval of zero stopps the periodical sending. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.6.3.1.18 | ColumnwtWebioEA2x2ERP-24VBinaryUdpPeerApplicationMode | read-write | mandatory | Selection of the application mode: The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds to the LSB. OCTET 1: unus… |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.6.3.1.19 | ColumnwtWebioEA2x2ERP-24VBinaryConnectedPort | read-only | mandatory | Port number of the remote device, after connection has been established. In case of no connection or missing port informations a zero will be read. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.6.3.1.20 | ColumnwtWebioEA2x2ERP-24VBinaryConnectedIpAddr | read-only | mandatory | IP address of the remote device, after connection has been established. In case of no connection or missing port informations 0.0.0.0 will be read. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.6.3.1.21 | ColumnwtWebioEA2x2ERP-24VBinaryTcpServerClientHttpPort | read-write | mandatory | HTTP port number of the remote device at TCP Server Mode. If an mailfunction occurs status informations will be send to this port. Not used at mode Compatible … |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.6.3.1.22 | ColumnwtWebioEA2x2ERP-24VBinaryTcpClientServerHttpPort | read-write | mandatory | HTTP port number of the remote device at TCP Client Mode. In the operating mode Box2Box connection status informations will be exchanged through this port. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.7 | NodewtWebioEA2x2ERP-24VSyslog | |||
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.7.1 | ScalarwtWebioEA2x2ERP-24VSyslogServerIP | read-write | mandatory | Name or IP address of the Syslog server, which accepts the Syslog messgaes. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.7.2 | ScalarwtWebioEA2x2ERP-24VSyslogServerPort | read-write | mandatory | Portnumber of the Syslog servers, default 514. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.7.3 | ScalarwtWebioEA2x2ERP-24VSyslogSystemMessagesEnable | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2: Diag Messages Bit 3-7: unused |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.7.4 | ScalarwtWebioEA2x2ERP-24VSyslogEnable | read-write | mandatory | Set bit 0to enable Syslog: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Syslog enable |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.8 | NodewtWebioEA2x2ERP-24VFTP | |||
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.8.1 | ScalarwtWebioEA2x2ERP-24VFTPServerIP | read-write | mandatory | Name or IP address of the FTP server, which accepts the FTP messages. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.8.2 | ScalarwtWebioEA2x2ERP-24VFTPServerControlPort | read-write | mandatory | Portnumber of the control port of the FTP server, default 21. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.8.3 | ScalarwtWebioEA2x2ERP-24VFTPUserName | read-write | mandatory | FTP Loggin: user name. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.8.4 | ScalarwtWebioEA2x2ERP-24VFTPPassword | read-write | mandatory | FTP Loggin: user password. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.8.5 | ScalarwtWebioEA2x2ERP-24VFTPAccount | read-write | mandatory | FTP Loggin: name of account. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.8.6 | ScalarwtWebioEA2x2ERP-24VFTPOption | read-write | mandatory | Bit 0 switches the FTP Server in Passiv-Mode, the Client controls the data connection on its own: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit … |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.8.7 | ScalarwtWebioEA2x2ERP-24VFTPEnable | read-write | mandatory | Set Bit 0 to enable FTP: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : FTP enable |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.10 | NodewtWebioEA2x2ERP-24VWayBack | |||
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.10.1 | ScalarwtWebioEA2x2ERP-24VWayBackEnable | read-write | mandatory | Set Bit 0 to enable WayBack: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : WayBack enable |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.10.2 | ScalarwtWebioEA2x2ERP-24VWayBackServerControlPort | read-write | mandatory | Portnumber of the control port of the FTP server, default 21. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.10.3 | ScalarwtWebioEA2x2ERP-24VWayBackFTPPassword | read-write | mandatory | WayBack FTP Loggin: Password of the user. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.10.4 | ScalarwtWebioEA2x2ERP-24VWayBackFTPResponse | read-write | mandatory | WayBack FTP response: return message after login. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.3.10.5 | ScalarwtWebioEA2x2ERP-24VWayBackFTPTimeOut | read-write | mandatory | WayBack FTP Timeout: a request must be finished within this periode of time. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.4 | NodewtWebioEA2x2ERP-24VOutputMode | |||
| 1.3.6.1.4.1.5040.1.2.31.3.1.4.1 | TablewtWebioEA2x2ERP-24VOutputModeTable | not-accessible | mandatory | Table of output mode configurations dependent on the output indices. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.4.1.1 | RowwtWebioEA2x2ERP-24VOutputModeEntry | not-accessible | mandatory | Output mode configurations of the individual outputs. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.4.1.1.1 | ColumnwtWebioEA2x2ERP-24VOutputModeBit | read-write | mandatory | This binary coded output mode defines the individual operation mode for any output. More than one mode must not be selected. The OCTETS are interpreted bit-by-… |
| 1.3.6.1.4.1.5040.1.2.31.3.1.4.2 | ScalarwtWebioEA2x2ERP-24VSafetyTimeout | read-write | mandatory | After this period of time (multiple of 100ms) without receiving data outputs switch to their Safety States. For each output a independend safety state could be… |
| 1.3.6.1.4.1.5040.1.2.31.3.1.4.3 | ScalarwtWebioEA2x2ERP-24VLoadControlEnable | read-write | mandatory | Here the function of automatic load control can be enabled. All output were tested in pairs (0-1). If an error occours at one output, both output of an pair wi… |
| 1.3.6.1.4.1.5040.1.2.31.3.1.4.4 | ScalarwtWebioEA2x2ERP-24VPowerSupplyEnable | read-write | mandatory | Setting this enable bit turns on the intarnal 24V power supply of the outputs. All currents out must not exceed 150mA. At overcurrent condition the power suppl… |
| 1.3.6.1.4.1.5040.1.2.31.3.1.5 | NodewtWebioEA2x2ERP-24VAlarm | |||
| 1.3.6.1.4.1.5040.1.2.31.3.1.5.1 | ScalarwtWebioEA2x2ERP-24VAlarmCount | read-only | mandatory | Number of independent alarms. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.5.2 | TablewtWebioEA2x2ERP-24VAlarmIfTable | not-accessible | mandatory | List of alarm indices. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.5.2.1 | RowwtWebioEA2x2ERP-24VAlarmIfEntry | not-accessible | mandatory | Numbers of the alarms. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.5.2.1.1 | ColumnwtWebioEA2x2ERP-24VAlarmNo | read-only | mandatory | Numbers of the alarms. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.5.3 | TablewtWebioEA2x2ERP-24VAlarmTable | not-accessible | mandatory | List of settings depending on the alarm number. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.5.3.1 | RowwtWebioEA2x2ERP-24VAlarmEntry | not-accessible | mandatory | Alarm parameters of the individual alarms. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.5.3.1.1 | ColumnwtWebioEA2x2ERP-24VAlarmInputTrigger | read-write | mandatory | This variable allows setting of individual input trigger conditions. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an input. Bit 0 corr… |
| 1.3.6.1.4.1.5040.1.2.31.3.1.5.3.1.2 | ColumnwtWebioEA2x2ERP-24VAlarmOutputTrigger | read-write | mandatory | This variable allows setting of individual output trigger conditions. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 co… |
| 1.3.6.1.4.1.5040.1.2.31.3.1.5.3.1.3 | ColumnwtWebioEA2x2ERP-24VAlarmSystemTrigger | read-write | mandatory | Binary coded trigger conditions: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, … |
| 1.3.6.1.4.1.5040.1.2.31.3.1.5.3.1.4 | ColumnwtWebioEA2x2ERP-24VAlarmMaxCounterValue | read-write | mandatory | This variable configures a max. counter value. If an input counter value exceeds this max. value, the corresponding alarm is triggered. Input counters with its… |
| 1.3.6.1.4.1.5040.1.2.31.3.1.5.3.1.5 | ColumnwtWebioEA2x2ERP-24VAlarmInterval | read-write | mandatory | Send interval for alarm messages. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.5.3.1.6 | ColumnwtWebioEA2x2ERP-24VAlarmEnable | read-write | mandatory | Binary coded alarm enable: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Mail Enable Bit 1: SNMP Trap enable Bit 2: UDP enable Bit 3: Send in… |
| 1.3.6.1.4.1.5040.1.2.31.3.1.5.3.1.7 | ColumnwtWebioEA2x2ERP-24VAlarmMailAddr | read-write | mandatory | E-Mail address for sending the alarm mail to. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.5.3.1.8 | ColumnwtWebioEA2x2ERP-24VAlarmMailSubject | read-write | mandatory | Subject line for alarm mail. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.5.3.1.9 | ColumnwtWebioEA2x2ERP-24VAlarmMailText | read-write | mandatory | Alarm mail text: States of the Webio device can be included by using special tags. Please refer to the respective Webio manual |
| 1.3.6.1.4.1.5040.1.2.31.3.1.5.3.1.10 | ColumnwtWebioEA2x2ERP-24VAlarmSnmpManagerIP | read-write | mandatory | IP address of the SNMP Manager to which the Webio device should send SNMP traps. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.5.3.1.11 | ColumnwtWebioEA2x2ERP-24VAlarmSnmpTrapText | read-write | mandatory | This text appears in the trap body. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.5.3.1.12 | ColumnwtWebioEA2x2ERP-24VAlarmUdpIpAddr | read-write | mandatory | IP address of the UDP listener to which the Webio device should send UDP traps. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.5.3.1.13 | ColumnwtWebioEA2x2ERP-24VAlarmUdpPort | read-write | mandatory | Port number of the UDP listener to which the Webio device should send UDP traps. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.5.3.1.14 | ColumnwtWebioEA2x2ERP-24VAlarmUdpText | read-write | mandatory | This text appears in the UDP trap body. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.5.3.1.15 | ColumnwtWebioEA2x2ERP-24VAlarmTcpIpAddr | read-write | mandatory | IP address of the TCP listener to which the Webio device should send TCP traps. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.5.3.1.16 | ColumnwtWebioEA2x2ERP-24VAlarmTcpPort | read-write | mandatory | Port number of the TCP listener to which the Webio device should send TCP traps. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.5.3.1.17 | ColumnwtWebioEA2x2ERP-24VAlarmTcpText | read-write | mandatory | This text appears in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.5.3.1.18 | ColumnwtWebioEA2x2ERP-24VAlarmSyslogIpAddr | read-write | mandatory | IP address of the syslog server to which the Webio device should send syslog messages. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.5.3.1.19 | ColumnwtWebioEA2x2ERP-24VAlarmSyslogPort | read-write | mandatory | Port number of the syslog server to which the Webio device should send syslog messages. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.5.3.1.20 | ColumnwtWebioEA2x2ERP-24VAlarmSyslogText | read-write | mandatory | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.5.3.1.21 | ColumnwtWebioEA2x2ERP-24VAlarmFtpDataPort | read-write | mandatory | Local data port: 1..65535 or AUTO: the next free port will be assigned. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.5.3.1.22 | ColumnwtWebioEA2x2ERP-24VAlarmFtpFileName | read-write | mandatory | Name of the file including path informations. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.5.3.1.23 | ColumnwtWebioEA2x2ERP-24VAlarmFtpText | read-write | mandatory | Message text to store on the FTP server. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.5.3.1.24 | ColumnwtWebioEA2x2ERP-24VAlarmFtpOption | read-write | mandatory | Binary coded options, select only one option at the same time: STORE = replace file APPEND = append message at the end of the file Octet 1: unused Octet 2: unu… |
| 1.3.6.1.4.1.5040.1.2.31.3.1.5.3.1.25 | ColumnwtWebioEA2x2ERP-24VAlarmTimerCron | read-write | mandatory | This entry contains 5 space or tab seperated text fields for time trigger definition. Each field must match with the actual time to trigger a message, weekday … |
| 1.3.6.1.4.1.5040.1.2.31.3.1.5.3.1.26 | ColumnwtWebioEA2x2ERP-24VAlarmMailReleaseSubject | read-write | mandatory | Subject line for alarm mail. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.5.3.1.27 | ColumnwtWebioEA2x2ERP-24VAlarmMailReleaseText | read-write | mandatory | Release Alarm mail text: States of the Webio device can be included by using special tags. Please refer to the respective Webio manual |
| 1.3.6.1.4.1.5040.1.2.31.3.1.5.3.1.28 | ColumnwtWebioEA2x2ERP-24VAlarmSnmpTrapReleaseText | read-write | mandatory | This text appears in the trap body. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.5.3.1.29 | ColumnwtWebioEA2x2ERP-24VAlarmUdpReleaseText | read-write | mandatory | This text appears in the UDP trap body. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.5.3.1.30 | ColumnwtWebioEA2x2ERP-24VAlarmTcpReleaseText | read-write | mandatory | This text appears in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.5.3.1.31 | ColumnwtWebioEA2x2ERP-24VAlarmSyslogReleaseText | read-write | mandatory | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.5.3.1.32 | ColumnwtWebioEA2x2ERP-24VAlarmFtpReleaseText | read-write | mandatory | Message text to store on the FTP server. |
| 1.3.6.1.4.1.5040.1.2.31.3.1.5.4 | ScalarwtWebioEA2x2ERP-24VLoadControlView | read-only | mandatory | Here the result of automatic load control can be read. All output were tested in pairs (0-1). If an error occours at one output, both output of an pair will be… |
| 1.3.6.1.4.1.5040.1.2.31.3.1.5.5 | ScalarwtWebioEA2x2ERP-24VLCShutDownView | read-write | mandatory | Here the result of the automatic load control shut down can be read. All outputs remain switched of, until a zero is written into this variable. But previously… |
| 1.3.6.1.4.1.5040.1.2.31.3.2 | NodewtWebioEA2x2ERP-24VPorts | |||
| 1.3.6.1.4.1.5040.1.2.31.3.2.1 | TablewtWebioEA2x2ERP-24VInputPortTable | not-accessible | mandatory | List of settings depending on the input number. |
| 1.3.6.1.4.1.5040.1.2.31.3.2.1.1 | RowwtWebioEA2x2ERP-24VInputPortEntry | not-accessible | mandatory | Input parameter for the individual inputs. |
| 1.3.6.1.4.1.5040.1.2.31.3.2.1.1.1 | ColumnwtWebioEA2x2ERP-24VPortInputName | read-write | mandatory | Name of the input. |
| 1.3.6.1.4.1.5040.1.2.31.3.2.1.1.2 | ColumnwtWebioEA2x2ERP-24VPortInputText | read-write | mandatory | Description of the input. |
| 1.3.6.1.4.1.5040.1.2.31.3.2.1.1.3 | ColumnwtWebioEA2x2ERP-24VPortInputMode | read-write | mandatory | Binary coded modes: Selecting short pulse detection enable by setting the corresponding bit to 1 enables interrupt support for counting. Only positive edges ar… |
| 1.3.6.1.4.1.5040.1.2.31.3.2.1.1.4 | ColumnwtWebioEA2x2ERP-24VPortInputFilter | read-write | mandatory | Pulses with a duration shorter than here specified (duration in 1/1000 sec), are ignored. |
| 1.3.6.1.4.1.5040.1.2.31.3.2.1.1.5 | ColumnwtWebioEA2x2ERP-24VPortInputBicountPulsePolarity | read-write | mandatory | This value defines the polarity of the input pulse. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 0 : negative polarity Bit 1 : positive polarit… |
| 1.3.6.1.4.1.5040.1.2.31.3.2.1.1.6 | ColumnwtWebioEA2x2ERP-24VPortInputBicountInactivTimeout | read-write | mandatory | Pulse chains with a duration shorter than here specified (in 1/10 sek), are ignored. |
| 1.3.6.1.4.1.5040.1.2.31.3.2.2 | TablewtWebioEA2x2ERP-24VOutputPortTable | not-accessible | mandatory | List of settings depending on the output number. |
| 1.3.6.1.4.1.5040.1.2.31.3.2.2.1 | RowwtWebioEA2x2ERP-24VOutputPortEntry | not-accessible | mandatory | Output parameters of the individual outputs. |
| 1.3.6.1.4.1.5040.1.2.31.3.2.2.1.1 | ColumnwtWebioEA2x2ERP-24VPortOutputName | read-write | mandatory | Name of the output. |
| 1.3.6.1.4.1.5040.1.2.31.3.2.2.1.2 | ColumnwtWebioEA2x2ERP-24VPortOutputText | read-write | mandatory | Description of the output. |
| 1.3.6.1.4.1.5040.1.2.31.3.2.2.1.3 | ColumnwtWebioEA2x2ERP-24VPortOutputGroupMode | read-write | mandatory | It is possible to connect outputs together to increase the output current. This could be done by connecting 2 or 4 outputs in a group together. All bits of suc… |
| 1.3.6.1.4.1.5040.1.2.31.3.2.2.1.4 | ColumnwtWebioEA2x2ERP-24VPortOutputSafetyState | read-write | mandatory | This variable allows setting of individual digital outputs. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds … |
| 1.3.6.1.4.1.5040.1.2.31.3.2.2.1.5 | ColumnwtWebioEA2x2ERP-24VPortLogicInputMask | read-write | mandatory | Selecting one of these inputs by setting the corresponding bit to 1 enables the logic function for the output identified by the index within this table. The ca… |
| 1.3.6.1.4.1.5040.1.2.31.3.2.2.1.6 | ColumnwtWebioEA2x2ERP-24VPortLogicInputInverter | read-write | mandatory | Every input bit selected here will be inverted. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 0-1 : inputs 0-1 |
| 1.3.6.1.4.1.5040.1.2.31.3.2.2.1.7 | ColumnwtWebioEA2x2ERP-24VPortLogicFunction | read-write | mandatory | This determines the logic function. No more than one function may be selected. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 0 : logic function … |
| 1.3.6.1.4.1.5040.1.2.31.3.2.2.1.8 | ColumnwtWebioEA2x2ERP-24VPortLogicOutputInverter | read-write | mandatory | The logical operation result could be inverteted by setting the corresponding bit to 1. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 0 : Output… |
| 1.3.6.1.4.1.5040.1.2.31.3.2.2.1.9 | ColumnwtWebioEA2x2ERP-24VPortPulseDuration | read-write | mandatory | Pulse length in 1/1000 sec. Setting this value to zero, disables the pulse output. |
| 1.3.6.1.4.1.5040.1.2.31.3.2.2.1.10 | ColumnwtWebioEA2x2ERP-24VPortPulsePolarity | read-write | mandatory | This value defines the polarity of the output pulse, if wtWebioEA2x2ERP-24VPortPulseDuration is not set to zero. After the pulse is finished, the output switch… |
| 1.3.6.1.4.1.5040.1.2.31.3.3 | NodewtWebioEA2x2ERP-24VManufact | |||
| 1.3.6.1.4.1.5040.1.2.31.3.3.1 | ScalarwtWebioEA2x2ERP-24VMfName | read-write | mandatory | Manufacturer company name |
| 1.3.6.1.4.1.5040.1.2.31.3.3.2 | ScalarwtWebioEA2x2ERP-24VMfAddr | read-write | mandatory | Manufacturer address. |
| 1.3.6.1.4.1.5040.1.2.31.3.3.3 | ScalarwtWebioEA2x2ERP-24VMfHotline | read-write | mandatory | Manufacturer hotline. |
| 1.3.6.1.4.1.5040.1.2.31.3.3.4 | ScalarwtWebioEA2x2ERP-24VMfInternet | read-write | mandatory | Manufacturer Internet address. |
| 1.3.6.1.4.1.5040.1.2.31.3.3.5 | ScalarwtWebioEA2x2ERP-24VMfDeviceTyp | read-write | mandatory | Manufacturer device name (model number). |
| 1.3.6.1.4.1.5040.1.2.31.4 | NodewtWebioEA2x2ERP-24VDiag | |||
| 1.3.6.1.4.1.5040.1.2.31.4.1 | ScalarwtWebioEA2x2ERP-24VDiagErrorCount | read-only | mandatory | Number of entries in the error memory. |
| 1.3.6.1.4.1.5040.1.2.31.4.2 | ScalarwtWebioEA2x2ERP-24VDiagBinaryError | read-only | mandatory | Error causes coded bit-by-bit. |
| 1.3.6.1.4.1.5040.1.2.31.4.3 | ScalarwtWebioEA2x2ERP-24VDiagErrorIndex | read-write | mandatory | The value of this variable is used as an index to read an error massege from wtWebioEA2x2ERP-24VDiagErrorMessage. Errors are numbered from 1 to wtWebioEA2x2ERP… |
| 1.3.6.1.4.1.5040.1.2.31.4.4 | ScalarwtWebioEA2x2ERP-24VDiagErrorMessage | read-only | mandatory | Using wtWebioEA2x2ERP-24VDiagErrorIndex as an index, the appropriate message is available. |
| 1.3.6.1.4.1.5040.1.2.31.4.5 | ScalarwtWebioEA2x2ERP-24VDiagErrorClear | write-only | mandatory | Writing 1 into this variable clears all diagnosis messages. |
| 1.3.6.1.4.1.5040.1.2.31.41 | NodewtWebioEA2x2ERP-24VAlert1 | This SNMP trap is generated when Alarm 1 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.31.42 | NodewtWebioEA2x2ERP-24VAlert2 | This SNMP trap is generated when Alarm 2 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.31.43 | NodewtWebioEA2x2ERP-24VAlert3 | This SNMP trap is generated when Alarm 3 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.31.44 | NodewtWebioEA2x2ERP-24VAlert4 | This SNMP trap is generated when Alarm 4 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.31.45 | NodewtWebioEA2x2ERP-24VAlert5 | This SNMP trap is generated when Alarm 5 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.31.46 | NodewtWebioEA2x2ERP-24VAlert6 | This SNMP trap is generated when Alarm 6 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.31.47 | NodewtWebioEA2x2ERP-24VAlert7 | This SNMP trap is generated when Alarm 7 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.31.48 | NodewtWebioEA2x2ERP-24VAlert8 | This SNMP trap is generated when Alarm 8 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.31.49 | NodewtWebioEA2x2ERP-24VAlert9 | This SNMP trap is generated when Alarm 9 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.31.50 | NodewtWebioEA2x2ERP-24VAlert10 | This SNMP trap is generated when Alarm 10 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.31.51 | NodewtWebioEA2x2ERP-24VAlert11 | This SNMP trap is generated when Alarm 11 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.31.52 | NodewtWebioEA2x2ERP-24VAlert12 | This SNMP trap is generated when Alarm 12 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.31.71 | NodewtWebioEA2x2ERP-24VAlert13 | This SNMP trap is generated when Alarm 1 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.31.72 | NodewtWebioEA2x2ERP-24VAlert14 | This SNMP trap is generated when Alarm 2 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.31.73 | NodewtWebioEA2x2ERP-24VAlert15 | This SNMP trap is generated when Alarm 3 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.31.74 | NodewtWebioEA2x2ERP-24VAlert16 | This SNMP trap is generated when Alarm 4 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.31.75 | NodewtWebioEA2x2ERP-24VAlert17 | This SNMP trap is generated when Alarm 5 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.31.76 | NodewtWebioEA2x2ERP-24VAlert18 | This SNMP trap is generated when Alarm 6 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.31.77 | NodewtWebioEA2x2ERP-24VAlert19 | This SNMP trap is generated when Alarm 7 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.31.78 | NodewtWebioEA2x2ERP-24VAlert20 | This SNMP trap is generated when Alarm 8 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.31.79 | NodewtWebioEA2x2ERP-24VAlert21 | This SNMP trap is generated when Alarm 9 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.31.80 | NodewtWebioEA2x2ERP-24VAlert22 | This SNMP trap is generated when Alarm 10 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.31.81 | NodewtWebioEA2x2ERP-24VAlert23 | This SNMP trap is generated when Alarm 11 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.31.82 | NodewtWebioEA2x2ERP-24VAlert24 | This SNMP trap is generated when Alarm 12 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.31.110 | NodewtWebioEA2x2ERP-24VAlertDiag | This SNMP trap is generated when a diagnosis/error message was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.32 | NodewtIpWatcher-24V | |||
| 1.3.6.1.4.1.5040.1.2.32.1 | NodewtIpWatcher-24VInOut | |||
| 1.3.6.1.4.1.5040.1.2.32.1.1 | ScalarwtIpWatcher-24VInputs | read-only | mandatory | Number of idependent inputs. |
| 1.3.6.1.4.1.5040.1.2.32.1.2 | ScalarwtIpWatcher-24VOutputs | read-only | mandatory | Number of idependent outputs. |
| 1.3.6.1.4.1.5040.1.2.32.1.3 | TablewtIpWatcher-24VInputTable | not-accessible | mandatory | List of input indices. |
| 1.3.6.1.4.1.5040.1.2.32.1.3.1 | RowwtIpWatcher-24VInputEntry | not-accessible | mandatory | Number of the inputs. |
| 1.3.6.1.4.1.5040.1.2.32.1.3.1.1 | ColumnwtIpWatcher-24VInputNo | read-only | mandatory | Index numbers of the inputs. |
| 1.3.6.1.4.1.5040.1.2.32.1.3.1.2 | ColumnwtIpWatcher-24VInputCounter | read-only | mandatory | Value of the input counter. |
| 1.3.6.1.4.1.5040.1.2.32.1.3.1.3 | ColumnwtIpWatcher-24VInputCounterClear | read-only | mandatory | Clears the input counter after returning its value. |
| 1.3.6.1.4.1.5040.1.2.32.1.3.1.4 | ColumnwtIpWatcher-24VInputState | read-only | mandatory | Value of a single input bit, 0-OFF, 1-ON. |
| 1.3.6.1.4.1.5040.1.2.32.1.4 | ScalarwtIpWatcher-24VInputValue | read-only | mandatory | This variable is used to read the inputs of the digital I/O port. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corres… |
| 1.3.6.1.4.1.5040.1.2.32.1.5 | TablewtIpWatcher-24VOutputTable | not-accessible | mandatory | List of output indices. |
| 1.3.6.1.4.1.5040.1.2.32.1.5.1 | RowwtIpWatcher-24VOutputEntry | not-accessible | mandatory | Number of the outputs. |
| 1.3.6.1.4.1.5040.1.2.32.1.5.1.1 | ColumnwtIpWatcher-24VOutputNo | read-only | mandatory | Output number. |
| 1.3.6.1.4.1.5040.1.2.32.1.5.1.2 | ColumnwtIpWatcher-24VOutputState | read-write | mandatory | Value of a single output bit, 0-OFF, 1-ON. |
| 1.3.6.1.4.1.5040.1.2.32.1.6 | ScalarwtIpWatcher-24VOutputValue | read-write | mandatory | This variable is used to read and write the outputs of the digital I/O port. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. B… |
| 1.3.6.1.4.1.5040.1.2.32.1.7 | ScalarwtIpWatcher-24VSetOutput | read-write | mandatory | This variable allows setting of individual digital outputs. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds … |
| 1.3.6.1.4.1.5040.1.2.32.1.8 | TablewtIpWatcher-24VAlarmOutputTable | not-accessible | mandatory | List of alarm indices.. |
| 1.3.6.1.4.1.5040.1.2.32.1.8.1 | RowwtIpWatcher-24VAlarmOutputEntry | not-accessible | mandatory | Index reference. |
| 1.3.6.1.4.1.5040.1.2.32.1.8.1.1 | ColumnwtIpWatcher-24VAlarmOutputState | read-write | mandatory | State of the alarm, 0-OFF, 1-ON. |
| 1.3.6.1.4.1.5040.1.2.32.1.8.1.2 | ColumnwtIpWatcher-24VAlarmTriggerState | read-only | mandatory | State of the trigger condition, 0-OFF, 1-ON. |
| 1.3.6.1.4.1.5040.1.2.32.2 | NodewtIpWatcher-24VSessCntrl | |||
| 1.3.6.1.4.1.5040.1.2.32.2.1 | ScalarwtIpWatcher-24VSessCntrlPassword | read-write | mandatory | Entering this password opens a session which is ended by writing a 1 to wtIpWatcher-24VSessCntrlLogout. When read this variable provides a string of length zer… |
| 1.3.6.1.4.1.5040.1.2.32.2.2 | ScalarwtIpWatcher-24VSessCntrlConfigMode | read-only | mandatory | When the device is in SNMP configuration mode, the value 1 is returned, otherwise 0. If the read value is 0 even though the password was written, the device is… |
| 1.3.6.1.4.1.5040.1.2.32.2.3 | ScalarwtIpWatcher-24VSessCntrlLogout | read-write | mandatory | If the device is in configuration mode and the session was opened by this SNMP Manager, writing a 1 to this variable will end the session and all parameters ar… |
| 1.3.6.1.4.1.5040.1.2.32.2.4 | ScalarwtIpWatcher-24VSessCntrlAdminPassword | read-write | mandatory | This password protects access to the variables with administrator rights. It can only be changed by the administrator. If no password was assigned, the valid p… |
| 1.3.6.1.4.1.5040.1.2.32.2.5 | ScalarwtIpWatcher-24VSessCntrlConfigPassword | read-write | mandatory | This password protects access to the variables with configurator rights. It can be changed by the administrator and by the configurator. If no password was ass… |
| 1.3.6.1.4.1.5040.1.2.32.3 | NodewtIpWatcher-24VConfig | |||
| 1.3.6.1.4.1.5040.1.2.32.3.1 | NodewtIpWatcher-24VDevice | |||
| 1.3.6.1.4.1.5040.1.2.32.3.1.1 | NodewtIpWatcher-24VText | |||
| 1.3.6.1.4.1.5040.1.2.32.3.1.1.1 | ScalarwtIpWatcher-24VDeviceName | read-write | mandatory | Name of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.1.2 | ScalarwtIpWatcher-24VDeviceText | read-write | mandatory | Description of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.1.3 | ScalarwtIpWatcher-24VDeviceLocation | read-write | mandatory | Description of the location of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.1.4 | ScalarwtIpWatcher-24VDeviceContact | read-write | mandatory | Contact address of the system operator of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.2 | NodewtIpWatcher-24VTimeDate | |||
| 1.3.6.1.4.1.5040.1.2.32.3.1.2.1 | NodewtIpWatcher-24VTimeZone | |||
| 1.3.6.1.4.1.5040.1.2.32.3.1.2.1.1 | ScalarwtIpWatcher-24VTzOffsetHrs | read-write | mandatory | Offset hours for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.2.1.2 | ScalarwtIpWatcher-24VTzOffsetMin | read-write | mandatory | Offset minutes for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.2.1.3 | ScalarwtIpWatcher-24VTzEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Timezone |
| 1.3.6.1.4.1.5040.1.2.32.3.1.2.1.4 | ScalarwtIpWatcher-24VStTzOffsetHrs | read-write | mandatory | Offset hours of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.2.1.5 | ScalarwtIpWatcher-24VStTzOffsetMin | read-write | mandatory | Offset minutes of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.2.1.6 | ScalarwtIpWatcher-24VStTzEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Summertime |
| 1.3.6.1.4.1.5040.1.2.32.3.1.2.1.7 | ScalarwtIpWatcher-24VStTzStartMonth | read-write | mandatory | Month in which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.2.1.8 | ScalarwtIpWatcher-24VStTzStartMode | read-write | mandatory | Mode of the day of the week for which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.2.1.9 | ScalarwtIpWatcher-24VStTzStartWday | read-write | mandatory | Day of the week on which the change is made from winter time to summer time |
| 1.3.6.1.4.1.5040.1.2.32.3.1.2.1.10 | ScalarwtIpWatcher-24VStTzStartHrs | read-write | mandatory | Hour in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.2.1.11 | ScalarwtIpWatcher-24VStTzStartMin | read-write | mandatory | Minute in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.2.1.12 | ScalarwtIpWatcher-24VStTzStopMonth | read-write | mandatory | Month in which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.2.1.13 | ScalarwtIpWatcher-24VStTzStopMode | read-write | mandatory | Mode of the week day on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.2.1.14 | ScalarwtIpWatcher-24VStTzStopWday | read-write | mandatory | Day of the week on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.2.1.15 | ScalarwtIpWatcher-24VStTzStopHrs | read-write | mandatory | Hour at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.2.1.16 | ScalarwtIpWatcher-24VStTzStopMin | read-write | mandatory | Minute at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.2.2 | NodewtIpWatcher-24VTimeServer | |||
| 1.3.6.1.4.1.5040.1.2.32.3.1.2.2.1 | ScalarwtIpWatcher-24VTimeServer1 | read-write | mandatory | IP address or name of the 1st time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.32.3.1.2.2.2 | ScalarwtIpWatcher-24VTimeServer2 | read-write | mandatory | IP address or name of the 2nd time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.32.3.1.2.2.3 | ScalarwtIpWatcher-24VTsEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Time Server |
| 1.3.6.1.4.1.5040.1.2.32.3.1.2.2.4 | ScalarwtIpWatcher-24VTsSyncTime | read-write | mandatory | Daily synchronisation time with the time server (hour: 0-23). |
| 1.3.6.1.4.1.5040.1.2.32.3.1.2.3 | NodewtIpWatcher-24VDeviceClock | |||
| 1.3.6.1.4.1.5040.1.2.32.3.1.2.3.1 | ScalarwtIpWatcher-24VClockHrs | read-write | mandatory | Clock hours taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.2.3.2 | ScalarwtIpWatcher-24VClockMin | read-write | mandatory | Clock minutes taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.2.3.3 | ScalarwtIpWatcher-24VClockDay | read-write | mandatory | Date: Day of the month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.2.3.4 | ScalarwtIpWatcher-24VClockMonth | read-write | mandatory | Date: Month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.2.3.5 | ScalarwtIpWatcher-24VClockYear | read-write | mandatory | Date: Year, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.3 | NodewtIpWatcher-24VBasic | |||
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.1 | NodewtIpWatcher-24VNetwork | |||
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.1.1 | ScalarwtIpWatcher-24VIpAddress | read-write | mandatory | IP address of the Webio |
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.1.2 | ScalarwtIpWatcher-24VSubnetMask | read-write | mandatory | Subnet mask of the Webio |
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.1.3 | ScalarwtIpWatcher-24VGateway | read-write | mandatory | Gateway of the Webio |
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.1.4 | ScalarwtIpWatcher-24VDnsServer1 | read-write | mandatory | IP address of the 1st DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.1.5 | ScalarwtIpWatcher-24VDnsServer2 | read-write | mandatory | IP address of the 2nd DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.1.6 | ScalarwtIpWatcher-24VAddConfig | read-write | mandatory | Additional configuration (1=ON): Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1: DHCP enable Bit 0: BOOTP enable |
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.2 | NodewtIpWatcher-24VHTTP | |||
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.2.4 | ScalarwtIpWatcher-24VHttpPort | read-write | mandatory | Definition of the standard HTML port (Default: 80). |
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.3 | NodewtIpWatcher-24VMail | |||
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.3.1 | ScalarwtIpWatcher-24VMailAdName | read-write | mandatory | Device name for mail administration. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.3.2 | ScalarwtIpWatcher-24VMailReply | read-write | mandatory | Reply address for the mail server. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.3.3 | ScalarwtIpWatcher-24VMailServer | read-write | mandatory | Name or IP address of the mail server. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.3.4 | ScalarwtIpWatcher-24VMailEnable | read-write | mandatory | Set this bit to enable the sending of mails: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Mail enable |
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.3.5 | ScalarwtIpWatcher-24VMailAuthentication | read-write | mandatory | Selection of the authentication modi: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTE… |
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.3.6 | ScalarwtIpWatcher-24VMailAuthUser | read-write | mandatory | Name of the user to be authenticated. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.3.7 | ScalarwtIpWatcher-24VMailAuthPassword | read-write | mandatory | Authentication password. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.3.8 | ScalarwtIpWatcher-24VMailPop3Server | read-write | mandatory | Name or Ip-address of the POP3 Servers. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.4 | NodewtIpWatcher-24VSNMP | |||
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.4.1 | ScalarwtIpWatcher-24VSnmpEnable | read-write | mandatory | Set bit 0 to enable SNMP. If disabled, the device did not respond to any SNMP requests. Bit 1 decided wether the community string of read operations is compare… |
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.4.2 | ScalarwtIpWatcher-24VSnmpCommunityStringRead | read-write | mandatory | Community string read only |
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.4.3 | ScalarwtIpWatcher-24VSnmpCommunityStringReadWrite | read-write | mandatory | Community string read / write |
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.4.4 | ScalarwtIpWatcher-24VSnmpSystemTrapManagerIP | read-write | mandatory | Name or IP address of the TCP server which accepts the system trap. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.4.5 | ScalarwtIpWatcher-24VSnmpSystemTrapEnable | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2: Diag messages Bit 3-7: unused |
