Zhone-VOICE-ANALOG-IF-MIB
86 objects
Analog Voice Interface MIB module. This MIB manages the E&M, FXO, FXS Interfaces in the Zhone's product.
Imported Objects
| IF-MIB | ifIndex InterfaceIndex |
| SNMPv2-SMI | Counter32 Integer32 MODULE-IDENTITY OBJECT-TYPE |
| SNMPv2-TC | TruthValue |
| Zhone | zhoneModules zhonePhysical |
| Zhone-TC | ZhoneRowStatus |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.5504.5.6 | NodezhoneVaIfObjects | |||
| 1.3.6.1.4.1.5504.5.6.1 | NodezhoneVaIfGeneralObjects | |||
| 1.3.6.1.4.1.5504.5.6.1.1 | TablezhoneVaIfCfgTable | not-accessible | current | The Analog Voice Standard Configuration Table. It contains the standard configuration information of the analog telephony interface. |
| 1.3.6.1.4.1.5504.5.6.1.1.1 | RowzhoneVaIfCfgEntry | not-accessible | current | An entry in the configuration table for each voice analog interface. The entry is created when the voice analog hardware is detected. |
| 1.3.6.1.4.1.5504.5.6.1.1.1.1 | ColumnzhoneVaIfCfgImpedance | read-write | current | Specifies the terminating impedance of voice analog interfaces. other - none of the following; arbitrary, within limits, for special cases. ohms600Real - 600 O… |
| 1.3.6.1.4.1.5504.5.6.1.1.1.2 | ColumnzhoneVaIfCfgReceiveTLP | read-write | current | Receive Transmission Level Point (RTLP) settings control the amount gain or loss added to the incoming signal after it is decoded to analog. to increase the si… |
| 1.3.6.1.4.1.5504.5.6.1.1.1.3 | ColumnzhoneVaIfCfgTransmitTLP | read-write | current | In case of FXO, it specifies FXO attenuation and default value is 0dB(fxsTtlp0db). In case of FXS this setting controls the amount of gain or loss added to a v… |
| 1.3.6.1.4.1.5504.5.6.1.1.1.4 | ColumnzhoneVaIfCfgTrunkConditioning | read-write | current | The trunk conditioning setting specifies whether the FXS/FXO port should send the idle pattern to the network upon declaration of a Carrier Group Alarm(CGA) on… |
| 1.3.6.1.4.1.5504.5.6.1.1.1.5 | ColumnzhoneVaIfCfgLineType | read-only | current | The Card type FXS, FXO, EM, EBS. Entries in the table will be created or deleted on the basis of zhoneVaIfCfgLineType in the zhoneVaIfCfgTable and we are not u… |
| 1.3.6.1.4.1.5504.5.6.1.1.1.6 | ColumnzhoneVaIfCfgIntegratedDSP | read-only | current | Indicates whether the interface has an integrated Digital Signal processing (DSP) unit. |
| 1.3.6.1.4.1.5504.5.6.1.1.1.7 | ColumnzhoneVaIfCfgLineCapabilities | read-only | current | The Interface types supported on this interface. This is a bit-map of possible types. This variable can be used to determine zhoneVaIfCfgLineType. |
| 1.3.6.1.4.1.5504.5.6.1.1.1.8 | ColumnzhoneVaIfCfgMaintenanceMode | read-write | current | Indicates the maintenance modes of the Analog voice interface. loopback options for Fxo and Fxs cards (Zhone specific) CODEC T1/E1 DS0 < Network PCM Bus ^ Digi… |
| 1.3.6.1.4.1.5504.5.6.1.1.1.9 | ColumnzhoneVaIfCfgPCMEncoding | read-write | current | alaw(1) :for E1 mulaw(2) : for T1 |
| 1.3.6.1.4.1.5504.5.6.1.1.1.10 | ColumnzhoneVaIfCfgReceiveTLPNum | read-write | current | Receive Transmission Level Point (RTLP) settings control the amount gain or loss added to the incoming signal after it is decoded to analog. to incrase the sig… |
| 1.3.6.1.4.1.5504.5.6.1.1.1.11 | ColumnzhoneVaIfCfgTransmitTLPNum | read-write | current | Transmit Transmission Level Point controls the amount of gain or loss added to a voice signal from CPE before it is encoded to digital PCM. To increase the sig… |
