adtran/ADTRAN-SHDSL-MIB
338 objects
This MIB defines the objects for the SHDSL MIB.
Imported Objects
| ADTRAN-GENPORT-MIB | adGenPortTrapIdentifier |
| ADTRAN-GENSLOT-MIB | adGenSlotInfoIndex |
| ADTRAN-GENTRAPINFORM-MIB | adTrapInformSeqNum |
| ADTRAN-SHARED-SHDSL-MIB MISSING | adGenEShdsl adGenEShdslID |
| ADTRAN-TAeSCUEXT1-MIB | adTAeSCUTrapAlarmLevel |
| IF-MIB | ifIndex |
| SNMPv2-CONF | NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-MIB | sysName |
| SNMPv2-SMI | Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE |
| SNMPv2-TC | DisplayString TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.664.5.59.1.1 | NodeadEShdslIndex | |||
| 1.3.6.1.4.1.664.5.59.1.1.1 | TableadEShdslIndexTable | not-accessible | current | This table declares the indeces to be used throughout the ADTRAN-SHDSL-MIB. |
| 1.3.6.1.4.1.664.5.59.1.1.1.1 | RowadEShdslIndexEntry | not-accessible | current | An entry in the adEShdslIndexTable. |
| 1.3.6.1.4.1.664.5.59.1.1.1.1.1 | ColumnadEShdslInvIndex | read-only | current | Each entry in this table corresponds to a physical element in a SHDSL Span. It is based on the EOC unit addressing scheme with reference to the xtuC. |
| 1.3.6.1.4.1.664.5.59.1.1.1.1.2 | ColumnadEShdslSideIndex | read-only | current | This is the referenced side of a SHDSL unit - Network or Customer side. The side facing the Network is the Network side, while the side facing the Customer is … |
| 1.3.6.1.4.1.664.5.59.1.1.1.1.3 | ColumnadEShdslWirePairIndex | read-only | current | This is the referenced pair of wires in a SHDSL Segment. |
| 1.3.6.1.4.1.664.5.59.1.2 | NodeadEShdslInventory | |||
| 1.3.6.1.4.1.664.5.59.1.2.1 | TableadEShdslInventoryTable | not-accessible | current | This table supports retrieval of unit inventory information available via the EOC from units in a SHDSL line. Entries in this table are dynamically created dur… |
| 1.3.6.1.4.1.664.5.59.1.2.1.1 | RowadEShdslInventoryEntry | not-accessible | current | An entry in the adEShdslInventoryTable. Each entry represents inventory information for a single unit in a SHDSL line. It is indexed by the ifIndex of the SHDS… |
| 1.3.6.1.4.1.664.5.59.1.2.1.1.1 | ColumnadEShdslInvVendorID | read-only | current | Vendor ID as reported in an Inventory Response message. |
| 1.3.6.1.4.1.664.5.59.1.2.1.1.2 | ColumnadEShdslInvVendorModelNumber | read-only | current | Vendor model number as reported in an Inventory Response message. |
| 1.3.6.1.4.1.664.5.59.1.2.1.1.3 | ColumnadEShdslInvVendorSerialNumber | read-only | current | Vendor serial number as reported in an Inventory Response message. |
| 1.3.6.1.4.1.664.5.59.1.2.1.1.4 | ColumnadEShdslInvStandardVersion | read-only | current | Version of the SHDSL standard implemented, as reported in an Inventory Response message. |
| 1.3.6.1.4.1.664.5.59.1.2.1.1.5 | ColumnadEShdslInvVendorListNumber | read-only | current | Vendor list number as reported in an Inventory Response message. |
| 1.3.6.1.4.1.664.5.59.1.2.1.1.6 | ColumnadEShdslInvVendorIssueNumber | read-only | current | Vendor issue number as reported in an Inventory Response message. |
| 1.3.6.1.4.1.664.5.59.1.2.1.1.7 | ColumnadEShdslInvVendorSoftwareVersion | read-only | current | Vendor software version as reported in an Inventory Response message. |
| 1.3.6.1.4.1.664.5.59.1.2.1.1.8 | ColumnadEShdslInvEquipmentCode | read-only | current | Equipment code conforming to ANSI T1.213, Coded Identification of Equipment Entities. |
| 1.3.6.1.4.1.664.5.59.1.2.1.1.9 | ColumnadEShdslInvVendorOther | read-only | current | Other vendor information as reported in an Inventory Response message. |
| 1.3.6.1.4.1.664.5.59.1.2.1.1.10 | ColumnadEShdslInvVendorEOCSoftwareVersion | read-only | current | Vendor EOC version as reported in a Discovery Response message. |
| 1.3.6.1.4.1.664.5.59.1.2.1.1.11 | ColumnadEShdslInvMfrDate | read-only | current | Optional Date of manufacture. Some products support. |
| 1.3.6.1.4.1.664.5.59.1.2.1.1.12 | ColumnadEShdslInvCircuitID | read-write | current | Optional Circuit ID assigned to all elements in the xdsl circuit. |
| 1.3.6.1.4.1.664.5.59.1.2.1.1.13 | ColumnadEShdslInvScratchPad | read-write | current | Optional Scratch Pad. 50 bytes long. |
| 1.3.6.1.4.1.664.5.59.1.2.1.1.14 | ColumnadEShdslInvDspHwVersion | read-only | current | Returns the hardware version of the DSP |
| 1.3.6.1.4.1.664.5.59.1.2.1.1.15 | ColumnadEShdslInvDspFwVersion | read-only | current | Returns the firmware version of the DSP |
| 1.3.6.1.4.1.664.5.59.1.2.1.1.16 | ColumnadEShdslInvElementPresent | read-only | current | Returns true(1) if the element specified by adEShdslInvIndex is present in the circuit. Returns false(2) otherwise |
| 1.3.6.1.4.1.664.5.59.1.2.1.1.17 | ColumnadEShdslInvPhysicalLinkId | read-only | current | Returns the physical link number associated with the element specified by adEShdslInvIndex. For example, a 2 port repeater would return 1 or 2 while an 8 port … |
| 1.3.6.1.4.1.664.5.59.1.3 | NodeadEShdslProvisioning | |||
| 1.3.6.1.4.1.664.5.59.1.3.1 | TableadEShdslProvTable | not-accessible | current | This table supports definitions of the configuration of SHDSL lines. |
| 1.3.6.1.4.1.664.5.59.1.3.1.1 | RowadEShdslProvEntry | not-accessible | current | An entry in the adEShdslProvTable. |
| 1.3.6.1.4.1.664.5.59.1.3.1.1.1 | ColumnadEShdslProvWireInterfaceMode | read-write | current | This object configures the two-wire or optional four-wire operation for SHDSL Lines. |
| 1.3.6.1.4.1.664.5.59.1.3.1.1.2 | ColumnadEShdslProvMinLineRate | read-write | current | This object configures the minimum transmission rate for the associated SHDSL Line in bits-per-second (bps). If the minimum line rate equals the maximum line r… |
| 1.3.6.1.4.1.664.5.59.1.3.1.1.3 | ColumnadEShdslProvMaxLineRate | read-write | current | This object configures the maximum transmission rate for the associated SHDSL Line in bits-per-second (bps). If the minimum line rate equals the maximum line r… |
| 1.3.6.1.4.1.664.5.59.1.3.1.1.4 | ColumnadEShdslProvG9912Annex | read-write | current | This object specifies the G991.2 Annex setting for the SHDSL line. |
| 1.3.6.1.4.1.664.5.59.1.3.1.1.5 | ColumnadEShdslProvCurrCondTargetMargin | read-write | current | This object specifies the current condition target SNR margin for a SHDSL line. The SNR margin is the difference between the desired SNR and the actual SNR. Ta… |
| 1.3.6.1.4.1.664.5.59.1.3.1.1.6 | ColumnadEShdslProvWorstCaseTargetMargin | read-write | current | This object specifies the worst case target SNR margin for a SHDSL line. The SNR margin is the difference between the desired SNR and the actual SNR. Target SN… |
| 1.3.6.1.4.1.664.5.59.1.3.1.1.7 | ColumnadEShdslProvUsedTargetMargins | read-only | current | Indicates which target SNR margin is enabled currently being used in line probing. This has no meaning if line probing is disabled. |
| 1.3.6.1.4.1.664.5.59.1.3.1.1.8 | ColumnadEShdslProvClockMode | read-write | current | This object configures the clock reference for the STU-C in a SHDSL Line. |