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.5 | NodewtIpWatcher-24VUDP | |||
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.5.1 | ScalarwtIpWatcher-24VUdpAdminPort | read-write | mandatory | Udp port to which the Udp queries ( short form GET requests) can be sent. This port number must be unique within the device. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.5.2 | ScalarwtIpWatcher-24VUdpEnable | read-write | mandatory | Set this bit to enable UDP support: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : UDP enable |
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.5.3 | ScalarwtIpWatcher-24VUdpRemotePort | read-write | mandatory | Udp remote port setting. If this value is set to zero, the source port read from a request will be used as destination port for the answer. A non zero value fo… |
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.7 | NodewtIpWatcher-24VSyslog | |||
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.7.1 | ScalarwtIpWatcher-24VSyslogServerIP | read-write | mandatory | Name or IP address of the Syslog server, which accepts the Syslog messgaes. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.7.2 | ScalarwtIpWatcher-24VSyslogServerPort | read-write | mandatory | Portnumber of the Syslog servers, default 514. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.7.3 | ScalarwtIpWatcher-24VSyslogSystemMessagesEnable | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2: Diag Messages Bit 3-7: unused |
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.7.4 | ScalarwtIpWatcher-24VSyslogEnable | read-write | mandatory | Set bit 0to enable Syslog: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Syslog enable |
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.8 | NodewtIpWatcher-24VFTP | |||
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.8.1 | ScalarwtIpWatcher-24VFTPServerIP | read-write | mandatory | Name or IP address of the FTP server, which accepts the FTP messages. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.8.2 | ScalarwtIpWatcher-24VFTPServerControlPort | read-write | mandatory | Portnumber of the control port of the FTP server, default 21. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.8.3 | ScalarwtIpWatcher-24VFTPUserName | read-write | mandatory | FTP Loggin: user name. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.8.4 | ScalarwtIpWatcher-24VFTPPassword | read-write | mandatory | FTP Loggin: user password. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.8.5 | ScalarwtIpWatcher-24VFTPAccount | read-write | mandatory | FTP Loggin: name of account. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.8.6 | ScalarwtIpWatcher-24VFTPOption | read-write | mandatory | Bit 0 switches the FTP Server in Passiv-Mode, the Client controls the data connection on its own: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit … |
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.8.7 | ScalarwtIpWatcher-24VFTPEnable | read-write | mandatory | Set Bit 0 to enable FTP: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : FTP enable |
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.11 | NodewtIpWatcher-24VIpList | |||
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.11.1 | ScalarwtIpWatcher-24VIpListCount | read-only | mandatory | Number of Ip addresses. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.11.2 | TablewtIpWatcher-24VIpListIfTable | not-accessible | mandatory | Table of inices. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.11.2.1 | RowwtIpWatcher-24VIpListIfEntry | not-accessible | mandatory | Table entry. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.11.2.1.1 | ColumnwtIpWatcher-24VIpListNo | read-only | mandatory | List number of this entry. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.11.3 | TablewtIpWatcher-24VIpListTable | not-accessible | mandatory | List of ip addresses. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.11.3.1 | RowwtIpWatcher-24VIpListEntry | not-accessible | mandatory | List entry. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.11.3.1.1 | ColumnwtIpWatcher-24VIpListName | read-write | mandatory | Name or IP address. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.11.3.1.2 | ColumnwtIpWatcher-24VIpListPort | read-write | mandatory | Port number, zero in the case of broadcast or Ping. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.11.3.1.3 | ColumnwtIpWatcher-24VIpListService | read-write | mandatory | Binary coded scan mode, only one mode can be selected at a particular time: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Ping enable Bit 1-7… |
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.11.3.1.4 | ColumnwtIpWatcher-24VIpListEnable | read-write | mandatory | Binary coded alarm enable: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: enabled in Alarm 1 Bit 1: enabled in Alarm 2 Bit 2: enabled in Alarm… |
| 1.3.6.1.4.1.5040.1.2.32.3.1.3.11.3.1.5 | ColumnwtIpWatcher-24VIpListAlias | read-write | mandatory | Alias Name |
| 1.3.6.1.4.1.5040.1.2.32.3.1.4 | NodewtIpWatcher-24VOutputMode | |||
| 1.3.6.1.4.1.5040.1.2.32.3.1.4.4 | ScalarwtIpWatcher-24VPowerSupplyEnable | read-write | mandatory | Setting this enable bit turns on the intarnal 24V power supply of the outputs. All currents out must not exceed 150mA. At overcurrent condition the power suppl… |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5 | NodewtIpWatcher-24VAlarm | |||
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.1 | ScalarwtIpWatcher-24VAlarmCount | read-only | mandatory | Number of independent alarms. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.2 | TablewtIpWatcher-24VAlarmIfTable | not-accessible | mandatory | List of alarm indices. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.2.1 | RowwtIpWatcher-24VAlarmIfEntry | not-accessible | mandatory | Numbers of the alarms. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.2.1.1 | ColumnwtIpWatcher-24VAlarmNo | read-only | mandatory | Numbers of the alarms. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3 | TablewtIpWatcher-24VAlarmTable | not-accessible | mandatory | List of settings depending on the alarm number. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1 | RowwtIpWatcher-24VAlarmEntry | not-accessible | mandatory | Alarm parameters of the individual alarms. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.5 | ColumnwtIpWatcher-24VAlarmInterval | read-write | mandatory | Send interval for alarm messages. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.6 | ColumnwtIpWatcher-24VAlarmEnable | read-write | mandatory | Binary coded alarm enable: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Mail Enable Bit 1: SNMP Trap enable Bit 2: UDP enable Bit 3: Send in… |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.7 | ColumnwtIpWatcher-24VAlarmMailAddr | read-write | mandatory | E-Mail address for sending the alarm mail to. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.8 | ColumnwtIpWatcher-24VAlarmMailSubject | read-write | mandatory | Subject line for alarm mail. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.9 | ColumnwtIpWatcher-24VAlarmMailText | read-write | mandatory | Alarm mail text: States of the Webio device can be included by using special tags. Please refer to the respective Webio manual |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.10 | ColumnwtIpWatcher-24VAlarmSnmpManagerIP | read-write | mandatory | IP address of the SNMP Manager to which the Webio device should send SNMP traps. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.11 | ColumnwtIpWatcher-24VAlarmSnmpTrapText | read-write | mandatory | This text appears in the trap body. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.12 | ColumnwtIpWatcher-24VAlarmUdpIpAddr | read-write | mandatory | IP address of the UDP listener to which the Webio device should send UDP traps. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.13 | ColumnwtIpWatcher-24VAlarmUdpPort | read-write | mandatory | Port number of the UDP listener to which the Webio device should send UDP traps. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.14 | ColumnwtIpWatcher-24VAlarmUdpText | read-write | mandatory | This text appears in the UDP trap body. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.15 | ColumnwtIpWatcher-24VAlarmTcpIpAddr | read-write | mandatory | IP address of the TCP listener to which the Webio device should send TCP traps. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.16 | ColumnwtIpWatcher-24VAlarmTcpPort | read-write | mandatory | Port number of the TCP listener to which the Webio device should send TCP traps. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.17 | ColumnwtIpWatcher-24VAlarmTcpText | read-write | mandatory | This text appears in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.18 | ColumnwtIpWatcher-24VAlarmSyslogIpAddr | read-write | mandatory | IP address of the syslog server to which the Webio device should send syslog messages. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.19 | ColumnwtIpWatcher-24VAlarmSyslogPort | read-write | mandatory | Port number of the syslog server to which the Webio device should send syslog messages. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.20 | ColumnwtIpWatcher-24VAlarmSyslogText | read-write | mandatory | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.21 | ColumnwtIpWatcher-24VAlarmFtpDataPort | read-write | mandatory | Local data port: 1..65535 or AUTO: the next free port will be assigned. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.22 | ColumnwtIpWatcher-24VAlarmFtpFileName | read-write | mandatory | Name of the file including path informations. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.23 | ColumnwtIpWatcher-24VAlarmFtpText | read-write | mandatory | Message text to store on the FTP server. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.24 | ColumnwtIpWatcher-24VAlarmFtpOption | read-write | mandatory | Binary coded options, select only one option at the same time: STORE = replace file APPEND = append message at the end of the file Octet 1: unused Octet 2: unu… |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.25 | ColumnwtIpWatcher-24VAlarmTimerCron | read-write | mandatory | This entry contains 5 space or tab seperated text fields for time trigger definition. Each field must match with the actual time to trigger a message, weekday … |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.26 | ColumnwtIpWatcher-24VAlarmMailReleaseSubject | read-write | mandatory | Subject line for alarm mail. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.27 | ColumnwtIpWatcher-24VAlarmMailReleaseText | read-write | mandatory | Release Alarm mail text: States of the Webio device can be included by using special tags. Please refer to the respective Webio manual |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.28 | ColumnwtIpWatcher-24VAlarmSnmpTrapReleaseText | read-write | mandatory | This text appears in the trap body. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.29 | ColumnwtIpWatcher-24VAlarmUdpReleaseText | read-write | mandatory | This text appears in the UDP trap body. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.30 | ColumnwtIpWatcher-24VAlarmTcpReleaseText | read-write | mandatory | This text appears in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.31 | ColumnwtIpWatcher-24VAlarmSyslogReleaseText | read-write | mandatory | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.32 | ColumnwtIpWatcher-24VAlarmFtpReleaseText | read-write | mandatory | Message text to store on the FTP server. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.33 | ColumnwtIpWatcher-24VAlarmName | read-write | mandatory | Name of the alarm. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.34 | ColumnwtIpWatcher-24VAlarmGlobalEnable | read-write | mandatory | Binary coded alarm activation: Die OCTETS werden bitweise interpretiert. Bit 0 entspricht dem LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bit… |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.35 | ColumnwtIpWatcher-24VAlarmCounterClear | read-write | mandatory | Binary coded options: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bit 2-7: un… |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.36 | ColumnwtIpWatcher-24VAlarmAckEnable | read-write | mandatory | Binary coded options: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bit 2-7: un… |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.37 | ColumnwtIpWatcher-24VAlarmAckPort | read-write | mandatory | Number of the input, which clears the alarm (1-6). |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.38 | ColumnwtIpWatcher-24VAlarmSetPort | read-write | mandatory | Number of the output, which will be set by this alarm (1-6). The configuration of pulse mode and polarity defined in the port output section is used. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.39 | ColumnwtIpWatcher-24VAlarmMailTrgClearSubject | read-write | mandatory | Subject line for alarm mail. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.40 | ColumnwtIpWatcher-24VAlarmMailTrgClearText | read-write | mandatory | Alarm mail text: States of the Webio device can be included by using special tags. Please refer to the respective Webio manual |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.41 | ColumnwtIpWatcher-24VAlarmSnmpTrapTrgClearText | read-write | mandatory | This text appears in the trap body. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.42 | ColumnwtIpWatcher-24VAlarmUdpTrgClearText | read-write | mandatory | This text appears in the UDP trap body. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.43 | ColumnwtIpWatcher-24VAlarmTcpTrgClearText | read-write | mandatory | This text appears in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.44 | ColumnwtIpWatcher-24VAlarmSyslogTrgClearText | read-write | mandatory | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.45 | ColumnwtIpWatcher-24VAlarmFtpTrgClearText | read-write | mandatory | Message text to store on the FTP server. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.46 | ColumnwtIpWatcher-24VAlarmMailTrapTxEnable | read-write | mandatory | Binary coded options: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bit 4-7: un… |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.47 | ColumnwtIpWatcher-24VAlarmSnmpTrapTrapTxEnable | read-write | mandatory | Binary coded options: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bit 4-7: un… |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.48 | ColumnwtIpWatcher-24VAlarmUdpTrapTxEnable | read-write | mandatory | Binary coded options: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bit 4-7: un… |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.49 | ColumnwtIpWatcher-24VAlarmTcpTrapTxEnable | read-write | mandatory | Binary coded options: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bit 4-7: un… |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.50 | ColumnwtIpWatcher-24VAlarmSyslogTrapTxEnable | read-write | mandatory | Binary coded options: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bit 4-7: un… |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.51 | ColumnwtIpWatcher-24VAlarmFtpTrapTxEnable | read-write | mandatory | Binary coded options: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bit 4-7: un… |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.52 | ColumnwtIpWatcher-24VAlarmTriggerCount | read-write | mandatory | Alarm will be send if the trigger condition occours TriggerCount times. |
| 1.3.6.1.4.1.5040.1.2.32.3.1.5.3.1.53 | ColumnwtIpWatcher-24VAlarmPollingRate | read-write | mandatory | Time in seconds. |
| 1.3.6.1.4.1.5040.1.2.32.3.2 | NodewtIpWatcher-24VPorts | |||
| 1.3.6.1.4.1.5040.1.2.32.3.2.1 | TablewtIpWatcher-24VInputPortTable | not-accessible | mandatory | List of settings depending on the input number. |
| 1.3.6.1.4.1.5040.1.2.32.3.2.1.1 | RowwtIpWatcher-24VInputPortEntry | not-accessible | mandatory | Input parameter for the individual inputs. |
| 1.3.6.1.4.1.5040.1.2.32.3.2.1.1.1 | ColumnwtIpWatcher-24VPortInputName | read-write | mandatory | Name of the input. |
| 1.3.6.1.4.1.5040.1.2.32.3.2.1.1.2 | ColumnwtIpWatcher-24VPortInputText | read-write | mandatory | Description of the input. |
| 1.3.6.1.4.1.5040.1.2.32.3.2.1.1.4 | ColumnwtIpWatcher-24VPortInputFilter | read-write | mandatory | Pulses with a duration shorter than here specified (duration in 1/1000 sec), are ignored. |
| 1.3.6.1.4.1.5040.1.2.32.3.2.2 | TablewtIpWatcher-24VOutputPortTable | not-accessible | mandatory | List of settings depending on the output number. |
| 1.3.6.1.4.1.5040.1.2.32.3.2.2.1 | RowwtIpWatcher-24VOutputPortEntry | not-accessible | mandatory | Output parameters of the individual outputs. |
| 1.3.6.1.4.1.5040.1.2.32.3.2.2.1.1 | ColumnwtIpWatcher-24VPortOutputName | read-write | mandatory | Name of the output. |
| 1.3.6.1.4.1.5040.1.2.32.3.2.2.1.2 | ColumnwtIpWatcher-24VPortOutputText | read-write | mandatory | Description of the output. |
| 1.3.6.1.4.1.5040.1.2.32.3.2.2.1.9 | ColumnwtIpWatcher-24VPortPulseDuration | read-write | mandatory | Pulse length in 1/1000 sec. Setting this value to zero, disables the pulse output. |
| 1.3.6.1.4.1.5040.1.2.32.3.2.2.1.10 | ColumnwtIpWatcher-24VPortPulsePolarity | read-write | mandatory | This value defines the polarity of the output pulse, if wtIpWatcher-24VPortPulseDuration is not set to zero. After the pulse is finished, the output switches b… |
| 1.3.6.1.4.1.5040.1.2.32.3.3 | NodewtIpWatcher-24VManufact | |||
| 1.3.6.1.4.1.5040.1.2.32.3.3.1 | ScalarwtIpWatcher-24VMfName | read-write | mandatory | Manufacturer company name |
| 1.3.6.1.4.1.5040.1.2.32.3.3.2 | ScalarwtIpWatcher-24VMfAddr | read-write | mandatory | Manufacturer address. |
| 1.3.6.1.4.1.5040.1.2.32.3.3.3 | ScalarwtIpWatcher-24VMfHotline | read-write | mandatory | Manufacturer hotline. |
| 1.3.6.1.4.1.5040.1.2.32.3.3.4 | ScalarwtIpWatcher-24VMfInternet | read-write | mandatory | Manufacturer Internet address. |
| 1.3.6.1.4.1.5040.1.2.32.3.3.5 | ScalarwtIpWatcher-24VMfDeviceTyp | read-write | mandatory | Manufacturer device name (model number). |
| 1.3.6.1.4.1.5040.1.2.32.4 | NodewtIpWatcher-24VDiag | |||
| 1.3.6.1.4.1.5040.1.2.32.4.1 | ScalarwtIpWatcher-24VDiagErrorCount | read-only | mandatory | Number of entries in the error memory. |
| 1.3.6.1.4.1.5040.1.2.32.4.2 | ScalarwtIpWatcher-24VDiagBinaryError | read-only | mandatory | Error causes coded bit-by-bit. |
| 1.3.6.1.4.1.5040.1.2.32.4.3 | ScalarwtIpWatcher-24VDiagErrorIndex | read-write | mandatory | The value of this variable is used as an index to read an error massege from wtIpWatcher-24VDiagErrorMessage. Errors are numbered from 1 to wtIpWatcher-24VDiag… |
| 1.3.6.1.4.1.5040.1.2.32.4.4 | ScalarwtIpWatcher-24VDiagErrorMessage | read-only | mandatory | Using wtIpWatcher-24VDiagErrorIndex as an index, the appropriate message is available. |
| 1.3.6.1.4.1.5040.1.2.32.4.5 | ScalarwtIpWatcher-24VDiagErrorClear | write-only | mandatory | Writing 1 into this variable clears all diagnosis messages. |
| 1.3.6.1.4.1.5040.1.2.32.41 | NodewtIpWatcher-24VAlert1 | This SNMP trap is generated when Alarm 1 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.32.42 | NodewtIpWatcher-24VAlert2 | This SNMP trap is generated when Alarm 2 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.32.43 | NodewtIpWatcher-24VAlert3 | This SNMP trap is generated when Alarm 3 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.32.44 | NodewtIpWatcher-24VAlert4 | This SNMP trap is generated when Alarm 4 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.32.45 | NodewtIpWatcher-24VAlert5 | This SNMP trap is generated when Alarm 5 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.32.46 | NodewtIpWatcher-24VAlert6 | This SNMP trap is generated when Alarm 6 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.32.47 | NodewtIpWatcher-24VAlert7 | This SNMP trap is generated when Alarm 7 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.32.48 | NodewtIpWatcher-24VAlert8 | This SNMP trap is generated when Alarm 8 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.32.49 | NodewtIpWatcher-24VAlert9 | This SNMP trap is generated when Alarm 9 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.32.50 | NodewtIpWatcher-24VAlert10 | This SNMP trap is generated when Alarm 10 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.32.51 | NodewtIpWatcher-24VAlert11 | This SNMP trap is generated when Alarm 11 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.32.52 | NodewtIpWatcher-24VAlert12 | This SNMP trap is generated when Alarm 12 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.32.71 | NodewtIpWatcher-24VAlert13 | This SNMP trap is generated when Alarm 1 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.32.72 | NodewtIpWatcher-24VAlert14 | This SNMP trap is generated when Alarm 2 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.32.73 | NodewtIpWatcher-24VAlert15 | This SNMP trap is generated when Alarm 3 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.32.74 | NodewtIpWatcher-24VAlert16 | This SNMP trap is generated when Alarm 4 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.32.75 | NodewtIpWatcher-24VAlert17 | This SNMP trap is generated when Alarm 5 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.32.76 | NodewtIpWatcher-24VAlert18 | This SNMP trap is generated when Alarm 6 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.32.77 | NodewtIpWatcher-24VAlert19 | This SNMP trap is generated when Alarm 7 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.32.78 | NodewtIpWatcher-24VAlert20 | This SNMP trap is generated when Alarm 8 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.32.79 | NodewtIpWatcher-24VAlert21 | This SNMP trap is generated when Alarm 9 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.32.80 | NodewtIpWatcher-24VAlert22 | This SNMP trap is generated when Alarm 10 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.32.81 | NodewtIpWatcher-24VAlert23 | This SNMP trap is generated when Alarm 11 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.32.82 | NodewtIpWatcher-24VAlert24 | This SNMP trap is generated when Alarm 12 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.32.91 | NodewtIpWatcher-24VAlert25 | This SNMP trap is generated when the trigger of the Alarm 1 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.32.92 | NodewtIpWatcher-24VAlert26 | This SNMP trap is generated when the trigger of the Alarm 2 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.32.93 | NodewtIpWatcher-24VAlert27 | This SNMP trap is generated when the trigger of the Alarm 3 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.32.94 | NodewtIpWatcher-24VAlert28 | This SNMP trap is generated when the trigger of the Alarm 4 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.32.95 | NodewtIpWatcher-24VAlert29 | This SNMP trap is generated when the trigger of the Alarm 5 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.32.96 | NodewtIpWatcher-24VAlert30 | This SNMP trap is generated when the trigger of the Alarm 6 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.32.97 | NodewtIpWatcher-24VAlert31 | This SNMP trap is generated when the trigger of the Alarm 7 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.32.98 | NodewtIpWatcher-24VAlert32 | This SNMP trap is generated when the trigger of the Alarm 8 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.32.99 | NodewtIpWatcher-24VAlert33 | This SNMP trap is generated when the trigger of the Alarm 9 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.32.100 | NodewtIpWatcher-24VAlert34 | This SNMP trap is generated when the trigger of the Alarm 10 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.32.101 | NodewtIpWatcher-24VAlert35 | This SNMP trap is generated when the trigger of the Alarm 11 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.32.102 | NodewtIpWatcher-24VAlert36 | This SNMP trap is generated when the trigger of the Alarm 12 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.32.110 | NodewtIpWatcher-24VAlertDiag | This SNMP trap is generated when a diagnosis/error message was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.33 | NodewtTrapReceiver2x2 | |||
| 1.3.6.1.4.1.5040.1.2.33.1 | NodewtTrapReceiver2x2InOut | |||
| 1.3.6.1.4.1.5040.1.2.33.1.1 | ScalarwtTrapReceiver2x2Inputs | read-only | mandatory | Number of idependent inputs. |
| 1.3.6.1.4.1.5040.1.2.33.1.2 | ScalarwtTrapReceiver2x2Outputs | read-only | mandatory | Number of idependent outputs. |
| 1.3.6.1.4.1.5040.1.2.33.1.3 | TablewtTrapReceiver2x2InputTable | not-accessible | mandatory | List of input indices. |
| 1.3.6.1.4.1.5040.1.2.33.1.3.1 | RowwtTrapReceiver2x2InputEntry | not-accessible | mandatory | Number of the inputs. |
| 1.3.6.1.4.1.5040.1.2.33.1.3.1.1 | ColumnwtTrapReceiver2x2InputNo | read-only | mandatory | Index numbers of the inputs. |
| 1.3.6.1.4.1.5040.1.2.33.1.3.1.4 | ColumnwtTrapReceiver2x2InputState | read-only | mandatory | Value of a single input bit, 0-OFF, 1-ON. |
| 1.3.6.1.4.1.5040.1.2.33.1.4 | ScalarwtTrapReceiver2x2InputValue | read-only | mandatory | This variable is used to read the inputs of the digital I/O port. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corres… |
| 1.3.6.1.4.1.5040.1.2.33.1.5 | TablewtTrapReceiver2x2OutputTable | not-accessible | mandatory | List of output indices. |
| 1.3.6.1.4.1.5040.1.2.33.1.5.1 | RowwtTrapReceiver2x2OutputEntry | not-accessible | mandatory | Number of the outputs. |
| 1.3.6.1.4.1.5040.1.2.33.1.5.1.1 | ColumnwtTrapReceiver2x2OutputNo | read-only | mandatory | Output number. |
| 1.3.6.1.4.1.5040.1.2.33.1.5.1.2 | ColumnwtTrapReceiver2x2OutputState | read-write | mandatory | Value of a single output bit, 0-OFF, 1-ON. |
| 1.3.6.1.4.1.5040.1.2.33.1.6 | ScalarwtTrapReceiver2x2OutputValue | read-only | mandatory | This variable is used to read the outputs of the digital I/O port. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corre… |
| 1.3.6.1.4.1.5040.1.2.33.1.8 | TablewtTrapReceiver2x2ActionOutputTable | not-accessible | mandatory | List of alarm indices.. |
| 1.3.6.1.4.1.5040.1.2.33.1.8.1 | RowwtTrapReceiver2x2ActionOutputEntry | not-accessible | mandatory | Index reference. |
| 1.3.6.1.4.1.5040.1.2.33.1.8.1.1 | ColumnwtTrapReceiver2x2ActionOutputState | read-write | mandatory | State of the alarm, 0-OFF, 1-ON. |
| 1.3.6.1.4.1.5040.1.2.33.1.8.1.2 | ColumnwtTrapReceiver2x2ActionTriggerState | read-only | mandatory | State of the trigger condition, 0-OFF, 1-ON. |
| 1.3.6.1.4.1.5040.1.2.33.1.9 | TablewtTrapReceiver2x2SystemTimerTable | not-accessible | mandatory | List of system timer. |
| 1.3.6.1.4.1.5040.1.2.33.1.9.1 | RowwtTrapReceiver2x2SystemTimerEntry | not-accessible | mandatory | Number of the system timer. |
| 1.3.6.1.4.1.5040.1.2.33.1.9.1.1 | ColumnwtTrapReceiver2x2SystemTimerNo | read-only | mandatory | Index number of the system timer. |
| 1.3.6.1.4.1.5040.1.2.33.1.10 | TablewtTrapReceiver2x2ButtonTable | not-accessible | mandatory | List of buttons. |
| 1.3.6.1.4.1.5040.1.2.33.1.10.1 | RowwtTrapReceiver2x2ButtonEntry | not-accessible | mandatory | Number of the button. |
| 1.3.6.1.4.1.5040.1.2.33.1.10.1.1 | ColumnwtTrapReceiver2x2ButtonNo | read-only | mandatory | Index numder of the button. |
| 1.3.6.1.4.1.5040.1.2.33.2 | NodewtTrapReceiver2x2SessCntrl | |||
| 1.3.6.1.4.1.5040.1.2.33.2.1 | ScalarwtTrapReceiver2x2SessCntrlPassword | read-write | mandatory | Entering this password opens a session which is ended by writing a 1 to wtTrapReceiver2x2SessCntrlLogout. When read this variable provides a string of length z… |
| 1.3.6.1.4.1.5040.1.2.33.2.2 | ScalarwtTrapReceiver2x2SessCntrlConfigMode | read-only | mandatory | When the device is in SNMP configuration mode, the value 1 is returned, otherwise 0. If the read value is 0 even though the password was written, the device is… |
| 1.3.6.1.4.1.5040.1.2.33.2.3 | ScalarwtTrapReceiver2x2SessCntrlLogout | read-write | mandatory | If the device is in configuration mode and the session was opened by this SNMP Manager, writing a 1 to this variable will end the session and all parameters ar… |
| 1.3.6.1.4.1.5040.1.2.33.2.4 | ScalarwtTrapReceiver2x2SessCntrlAdminPassword | read-write | mandatory | This password protects access to the variables with administrator rights. It can only be changed by the administrator. If no password was assigned, the valid p… |
| 1.3.6.1.4.1.5040.1.2.33.2.5 | ScalarwtTrapReceiver2x2SessCntrlConfigPassword | read-write | mandatory | This password protects access to the variables with configurator rights. It can be changed by the administrator and by the configurator. If no password was ass… |
| 1.3.6.1.4.1.5040.1.2.33.3 | NodewtTrapReceiver2x2Config | |||
| 1.3.6.1.4.1.5040.1.2.33.3.1 | NodewtTrapReceiver2x2Device | |||
| 1.3.6.1.4.1.5040.1.2.33.3.1.1 | NodewtTrapReceiver2x2Text | |||
| 1.3.6.1.4.1.5040.1.2.33.3.1.1.1 | ScalarwtTrapReceiver2x2DeviceName | read-write | mandatory | Name of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.1.2 | ScalarwtTrapReceiver2x2DeviceText | read-write | mandatory | Description of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.1.3 | ScalarwtTrapReceiver2x2DeviceLocation | read-write | mandatory | Description of the location of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.1.4 | ScalarwtTrapReceiver2x2DeviceContact | read-write | mandatory | Contact address of the system operator of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.2 | NodewtTrapReceiver2x2TimeDate | |||
| 1.3.6.1.4.1.5040.1.2.33.3.1.2.1 | NodewtTrapReceiver2x2TimeZone | |||
| 1.3.6.1.4.1.5040.1.2.33.3.1.2.1.1 | ScalarwtTrapReceiver2x2TzOffsetHrs | read-write | mandatory | Offset hours for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.2.1.2 | ScalarwtTrapReceiver2x2TzOffsetMin | read-write | mandatory | Offset minutes for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.2.1.3 | ScalarwtTrapReceiver2x2TzEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Timezone |
| 1.3.6.1.4.1.5040.1.2.33.3.1.2.1.4 | ScalarwtTrapReceiver2x2StTzOffsetHrs | read-write | mandatory | Offset hours of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.2.1.5 | ScalarwtTrapReceiver2x2StTzOffsetMin | read-write | mandatory | Offset minutes of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.2.1.6 | ScalarwtTrapReceiver2x2StTzEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Summertime |
| 1.3.6.1.4.1.5040.1.2.33.3.1.2.1.7 | ScalarwtTrapReceiver2x2StTzStartMonth | read-write | mandatory | Month in which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.2.1.8 | ScalarwtTrapReceiver2x2StTzStartMode | read-write | mandatory | Mode of the day of the week for which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.2.1.9 | ScalarwtTrapReceiver2x2StTzStartWday | read-write | mandatory | Day of the week on which the change is made from winter time to summer time |
| 1.3.6.1.4.1.5040.1.2.33.3.1.2.1.10 | ScalarwtTrapReceiver2x2StTzStartHrs | read-write | mandatory | Hour in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.2.1.11 | ScalarwtTrapReceiver2x2StTzStartMin | read-write | mandatory | Minute in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.2.1.12 | ScalarwtTrapReceiver2x2StTzStopMonth | read-write | mandatory | Month in which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.2.1.13 | ScalarwtTrapReceiver2x2StTzStopMode | read-write | mandatory | Mode of the week day on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.2.1.14 | ScalarwtTrapReceiver2x2StTzStopWday | read-write | mandatory | Day of the week on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.2.1.15 | ScalarwtTrapReceiver2x2StTzStopHrs | read-write | mandatory | Hour at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.2.1.16 | ScalarwtTrapReceiver2x2StTzStopMin | read-write | mandatory | Minute at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.2.2 | NodewtTrapReceiver2x2TimeServer | |||
| 1.3.6.1.4.1.5040.1.2.33.3.1.2.2.1 | ScalarwtTrapReceiver2x2TimeServer1 | read-write | mandatory | IP address or name of the 1st time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.33.3.1.2.2.2 | ScalarwtTrapReceiver2x2TimeServer2 | read-write | mandatory | IP address or name of the 2nd time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.33.3.1.2.2.3 | ScalarwtTrapReceiver2x2TsEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Time Server |
| 1.3.6.1.4.1.5040.1.2.33.3.1.2.2.4 | ScalarwtTrapReceiver2x2TsSyncTime | read-write | mandatory | Daily synchronisation time with the time server (hour: 0-23). |
| 1.3.6.1.4.1.5040.1.2.33.3.1.2.3 | NodewtTrapReceiver2x2DeviceClock | |||
| 1.3.6.1.4.1.5040.1.2.33.3.1.2.3.1 | ScalarwtTrapReceiver2x2ClockHrs | read-write | mandatory | Clock hours taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.2.3.2 | ScalarwtTrapReceiver2x2ClockMin | read-write | mandatory | Clock minutes taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.2.3.3 | ScalarwtTrapReceiver2x2ClockDay | read-write | mandatory | Date: Day of the month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.2.3.4 | ScalarwtTrapReceiver2x2ClockMonth | read-write | mandatory | Date: Month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.2.3.5 | ScalarwtTrapReceiver2x2ClockYear | read-write | mandatory | Date: Year, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.3 | NodewtTrapReceiver2x2Basic | |||
| 1.3.6.1.4.1.5040.1.2.33.3.1.3.1 | NodewtTrapReceiver2x2Network | |||
| 1.3.6.1.4.1.5040.1.2.33.3.1.3.1.1 | ScalarwtTrapReceiver2x2IpAddress | read-write | mandatory | IP address of the Webio |
| 1.3.6.1.4.1.5040.1.2.33.3.1.3.1.2 | ScalarwtTrapReceiver2x2SubnetMask | read-write | mandatory | Subnet mask of the Webio |
| 1.3.6.1.4.1.5040.1.2.33.3.1.3.1.3 | ScalarwtTrapReceiver2x2Gateway | read-write | mandatory | Gateway of the Webio |
| 1.3.6.1.4.1.5040.1.2.33.3.1.3.1.4 | ScalarwtTrapReceiver2x2DnsServer1 | read-write | mandatory | IP address of the 1st DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.33.3.1.3.1.5 | ScalarwtTrapReceiver2x2DnsServer2 | read-write | mandatory | IP address of the 2nd DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.33.3.1.3.1.6 | ScalarwtTrapReceiver2x2AddConfig | read-write | mandatory | Additional configuration (1=ON): Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1: DHCP enable Bit 0: BOOTP enable |
| 1.3.6.1.4.1.5040.1.2.33.3.1.3.2 | NodewtTrapReceiver2x2HTTP | |||
| 1.3.6.1.4.1.5040.1.2.33.3.1.3.2.4 | ScalarwtTrapReceiver2x2HttpPort | read-write | mandatory | Definition of the standard HTML port (Default: 80). |
| 1.3.6.1.4.1.5040.1.2.33.3.1.3.3 | NodewtTrapReceiver2x2Mail | |||
| 1.3.6.1.4.1.5040.1.2.33.3.1.3.3.1 | ScalarwtTrapReceiver2x2MailAdName | read-write | mandatory | Device name for mail administration. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.3.3.2 | ScalarwtTrapReceiver2x2MailReply | read-write | mandatory | Reply address for the mail server. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.3.3.3 | ScalarwtTrapReceiver2x2MailServer | read-write | mandatory | Name or IP address of the mail server. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.3.3.4 | ScalarwtTrapReceiver2x2MailEnable | read-write | mandatory | Set this bit to enable the sending of mails: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Mail enable |
| 1.3.6.1.4.1.5040.1.2.33.3.1.3.3.5 | ScalarwtTrapReceiver2x2MailAuthentication | read-write | mandatory | Selection of the authentication modi: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTE… |
| 1.3.6.1.4.1.5040.1.2.33.3.1.3.3.6 | ScalarwtTrapReceiver2x2MailAuthUser | read-write | mandatory | Name of the user to be authenticated. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.3.3.7 | ScalarwtTrapReceiver2x2MailAuthPassword | read-write | mandatory | Authentication password. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.3.3.8 | ScalarwtTrapReceiver2x2MailPop3Server | read-write | mandatory | Name or Ip-address of the POP3 Servers. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.3.4 | NodewtTrapReceiver2x2SNMP | |||