| 1.3.6.1.4.1.5504.5.6.1.1.1.12 | ColumnzhoneVaIfCfgLoopCurrent | read-write | current | To set the loop current value for a subscriber |
| 1.3.6.1.4.1.5504.5.6.1.1.1.13 | ColumnzhoneVaIfCfgRingVoltage | read-write | current | To set the ring voltage for a subscriber. |
| 1.3.6.1.4.1.5504.5.6.1.2 | TablezhoneVaIfStatusTable | not-accessible | current | The Analog Voice Status Table. It contains general information about the status of Analog Telephony interface including the error statistics. |
| 1.3.6.1.4.1.5504.5.6.1.2.1 | RowzhoneVaIfStatusEntry | not-accessible | current | An entry in the status table for each Analog voice interface. |
| 1.3.6.1.4.1.5504.5.6.1.2.1.1 | ColumnzhoneVaIfStatusSignalErrors | read-only | current | Accumulated number of signaling protocol errors that are detected in the interface since system startup. |
| 1.3.6.1.4.1.5504.5.6.1.2.1.2 | ColumnzhoneVaIfStatusInfoType | read-only | current | The information transfer services for the current call. none - no information transfer service, this is set befgore the first call is made on the interface. vo… |
| 1.3.6.1.4.1.5504.5.6.2 | NodezhoneVaIfFXSObjects | |||
| 1.3.6.1.4.1.5504.5.6.2.1 | TablezhoneVaIfFXSCfgTable | not-accessible | current | The FXS standard configuration table. It contains FXS configuration parameters, one entry per FXS interface. The configuration information of this table is set… |
| 1.3.6.1.4.1.5504.5.6.2.1.1 | RowzhoneVaIfFXSCfgEntry | not-accessible | current | An entry in the standard configuration table for each FXS interface. |
| 1.3.6.1.4.1.5504.5.6.2.1.1.1 | ColumnzhoneVaIfFXSCfgSignalType | read-write | current | the signaling type of FXS interface. fxsLoopStart - loop start. fxsGroundStart - ground start. fxsLoopStartFd fxsGroundStartAutomatic - Used with equipment req… |
| 1.3.6.1.4.1.5504.5.6.2.1.1.2 | ColumnzhoneVaIfFXSRingFrequency | read-write | current | the ring frequency to be used in the FXS interface. ringFrequency25 - ring frequency 25 Hertz. ringFrequency50 - ring frequency 50 Hertz. ringFrequency20 - rin… |
| 1.3.6.1.4.1.5504.5.6.2.1.1.3 | ColumnzhoneVaIfFXSRingBack | read-write | current | the ring back is requested if this variable is set to on. |
| 1.3.6.1.4.1.5504.5.6.2.2 | TablezhoneVaIfFXSStatusTable | not-accessible | current | The Foreign Exchange Station (FXS) interface Status Table. It contains hook status, ring active and other states of the interface. |
| 1.3.6.1.4.1.5504.5.6.2.2.1 | RowzhoneVaIfFXSStatusEntry | not-accessible | current | An entry in the status table for each FXS interface. |
| 1.3.6.1.4.1.5504.5.6.2.2.1.1 | ColumnzhoneVaIfFXSHookStatus | read-only | current | This object contains the hook status of FXS interface. onHook - the connected equipment(e.g., phone) is onHook. offHook - the connected equipment is offHook. |
| 1.3.6.1.4.1.5504.5.6.2.2.1.2 | ColumnzhoneVaIfFXSRingActive | read-only | current | This object contains the outgoing ring active indication. If the object value is true, then the interface is currently generating ring out to the Key Telephone… |
| 1.3.6.1.4.1.5504.5.6.2.2.1.3 | ColumnzhoneVaIfFXSRingGround | read-only | current | This object contains the incoming ring ground indication. It is only valid when the zvaIfFXSCfgSignalType is fxsGroundStart. If the object is true, then the in… |
| 1.3.6.1.4.1.5504.5.6.2.2.1.4 | ColumnzhoneVaIfFXSTipGround | read-only | current | This object contains the incoming tip ground indication. It is only valid when the zvaIfFXSCfgSignalType is fxsGroundStart. If the object is true, then the int… |