| 1.3.6.1.4.1.664.5.59.1.3.1.1.9 | ColumnadEShdslProvLineProbing | read-write | current | This object enables/disables support for Line Probe of the units in a SHDSL line. When Line Probe is enabled, the system performs Line Probing to find the best… |
| 1.3.6.1.4.1.664.5.59.1.3.1.1.10 | ColumnadEShdslProvConstellation | read-write | current | This object sets the constellation size for each SHDSL line. The selected constellation size is rate dependent. 16-TCPAM can only be used for rates ranging fro… |
| 1.3.6.1.4.1.664.5.59.1.3.1.1.11 | ColumnadEShdslProvPowerBackoff | read-write | current | This object sets the power backoff value for each SHDSL line. If 255 is selected, the power backoff will automatically be applied up to 6 dB. Valid values for … |
| 1.3.6.1.4.1.664.5.59.1.3.1.1.12 | ColumnadEShdslProvName | read-write | current | This object sets a display name associated with the selected SHDSL interface. |
| 1.3.6.1.4.1.664.5.59.1.3.1.1.13 | ColumnadEShdslProvSpanPower | read-write | current | Span power. This is usually NOT applicable to a remote/NCTE unit. Usually only applies for CO equipment (e.g. an access module). |
| 1.3.6.1.4.1.664.5.59.1.3.1.1.14 | ColumnadEShdslProvNIUloopback | read-write | current | NIU Loopback enable. May not be applicate for all units. |
| 1.3.6.1.4.1.664.5.59.1.3.1.1.15 | ColumnadEShdslProvConstellationCrossoverRate | read-write | current | This object defines the rate (in bits per second) at which the number of bits per symbol used automatically changes from 3 (16-TCPAM) to 4 (32-TCPAM). When the… |
| 1.3.6.1.4.1.664.5.59.1.3.1.1.16 | ColumnadEShdslProvAnfp100KhzLoss | read-write | current | This object specifies the customer measured loss at 100Khz on the respective SHDSL line. When adEShdslProvLineProbing is set to enableANFP(4) this value sets t… |
| 1.3.6.1.4.1.664.5.59.1.3.1.1.17 | ColumnadEShdslProvAnfpTargetMargin | read-write | current | This object specifies the target SNR margin for a SHDSL line when the ANFP rate mode has been selected. The SNR margin is the difference between the desired SN… |
| 1.3.6.1.4.1.664.5.59.1.3.1.1.18 | ColumnadEShdslProvEmergencyFreeze | read-write | current | This object controls Emergency Freeze operation which provides enhanced immunity to micro interruptions and short duration overvoltage conditions. |
| 1.3.6.1.4.1.664.5.59.1.3.1.1.19 | ColumnadEShdslProvExtendedFixedRateAndConstellation | read-write | current | This object provisions the rate and constellation to be used in Extended Fixed mode. The first octet contains the rate in 64kbps increments (Nx64k). The second… |
| 1.3.6.1.4.1.664.5.59.1.3.1.1.20 | ColumnadEShdslProvExtendedFixedLastError | read-only | current | This object returns the last error encountered during a SET of adEShdslProvExtendedFixedRateAndConstellation. |
| 1.3.6.1.4.1.664.5.59.1.3.1.1.21 | ColumnadEShdslProvAnfp100KhzLossLetter | read-write | current | When adEShdslProvLineProbing is set to enableANFPWorstCase(10) or enableANFPCurrentCond(11) this object sets the maximum rate according to the ANFP spec U (Ult… |
| 1.3.6.1.4.1.664.5.59.1.3.1.1.22 | ColumnadEShdslProvAnfpMaxLineRate | read-write | current | This object configures the maximum transmission rate for the associated SHDSL Line in bits-per-second (bps) when an ANFP training mode is enabled. The maximum … |
| 1.3.6.1.4.1.664.5.59.1.3.1.1.23 | ColumnadEShdslProvSCIAlarmThresh | read-write | current | This object configures the SCI alarm threshold for adEShdslSCIThreshCrossed in seconds. A value of 0 means the alarm is disabled. |
| 1.3.6.1.4.1.664.5.59.1.3.1.1.24 | ColumnadEShdslProvSCIAlarmSeverity | read-write | current | Sets the severity for adEShdslSCIThreshCrossed. Valid options listed below: critical (0) major (1) minor (2) alert (3) info (4) |
| 1.3.6.1.4.1.664.5.59.1.3.2 | TableadEShdslAlarmProvTable | not-accessible | current | This table supports definitions of the alarm configuration of SHDSL lines. |
| 1.3.6.1.4.1.664.5.59.1.3.2.1 | RowadEShdslAlarmProvEntry | not-accessible | current | An entry in the adEShdslAlarmProvTable. |
| 1.3.6.1.4.1.664.5.59.1.3.2.1.1 | ColumnadEShdslAlarmProvLoopAttenThresh | read-write | current | This object configures the loop attenuation alarm threshold. A value of 0 means the alarm is disabled. |
| 1.3.6.1.4.1.664.5.59.1.3.2.1.2 | ColumnadEShdslAlarmProvSNRMarginThresh | read-write | current | This object configures the SNR margin alarm threshold. A value of 0 means the alarm is disabled. |
| 1.3.6.1.4.1.664.5.59.1.3.2.1.3 | ColumnadEShdslAlarmProvESThresh | read-write | current | This object configures the 15-Minute Errored Second alarm threshold. A value of 0 means the alarm is disabled. |
| 1.3.6.1.4.1.664.5.59.1.3.2.1.4 | ColumnadEShdslAlarmProvSESThresh | read-write | current | This object configures the 15-Minute Severely Errored Second alarm threshold. A value of 0 means the alarm is disabled. |
| 1.3.6.1.4.1.664.5.59.1.3.2.1.5 | ColumnadEShdslAlarmProvUASThresh | read-write | current | This object configures the 15-Minute Unavailable Second alarm threshold. A value of 0 means the alarm is disabled. |
| 1.3.6.1.4.1.664.5.59.1.3.2.1.6 | ColumnadEShdslAlarmProvCVCThresh | read-write | current | This object configures the 15-Minute Code Violation Count alarm threshold. A value of 0 means the alarm is disabled. |
| 1.3.6.1.4.1.664.5.59.1.3.2.1.7 | ColumnadEShdslAlarmProvLOSWSThresh | read-write | current | This object configures the 15-Minute Loss of Sync Word Second alarm threshold. A value of 0 means the alarm is disabled. |
| 1.3.6.1.4.1.664.5.59.1.3.2.1.8 | ColumnadEShdslAlarmProvOSThresh | read-write | current | This object configures the 15-Minute Outage Second alarm threshold. A value of 0 means the alarm is disabled. |
| 1.3.6.1.4.1.664.5.59.1.3.2.1.9 | ColumnadEShdslAlarmProvES24HrThresh | read-write | current | This object configures the 24-Hour Errored Second alarm threshold. A value of 0 means the alarm is disabled. |
| 1.3.6.1.4.1.664.5.59.1.3.2.1.10 | ColumnadEShdslAlarmProvSES24HrThresh | read-write | current | This object configures the 24-Hour Severely Errored Second alarm threshold. A value of 0 means the alarm is disabled. |
| 1.3.6.1.4.1.664.5.59.1.3.2.1.11 | ColumnadEShdslAlarmProvUAS24HrThresh | read-write | current | This object configures the 24-Hour Unavailable Second alarm threshold. A value of 0 means the alarm is disabled. |
| 1.3.6.1.4.1.664.5.59.1.3.2.1.12 | ColumnadEShdslAlarmProvCVC24HrThresh | read-write | current | This object configures the 24-Hour Code Violation Count alarm threshold. A value of 0 means the alarm is disabled. |
| 1.3.6.1.4.1.664.5.59.1.3.2.1.13 | ColumnadEShdslAlarmProvLOSWS24HrThresh | read-write | current | This object configures the 24-Hour Loss of Sync Word Second alarm threshold. A value of 0 means the alarm is disabled. |
| 1.3.6.1.4.1.664.5.59.1.3.2.1.14 | ColumnadEShdslAlarmProvOS24HrThresh | read-write | current | This object configures the 24-Hour Outage Second alarm threshold. A value of 0 means the alarm is disabled. |