| 1.3.6.1.4.1.5040.1.2.33.3.1.3.4.1 | ScalarwtTrapReceiver2x2SnmpEnable | read-write | mandatory | Set bit 0 to enable SNMP. If disabled, the device did not respond to any SNMP requests. Bit 1 decided wether the community string of read operations is compare… |
| 1.3.6.1.4.1.5040.1.2.33.3.1.3.4.2 | ScalarwtTrapReceiver2x2SnmpCommunityStringRead | read-write | mandatory | Community string read only |
| 1.3.6.1.4.1.5040.1.2.33.3.1.3.4.3 | ScalarwtTrapReceiver2x2SnmpCommunityStringReadWrite | read-write | mandatory | Community string read / write |
| 1.3.6.1.4.1.5040.1.2.33.3.1.3.4.4 | ScalarwtTrapReceiver2x2SnmpSystemTrapManagerIP | read-write | mandatory | Name or IP address of the TCP server which accepts the system trap. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.3.4.5 | ScalarwtTrapReceiver2x2SnmpSystemTrapEnable | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2: Diag messages Bit 3-7: unused |
| 1.3.6.1.4.1.5040.1.2.33.3.1.3.5 | NodewtTrapReceiver2x2UDP | |||
| 1.3.6.1.4.1.5040.1.2.33.3.1.3.5.1 | ScalarwtTrapReceiver2x2UdpAdminPort | read-write | mandatory | Udp port to which the Udp queries ( short form GET requests) can be sent. This port number must be unique within the device. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.3.5.2 | ScalarwtTrapReceiver2x2UdpEnable | read-write | mandatory | Set this bit to enable UDP support: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : UDP enable |
| 1.3.6.1.4.1.5040.1.2.33.3.1.3.5.3 | ScalarwtTrapReceiver2x2UdpRemotePort | read-write | mandatory | Udp remote port setting. If this value is set to zero, the source port read from a request will be used as destination port for the answer. A non zero value fo… |
| 1.3.6.1.4.1.5040.1.2.33.3.1.3.7 | NodewtTrapReceiver2x2Syslog | |||
| 1.3.6.1.4.1.5040.1.2.33.3.1.3.7.1 | ScalarwtTrapReceiver2x2SyslogServerIP | read-write | mandatory | Name or IP address of the Syslog server, which accepts the Syslog messgaes. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.3.7.2 | ScalarwtTrapReceiver2x2SyslogServerPort | read-write | mandatory | Portnumber of the Syslog servers, default 514. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.3.7.3 | ScalarwtTrapReceiver2x2SyslogSystemMessagesEnable | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2: Diag Messages Bit 3-7: unused |
| 1.3.6.1.4.1.5040.1.2.33.3.1.3.7.4 | ScalarwtTrapReceiver2x2SyslogEnable | read-write | mandatory | Set bit 0to enable Syslog: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Syslog enable |
| 1.3.6.1.4.1.5040.1.2.33.3.1.3.8 | NodewtTrapReceiver2x2FTP | |||
| 1.3.6.1.4.1.5040.1.2.33.3.1.3.8.1 | ScalarwtTrapReceiver2x2FTPServerIP | read-write | mandatory | Name or IP address of the FTP server, which accepts the FTP messages. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.3.8.2 | ScalarwtTrapReceiver2x2FTPServerControlPort | read-write | mandatory | Portnumber of the control port of the FTP server, default 21. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.3.8.3 | ScalarwtTrapReceiver2x2FTPUserName | read-write | mandatory | FTP Loggin: user name. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.3.8.4 | ScalarwtTrapReceiver2x2FTPPassword | read-write | mandatory | FTP Loggin: user password. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.3.8.5 | ScalarwtTrapReceiver2x2FTPAccount | read-write | mandatory | FTP Loggin: name of account. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.3.8.6 | ScalarwtTrapReceiver2x2FTPOption | read-write | mandatory | Bit 0 switches the FTP Server in Passiv-Mode, the Client controls the data connection on its own: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit … |
| 1.3.6.1.4.1.5040.1.2.33.3.1.3.8.7 | ScalarwtTrapReceiver2x2FTPEnable | read-write | mandatory | Set Bit 0 to enable FTP: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : FTP enable |
| 1.3.6.1.4.1.5040.1.2.33.3.1.4 | NodewtTrapReceiver2x2OutputMode | |||
| 1.3.6.1.4.1.5040.1.2.33.3.1.4.4 | ScalarwtTrapReceiver2x2PowerSupplyEnable | read-write | mandatory | Setting this enable bit turns on the intarnal 24V power supply of the outputs. All currents out must not exceed 150mA. At overcurrent condition the power suppl… |
| 1.3.6.1.4.1.5040.1.2.33.3.1.5 | NodewtTrapReceiver2x2Action | |||
| 1.3.6.1.4.1.5040.1.2.33.3.1.5.1 | ScalarwtTrapReceiver2x2ActionCount | read-only | mandatory | Number of independent alarms. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.5.2 | TablewtTrapReceiver2x2ActionIfTable | not-accessible | mandatory | List of alarm indices. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.5.2.1 | RowwtTrapReceiver2x2ActionIfEntry | not-accessible | mandatory | Numbers of the alarms. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.5.2.1.1 | ColumnwtTrapReceiver2x2ActionNo | read-only | mandatory | Numbers of the alarms. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.5.3 | TablewtTrapReceiver2x2ActionTable | not-accessible | mandatory | List of settings depending on the alarm number. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.5.3.1 | RowwtTrapReceiver2x2ActionEntry | not-accessible | mandatory | Action parameters of the individual alarms. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.5.3.1.1 | ColumnwtTrapReceiver2x2ActionInputTrigger | read-write | mandatory | This variable allows setting of individual input trigger conditions. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an input. Bit 0 corr… |
| 1.3.6.1.4.1.5040.1.2.33.3.1.5.3.1.5 | ColumnwtTrapReceiver2x2ActionInterval | read-write | mandatory | Send interval for alarm messages. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.5.3.1.6 | ColumnwtTrapReceiver2x2ActionEnable | read-write | mandatory | Binary coded alarm enable: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Mail Enable Bit 1: SNMP Trap enable Bit 2: UDP enable Bit 3: Send in… |
| 1.3.6.1.4.1.5040.1.2.33.3.1.5.3.1.7 | ColumnwtTrapReceiver2x2ActionMailAddr | read-write | mandatory | E-Mail address for sending the alarm mail to. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.5.3.1.8 | ColumnwtTrapReceiver2x2ActionMailSubject | read-write | mandatory | Subject line for alarm mail. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.5.3.1.9 | ColumnwtTrapReceiver2x2ActionMailText | read-write | mandatory | Action mail text: States of the Webio device can be included by using special tags. Please refer to the respective Webio manual |
| 1.3.6.1.4.1.5040.1.2.33.3.1.5.3.1.10 | ColumnwtTrapReceiver2x2ActionSnmpManagerIP | read-write | mandatory | IP address of the SNMP Manager to which the Webio device should send SNMP traps. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.5.3.1.11 | ColumnwtTrapReceiver2x2ActionSnmpTrapText | read-write | mandatory | This text appears in the trap body. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.5.3.1.12 | ColumnwtTrapReceiver2x2ActionUdpIpAddr | read-write | mandatory | IP address of the UDP listener to which the Webio device should send UDP traps. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.5.3.1.13 | ColumnwtTrapReceiver2x2ActionUdpPort | read-write | mandatory | Port number of the UDP listener to which the Webio device should send UDP traps. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.5.3.1.14 | ColumnwtTrapReceiver2x2ActionUdpText | read-write | mandatory | This text appears in the UDP trap body. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.5.3.1.15 | ColumnwtTrapReceiver2x2ActionTcpIpAddr | read-write | mandatory | IP address of the TCP listener to which the Webio device should send TCP traps. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.5.3.1.16 | ColumnwtTrapReceiver2x2ActionTcpPort | read-write | mandatory | Port number of the TCP listener to which the Webio device should send TCP traps. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.5.3.1.17 | ColumnwtTrapReceiver2x2ActionTcpText | read-write | mandatory | This text appears in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.5.3.1.18 | ColumnwtTrapReceiver2x2ActionSyslogIpAddr | read-write | mandatory | IP address of the syslog server to which the Webio device should send syslog messages. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.5.3.1.19 | ColumnwtTrapReceiver2x2ActionSyslogPort | read-write | mandatory | Port number of the syslog server to which the Webio device should send syslog messages. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.5.3.1.20 | ColumnwtTrapReceiver2x2ActionSyslogText | read-write | mandatory | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.5.3.1.21 | ColumnwtTrapReceiver2x2ActionFtpDataPort | read-write | mandatory | Local data port: 1..65535 or AUTO: the next free port will be assigned. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.5.3.1.22 | ColumnwtTrapReceiver2x2ActionFtpFileName | read-write | mandatory | Name of the file including path informations. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.5.3.1.23 | ColumnwtTrapReceiver2x2ActionFtpText | read-write | mandatory | Message text to store on the FTP server. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.5.3.1.24 | ColumnwtTrapReceiver2x2ActionFtpOption | read-write | mandatory | Binary coded options, select only one option at the same time: STORE = replace file APPEND = append message at the end of the file Octet 1: unused Octet 2: unu… |
| 1.3.6.1.4.1.5040.1.2.33.3.1.5.3.1.25 | ColumnwtTrapReceiver2x2ActionTimerCron | read-write | mandatory | This entry contains 10 space or tab seperated text fields defining a time window for sending time triggered messages. 2 CRON time for start time and stop time … |
| 1.3.6.1.4.1.5040.1.2.33.3.1.5.3.1.33 | ColumnwtTrapReceiver2x2ActionName | read-write | mandatory | Name of the alarm. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.5.3.1.34 | ColumnwtTrapReceiver2x2ActionGlobalEnable | read-write | mandatory | Binary coded alarm activation: The OCTETS are interpreted bit-by-bit, with each bit corresponding to an input. Bit 0 corresponds to the LSB. OCTET 1: unused OC… |
| 1.3.6.1.4.1.5040.1.2.33.3.1.5.3.1.55 | ColumnwtTrapReceiver2x2ActionSystemTimerTrigger | read-write | mandatory | Binary coded system timer activation: The OCTETS are interpreted bit-by-bit, with each bit corresponding to an input. Bit 0 corresponds to the LSB. OCTET 1: un… |
| 1.3.6.1.4.1.5040.1.2.33.3.1.5.3.1.56 | ColumnwtTrapReceiver2x2ActionSystemButtonTrigger | read-write | mandatory | Binary coded button activation: The OCTETS are interpreted bit-by-bit, with each bit corresponding to an input. Bit 0 corresponds to the LSB. OCTET 1: unused O… |
| 1.3.6.1.4.1.5040.1.2.33.3.1.5.3.1.57 | ColumnwtTrapReceiver2x2ActionOutputAction | read-write | mandatory | This variable allows setting of individual output. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an input. Bit 0 corresponds to the LSB… |
| 1.3.6.1.4.1.5040.1.2.33.3.1.6 | NodewtTrapReceiver2x2PrepareInEvents | |||
| 1.3.6.1.4.1.5040.1.2.33.3.1.6.1 | NodewtTrapReceiver2x2WatchList | |||
| 1.3.6.1.4.1.5040.1.2.33.3.1.6.1.1 | ScalarwtTrapReceiver2x2WatchListCount | read-only | mandatory | Number of Ip addresses. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.6.1.2 | TablewtTrapReceiver2x2WatchListIfTable | not-accessible | mandatory | Table of inices. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.6.1.2.1 | RowwtTrapReceiver2x2WatchListIfEntry | not-accessible | mandatory | Table entry. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.6.1.2.1.1 | ColumnwtTrapReceiver2x2WatchListNo | read-only | mandatory | List number of this entry. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.6.1.3 | TablewtTrapReceiver2x2WatchListTable | not-accessible | mandatory | List of ip addresses. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.6.1.3.1 | RowwtTrapReceiver2x2WatchListEntry | not-accessible | mandatory | List entry. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.6.1.3.1.1 | ColumnwtTrapReceiver2x2WatchListName | read-write | mandatory | Name or IP address. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.6.1.3.1.2 | ColumnwtTrapReceiver2x2WatchListPort | read-write | mandatory | Port number, zero in the case of broadcast or Ping. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.6.1.3.1.3 | ColumnwtTrapReceiver2x2WatchListService | read-write | mandatory | Binary coded scan mode, only one mode can be selected at a particular time: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: unused Bit 1: unuse… |
| 1.3.6.1.4.1.5040.1.2.33.3.1.6.1.3.1.4 | ColumnwtTrapReceiver2x2WatchListEnable | read-write | mandatory | Binary coded alarm enable: Octet 1: unused Octet 2: unused Octet 3: Bit 0: enabled in Report 9 Bit 1: enabled in Report 10 Bit 2: enabled in Report 11 Bit 3: e… |
| 1.3.6.1.4.1.5040.1.2.33.3.1.6.1.3.1.5 | ColumnwtTrapReceiver2x2WatchListAlias | read-write | mandatory | Alias Name |
| 1.3.6.1.4.1.5040.1.2.33.3.1.6.1.3.1.6 | ColumnwtTrapReceiver2x2WatchListTrapNo | read-write | mandatory | SNMP Trap No: this filter is only active, if SNMP Trap reveive enable in wtTrapReceiver2x2WatchListService is set. wtTrapReceiver2x2WatchListTrapNo-ColdStart(0… |
| 1.3.6.1.4.1.5040.1.2.33.3.1.6.1.3.1.7 | ColumnwtTrapReceiver2x2WatchListSpecificNo | read-write | mandatory | SNMP Specific No: this filter is only active, if SNMP Trap reveive enable in wtTrapReceiver2x2WatchListService is set. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.6.1.3.1.8 | ColumnwtTrapReceiver2x2WatchListFacility | read-write | mandatory | Syslog message level Facility: this filter is only active, if Syslog receive enable in wtTrapReceiver2x2WatchListService is set. wtTrapReceiver2x2WatchListFaci… |
| 1.3.6.1.4.1.5040.1.2.33.3.1.6.1.3.1.9 | ColumnwtTrapReceiver2x2WatchListSeverity | read-write | mandatory | Syslog message level Severity: this filter is only active, if Syslog receive enable in wtTrapReceiver2x2WatchListService is set. wtTrapReceiver2x2WatchListSeve… |
| 1.3.6.1.4.1.5040.1.2.33.3.1.6.2 | NodewtTrapReceiver2x2InEvSystemTimer | |||
| 1.3.6.1.4.1.5040.1.2.33.3.1.6.2.1 | TablewtTrapReceiver2x2SystemTimerPortTable | not-accessible | mandatory | List of settings depending on the SystemTimer number. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.6.2.1.1 | RowwtTrapReceiver2x2SystemTimerPortEntry | not-accessible | mandatory | SystemTimer parameter for the individual SystemTimer. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.6.2.1.1.1 | ColumnwtTrapReceiver2x2PortSystemTimerEnable | read-write | mandatory | Binary coded SystemTimer enable: The OCTETS are interpreted bit-by-bit, with each bit corresponding to an input. Bit 0 corresponds to the LSB. OCTET 1: ungenut… |
| 1.3.6.1.4.1.5040.1.2.33.3.1.6.2.1.1.2 | ColumnwtTrapReceiver2x2PortSystemTimerName | read-write | mandatory | Name of the SystemTimer. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.6.2.1.1.3 | ColumnwtTrapReceiver2x2PortSystemTimerCron | read-write | mandatory | This entry contains 5 space or tab seperated text fields for time trigger definition. Each field must match with the actual time to trigger a message, weekday … |
| 1.3.6.1.4.1.5040.1.2.33.3.1.6.3 | NodewtTrapReceiver2x2InEvButtons | |||
| 1.3.6.1.4.1.5040.1.2.33.3.1.6.3.1 | TablewtTrapReceiver2x2ButtonPortTable | not-accessible | mandatory | List of settings depending on the button number. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.6.3.1.1 | RowwtTrapReceiver2x2ButtonPortEntry | not-accessible | mandatory | Button parameter for the individual buttons. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.6.3.1.1.1 | ColumnwtTrapReceiver2x2PortButtonEnable | read-write | mandatory | Binary coded button enable: The OCTETS are interpreted bit-by-bit, with each bit corresponding to an input. Bit 0 corresponds to the LSB. OCTET 1: ungenutzt OC… |
| 1.3.6.1.4.1.5040.1.2.33.3.1.6.3.1.1.2 | ColumnwtTrapReceiver2x2PortButtonName | read-write | mandatory | Name of the button. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.6.3.1.1.3 | ColumnwtTrapReceiver2x2PortButtonText | read-write | mandatory | Description of the button. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.6.3.1.1.4 | ColumnwtTrapReceiver2x2PortButtonAccess | read-write | mandatory | Binary coded button access level: The OCTETS are interpreted bit-by-bit, with each bit corresponding to an input. Bit 0 corresponds to the LSB. OCTET 1: unused… |
| 1.3.6.1.4.1.5040.1.2.33.3.1.6.4 | NodewtTrapReceiver2x2InEvInputs | |||
| 1.3.6.1.4.1.5040.1.2.33.3.1.6.4.1 | TablewtTrapReceiver2x2InputPortTable | not-accessible | mandatory | List of settings depending on the input number. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.6.4.1.1 | RowwtTrapReceiver2x2InputPortEntry | not-accessible | mandatory | Input parameter for the individual inputs. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.6.4.1.1.1 | ColumnwtTrapReceiver2x2PortInputName | read-write | mandatory | Name of the input. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.6.4.1.1.2 | ColumnwtTrapReceiver2x2PortInputText | read-write | mandatory | Description of the input. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.6.4.1.1.4 | ColumnwtTrapReceiver2x2PortInputFilter | read-write | mandatory | Pulses with a duration shorter than here specified (duration in 1/1000 sec), are ignored. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.7 | NodewtTrapReceiver2x2PrepareOutEvents | |||
| 1.3.6.1.4.1.5040.1.2.33.3.1.7.1 | NodewtTrapReceiver2x2OutEvOutputs | |||
| 1.3.6.1.4.1.5040.1.2.33.3.1.7.1.1 | TablewtTrapReceiver2x2OutputPortTable | not-accessible | mandatory | List of settings depending on the output number. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.7.1.1.1 | RowwtTrapReceiver2x2OutputPortEntry | not-accessible | mandatory | Output parameters of the individual outputs. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.7.1.1.1.1 | ColumnwtTrapReceiver2x2PortOutputName | read-write | mandatory | Name of the output. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.7.1.1.1.2 | ColumnwtTrapReceiver2x2PortOutputText | read-write | mandatory | Description of the output. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.7.1.1.1.9 | ColumnwtTrapReceiver2x2PortPulseDuration | read-write | mandatory | Pulse length in 1/1000 sec. Setting this value to zero, disables the pulse output. |
| 1.3.6.1.4.1.5040.1.2.33.3.1.7.1.1.1.10 | ColumnwtTrapReceiver2x2PortPulsePolarity | read-write | mandatory | This value defines the polarity of the output pulse, if wtTrapReceiver2x2PortPulseDuration is not set to zero. After the pulse is finished, the output switches… |
| 1.3.6.1.4.1.5040.1.2.33.3.2 | NodewtTrapReceiver2x2Ports | |||
| 1.3.6.1.4.1.5040.1.2.33.3.3 | NodewtTrapReceiver2x2Manufact | |||
| 1.3.6.1.4.1.5040.1.2.33.3.3.1 | ScalarwtTrapReceiver2x2MfName | read-write | mandatory | Manufacturer company name |
| 1.3.6.1.4.1.5040.1.2.33.3.3.2 | ScalarwtTrapReceiver2x2MfAddr | read-write | mandatory | Manufacturer address. |
| 1.3.6.1.4.1.5040.1.2.33.3.3.3 | ScalarwtTrapReceiver2x2MfHotline | read-write | mandatory | Manufacturer hotline. |
| 1.3.6.1.4.1.5040.1.2.33.3.3.4 | ScalarwtTrapReceiver2x2MfInternet | read-write | mandatory | Manufacturer Internet address. |
| 1.3.6.1.4.1.5040.1.2.33.3.3.5 | ScalarwtTrapReceiver2x2MfDeviceTyp | read-write | mandatory | Manufacturer device name (model number). |
| 1.3.6.1.4.1.5040.1.2.33.4 | NodewtTrapReceiver2x2Diag | |||
| 1.3.6.1.4.1.5040.1.2.33.4.1 | ScalarwtTrapReceiver2x2DiagErrorCount | read-only | mandatory | Number of entries in the error memory. |
| 1.3.6.1.4.1.5040.1.2.33.4.2 | ScalarwtTrapReceiver2x2DiagBinaryError | read-only | mandatory | Error causes coded bit-by-bit. |
| 1.3.6.1.4.1.5040.1.2.33.4.3 | ScalarwtTrapReceiver2x2DiagErrorIndex | read-write | mandatory | The value of this variable is used as an index to read an error massege from wtTrapReceiver2x2DiagErrorMessage. Errors are numbered from 1 to wtTrapReceiver2x2… |
| 1.3.6.1.4.1.5040.1.2.33.4.4 | ScalarwtTrapReceiver2x2DiagErrorMessage | read-only | mandatory | Using wtTrapReceiver2x2DiagErrorIndex as an index, the appropriate message is available. |
| 1.3.6.1.4.1.5040.1.2.33.4.5 | ScalarwtTrapReceiver2x2DiagErrorClear | write-only | mandatory | Writing 1 into this variable clears all diagnosis messages. |
| 1.3.6.1.4.1.5040.1.2.33.41 | NodewtTrapReceiver2x2Alert1 | This SNMP trap is generated when Action 1 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.33.42 | NodewtTrapReceiver2x2Alert2 | This SNMP trap is generated when Action 2 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.33.43 | NodewtTrapReceiver2x2Alert3 | This SNMP trap is generated when Action 3 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.33.44 | NodewtTrapReceiver2x2Alert4 | This SNMP trap is generated when Action 4 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.33.45 | NodewtTrapReceiver2x2Alert5 | This SNMP trap is generated when Action 5 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.33.46 | NodewtTrapReceiver2x2Alert6 | This SNMP trap is generated when Action 6 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.33.47 | NodewtTrapReceiver2x2Alert7 | This SNMP trap is generated when Action 7 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.33.48 | NodewtTrapReceiver2x2Alert8 | This SNMP trap is generated when Action 8 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.33.49 | NodewtTrapReceiver2x2Alert9 | This SNMP trap is generated when Action 9 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.33.50 | NodewtTrapReceiver2x2Alert10 | This SNMP trap is generated when Action 10 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.33.51 | NodewtTrapReceiver2x2Alert11 | This SNMP trap is generated when Action 11 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.33.52 | NodewtTrapReceiver2x2Alert12 | This SNMP trap is generated when Action 12 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.33.110 | NodewtTrapReceiver2x2AlertDiag | This SNMP trap is generated when a diagnosis/error message was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.48 | NodewtWebio577xxEA1x1 | |||
| 1.3.6.1.4.1.5040.1.2.48.1 | NodewtWebio577xxEA1x1InOut | |||
| 1.3.6.1.4.1.5040.1.2.48.1.1 | ScalarwtWebio577xxEA1x1Inputs | read-only | mandatory | Number of idependent inputs. |
| 1.3.6.1.4.1.5040.1.2.48.1.2 | ScalarwtWebio577xxEA1x1Outputs | read-only | mandatory | Number of idependent outputs. |
| 1.3.6.1.4.1.5040.1.2.48.1.3 | TablewtWebio577xxEA1x1InputTable | not-accessible | mandatory | List of input indices. |
| 1.3.6.1.4.1.5040.1.2.48.1.3.1 | RowwtWebio577xxEA1x1InputEntry | not-accessible | mandatory | Number of the inputs. |
| 1.3.6.1.4.1.5040.1.2.48.1.3.1.1 | ColumnwtWebio577xxEA1x1InputNo | read-only | mandatory | Index numbers of the inputs. |
| 1.3.6.1.4.1.5040.1.2.48.1.3.1.2 | ColumnwtWebio577xxEA1x1InputCounter | read-only | mandatory | Value of the input counter. |
| 1.3.6.1.4.1.5040.1.2.48.1.3.1.3 | ColumnwtWebio577xxEA1x1InputCounterClear | read-only | mandatory | Clears the input counter after returning its value. |
| 1.3.6.1.4.1.5040.1.2.48.1.3.1.4 | ColumnwtWebio577xxEA1x1InputState | read-only | mandatory | Value of a single input bit, 0-OFF, 1-ON. |
| 1.3.6.1.4.1.5040.1.2.48.1.4 | ScalarwtWebio577xxEA1x1InputValue | read-only | mandatory | This variable is used to read the inputs of the digital I/O port. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corres… |
| 1.3.6.1.4.1.5040.1.2.48.1.5 | TablewtWebio577xxEA1x1OutputTable | not-accessible | mandatory | List of output indices. |
| 1.3.6.1.4.1.5040.1.2.48.1.5.1 | RowwtWebio577xxEA1x1OutputEntry | not-accessible | mandatory | Number of the outputs. |
| 1.3.6.1.4.1.5040.1.2.48.1.5.1.1 | ColumnwtWebio577xxEA1x1OutputNo | read-only | mandatory | Output number. |
| 1.3.6.1.4.1.5040.1.2.48.1.5.1.2 | ColumnwtWebio577xxEA1x1OutputState | read-write | mandatory | Value of a single output bit, 0-OFF, 1-ON. |
| 1.3.6.1.4.1.5040.1.2.48.1.6 | ScalarwtWebio577xxEA1x1OutputValue | read-write | mandatory | This variable is used to read and write the outputs of the digital I/O port. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. B… |
| 1.3.6.1.4.1.5040.1.2.48.1.7 | ScalarwtWebio577xxEA1x1SetOutput | read-write | mandatory | This variable allows setting of individual digital outputs. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds … |
| 1.3.6.1.4.1.5040.1.2.48.2 | NodewtWebio577xxEA1x1SessCntrl | |||
| 1.3.6.1.4.1.5040.1.2.48.2.1 | ScalarwtWebio577xxEA1x1SessCntrlPassword | read-write | mandatory | Entering this password opens a session which is ended by writing a 1 to wtWebio577xxEA1x1SessCntrlLogout. When read this variable provides a string of length z… |
| 1.3.6.1.4.1.5040.1.2.48.2.2 | ScalarwtWebio577xxEA1x1SessCntrlConfigMode | read-only | mandatory | When the device is in SNMP configuration mode, the value 1 is returned, otherwise 0. If the read value is 0 even though the password was written, the device is… |
| 1.3.6.1.4.1.5040.1.2.48.2.3 | ScalarwtWebio577xxEA1x1SessCntrlLogout | read-write | mandatory | If the device is in configuration mode and the session was opened by this SNMP Manager, writing a 1 to this variable will end the session and all parameters ar… |
| 1.3.6.1.4.1.5040.1.2.48.2.4 | ScalarwtWebio577xxEA1x1SessCntrlAdminPassword | read-write | mandatory | This password protects access to the variables with administrator rights. It can only be changed by the administrator. If no password was assigned, the valid p… |
| 1.3.6.1.4.1.5040.1.2.48.2.5 | ScalarwtWebio577xxEA1x1SessCntrlConfigPassword | read-write | mandatory | This password protects access to the variables with configurator rights. It can be changed by the administrator and by the configurator. If no password was ass… |
| 1.3.6.1.4.1.5040.1.2.48.3 | NodewtWebio577xxEA1x1Config | |||
| 1.3.6.1.4.1.5040.1.2.48.3.1 | NodewtWebio577xxEA1x1Device | |||
| 1.3.6.1.4.1.5040.1.2.48.3.1.1 | NodewtWebio577xxEA1x1Text | |||
| 1.3.6.1.4.1.5040.1.2.48.3.1.1.1 | ScalarwtWebio577xxEA1x1DeviceName | read-write | mandatory | Name of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.1.2 | ScalarwtWebio577xxEA1x1DeviceText | read-write | mandatory | Description of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.1.3 | ScalarwtWebio577xxEA1x1DeviceLocation | read-write | mandatory | Description of the location of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.1.4 | ScalarwtWebio577xxEA1x1DeviceContact | read-write | mandatory | Contact address of the system operator of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.2 | NodewtWebio577xxEA1x1TimeDate | |||
| 1.3.6.1.4.1.5040.1.2.48.3.1.2.1 | NodewtWebio577xxEA1x1TimeZone | |||
| 1.3.6.1.4.1.5040.1.2.48.3.1.2.1.1 | ScalarwtWebio577xxEA1x1TzOffsetHrs | read-write | mandatory | Offset hours for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.2.1.2 | ScalarwtWebio577xxEA1x1TzOffsetMin | read-write | mandatory | Offset minutes for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.2.1.3 | ScalarwtWebio577xxEA1x1TzEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Timezone |
| 1.3.6.1.4.1.5040.1.2.48.3.1.2.1.4 | ScalarwtWebio577xxEA1x1StTzOffsetHrs | read-write | mandatory | Offset hours of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.2.1.5 | ScalarwtWebio577xxEA1x1StTzOffsetMin | read-write | mandatory | Offset minutes of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.2.1.6 | ScalarwtWebio577xxEA1x1StTzEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Summertime |
| 1.3.6.1.4.1.5040.1.2.48.3.1.2.1.7 | ScalarwtWebio577xxEA1x1StTzStartMonth | read-write | mandatory | Month in which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.2.1.8 | ScalarwtWebio577xxEA1x1StTzStartMode | read-write | mandatory | Mode of the day of the week for which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.2.1.9 | ScalarwtWebio577xxEA1x1StTzStartWday | read-write | mandatory | Day of the week on which the change is made from winter time to summer time |
| 1.3.6.1.4.1.5040.1.2.48.3.1.2.1.10 | ScalarwtWebio577xxEA1x1StTzStartHrs | read-write | mandatory | Hour in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.2.1.11 | ScalarwtWebio577xxEA1x1StTzStartMin | read-write | mandatory | Minute in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.2.1.12 | ScalarwtWebio577xxEA1x1StTzStopMonth | read-write | mandatory | Month in which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.2.1.13 | ScalarwtWebio577xxEA1x1StTzStopMode | read-write | mandatory | Mode of the week day on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.2.1.14 | ScalarwtWebio577xxEA1x1StTzStopWday | read-write | mandatory | Day of the week on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.2.1.15 | ScalarwtWebio577xxEA1x1StTzStopHrs | read-write | mandatory | Hour at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.2.1.16 | ScalarwtWebio577xxEA1x1StTzStopMin | read-write | mandatory | Minute at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.2.2 | NodewtWebio577xxEA1x1TimeServer | |||
| 1.3.6.1.4.1.5040.1.2.48.3.1.2.2.1 | ScalarwtWebio577xxEA1x1TimeServer1 | read-write | mandatory | IP address or name of the 1st time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.48.3.1.2.2.2 | ScalarwtWebio577xxEA1x1TimeServer2 | read-write | mandatory | IP address or name of the 2nd time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.48.3.1.2.2.3 | ScalarwtWebio577xxEA1x1TsEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Time Server |
| 1.3.6.1.4.1.5040.1.2.48.3.1.2.2.4 | ScalarwtWebio577xxEA1x1TsSyncTime | read-write | mandatory | Daily synchronisation time with the time server (hour: 0-23). |
| 1.3.6.1.4.1.5040.1.2.48.3.1.2.3 | NodewtWebio577xxEA1x1DeviceClock | |||
| 1.3.6.1.4.1.5040.1.2.48.3.1.2.3.1 | ScalarwtWebio577xxEA1x1ClockHrs | read-write | mandatory | Clock hours taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.2.3.2 | ScalarwtWebio577xxEA1x1ClockMin | read-write | mandatory | Clock minutes taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.2.3.3 | ScalarwtWebio577xxEA1x1ClockDay | read-write | mandatory | Date: Day of the month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.2.3.4 | ScalarwtWebio577xxEA1x1ClockMonth | read-write | mandatory | Date: Month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.2.3.5 | ScalarwtWebio577xxEA1x1ClockYear | read-write | mandatory | Date: Year, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3 | NodewtWebio577xxEA1x1Basic | |||
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.1 | NodewtWebio577xxEA1x1Network | |||
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.1.1 | ScalarwtWebio577xxEA1x1IpAddress | read-write | mandatory | IP address of the Webio |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.1.2 | ScalarwtWebio577xxEA1x1SubnetMask | read-write | mandatory | Subnet mask of the Webio |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.1.3 | ScalarwtWebio577xxEA1x1Gateway | read-write | mandatory | Gateway of the Webio |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.1.4 | ScalarwtWebio577xxEA1x1DnsServer1 | read-write | mandatory | IP address of the 1st DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.1.5 | ScalarwtWebio577xxEA1x1DnsServer2 | read-write | mandatory | IP address of the 2nd DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.1.6 | ScalarwtWebio577xxEA1x1AddConfig | read-write | mandatory | Additional configuration (1=ON): Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1: DHCP enable Bit 0: BOOTP enable |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.2 | NodewtWebio577xxEA1x1HTTP | |||
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.2.1 | ScalarwtWebio577xxEA1x1Startup | read-write | mandatory | Binary coded start page, more than one page must not be selected: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 2: user.htm Bit 1: home.htm Bit … |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.2.2 | ScalarwtWebio577xxEA1x1GetHeaderEnable | read-write | mandatory | If bits are set, every answer of a short form GET question will be lead by the IP-address and name of the device (Header) or a HTTP header (HTTP): Octet 1: unu… |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.2.3 | ScalarwtWebio577xxEA1x1HttpInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.2.4 | ScalarwtWebio577xxEA1x1HttpPort | read-write | mandatory | Definition of the standard HTML port (Default: 80). |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.3 | NodewtWebio577xxEA1x1Mail | |||
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.3.1 | ScalarwtWebio577xxEA1x1MailAdName | read-write | mandatory | Device name for mail administration. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.3.2 | ScalarwtWebio577xxEA1x1MailReply | read-write | mandatory | Reply address for the mail server. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.3.3 | ScalarwtWebio577xxEA1x1MailServer | read-write | mandatory | Name or IP address of the mail server. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.3.4 | ScalarwtWebio577xxEA1x1MailEnable | read-write | mandatory | Set this bit to enable the sending of mails: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Mail enable |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.3.5 | ScalarwtWebio577xxEA1x1MailAuthentication | read-write | mandatory | Selection of the authentication modi: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTE… |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.3.6 | ScalarwtWebio577xxEA1x1MailAuthUser | read-write | mandatory | Name of the user to be authenticated. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.3.7 | ScalarwtWebio577xxEA1x1MailAuthPassword | read-write | mandatory | Authentication password. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.3.8 | ScalarwtWebio577xxEA1x1MailPop3Server | read-write | mandatory | Name or Ip-address of the POP3 Servers. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.4 | NodewtWebio577xxEA1x1SNMP | |||
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.4.1 | ScalarwtWebio577xxEA1x1SnmpEnable | read-write | mandatory | Set bit 0 to enable SNMP. If disabled, the device did not respond to any SNMP requests. Bit 1 decided wether the community string of read operations is compare… |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.4.2 | ScalarwtWebio577xxEA1x1SnmpCommunityStringRead | read-write | mandatory | Community string read only |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.4.3 | ScalarwtWebio577xxEA1x1SnmpCommunityStringReadWrite | read-write | mandatory | Community string read / write |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.4.4 | ScalarwtWebio577xxEA1x1SnmpSystemTrapManagerIP | read-write | mandatory | Name or IP address of the TCP server which accepts the system trap. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.4.5 | ScalarwtWebio577xxEA1x1SnmpSystemTrapEnable | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2: Diag messages Bit 3-7: unused |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.4.6 | ScalarwtWebio577xxEA1x1SnmpSystemTrapManagerPort | read-write | mandatory | Port number of the TCP server which accepts the system trap. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.5 | NodewtWebio577xxEA1x1UDP | |||
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.5.1 | ScalarwtWebio577xxEA1x1UdpAdminPort | read-write | mandatory | Udp port to which the Udp queries ( short form GET requests) can be sent. This port number must be unique within the device. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.5.2 | ScalarwtWebio577xxEA1x1UdpEnable | read-write | mandatory | Set this bit to enable UDP support: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : UDP enable |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.5.3 | ScalarwtWebio577xxEA1x1UdpRemotePort | read-write | mandatory | Udp remote port setting. If this value is set to zero, the source port read from a request will be used as destination port for the answer. A non zero value fo… |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.6 | NodewtWebio577xxEA1x1Binary | |||