| 1.3.6.1.4.1.5504.5.6.2.3 | TablezhoneVaIfFXSTimingTable | not-accessible | current | The FXS interface Timing Parameters table. It contains the configuration of the various FXS signaling protocol timing parameters. |
| 1.3.6.1.4.1.5504.5.6.2.3.1 | RowzhoneVaIfFXSTimingEntry | not-accessible | current | An entry in the FXS Timing Parameters Table for each FXS interface. |
| 1.3.6.1.4.1.5504.5.6.2.3.1.1 | ColumnzhoneVaIfFXSTimingDigitDuration | read-write | current | Outgoing DTMF digit duration in milliseconds. The default value of this object is 100 milliseconds. This field is not supported. |
| 1.3.6.1.4.1.5504.5.6.2.3.1.2 | ColumnzhoneVaIfFXSTimingInterDigitDuration | read-write | current | Outgoing DTMF inter-digit duration in milliseconds. The default value of this object is 100 milliseconds. This field is not supported. |
| 1.3.6.1.4.1.5504.5.6.2.4 | TablezhonePotsRingTable | not-accessible | deprecated | Table to execute diagnostic potsring command. Row in table with non-zero timer will ring pots port. Currently, maximum of 4 rows at a time are supported. |
| 1.3.6.1.4.1.5504.5.6.2.4.1 | RowzhonePotsRingEntry | not-accessible | deprecated | potsring table entry |
| 1.3.6.1.4.1.5504.5.6.2.4.1.1 | ColumnzhonePotsRingIfIndex | not-accessible | deprecated | Physical pots interface. |
| 1.3.6.1.4.1.5504.5.6.2.4.1.2 | ColumnzhonePotsRingRingingCadence | read-create | deprecated | Ring cadence to use in test. |
| 1.3.6.1.4.1.5504.5.6.2.4.1.3 | ColumnzhonePotsRingTimer | read-create | deprecated | Time in seconds to continue ringing. |
| 1.3.6.1.4.1.5504.5.6.2.4.1.4 | ColumnzhonePotsRingRowStatus | read-create | deprecated | Row status |
| 1.3.6.1.4.1.5504.5.6.3 | NodezhoneVaIfFXOObjects | |||
| 1.3.6.1.4.1.5504.5.6.3.1 | TablezhoneVaIfFXOCfgTable | not-accessible | current | The FXO standard configuration table. It contains FXO configuration parameters, one entry per FXO interface. The configuration information of this table is set… |
| 1.3.6.1.4.1.5504.5.6.3.1.1 | RowzhoneVaIfFXOCfgEntry | not-accessible | current | An entry in the standard configuration table for each FXO interface. |
| 1.3.6.1.4.1.5504.5.6.3.1.1.1 | ColumnzhoneVaIfFXOCfgSignalType | read-write | current | the signaling type of FXO interface. fxoLoopStart - loop start. fxoGroundStart - ground start. fxodpt- Dial Pulse Terminating , this option allows the unit to … |
| 1.3.6.1.4.1.5504.5.6.3.1.1.2 | ColumnzhoneVaIfFXOCfgNumberRings | read-write | current | The number of rings detected before closing loop. The default value of this object is 1 ring. |
| 1.3.6.1.4.1.5504.5.6.3.1.1.3 | ColumnzhoneVaIfFXOCfgSupDisconnect | read-write | current | Specifies whether a supervisory disconnect signal (CPC) will be presented to the interface when the connected party at the interface hangs up. The default valu… |
| 1.3.6.1.4.1.5504.5.6.3.1.1.4 | ColumnzhoneVaIfFXOCfgDialType | read-write | current | Specifies the out dialing type of FXO interface. dtmf - DTMF digit. pulse - pulse. The default value of this object is dtmf(1). |
| 1.3.6.1.4.1.5504.5.6.3.2 | TablezhoneVaIfFXOStatusTable | not-accessible | current | The Foreign Exchange Office (FXO) interface Status Table. It contains hook status, ring detection and other states of the interface. |
| 1.3.6.1.4.1.5504.5.6.3.2.1 | RowzhoneVaIfFXOStatusEntry | not-accessible | current | An entry in the status table for each FXO interface. |
| 1.3.6.1.4.1.5504.5.6.3.2.1.1 | ColumnzhoneVaIfFXOHookStatus | read-only | current | This object contains the hook status of FXO interface. onHook - Present the onHook to the connected equipment. offHook - Present the offHook to the connected e… |