| 1.3.6.1.4.1.664.5.59.1.3.2.1.15 | ColumnadEShdslAlarmProvRetrains15MinThresh | read-write | current | This object configures the 15 minute alarm threshold for the number of times the specified interface transitions from handshaking to training. A value of 0 mea… |
| 1.3.6.1.4.1.664.5.59.1.3.2.1.16 | ColumnadEShdslAlarmProvHandshakeFailures15MinThresh | read-write | current | This object configures the 15 minute alarm threshold for the number of times a handshake session fails to converge on the specified interface A value of 0 mean… |
| 1.3.6.1.4.1.664.5.59.1.3.2.1.17 | ColumnadEShdslAlarmProvRetrains24HrThresh | read-write | current | This object configures the 24 hour alarm threshold for the number of times the specified interface transitions from handshaking to training. A value of 0 means… |
| 1.3.6.1.4.1.664.5.59.1.3.2.1.18 | ColumnadEShdslAlarmProvHandshakeFailures24HrThresh | read-write | current | This object configures the 24 hour alarm threshold for the number of times a handshake session fails to converge on the specified interface A value of 0 means … |
| 1.3.6.1.4.1.664.5.59.1.3.3 | TableadEShdslTestProvTable | not-accessible | current | This table supports definitions of the test configuration of SHDSL lines. |
| 1.3.6.1.4.1.664.5.59.1.3.3.1 | RowadEShdslTestProvEntry | not-accessible | current | An entry in the adEShdslTestProvTable. |
| 1.3.6.1.4.1.664.5.59.1.3.3.1.1 | ColumnadEShdslTestProvLoopbackTimeout | read-write | current | This object configures the loopback timeout. The timeout is a 12-bit unsigned integer that represents the number of minutes after which the loopback will be re… |
| 1.3.6.1.4.1.664.5.59.1.3.3.1.2 | ColumnadEShdslTestProvEnumeratedLoopbackTimeout | read-write | current | This object configures the loopback timeout. The timeout is selected from the enumerated list. Products that support this method do not support adEShdslTestPro… |
| 1.3.6.1.4.1.664.5.59.1.4 | NodeadEShdslStatus | |||
| 1.3.6.1.4.1.664.5.59.1.4.1 | TableadEShdslStatusTable | not-accessible | current | This table contains entries that report the current status of each point along the SHDSL line. |
| 1.3.6.1.4.1.664.5.59.1.4.1.1 | RowadEShdslStatusEntry | not-accessible | current | An entry in the adEShdslStatusTable. |
| 1.3.6.1.4.1.664.5.59.1.4.1.1.1 | ColumnadEShdslStatusCurrStatus | read-only | current | Indicates the current status of the requested SHDSL interface. |
| 1.3.6.1.4.1.664.5.59.1.4.1.1.2 | ColumnadEShdslStatusCurrLoopAtten | read-only | current | Indicates the current value of the loop attenuation at the requested SHDSL interface. |
| 1.3.6.1.4.1.664.5.59.1.4.1.1.3 | ColumnadEShdslStatusMinLoopAtten | read-only | current | Indicates the minimum value of the loop attenuation since the last reset. |
| 1.3.6.1.4.1.664.5.59.1.4.1.1.4 | ColumnadEShdslStatusMaxLoopAtten | read-only | current | Indicates the maximum value of the loop attenuation since the last reset. |
| 1.3.6.1.4.1.664.5.59.1.4.1.1.5 | ColumnadEShdslStatusCurrSNRMargin | read-only | current | Indicates the current value of the SNR margin at the requested SHDSL interface. |
| 1.3.6.1.4.1.664.5.59.1.4.1.1.6 | ColumnadEShdslStatusMinSNRMargin | read-only | current | Indicates the minimum value of the SNR margin since the last reset. |
| 1.3.6.1.4.1.664.5.59.1.4.1.1.7 | ColumnadEShdslStatusMaxSNRMargin | read-only | current | Indicates the maximum value of the SNR margin since the last reset. |
| 1.3.6.1.4.1.664.5.59.1.4.1.1.8 | ColumnadEShdslStatusES | read-only | current | Indicates the number of Errored Seconds since the last reset. |
| 1.3.6.1.4.1.664.5.59.1.4.1.1.9 | ColumnadEShdslStatusSES | read-only | current | Indicates the number of Severely Errored Seconds since the last reset. |
| 1.3.6.1.4.1.664.5.59.1.4.1.1.10 | ColumnadEShdslStatusUAS | read-only | current | Indicates the number of Unavailable Seconds since the last reset. |
| 1.3.6.1.4.1.664.5.59.1.4.1.1.11 | ColumnadEShdslStatusCVC | read-only | current | Indicates the number of Code Violations since the last reset. |
| 1.3.6.1.4.1.664.5.59.1.4.1.1.12 | ColumnadEShdslStatusLOSWS | read-only | current | Indicates the number of Loss of Sync Word Seconds since the last reset. |
| 1.3.6.1.4.1.664.5.59.1.4.1.1.13 | ColumnadEShdslStatusOS | read-only | current | Indicates the number of Outage Seconds since the last reset. |
| 1.3.6.1.4.1.664.5.59.1.4.1.1.14 | ColumnadEShdslStatusResetStatistics | read-write | current | A SET causes the status information to be reset. A GET returns a 1. |
| 1.3.6.1.4.1.664.5.59.1.4.1.1.15 | ColumnadEShdslStatusMaxAttainableRate | read-only | current | Indicates the maximum attainable line rate for this interface in bps. |
| 1.3.6.1.4.1.664.5.59.1.4.1.1.16 | ColumnadEShdslStatusUpstreamPBO | read-only | current | Indicates the value of the power backoff (in dB) in the upstream direction. (i.e. the closest SHDSL network interface to the endpoint selected. |
| 1.3.6.1.4.1.664.5.59.1.4.1.1.17 | ColumnadEShdslStatusDownstreamPBO | read-only | current | Indicates the value of the power backoff (in dB) in the downstream direction. (i.e. the closest SHDSL customer interface to the endpoint selected. |
| 1.3.6.1.4.1.664.5.59.1.4.1.1.18 | ColumnadEShdslStatusCurrRate | read-only | current | This object returns the currently configured rate for the associated SHDSL Line in bits-per-second (bps). This represents the actual rate the line is trained a… |
| 1.3.6.1.4.1.664.5.59.1.4.1.1.19 | ColumnadEShdslStatusRetrains | read-only | current | Indicates the number of times, since last reset, that the specified interface has transitioned from handshaking to training. |
| 1.3.6.1.4.1.664.5.59.1.4.1.1.20 | ColumnadEShdslStatusHandshakeFailures | read-only | current | Indicates the number of times, since last reset, that a handshake session failed to converge on the specified interface |
| 1.3.6.1.4.1.664.5.59.1.4.1.1.21 | ColumnadEShdslStatusCurrSNRMarginCurrTrain | read-only | current | Indicates the current value of the SNR margin at the requested SHDSL interface. |
| 1.3.6.1.4.1.664.5.59.1.4.1.1.22 | ColumnadEShdslStatusMinSNRMarginCurrTrain | read-only | current | Indicates the minimum value of the SNR margin observed since the last retrain. |
| 1.3.6.1.4.1.664.5.59.1.4.1.1.23 | ColumnadEShdslStatusMaxSNRMarginCurrTrain | read-only | current | Indicates the maximum value of the SNR margin observed since the last retrain. |
| 1.3.6.1.4.1.664.5.59.1.4.1.1.24 | ColumnadEShdslStatusMinSNRMarginPrevTrain | read-only | current | Indicates the minimum value of the SNR margin observed before the last retrain. |
| 1.3.6.1.4.1.664.5.59.1.4.1.1.25 | ColumnadEShdslStatusMaxSNRMarginPrevTrain | read-only | current | Indicates the maximum value of the SNR margin observed before the last retrain. |
| 1.3.6.1.4.1.664.5.59.1.4.1.1.26 | ColumnadEShdslStatusPhysicalLinkLabel | read-only | current | Returns the label used to physically identify the specified side of an element. For example, SHDSL repeaters have an A side and a B side. For elements without … |