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.6.1 | ScalarwtWebio577xxEA1x1BinaryModeCount | read-only | mandatory | Number of independent binary channels. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.6.2 | TablewtWebio577xxEA1x1BinaryIfTable | not-accessible | mandatory | Table of indices. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.6.2.1 | RowwtWebio577xxEA1x1BinaryIfEntry | not-accessible | mandatory | Indices of the binary channels. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.6.2.1.1 | ColumnwtWebio577xxEA1x1BinaryModeNo | read-only | mandatory | Number of the binary channel. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.6.3 | TablewtWebio577xxEA1x1BinaryTable | not-accessible | mandatory | Table of properties of the binary mode. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.6.3.1 | RowwtWebio577xxEA1x1BinaryEntry | not-accessible | mandatory | Binary properties. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.6.3.1.1 | ColumnwtWebio577xxEA1x1BinaryOperationMode | read-write | mandatory | Selection of the operation mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: … |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.6.3.1.2 | ColumnwtWebio577xxEA1x1BinaryTcpServerLocalPort | read-write | mandatory | Local TCP port for data exchange in this server mode. This port number must be unique within the device. Reserved port number must not be used (refere to the m… |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.6.3.1.3 | ColumnwtWebio577xxEA1x1BinaryTcpServerInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.6.3.1.4 | ColumnwtWebio577xxEA1x1BinaryTcpServerApplicationMode | read-write | mandatory | Selection of the application mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4… |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.6.3.1.5 | ColumnwtWebio577xxEA1x1BinaryTcpClientLocalPort | read-write | mandatory | Local TCP port for data exchange in this client mode. This port number must be unique within the device. Reserved port number must not be used (refere to the m… |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.6.3.1.6 | ColumnwtWebio577xxEA1x1BinaryTcpClientServerPort | read-write | mandatory | Port number of the server. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when setting t… |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.6.3.1.7 | ColumnwtWebio577xxEA1x1BinaryTcpClientServerIpAddr | read-write | mandatory | Ip address of the server. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when setting th… |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.6.3.1.8 | ColumnwtWebio577xxEA1x1BinaryTcpClientServerPassword | read-write | mandatory | Building a connection may be protected by the administrator password of the server. Enter the server password to establish the connection, if a server administ… |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.6.3.1.9 | ColumnwtWebio577xxEA1x1BinaryTcpClientInactivity | read-write | mandatory | Connection timeout in 100ms. If no data are exchanged within the specified time, the device closes the connection to the server. The value 0 deactivates the ti… |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.6.3.1.10 | ColumnwtWebio577xxEA1x1BinaryTcpClientInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.6.3.1.11 | ColumnwtWebio577xxEA1x1BinaryTcpClientInterval | read-write | mandatory | Configurable interval with a 100ms base, in which the Webio device sends data to the configured application. A interval of zero stopps the periodical sending. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.6.3.1.12 | ColumnwtWebio577xxEA1x1BinaryTcpClientApplicationMode | read-write | mandatory | Selection of the application mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4… |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.6.3.1.13 | ColumnwtWebio577xxEA1x1BinaryUdpPeerLocalPort | read-write | mandatory | Local UDP port for data exchange in this peer to peer mode. This port number must be unique within the device. Reserved port number must not be used (refere to… |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.6.3.1.14 | ColumnwtWebio577xxEA1x1BinaryUdpPeerRemotePort | read-write | mandatory | Port number of the remote device. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when se… |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.6.3.1.15 | ColumnwtWebio577xxEA1x1BinaryUdpPeerRemoteIpAddr | read-write | mandatory | Ip address of the remote device. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when set… |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.6.3.1.16 | ColumnwtWebio577xxEA1x1BinaryUdpPeerInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.6.3.1.17 | ColumnwtWebio577xxEA1x1BinaryUdpPeerInterval | read-write | mandatory | Configurable interval with a 100ms base, in which the Webio device sends data to the configured remote device. A interval of zero stopps the periodical sending. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.6.3.1.18 | ColumnwtWebio577xxEA1x1BinaryUdpPeerApplicationMode | read-write | mandatory | Selection of the application mode: The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds to the LSB. OCTET 1: unus… |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.6.3.1.19 | ColumnwtWebio577xxEA1x1BinaryConnectedPort | read-only | mandatory | Port number of the remote device, after connection has been established. In case of no connection or missing port informations a zero will be read. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.6.3.1.20 | ColumnwtWebio577xxEA1x1BinaryConnectedIpAddr | read-only | mandatory | IP address of the remote device, after connection has been established. In case of no connection or missing port informations 0.0.0.0 will be read. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.6.3.1.21 | ColumnwtWebio577xxEA1x1BinaryTcpServerClientHttpPort | read-write | mandatory | HTTP port number of the remote device at TCP Server Mode. If an mailfunction occurs status informations will be send to this port. Not used at mode Compatible … |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.6.3.1.22 | ColumnwtWebio577xxEA1x1BinaryTcpClientServerHttpPort | read-write | mandatory | HTTP port number of the remote device at TCP Client Mode. In the operating mode Box2Box connection status informations will be exchanged through this port. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.6.3.1.23 | ColumnwtWebio577xxEA1x1BinaryTcpClientServerUserName | read-only | mandatory | User Name to login at the remote server, if authentication needed. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.7 | NodewtWebio577xxEA1x1Syslog | |||
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.7.1 | ScalarwtWebio577xxEA1x1SyslogServerIP | read-write | mandatory | Name or IP address of the Syslog server, which accepts the Syslog messgaes. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.7.2 | ScalarwtWebio577xxEA1x1SyslogServerPort | read-write | mandatory | Portnumber of the Syslog servers, default 514. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.7.3 | ScalarwtWebio577xxEA1x1SyslogSystemMessagesEnable | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2: Diag Messages Bit 3-7: unused |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.7.4 | ScalarwtWebio577xxEA1x1SyslogEnable | read-write | mandatory | Set bit 0to enable Syslog: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Syslog enable |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.8 | NodewtWebio577xxEA1x1FTP | |||
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.8.1 | ScalarwtWebio577xxEA1x1FTPServerIP | read-write | mandatory | Name or IP address of the FTP server, which accepts the FTP messages. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.8.2 | ScalarwtWebio577xxEA1x1FTPServerControlPort | read-write | mandatory | Portnumber of the control port of the FTP server, default 21. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.8.3 | ScalarwtWebio577xxEA1x1FTPUserName | read-write | mandatory | FTP Loggin: user name. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.8.4 | ScalarwtWebio577xxEA1x1FTPPassword | read-write | mandatory | FTP Loggin: user password. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.8.5 | ScalarwtWebio577xxEA1x1FTPAccount | read-write | mandatory | FTP Loggin: name of account. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.8.6 | ScalarwtWebio577xxEA1x1FTPOption | read-write | mandatory | Bit 0 switches the FTP Server in Passiv-Mode, the Client controls the data connection on its own: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit … |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.8.7 | ScalarwtWebio577xxEA1x1FTPEnable | read-write | mandatory | Set Bit 0 to enable FTP: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : FTP enable |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.12 | NodewtWebio577xxEA1x1MQTT | |||
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.12.1 | ScalarwtWebio577xxEA1x1MQTTEnable | read-write | mandatory | Bit 7 schaltet MQTT frei: Octet 1: ungenutzt Octet 2: ungenutzt Octet 3: ungenutzt Octet 4: Bit 0-6: ungenutzt Bit 7 : MQTT enable |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.12.2 | ScalarwtWebio577xxEA1x1MQTTBrockerIP | read-write | mandatory | Name or IP-address of the MQTT-Server. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.12.3 | ScalarwtWebio577xxEA1x1MQTTUserName | read-write | mandatory | MQTT login user name. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.12.4 | ScalarwtWebio577xxEA1x1MQTTPassword | read-write | mandatory | MQTT login password. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.12.5 | ScalarwtWebio577xxEA1x1MQTTLocalPort | read-write | mandatory | Local port number. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.12.6 | ScalarwtWebio577xxEA1x1MQTTBrokerServerPort | read-write | mandatory | MQTT Server port number. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.12.7 | ScalarwtWebio577xxEA1x1MQTTInterval | read-write | mandatory | Ping intervall, if no data has to be send: time in seconds. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.12.8 | ScalarwtWebio577xxEA1x1MQTTLastWillEnable | read-write | mandatory | Bit 0 activate MQTT LastWill message: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : MQTT Last will enable |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.12.9 | ScalarwtWebio577xxEA1x1MQTTLastWillTopic | read-write | mandatory | MQTT Last Will Topic. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.12.10 | ScalarwtWebio577xxEA1x1MQTTLastWillMsg | read-write | mandatory | MQTT Last Will message. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.12.11 | ScalarwtWebio577xxEA1x1MQTTLastWillQoS | read-write | mandatory | Binary coded MQTT Publish QoS: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: QoS 0 Bit 1: QoS 1 Bit 2: QoS 2 Bit 3-7:unused |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.12.12 | ScalarwtWebio577xxEA1x1MQTTLastWillRetain | read-write | mandatory | Binary coded MQTT Publish Retain properties: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0 : retain enable Bit 1-7 : unused |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.12.13 | ScalarwtWebio577xxEA1x1MQTTLastWillConnectEnable | read-write | mandatory | Bit 0 activate MQTT LastWill Connect message: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : MQTT Last will connect message e… |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.12.14 | ScalarwtWebio577xxEA1x1MQTTLastWillConnectMsg | read-write | mandatory | MQTT Last Will Connect message will be send with the QoS and Retain settings of the LastWill message. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.13 | NodewtWebio577xxEA1x1REST | |||
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.13.1 | ScalarwtWebio577xxEA1x1RESTEnable | read-write | mandatory | Bit 0 activates REST: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : REST enable |
| 1.3.6.1.4.1.5040.1.2.48.3.1.3.13.2 | ScalarwtWebio577xxEA1x1RESTDigestAuthEnable | read-write | mandatory | Bit 0 activates Digest-Authentification: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Digest Auth enable |
| 1.3.6.1.4.1.5040.1.2.48.3.1.4 | NodewtWebio577xxEA1x1OutputMode | |||
| 1.3.6.1.4.1.5040.1.2.48.3.1.4.1 | TablewtWebio577xxEA1x1OutputModeTable | not-accessible | mandatory | Table of output mode configurations dependent on the output indices. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.4.1.1 | RowwtWebio577xxEA1x1OutputModeEntry | not-accessible | mandatory | Output mode configurations of the individual outputs. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.4.1.1.1 | ColumnwtWebio577xxEA1x1OutputModeBit | read-write | mandatory | This binary coded output mode defines the individual operation mode for any output. More than one mode must not be selected. The OCTETS are interpreted bit-by-… |
| 1.3.6.1.4.1.5040.1.2.48.3.1.4.2 | ScalarwtWebio577xxEA1x1SafetyTimeout | read-write | mandatory | After this period of time (multiple of 100ms) without receiving data outputs switch to their Safety States. For each output a independend safety state could be… |
| 1.3.6.1.4.1.5040.1.2.48.3.1.4.3 | ScalarwtWebio577xxEA1x1LoadControlEnable | read-write | mandatory | Here the function of automatic load control can be enabled. All output were tested in pairs (0-1). If an error occours at one output, both output of an pair wi… |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5 | NodewtWebio577xxEA1x1Alarm | |||
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.1 | ScalarwtWebio577xxEA1x1AlarmCount | read-only | mandatory | Number of independent alarms. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.2 | TablewtWebio577xxEA1x1AlarmIfTable | not-accessible | mandatory | List of alarm indices. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.2.1 | RowwtWebio577xxEA1x1AlarmIfEntry | not-accessible | mandatory | Numbers of the alarms. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.2.1.1 | ColumnwtWebio577xxEA1x1AlarmNo | read-only | mandatory | Numbers of the alarms. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3 | TablewtWebio577xxEA1x1AlarmTable | not-accessible | mandatory | List of settings depending on the alarm number. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1 | RowwtWebio577xxEA1x1AlarmEntry | not-accessible | mandatory | Alarm parameters of the individual alarms. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.1 | ColumnwtWebio577xxEA1x1AlarmInputTrigger | read-write | mandatory | This variable allows setting of individual input trigger conditions. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an input. Bit 0 corr… |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.2 | ColumnwtWebio577xxEA1x1AlarmOutputTrigger | read-write | mandatory | This variable allows setting of individual output trigger conditions. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 co… |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.3 | ColumnwtWebio577xxEA1x1AlarmSystemTrigger | read-write | mandatory | Binary coded trigger conditions: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, … |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.4 | ColumnwtWebio577xxEA1x1AlarmMaxCounterValue | read-write | mandatory | This variable configures a max. counter value. If an input counter value exceeds this max. value, the corresponding alarm is triggered. Input counters with its… |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.5 | ColumnwtWebio577xxEA1x1AlarmInterval | read-write | mandatory | Send interval for alarm messages. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.6 | ColumnwtWebio577xxEA1x1AlarmEnable | read-write | mandatory | Binary coded alarm enable: Octet 1: unused Octet 2: unused Bit 0: UDP enable Bit1-7: unused Octet 4: Bit 0: Mail Enable Bit 1: SNMP Trap enable Bit 2: TCP Clie… |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.7 | ColumnwtWebio577xxEA1x1AlarmMailAddr | read-write | mandatory | E-Mail address for sending the alarm mail to. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.8 | ColumnwtWebio577xxEA1x1AlarmMailSubject | read-write | mandatory | Subject line for alarm mail. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.9 | ColumnwtWebio577xxEA1x1AlarmMailText | read-write | mandatory | Alarm mail text: States of the Webio device can be included by using special tags. Please refer to the respective Webio manual |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.10 | ColumnwtWebio577xxEA1x1AlarmSnmpManagerIP | read-write | mandatory | IP address of the SNMP Manager to which the Webio device should send SNMP traps. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.11 | ColumnwtWebio577xxEA1x1AlarmSnmpTrapText | read-write | mandatory | This text appears in the trap body. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.12 | ColumnwtWebio577xxEA1x1AlarmUdpIpAddr | read-write | mandatory | IP address of the UDP listener to which the Webio device should send UDP traps. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.13 | ColumnwtWebio577xxEA1x1AlarmUdpPort | read-write | mandatory | Port number of the UDP listener to which the Webio device should send UDP traps. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.14 | ColumnwtWebio577xxEA1x1AlarmUdpText | read-write | mandatory | This text appears in the UDP trap body. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.15 | ColumnwtWebio577xxEA1x1AlarmTcpIpAddr | read-write | mandatory | IP address of the TCP listener to which the Webio device should send TCP traps. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.16 | ColumnwtWebio577xxEA1x1AlarmTcpPort | read-write | mandatory | Port number of the TCP listener to which the Webio device should send TCP traps. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.17 | ColumnwtWebio577xxEA1x1AlarmTcpText | read-write | mandatory | This text appears in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.18 | ColumnwtWebio577xxEA1x1AlarmSyslogIpAddr | read-write | mandatory | IP address of the syslog server to which the Webio device should send syslog messages. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.19 | ColumnwtWebio577xxEA1x1AlarmSyslogPort | read-write | mandatory | Port number of the syslog server to which the Webio device should send syslog messages. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.20 | ColumnwtWebio577xxEA1x1AlarmSyslogText | read-write | mandatory | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.21 | ColumnwtWebio577xxEA1x1AlarmFtpDataPort | read-write | mandatory | Local data port: 1..65535 or AUTO: the next free port will be assigned. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.22 | ColumnwtWebio577xxEA1x1AlarmFtpFileName | read-write | mandatory | Name of the file including path informations. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.23 | ColumnwtWebio577xxEA1x1AlarmFtpText | read-write | mandatory | Message text to store on the FTP server. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.24 | ColumnwtWebio577xxEA1x1AlarmFtpOption | read-write | mandatory | Binary coded options, select only one option at the same time: STORE = replace file APPEND = append message at the end of the file Octet 1: unused Octet 2: unu… |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.25 | ColumnwtWebio577xxEA1x1AlarmTimerCron | read-write | mandatory | This entry contains 5 space or tab seperated text fields for time trigger definition. Each field must match with the actual time to trigger a message, weekday … |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.26 | ColumnwtWebio577xxEA1x1AlarmMailReleaseSubject | read-write | mandatory | Subject line for alarm mail. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.27 | ColumnwtWebio577xxEA1x1AlarmMailReleaseText | read-write | mandatory | Release Alarm mail text: States of the Webio device can be included by using special tags. Please refer to the respective Webio manual |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.28 | ColumnwtWebio577xxEA1x1AlarmSnmpTrapReleaseText | read-write | mandatory | This text appears in the trap body. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.29 | ColumnwtWebio577xxEA1x1AlarmUdpReleaseText | read-write | mandatory | This text appears in the UDP trap body. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.30 | ColumnwtWebio577xxEA1x1AlarmTcpReleaseText | read-write | mandatory | This text appears in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.31 | ColumnwtWebio577xxEA1x1AlarmSyslogReleaseText | read-write | mandatory | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.32 | ColumnwtWebio577xxEA1x1AlarmFtpReleaseText | read-write | mandatory | Message text to store on the FTP server. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.34 | ColumnwtWebio577xxEA1x1AlarmGlobalEnable | read-write | mandatory | Binary coded alarm activation: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bi… |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.58 | ColumnwtWebio577xxEA1x1AlarmCombinationLogic | read-write | mandatory | Binary coded alarm activation:: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, B… |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.59 | ColumnwtWebio577xxEA1x1AlarmTrgMqttTopic | read-write | mandatory | MQTT subscribe topic. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.60 | ColumnwtWebio577xxEA1x1AlarmTrgMqttTopicText | read-write | mandatory | Receiving this text from the MQTT Broker, Alarm will be triggered. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.61 | ColumnwtWebio577xxEA1x1AlarmHttpReqAuthEnable | read-write | mandatory | Binary coded alarm activation: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bi… |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.62 | ColumnwtWebio577xxEA1x1AlarmHttpReqAuthUser | read-write | mandatory | HTTP Request: User |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.63 | ColumnwtWebio577xxEA1x1AlarmHttpReqAuthPassword | read-write | mandatory | HTTP Request: Password |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.64 | ColumnwtWebio577xxEA1x1AlarmHttpReqSetUrl | read-write | mandatory | HTTP Request: Set URL |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.65 | ColumnwtWebio577xxEA1x1AlarmHttpReqClearUrl | read-write | mandatory | HTTP Request: Clear URL |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.66 | ColumnwtWebio577xxEA1x1AlarmHttpReqServerPort | read-write | mandatory | HTTP Request: Server Port |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.67 | ColumnwtWebio577xxEA1x1AlarmMqttTopicPath | read-write | mandatory | MQTT Publish: Topic path |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.68 | ColumnwtWebio577xxEA1x1AlarmMqttTopicSetTopic | read-write | mandatory | MQTT Publish: Topic SET message |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.69 | ColumnwtWebio577xxEA1x1AlarmMqttTopicClear | read-write | mandatory | MQTT Publish: Topic CLEAR message |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.70 | ColumnwtWebio577xxEA1x1AlarmSetOutputsOwn | read-write | mandatory | This variable allows setting of individual output. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds to the LS… |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.71 | ColumnwtWebio577xxEA1x1AlarmSetOutputsServerIp | read-write | mandatory | Set Outputs: Server IP Address |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.72 | ColumnwtWebio577xxEA1x1AlarmSetOutputsServerPort | read-write | mandatory | Set Outputs: Server Port |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.73 | ColumnwtWebio577xxEA1x1AlarmSetOutputsServerPassword | read-write | mandatory | Set Outputs: Server Pasword |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.74 | ColumnwtWebio577xxEA1x1AlarmSetOutputsServerOutputs | read-write | mandatory | This variable allows setting of individual output. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds to the LS… |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.75 | ColumnwtWebio577xxEA1x1AlarmSetOutputsDest | read-write | mandatory | Binary coded value: The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unu… |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.76 | ColumnwtWebio577xxEA1x1AlarmSnmpManagerPort | read-write | mandatory | Port number of the SNMP Manager to which the Webio device should send SNMP traps. |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.77 | ColumnwtWebio577xxEA1x1AlarmMqttQoS | read-write | mandatory | Binary coded value: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: QoS 0 Bit 1: QoS 1 Bit 2: QoS 2 Bit 3-7:unused |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.3.1.78 | ColumnwtWebio577xxEA1x1AlarmMqttRetain | read-write | mandatory | Binary coded value: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0 : retain enable Bit 1-7 : unused |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.4 | ScalarwtWebio577xxEA1x1LoadControlView | read-only | mandatory | Here the result of automatic load control can be read. All output were tested in pairs (0-1). If an error occours at one output, both output of an pair will be… |
| 1.3.6.1.4.1.5040.1.2.48.3.1.5.5 | ScalarwtWebio577xxEA1x1LCShutDownView | read-write | mandatory | Here the result of the automatic load control shut down can be read. All outputs remain switched of, until a zero is written into this variable. But previously… |
| 1.3.6.1.4.1.5040.1.2.48.3.2 | NodewtWebio577xxEA1x1Ports | |||
| 1.3.6.1.4.1.5040.1.2.48.3.2.1 | TablewtWebio577xxEA1x1InputPortTable | not-accessible | mandatory | List of settings depending on the input number. |
| 1.3.6.1.4.1.5040.1.2.48.3.2.1.1 | RowwtWebio577xxEA1x1InputPortEntry | not-accessible | mandatory | Input parameter for the individual inputs. |
| 1.3.6.1.4.1.5040.1.2.48.3.2.1.1.1 | ColumnwtWebio577xxEA1x1PortInputName | read-write | mandatory | Name of the input. |
| 1.3.6.1.4.1.5040.1.2.48.3.2.1.1.2 | ColumnwtWebio577xxEA1x1PortInputText | read-write | mandatory | Description of the input. |
| 1.3.6.1.4.1.5040.1.2.48.3.2.1.1.3 | ColumnwtWebio577xxEA1x1PortInputMode | read-write | mandatory | Binary coded modes: Selecting short pulse detection enable by setting the corresponding bit to 1 enables interrupt support for counting. Only positive edges ar… |
| 1.3.6.1.4.1.5040.1.2.48.3.2.1.1.4 | ColumnwtWebio577xxEA1x1PortInputFilter | read-write | mandatory | Pulses with a duration shorter than here specified (duration in 1/1000 sec), are ignored. |
| 1.3.6.1.4.1.5040.1.2.48.3.2.1.1.5 | ColumnwtWebio577xxEA1x1PortInputBicountPulsePolarity | read-write | mandatory | This value defines the polarity of the input pulse. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 0 : negative polarity Bit 1 : positive polarit… |
| 1.3.6.1.4.1.5040.1.2.48.3.2.1.1.6 | ColumnwtWebio577xxEA1x1PortInputBicountInactivTimeout | read-write | mandatory | Pulse chains with a duration shorter than here specified (in 1/10 sek), are ignored. |
| 1.3.6.1.4.1.5040.1.2.48.3.2.2 | TablewtWebio577xxEA1x1OutputPortTable | not-accessible | mandatory | List of settings depending on the output number. |
| 1.3.6.1.4.1.5040.1.2.48.3.2.2.1 | RowwtWebio577xxEA1x1OutputPortEntry | not-accessible | mandatory | Output parameters of the individual outputs. |
| 1.3.6.1.4.1.5040.1.2.48.3.2.2.1.1 | ColumnwtWebio577xxEA1x1PortOutputName | read-write | mandatory | Name of the output. |
| 1.3.6.1.4.1.5040.1.2.48.3.2.2.1.2 | ColumnwtWebio577xxEA1x1PortOutputText | read-write | mandatory | Description of the output. |
| 1.3.6.1.4.1.5040.1.2.48.3.2.2.1.3 | ColumnwtWebio577xxEA1x1PortOutputGroupMode | read-write | mandatory | It is possible to connect outputs together to increase the output current. This could be done by connecting 2 or 4 outputs in a group together. All bits of suc… |
| 1.3.6.1.4.1.5040.1.2.48.3.2.2.1.4 | ColumnwtWebio577xxEA1x1PortOutputSafetyState | read-write | mandatory | This variable allows setting of individual digital outputs. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds … |
| 1.3.6.1.4.1.5040.1.2.48.3.2.2.1.5 | ColumnwtWebio577xxEA1x1PortLogicInputMask | read-write | mandatory | Selecting one of these inputs by setting the corresponding bit to 1 enables the logic function for the output identified by the index within this table. The ca… |
| 1.3.6.1.4.1.5040.1.2.48.3.2.2.1.6 | ColumnwtWebio577xxEA1x1PortLogicInputInverter | read-write | mandatory | Every input bit selected here will be inverted. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 0-1 : inputs 0-1 |
| 1.3.6.1.4.1.5040.1.2.48.3.2.2.1.7 | ColumnwtWebio577xxEA1x1PortLogicFunction | read-write | mandatory | This determines the logic function. No more than one function may be selected. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 0 : logic function … |
| 1.3.6.1.4.1.5040.1.2.48.3.2.2.1.8 | ColumnwtWebio577xxEA1x1PortLogicOutputInverter | read-write | mandatory | The logical operation result could be inverteted by setting the corresponding bit to 1. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 0 : Output… |
| 1.3.6.1.4.1.5040.1.2.48.3.2.2.1.9 | ColumnwtWebio577xxEA1x1PortPulseDuration | read-write | mandatory | Pulse length in 1/1000 sec. Setting this value to zero, disables the pulse output. |
| 1.3.6.1.4.1.5040.1.2.48.3.2.2.1.10 | ColumnwtWebio577xxEA1x1PortPulsePolarity | read-write | mandatory | This value defines the polarity of the output pulse, if wtWebio577xxEA1x1PortPulseDuration is not set to zero. After the pulse is finished, the output switches… |
| 1.3.6.1.4.1.5040.1.2.48.3.3 | NodewtWebio577xxEA1x1Manufact | |||
| 1.3.6.1.4.1.5040.1.2.48.3.3.1 | ScalarwtWebio577xxEA1x1MfName | read-write | mandatory | Manufacturer company name |
| 1.3.6.1.4.1.5040.1.2.48.3.3.2 | ScalarwtWebio577xxEA1x1MfAddr | read-write | mandatory | Manufacturer address. |
| 1.3.6.1.4.1.5040.1.2.48.3.3.3 | ScalarwtWebio577xxEA1x1MfHotline | read-write | mandatory | Manufacturer hotline. |
| 1.3.6.1.4.1.5040.1.2.48.3.3.4 | ScalarwtWebio577xxEA1x1MfInternet | read-write | mandatory | Manufacturer Internet address. |
| 1.3.6.1.4.1.5040.1.2.48.3.3.5 | ScalarwtWebio577xxEA1x1MfDeviceTyp | read-write | mandatory | Manufacturer device name (model number). |
| 1.3.6.1.4.1.5040.1.2.48.4 | NodewtWebio577xxEA1x1Diag | |||
| 1.3.6.1.4.1.5040.1.2.48.4.1 | ScalarwtWebio577xxEA1x1DiagErrorCount | read-only | mandatory | Number of entries in the error memory. |
| 1.3.6.1.4.1.5040.1.2.48.4.2 | ScalarwtWebio577xxEA1x1DiagBinaryError | read-only | mandatory | Error causes coded bit-by-bit. |
| 1.3.6.1.4.1.5040.1.2.48.4.3 | ScalarwtWebio577xxEA1x1DiagErrorIndex | read-write | mandatory | The value of this variable is used as an index to read an error massege from wtWebio577xxEA1x1DiagErrorMessage. Errors are numbered from 1 to wtWebio577xxEA1x1… |
| 1.3.6.1.4.1.5040.1.2.48.4.4 | ScalarwtWebio577xxEA1x1DiagErrorMessage | read-only | mandatory | Using wtWebio577xxEA1x1DiagErrorIndex as an index, the appropriate message is available. |
| 1.3.6.1.4.1.5040.1.2.48.4.5 | ScalarwtWebio577xxEA1x1DiagErrorClear | write-only | mandatory | Writing 1 into this variable clears all diagnosis messages. |
| 1.3.6.1.4.1.5040.1.2.48.41 | NodewtWebio577xxEA1x1Alert1 | This SNMP trap is generated when Alarm 1 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.48.42 | NodewtWebio577xxEA1x1Alert2 | This SNMP trap is generated when Alarm 2 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.48.43 | NodewtWebio577xxEA1x1Alert3 | This SNMP trap is generated when Alarm 3 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.48.44 | NodewtWebio577xxEA1x1Alert4 | This SNMP trap is generated when Alarm 4 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.48.45 | NodewtWebio577xxEA1x1Alert5 | This SNMP trap is generated when Alarm 5 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.48.46 | NodewtWebio577xxEA1x1Alert6 | This SNMP trap is generated when Alarm 6 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.48.47 | NodewtWebio577xxEA1x1Alert7 | This SNMP trap is generated when Alarm 7 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.48.48 | NodewtWebio577xxEA1x1Alert8 | This SNMP trap is generated when Alarm 8 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.48.49 | NodewtWebio577xxEA1x1Alert9 | This SNMP trap is generated when Alarm 9 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.48.50 | NodewtWebio577xxEA1x1Alert10 | This SNMP trap is generated when Alarm 10 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.48.51 | NodewtWebio577xxEA1x1Alert11 | This SNMP trap is generated when Alarm 11 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.48.52 | NodewtWebio577xxEA1x1Alert12 | This SNMP trap is generated when Alarm 12 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.48.71 | NodewtWebio577xxEA1x1Alert13 | This SNMP trap is generated when Alarm 1 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.48.72 | NodewtWebio577xxEA1x1Alert14 | This SNMP trap is generated when Alarm 2 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.48.73 | NodewtWebio577xxEA1x1Alert15 | This SNMP trap is generated when Alarm 3 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.48.74 | NodewtWebio577xxEA1x1Alert16 | This SNMP trap is generated when Alarm 4 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.48.75 | NodewtWebio577xxEA1x1Alert17 | This SNMP trap is generated when Alarm 5 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.48.76 | NodewtWebio577xxEA1x1Alert18 | This SNMP trap is generated when Alarm 6 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.48.77 | NodewtWebio577xxEA1x1Alert19 | This SNMP trap is generated when Alarm 7 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.48.78 | NodewtWebio577xxEA1x1Alert20 | This SNMP trap is generated when Alarm 8 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.48.79 | NodewtWebio577xxEA1x1Alert21 | This SNMP trap is generated when Alarm 9 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.48.80 | NodewtWebio577xxEA1x1Alert22 | This SNMP trap is generated when Alarm 10 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.48.81 | NodewtWebio577xxEA1x1Alert23 | This SNMP trap is generated when Alarm 11 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.48.82 | NodewtWebio577xxEA1x1Alert24 | This SNMP trap is generated when Alarm 12 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.48.110 | NodewtWebio577xxEA1x1AlertDiag | This SNMP trap is generated when a diagnosis/error message was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.49 | NodewtWebio577xxEA12x12 | |||
| 1.3.6.1.4.1.5040.1.2.49.1 | NodewtWebio577xxEA12x12InOut | |||
| 1.3.6.1.4.1.5040.1.2.49.1.1 | ScalarwtWebio577xxEA12x12Inputs | read-only | mandatory | Number of idependent inputs. |
| 1.3.6.1.4.1.5040.1.2.49.1.2 | ScalarwtWebio577xxEA12x12Outputs | read-only | mandatory | Number of idependent outputs. |
| 1.3.6.1.4.1.5040.1.2.49.1.3 | TablewtWebio577xxEA12x12InputTable | not-accessible | mandatory | List of input indices. |
| 1.3.6.1.4.1.5040.1.2.49.1.3.1 | RowwtWebio577xxEA12x12InputEntry | not-accessible | mandatory | Number of the inputs. |
| 1.3.6.1.4.1.5040.1.2.49.1.3.1.1 | ColumnwtWebio577xxEA12x12InputNo | read-only | mandatory | Index numbers of the inputs. |
| 1.3.6.1.4.1.5040.1.2.49.1.3.1.2 | ColumnwtWebio577xxEA12x12InputCounter | read-only | mandatory | Value of the input counter. |
| 1.3.6.1.4.1.5040.1.2.49.1.3.1.3 | ColumnwtWebio577xxEA12x12InputCounterClear | read-only | mandatory | Clears the input counter after returning its value. |
| 1.3.6.1.4.1.5040.1.2.49.1.3.1.4 | ColumnwtWebio577xxEA12x12InputState | read-only | mandatory | Value of a single input bit, 0-OFF, 1-ON. |
| 1.3.6.1.4.1.5040.1.2.49.1.4 | ScalarwtWebio577xxEA12x12InputValue | read-only | mandatory | This variable is used to read the inputs of the digital I/O port. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corres… |
| 1.3.6.1.4.1.5040.1.2.49.1.5 | TablewtWebio577xxEA12x12OutputTable | not-accessible | mandatory | List of output indices. |
| 1.3.6.1.4.1.5040.1.2.49.1.5.1 | RowwtWebio577xxEA12x12OutputEntry | not-accessible | mandatory | Number of the outputs. |
| 1.3.6.1.4.1.5040.1.2.49.1.5.1.1 | ColumnwtWebio577xxEA12x12OutputNo | read-only | mandatory | Output number. |
