ZHONE-PHY-WTN-RADIO-MIB
63 objects
Module for radio provisioning and status.
Imported Objects
| IF-MIB | InterfaceIndex |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-SMI | Gauge32 Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE |
| SNMPv2-TC | TimeStamp TruthValue |
| Zhone | zhoneModules zhoneRadio |
| ZHONE-RADIO-TC-MIB | SkyZhoneRadioChannelNumber SkyZhoneScientificNotation |
| Zhone-TC | ZhoneAdminString |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.5504.5.8.1 | TablewtnConfigTable | not-accessible | current | Radio, modem and ODU configuration information. An entry is automatically created for each radio/modem/ODU interface. |
| 1.3.6.1.4.1.5504.5.8.1.1 | RowwtnConfigEntry | not-accessible | current | Configuration entries |
| 1.3.6.1.4.1.5504.5.8.1.1.1 | ColumnwtnRadioIfIndex | not-accessible | current | This object should be made equal to the Ifindex used for the radio interface. |
| 1.3.6.1.4.1.5504.5.8.1.1.2 | ColumnwtnActiveChannelNumber | read-write | current | Assigns one of N allowed frequency pairs for the radio transmitter and reciever as described in zhoneRadio-TC.mib. 5.7Ghz family (sysObjId) systems: Writing to… |
| 1.3.6.1.4.1.5504.5.8.1.1.3 | ColumnwtnActiveTransmitFrequency | read-write | current | Current transmit frequency. As described in zhoneRadio-TC.mib. 23Ghz family: ( according to sysObjId ) The transmit frequency is entered as a floating point nu… |
| 1.3.6.1.4.1.5504.5.8.1.1.4 | ColumnwtnStandbyChannelNumber | read-write | current | Assigns one of N allowed standby frequency pairs to the radio transmitter and reciever as described in zhoneRadio-TC.mib. 5.7Ghz family (sysObjId) systems: Sel… |
| 1.3.6.1.4.1.5504.5.8.1.1.5 | ColumnwtnStandbyTransmitFrequency | read-write | current | Standby Transmit frequency as described in zhoneRadio-TC.mib. 23Ghz family: ( according to sysObjId ) If auto-switching is enabled, the frequency shown will be… |
| 1.3.6.1.4.1.5504.5.8.1.1.6 | ColumnwtnAutoChannelSwitchEnable | read-write | current | true(1) - allows radio to automatically switch to the standby channel in case of active channel interference. false(2) - inhibits radio from automatically swit… |
| 1.3.6.1.4.1.5504.5.8.1.1.7 | ColumnwtnChannelSeparation | read-write | current | 23Ghz family (sysObjId) systems: Channel separation - the fixed difference between transmit and receive frequency. Only three values are allowed: s1232MHz(1), … |
| 1.3.6.1.4.1.5504.5.8.1.1.8 | ColumnwtnRadioAmplifiersEnable | read-write | current | true(1) - Enables amplifiers for transmitter and receiver. The radio will begin transmitting and receiving data. If the ODU is looped back, unable to lock onto… |
| 1.3.6.1.4.1.5504.5.8.1.1.9 | ColumnwtnRxBERThresh | read-write | current | Set point of BER alarm. When the modem BER estimate is higher than this value, a modem BER alarm will occur. The BER over threshold Causes trap wtnBerAlarm to … |
| 1.3.6.1.4.1.5504.5.8.1.1.10 | ColumnwtnRxBERHysteresisWindow | read-write | current | After a wtnBerAlarm trap is sent, it is revoked using the same trap with the condition flag set to false when the modem BER estimate is lower than the set poin… |
| 1.3.6.1.4.1.5504.5.8.1.1.11 | ColumnwtnAntennaSize | read-write | current | Initial power of transmitter is based upon antenna diameter. oneFoot(1) - a one foot dish twoFeet(2) - a two foot dish fourFeet(4) - a four foot dish sixFeet(6… |
| 1.3.6.1.4.1.5504.5.8.1.1.12 | ColumnwtnIduOduCableLength | read-write | current | The length of the coaxial cable between the Indoor Unit and the Outdoor Unit. Used internally to compensate for the coaxial cable's natural attenuation of the … |
| 1.3.6.1.4.1.5504.5.8.1.1.13 | ColumnwtnRssiThresh | read-write | current | Set point of RSSI thresholdalarm. When the ODU RSSI estimate is lower than this value, a wtnRssiDeviation trap will be emitted. When the ODU RSSI estimate is h… |
| 1.3.6.1.4.1.5504.5.8.1.1.14 | ColumnwtnRssiHysteresisWindow | read-write | current | After a wtnRssiDeviation Trap is sent, an the trap is re-emitted with the condition flag set to false when the ODU RSSI estimate is higher than the set point w… |
| 1.3.6.1.4.1.5504.5.8.1.1.15 | ColumnwtnTrapsEnable | read-write | current | When true(1), radio traps may be emitted. When false(2), radio traps will be absorbed. Default value is true(1) = enabled. |