| 1.3.6.1.4.1.664.5.59.1.4.2 | TableadEShdslStatusInfoTable | not-accessible | current | This table contains entries that report the current status of each point along the SHDSL line. |
| 1.3.6.1.4.1.664.5.59.1.4.2.1 | RowadEShdslStatusInfoEntry | not-accessible | current | An entry in the adEShdslStatusInfoTable. |
| 1.3.6.1.4.1.664.5.59.1.4.2.1.1 | ColumnadEShdslStatusInfoRepeaterNumber | read-only | current | Number of repeaters/regenerators detected on this interface |
| 1.3.6.1.4.1.664.5.59.1.4.2.1.2 | ColumnadEShdslStatusInfoPairReversal | read-only | current | A stream of bytes representing the pair reversal status for each span. The MSB is for span 1 (e.g. from the H4TUC to the H4TUR/H4RU1), the next byte is for spa… |
| 1.3.6.1.4.1.664.5.59.1.4.2.1.3 | ColumnadEShdslStatusInfoLoopAlarmStatus | read-only | current | A stream of byte codes identifying the current alarm status of each DSL loop point. For SHDSL:The bytes are in order from the MSB: LTU L1, LTU L2, NTU L1, NTU … |
| 1.3.6.1.4.1.664.5.59.1.4.2.1.4 | ColumnadEShdslStatusInfoTopology | read-only | current | A stream of bytes used to represent the topology of a given circuit. The format is show below: Version 1 Octet Description Common 0 Version number of this OID.… |
| 1.3.6.1.4.1.664.5.59.1.4.3 | TableadEShdslStatusIfTable | not-accessible | current | This table contains entries that report the current status of each SHDSL interface. |
| 1.3.6.1.4.1.664.5.59.1.4.3.1 | RowadEShdslStatusIfEntry | not-accessible | current | An entry in the adEShdslStatusIfTable. |
| 1.3.6.1.4.1.664.5.59.1.4.3.1.1 | ColumnadEShdslStatusIfTrainingMode | read-only | current | Indicates the mode of the SHDSL interface. Only valid for products that support direct MIB access. |
| 1.3.6.1.4.1.664.5.59.1.5 | NodeadEShdslTest | |||
| 1.3.6.1.4.1.664.5.59.1.5.1 | TableadEShdslTestTable | not-accessible | current | This table contains entries that allow the user to run tests at different points along the SHDSL line. |
| 1.3.6.1.4.1.664.5.59.1.5.1.1 | RowadEShdslTestEntry | not-accessible | current | An entry in the adEShdslTestTable. |
| 1.3.6.1.4.1.664.5.59.1.5.1.1.1 | ColumnadEShdslTestLoopback | read-write | current | Controls enabling/disabling loopbacks along each SHDSL interface |
| 1.3.6.1.4.1.664.5.59.1.5.1.1.2 | ColumnadEShdslTestLoopdownAll | read-write | current | This object is a command to loopdown all the interfaces in the circuit when set. This applies to all interfaces currently looped back. There is no significance… |
| 1.3.6.1.4.1.664.5.59.1.5.1.1.3 | ColumnadEShdslTestinitMinMax | read-write | current | Reset Min/Max characteristics of the Loops. Always returns 1 on get. |
| 1.3.6.1.4.1.664.5.59.1.5.2 | TableadEShdslTestRepeaterPoweringTable | not-accessible | current | This table contains entries that allow the user control the powering sequence of SHDSL repeaters. |
| 1.3.6.1.4.1.664.5.59.1.5.2.1 | RowadEShdslTestRepeaterPoweringEntry | not-accessible | current | An entry in the adEShdslTestRepeaterPoweringTable. |
| 1.3.6.1.4.1.664.5.59.1.5.2.1.1 | ColumnadEShdslTestRepeaterPoweringState | read-write | current | Determines the method by which the repeaters provide power. The default mode is normal(1) where the repeaters read their hardware dip switches to determine whe… |
| 1.3.6.1.4.1.664.5.59.1.5.2.1.2 | ColumnadEShdslTestRepeaterPoweringNumRepeaters | read-write | current | The number of repeaters to power. Only valid if adEShdslTestRepeaterPoweringState is set to manual(2). |
| 1.3.6.1.4.1.664.5.59.1.5.2.1.3 | ColumnadEShdslTestRepeaterPoweringTimeout | read-write | current | The amount of time after which adEShdslTestRepeaterPoweringState will be set back to normal(1). A value of 0 means there is no timeout and the state will not r… |
| 1.3.6.1.4.1.664.5.59.1.5.2.1.4 | ColumnadEShdslTestRepeaterPoweringTimeRemaining | read-only | current | The amount of time remaining before adEShdslTestRepeaterPoweringState will be set back to normal(1). Only valid if adEShdslTestRepeaterPoweringTimeout is non-z… |
| 1.3.6.1.4.1.664.5.59.1.5.2.1.5 | ColumnadEShdslTestRepeaterPoweringSRU1Discovered | read-only | current | Returns true(1) if SRU1 is present. Returns false(2) otherwise. Only valid if adEShdslTestRepeaterPoweringState is set to manual(2). |
| 1.3.6.1.4.1.664.5.59.1.5.2.1.6 | ColumnadEShdslTestRepeaterPoweringSRU2Discovered | read-only | current | Returns true(1) if SRU2 is present. Returns false(2) otherwise. Only valid if adEShdslTestRepeaterPoweringState is set to manual(2). |
| 1.3.6.1.4.1.664.5.59.1.5.2.1.7 | ColumnadEShdslTestRepeaterPoweringSRU3Discovered | read-only | current | Returns true(1) if SRU3 is present. Returns false(2) otherwise. Only valid if adEShdslTestRepeaterPoweringState is set to manual(2). |
| 1.3.6.1.4.1.664.5.59.1.5.2.1.8 | ColumnadEShdslTestRepeaterPoweringSRU4Discovered | read-only | current | Returns true(1) if SRU4 is present. Returns false(2) otherwise. Only valid if adEShdslTestRepeaterPoweringState is set to manual(2). |
| 1.3.6.1.4.1.664.5.59.1.5.2.1.9 | ColumnadEShdslTestRepeaterPoweringShortDetected | read-only | current | Returns the location of a detected powering short. This will be the repeater at the end of the powered span. Returns none(0) if no short has been detected. Onl… |
| 1.3.6.1.4.1.664.5.59.1.5.2.1.10 | ColumnadEShdslTestRepeaterPoweringGroundFaultDetected | read-only | current | Returns the location of a detected powering ground fault. This will be the repeater at the end of the powered span. Returns none(0) if no short has been detect… |
| 1.3.6.1.4.1.664.5.59.1.5.2.1.11 | ColumnadEShdslTestRepeaterPoweringLastErrorString | read-only | current | Text string describing the last error encountered when attempting to SET one of the entries in this table. |
| 1.3.6.1.4.1.664.5.59.1.5.3 | TableadEShdslTestLoopLocatorLastErrorTable | not-accessible | current | This table contains the last error message generated by operations on the entries in adEShdslTestLoopLocatorTable. |
| 1.3.6.1.4.1.664.5.59.1.5.3.1 | RowadEShdslTestLoopLocatorLastErrorEntry | not-accessible | current | An entry in the adEShdslTestLoopLocatorLastErrorTable. |
| 1.3.6.1.4.1.664.5.59.1.5.3.1.1 | ColumnadEShdslTestLoopLocatorLastErrorString | read-only | current | Text string describing the last error encountered when attempting to SET one of the entries in adEShdslTestLoopLocatorTable. |
| 1.3.6.1.4.1.664.5.59.1.5.4 | TableadEShdslTestLoopLocatorTable | not-accessible | current | This table contains entries that allows the user to inject modulated noise to identify a particular loop with a handset. |
| 1.3.6.1.4.1.664.5.59.1.5.4.1 | RowadEShdslTestLoopLocatorEntry | not-accessible | current | An entry in the adEShdslTestLoopLocatorTable. |
| 1.3.6.1.4.1.664.5.59.1.5.4.1.1 | ColumnadEShdslTestLoopLocatorState | read-write | current | Activates the loop locator test, injecting modulated noise onto the specified loop. The default mode is disabled(1). This is primarily used to diagnose wiring … |