| 1.3.6.1.4.1.5504.5.6.3.2.1.2 | ColumnzhoneVaIfFXORingDetect | read-only | current | This object contains the ring detect indication. If the value is true, then the interface detects ring from PBX or CO; otherwise, it doesn't. |
| 1.3.6.1.4.1.5504.5.6.3.2.1.3 | ColumnzhoneVaIfFXORingGround | read-only | current | This object contains the incoming ring ground indication. It is only valid when the zvaIfFXOCfgSignalType is fxoGroundStart. If the object is true, then the in… |
| 1.3.6.1.4.1.5504.5.6.3.2.1.4 | ColumnzhoneVaIfFXOTipGround | read-only | current | This object contains the incoming tip ground indication. It is only valid when the zvaIfFXOCfgSignalType is fxoGroundStart. If the object is true, then the int… |
| 1.3.6.1.4.1.5504.5.6.3.3 | TablezhoneVaIfFXOTimingTable | not-accessible | current | The FXO interface Timing Parameters table. It contains the configuration of the various FXO signaling protocol timing parameters. |
| 1.3.6.1.4.1.5504.5.6.3.3.1 | RowzhoneVaIfFXOTimingEntry | not-accessible | current | An entry in the FXO Timing Parameters Table for each FXO interface. |
| 1.3.6.1.4.1.5504.5.6.3.3.1.1 | ColumnzhoneVaIfFXOTimingDigitDuration | read-write | current | Outgoing DTMF digit duration in milliseconds. The default value of this object is 100 msec. |
| 1.3.6.1.4.1.5504.5.6.3.3.1.2 | ColumnzhoneVaIfFXOTimingInterDigitDuration | read-write | current | Outgoing DTMF inter-digit duration in milliseconds. The default value of this object is 100 msec. |
| 1.3.6.1.4.1.5504.5.6.3.3.1.3 | ColumnzhoneVaIfFXOTimingPulseRate | read-write | current | Outgoing pulse dialing rate in pulses per second (pps). The default value of this object is 10 pps. |
| 1.3.6.1.4.1.5504.5.6.3.3.1.4 | ColumnzhoneVaIfFXOTimingPulseInterDigitDuration | read-write | current | Outgoing pulse dialing inter-digit timing in milliseconds. The default value of this object is 500 milliseconds. |
| 1.3.6.1.4.1.5504.5.6.4 | NodezhoneVaIfEMObjects | |||
| 1.3.6.1.4.1.5504.5.6.4.1 | TablezhoneVaIfEMCfgTable | not-accessible | current | The E&M standard configuration table. It contains the current setting of E&M configurable parameters. |
| 1.3.6.1.4.1.5504.5.6.4.1.1 | RowzhoneVaIfEMCfgEntry | not-accessible | current | An entry in the standard configuration table for each E&M tie trunk interface. |
| 1.3.6.1.4.1.5504.5.6.4.1.1.1 | ColumnzhoneVaIfEMCfgSignalType | read-only | current | The signaling type of E&M tie trunk interface. winkStart - the calling side seizes the line by going off-hook on its E lead but waits for a short off-hook 'win… |
| 1.3.6.1.4.1.5504.5.6.4.1.1.2 | ColumnzhoneVaIfEMCfgOperation | read-only | current | Specify the operation of the E&M signal. twoWires - 2-wire operation. fourWires - 4-wire operation. The default value of this object is twoWires(1). |
| 1.3.6.1.4.1.5504.5.6.4.1.1.3 | ColumnzhoneVaIfEMCfgType | read-write | current | Specifies the E&M Lead Signaling type. LEGEND: V = -48V /\/\/ = detector/resister X = normally open relay contact + = normally closed relay contact G = ground … |
| 1.3.6.1.4.1.5504.5.6.4.1.1.4 | ColumnzhoneVaIfEMCfgDialType | read-only | current | Specifies the out dialing type of E&M interface. dtmf - DTMF digit. pulse - pulse. The default value of this object is dtmf(1). |
| 1.3.6.1.4.1.5504.5.6.4.2 | TablezhoneVaIfEMStatusTable | not-accessible | current | The E&M interface Table. The table contains the status of the E&M tie trunk interface. |