| 1.3.6.1.4.1.5040.1.2.49.1.5.1.2 | ColumnwtWebio577xxEA12x12OutputState | read-write | mandatory | Value of a single output bit, 0-OFF, 1-ON. |
| 1.3.6.1.4.1.5040.1.2.49.1.6 | ScalarwtWebio577xxEA12x12OutputValue | read-write | mandatory | This variable is used to read and write the outputs of the digital I/O port. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. B… |
| 1.3.6.1.4.1.5040.1.2.49.1.7 | ScalarwtWebio577xxEA12x12SetOutput | read-write | mandatory | This variable allows setting of individual digital outputs. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds … |
| 1.3.6.1.4.1.5040.1.2.49.2 | NodewtWebio577xxEA12x12SessCntrl | |||
| 1.3.6.1.4.1.5040.1.2.49.2.1 | ScalarwtWebio577xxEA12x12SessCntrlPassword | read-write | mandatory | Entering this password opens a session which is ended by writing a 1 to wtWebio577xxEA12x12SessCntrlLogout. When read this variable provides a string of length… |
| 1.3.6.1.4.1.5040.1.2.49.2.2 | ScalarwtWebio577xxEA12x12SessCntrlConfigMode | read-only | mandatory | When the device is in SNMP configuration mode, the value 1 is returned, otherwise 0. If the read value is 0 even though the password was written, the device is… |
| 1.3.6.1.4.1.5040.1.2.49.2.3 | ScalarwtWebio577xxEA12x12SessCntrlLogout | read-write | mandatory | If the device is in configuration mode and the session was opened by this SNMP Manager, writing a 1 to this variable will end the session and all parameters ar… |
| 1.3.6.1.4.1.5040.1.2.49.2.4 | ScalarwtWebio577xxEA12x12SessCntrlAdminPassword | read-write | mandatory | This password protects access to the variables with administrator rights. It can only be changed by the administrator. If no password was assigned, the valid p… |
| 1.3.6.1.4.1.5040.1.2.49.2.5 | ScalarwtWebio577xxEA12x12SessCntrlConfigPassword | read-write | mandatory | This password protects access to the variables with configurator rights. It can be changed by the administrator and by the configurator. If no password was ass… |
| 1.3.6.1.4.1.5040.1.2.49.3 | NodewtWebio577xxEA12x12Config | |||
| 1.3.6.1.4.1.5040.1.2.49.3.1 | NodewtWebio577xxEA12x12Device | |||
| 1.3.6.1.4.1.5040.1.2.49.3.1.1 | NodewtWebio577xxEA12x12Text | |||
| 1.3.6.1.4.1.5040.1.2.49.3.1.1.1 | ScalarwtWebio577xxEA12x12DeviceName | read-write | mandatory | Name of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.1.2 | ScalarwtWebio577xxEA12x12DeviceText | read-write | mandatory | Description of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.1.3 | ScalarwtWebio577xxEA12x12DeviceLocation | read-write | mandatory | Description of the location of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.1.4 | ScalarwtWebio577xxEA12x12DeviceContact | read-write | mandatory | Contact address of the system operator of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.2 | NodewtWebio577xxEA12x12TimeDate | |||
| 1.3.6.1.4.1.5040.1.2.49.3.1.2.1 | NodewtWebio577xxEA12x12TimeZone | |||
| 1.3.6.1.4.1.5040.1.2.49.3.1.2.1.1 | ScalarwtWebio577xxEA12x12TzOffsetHrs | read-write | mandatory | Offset hours for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.2.1.2 | ScalarwtWebio577xxEA12x12TzOffsetMin | read-write | mandatory | Offset minutes for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.2.1.3 | ScalarwtWebio577xxEA12x12TzEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Timezone |
| 1.3.6.1.4.1.5040.1.2.49.3.1.2.1.4 | ScalarwtWebio577xxEA12x12StTzOffsetHrs | read-write | mandatory | Offset hours of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.2.1.5 | ScalarwtWebio577xxEA12x12StTzOffsetMin | read-write | mandatory | Offset minutes of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.2.1.6 | ScalarwtWebio577xxEA12x12StTzEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Summertime |
| 1.3.6.1.4.1.5040.1.2.49.3.1.2.1.7 | ScalarwtWebio577xxEA12x12StTzStartMonth | read-write | mandatory | Month in which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.2.1.8 | ScalarwtWebio577xxEA12x12StTzStartMode | read-write | mandatory | Mode of the day of the week for which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.2.1.9 | ScalarwtWebio577xxEA12x12StTzStartWday | read-write | mandatory | Day of the week on which the change is made from winter time to summer time |
| 1.3.6.1.4.1.5040.1.2.49.3.1.2.1.10 | ScalarwtWebio577xxEA12x12StTzStartHrs | read-write | mandatory | Hour in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.2.1.11 | ScalarwtWebio577xxEA12x12StTzStartMin | read-write | mandatory | Minute in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.2.1.12 | ScalarwtWebio577xxEA12x12StTzStopMonth | read-write | mandatory | Month in which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.2.1.13 | ScalarwtWebio577xxEA12x12StTzStopMode | read-write | mandatory | Mode of the week day on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.2.1.14 | ScalarwtWebio577xxEA12x12StTzStopWday | read-write | mandatory | Day of the week on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.2.1.15 | ScalarwtWebio577xxEA12x12StTzStopHrs | read-write | mandatory | Hour at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.2.1.16 | ScalarwtWebio577xxEA12x12StTzStopMin | read-write | mandatory | Minute at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.2.2 | NodewtWebio577xxEA12x12TimeServer | |||
| 1.3.6.1.4.1.5040.1.2.49.3.1.2.2.1 | ScalarwtWebio577xxEA12x12TimeServer1 | read-write | mandatory | IP address or name of the 1st time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.49.3.1.2.2.2 | ScalarwtWebio577xxEA12x12TimeServer2 | read-write | mandatory | IP address or name of the 2nd time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.49.3.1.2.2.3 | ScalarwtWebio577xxEA12x12TsEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Time Server |
| 1.3.6.1.4.1.5040.1.2.49.3.1.2.2.4 | ScalarwtWebio577xxEA12x12TsSyncTime | read-write | mandatory | Daily synchronisation time with the time server (hour: 0-23). |
| 1.3.6.1.4.1.5040.1.2.49.3.1.2.3 | NodewtWebio577xxEA12x12DeviceClock | |||
| 1.3.6.1.4.1.5040.1.2.49.3.1.2.3.1 | ScalarwtWebio577xxEA12x12ClockHrs | read-write | mandatory | Clock hours taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.2.3.2 | ScalarwtWebio577xxEA12x12ClockMin | read-write | mandatory | Clock minutes taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.2.3.3 | ScalarwtWebio577xxEA12x12ClockDay | read-write | mandatory | Date: Day of the month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.2.3.4 | ScalarwtWebio577xxEA12x12ClockMonth | read-write | mandatory | Date: Month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.2.3.5 | ScalarwtWebio577xxEA12x12ClockYear | read-write | mandatory | Date: Year, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3 | NodewtWebio577xxEA12x12Basic | |||
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.1 | NodewtWebio577xxEA12x12Network | |||
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.1.1 | ScalarwtWebio577xxEA12x12IpAddress | read-write | mandatory | IP address of the Webio |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.1.2 | ScalarwtWebio577xxEA12x12SubnetMask | read-write | mandatory | Subnet mask of the Webio |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.1.3 | ScalarwtWebio577xxEA12x12Gateway | read-write | mandatory | Gateway of the Webio |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.1.4 | ScalarwtWebio577xxEA12x12DnsServer1 | read-write | mandatory | IP address of the 1st DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.1.5 | ScalarwtWebio577xxEA12x12DnsServer2 | read-write | mandatory | IP address of the 2nd DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.1.6 | ScalarwtWebio577xxEA12x12AddConfig | read-write | mandatory | Additional configuration (1=ON): Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1: DHCP enable Bit 0: BOOTP enable |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.2 | NodewtWebio577xxEA12x12HTTP | |||
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.2.1 | ScalarwtWebio577xxEA12x12Startup | read-write | mandatory | Binary coded start page, more than one page must not be selected: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 2: user.htm Bit 1: home.htm Bit … |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.2.2 | ScalarwtWebio577xxEA12x12GetHeaderEnable | read-write | mandatory | If bits are set, every answer of a short form GET question will be lead by the IP-address and name of the device (Header) or a HTTP header (HTTP): Octet 1: unu… |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.2.3 | ScalarwtWebio577xxEA12x12HttpInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.2.4 | ScalarwtWebio577xxEA12x12HttpPort | read-write | mandatory | Definition of the standard HTML port (Default: 80). |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.3 | NodewtWebio577xxEA12x12Mail | |||
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.3.1 | ScalarwtWebio577xxEA12x12MailAdName | read-write | mandatory | Device name for mail administration. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.3.2 | ScalarwtWebio577xxEA12x12MailReply | read-write | mandatory | Reply address for the mail server. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.3.3 | ScalarwtWebio577xxEA12x12MailServer | read-write | mandatory | Name or IP address of the mail server. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.3.4 | ScalarwtWebio577xxEA12x12MailEnable | read-write | mandatory | Set this bit to enable the sending of mails: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Mail enable |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.3.5 | ScalarwtWebio577xxEA12x12MailAuthentication | read-write | mandatory | Selection of the authentication modi: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTE… |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.3.6 | ScalarwtWebio577xxEA12x12MailAuthUser | read-write | mandatory | Name of the user to be authenticated. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.3.7 | ScalarwtWebio577xxEA12x12MailAuthPassword | read-write | mandatory | Authentication password. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.3.8 | ScalarwtWebio577xxEA12x12MailPop3Server | read-write | mandatory | Name or Ip-address of the POP3 Servers. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.4 | NodewtWebio577xxEA12x12SNMP | |||
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.4.1 | ScalarwtWebio577xxEA12x12SnmpEnable | read-write | mandatory | Set bit 0 to enable SNMP. If disabled, the device did not respond to any SNMP requests. Bit 1 decided wether the community string of read operations is compare… |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.4.2 | ScalarwtWebio577xxEA12x12SnmpCommunityStringRead | read-write | mandatory | Community string read only |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.4.3 | ScalarwtWebio577xxEA12x12SnmpCommunityStringReadWrite | read-write | mandatory | Community string read / write |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.4.4 | ScalarwtWebio577xxEA12x12SnmpSystemTrapManagerIP | read-write | mandatory | Name or IP address of the TCP server which accepts the system trap. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.4.5 | ScalarwtWebio577xxEA12x12SnmpSystemTrapEnable | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2: Diag messages Bit 3-7: unused |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.4.6 | ScalarwtWebio577xxEA12x12SnmpSystemTrapManagerPort | read-write | mandatory | Port number of the TCP server which accepts the system trap. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.5 | NodewtWebio577xxEA12x12UDP | |||
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.5.1 | ScalarwtWebio577xxEA12x12UdpAdminPort | read-write | mandatory | Udp port to which the Udp queries ( short form GET requests) can be sent. This port number must be unique within the device. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.5.2 | ScalarwtWebio577xxEA12x12UdpEnable | read-write | mandatory | Set this bit to enable UDP support: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : UDP enable |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.5.3 | ScalarwtWebio577xxEA12x12UdpRemotePort | read-write | mandatory | Udp remote port setting. If this value is set to zero, the source port read from a request will be used as destination port for the answer. A non zero value fo… |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.6 | NodewtWebio577xxEA12x12Binary | |||
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.6.1 | ScalarwtWebio577xxEA12x12BinaryModeCount | read-only | mandatory | Number of independent binary channels. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.6.2 | TablewtWebio577xxEA12x12BinaryIfTable | not-accessible | mandatory | Table of indices. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.6.2.1 | RowwtWebio577xxEA12x12BinaryIfEntry | not-accessible | mandatory | Indices of the binary channels. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.6.2.1.1 | ColumnwtWebio577xxEA12x12BinaryModeNo | read-only | mandatory | Number of the binary channel. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.6.3 | TablewtWebio577xxEA12x12BinaryTable | not-accessible | mandatory | Table of properties of the binary mode. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.6.3.1 | RowwtWebio577xxEA12x12BinaryEntry | not-accessible | mandatory | Binary properties. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.6.3.1.1 | ColumnwtWebio577xxEA12x12BinaryOperationMode | read-write | mandatory | Selection of the operation mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: … |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.6.3.1.2 | ColumnwtWebio577xxEA12x12BinaryTcpServerLocalPort | read-write | mandatory | Local TCP port for data exchange in this server mode. This port number must be unique within the device. Reserved port number must not be used (refere to the m… |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.6.3.1.3 | ColumnwtWebio577xxEA12x12BinaryTcpServerInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.6.3.1.4 | ColumnwtWebio577xxEA12x12BinaryTcpServerApplicationMode | read-write | mandatory | Selection of the application mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4… |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.6.3.1.5 | ColumnwtWebio577xxEA12x12BinaryTcpClientLocalPort | read-write | mandatory | Local TCP port for data exchange in this client mode. This port number must be unique within the device. Reserved port number must not be used (refere to the m… |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.6.3.1.6 | ColumnwtWebio577xxEA12x12BinaryTcpClientServerPort | read-write | mandatory | Port number of the server. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when setting t… |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.6.3.1.7 | ColumnwtWebio577xxEA12x12BinaryTcpClientServerIpAddr | read-write | mandatory | Ip address of the server. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when setting th… |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.6.3.1.8 | ColumnwtWebio577xxEA12x12BinaryTcpClientServerPassword | read-write | mandatory | Building a connection may be protected by the administrator password of the server. Enter the server password to establish the connection, if a server administ… |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.6.3.1.9 | ColumnwtWebio577xxEA12x12BinaryTcpClientInactivity | read-write | mandatory | Connection timeout in 100ms. If no data are exchanged within the specified time, the device closes the connection to the server. The value 0 deactivates the ti… |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.6.3.1.10 | ColumnwtWebio577xxEA12x12BinaryTcpClientInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.6.3.1.11 | ColumnwtWebio577xxEA12x12BinaryTcpClientInterval | read-write | mandatory | Configurable interval with a 100ms base, in which the Webio device sends data to the configured application. A interval of zero stopps the periodical sending. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.6.3.1.12 | ColumnwtWebio577xxEA12x12BinaryTcpClientApplicationMode | read-write | mandatory | Selection of the application mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4… |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.6.3.1.13 | ColumnwtWebio577xxEA12x12BinaryUdpPeerLocalPort | read-write | mandatory | Local UDP port for data exchange in this peer to peer mode. This port number must be unique within the device. Reserved port number must not be used (refere to… |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.6.3.1.14 | ColumnwtWebio577xxEA12x12BinaryUdpPeerRemotePort | read-write | mandatory | Port number of the remote device. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when se… |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.6.3.1.15 | ColumnwtWebio577xxEA12x12BinaryUdpPeerRemoteIpAddr | read-write | mandatory | Ip address of the remote device. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when set… |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.6.3.1.16 | ColumnwtWebio577xxEA12x12BinaryUdpPeerInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.6.3.1.17 | ColumnwtWebio577xxEA12x12BinaryUdpPeerInterval | read-write | mandatory | Configurable interval with a 100ms base, in which the Webio device sends data to the configured remote device. A interval of zero stopps the periodical sending. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.6.3.1.18 | ColumnwtWebio577xxEA12x12BinaryUdpPeerApplicationMode | read-write | mandatory | Selection of the application mode: The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds to the LSB. OCTET 1: unus… |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.6.3.1.19 | ColumnwtWebio577xxEA12x12BinaryConnectedPort | read-only | mandatory | Port number of the remote device, after connection has been established. In case of no connection or missing port informations a zero will be read. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.6.3.1.20 | ColumnwtWebio577xxEA12x12BinaryConnectedIpAddr | read-only | mandatory | IP address of the remote device, after connection has been established. In case of no connection or missing port informations 0.0.0.0 will be read. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.6.3.1.21 | ColumnwtWebio577xxEA12x12BinaryTcpServerClientHttpPort | read-write | mandatory | HTTP port number of the remote device at TCP Server Mode. If an mailfunction occurs status informations will be send to this port. Not used at mode Compatible … |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.6.3.1.22 | ColumnwtWebio577xxEA12x12BinaryTcpClientServerHttpPort | read-write | mandatory | HTTP port number of the remote device at TCP Client Mode. In the operating mode Box2Box connection status informations will be exchanged through this port. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.6.3.1.23 | ColumnwtWebio577xxEA12x12BinaryTcpClientServerUserName | read-only | mandatory | User Name to login at the remote server, if authentication needed. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.7 | NodewtWebio577xxEA12x12Syslog | |||
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.7.1 | ScalarwtWebio577xxEA12x12SyslogServerIP | read-write | mandatory | Name or IP address of the Syslog server, which accepts the Syslog messgaes. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.7.2 | ScalarwtWebio577xxEA12x12SyslogServerPort | read-write | mandatory | Portnumber of the Syslog servers, default 514. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.7.3 | ScalarwtWebio577xxEA12x12SyslogSystemMessagesEnable | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2: Diag Messages Bit 3-7: unused |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.7.4 | ScalarwtWebio577xxEA12x12SyslogEnable | read-write | mandatory | Set bit 0to enable Syslog: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Syslog enable |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.8 | NodewtWebio577xxEA12x12FTP | |||
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.8.1 | ScalarwtWebio577xxEA12x12FTPServerIP | read-write | mandatory | Name or IP address of the FTP server, which accepts the FTP messages. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.8.2 | ScalarwtWebio577xxEA12x12FTPServerControlPort | read-write | mandatory | Portnumber of the control port of the FTP server, default 21. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.8.3 | ScalarwtWebio577xxEA12x12FTPUserName | read-write | mandatory | FTP Loggin: user name. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.8.4 | ScalarwtWebio577xxEA12x12FTPPassword | read-write | mandatory | FTP Loggin: user password. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.8.5 | ScalarwtWebio577xxEA12x12FTPAccount | read-write | mandatory | FTP Loggin: name of account. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.8.6 | ScalarwtWebio577xxEA12x12FTPOption | read-write | mandatory | Bit 0 switches the FTP Server in Passiv-Mode, the Client controls the data connection on its own: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit … |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.8.7 | ScalarwtWebio577xxEA12x12FTPEnable | read-write | mandatory | Set Bit 0 to enable FTP: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : FTP enable |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.12 | NodewtWebio577xxEA12x12MQTT | |||
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.12.1 | ScalarwtWebio577xxEA12x12MQTTEnable | read-write | mandatory | Bit 7 enables MQTT: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0-6: unused Bit 7 : MQTT enable |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.12.2 | ScalarwtWebio577xxEA12x12MQTTBrockerIP | read-write | mandatory | Name or IP-address of the MQTT-Server. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.12.3 | ScalarwtWebio577xxEA12x12MQTTUserName | read-write | mandatory | MQTT login user name. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.12.4 | ScalarwtWebio577xxEA12x12MQTTPassword | read-write | mandatory | MQTT login password. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.12.5 | ScalarwtWebio577xxEA12x12MQTTLocalPort | read-write | mandatory | Local port number. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.12.6 | ScalarwtWebio577xxEA12x12MQTTBrokerServerPort | read-write | mandatory | MQTT Server port number. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.12.7 | ScalarwtWebio577xxEA12x12MQTTInterval | read-write | mandatory | Ping intervall, if no data has to be send: time in seconds. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.12.8 | ScalarwtWebio577xxEA12x12MQTTLastWillEnable | read-write | mandatory | Bit 0 activate MQTT LastWill message: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : MQTT Last will enable |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.12.9 | ScalarwtWebio577xxEA12x12MQTTLastWillTopic | read-write | mandatory | MQTT Last Will Topic. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.12.10 | ScalarwtWebio577xxEA12x12MQTTLastWillMsg | read-write | mandatory | MQTT Last Will message. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.12.11 | ScalarwtWebio577xxEA12x12MQTTLastWillQoS | read-write | mandatory | Binary coded MQTT Publish QoS: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: QoS 0 Bit 1: QoS 1 Bit 2: QoS 2 Bit 3-7:unused |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.12.12 | ScalarwtWebio577xxEA12x12MQTTLastWillRetain | read-write | mandatory | Binary coded MQTT Publish Retain properties: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0 : retain enable Bit 1-7 : unused |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.12.13 | ScalarwtWebio577xxEA12x12MQTTLastWillConnectEnable | read-write | mandatory | Bit 0 activate MQTT LastWill Connect message: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : MQTT Last will connect message e… |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.12.14 | ScalarwtWebio577xxEA12x12MQTTLastWillConnectMsg | read-write | mandatory | MQTT Last Will Connect message will be send with the QoS and Retain settings of the LastWill message. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.13 | NodewtWebio577xxEA12x12REST | |||
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.13.1 | ScalarwtWebio577xxEA12x12RESTEnable | read-write | mandatory | Bit 0 activates REST: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : REST enable |
| 1.3.6.1.4.1.5040.1.2.49.3.1.3.13.2 | ScalarwtWebio577xxEA12x12RESTDigestAuthEnable | read-write | mandatory | Bit 0 activates Digest-Authentification: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Digest Auth enable |
| 1.3.6.1.4.1.5040.1.2.49.3.1.4 | NodewtWebio577xxEA12x12OutputMode | |||
| 1.3.6.1.4.1.5040.1.2.49.3.1.4.1 | TablewtWebio577xxEA12x12OutputModeTable | not-accessible | mandatory | Table of output mode configurations dependent on the output indices. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.4.1.1 | RowwtWebio577xxEA12x12OutputModeEntry | not-accessible | mandatory | Output mode configurations of the individual outputs. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.4.1.1.1 | ColumnwtWebio577xxEA12x12OutputModeBit | read-write | mandatory | This binary coded output mode defines the individual operation mode for any output. More than one mode must not be selected. The OCTETS are interpreted bit-by-… |
| 1.3.6.1.4.1.5040.1.2.49.3.1.4.2 | ScalarwtWebio577xxEA12x12SafetyTimeout | read-write | mandatory | After this period of time (multiple of 100ms) without receiving data outputs switch to their Safety States. For each output a independend safety state could be… |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5 | NodewtWebio577xxEA12x12Alarm | |||
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.1 | ScalarwtWebio577xxEA12x12AlarmCount | read-only | mandatory | Number of independent alarms. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.2 | TablewtWebio577xxEA12x12AlarmIfTable | not-accessible | mandatory | List of alarm indices. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.2.1 | RowwtWebio577xxEA12x12AlarmIfEntry | not-accessible | mandatory | Numbers of the alarms. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.2.1.1 | ColumnwtWebio577xxEA12x12AlarmNo | read-only | mandatory | Numbers of the alarms. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3 | TablewtWebio577xxEA12x12AlarmTable | not-accessible | mandatory | List of settings depending on the alarm number. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1 | RowwtWebio577xxEA12x12AlarmEntry | not-accessible | mandatory | Alarm parameters of the individual alarms. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.1 | ColumnwtWebio577xxEA12x12AlarmInputTrigger | read-write | mandatory | This variable allows setting of individual input trigger conditions. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an input. Bit 0 corr… |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.2 | ColumnwtWebio577xxEA12x12AlarmOutputTrigger | read-write | mandatory | This variable allows setting of individual output trigger conditions. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 co… |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.3 | ColumnwtWebio577xxEA12x12AlarmSystemTrigger | read-write | mandatory | Binary coded trigger conditions: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, … |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.4 | ColumnwtWebio577xxEA12x12AlarmMaxCounterValue | read-write | mandatory | This variable configures a max. counter value. If an input counter value exceeds this max. value, the corresponding alarm is triggered. Input counters with its… |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.5 | ColumnwtWebio577xxEA12x12AlarmInterval | read-write | mandatory | Send interval for alarm messages. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.6 | ColumnwtWebio577xxEA12x12AlarmEnable | read-write | mandatory | Binary coded alarm enable: Octet 1: unused Octet 2: unused Bit 0: UDP enable Bit1-7: unused Octet 4: Bit 0: Mail Enable Bit 1: SNMP Trap enable Bit 2: TCP Clie… |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.7 | ColumnwtWebio577xxEA12x12AlarmMailAddr | read-write | mandatory | E-Mail address for sending the alarm mail to. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.8 | ColumnwtWebio577xxEA12x12AlarmMailSubject | read-write | mandatory | Subject line for alarm mail. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.9 | ColumnwtWebio577xxEA12x12AlarmMailText | read-write | mandatory | Alarm mail text: States of the Webio device can be included by using special tags. Please refer to the respective Webio manual |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.10 | ColumnwtWebio577xxEA12x12AlarmSnmpManagerIP | read-write | mandatory | IP address of the SNMP Manager to which the Webio device should send SNMP traps. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.11 | ColumnwtWebio577xxEA12x12AlarmSnmpTrapText | read-write | mandatory | This text appears in the trap body. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.12 | ColumnwtWebio577xxEA12x12AlarmUdpIpAddr | read-write | mandatory | IP address of the UDP listener to which the Webio device should send UDP traps. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.13 | ColumnwtWebio577xxEA12x12AlarmUdpPort | read-write | mandatory | Port number of the UDP listener to which the Webio device should send UDP traps. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.14 | ColumnwtWebio577xxEA12x12AlarmUdpText | read-write | mandatory | This text appears in the UDP trap body. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.15 | ColumnwtWebio577xxEA12x12AlarmTcpIpAddr | read-write | mandatory | IP address of the TCP listener to which the Webio device should send TCP traps. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.16 | ColumnwtWebio577xxEA12x12AlarmTcpPort | read-write | mandatory | Port number of the TCP listener to which the Webio device should send TCP traps. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.17 | ColumnwtWebio577xxEA12x12AlarmTcpText | read-write | mandatory | This text appears in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.18 | ColumnwtWebio577xxEA12x12AlarmSyslogIpAddr | read-write | mandatory | IP address of the syslog server to which the Webio device should send syslog messages. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.19 | ColumnwtWebio577xxEA12x12AlarmSyslogPort | read-write | mandatory | Port number of the syslog server to which the Webio device should send syslog messages. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.20 | ColumnwtWebio577xxEA12x12AlarmSyslogText | read-write | mandatory | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.21 | ColumnwtWebio577xxEA12x12AlarmFtpDataPort | read-write | mandatory | Local data port: 1..65535 or AUTO: the next free port will be assigned. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.22 | ColumnwtWebio577xxEA12x12AlarmFtpFileName | read-write | mandatory | Name of the file including path informations. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.23 | ColumnwtWebio577xxEA12x12AlarmFtpText | read-write | mandatory | Message text to store on the FTP server. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.24 | ColumnwtWebio577xxEA12x12AlarmFtpOption | read-write | mandatory | Binary coded options, select only one option at the same time: STORE = replace file APPEND = append message at the end of the file Octet 1: unused Octet 2: unu… |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.25 | ColumnwtWebio577xxEA12x12AlarmTimerCron | read-write | mandatory | This entry contains 5 space or tab seperated text fields for time trigger definition. Each field must match with the actual time to trigger a message, weekday … |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.26 | ColumnwtWebio577xxEA12x12AlarmMailReleaseSubject | read-write | mandatory | Subject line for alarm mail. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.27 | ColumnwtWebio577xxEA12x12AlarmMailReleaseText | read-write | mandatory | Release Alarm mail text: States of the Webio device can be included by using special tags. Please refer to the respective Webio manual |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.28 | ColumnwtWebio577xxEA12x12AlarmSnmpTrapReleaseText | read-write | mandatory | This text appears in the trap body. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.29 | ColumnwtWebio577xxEA12x12AlarmUdpReleaseText | read-write | mandatory | This text appears in the UDP trap body. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.30 | ColumnwtWebio577xxEA12x12AlarmTcpReleaseText | read-write | mandatory | This text appears in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.31 | ColumnwtWebio577xxEA12x12AlarmSyslogReleaseText | read-write | mandatory | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.32 | ColumnwtWebio577xxEA12x12AlarmFtpReleaseText | read-write | mandatory | Message text to store on the FTP server. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.34 | ColumnwtWebio577xxEA12x12AlarmGlobalEnable | read-write | mandatory | Binary coded alarm activation: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bi… |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.58 | ColumnwtWebio577xxEA12x12AlarmCombinationLogic | read-write | mandatory | Binary coded logic, all Input/Output-trigger will be combined: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: un… |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.59 | ColumnwtWebio577xxEA12x12AlarmTrgMqttTopic | read-write | mandatory | MQTT subscribe topic. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.60 | ColumnwtWebio577xxEA12x12AlarmTrgMqttTopicText | read-write | mandatory | Receiving this text from the MQTT Broker, Alarm will be triggered. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.61 | ColumnwtWebio577xxEA12x12AlarmHttpReqAuthEnable | read-write | mandatory | Binary coded value: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bit 1-7: unus… |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.62 | ColumnwtWebio577xxEA12x12AlarmHttpReqAuthUser | read-write | mandatory | HTTP Request: User |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.63 | ColumnwtWebio577xxEA12x12AlarmHttpReqAuthPassword | read-write | mandatory | HTTP Request: Password |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.64 | ColumnwtWebio577xxEA12x12AlarmHttpReqSetUrl | read-write | mandatory | HTTP Request: Set URL |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.65 | ColumnwtWebio577xxEA12x12AlarmHttpReqClearUrl | read-write | mandatory | HTTP Request: Clear URL |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.66 | ColumnwtWebio577xxEA12x12AlarmHttpReqServerPort | read-write | mandatory | HTTP Request: Server Port |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.67 | ColumnwtWebio577xxEA12x12AlarmMqttTopicPath | read-write | mandatory | MQTT Publish: Topic path |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.68 | ColumnwtWebio577xxEA12x12AlarmMqttTopicSetTopic | read-write | mandatory | MQTT Publish: Topic SET message |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.69 | ColumnwtWebio577xxEA12x12AlarmMqttTopicClear | read-write | mandatory | MQTT Publish: Topic CLEAR message |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.70 | ColumnwtWebio577xxEA12x12AlarmSetOutputsOwn | read-write | mandatory | This variable allows setting of individual output. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds to the LS… |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.71 | ColumnwtWebio577xxEA12x12AlarmSetOutputsServerIp | read-write | mandatory | Set Outputs: Server IP Address |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.72 | ColumnwtWebio577xxEA12x12AlarmSetOutputsServerPort | read-write | mandatory | Set Outputs: Server Port |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.73 | ColumnwtWebio577xxEA12x12AlarmSetOutputsServerPassword | read-write | mandatory | Set Outputs: Server Pasword |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.74 | ColumnwtWebio577xxEA12x12AlarmSetOutputsServerOutputs | read-write | mandatory | This variable allows setting of individual output. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds to the LS… |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.75 | ColumnwtWebio577xxEA12x12AlarmSetOutputsDest | read-write | mandatory | Binary coded value: Bit 0 = LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bit 2-7: unused Bit 1 : set outputs of remote server. Bit 0 : set out… |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.76 | ColumnwtWebio577xxEA12x12AlarmSnmpManagerPort | read-write | mandatory | Port number of the SNMP Manager to which the Webio device should send SNMP traps. |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.77 | ColumnwtWebio577xxEA12x12AlarmMqttQoS | read-write | mandatory | Binary coded value: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: QoS 0 Bit 1: QoS 1 Bit 2: QoS 2 Bit 3-7:unused |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.3.1.78 | ColumnwtWebio577xxEA12x12AlarmMqttRetain | read-write | mandatory | Binary coded value: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0 : retain enable Bit 1-7 : unused |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.4 | ScalarwtWebio577xxEA12x12LoadControlView | read-only | mandatory | Here the result of automatic load control can be read. All output were tested in pairs (0-1). If an error occours at one output, both output of an pair will be… |