| 1.3.6.1.4.1.664.5.59.1.5.4.1.2 | ColumnadEShdslTestLoopLocatorTimeout | read-write | current | The amount of time after which adEShdslTestLoopLocatorState will be set back to disabled(1). A value of 0 means there is no timeout and the state will not reve… |
| 1.3.6.1.4.1.664.5.59.1.5.4.1.3 | ColumnadEShdslTestLoopLocatorTimeRemaining | read-only | current | The amount of time remaining before adEShdslTestLoopLocatorState will be set back to disabled(1). Only valid if adEShdslTestLoopLocatorTimeout is non-zero and … |
| 1.3.6.1.4.1.664.5.59.1.6 | NodeadEShdslPerformance | |||
| 1.3.6.1.4.1.664.5.59.1.6.1 | TableadEShdslPerfCurrTable | not-accessible | current | This table contains entries that allow the user to retrieve the current performance history values at different points along the SHDSL line. |
| 1.3.6.1.4.1.664.5.59.1.6.1.1 | RowadEShdslPerfCurrEntry | not-accessible | current | An entry in the adEShdslPerfCurrTable. |
| 1.3.6.1.4.1.664.5.59.1.6.1.1.1 | ColumnadEShdslPerfCurr15MinES | read-only | current | Indicates the number of Errored Seconds in the current 15 minute interval. |
| 1.3.6.1.4.1.664.5.59.1.6.1.1.2 | ColumnadEShdslPerfCurr15MinSES | read-only | current | Indicates the number of Severely Errored Seconds in the current 15 minute interval. |
| 1.3.6.1.4.1.664.5.59.1.6.1.1.3 | ColumnadEShdslPerfCurr15MinUAS | read-only | current | Indicates the number of Unavailable Seconds in the current 15 minute interval. |
| 1.3.6.1.4.1.664.5.59.1.6.1.1.4 | ColumnadEShdslPerfCurr15MinCVC | read-only | current | Indicates the number of Code Violations in the current 15 minute interval. |
| 1.3.6.1.4.1.664.5.59.1.6.1.1.5 | ColumnadEShdslPerfCurr15MinLOSWS | read-only | current | Indicates the number of Loss of Sync Word Seconds in the current 15 minute interval. |
| 1.3.6.1.4.1.664.5.59.1.6.1.1.6 | ColumnadEShdslPerfCurr15MinOS | read-only | current | Indicates the number of Outage Seconds in the current 15 minute interval. |
| 1.3.6.1.4.1.664.5.59.1.6.1.1.7 | ColumnadEShdslPerfCurr24HrES | read-only | current | Indicates the number of Errored Seconds in the current 24 hour interval. |
| 1.3.6.1.4.1.664.5.59.1.6.1.1.8 | ColumnadEShdslPerfCurr24HrSES | read-only | current | Indicates the number of Severely Errored Seconds in the current 24 hour interval. |
| 1.3.6.1.4.1.664.5.59.1.6.1.1.9 | ColumnadEShdslPerfCurr24HrUAS | read-only | current | Indicates the number of Unavailable Seconds in the current 24 hour interval. |
| 1.3.6.1.4.1.664.5.59.1.6.1.1.10 | ColumnadEShdslPerfCurr24HrCVC | read-only | current | Indicates the number of Code Violations in the current 24 hour interval. |
| 1.3.6.1.4.1.664.5.59.1.6.1.1.11 | ColumnadEShdslPerfCurr24HrLOSWS | read-only | current | Indicates the number of Loss of Sync Word Seconds in the current 24 hour interval. |
| 1.3.6.1.4.1.664.5.59.1.6.1.1.12 | ColumnadEShdslPerfCurr24HrOS | read-only | current | Indicates the number of Outage Seconds in the current 24 hour interval. |
| 1.3.6.1.4.1.664.5.59.1.6.1.1.13 | ColumnadEShdslPerf15MinValidIntervals | read-only | current | The number of valid 15-Minute intervals. |
| 1.3.6.1.4.1.664.5.59.1.6.1.1.14 | ColumnadEShdslPerf24HrValidIntervals | read-only | current | The number of valid 24-Hour intervals. |
| 1.3.6.1.4.1.664.5.59.1.6.1.1.15 | ColumnadEShdslPerfCurr15MinRetrains | read-only | current | Indicates the number of times in the current 15 minute interval that the specified interface has transitioned from handshaking to training. |
| 1.3.6.1.4.1.664.5.59.1.6.1.1.16 | ColumnadEShdslPerfCurr15MinHandshakeFailures | read-only | current | Indicates the number of times in the current 15 minute interval that a handshake session failed to converge on the specified interface |
| 1.3.6.1.4.1.664.5.59.1.6.1.1.17 | ColumnadEShdslPerfCurr24HrRetrains | read-only | current | Indicates the number of times in the current 24 hour interval that the specified interface has transitioned from handshaking to training. |
| 1.3.6.1.4.1.664.5.59.1.6.1.1.18 | ColumnadEShdslPerfCurr24HrHandshakeFailures | read-only | current | Indicates the number of times in the current 24 hour interval that a handshake session failed to converge on the specified interface |
| 1.3.6.1.4.1.664.5.59.1.6.1.1.19 | ColumnadEShdslPerfCurr15MinMinSNRMargin | read-only | current | Indicates the minimum SNR margin observed in the current 15 minute interval. |
| 1.3.6.1.4.1.664.5.59.1.6.1.1.20 | ColumnadEShdslPerfCurr15MinMaxSNRMargin | read-only | current | Indicates the maximum SNR margin observed in the current 15 minute interval. |
| 1.3.6.1.4.1.664.5.59.1.6.1.1.21 | ColumnadEShdslPerfCurr24HrMinSNRMargin | read-only | current | Indicates the minimum SNR margin observed in the current 24 hour interval. |
| 1.3.6.1.4.1.664.5.59.1.6.1.1.22 | ColumnadEShdslPerfCurr24HrMaxSNRMargin | read-only | current | Indicates the maximum SNR margin observed in the current 24 hour interval. |
| 1.3.6.1.4.1.664.5.59.1.6.2 | TableadEShdslPerfPriorTable | not-accessible | current | This table contains entries that allow the user to retrieve the prior performance history values at different points along the SHDSL line. |
| 1.3.6.1.4.1.664.5.59.1.6.2.1 | RowadEShdslPerfPriorEntry | not-accessible | current | An entry in the adEShdslPerfPriorTable. |
| 1.3.6.1.4.1.664.5.59.1.6.2.1.1 | ColumnadEShdslPerfPrior15MinES | read-only | current | Indicates the number of Errored Seconds in the prior 15 minute interval. |
| 1.3.6.1.4.1.664.5.59.1.6.2.1.2 | ColumnadEShdslPerfPrior15MinSES | read-only | current | Indicates the number of Severely Errored Seconds in the prior 15 minute interval. |
| 1.3.6.1.4.1.664.5.59.1.6.2.1.3 | ColumnadEShdslPerfPrior15MinUAS | read-only | current | Indicates the number of Unavailable Seconds in the prior 15 minute interval. |
| 1.3.6.1.4.1.664.5.59.1.6.2.1.4 | ColumnadEShdslPerfPrior15MinCVC | read-only | current | Indicates the number of Code Violations in the prior 15 minute interval. |
| 1.3.6.1.4.1.664.5.59.1.6.2.1.5 | ColumnadEShdslPerfPrior15MinLOSWS | read-only | current | Indicates the number of Loss of Sync Word Seconds in the prior 15 minute interval. |
| 1.3.6.1.4.1.664.5.59.1.6.2.1.6 | ColumnadEShdslPerfPrior15MinOS | read-only | current | Indicates the number of Outage Seconds in the prior 15 minute interval. |
| 1.3.6.1.4.1.664.5.59.1.6.2.1.7 | ColumnadEShdslPerfPrior24HrES | read-only | current | Indicates the number of Errored Seconds in the prior 24 hour interval. |
| 1.3.6.1.4.1.664.5.59.1.6.2.1.8 | ColumnadEShdslPerfPrior24HrSES | read-only | current | Indicates the number of Severely Errored Seconds in the prior 24 hour interval. |
| 1.3.6.1.4.1.664.5.59.1.6.2.1.9 | ColumnadEShdslPerfPrior24HrUAS | read-only | current | Indicates the number of Unavailable Seconds in the prior 24 hour interval. |
| 1.3.6.1.4.1.664.5.59.1.6.2.1.10 | ColumnadEShdslPerfPrior24HrCVC | read-only | current | Indicates the number of Code Violations in the prior 24 hour interval. |
| 1.3.6.1.4.1.664.5.59.1.6.2.1.11 | ColumnadEShdslPerfPrior24HrLOSWS | read-only | current | Indicates the number of Loss of Sync Word Seconds in the prior 24 hour interval. |