| 1.3.6.1.4.1.5504.5.8.1.1.16 | ColumnwtnOduLoopback | read-write | current | loopbackOn(1) - engages the loopback function at the ODU (outdoor unit). Data normally transmitted by the radio is instead returned to the IDU (indoor unit). T… |
| 1.3.6.1.4.1.5504.5.8.1.1.17 | ColumnwtnOduIdentifier | read-write | current | Textual description of ODU. This string typically identifies the location of antenna. |
| 1.3.6.1.4.1.5504.5.8.1.1.18 | ColumnwtnTxLevel | read-write | current | Desired transmitter signal strength (TSSI) at antenna. Note: Accuracy decreases as power levels decrease below 20dBm. FCC maximum power allowed is +30dBm. |
| 1.3.6.1.4.1.5504.5.8.2 | TablewtnStatusTable | not-accessible | current | Contains the status of the Radio, ODU and Modem. |
| 1.3.6.1.4.1.5504.5.8.2.1 | RowwtnStatusEntry | not-accessible | current | Entries for radio, ODU and modem status. |
| 1.3.6.1.4.1.5504.5.8.2.1.1 | ColumnwtnCriticalAlarmStatus | read-only | current | Current radio alarm status details. BIT Hex Decimal BIT NAME Number Value Value 0 0x01 1 RSSI_DEVIATION 1 0x02 2 IDU_OOL 2 0x04 4 ODU_TEMP_ALERT 3 0x08 8 RX_BE… |
| 1.3.6.1.4.1.5504.5.8.2.1.2 | ColumnwtnCriticalAlarmStatusLastChange | read-only | current | Time Stamp of last change of critical alarm status wtnRadioCriticalAlmStatus. |
| 1.3.6.1.4.1.5504.5.8.2.1.3 | ColumnwtnMinorAlarmStatus | read-only | current | Current radio alarm status details. BIT Hex Decimal BIT NAME Number Value Value 0 0x01 1 RSSI_DEVIATION 1 0x02 2 IDU_OOL 2 0x04 4 ODU_TEMP_ALERT 3 0x08 8 RX_BE… |
| 1.3.6.1.4.1.5504.5.8.2.1.4 | ColumnwtnMinorAlarmStatusLastChange | read-only | current | Time Stamp of last change of minor alarm status wtnRadioMinorAlmStatus. |
| 1.3.6.1.4.1.5504.5.8.2.1.5 | ColumnwtnOduTemperature | read-only | current | Current temperature measured at local outdoor unit, in degrees Celsius (Centigrade). |
| 1.3.6.1.4.1.5504.5.8.2.1.6 | ColumnwtnReceiveFrequency | read-only | current | Current frequency at which radio receiver is set. |
| 1.3.6.1.4.1.5504.5.8.3 | TablewtnInfoTable | not-accessible | current | Table augments the wtnConfigTable |
| 1.3.6.1.4.1.5504.5.8.3.1 | RowwtnInfoEntry | not-accessible | current | Device information entries for the radio, modem and ODU. |
| 1.3.6.1.4.1.5504.5.8.3.1.1 | ColumnwtnOduSerialNumber | read-only | current | Manufacturing Serial Number for Outdoor Unit. Format of the serial number is XXXXX, where X = 0 to F. |
| 1.3.6.1.4.1.5504.5.8.3.1.2 | ColumnwtnOduMfgCLEICode | read-only | current | CLEI code for Outdoor Unit. |
| 1.3.6.1.4.1.5504.5.8.4 | TablewtnSnapshotTable | not-accessible | current | Table to collect statistics at radio demodulator of wireless transport node. |
| 1.3.6.1.4.1.5504.5.8.4.1 | RowwtnSnapshotEntry | not-accessible | current | Entry into wireless transport local radio status table. No rows may be added to this table. |
| 1.3.6.1.4.1.5504.5.8.4.1.1 | ColumnwtnRSSI | read-only | current | Current Received Signal Strength in dB as registered at the near end Outdoor Unit. This number is updated about once per second. Typical values range from -95d… |
| 1.3.6.1.4.1.5504.5.8.4.1.2 | ColumnwtnTSSI | read-only | current | Estimated transmitter signal strength (TSSI) at antenna. Note: maximum level allowed by FCC is 30dBm. |
| 1.3.6.1.4.1.5504.5.8.4.1.3 | ColumnwtnRxBerFloat | read-only | current | Current received BER at local Indoor Unit demodulator over the previous 250ms. |
| 1.3.6.1.4.1.5504.5.8.4.1.4 | ColumnwtnRcvEbNoFloat | read-only | current | Current local demodulator (rcvd) Energy-bit per noise. Conveys energy in each bit as compared to energy in noise. |
| 1.3.6.1.4.1.5504.5.8.5 | NodewtnTrapData | |||
| 1.3.6.1.4.1.5504.5.8.5.0 | NodewtnTraps | |||
| 1.3.6.1.4.1.5504.5.8.5.0.1 | NotificationwtnIduEquipFailCritical | current | Critical indoor equipment failure trap. Can be caused by: power supply failure, watchdog timeout, or other internal failure on indoor unit. | |
| 1.3.6.1.4.1.5504.5.8.5.0.2 | NotificationwtnIduEquipFail | current | Non-critical indoor equipment failure trap. Can be caused by: spurious power supply failure, or other temporary internal failure on indoor unit. | |