| 1.3.6.1.4.1.5040.1.2.49.3.1.5.5 | ScalarwtWebio577xxEA12x12LCShutDownView | read-write | mandatory | Here the result of the automatic load control shut down can be read. All outputs remain switched of, until a zero is written into this variable. But previously… |
| 1.3.6.1.4.1.5040.1.2.49.3.2 | NodewtWebio577xxEA12x12Ports | |||
| 1.3.6.1.4.1.5040.1.2.49.3.2.1 | TablewtWebio577xxEA12x12InputPortTable | not-accessible | mandatory | List of settings depending on the input number. |
| 1.3.6.1.4.1.5040.1.2.49.3.2.1.1 | RowwtWebio577xxEA12x12InputPortEntry | not-accessible | mandatory | Input parameter for the individual inputs. |
| 1.3.6.1.4.1.5040.1.2.49.3.2.1.1.1 | ColumnwtWebio577xxEA12x12PortInputName | read-write | mandatory | Name of the input. |
| 1.3.6.1.4.1.5040.1.2.49.3.2.1.1.2 | ColumnwtWebio577xxEA12x12PortInputText | read-write | mandatory | Description of the input. |
| 1.3.6.1.4.1.5040.1.2.49.3.2.1.1.3 | ColumnwtWebio577xxEA12x12PortInputMode | read-write | mandatory | Binary coded modes: Selecting short pulse detection enable by setting the corresponding bit to 1 enables interrupt support for counting. Only positive edges ar… |
| 1.3.6.1.4.1.5040.1.2.49.3.2.1.1.4 | ColumnwtWebio577xxEA12x12PortInputFilter | read-write | mandatory | Pulses with a duration shorter than here specified (duration in 1/1000 sec), are ignored. |
| 1.3.6.1.4.1.5040.1.2.49.3.2.1.1.5 | ColumnwtWebio577xxEA12x12PortInputBicountPulsePolarity | read-write | mandatory | This value defines the polarity of the input pulse. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 0 : negative polarity Bit 1 : positive polarit… |
| 1.3.6.1.4.1.5040.1.2.49.3.2.1.1.6 | ColumnwtWebio577xxEA12x12PortInputBicountInactivTimeout | read-write | mandatory | Pulse chains with a duration shorter than here specified (in 1/10 sek), are ignored. |
| 1.3.6.1.4.1.5040.1.2.49.3.2.2 | TablewtWebio577xxEA12x12OutputPortTable | not-accessible | mandatory | List of settings depending on the output number. |
| 1.3.6.1.4.1.5040.1.2.49.3.2.2.1 | RowwtWebio577xxEA12x12OutputPortEntry | not-accessible | mandatory | Output parameters of the individual outputs. |
| 1.3.6.1.4.1.5040.1.2.49.3.2.2.1.1 | ColumnwtWebio577xxEA12x12PortOutputName | read-write | mandatory | Name of the output. |
| 1.3.6.1.4.1.5040.1.2.49.3.2.2.1.2 | ColumnwtWebio577xxEA12x12PortOutputText | read-write | mandatory | Description of the output. |
| 1.3.6.1.4.1.5040.1.2.49.3.2.2.1.3 | ColumnwtWebio577xxEA12x12PortOutputGroupMode | read-write | mandatory | It is possible to connect outputs together to increase the output current. This could be done by connecting 2 or 4 outputs in a group together. All bits of suc… |
| 1.3.6.1.4.1.5040.1.2.49.3.2.2.1.4 | ColumnwtWebio577xxEA12x12PortOutputSafetyState | read-write | mandatory | This variable allows setting of individual digital outputs. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds … |
| 1.3.6.1.4.1.5040.1.2.49.3.2.2.1.5 | ColumnwtWebio577xxEA12x12PortLogicInputMask | read-write | mandatory | Selecting one of these inputs by setting the corresponding bit to 1 enables the logic function for the output identified by the index within this table. The ca… |
| 1.3.6.1.4.1.5040.1.2.49.3.2.2.1.6 | ColumnwtWebio577xxEA12x12PortLogicInputInverter | read-write | mandatory | Every input bit selected here will be inverted. OCTET 1: unused OCTET 2: unused OCTET 3: Bit 0-3 : inputs 8-11 OCTET 4: Bit 0-7 : inputs 0-7 |
| 1.3.6.1.4.1.5040.1.2.49.3.2.2.1.7 | ColumnwtWebio577xxEA12x12PortLogicFunction | read-write | mandatory | This determines the logic function. No more than one function may be selected. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 0 : logic function … |
| 1.3.6.1.4.1.5040.1.2.49.3.2.2.1.8 | ColumnwtWebio577xxEA12x12PortLogicOutputInverter | read-write | mandatory | The logical operation result could be inverteted by setting the corresponding bit to 1. OCTET 1: unused OCTET 2: unused OCTET 3: Bit 0-3 : Output Inverter enab… |
| 1.3.6.1.4.1.5040.1.2.49.3.2.2.1.9 | ColumnwtWebio577xxEA12x12PortPulseDuration | read-write | mandatory | Pulse length in 1/1000 sec. Setting this value to zero, disables the pulse output. |
| 1.3.6.1.4.1.5040.1.2.49.3.2.2.1.10 | ColumnwtWebio577xxEA12x12PortPulsePolarity | read-write | mandatory | This value defines the polarity of the output pulse, if wtWebio577xxEA12x12PortPulseDuration is not set to zero. After the pulse is finished, the output switch… |
| 1.3.6.1.4.1.5040.1.2.49.3.3 | NodewtWebio577xxEA12x12Manufact | |||
| 1.3.6.1.4.1.5040.1.2.49.3.3.1 | ScalarwtWebio577xxEA12x12MfName | read-write | mandatory | Manufacturer company name |
| 1.3.6.1.4.1.5040.1.2.49.3.3.2 | ScalarwtWebio577xxEA12x12MfAddr | read-write | mandatory | Manufacturer address. |
| 1.3.6.1.4.1.5040.1.2.49.3.3.3 | ScalarwtWebio577xxEA12x12MfHotline | read-write | mandatory | Manufacturer hotline. |
| 1.3.6.1.4.1.5040.1.2.49.3.3.4 | ScalarwtWebio577xxEA12x12MfInternet | read-write | mandatory | Manufacturer Internet address. |
| 1.3.6.1.4.1.5040.1.2.49.3.3.5 | ScalarwtWebio577xxEA12x12MfDeviceTyp | read-write | mandatory | Manufacturer device name (model number). |
| 1.3.6.1.4.1.5040.1.2.49.4 | NodewtWebio577xxEA12x12Diag | |||
| 1.3.6.1.4.1.5040.1.2.49.4.1 | ScalarwtWebio577xxEA12x12DiagErrorCount | read-only | mandatory | Number of entries in the error memory. |
| 1.3.6.1.4.1.5040.1.2.49.4.2 | ScalarwtWebio577xxEA12x12DiagBinaryError | read-only | mandatory | Error causes coded bit-by-bit. |
| 1.3.6.1.4.1.5040.1.2.49.4.3 | ScalarwtWebio577xxEA12x12DiagErrorIndex | read-write | mandatory | The value of this variable is used as an index to read an error massege from wtWebio577xxEA12x12DiagErrorMessage. Errors are numbered from 1 to wtWebio577xxEA1… |
| 1.3.6.1.4.1.5040.1.2.49.4.4 | ScalarwtWebio577xxEA12x12DiagErrorMessage | read-only | mandatory | Using wtWebio577xxEA12x12DiagErrorIndex as an index, the appropriate message is available. |
| 1.3.6.1.4.1.5040.1.2.49.4.5 | ScalarwtWebio577xxEA12x12DiagErrorClear | write-only | mandatory | Writing 1 into this variable clears all diagnosis messages. |
| 1.3.6.1.4.1.5040.1.2.49.41 | NodewtWebio577xxEA12x12Alert1 | This SNMP trap is generated when Alarm 1 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.49.42 | NodewtWebio577xxEA12x12Alert2 | This SNMP trap is generated when Alarm 2 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.49.43 | NodewtWebio577xxEA12x12Alert3 | This SNMP trap is generated when Alarm 3 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.49.44 | NodewtWebio577xxEA12x12Alert4 | This SNMP trap is generated when Alarm 4 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.49.45 | NodewtWebio577xxEA12x12Alert5 | This SNMP trap is generated when Alarm 5 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.49.46 | NodewtWebio577xxEA12x12Alert6 | This SNMP trap is generated when Alarm 6 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.49.47 | NodewtWebio577xxEA12x12Alert7 | This SNMP trap is generated when Alarm 7 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.49.48 | NodewtWebio577xxEA12x12Alert8 | This SNMP trap is generated when Alarm 8 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.49.49 | NodewtWebio577xxEA12x12Alert9 | This SNMP trap is generated when Alarm 9 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.49.50 | NodewtWebio577xxEA12x12Alert10 | This SNMP trap is generated when Alarm 10 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.49.51 | NodewtWebio577xxEA12x12Alert11 | This SNMP trap is generated when Alarm 11 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.49.52 | NodewtWebio577xxEA12x12Alert12 | This SNMP trap is generated when Alarm 12 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.49.71 | NodewtWebio577xxEA12x12Alert13 | This SNMP trap is generated when Alarm 1 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.49.72 | NodewtWebio577xxEA12x12Alert14 | This SNMP trap is generated when Alarm 2 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.49.73 | NodewtWebio577xxEA12x12Alert15 | This SNMP trap is generated when Alarm 3 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.49.74 | NodewtWebio577xxEA12x12Alert16 | This SNMP trap is generated when Alarm 4 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.49.75 | NodewtWebio577xxEA12x12Alert17 | This SNMP trap is generated when Alarm 5 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.49.76 | NodewtWebio577xxEA12x12Alert18 | This SNMP trap is generated when Alarm 6 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.49.77 | NodewtWebio577xxEA12x12Alert19 | This SNMP trap is generated when Alarm 7 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.49.78 | NodewtWebio577xxEA12x12Alert20 | This SNMP trap is generated when Alarm 8 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.49.79 | NodewtWebio577xxEA12x12Alert21 | This SNMP trap is generated when Alarm 9 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.49.80 | NodewtWebio577xxEA12x12Alert22 | This SNMP trap is generated when Alarm 10 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.49.81 | NodewtWebio577xxEA12x12Alert23 | This SNMP trap is generated when Alarm 11 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.49.82 | NodewtWebio577xxEA12x12Alert24 | This SNMP trap is generated when Alarm 12 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.49.110 | NodewtWebio577xxEA12x12AlertDiag | This SNMP trap is generated when a diagnosis/error message was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.50 | NodewtWebio577xxEA12x12Uart | |||
| 1.3.6.1.4.1.5040.1.2.51 | NodewtWebio577xxEA12x6Rel | |||
| 1.3.6.1.4.1.5040.1.2.51.1 | NodewtWebio577xxEA12x6RelInOut | |||
| 1.3.6.1.4.1.5040.1.2.51.1.1 | ScalarwtWebio577xxEA12x6RelInputs | read-only | mandatory | Number of idependent inputs. |
| 1.3.6.1.4.1.5040.1.2.51.1.2 | ScalarwtWebio577xxEA12x6RelOutputs | read-only | mandatory | Number of idependent outputs. |
| 1.3.6.1.4.1.5040.1.2.51.1.3 | TablewtWebio577xxEA12x6RelInputTable | not-accessible | mandatory | List of input indices. |
| 1.3.6.1.4.1.5040.1.2.51.1.3.1 | RowwtWebio577xxEA12x6RelInputEntry | not-accessible | mandatory | Number of the inputs. |
| 1.3.6.1.4.1.5040.1.2.51.1.3.1.1 | ColumnwtWebio577xxEA12x6RelInputNo | read-only | mandatory | Index numbers of the inputs. |
| 1.3.6.1.4.1.5040.1.2.51.1.3.1.2 | ColumnwtWebio577xxEA12x6RelInputCounter | read-only | mandatory | Value of the input counter. |
| 1.3.6.1.4.1.5040.1.2.51.1.3.1.3 | ColumnwtWebio577xxEA12x6RelInputCounterClear | read-only | mandatory | Clears the input counter after returning its value. |
| 1.3.6.1.4.1.5040.1.2.51.1.3.1.4 | ColumnwtWebio577xxEA12x6RelInputState | read-only | mandatory | Value of a single input bit, 0-OFF, 1-ON. |
| 1.3.6.1.4.1.5040.1.2.51.1.4 | ScalarwtWebio577xxEA12x6RelInputValue | read-only | mandatory | This variable is used to read the inputs of the digital I/O port. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corres… |
| 1.3.6.1.4.1.5040.1.2.51.1.5 | TablewtWebio577xxEA12x6RelOutputTable | not-accessible | mandatory | List of output indices. |
| 1.3.6.1.4.1.5040.1.2.51.1.5.1 | RowwtWebio577xxEA12x6RelOutputEntry | not-accessible | mandatory | Number of the outputs. |
| 1.3.6.1.4.1.5040.1.2.51.1.5.1.1 | ColumnwtWebio577xxEA12x6RelOutputNo | read-only | mandatory | Output number. |
| 1.3.6.1.4.1.5040.1.2.51.1.5.1.2 | ColumnwtWebio577xxEA12x6RelOutputState | read-write | mandatory | Value of a single output bit, 0-OFF, 1-ON. |
| 1.3.6.1.4.1.5040.1.2.51.1.6 | ScalarwtWebio577xxEA12x6RelOutputValue | read-write | mandatory | This variable is used to read and write the outputs of the digital I/O port. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. B… |
| 1.3.6.1.4.1.5040.1.2.51.1.7 | ScalarwtWebio577xxEA12x6RelSetOutput | read-write | mandatory | This variable allows setting of individual digital outputs. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds … |
| 1.3.6.1.4.1.5040.1.2.51.2 | NodewtWebio577xxEA12x6RelSessCntrl | |||
| 1.3.6.1.4.1.5040.1.2.51.2.1 | ScalarwtWebio577xxEA12x6RelSessCntrlPassword | read-write | mandatory | Entering this password opens a session which is ended by writing a 1 to wtWebio577xxEA12x6RelSessCntrlLogout. When read this variable provides a string of leng… |
| 1.3.6.1.4.1.5040.1.2.51.2.2 | ScalarwtWebio577xxEA12x6RelSessCntrlConfigMode | read-only | mandatory | When the device is in SNMP configuration mode, the value 1 is returned, otherwise 0. If the read value is 0 even though the password was written, the device is… |
| 1.3.6.1.4.1.5040.1.2.51.2.3 | ScalarwtWebio577xxEA12x6RelSessCntrlLogout | read-write | mandatory | If the device is in configuration mode and the session was opened by this SNMP Manager, writing a 1 to this variable will end the session and all parameters ar… |
| 1.3.6.1.4.1.5040.1.2.51.2.4 | ScalarwtWebio577xxEA12x6RelSessCntrlAdminPassword | read-write | mandatory | This password protects access to the variables with administrator rights. It can only be changed by the administrator. If no password was assigned, the valid p… |
| 1.3.6.1.4.1.5040.1.2.51.2.5 | ScalarwtWebio577xxEA12x6RelSessCntrlConfigPassword | read-write | mandatory | This password protects access to the variables with configurator rights. It can be changed by the administrator and by the configurator. If no password was ass… |
| 1.3.6.1.4.1.5040.1.2.51.3 | NodewtWebio577xxEA12x6RelConfig | |||
| 1.3.6.1.4.1.5040.1.2.51.3.1 | NodewtWebio577xxEA12x6RelDevice | |||
| 1.3.6.1.4.1.5040.1.2.51.3.1.1 | NodewtWebio577xxEA12x6RelText | |||
| 1.3.6.1.4.1.5040.1.2.51.3.1.1.1 | ScalarwtWebio577xxEA12x6RelDeviceName | read-write | mandatory | Name of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.1.2 | ScalarwtWebio577xxEA12x6RelDeviceText | read-write | mandatory | Description of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.1.3 | ScalarwtWebio577xxEA12x6RelDeviceLocation | read-write | mandatory | Description of the location of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.1.4 | ScalarwtWebio577xxEA12x6RelDeviceContact | read-write | mandatory | Contact address of the system operator of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.2 | NodewtWebio577xxEA12x6RelTimeDate | |||
| 1.3.6.1.4.1.5040.1.2.51.3.1.2.1 | NodewtWebio577xxEA12x6RelTimeZone | |||
| 1.3.6.1.4.1.5040.1.2.51.3.1.2.1.1 | ScalarwtWebio577xxEA12x6RelTzOffsetHrs | read-write | mandatory | Offset hours for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.2.1.2 | ScalarwtWebio577xxEA12x6RelTzOffsetMin | read-write | mandatory | Offset minutes for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.2.1.3 | ScalarwtWebio577xxEA12x6RelTzEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Timezone |
| 1.3.6.1.4.1.5040.1.2.51.3.1.2.1.4 | ScalarwtWebio577xxEA12x6RelStTzOffsetHrs | read-write | mandatory | Offset hours of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.2.1.5 | ScalarwtWebio577xxEA12x6RelStTzOffsetMin | read-write | mandatory | Offset minutes of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.2.1.6 | ScalarwtWebio577xxEA12x6RelStTzEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Summertime |
| 1.3.6.1.4.1.5040.1.2.51.3.1.2.1.7 | ScalarwtWebio577xxEA12x6RelStTzStartMonth | read-write | mandatory | Month in which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.2.1.8 | ScalarwtWebio577xxEA12x6RelStTzStartMode | read-write | mandatory | Mode of the day of the week for which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.2.1.9 | ScalarwtWebio577xxEA12x6RelStTzStartWday | read-write | mandatory | Day of the week on which the change is made from winter time to summer time |
| 1.3.6.1.4.1.5040.1.2.51.3.1.2.1.10 | ScalarwtWebio577xxEA12x6RelStTzStartHrs | read-write | mandatory | Hour in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.2.1.11 | ScalarwtWebio577xxEA12x6RelStTzStartMin | read-write | mandatory | Minute in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.2.1.12 | ScalarwtWebio577xxEA12x6RelStTzStopMonth | read-write | mandatory | Month in which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.2.1.13 | ScalarwtWebio577xxEA12x6RelStTzStopMode | read-write | mandatory | Mode of the week day on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.2.1.14 | ScalarwtWebio577xxEA12x6RelStTzStopWday | read-write | mandatory | Day of the week on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.2.1.15 | ScalarwtWebio577xxEA12x6RelStTzStopHrs | read-write | mandatory | Hour at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.2.1.16 | ScalarwtWebio577xxEA12x6RelStTzStopMin | read-write | mandatory | Minute at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.2.2 | NodewtWebio577xxEA12x6RelTimeServer | |||
| 1.3.6.1.4.1.5040.1.2.51.3.1.2.2.1 | ScalarwtWebio577xxEA12x6RelTimeServer1 | read-write | mandatory | IP address or name of the 1st time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.51.3.1.2.2.2 | ScalarwtWebio577xxEA12x6RelTimeServer2 | read-write | mandatory | IP address or name of the 2nd time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.51.3.1.2.2.3 | ScalarwtWebio577xxEA12x6RelTsEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Time Server |
| 1.3.6.1.4.1.5040.1.2.51.3.1.2.2.4 | ScalarwtWebio577xxEA12x6RelTsSyncTime | read-write | mandatory | Daily synchronisation time with the time server (hour: 0-23). |
| 1.3.6.1.4.1.5040.1.2.51.3.1.2.3 | NodewtWebio577xxEA12x6RelDeviceClock | |||
| 1.3.6.1.4.1.5040.1.2.51.3.1.2.3.1 | ScalarwtWebio577xxEA12x6RelClockHrs | read-write | mandatory | Clock hours taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.2.3.2 | ScalarwtWebio577xxEA12x6RelClockMin | read-write | mandatory | Clock minutes taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.2.3.3 | ScalarwtWebio577xxEA12x6RelClockDay | read-write | mandatory | Date: Day of the month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.2.3.4 | ScalarwtWebio577xxEA12x6RelClockMonth | read-write | mandatory | Date: Month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.2.3.5 | ScalarwtWebio577xxEA12x6RelClockYear | read-write | mandatory | Date: Year, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3 | NodewtWebio577xxEA12x6RelBasic | |||
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.1 | NodewtWebio577xxEA12x6RelNetwork | |||
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.1.1 | ScalarwtWebio577xxEA12x6RelIpAddress | read-write | mandatory | IP address of the Webio |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.1.2 | ScalarwtWebio577xxEA12x6RelSubnetMask | read-write | mandatory | Subnet mask of the Webio |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.1.3 | ScalarwtWebio577xxEA12x6RelGateway | read-write | mandatory | Gateway of the Webio |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.1.4 | ScalarwtWebio577xxEA12x6RelDnsServer1 | read-write | mandatory | IP address of the 1st DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.1.5 | ScalarwtWebio577xxEA12x6RelDnsServer2 | read-write | mandatory | IP address of the 2nd DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.1.6 | ScalarwtWebio577xxEA12x6RelAddConfig | read-write | mandatory | Additional configuration (1=ON): Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1: DHCP enable Bit 0: BOOTP enable |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.2 | NodewtWebio577xxEA12x6RelHTTP | |||
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.2.1 | ScalarwtWebio577xxEA12x6RelStartup | read-write | mandatory | Binary coded start page, more than one page must not be selected: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 2: user.htm Bit 1: home.htm Bit … |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.2.2 | ScalarwtWebio577xxEA12x6RelGetHeaderEnable | read-write | mandatory | If bits are set, every answer of a short form GET question will be lead by the IP-address and name of the device (Header) or a HTTP header (HTTP): Octet 1: unu… |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.2.3 | ScalarwtWebio577xxEA12x6RelHttpInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.2.4 | ScalarwtWebio577xxEA12x6RelHttpPort | read-write | mandatory | Definition of the standard HTML port (Default: 80). |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.3 | NodewtWebio577xxEA12x6RelMail | |||
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.3.1 | ScalarwtWebio577xxEA12x6RelMailAdName | read-write | mandatory | Device name for mail administration. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.3.2 | ScalarwtWebio577xxEA12x6RelMailReply | read-write | mandatory | Reply address for the mail server. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.3.3 | ScalarwtWebio577xxEA12x6RelMailServer | read-write | mandatory | Name or IP address of the mail server. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.3.4 | ScalarwtWebio577xxEA12x6RelMailEnable | read-write | mandatory | Set this bit to enable the sending of mails: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Mail enable |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.3.5 | ScalarwtWebio577xxEA12x6RelMailAuthentication | read-write | mandatory | Selection of the authentication modi: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTE… |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.3.6 | ScalarwtWebio577xxEA12x6RelMailAuthUser | read-write | mandatory | Name of the user to be authenticated. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.3.7 | ScalarwtWebio577xxEA12x6RelMailAuthPassword | read-write | mandatory | Authentication password. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.3.8 | ScalarwtWebio577xxEA12x6RelMailPop3Server | read-write | mandatory | Name or Ip-address of the POP3 Servers. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.4 | NodewtWebio577xxEA12x6RelSNMP | |||
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.4.1 | ScalarwtWebio577xxEA12x6RelSnmpEnable | read-write | mandatory | Set bit 0 to enable SNMP. If disabled, the device did not respond to any SNMP requests. Bit 1 decided wether the community string of read operations is compare… |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.4.2 | ScalarwtWebio577xxEA12x6RelSnmpCommunityStringRead | read-write | mandatory | Community string read only |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.4.3 | ScalarwtWebio577xxEA12x6RelSnmpCommunityStringReadWrite | read-write | mandatory | Community string read / write |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.4.4 | ScalarwtWebio577xxEA12x6RelSnmpSystemTrapManagerIP | read-write | mandatory | Name or IP address of the TCP server which accepts the system trap. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.4.5 | ScalarwtWebio577xxEA12x6RelSnmpSystemTrapEnable | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2: Diag messages Bit 3-7: unused |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.4.6 | ScalarwtWebio577xxEA12x6RelSnmpSystemTrapManagerPort | read-write | mandatory | Port number of the TCP server which accepts the system trap. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.5 | NodewtWebio577xxEA12x6RelUDP | |||
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.5.1 | ScalarwtWebio577xxEA12x6RelUdpAdminPort | read-write | mandatory | Udp port to which the Udp queries ( short form GET requests) can be sent. This port number must be unique within the device. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.5.2 | ScalarwtWebio577xxEA12x6RelUdpEnable | read-write | mandatory | Set this bit to enable UDP support: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : UDP enable |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.5.3 | ScalarwtWebio577xxEA12x6RelUdpRemotePort | read-write | mandatory | Udp remote port setting. If this value is set to zero, the source port read from a request will be used as destination port for the answer. A non zero value fo… |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.6 | NodewtWebio577xxEA12x6RelBinary | |||
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.6.1 | ScalarwtWebio577xxEA12x6RelBinaryModeCount | read-only | mandatory | Number of independent binary channels. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.6.2 | TablewtWebio577xxEA12x6RelBinaryIfTable | not-accessible | mandatory | Table of indices. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.6.2.1 | RowwtWebio577xxEA12x6RelBinaryIfEntry | not-accessible | mandatory | Indices of the binary channels. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.6.2.1.1 | ColumnwtWebio577xxEA12x6RelBinaryModeNo | read-only | mandatory | Number of the binary channel. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.6.3 | TablewtWebio577xxEA12x6RelBinaryTable | not-accessible | mandatory | Table of properties of the binary mode. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.6.3.1 | RowwtWebio577xxEA12x6RelBinaryEntry | not-accessible | mandatory | Binary properties. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.6.3.1.1 | ColumnwtWebio577xxEA12x6RelBinaryOperationMode | read-write | mandatory | Selection of the operation mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: … |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.6.3.1.2 | ColumnwtWebio577xxEA12x6RelBinaryTcpServerLocalPort | read-write | mandatory | Local TCP port for data exchange in this server mode. This port number must be unique within the device. Reserved port number must not be used (refere to the m… |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.6.3.1.3 | ColumnwtWebio577xxEA12x6RelBinaryTcpServerInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.6.3.1.4 | ColumnwtWebio577xxEA12x6RelBinaryTcpServerApplicationMode | read-write | mandatory | Selection of the application mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4… |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.6.3.1.5 | ColumnwtWebio577xxEA12x6RelBinaryTcpClientLocalPort | read-write | mandatory | Local TCP port for data exchange in this client mode. This port number must be unique within the device. Reserved port number must not be used (refere to the m… |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.6.3.1.6 | ColumnwtWebio577xxEA12x6RelBinaryTcpClientServerPort | read-write | mandatory | Port number of the server. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when setting t… |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.6.3.1.7 | ColumnwtWebio577xxEA12x6RelBinaryTcpClientServerIpAddr | read-write | mandatory | Ip address of the server. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when setting th… |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.6.3.1.8 | ColumnwtWebio577xxEA12x6RelBinaryTcpClientServerPassword | read-write | mandatory | Building a connection may be protected by the administrator password of the server. Enter the server password to establish the connection, if a server administ… |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.6.3.1.9 | ColumnwtWebio577xxEA12x6RelBinaryTcpClientInactivity | read-write | mandatory | Connection timeout in 100ms. If no data are exchanged within the specified time, the device closes the connection to the server. The value 0 deactivates the ti… |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.6.3.1.10 | ColumnwtWebio577xxEA12x6RelBinaryTcpClientInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.6.3.1.11 | ColumnwtWebio577xxEA12x6RelBinaryTcpClientInterval | read-write | mandatory | Configurable interval with a 100ms base, in which the Webio device sends data to the configured application. A interval of zero stopps the periodical sending. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.6.3.1.12 | ColumnwtWebio577xxEA12x6RelBinaryTcpClientApplicationMode | read-write | mandatory | Selection of the application mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4… |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.6.3.1.13 | ColumnwtWebio577xxEA12x6RelBinaryUdpPeerLocalPort | read-write | mandatory | Local UDP port for data exchange in this peer to peer mode. This port number must be unique within the device. Reserved port number must not be used (refere to… |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.6.3.1.14 | ColumnwtWebio577xxEA12x6RelBinaryUdpPeerRemotePort | read-write | mandatory | Port number of the remote device. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when se… |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.6.3.1.15 | ColumnwtWebio577xxEA12x6RelBinaryUdpPeerRemoteIpAddr | read-write | mandatory | Ip address of the remote device. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when set… |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.6.3.1.16 | ColumnwtWebio577xxEA12x6RelBinaryUdpPeerInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.6.3.1.17 | ColumnwtWebio577xxEA12x6RelBinaryUdpPeerInterval | read-write | mandatory | Configurable interval with a 100ms base, in which the Webio device sends data to the configured remote device. A interval of zero stopps the periodical sending. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.6.3.1.18 | ColumnwtWebio577xxEA12x6RelBinaryUdpPeerApplicationMode | read-write | mandatory | Selection of the application mode: The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds to the LSB. OCTET 1: unus… |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.6.3.1.19 | ColumnwtWebio577xxEA12x6RelBinaryConnectedPort | read-only | mandatory | Port number of the remote device, after connection has been established. In case of no connection or missing port informations a zero will be read. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.6.3.1.20 | ColumnwtWebio577xxEA12x6RelBinaryConnectedIpAddr | read-only | mandatory | IP address of the remote device, after connection has been established. In case of no connection or missing port informations 0.0.0.0 will be read. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.6.3.1.21 | ColumnwtWebio577xxEA12x6RelBinaryTcpServerClientHttpPort | read-write | mandatory | HTTP port number of the remote device at TCP Server Mode. If an mailfunction occurs status informations will be send to this port. Not used at mode Compatible … |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.6.3.1.22 | ColumnwtWebio577xxEA12x6RelBinaryTcpClientServerHttpPort | read-write | mandatory | HTTP port number of the remote device at TCP Client Mode. In the operating mode Box2Box connection status informations will be exchanged through this port. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.6.3.1.23 | ColumnwtWebio577xxEA12x6RelBinaryTcpClientServerUserName | read-only | mandatory | User Name to login at the remote server, if authentication needed. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.7 | NodewtWebio577xxEA12x6RelSyslog | |||
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.7.1 | ScalarwtWebio577xxEA12x6RelSyslogServerIP | read-write | mandatory | Name or IP address of the Syslog server, which accepts the Syslog messgaes. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.7.2 | ScalarwtWebio577xxEA12x6RelSyslogServerPort | read-write | mandatory | Portnumber of the Syslog servers, default 514. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.7.3 | ScalarwtWebio577xxEA12x6RelSyslogSystemMessagesEnable | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2: Diag Messages Bit 3-7: unused |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.7.4 | ScalarwtWebio577xxEA12x6RelSyslogEnable | read-write | mandatory | Set bit 0to enable Syslog: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Syslog enable |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.8 | NodewtWebio577xxEA12x6RelFTP | |||
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.8.1 | ScalarwtWebio577xxEA12x6RelFTPServerIP | read-write | mandatory | Name or IP address of the FTP server, which accepts the FTP messages. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.8.2 | ScalarwtWebio577xxEA12x6RelFTPServerControlPort | read-write | mandatory | Portnumber of the control port of the FTP server, default 21. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.8.3 | ScalarwtWebio577xxEA12x6RelFTPUserName | read-write | mandatory | FTP Loggin: user name. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.8.4 | ScalarwtWebio577xxEA12x6RelFTPPassword | read-write | mandatory | FTP Loggin: user password. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.8.5 | ScalarwtWebio577xxEA12x6RelFTPAccount | read-write | mandatory | FTP Loggin: name of account. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.8.6 | ScalarwtWebio577xxEA12x6RelFTPOption | read-write | mandatory | Bit 0 switches the FTP Server in Passiv-Mode, the Client controls the data connection on its own: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit … |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.8.7 | ScalarwtWebio577xxEA12x6RelFTPEnable | read-write | mandatory | Set Bit 0 to enable FTP: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : FTP enable |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.12 | NodewtWebio577xxEA12x6RelMQTT | |||