| 1.3.6.1.4.1.664.5.59.1.6.2.1.12 | ColumnadEShdslPerfPrior24HrOS | read-only | current | Indicates the number of Outage Seconds in the prior 24 hour interval. |
| 1.3.6.1.4.1.664.5.59.1.6.3 | TableadEShdslPerfResetTable | not-accessible | current | This table contains entries that allow the user to reset the performance history values at different points along the SHDSL line. |
| 1.3.6.1.4.1.664.5.59.1.6.3.1 | RowadEShdslPerfResetEntry | not-accessible | current | An entry in the adEShdslPerfResetTable. |
| 1.3.6.1.4.1.664.5.59.1.6.3.1.1 | ColumnadEShdslPerfReset | read-write | current | Resets the performance history values on the selected interface. |
| 1.3.6.1.4.1.664.5.59.1.6.4 | TableadEShdslPerf15MinIntTable | not-accessible | current | This table contains entries that allow the user to retrieve the 15 minute performance history values at different points along the SHDSL line. |
| 1.3.6.1.4.1.664.5.59.1.6.4.1 | RowadEShdslPerf15MinIntEntry | not-accessible | current | An entry in the adEShdslPerf15MinIntTable. |
| 1.3.6.1.4.1.664.5.59.1.6.4.1.1 | ColumnadEShdslPerf15MinIntNumber | read-only | current | 15-minute performance interval. Interval 1 represents the most recent previous interval. Interval 96 represents 24 hours ago. Intervals 2 through 96 are option… |
| 1.3.6.1.4.1.664.5.59.1.6.4.1.2 | ColumnadEShdslPerf15MinIntES | read-only | current | Indicates the number of Errored Seconds in the selected 15 minute interval. |
| 1.3.6.1.4.1.664.5.59.1.6.4.1.3 | ColumnadEShdslPerf15MinIntSES | read-only | current | Indicates the number of Severely Errored Seconds in the selected 15 minute interval. |
| 1.3.6.1.4.1.664.5.59.1.6.4.1.4 | ColumnadEShdslPerf15MinIntUAS | read-only | current | Indicates the number of Unavailable Seconds in the selected 15 minute interval. |
| 1.3.6.1.4.1.664.5.59.1.6.4.1.5 | ColumnadEShdslPerf15MinIntCVC | read-only | current | Indicates the number of Code Violations in the selected 15 minute interval. |
| 1.3.6.1.4.1.664.5.59.1.6.4.1.6 | ColumnadEShdslPerf15MinIntLOSWS | read-only | current | Indicates the number of Loss of Sync Word Seconds in the selected 15 minute interval. |
| 1.3.6.1.4.1.664.5.59.1.6.4.1.7 | ColumnadEShdslPerf15MinIntOS | read-only | current | Indicates the number of Outage Seconds in the selected 15 minute interval. |
| 1.3.6.1.4.1.664.5.59.1.6.4.1.8 | ColumnadEShdslPerf15MinIntRetrains | read-only | current | Indicates the number of times in the selected 15 minute interval that the specified interface has transitioned from handshaking to training. |
| 1.3.6.1.4.1.664.5.59.1.6.4.1.9 | ColumnadEShdslPerf15MinIntHandshakeFailures | read-only | current | Indicates the number of times in the selected 15 minute interval that a handshake session failed to converge on the specified interface |
| 1.3.6.1.4.1.664.5.59.1.6.4.1.10 | ColumnadEShdslPerf15MinIntMinSNRMargin | read-only | current | Indicates the minimum SNR margin observed in the specified 15 minute interval. |
| 1.3.6.1.4.1.664.5.59.1.6.4.1.11 | ColumnadEShdslPerf15MinIntMaxSNRMargin | read-only | current | Indicates the maximum SNR margin observed in the specified 15 minute interval. |
| 1.3.6.1.4.1.664.5.59.1.6.5 | TableadEShdslPerf24HrIntTable | not-accessible | current | This table contains entries that allow the user to retrieve the 24 hour performance history values at different points along the SHDSL line. |
| 1.3.6.1.4.1.664.5.59.1.6.5.1 | RowadEShdslPerf24HrIntEntry | not-accessible | current | An entry in the adEShdslPerf24HrIntTable. |
| 1.3.6.1.4.1.664.5.59.1.6.5.1.1 | ColumnadEShdslPerf24HrIntNumber | read-only | current | 24-hour performance interval. Interval 1 represents the most recent previous interval. Interval 7 represents 7 days ago. Intervals 2 through 7 are optional. Al… |
| 1.3.6.1.4.1.664.5.59.1.6.5.1.2 | ColumnadEShdslPerf24HrIntES | read-only | current | Indicates the number of Errored Seconds in the selected 24 hour interval. |
| 1.3.6.1.4.1.664.5.59.1.6.5.1.3 | ColumnadEShdslPerf24HrIntSES | read-only | current | Indicates the number of Severely Errored Seconds in the selected 24 hour interval. |
| 1.3.6.1.4.1.664.5.59.1.6.5.1.4 | ColumnadEShdslPerf24HrIntUAS | read-only | current | Indicates the number of Unavailable Seconds in the selected 24 hour interval. |
| 1.3.6.1.4.1.664.5.59.1.6.5.1.5 | ColumnadEShdslPerf24HrIntCVC | read-only | current | Indicates the number of Code Violations in the selected 24 hour interval. |
| 1.3.6.1.4.1.664.5.59.1.6.5.1.6 | ColumnadEShdslPerf24HrIntLOSWS | read-only | current | Indicates the number of Loss of Sync Word Seconds in the selected 24 hour interval. |
| 1.3.6.1.4.1.664.5.59.1.6.5.1.7 | ColumnadEShdslPerf24HrIntOS | read-only | current | Indicates the number of Outage Seconds in the selected 24 hour interval. |
| 1.3.6.1.4.1.664.5.59.1.6.5.1.8 | ColumnadEShdslPerf24HrIntRetrains | read-only | current | Indicates the number of times in the selected 24 hour interval that the specified interface has transitioned from handshaking to training. |
| 1.3.6.1.4.1.664.5.59.1.6.5.1.9 | ColumnadEShdslPerf24HrIntHandshakeFailures | read-only | current | Indicates the number of times in the selected 24 hour interval that a handshake session failed to converge on the specified interface |
| 1.3.6.1.4.1.664.5.59.1.6.5.1.10 | ColumnadEShdslPerf24HrIntMinSNRMargin | read-only | current | Indicates the minimum SNR margin observed in the specified 24 hour interval. |
| 1.3.6.1.4.1.664.5.59.1.6.5.1.11 | ColumnadEShdslPerf24HrIntMaxSNRMargin | read-only | current | Indicates the maximum SNR margin observed in the specified 24 hour interval. |
| 1.3.6.1.4.1.664.5.59.1.6.6 | TableadEShdslPerfPortResetTable | not-accessible | current | This table contains entries that allow the user to reset the performance history values for each SHDSL port. |
| 1.3.6.1.4.1.664.5.59.1.6.6.1 | RowadEShdslPerfPortResetEntry | not-accessible | current | An entry in the adEShdslPerfPortResetTable. |
| 1.3.6.1.4.1.664.5.59.1.6.6.1.1 | ColumnadEShdslPerfPortReset | read-write | current | Resets the performance history values for all interfaces connected to the selected port. |
| 1.3.6.1.4.1.664.5.59.1.7 | NodeadEShdslSpliceDetection | |||
| 1.3.6.1.4.1.664.5.59.1.7.1 | TableadEShdslSpliceDetectionTable | not-accessible | current | This table contains entries that allow the user to retrieve the splice detection data. |
| 1.3.6.1.4.1.664.5.59.1.7.1.1 | RowadEShdslSpliceDetectionEntry | not-accessible | current | An entry in the adEShdslSpliceDetectionTable. |
| 1.3.6.1.4.1.664.5.59.1.7.1.1.1 | ColumnadEShdslSpliceDetectionSummary | read-only | current | The splice detection summary for this endpoint. A series of items in the following format: STR0.STR1.STR2 ... STR14 representing the daily splice detection sum… |
| 1.3.6.1.4.1.664.5.59.1.7.1.1.2 | ColumnadEShdslSpliceCounts | read-only | current | A series of numbers (0-99) in the following format: N0.N1.N3 ... N17 These values represent the splice detection histogram values for the corresponding distanc… |