| 1.3.6.1.4.1.5504.5.6.4.2.1 | RowzhoneVaIfEMStatusEntry | not-accessible | current | An entry in the status table for each E&M interface. |
| 1.3.6.1.4.1.5504.5.6.4.2.1.1 | ColumnzhoneVaIfEMInSeizureActive | read-only | current | This object contains the incoming seizure state of the E&M interface. If the value is true, then the interface has an incoming trunk seizure active; otherwise,… |
| 1.3.6.1.4.1.5504.5.6.4.2.1.2 | ColumnzhoneVaIfEMOutSeizureActive | read-only | current | This object contains the outgoing seizure state of the E&M interface. If the value is true, then the interface has an outgoing trunk seizure active; otherwise,… |
| 1.3.6.1.4.1.5504.5.6.4.3 | TablezhoneVaIfEMTimingTable | not-accessible | current | The E&M tie trunk Timing Parameters table. It contains the configuration of the various E&M signaling protocol timing parameters. |
| 1.3.6.1.4.1.5504.5.6.4.3.1 | RowzhoneVaIfEMTimingEntry | not-accessible | current | An entry in the E&M Timing Parameters Table for each E&M interface. |
| 1.3.6.1.4.1.5504.5.6.4.3.1.1 | ColumnzhoneVaIfEMTimingDigitDuration | read-write | current | Outgoing DTMF digit duration in milliseconds. The default value of this object is 100 milliseconds. |
| 1.3.6.1.4.1.5504.5.6.4.3.1.2 | ColumnzhoneVaIfEMTimingInterDigitDuration | read-write | current | Outgoing DTMF inter-digit duration in milliseconds. The default value of this object is 100 milliseconds. |
| 1.3.6.1.4.1.5504.5.6.4.3.1.3 | ColumnzhoneVaIfEMTimingPulseRate | read-write | current | Outgoing pulse dialing rate in pulses per second (pps). The default value of this object is 10 pps. |
| 1.3.6.1.4.1.5504.5.6.4.3.1.4 | ColumnzhoneVaIfEMTimingPulseInterDigitDuration | read-write | current | Outgoing Pulse dialing inter-digit timing in milliseconds. The default value of this object is 500 milliseconds. |
| 1.3.6.1.4.1.5504.5.6.4.3.1.5 | ColumnzhoneVaIfEMTimingClearWaitDuration | read-write | current | Time of Inactive seizure signal to declare call cleared. The default value of this object is 400 milliseconds. |
| 1.3.6.1.4.1.5504.5.6.4.3.1.6 | ColumnzhoneVaIfEMTimingMaxWinkWaitDuration | read-write | current | Maximum time to wait from the outgoing seizure of the line to the time of sending out a wink-pulse. The default value of this object is 200 milliseconds. |
| 1.3.6.1.4.1.5504.5.6.4.3.1.7 | ColumnzhoneVaIfEMTimingMaxWinkDuration | read-write | current | Maximum outgoing wink duration (between the wink-pulse leading edge and trailing edge) for wink start signaling. The default value of this object is 200 millis… |
| 1.3.6.1.4.1.5504.5.6.4.3.1.8 | ColumnzhoneVaIfEMTimingDelayStart | read-write | current | Minimum time to wait from outgoing seizure to out-dialing digits for delay start signaling. The default value of this object is 300 milliseconds. |
| 1.3.6.1.4.1.5504.5.6.4.3.1.9 | ColumnzhoneVaIfEMTimingMaxDelayDuration | read-write | current | Maximum time to wait from outgoing seizure to out-dialing digits. If the far end does not allow to send digits after the duration specified in the object, a re… |
| 1.3.6.1.4.1.5504.5.6.4.3.1.10 | ColumnzhoneVaIfEMTimingMinDelayPulseWidth | read-write | current | Minimum delay-dial pulse duration for incoming call. If the value of this object is 0, then no delay-dial is sent to the far end for the incoming call. The def… |
| 1.3.6.1.4.1.5504.6.13 | IdentityzhoneVoiceAnalogIf-MIB | Analog Voice Interface MIB module. This MIB manages the E&M, FXO, FXS Interfaces in the Zhone's product. |