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.12.1 | ScalarwtWebio577xxEA12x6RelMQTTEnable | read-write | mandatory | Bit 7 enables MQTT: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0-6: unused Bit 7 : MQTT enable |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.12.2 | ScalarwtWebio577xxEA12x6RelMQTTBrockerIP | read-write | mandatory | Name or IP-address of the MQTT-Server. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.12.3 | ScalarwtWebio577xxEA12x6RelMQTTUserName | read-write | mandatory | MQTT login user name. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.12.4 | ScalarwtWebio577xxEA12x6RelMQTTPassword | read-write | mandatory | MQTT login password. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.12.5 | ScalarwtWebio577xxEA12x6RelMQTTLocalPort | read-write | mandatory | Local port number. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.12.6 | ScalarwtWebio577xxEA12x6RelMQTTBrokerServerPort | read-write | mandatory | MQTT Server port number. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.12.7 | ScalarwtWebio577xxEA12x6RelMQTTInterval | read-write | mandatory | Ping intervall, if no data has to be send: time in seconds. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.12.8 | ScalarwtWebio577xxEA12x6RelMQTTLastWillEnable | read-write | mandatory | Bit 0 activate MQTT LastWill message: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : MQTT Last will enable |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.12.9 | ScalarwtWebio577xxEA12x6RelMQTTLastWillTopic | read-write | mandatory | MQTT Last Will Topic. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.12.10 | ScalarwtWebio577xxEA12x6RelMQTTLastWillMsg | read-write | mandatory | MQTT Last Will message. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.12.11 | ScalarwtWebio577xxEA12x6RelMQTTLastWillQoS | read-write | mandatory | Binary coded MQTT Publish QoS: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: QoS 0 Bit 1: QoS 1 Bit 2: QoS 2 Bit 3-7:unused |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.12.12 | ScalarwtWebio577xxEA12x6RelMQTTLastWillRetain | read-write | mandatory | Binary coded MQTT Publish Retain properties: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0 : retain enable Bit 1-7 : unused |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.12.13 | ScalarwtWebio577xxEA12x6RelMQTTLastWillConnectEnable | read-write | mandatory | Bit 0 activate MQTT LastWill Connect message: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : MQTT Last will connect message e… |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.12.14 | ScalarwtWebio577xxEA12x6RelMQTTLastWillConnectMsg | read-write | mandatory | MQTT Last Will Connect message will be send with the QoS and Retain settings of the LastWill message. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.13 | NodewtWebio577xxEA12x6RelREST | |||
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.13.1 | ScalarwtWebio577xxEA12x6RelRESTEnable | read-write | mandatory | Bit 0 activates REST: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : REST enable |
| 1.3.6.1.4.1.5040.1.2.51.3.1.3.13.2 | ScalarwtWebio577xxEA12x6RelRESTDigestAuthEnable | read-write | mandatory | Bit 0 activates Digest-Authentification: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Digest Auth enable |
| 1.3.6.1.4.1.5040.1.2.51.3.1.4 | NodewtWebio577xxEA12x6RelOutputMode | |||
| 1.3.6.1.4.1.5040.1.2.51.3.1.4.1 | TablewtWebio577xxEA12x6RelOutputModeTable | not-accessible | mandatory | Table of output mode configurations dependent on the output indices. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.4.1.1 | RowwtWebio577xxEA12x6RelOutputModeEntry | not-accessible | mandatory | Output mode configurations of the individual outputs. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.4.1.1.1 | ColumnwtWebio577xxEA12x6RelOutputModeBit | read-write | mandatory | This binary coded output mode defines the individual operation mode for any output. More than one mode must not be selected. The OCTETS are interpreted bit-by-… |
| 1.3.6.1.4.1.5040.1.2.51.3.1.4.2 | ScalarwtWebio577xxEA12x6RelSafetyTimeout | read-write | mandatory | After this period of time (multiple of 100ms) without receiving data outputs switch to their Safety States. For each output a independend safety state could be… |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5 | NodewtWebio577xxEA12x6RelAlarm | |||
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.1 | ScalarwtWebio577xxEA12x6RelAlarmCount | read-only | mandatory | Number of independent alarms. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.2 | TablewtWebio577xxEA12x6RelAlarmIfTable | not-accessible | mandatory | List of alarm indices. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.2.1 | RowwtWebio577xxEA12x6RelAlarmIfEntry | not-accessible | mandatory | Numbers of the alarms. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.2.1.1 | ColumnwtWebio577xxEA12x6RelAlarmNo | read-only | mandatory | Numbers of the alarms. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3 | TablewtWebio577xxEA12x6RelAlarmTable | not-accessible | mandatory | List of settings depending on the alarm number. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1 | RowwtWebio577xxEA12x6RelAlarmEntry | not-accessible | mandatory | Alarm parameters of the individual alarms. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.1 | ColumnwtWebio577xxEA12x6RelAlarmInputTrigger | read-write | mandatory | This variable allows setting of individual input trigger conditions. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an input. Bit 0 corr… |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.2 | ColumnwtWebio577xxEA12x6RelAlarmOutputTrigger | read-write | mandatory | This variable allows setting of individual output trigger conditions. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 co… |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.3 | ColumnwtWebio577xxEA12x6RelAlarmSystemTrigger | read-write | mandatory | Binary coded trigger conditions: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, … |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.4 | ColumnwtWebio577xxEA12x6RelAlarmMaxCounterValue | read-write | mandatory | This variable configures a max. counter value. If an input counter value exceeds this max. value, the corresponding alarm is triggered. Input counters with its… |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.5 | ColumnwtWebio577xxEA12x6RelAlarmInterval | read-write | mandatory | Send interval for alarm messages. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.6 | ColumnwtWebio577xxEA12x6RelAlarmEnable | read-write | mandatory | Binary coded alarm enable: Octet 1: unused Octet 2: unused Bit 0: UDP enable Bit1-7: unused Octet 4: Bit 0: Mail Enable Bit 1: SNMP Trap enable Bit 2: TCP Clie… |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.7 | ColumnwtWebio577xxEA12x6RelAlarmMailAddr | read-write | mandatory | E-Mail address for sending the alarm mail to. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.8 | ColumnwtWebio577xxEA12x6RelAlarmMailSubject | read-write | mandatory | Subject line for alarm mail. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.9 | ColumnwtWebio577xxEA12x6RelAlarmMailText | read-write | mandatory | Alarm mail text: States of the Webio device can be included by using special tags. Please refer to the respective Webio manual |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.10 | ColumnwtWebio577xxEA12x6RelAlarmSnmpManagerIP | read-write | mandatory | IP address of the SNMP Manager to which the Webio device should send SNMP traps. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.11 | ColumnwtWebio577xxEA12x6RelAlarmSnmpTrapText | read-write | mandatory | This text appears in the trap body. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.12 | ColumnwtWebio577xxEA12x6RelAlarmUdpIpAddr | read-write | mandatory | IP address of the UDP listener to which the Webio device should send UDP traps. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.13 | ColumnwtWebio577xxEA12x6RelAlarmUdpPort | read-write | mandatory | Port number of the UDP listener to which the Webio device should send UDP traps. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.14 | ColumnwtWebio577xxEA12x6RelAlarmUdpText | read-write | mandatory | This text appears in the UDP trap body. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.15 | ColumnwtWebio577xxEA12x6RelAlarmTcpIpAddr | read-write | mandatory | IP address of the TCP listener to which the Webio device should send TCP traps. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.16 | ColumnwtWebio577xxEA12x6RelAlarmTcpPort | read-write | mandatory | Port number of the TCP listener to which the Webio device should send TCP traps. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.17 | ColumnwtWebio577xxEA12x6RelAlarmTcpText | read-write | mandatory | This text appears in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.18 | ColumnwtWebio577xxEA12x6RelAlarmSyslogIpAddr | read-write | mandatory | IP address of the syslog server to which the Webio device should send syslog messages. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.19 | ColumnwtWebio577xxEA12x6RelAlarmSyslogPort | read-write | mandatory | Port number of the syslog server to which the Webio device should send syslog messages. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.20 | ColumnwtWebio577xxEA12x6RelAlarmSyslogText | read-write | mandatory | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.21 | ColumnwtWebio577xxEA12x6RelAlarmFtpDataPort | read-write | mandatory | Local data port: 1..65535 or AUTO: the next free port will be assigned. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.22 | ColumnwtWebio577xxEA12x6RelAlarmFtpFileName | read-write | mandatory | Name of the file including path informations. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.23 | ColumnwtWebio577xxEA12x6RelAlarmFtpText | read-write | mandatory | Message text to store on the FTP server. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.24 | ColumnwtWebio577xxEA12x6RelAlarmFtpOption | read-write | mandatory | Binary coded options, select only one option at the same time: STORE = replace file APPEND = append message at the end of the file Octet 1: unused Octet 2: unu… |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.25 | ColumnwtWebio577xxEA12x6RelAlarmTimerCron | read-write | mandatory | This entry contains 5 space or tab seperated text fields for time trigger definition. Each field must match with the actual time to trigger a message, weekday … |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.26 | ColumnwtWebio577xxEA12x6RelAlarmMailReleaseSubject | read-write | mandatory | Subject line for alarm mail. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.27 | ColumnwtWebio577xxEA12x6RelAlarmMailReleaseText | read-write | mandatory | Release Alarm mail text: States of the Webio device can be included by using special tags. Please refer to the respective Webio manual |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.28 | ColumnwtWebio577xxEA12x6RelAlarmSnmpTrapReleaseText | read-write | mandatory | This text appears in the trap body. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.29 | ColumnwtWebio577xxEA12x6RelAlarmUdpReleaseText | read-write | mandatory | This text appears in the UDP trap body. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.30 | ColumnwtWebio577xxEA12x6RelAlarmTcpReleaseText | read-write | mandatory | This text appears in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.31 | ColumnwtWebio577xxEA12x6RelAlarmSyslogReleaseText | read-write | mandatory | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.32 | ColumnwtWebio577xxEA12x6RelAlarmFtpReleaseText | read-write | mandatory | Message text to store on the FTP server. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.34 | ColumnwtWebio577xxEA12x6RelAlarmGlobalEnable | read-write | mandatory | Binary coded alarm activation: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bi… |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.58 | ColumnwtWebio577xxEA12x6RelAlarmCombinationLogic | read-write | mandatory | Binary coded logic, all Input/Output-trigger will be combined: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: un… |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.59 | ColumnwtWebio577xxEA12x6RelAlarmTrgMqttTopic | read-write | mandatory | MQTT subscribe topic. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.60 | ColumnwtWebio577xxEA12x6RelAlarmTrgMqttTopicText | read-write | mandatory | Receiving this text from the MQTT Broker, Alarm will be triggered. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.61 | ColumnwtWebio577xxEA12x6RelAlarmHttpReqAuthEnable | read-write | mandatory | Binary coded value: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bit 1-7: unus… |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.62 | ColumnwtWebio577xxEA12x6RelAlarmHttpReqAuthUser | read-write | mandatory | HTTP Request: User |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.63 | ColumnwtWebio577xxEA12x6RelAlarmHttpReqAuthPassword | read-write | mandatory | HTTP Request: Password |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.64 | ColumnwtWebio577xxEA12x6RelAlarmHttpReqSetUrl | read-write | mandatory | HTTP Request: Set URL |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.65 | ColumnwtWebio577xxEA12x6RelAlarmHttpReqClearUrl | read-write | mandatory | HTTP Request: Clear URL |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.66 | ColumnwtWebio577xxEA12x6RelAlarmHttpReqServerPort | read-write | mandatory | HTTP Request: Server Port |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.67 | ColumnwtWebio577xxEA12x6RelAlarmMqttTopicPath | read-write | mandatory | MQTT Publish: Topic path |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.68 | ColumnwtWebio577xxEA12x6RelAlarmMqttTopicSetTopic | read-write | mandatory | MQTT Publish: Topic SET message |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.69 | ColumnwtWebio577xxEA12x6RelAlarmMqttTopicClear | read-write | mandatory | MQTT Publish: Topic CLEAR message |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.70 | ColumnwtWebio577xxEA12x6RelAlarmSetOutputsOwn | read-write | mandatory | This variable allows setting of individual output. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds to the LS… |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.71 | ColumnwtWebio577xxEA12x6RelAlarmSetOutputsServerIp | read-write | mandatory | Set Outputs: Server IP Address |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.72 | ColumnwtWebio577xxEA12x6RelAlarmSetOutputsServerPort | read-write | mandatory | Set Outputs: Server Port |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.73 | ColumnwtWebio577xxEA12x6RelAlarmSetOutputsServerPassword | read-write | mandatory | Set Outputs: Server Pasword |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.74 | ColumnwtWebio577xxEA12x6RelAlarmSetOutputsServerOutputs | read-write | mandatory | This variable allows setting of individual output. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds to the LS… |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.75 | ColumnwtWebio577xxEA12x6RelAlarmSetOutputsDest | read-write | mandatory | Binary coded value: Bit 0 = LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bit 2-7: unused Bit 1 : set outputs of remote server. Bit 0 : set out… |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.76 | ColumnwtWebio577xxEA12x6RelAlarmSnmpManagerPort | read-write | mandatory | Port number of the SNMP Manager to which the Webio device should send SNMP traps. |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.77 | ColumnwtWebio577xxEA12x6RelAlarmMqttQoS | read-write | mandatory | Binary coded value: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: QoS 0 Bit 1: QoS 1 Bit 2: QoS 2 Bit 3-7:unused |
| 1.3.6.1.4.1.5040.1.2.51.3.1.5.3.1.78 | ColumnwtWebio577xxEA12x6RelAlarmMqttRetain | read-write | mandatory | Binary coded value: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0 : retain enable Bit 1-7 : unused |
| 1.3.6.1.4.1.5040.1.2.51.3.2 | NodewtWebio577xxEA12x6RelPorts | |||
| 1.3.6.1.4.1.5040.1.2.51.3.2.1 | TablewtWebio577xxEA12x6RelInputPortTable | not-accessible | mandatory | List of settings depending on the input number. |
| 1.3.6.1.4.1.5040.1.2.51.3.2.1.1 | RowwtWebio577xxEA12x6RelInputPortEntry | not-accessible | mandatory | Input parameter for the individual inputs. |
| 1.3.6.1.4.1.5040.1.2.51.3.2.1.1.1 | ColumnwtWebio577xxEA12x6RelPortInputName | read-write | mandatory | Name of the input. |
| 1.3.6.1.4.1.5040.1.2.51.3.2.1.1.2 | ColumnwtWebio577xxEA12x6RelPortInputText | read-write | mandatory | Description of the input. |
| 1.3.6.1.4.1.5040.1.2.51.3.2.1.1.3 | ColumnwtWebio577xxEA12x6RelPortInputMode | read-write | mandatory | Binary coded modes: Selecting short pulse detection enable by setting the corresponding bit to 1 enables interrupt support for counting. Only positive edges ar… |
| 1.3.6.1.4.1.5040.1.2.51.3.2.1.1.4 | ColumnwtWebio577xxEA12x6RelPortInputFilter | read-write | mandatory | Pulses with a duration shorter than here specified (duration in 1/1000 sec), are ignored. |
| 1.3.6.1.4.1.5040.1.2.51.3.2.1.1.5 | ColumnwtWebio577xxEA12x6RelPortInputBicountPulsePolarity | read-write | mandatory | This value defines the polarity of the input pulse. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 0 : negative polarity Bit 1 : positive polarit… |
| 1.3.6.1.4.1.5040.1.2.51.3.2.1.1.6 | ColumnwtWebio577xxEA12x6RelPortInputBicountInactivTimeout | read-write | mandatory | Pulse chains with a duration shorter than here specified (in 1/10 sek), are ignored. |
| 1.3.6.1.4.1.5040.1.2.51.3.2.2 | TablewtWebio577xxEA12x6RelOutputPortTable | not-accessible | mandatory | List of settings depending on the output number. |
| 1.3.6.1.4.1.5040.1.2.51.3.2.2.1 | RowwtWebio577xxEA12x6RelOutputPortEntry | not-accessible | mandatory | Output parameters of the individual outputs. |
| 1.3.6.1.4.1.5040.1.2.51.3.2.2.1.1 | ColumnwtWebio577xxEA12x6RelPortOutputName | read-write | mandatory | Name of the output. |
| 1.3.6.1.4.1.5040.1.2.51.3.2.2.1.2 | ColumnwtWebio577xxEA12x6RelPortOutputText | read-write | mandatory | Description of the output. |
| 1.3.6.1.4.1.5040.1.2.51.3.2.2.1.3 | ColumnwtWebio577xxEA12x6RelPortOutputGroupMode | read-write | mandatory | No function within this device. |
| 1.3.6.1.4.1.5040.1.2.51.3.2.2.1.4 | ColumnwtWebio577xxEA12x6RelPortOutputSafetyState | read-write | mandatory | This variable allows setting of individual digital outputs. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds … |
| 1.3.6.1.4.1.5040.1.2.51.3.2.2.1.9 | ColumnwtWebio577xxEA12x6RelPortPulseDuration | read-write | mandatory | Pulse length in 1/1000 sec. Setting this value to zero, disables the pulse output. |
| 1.3.6.1.4.1.5040.1.2.51.3.2.2.1.10 | ColumnwtWebio577xxEA12x6RelPortPulsePolarity | read-write | mandatory | This value defines the polarity of the output pulse, if wtWebio577xxEA12x6RelPortPulseDuration is not set to zero. After the pulse is finished, the output swit… |
| 1.3.6.1.4.1.5040.1.2.51.3.3 | NodewtWebio577xxEA12x6RelManufact | |||
| 1.3.6.1.4.1.5040.1.2.51.3.3.1 | ScalarwtWebio577xxEA12x6RelMfName | read-write | mandatory | Manufacturer company name |
| 1.3.6.1.4.1.5040.1.2.51.3.3.2 | ScalarwtWebio577xxEA12x6RelMfAddr | read-write | mandatory | Manufacturer address. |
| 1.3.6.1.4.1.5040.1.2.51.3.3.3 | ScalarwtWebio577xxEA12x6RelMfHotline | read-write | mandatory | Manufacturer hotline. |
| 1.3.6.1.4.1.5040.1.2.51.3.3.4 | ScalarwtWebio577xxEA12x6RelMfInternet | read-write | mandatory | Manufacturer Internet address. |
| 1.3.6.1.4.1.5040.1.2.51.3.3.5 | ScalarwtWebio577xxEA12x6RelMfDeviceTyp | read-write | mandatory | Manufacturer device name (model number). |
| 1.3.6.1.4.1.5040.1.2.51.4 | NodewtWebio577xxEA12x6RelDiag | |||
| 1.3.6.1.4.1.5040.1.2.51.4.1 | ScalarwtWebio577xxEA12x6RelDiagErrorCount | read-only | mandatory | Number of entries in the error memory. |
| 1.3.6.1.4.1.5040.1.2.51.4.2 | ScalarwtWebio577xxEA12x6RelDiagBinaryError | read-only | mandatory | Error causes coded bit-by-bit. |
| 1.3.6.1.4.1.5040.1.2.51.4.3 | ScalarwtWebio577xxEA12x6RelDiagErrorIndex | read-write | mandatory | The value of this variable is used as an index to read an error massege from wtWebio577xxEA12x6RelDiagErrorMessage. Errors are numbered from 1 to wtWebio577xxE… |
| 1.3.6.1.4.1.5040.1.2.51.4.4 | ScalarwtWebio577xxEA12x6RelDiagErrorMessage | read-only | mandatory | Using wtWebio577xxEA12x6RelDiagErrorIndex as an index, the appropriate message is available. |
| 1.3.6.1.4.1.5040.1.2.51.4.5 | ScalarwtWebio577xxEA12x6RelDiagErrorClear | write-only | mandatory | Writing 1 into this variable clears all diagnosis messages. |
| 1.3.6.1.4.1.5040.1.2.51.41 | NodewtWebio577xxEA12x6RelAlert1 | This SNMP trap is generated when Alarm 1 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.51.42 | NodewtWebio577xxEA12x6RelAlert2 | This SNMP trap is generated when Alarm 2 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.51.43 | NodewtWebio577xxEA12x6RelAlert3 | This SNMP trap is generated when Alarm 3 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.51.44 | NodewtWebio577xxEA12x6RelAlert4 | This SNMP trap is generated when Alarm 4 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.51.45 | NodewtWebio577xxEA12x6RelAlert5 | This SNMP trap is generated when Alarm 5 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.51.46 | NodewtWebio577xxEA12x6RelAlert6 | This SNMP trap is generated when Alarm 6 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.51.47 | NodewtWebio577xxEA12x6RelAlert7 | This SNMP trap is generated when Alarm 7 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.51.48 | NodewtWebio577xxEA12x6RelAlert8 | This SNMP trap is generated when Alarm 8 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.51.49 | NodewtWebio577xxEA12x6RelAlert9 | This SNMP trap is generated when Alarm 9 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.51.50 | NodewtWebio577xxEA12x6RelAlert10 | This SNMP trap is generated when Alarm 10 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.51.51 | NodewtWebio577xxEA12x6RelAlert11 | This SNMP trap is generated when Alarm 11 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.51.52 | NodewtWebio577xxEA12x6RelAlert12 | This SNMP trap is generated when Alarm 12 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.51.71 | NodewtWebio577xxEA12x6RelAlert13 | This SNMP trap is generated when Alarm 1 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.51.72 | NodewtWebio577xxEA12x6RelAlert14 | This SNMP trap is generated when Alarm 2 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.51.73 | NodewtWebio577xxEA12x6RelAlert15 | This SNMP trap is generated when Alarm 3 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.51.74 | NodewtWebio577xxEA12x6RelAlert16 | This SNMP trap is generated when Alarm 4 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.51.75 | NodewtWebio577xxEA12x6RelAlert17 | This SNMP trap is generated when Alarm 5 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.51.76 | NodewtWebio577xxEA12x6RelAlert18 | This SNMP trap is generated when Alarm 6 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.51.77 | NodewtWebio577xxEA12x6RelAlert19 | This SNMP trap is generated when Alarm 7 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.51.78 | NodewtWebio577xxEA12x6RelAlert20 | This SNMP trap is generated when Alarm 8 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.51.79 | NodewtWebio577xxEA12x6RelAlert21 | This SNMP trap is generated when Alarm 9 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.51.80 | NodewtWebio577xxEA12x6RelAlert22 | This SNMP trap is generated when Alarm 10 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.51.81 | NodewtWebio577xxEA12x6RelAlert23 | This SNMP trap is generated when Alarm 11 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.51.82 | NodewtWebio577xxEA12x6RelAlert24 | This SNMP trap is generated when Alarm 12 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.51.110 | NodewtWebio577xxEA12x6RelAlertDiag | This SNMP trap is generated when a diagnosis/error message was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.52 | NodewtWebio577xxEA2x2 | |||
| 1.3.6.1.4.1.5040.1.2.52.1 | NodewtWebio577xxEA2x2InOut | |||
| 1.3.6.1.4.1.5040.1.2.52.1.1 | ScalarwtWebio577xxEA2x2Inputs | read-only | mandatory | Number of idependent inputs. |
| 1.3.6.1.4.1.5040.1.2.52.1.2 | ScalarwtWebio577xxEA2x2Outputs | read-only | mandatory | Number of idependent outputs. |
| 1.3.6.1.4.1.5040.1.2.52.1.3 | TablewtWebio577xxEA2x2InputTable | not-accessible | mandatory | List of input indices. |
| 1.3.6.1.4.1.5040.1.2.52.1.3.1 | RowwtWebio577xxEA2x2InputEntry | not-accessible | mandatory | Number of the inputs. |
| 1.3.6.1.4.1.5040.1.2.52.1.3.1.1 | ColumnwtWebio577xxEA2x2InputNo | read-only | mandatory | Index numbers of the inputs. |
| 1.3.6.1.4.1.5040.1.2.52.1.3.1.2 | ColumnwtWebio577xxEA2x2InputCounter | read-only | mandatory | Value of the input counter. |
| 1.3.6.1.4.1.5040.1.2.52.1.3.1.3 | ColumnwtWebio577xxEA2x2InputCounterClear | read-only | mandatory | Clears the input counter after returning its value. |
| 1.3.6.1.4.1.5040.1.2.52.1.3.1.4 | ColumnwtWebio577xxEA2x2InputState | read-only | mandatory | Value of a single input bit, 0-OFF, 1-ON. |
| 1.3.6.1.4.1.5040.1.2.52.1.4 | ScalarwtWebio577xxEA2x2InputValue | read-only | mandatory | This variable is used to read the inputs of the digital I/O port. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corres… |
| 1.3.6.1.4.1.5040.1.2.52.1.5 | TablewtWebio577xxEA2x2OutputTable | not-accessible | mandatory | List of output indices. |
| 1.3.6.1.4.1.5040.1.2.52.1.5.1 | RowwtWebio577xxEA2x2OutputEntry | not-accessible | mandatory | Number of the outputs. |
| 1.3.6.1.4.1.5040.1.2.52.1.5.1.1 | ColumnwtWebio577xxEA2x2OutputNo | read-only | mandatory | Output number. |
| 1.3.6.1.4.1.5040.1.2.52.1.5.1.2 | ColumnwtWebio577xxEA2x2OutputState | read-write | mandatory | Value of a single output bit, 0-OFF, 1-ON. |
| 1.3.6.1.4.1.5040.1.2.52.1.6 | ScalarwtWebio577xxEA2x2OutputValue | read-write | mandatory | This variable is used to read and write the outputs of the digital I/O port. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. B… |
| 1.3.6.1.4.1.5040.1.2.52.1.7 | ScalarwtWebio577xxEA2x2SetOutput | read-write | mandatory | This variable allows setting of individual digital outputs. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds … |
| 1.3.6.1.4.1.5040.1.2.52.2 | NodewtWebio577xxEA2x2SessCntrl | |||
| 1.3.6.1.4.1.5040.1.2.52.2.1 | ScalarwtWebio577xxEA2x2SessCntrlPassword | read-write | mandatory | Entering this password opens a session which is ended by writing a 1 to wtWebio577xxEA2x2SessCntrlLogout. When read this variable provides a string of length z… |
| 1.3.6.1.4.1.5040.1.2.52.2.2 | ScalarwtWebio577xxEA2x2SessCntrlConfigMode | read-only | mandatory | When the device is in SNMP configuration mode, the value 1 is returned, otherwise 0. If the read value is 0 even though the password was written, the device is… |
| 1.3.6.1.4.1.5040.1.2.52.2.3 | ScalarwtWebio577xxEA2x2SessCntrlLogout | read-write | mandatory | If the device is in configuration mode and the session was opened by this SNMP Manager, writing a 1 to this variable will end the session and all parameters ar… |
| 1.3.6.1.4.1.5040.1.2.52.2.4 | ScalarwtWebio577xxEA2x2SessCntrlAdminPassword | read-write | mandatory | This password protects access to the variables with administrator rights. It can only be changed by the administrator. If no password was assigned, the valid p… |
| 1.3.6.1.4.1.5040.1.2.52.2.5 | ScalarwtWebio577xxEA2x2SessCntrlConfigPassword | read-write | mandatory | This password protects access to the variables with configurator rights. It can be changed by the administrator and by the configurator. If no password was ass… |
| 1.3.6.1.4.1.5040.1.2.52.3 | NodewtWebio577xxEA2x2Config | |||
| 1.3.6.1.4.1.5040.1.2.52.3.1 | NodewtWebio577xxEA2x2Device | |||
| 1.3.6.1.4.1.5040.1.2.52.3.1.1 | NodewtWebio577xxEA2x2Text | |||
| 1.3.6.1.4.1.5040.1.2.52.3.1.1.1 | ScalarwtWebio577xxEA2x2DeviceName | read-write | mandatory | Name of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.1.2 | ScalarwtWebio577xxEA2x2DeviceText | read-write | mandatory | Description of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.1.3 | ScalarwtWebio577xxEA2x2DeviceLocation | read-write | mandatory | Description of the location of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.1.4 | ScalarwtWebio577xxEA2x2DeviceContact | read-write | mandatory | Contact address of the system operator of the Webio, which is user definable. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.2 | NodewtWebio577xxEA2x2TimeDate | |||
| 1.3.6.1.4.1.5040.1.2.52.3.1.2.1 | NodewtWebio577xxEA2x2TimeZone | |||
| 1.3.6.1.4.1.5040.1.2.52.3.1.2.1.1 | ScalarwtWebio577xxEA2x2TzOffsetHrs | read-write | mandatory | Offset hours for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.2.1.2 | ScalarwtWebio577xxEA2x2TzOffsetMin | read-write | mandatory | Offset minutes for the time zone (winter time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.2.1.3 | ScalarwtWebio577xxEA2x2TzEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Timezone |
| 1.3.6.1.4.1.5040.1.2.52.3.1.2.1.4 | ScalarwtWebio577xxEA2x2StTzOffsetHrs | read-write | mandatory | Offset hours of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.2.1.5 | ScalarwtWebio577xxEA2x2StTzOffsetMin | read-write | mandatory | Offset minutes of the time zone (summer time) with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.2.1.6 | ScalarwtWebio577xxEA2x2StTzEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Summertime |
| 1.3.6.1.4.1.5040.1.2.52.3.1.2.1.7 | ScalarwtWebio577xxEA2x2StTzStartMonth | read-write | mandatory | Month in which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.2.1.8 | ScalarwtWebio577xxEA2x2StTzStartMode | read-write | mandatory | Mode of the day of the week for which the change is made from winter time to summer time. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.2.1.9 | ScalarwtWebio577xxEA2x2StTzStartWday | read-write | mandatory | Day of the week on which the change is made from winter time to summer time |
| 1.3.6.1.4.1.5040.1.2.52.3.1.2.1.10 | ScalarwtWebio577xxEA2x2StTzStartHrs | read-write | mandatory | Hour in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.2.1.11 | ScalarwtWebio577xxEA2x2StTzStartMin | read-write | mandatory | Minute in which the time zone is changed from winter to summer time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.2.1.12 | ScalarwtWebio577xxEA2x2StTzStopMonth | read-write | mandatory | Month in which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.2.1.13 | ScalarwtWebio577xxEA2x2StTzStopMode | read-write | mandatory | Mode of the week day on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.2.1.14 | ScalarwtWebio577xxEA2x2StTzStopWday | read-write | mandatory | Day of the week on which the change is made from summer time to winter time. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.2.1.15 | ScalarwtWebio577xxEA2x2StTzStopHrs | read-write | mandatory | Hour at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.2.1.16 | ScalarwtWebio577xxEA2x2StTzStopMin | read-write | mandatory | Minute at which the time zone is changed from summer to winter time with respect to UTC. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.2.2 | NodewtWebio577xxEA2x2TimeServer | |||
| 1.3.6.1.4.1.5040.1.2.52.3.1.2.2.1 | ScalarwtWebio577xxEA2x2TimeServer1 | read-write | mandatory | IP address or name of the 1st time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.52.3.1.2.2.2 | ScalarwtWebio577xxEA2x2TimeServer2 | read-write | mandatory | IP address or name of the 2nd time server in ASCII |
| 1.3.6.1.4.1.5040.1.2.52.3.1.2.2.3 | ScalarwtWebio577xxEA2x2TsEnable | read-write | mandatory | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Time Server |
| 1.3.6.1.4.1.5040.1.2.52.3.1.2.2.4 | ScalarwtWebio577xxEA2x2TsSyncTime | read-write | mandatory | Daily synchronisation time with the time server (hour: 0-23). |
| 1.3.6.1.4.1.5040.1.2.52.3.1.2.3 | NodewtWebio577xxEA2x2DeviceClock | |||
| 1.3.6.1.4.1.5040.1.2.52.3.1.2.3.1 | ScalarwtWebio577xxEA2x2ClockHrs | read-write | mandatory | Clock hours taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.2.3.2 | ScalarwtWebio577xxEA2x2ClockMin | read-write | mandatory | Clock minutes taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.2.3.3 | ScalarwtWebio577xxEA2x2ClockDay | read-write | mandatory | Date: Day of the month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.2.3.4 | ScalarwtWebio577xxEA2x2ClockMonth | read-write | mandatory | Date: Month, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.2.3.5 | ScalarwtWebio577xxEA2x2ClockYear | read-write | mandatory | Date: Year, taking into account the time zone settings. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3 | NodewtWebio577xxEA2x2Basic | |||
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.1 | NodewtWebio577xxEA2x2Network | |||
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.1.1 | ScalarwtWebio577xxEA2x2IpAddress | read-write | mandatory | IP address of the Webio |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.1.2 | ScalarwtWebio577xxEA2x2SubnetMask | read-write | mandatory | Subnet mask of the Webio |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.1.3 | ScalarwtWebio577xxEA2x2Gateway | read-write | mandatory | Gateway of the Webio |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.1.4 | ScalarwtWebio577xxEA2x2DnsServer1 | read-write | mandatory | IP address of the 1st DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.1.5 | ScalarwtWebio577xxEA2x2DnsServer2 | read-write | mandatory | IP address of the 2nd DNS server in ASCII |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.1.6 | ScalarwtWebio577xxEA2x2AddConfig | read-write | mandatory | Additional configuration (1=ON): Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1: DHCP enable Bit 0: BOOTP enable |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.2 | NodewtWebio577xxEA2x2HTTP | |||
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.2.1 | ScalarwtWebio577xxEA2x2Startup | read-write | mandatory | Binary coded start page, more than one page must not be selected: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 2: user.htm Bit 1: home.htm Bit … |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.2.2 | ScalarwtWebio577xxEA2x2GetHeaderEnable | read-write | mandatory | If bits are set, every answer of a short form GET question will be lead by the IP-address and name of the device (Header) or a HTTP header (HTTP): Octet 1: unu… |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.2.3 | ScalarwtWebio577xxEA2x2HttpInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.2.4 | ScalarwtWebio577xxEA2x2HttpPort | read-write | mandatory | Definition of the standard HTML port (Default: 80). |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.3 | NodewtWebio577xxEA2x2Mail | |||
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.3.1 | ScalarwtWebio577xxEA2x2MailAdName | read-write | mandatory | Device name for mail administration. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.3.2 | ScalarwtWebio577xxEA2x2MailReply | read-write | mandatory | Reply address for the mail server. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.3.3 | ScalarwtWebio577xxEA2x2MailServer | read-write | mandatory | Name or IP address of the mail server. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.3.4 | ScalarwtWebio577xxEA2x2MailEnable | read-write | mandatory | Set this bit to enable the sending of mails: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Mail enable |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.3.5 | ScalarwtWebio577xxEA2x2MailAuthentication | read-write | mandatory | Selection of the authentication modi: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTE… |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.3.6 | ScalarwtWebio577xxEA2x2MailAuthUser | read-write | mandatory | Name of the user to be authenticated. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.3.7 | ScalarwtWebio577xxEA2x2MailAuthPassword | read-write | mandatory | Authentication password. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.3.8 | ScalarwtWebio577xxEA2x2MailPop3Server | read-write | mandatory | Name or Ip-address of the POP3 Servers. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.4 | NodewtWebio577xxEA2x2SNMP | |||
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.4.1 | ScalarwtWebio577xxEA2x2SnmpEnable | read-write | mandatory | Set bit 0 to enable SNMP. If disabled, the device did not respond to any SNMP requests. Bit 1 decided wether the community string of read operations is compare… |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.4.2 | ScalarwtWebio577xxEA2x2SnmpCommunityStringRead | read-write | mandatory | Community string read only |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.4.3 | ScalarwtWebio577xxEA2x2SnmpCommunityStringReadWrite | read-write | mandatory | Community string read / write |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.4.4 | ScalarwtWebio577xxEA2x2SnmpSystemTrapManagerIP | read-write | mandatory | Name or IP address of the TCP server which accepts the system trap. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.4.5 | ScalarwtWebio577xxEA2x2SnmpSystemTrapEnable | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2: Diag messages Bit 3-7: unused |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.4.6 | ScalarwtWebio577xxEA2x2SnmpSystemTrapManagerPort | read-write | mandatory | Port number of the TCP server which accepts the system trap. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.5 | NodewtWebio577xxEA2x2UDP | |||