| 1.3.6.1.4.1.664.5.59.1.7.1.1.3 | ColumnadEShdslSpliceDistances | read-only | current | A series of distances in the following format: D0.D1.D3 ... D17 These values represent the distances corresponding to each bucket in the splice detection histo… |
| 1.3.6.1.4.1.664.5.59.1.7.1.1.4 | ColumnadEShdslSpliceRestart | read-write | current | Restarts the splice detection on the selected interface. This will cause all 24 hour counts for this interface to be cleared. |
| 1.3.6.1.4.1.664.5.59.1.7.1.1.5 | ColumnadEShdslSpliceDistanceType | read-write | current | Sets the unit of measurement used when returning the values for adEShdslSpliceDistances. This value is set globally for the unit and will return the same value… |
| 1.3.6.1.4.1.664.5.59.1.7.1.1.6 | ColumnadEShdslSpliceRate | read-only | current | A last trained rate during the current interval. The value returned is the rate in 64kbps increments (N x 64k). |
| 1.3.6.1.4.1.664.5.59.1.7.1.1.7 | ColumnadEShdslSpliceBadSpliceDetected | read-only | current | Returns true if a bad splice has been detected on the specified interface. Returns false otherwise. |
| 1.3.6.1.4.1.664.5.59.1.7.2 | TableadEShdslSpliceDet24HrIntTable | not-accessible | current | This table contains entries that allow the user to retrieve 24 hour splice detection historical interval data. |
| 1.3.6.1.4.1.664.5.59.1.7.2.1 | RowadEShdslSpliceDet24HrIntEntry | not-accessible | current | An entry in the adEShdslSpliceDet24HrIntTable. |
| 1.3.6.1.4.1.664.5.59.1.7.2.1.1 | ColumnadEShdslSpliceDet24HrIntNumber | read-only | current | 24-hour splice detect interval. Interval 1 represents the most recent previous interval. Interval 7 represents 7 days ago. Intervals 2 through 7 are optional. |
| 1.3.6.1.4.1.664.5.59.1.7.2.1.2 | ColumnadEShdslSplice24HrIntCounts | read-only | current | A series of numbers (0-99) in the following format: N0.N1.N3 ... N17 These values represent the splice detection histogram values for the corresponding distanc… |
| 1.3.6.1.4.1.664.5.59.1.7.2.1.3 | ColumnadEShdslSplice24HrIntDistances | read-only | current | A series of distances in the following format: D0.D1.D3 ... D17 These values represent the distances corresponding to each bucket in the splice detection histo… |
| 1.3.6.1.4.1.664.5.59.1.7.2.1.4 | ColumnadEShdslSplice24HrIntRate | read-only | current | A last trained rate during the specified interval. The value returned is the rate in 64kbps increments (N x 64k). |
| 1.3.6.1.4.1.664.5.59.1.7.3 | TableadEShdslSpliceDet15MinCurrTable | not-accessible | current | This table contains entries that allow the user to retrieve 15 minute splice detection current interval data. |
| 1.3.6.1.4.1.664.5.59.1.7.3.1 | RowadEShdslSpliceDet15MinCurrEntry | not-accessible | current | An entry in the adEShdslSpliceDet15MinCurrTable. |
| 1.3.6.1.4.1.664.5.59.1.7.3.1.1 | ColumnadEShdslSplice15MinCurrCounts | read-only | current | A series of numbers (0-99) in the following format: N0.N1.N3 ... N17 These values represent the splice detection histogram values for the corresponding distanc… |
| 1.3.6.1.4.1.664.5.59.1.7.3.1.2 | ColumnadEShdslSplice15MinCurrDistances | read-only | current | A series of distances in the following format: D0.D1.D3 ... D17 These values represent the distances corresponding to each bucket in the splice detection histo… |
| 1.3.6.1.4.1.664.5.59.1.7.3.1.3 | ColumnadEShdslSplice15MinCurrRate | read-only | current | A last trained rate during the current interval. The value returned is the rate in 64kbps increments (N x 64k). |
| 1.3.6.1.4.1.664.5.59.1.7.4 | TableadEShdslSpliceDet15MinIntTable | not-accessible | current | This table contains entries that allow the user to retrieve 15 minute splice detection historical interval data. |
| 1.3.6.1.4.1.664.5.59.1.7.4.1 | RowadEShdslSpliceDet15MinIntEntry | not-accessible | current | An entry in the adEShdslSpliceDet15MinIntTable. |
| 1.3.6.1.4.1.664.5.59.1.7.4.1.1 | ColumnadEShdslSpliceDet15MinIntNumber | read-only | current | 15 minute splice detect interval. Interval 1 represents the most recent previous interval. |
| 1.3.6.1.4.1.664.5.59.1.7.4.1.2 | ColumnadEShdslSplice15MinIntCounts | read-only | current | A series of numbers (0-99) in the following format: N0.N1.N3 ... N17 These values represent the splice detection histogram values for the corresponding distanc… |
| 1.3.6.1.4.1.664.5.59.1.7.4.1.3 | ColumnadEShdslSplice15MinIntDistances | read-only | current | A series of distances in the following format: D0.D1.D3 ... D17 These values represent the distances corresponding to each bucket in the splice detection histo… |
| 1.3.6.1.4.1.664.5.59.1.7.4.1.4 | ColumnadEShdslSplice15MinIntRate | read-only | current | A last trained rate during the specified interval. The value returned is the rate in 64kbps increments (N x 64k). |
| 1.3.6.1.4.1.664.5.59.1.8 | NodeadEShdslMibConformance | |||
| 1.3.6.1.4.1.664.5.59.1.8.1 | NodeadEShdslMibGroups | |||
| 1.3.6.1.4.1.664.5.59.1.8.1.1 | GroupadGenEShdslIndexGroup | current | These objects provide support for SHDSL indexing. | |
| 1.3.6.1.4.1.664.5.59.1.8.1.2 | GroupadGenEShdslInvGroup | current | These objects provide support for SHDSL inventory retrieval. | |
| 1.3.6.1.4.1.664.5.59.1.8.1.3 | GroupadGenEShdslProvGroup | current | These objects provide support for SHDSL provisioning. | |
| 1.3.6.1.4.1.664.5.59.1.8.1.4 | GroupadGenEShdslStatusGroup | current | These objects provide support for SHDSL status retrieval. | |
| 1.3.6.1.4.1.664.5.59.1.8.1.5 | GroupadGenEShdslTestGroup | current | These objects provide access for the testing of SHDSL links | |
| 1.3.6.1.4.1.664.5.59.1.8.1.6 | GroupadGenEShdslCurr15MinPerfGroup | current | These objects provide support for the reporting of the current 15 minute interval of PM data. | |
| 1.3.6.1.4.1.664.5.59.1.8.1.7 | GroupadGenEShdslCurr24HrPerfGroup | current | These objects provide support for the reporting of the current 24 hour interval of PM data. | |
| 1.3.6.1.4.1.664.5.59.1.8.1.8 | GroupadGenEShdslPrior15MinPerfGroup | current | These objects provide support for the reporting of the prior 15 minute interval of PM data. | |
| 1.3.6.1.4.1.664.5.59.1.8.1.9 | GroupadGenEShdslPrior24HrPerfGroup | current | These objects provide support for the reporting of the prior 24 hour interval of PM data. | |
| 1.3.6.1.4.1.664.5.59.1.8.1.10 | GroupadGenEShdslInt15MinPerfGroup | current | These objects provide support for the reporting of the selected 15 minute interval of PM data. | |
| 1.3.6.1.4.1.664.5.59.1.8.1.11 | GroupadGenEShdslInt24HrPerfGroup | current | These objects provide support for the reporting of the selected 24 hour interval of PM data. | |
| 1.3.6.1.4.1.664.5.59.1.8.1.12 | GroupadGenEShdslSpliceGroup | current | These objects provide support for bad splice detection. | |
| 1.3.6.1.4.1.664.5.59.1.8.1.13 | GroupadGenEShdslEventGroup | current | GenEShdsl Notification Group | |
| 1.3.6.1.4.1.664.5.59.1.8.1.14 | GroupadGenEShdslInt24HrSpliceDetGroup | current | These objects provide support for bad splice detection for the selected 24 hour interval. | |