| 1.3.6.1.4.1.5504.5.8.5.0.3 | NotificationwtnIduOduLinkFailCritical | current | Critical failure of IDU to ODU communications link trap. can be caused by: IDU/ODU cable failure, bad connection, or equipment failure. | |
| 1.3.6.1.4.1.5504.5.8.5.0.4 | NotificationwtnIduOduLinkFail | current | Intermittent failure of IDU to ODU communications link trap. can be caused by: IDU/ODU cable failure, bad connection, or spurious equipment failure. | |
| 1.3.6.1.4.1.5504.5.8.5.0.5 | NotificationwtnIduOutOfLockCritical | current | Permanent or persistant loss of lock of internal clocks in indoor unit. | |
| 1.3.6.1.4.1.5504.5.8.5.0.6 | NotificationwtnIduOutOfLock | current | Spurious or intermittant loss of lock of internal clocks in indoor unit. | |
| 1.3.6.1.4.1.5504.5.8.5.0.7 | NotificationwtnMcChannelFailCritical | current | Radio overhead channel failure trap. May be caused by signal path degradation, or equipment failure on local or far end node. | |
| 1.3.6.1.4.1.5504.5.8.5.0.8 | NotificationwtnMcChannelFail | current | Spurious or intermittant radio overhead channel failure trap. May be caused by signal path degradation or equipment failure on local or far end node. | |
| 1.3.6.1.4.1.5504.5.8.5.0.9 | NotificationwtnOduEquipFailCritical | current | Critical ODU hardware failure trap. Possible causes: Synthesizer has lost desired frequency. Could be loss of reference signal from IDU or hardware error. Synt… | |
| 1.3.6.1.4.1.5504.5.8.5.0.10 | NotificationwtnOduEquipFail | current | Spurious or intermittant ODU hardware failure trap. Could be loss of reference signal from IDU or hardware error. | |
| 1.3.6.1.4.1.5504.5.8.5.0.11 | NotificationwtnOduTempAlertCritical | current | Significant deviation of ODU temperature from specified limits May be power amp heating up or environment heat buildup, or environment ice or frost. | |
| 1.3.6.1.4.1.5504.5.8.5.0.12 | NotificationwtnOduTempAlert | current | Warning to indicate that ODU is approaching a significant deviation of ODU temperature from specified limits. May be power amp heating up or environment heat b… | |
| 1.3.6.1.4.1.5504.5.8.5.0.13 | NotificationwtnRSSIDeviation | current | Receive signal strength at the odu is lower (in dB) than wtnOduRxRSSIThresh. This alarm will persist until the RSSI rises above wtnOduRxRSSIThresh - wtnOduRxRs… | |
| 1.3.6.1.4.1.5504.5.8.5.0.14 | NotificationwtnBerAlarm | current | Modem reports temporary BER > threshold alarm. Condition is true when current BER > wtnMdmRxBERThresh. Condition will persist until current BER < ( wtnMdmRxBER… | |
| 1.3.6.1.4.1.5504.5.8.5.0.15 | NotificationwtnEbNoAlarm | current | Modem reports temporary post-detection signal to noise ratio below preset threshold wtnMdmRxEbNoThresh. This condition will persist until the radio signal qual… | |
| 1.3.6.1.4.1.5504.5.8.5.1 | ScalarwtnTrapCondition | accessible-for-notify | current | Sent with wireless traps to indicate whether condition has arrived or has gone away. |
| 1.3.6.1.4.1.5504.5.8.5.2 | ScalarwtnServiceAffected | accessible-for-notify | current | Flag sent with each trap to indicate whether service may be affected by this particular trap condition. Service affecting means that payload data (DS3, etc) MA… |
| 1.3.6.1.4.1.5504.5.8.6 | TableradioTotalTable | not-accessible | current | Table of current statistics in the style of rfc2493 current table. |
| 1.3.6.1.4.1.5504.5.8.6.1 | RowradioTotalEntry | not-accessible | current | Set of basic statistics for radio interface. |
| 1.3.6.1.4.1.5504.5.8.6.1.1 | ColumnradioTotalES | read-write | current | Number of seconds the radio link detected bit errors since the system has been up, or since last reset. If the BER is above the user set threshhold then the re… |
| 1.3.6.1.4.1.5504.5.8.6.1.2 | ColumnradioTotalSES | read-write | current | Count of the number of seconds the radio endured severe conditions since system came up or value was reset. A severe condition occurs if: 1 - received BER is g… |
| 1.3.6.1.4.1.5504.5.8.6.1.3 | ColumnradioTotalUAS | read-write | current | Unavailable seconds. This value is incremented once per second after ten consecutive radioCurrentSES (severe-error seconds) are counted. An equipment failure w… |
| 1.3.6.1.4.1.5504.6.106 | IdentityzhonePhyWtnRadio | Module for radio provisioning and status. |