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.5.1 | ScalarwtWebio577xxEA2x2UdpAdminPort | read-write | mandatory | Udp port to which the Udp queries ( short form GET requests) can be sent. This port number must be unique within the device. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.5.2 | ScalarwtWebio577xxEA2x2UdpEnable | read-write | mandatory | Set this bit to enable UDP support: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : UDP enable |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.5.3 | ScalarwtWebio577xxEA2x2UdpRemotePort | read-write | mandatory | Udp remote port setting. If this value is set to zero, the source port read from a request will be used as destination port for the answer. A non zero value fo… |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.6 | NodewtWebio577xxEA2x2Binary | |||
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.6.1 | ScalarwtWebio577xxEA2x2BinaryModeCount | read-only | mandatory | Number of independent binary channels. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.6.2 | TablewtWebio577xxEA2x2BinaryIfTable | not-accessible | mandatory | Table of indices. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.6.2.1 | RowwtWebio577xxEA2x2BinaryIfEntry | not-accessible | mandatory | Indices of the binary channels. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.6.2.1.1 | ColumnwtWebio577xxEA2x2BinaryModeNo | read-only | mandatory | Number of the binary channel. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.6.3 | TablewtWebio577xxEA2x2BinaryTable | not-accessible | mandatory | Table of properties of the binary mode. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.6.3.1 | RowwtWebio577xxEA2x2BinaryEntry | not-accessible | mandatory | Binary properties. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.6.3.1.1 | ColumnwtWebio577xxEA2x2BinaryOperationMode | read-write | mandatory | Selection of the operation mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: … |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.6.3.1.2 | ColumnwtWebio577xxEA2x2BinaryTcpServerLocalPort | read-write | mandatory | Local TCP port for data exchange in this server mode. This port number must be unique within the device. Reserved port number must not be used (refere to the m… |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.6.3.1.3 | ColumnwtWebio577xxEA2x2BinaryTcpServerInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.6.3.1.4 | ColumnwtWebio577xxEA2x2BinaryTcpServerApplicationMode | read-write | mandatory | Selection of the application mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4… |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.6.3.1.5 | ColumnwtWebio577xxEA2x2BinaryTcpClientLocalPort | read-write | mandatory | Local TCP port for data exchange in this client mode. This port number must be unique within the device. Reserved port number must not be used (refere to the m… |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.6.3.1.6 | ColumnwtWebio577xxEA2x2BinaryTcpClientServerPort | read-write | mandatory | Port number of the server. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when setting t… |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.6.3.1.7 | ColumnwtWebio577xxEA2x2BinaryTcpClientServerIpAddr | read-write | mandatory | Ip address of the server. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when setting th… |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.6.3.1.8 | ColumnwtWebio577xxEA2x2BinaryTcpClientServerPassword | read-write | mandatory | Building a connection may be protected by the administrator password of the server. Enter the server password to establish the connection, if a server administ… |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.6.3.1.9 | ColumnwtWebio577xxEA2x2BinaryTcpClientInactivity | read-write | mandatory | Connection timeout in 100ms. If no data are exchanged within the specified time, the device closes the connection to the server. The value 0 deactivates the ti… |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.6.3.1.10 | ColumnwtWebio577xxEA2x2BinaryTcpClientInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.6.3.1.11 | ColumnwtWebio577xxEA2x2BinaryTcpClientInterval | read-write | mandatory | Configurable interval with a 100ms base, in which the Webio device sends data to the configured application. A interval of zero stopps the periodical sending. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.6.3.1.12 | ColumnwtWebio577xxEA2x2BinaryTcpClientApplicationMode | read-write | mandatory | Selection of the application mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4… |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.6.3.1.13 | ColumnwtWebio577xxEA2x2BinaryUdpPeerLocalPort | read-write | mandatory | Local UDP port for data exchange in this peer to peer mode. This port number must be unique within the device. Reserved port number must not be used (refere to… |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.6.3.1.14 | ColumnwtWebio577xxEA2x2BinaryUdpPeerRemotePort | read-write | mandatory | Port number of the remote device. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when se… |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.6.3.1.15 | ColumnwtWebio577xxEA2x2BinaryUdpPeerRemoteIpAddr | read-write | mandatory | Ip address of the remote device. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when set… |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.6.3.1.16 | ColumnwtWebio577xxEA2x2BinaryUdpPeerInputTrigger | read-write | mandatory | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rul… |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.6.3.1.17 | ColumnwtWebio577xxEA2x2BinaryUdpPeerInterval | read-write | mandatory | Configurable interval with a 100ms base, in which the Webio device sends data to the configured remote device. A interval of zero stopps the periodical sending. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.6.3.1.18 | ColumnwtWebio577xxEA2x2BinaryUdpPeerApplicationMode | read-write | mandatory | Selection of the application mode: The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds to the LSB. OCTET 1: unus… |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.6.3.1.19 | ColumnwtWebio577xxEA2x2BinaryConnectedPort | read-only | mandatory | Port number of the remote device, after connection has been established. In case of no connection or missing port informations a zero will be read. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.6.3.1.20 | ColumnwtWebio577xxEA2x2BinaryConnectedIpAddr | read-only | mandatory | IP address of the remote device, after connection has been established. In case of no connection or missing port informations 0.0.0.0 will be read. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.6.3.1.21 | ColumnwtWebio577xxEA2x2BinaryTcpServerClientHttpPort | read-write | mandatory | HTTP port number of the remote device at TCP Server Mode. If an mailfunction occurs status informations will be send to this port. Not used at mode Compatible … |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.6.3.1.22 | ColumnwtWebio577xxEA2x2BinaryTcpClientServerHttpPort | read-write | mandatory | HTTP port number of the remote device at TCP Client Mode. In the operating mode Box2Box connection status informations will be exchanged through this port. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.6.3.1.23 | ColumnwtWebio577xxEA2x2BinaryTcpClientServerUserName | read-only | mandatory | User Name to login at the remote server, if authentication needed. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.7 | NodewtWebio577xxEA2x2Syslog | |||
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.7.1 | ScalarwtWebio577xxEA2x2SyslogServerIP | read-write | mandatory | Name or IP address of the Syslog server, which accepts the Syslog messgaes. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.7.2 | ScalarwtWebio577xxEA2x2SyslogServerPort | read-write | mandatory | Portnumber of the Syslog servers, default 514. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.7.3 | ScalarwtWebio577xxEA2x2SyslogSystemMessagesEnable | read-write | mandatory | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2: Diag Messages Bit 3-7: unused |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.7.4 | ScalarwtWebio577xxEA2x2SyslogEnable | read-write | mandatory | Set bit 0to enable Syslog: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Syslog enable |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.8 | NodewtWebio577xxEA2x2FTP | |||
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.8.1 | ScalarwtWebio577xxEA2x2FTPServerIP | read-write | mandatory | Name or IP address of the FTP server, which accepts the FTP messages. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.8.2 | ScalarwtWebio577xxEA2x2FTPServerControlPort | read-write | mandatory | Portnumber of the control port of the FTP server, default 21. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.8.3 | ScalarwtWebio577xxEA2x2FTPUserName | read-write | mandatory | FTP Loggin: user name. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.8.4 | ScalarwtWebio577xxEA2x2FTPPassword | read-write | mandatory | FTP Loggin: user password. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.8.5 | ScalarwtWebio577xxEA2x2FTPAccount | read-write | mandatory | FTP Loggin: name of account. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.8.6 | ScalarwtWebio577xxEA2x2FTPOption | read-write | mandatory | Bit 0 switches the FTP Server in Passiv-Mode, the Client controls the data connection on its own: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit … |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.8.7 | ScalarwtWebio577xxEA2x2FTPEnable | read-write | mandatory | Set Bit 0 to enable FTP: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : FTP enable |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.12 | NodewtWebio577xxEA2x2MQTT | |||
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.12.1 | ScalarwtWebio577xxEA2x2MQTTEnable | read-write | mandatory | Bit 7 schaltet MQTT frei: Octet 1: ungenutzt Octet 2: ungenutzt Octet 3: ungenutzt Octet 4: Bit 0-6: ungenutzt Bit 7 : MQTT enable |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.12.2 | ScalarwtWebio577xxEA2x2MQTTBrockerIP | read-write | mandatory | Name or IP-address of the MQTT-Server. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.12.3 | ScalarwtWebio577xxEA2x2MQTTUserName | read-write | mandatory | MQTT login user name. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.12.4 | ScalarwtWebio577xxEA2x2MQTTPassword | read-write | mandatory | MQTT login password. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.12.5 | ScalarwtWebio577xxEA2x2MQTTLocalPort | read-write | mandatory | Local port number. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.12.6 | ScalarwtWebio577xxEA2x2MQTTBrokerServerPort | read-write | mandatory | MQTT Server port number. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.12.7 | ScalarwtWebio577xxEA2x2MQTTInterval | read-write | mandatory | Ping intervall, if no data has to be send: time in seconds. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.12.8 | ScalarwtWebio577xxEA2x2MQTTLastWillEnable | read-write | mandatory | Bit 0 activate MQTT LastWill message: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : MQTT Last will enable |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.12.9 | ScalarwtWebio577xxEA2x2MQTTLastWillTopic | read-write | mandatory | MQTT Last Will Topic. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.12.10 | ScalarwtWebio577xxEA2x2MQTTLastWillMsg | read-write | mandatory | MQTT Last Will message. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.12.11 | ScalarwtWebio577xxEA2x2MQTTLastWillQoS | read-write | mandatory | Binary coded MQTT Publish QoS: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: QoS 0 Bit 1: QoS 1 Bit 2: QoS 2 Bit 3-7:unused |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.12.12 | ScalarwtWebio577xxEA2x2MQTTLastWillRetain | read-write | mandatory | Binary coded MQTT Publish Retain properties: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0 : retain enable Bit 1-7 : unused |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.12.13 | ScalarwtWebio577xxEA2x2MQTTLastWillConnectEnable | read-write | mandatory | Bit 0 activate MQTT LastWill Connect message: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : MQTT Last will connect message e… |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.12.14 | ScalarwtWebio577xxEA2x2MQTTLastWillConnectMsg | read-write | mandatory | MQTT Last Will Connect message will be send with the QoS and Retain settings of the LastWill message. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.13 | NodewtWebio577xxEA2x2REST | |||
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.13.1 | ScalarwtWebio577xxEA2x2RESTEnable | read-write | mandatory | Bit 0 activates REST: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : REST enable |
| 1.3.6.1.4.1.5040.1.2.52.3.1.3.13.2 | ScalarwtWebio577xxEA2x2RESTDigestAuthEnable | read-write | mandatory | Bit 0 activates Digest-Authentification: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Digest Auth enable |
| 1.3.6.1.4.1.5040.1.2.52.3.1.4 | NodewtWebio577xxEA2x2OutputMode | |||
| 1.3.6.1.4.1.5040.1.2.52.3.1.4.1 | TablewtWebio577xxEA2x2OutputModeTable | not-accessible | mandatory | Table of output mode configurations dependent on the output indices. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.4.1.1 | RowwtWebio577xxEA2x2OutputModeEntry | not-accessible | mandatory | Output mode configurations of the individual outputs. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.4.1.1.1 | ColumnwtWebio577xxEA2x2OutputModeBit | read-write | mandatory | This binary coded output mode defines the individual operation mode for any output. More than one mode must not be selected. The OCTETS are interpreted bit-by-… |
| 1.3.6.1.4.1.5040.1.2.52.3.1.4.2 | ScalarwtWebio577xxEA2x2SafetyTimeout | read-write | mandatory | After this period of time (multiple of 100ms) without receiving data outputs switch to their Safety States. For each output a independend safety state could be… |
| 1.3.6.1.4.1.5040.1.2.52.3.1.4.4 | ScalarwtWebio577xxEA2x2PowerSupplyEnable | read-write | mandatory | Activate the 24V power supply.. . Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Power supply enable |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5 | NodewtWebio577xxEA2x2Alarm | |||
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.1 | ScalarwtWebio577xxEA2x2AlarmCount | read-only | mandatory | Number of independent alarms. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.2 | TablewtWebio577xxEA2x2AlarmIfTable | not-accessible | mandatory | List of alarm indices. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.2.1 | RowwtWebio577xxEA2x2AlarmIfEntry | not-accessible | mandatory | Numbers of the alarms. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.2.1.1 | ColumnwtWebio577xxEA2x2AlarmNo | read-only | mandatory | Numbers of the alarms. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3 | TablewtWebio577xxEA2x2AlarmTable | not-accessible | mandatory | List of settings depending on the alarm number. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1 | RowwtWebio577xxEA2x2AlarmEntry | not-accessible | mandatory | Alarm parameters of the individual alarms. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.1 | ColumnwtWebio577xxEA2x2AlarmInputTrigger | read-write | mandatory | This variable allows setting of individual input trigger conditions. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an input. Bit 0 corr… |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.2 | ColumnwtWebio577xxEA2x2AlarmOutputTrigger | read-write | mandatory | This variable allows setting of individual output trigger conditions. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 co… |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.3 | ColumnwtWebio577xxEA2x2AlarmSystemTrigger | read-write | mandatory | Binary coded trigger conditions: The OCTETS are interpreted bit-by-bit. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, … |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.4 | ColumnwtWebio577xxEA2x2AlarmMaxCounterValue | read-write | mandatory | This variable configures a max. counter value. If an input counter value exceeds this max. value, the corresponding alarm is triggered. Input counters with its… |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.5 | ColumnwtWebio577xxEA2x2AlarmInterval | read-write | mandatory | Send interval for alarm messages. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.6 | ColumnwtWebio577xxEA2x2AlarmEnable | read-write | mandatory | Binary coded alarm enable: Octet 1: unused Octet 2: unused Bit 0: UDP enable Bit1-7: unused Octet 4: Bit 0: Mail Enable Bit 1: SNMP Trap enable Bit 2: TCP Clie… |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.7 | ColumnwtWebio577xxEA2x2AlarmMailAddr | read-write | mandatory | E-Mail address for sending the alarm mail to. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.8 | ColumnwtWebio577xxEA2x2AlarmMailSubject | read-write | mandatory | Subject line for alarm mail. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.9 | ColumnwtWebio577xxEA2x2AlarmMailText | read-write | mandatory | Alarm mail text: States of the Webio device can be included by using special tags. Please refer to the respective Webio manual |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.10 | ColumnwtWebio577xxEA2x2AlarmSnmpManagerIP | read-write | mandatory | IP address of the SNMP Manager to which the Webio device should send SNMP traps. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.11 | ColumnwtWebio577xxEA2x2AlarmSnmpTrapText | read-write | mandatory | This text appears in the trap body. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.12 | ColumnwtWebio577xxEA2x2AlarmUdpIpAddr | read-write | mandatory | IP address of the UDP listener to which the Webio device should send UDP traps. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.13 | ColumnwtWebio577xxEA2x2AlarmUdpPort | read-write | mandatory | Port number of the UDP listener to which the Webio device should send UDP traps. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.14 | ColumnwtWebio577xxEA2x2AlarmUdpText | read-write | mandatory | This text appears in the UDP trap body. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.15 | ColumnwtWebio577xxEA2x2AlarmTcpIpAddr | read-write | mandatory | IP address of the TCP listener to which the Webio device should send TCP traps. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.16 | ColumnwtWebio577xxEA2x2AlarmTcpPort | read-write | mandatory | Port number of the TCP listener to which the Webio device should send TCP traps. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.17 | ColumnwtWebio577xxEA2x2AlarmTcpText | read-write | mandatory | This text appears in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.18 | ColumnwtWebio577xxEA2x2AlarmSyslogIpAddr | read-write | mandatory | IP address of the syslog server to which the Webio device should send syslog messages. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.19 | ColumnwtWebio577xxEA2x2AlarmSyslogPort | read-write | mandatory | Port number of the syslog server to which the Webio device should send syslog messages. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.20 | ColumnwtWebio577xxEA2x2AlarmSyslogText | read-write | mandatory | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.21 | ColumnwtWebio577xxEA2x2AlarmFtpDataPort | read-write | mandatory | Local data port: 1..65535 or AUTO: the next free port will be assigned. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.22 | ColumnwtWebio577xxEA2x2AlarmFtpFileName | read-write | mandatory | Name of the file including path informations. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.23 | ColumnwtWebio577xxEA2x2AlarmFtpText | read-write | mandatory | Message text to store on the FTP server. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.24 | ColumnwtWebio577xxEA2x2AlarmFtpOption | read-write | mandatory | Binary coded options, select only one option at the same time: STORE = replace file APPEND = append message at the end of the file Octet 1: unused Octet 2: unu… |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.25 | ColumnwtWebio577xxEA2x2AlarmTimerCron | read-write | mandatory | This entry contains 5 space or tab seperated text fields for time trigger definition. Each field must match with the actual time to trigger a message, weekday … |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.26 | ColumnwtWebio577xxEA2x2AlarmMailReleaseSubject | read-write | mandatory | Subject line for alarm mail. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.27 | ColumnwtWebio577xxEA2x2AlarmMailReleaseText | read-write | mandatory | Release Alarm mail text: States of the Webio device can be included by using special tags. Please refer to the respective Webio manual |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.28 | ColumnwtWebio577xxEA2x2AlarmSnmpTrapReleaseText | read-write | mandatory | This text appears in the trap body. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.29 | ColumnwtWebio577xxEA2x2AlarmUdpReleaseText | read-write | mandatory | This text appears in the UDP trap body. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.30 | ColumnwtWebio577xxEA2x2AlarmTcpReleaseText | read-write | mandatory | This text appears in the TCP trap body. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.31 | ColumnwtWebio577xxEA2x2AlarmSyslogReleaseText | read-write | mandatory | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.32 | ColumnwtWebio577xxEA2x2AlarmFtpReleaseText | read-write | mandatory | Message text to store on the FTP server. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.34 | ColumnwtWebio577xxEA2x2AlarmGlobalEnable | read-write | mandatory | Binary coded alarm activation: Bit 0 = LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bit 1-7: unused Bit 0 : Alarm enable |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.58 | ColumnwtWebio577xxEA2x2AlarmCombinationLogic | read-write | mandatory | Binary coded logic: Bit 0 = LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bit 2-7: unused Bit 1 : OR Bit 0 : AND |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.59 | ColumnwtWebio577xxEA2x2AlarmTrgMqttTopic | read-write | mandatory | MQTT subscribe topic. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.60 | ColumnwtWebio577xxEA2x2AlarmTrgMqttTopicText | read-write | mandatory | Reveiving this message from the MQTT Broker, this alarm will be triggered. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.61 | ColumnwtWebio577xxEA2x2AlarmHttpReqAuthEnable | read-write | mandatory | Binnary coded value: Bit 0 = LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bit 1-7: unused Bit 0 : HHTP Request Authentication enable |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.62 | ColumnwtWebio577xxEA2x2AlarmHttpReqAuthUser | read-write | mandatory | HTTP Request: User |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.63 | ColumnwtWebio577xxEA2x2AlarmHttpReqAuthPassword | read-write | mandatory | HTTP Request: Password |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.64 | ColumnwtWebio577xxEA2x2AlarmHttpReqSetUrl | read-write | mandatory | HTTP Request: Set URL |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.65 | ColumnwtWebio577xxEA2x2AlarmHttpReqClearUrl | read-write | mandatory | HTTP Request: Clear URL |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.66 | ColumnwtWebio577xxEA2x2AlarmHttpReqServerPort | read-write | mandatory | HTTP Request: Server Port |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.67 | ColumnwtWebio577xxEA2x2AlarmMqttTopicPath | read-write | mandatory | MQTT Publish: Topic path |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.68 | ColumnwtWebio577xxEA2x2AlarmMqttTopicSetTopic | read-write | mandatory | MQTT Publish: Topic SET message |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.69 | ColumnwtWebio577xxEA2x2AlarmMqttTopicClear | read-write | mandatory | MQTT Publish: Topic CLEAR message |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.70 | ColumnwtWebio577xxEA2x2AlarmSetOutputsOwn | read-write | mandatory | This variable allows setting of individual output. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds to the LS… |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.71 | ColumnwtWebio577xxEA2x2AlarmSetOutputsServerIp | read-write | mandatory | Set Outputs: Server IP Address |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.72 | ColumnwtWebio577xxEA2x2AlarmSetOutputsServerPort | read-write | mandatory | Set Outputs: Server Port |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.73 | ColumnwtWebio577xxEA2x2AlarmSetOutputsServerPassword | read-write | mandatory | Set Outputs: Server Pasword |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.74 | ColumnwtWebio577xxEA2x2AlarmSetOutputsServerOutputs | read-write | mandatory | This variable allows setting of individual output. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds to the LS… |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.75 | ColumnwtWebio577xxEA2x2AlarmSetOutputsDest | read-write | mandatory | Binary coded value: Bit 0 = LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bit 2-7: unused Bit 1 : set outputs of remote server. Bit 0 : set out… |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.76 | ColumnwtWebio577xxEA2x2AlarmSnmpManagerPort | read-write | mandatory | Port number of the SNMP Manager to which the Webio device should send SNMP traps. |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.77 | ColumnwtWebio577xxEA2x2AlarmMqttQoS | read-write | mandatory | Binary coded value: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: QoS 0 Bit 1: QoS 1 Bit 2: QoS 2 Bit 3-7:unused |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.3.1.78 | ColumnwtWebio577xxEA2x2AlarmMqttRetain | read-write | mandatory | Binary coded value: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0 : retain enable Bit 1-7 : unused |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.4 | ScalarwtWebio577xxEA2x2LoadControlView | read-only | mandatory | Here the result of automatic load control can be read. All output were tested in pairs (0-1). If an error occours at one output, both output of an pair will be… |
| 1.3.6.1.4.1.5040.1.2.52.3.1.5.5 | ScalarwtWebio577xxEA2x2LCShutDownView | read-write | mandatory | Here the result of the automatic load control shut down can be read. All outputs remain switched of, until a zero is written into this variable. But previously… |
| 1.3.6.1.4.1.5040.1.2.52.3.2 | NodewtWebio577xxEA2x2Ports | |||
| 1.3.6.1.4.1.5040.1.2.52.3.2.1 | TablewtWebio577xxEA2x2InputPortTable | not-accessible | mandatory | List of settings depending on the input number. |
| 1.3.6.1.4.1.5040.1.2.52.3.2.1.1 | RowwtWebio577xxEA2x2InputPortEntry | not-accessible | mandatory | Input parameter for the individual inputs. |
| 1.3.6.1.4.1.5040.1.2.52.3.2.1.1.1 | ColumnwtWebio577xxEA2x2PortInputName | read-write | mandatory | Name of the input. |
| 1.3.6.1.4.1.5040.1.2.52.3.2.1.1.2 | ColumnwtWebio577xxEA2x2PortInputText | read-write | mandatory | Description of the input. |
| 1.3.6.1.4.1.5040.1.2.52.3.2.1.1.3 | ColumnwtWebio577xxEA2x2PortInputMode | read-write | mandatory | Binary coded modes: Selecting short pulse detection enable by setting the corresponding bit to 1 enables interrupt support for counting. Only positive edges ar… |
| 1.3.6.1.4.1.5040.1.2.52.3.2.1.1.4 | ColumnwtWebio577xxEA2x2PortInputFilter | read-write | mandatory | Pulses with a duration shorter than here specified (duration in 1/1000 sec), are ignored. |
| 1.3.6.1.4.1.5040.1.2.52.3.2.1.1.5 | ColumnwtWebio577xxEA2x2PortInputBicountPulsePolarity | read-write | mandatory | This value defines the polarity of the input pulse. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 0 : negative polarity Bit 1 : positive polarit… |
| 1.3.6.1.4.1.5040.1.2.52.3.2.1.1.6 | ColumnwtWebio577xxEA2x2PortInputBicountInactivTimeout | read-write | mandatory | Pulse chains with a duration shorter than here specified (in 1/10 sek), are ignored. |
| 1.3.6.1.4.1.5040.1.2.52.3.2.2 | TablewtWebio577xxEA2x2OutputPortTable | not-accessible | mandatory | List of settings depending on the output number. |
| 1.3.6.1.4.1.5040.1.2.52.3.2.2.1 | RowwtWebio577xxEA2x2OutputPortEntry | not-accessible | mandatory | Output parameters of the individual outputs. |
| 1.3.6.1.4.1.5040.1.2.52.3.2.2.1.1 | ColumnwtWebio577xxEA2x2PortOutputName | read-write | mandatory | Name of the output. |
| 1.3.6.1.4.1.5040.1.2.52.3.2.2.1.2 | ColumnwtWebio577xxEA2x2PortOutputText | read-write | mandatory | Description of the output. |
| 1.3.6.1.4.1.5040.1.2.52.3.2.2.1.3 | ColumnwtWebio577xxEA2x2PortOutputGroupMode | read-write | mandatory | It is possible to connect outputs together to increase the output current. This could be done by connecting 2 or 4 outputs in a group together. All bits of suc… |
| 1.3.6.1.4.1.5040.1.2.52.3.2.2.1.4 | ColumnwtWebio577xxEA2x2PortOutputSafetyState | read-write | mandatory | This variable allows setting of individual digital outputs. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds … |
| 1.3.6.1.4.1.5040.1.2.52.3.2.2.1.5 | ColumnwtWebio577xxEA2x2PortLogicInputMask | read-write | mandatory | Selecting one of these inputs by setting the corresponding bit to 1 enables the logic function for the output identified by the index within this table. The ca… |
| 1.3.6.1.4.1.5040.1.2.52.3.2.2.1.6 | ColumnwtWebio577xxEA2x2PortLogicInputInverter | read-write | mandatory | Every input bit selected here will be inverted. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 0-1 : inputs 0-1 |
| 1.3.6.1.4.1.5040.1.2.52.3.2.2.1.7 | ColumnwtWebio577xxEA2x2PortLogicFunction | read-write | mandatory | This determines the logic function. No more than one function may be selected. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 0 : logic function … |
| 1.3.6.1.4.1.5040.1.2.52.3.2.2.1.8 | ColumnwtWebio577xxEA2x2PortLogicOutputInverter | read-write | mandatory | The logical operation result could be inverteted by setting the corresponding bit to 1. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 0 : Output… |
| 1.3.6.1.4.1.5040.1.2.52.3.2.2.1.9 | ColumnwtWebio577xxEA2x2PortPulseDuration | read-write | mandatory | Pulse length in 1/1000 sec. Setting this value to zero, disables the pulse output. |
| 1.3.6.1.4.1.5040.1.2.52.3.2.2.1.10 | ColumnwtWebio577xxEA2x2PortPulsePolarity | read-write | mandatory | This value defines the polarity of the output pulse, if wtWebio577xxEA2x2PortPulseDuration is not set to zero. After the pulse is finished, the output switches… |
| 1.3.6.1.4.1.5040.1.2.52.3.3 | NodewtWebio577xxEA2x2Manufact | |||
| 1.3.6.1.4.1.5040.1.2.52.3.3.1 | ScalarwtWebio577xxEA2x2MfName | read-write | mandatory | Manufacturer company name |
| 1.3.6.1.4.1.5040.1.2.52.3.3.2 | ScalarwtWebio577xxEA2x2MfAddr | read-write | mandatory | Manufacturer address. |
| 1.3.6.1.4.1.5040.1.2.52.3.3.3 | ScalarwtWebio577xxEA2x2MfHotline | read-write | mandatory | Manufacturer hotline. |
| 1.3.6.1.4.1.5040.1.2.52.3.3.4 | ScalarwtWebio577xxEA2x2MfInternet | read-write | mandatory | Manufacturer Internet address. |
| 1.3.6.1.4.1.5040.1.2.52.3.3.5 | ScalarwtWebio577xxEA2x2MfDeviceTyp | read-write | mandatory | Manufacturer device name (model number). |
| 1.3.6.1.4.1.5040.1.2.52.4 | NodewtWebio577xxEA2x2Diag | |||
| 1.3.6.1.4.1.5040.1.2.52.4.1 | ScalarwtWebio577xxEA2x2DiagErrorCount | read-only | mandatory | Number of entries in the error memory. |
| 1.3.6.1.4.1.5040.1.2.52.4.2 | ScalarwtWebio577xxEA2x2DiagBinaryError | read-only | mandatory | Error causes coded bit-by-bit. |
| 1.3.6.1.4.1.5040.1.2.52.4.3 | ScalarwtWebio577xxEA2x2DiagErrorIndex | read-write | mandatory | The value of this variable is used as an index to read an error massege from wtWebio577xxEA2x2DiagErrorMessage. Errors are numbered from 1 to wtWebio577xxEA2x2… |
| 1.3.6.1.4.1.5040.1.2.52.4.4 | ScalarwtWebio577xxEA2x2DiagErrorMessage | read-only | mandatory | Using wtWebio577xxEA2x2DiagErrorIndex as an index, the appropriate message is available. |
| 1.3.6.1.4.1.5040.1.2.52.4.5 | ScalarwtWebio577xxEA2x2DiagErrorClear | write-only | mandatory | Writing 1 into this variable clears all diagnosis messages. |
| 1.3.6.1.4.1.5040.1.2.52.41 | NodewtWebio577xxEA2x2Alert1 | This SNMP trap is generated when Alarm 1 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.52.42 | NodewtWebio577xxEA2x2Alert2 | This SNMP trap is generated when Alarm 2 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.52.43 | NodewtWebio577xxEA2x2Alert3 | This SNMP trap is generated when Alarm 3 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.52.44 | NodewtWebio577xxEA2x2Alert4 | This SNMP trap is generated when Alarm 4 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.52.45 | NodewtWebio577xxEA2x2Alert5 | This SNMP trap is generated when Alarm 5 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.52.46 | NodewtWebio577xxEA2x2Alert6 | This SNMP trap is generated when Alarm 6 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.52.47 | NodewtWebio577xxEA2x2Alert7 | This SNMP trap is generated when Alarm 7 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.52.48 | NodewtWebio577xxEA2x2Alert8 | This SNMP trap is generated when Alarm 8 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.52.49 | NodewtWebio577xxEA2x2Alert9 | This SNMP trap is generated when Alarm 9 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.52.50 | NodewtWebio577xxEA2x2Alert10 | This SNMP trap is generated when Alarm 10 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.52.51 | NodewtWebio577xxEA2x2Alert11 | This SNMP trap is generated when Alarm 11 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.52.52 | NodewtWebio577xxEA2x2Alert12 | This SNMP trap is generated when Alarm 12 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.52.71 | NodewtWebio577xxEA2x2Alert13 | This SNMP trap is generated when Alarm 1 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.52.72 | NodewtWebio577xxEA2x2Alert14 | This SNMP trap is generated when Alarm 2 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.52.73 | NodewtWebio577xxEA2x2Alert15 | This SNMP trap is generated when Alarm 3 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.52.74 | NodewtWebio577xxEA2x2Alert16 | This SNMP trap is generated when Alarm 4 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.52.75 | NodewtWebio577xxEA2x2Alert17 | This SNMP trap is generated when Alarm 5 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.52.76 | NodewtWebio577xxEA2x2Alert18 | This SNMP trap is generated when Alarm 6 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.52.77 | NodewtWebio577xxEA2x2Alert19 | This SNMP trap is generated when Alarm 7 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.52.78 | NodewtWebio577xxEA2x2Alert20 | This SNMP trap is generated when Alarm 8 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.52.79 | NodewtWebio577xxEA2x2Alert21 | This SNMP trap is generated when Alarm 9 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.52.80 | NodewtWebio577xxEA2x2Alert22 | This SNMP trap is generated when Alarm 10 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.52.81 | NodewtWebio577xxEA2x2Alert23 | This SNMP trap is generated when Alarm 11 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.52.82 | NodewtWebio577xxEA2x2Alert24 | This SNMP trap is generated when Alarm 12 was released, SNMP trap enable is set and SNMP is enabled. | ||
| 1.3.6.1.4.1.5040.1.2.52.110 | NodewtWebio577xxEA2x2AlertDiag | This SNMP trap is generated when a diagnosis/error message was triggered, SNMP trap enable is set and SNMP is enabled. |