| 1.3.6.1.4.1.664.5.59.1.8.1.15 | GroupadGenEShdslPerfResetGroup | current | These objects provide support for resetting of performance history. | |
| 1.3.6.1.4.1.664.5.59.1.10 | NodeadEShdslAlarmsPrefix | |||
| 1.3.6.1.4.1.664.5.59.1.10.0 | NodeadEShdslAlarms | |||
| 1.3.6.1.4.1.664.5.59.1.10.0.2 | NotificationadEShdslLossofSignalAlmCLR | current | Loss of Signal Alarm | |
| 1.3.6.1.4.1.664.5.59.1.10.0.3 | NotificationadEShdslLossofSignalAlmACT | current | Loss of Signal Alarm | |
| 1.3.6.1.4.1.664.5.59.1.10.0.4 | NotificationadEShdslLTULossofSyncWordAlmCLR | current | LTU Loss of Sync Word Alarm | |
| 1.3.6.1.4.1.664.5.59.1.10.0.5 | NotificationadEShdslLTULossofSyncWordAlmACT | current | LTU Loss of Sync Word Alarm | |
| 1.3.6.1.4.1.664.5.59.1.10.0.6 | NotificationadEShdslLTUCRCErrorAlmCLR | current | LTU CRC Error | |
| 1.3.6.1.4.1.664.5.59.1.10.0.7 | NotificationadEShdslLTUCRCErrorAlmACT | current | LTU CRC Error | |
| 1.3.6.1.4.1.664.5.59.1.10.0.8 | NotificationadEShdslLTUSNRMarginAlmCLR | current | LTU SNR Margin Alarm | |
| 1.3.6.1.4.1.664.5.59.1.10.0.9 | NotificationadEShdslLTUSNRMarginAlmACT | current | LTU SNR Margin Alarm | |
| 1.3.6.1.4.1.664.5.59.1.10.0.10 | NotificationadEShdslLTULoopAttenAlmCLR | current | LTU Loop Attenuation Alarm | |
| 1.3.6.1.4.1.664.5.59.1.10.0.11 | NotificationadEShdslLTULoopAttenAlmACT | current | LTU Loop Attenuation Alarm | |
| 1.3.6.1.4.1.664.5.59.1.10.0.12 | NotificationadEShdslNTULossofSyncWordAlmCLR | current | NTU Loss of Sync Word Alarm | |
| 1.3.6.1.4.1.664.5.59.1.10.0.13 | NotificationadEShdslNTULossofSyncWordAlmACT | current | NTU Loss of Sync Word Alarm | |
| 1.3.6.1.4.1.664.5.59.1.10.0.14 | NotificationadEShdslNTUCRCErrorAlmCLR | current | NTU CRC Error | |
| 1.3.6.1.4.1.664.5.59.1.10.0.15 | NotificationadEShdslNTUCRCErrorAlmACT | current | NTU CRC Error | |
| 1.3.6.1.4.1.664.5.59.1.10.0.16 | NotificationadEShdslNTUSNRMarginAlmCLR | current | NTU SNR Margin Alarm | |
| 1.3.6.1.4.1.664.5.59.1.10.0.17 | NotificationadEShdslNTUSNRMarginAlmACT | current | NTU SNR Margin Alarm | |
| 1.3.6.1.4.1.664.5.59.1.10.0.18 | NotificationadEShdslNTULoopAttenAlmCLR | current | NTU Loop Attenuation Alarm | |
| 1.3.6.1.4.1.664.5.59.1.10.0.19 | NotificationadEShdslNTULoopAttenAlmACT | current | NTU Loop Attenuation Alarm | |
| 1.3.6.1.4.1.664.5.59.1.10.0.20 | NotificationadEShdslLTUESThreshCrossed | current | LTU Errored Seconds Threshold Crossed | |
| 1.3.6.1.4.1.664.5.59.1.10.0.21 | NotificationadEShdslLTUSESThreshCrossed | current | LTU Severely Errored Seconds Threshold Crossed | |
| 1.3.6.1.4.1.664.5.59.1.10.0.22 | NotificationadEShdslLTUUASThreshCrossed | current | LTU Unavailable Seconds Threshold Crossed | |
| 1.3.6.1.4.1.664.5.59.1.10.0.23 | NotificationadEShdslLTUCVCThreshCrossed | current | LTU Code Violation Count Threshold Crossed | |
| 1.3.6.1.4.1.664.5.59.1.10.0.24 | NotificationadEShdslLTULOSWSThreshCrossed | current | LTU Loss of Sync Word Seconds Threshold Crossed | |
| 1.3.6.1.4.1.664.5.59.1.10.0.25 | NotificationadEShdslLTUOSThreshCrossed | current | LTU Outage Seconds Threshold Crossed | |
| 1.3.6.1.4.1.664.5.59.1.10.0.26 | NotificationadEShdslNTUESThreshCrossed | current | NTU Errored Seconds Threshold Crossed | |
| 1.3.6.1.4.1.664.5.59.1.10.0.27 | NotificationadEShdslNTUSESThreshCrossed | current | NTU Severely Errored Seconds Threshold Crossed | |
| 1.3.6.1.4.1.664.5.59.1.10.0.28 | NotificationadEShdslNTUUASThreshCrossed | current | NTU Unavailable Seconds Threshold Crossed | |
| 1.3.6.1.4.1.664.5.59.1.10.0.29 | NotificationadEShdslNTUCVCThreshCrossed | current | NTU Code Violation Count Threshold Crossed | |
| 1.3.6.1.4.1.664.5.59.1.10.0.30 | NotificationadEShdslNTULOSWSThreshCrossed | current | NTU Loss of Sync Word Seconds Threshold Crossed | |
| 1.3.6.1.4.1.664.5.59.1.10.0.31 | NotificationadEShdslNTUOSThreshCrossed | current | NTU Outage Seconds Threshold Crossed | |
| 1.3.6.1.4.1.664.5.59.1.10.0.32 | NotificationadEShdslRemoteLossOfPower | current | Remote Unit has lost power | |
| 1.3.6.1.4.1.664.5.59.1.10.0.33 | NotificationadEShdslLTUES24HrThreshCrossed | current | LTU 24-Hour Errored Seconds Threshold Crossed | |
| 1.3.6.1.4.1.664.5.59.1.10.0.34 | NotificationadEShdslLTUSES24HrThreshCrossed | current | LTU 24-Hour Severely Errored Seconds Threshold Crossed | |
| 1.3.6.1.4.1.664.5.59.1.10.0.35 | NotificationadEShdslLTUUAS24HrThreshCrossed | current | LTU 24-Hour Unavailable Seconds Threshold Crossed | |
| 1.3.6.1.4.1.664.5.59.1.10.0.36 | NotificationadEShdslLTUCVC24HrThreshCrossed | current | LTU 24-Hour Code Violation Count Threshold Crossed | |
| 1.3.6.1.4.1.664.5.59.1.10.0.37 | NotificationadEShdslLTULOSWS24HrThreshCrossed | current | LTU 24-Hour Loss of Sync Word Seconds Threshold Crossed | |
| 1.3.6.1.4.1.664.5.59.1.10.0.38 | NotificationadEShdslLTUOS24HrThreshCrossed | current | LTU 24-Hour Outage Seconds Threshold Crossed | |
| 1.3.6.1.4.1.664.5.59.1.10.0.39 | NotificationadEShdslNTUES24HrThreshCrossed | current | NTU 24-Hour Errored Seconds Threshold Crossed | |
| 1.3.6.1.4.1.664.5.59.1.10.0.40 | NotificationadEShdslNTUSES24HrThreshCrossed | current | NTU 24-Hour Severely Errored Seconds Threshold Crossed | |
| 1.3.6.1.4.1.664.5.59.1.10.0.41 | NotificationadEShdslNTUUAS24HrThreshCrossed | current | NTU 24-Hour Unavailable Seconds Threshold Crossed | |
| 1.3.6.1.4.1.664.5.59.1.10.0.42 | NotificationadEShdslNTUCVC24HrThreshCrossed | current | NTU 24-Hour Code Violation Count Threshold Crossed | |
| 1.3.6.1.4.1.664.5.59.1.10.0.43 | NotificationadEShdslNTULOSWS24HrThreshCrossed | current | NTU 24-Hour Loss of Sync Word Seconds Threshold Crossed | |
| 1.3.6.1.4.1.664.5.59.1.10.0.44 | NotificationadEShdslNTUOS24HrThreshCrossed | current | NTU 24-Hour Outage Seconds Threshold Crossed | |
| 1.3.6.1.4.1.664.5.59.1.10.0.45 | NotificationadEShdslRegenLossofSignalAlmCLR | current | Loss of Signal Alarm | |
| 1.3.6.1.4.1.664.5.59.1.10.0.46 | NotificationadEShdslRegenLossofSignalAlmACT | current | Loss of Signal Alarm | |
| 1.3.6.1.4.1.664.5.59.1.10.0.47 | NotificationadEShdslRegenLossofSyncWordAlmCLR | current | Loss of Sync Word Alarm | |
| 1.3.6.1.4.1.664.5.59.1.10.0.48 | NotificationadEShdslRegenLossofSyncWordAlmACT | current | Loss of Sync Word Alarm | |
| 1.3.6.1.4.1.664.5.59.1.10.0.49 | NotificationadEShdslRegenCRCErrorAlmCLR | current | CRC Error | |
| 1.3.6.1.4.1.664.5.59.1.10.0.50 | NotificationadEShdslRegenCRCErrorAlmACT | current | CRC Error | |
| 1.3.6.1.4.1.664.5.59.1.10.0.51 | NotificationadEShdslRegenSNRMarginAlmCLR | current | SNR Margin Alarm | |
| 1.3.6.1.4.1.664.5.59.1.10.0.52 | NotificationadEShdslRegenSNRMarginAlmACT | current | SNR Margin Alarm | |
| 1.3.6.1.4.1.664.5.59.1.10.0.53 | NotificationadEShdslRegenLoopAttenAlmCLR | current | Loop Attenuation Alarm | |
| 1.3.6.1.4.1.664.5.59.1.10.0.54 | NotificationadEShdslRegenLoopAttenAlmACT | current | Loop Attenuation Alarm | |
| 1.3.6.1.4.1.664.5.59.1.10.0.55 | NotificationadEShdslRegenESThreshCrossed | current | Errored Seconds Threshold Crossed | |
| 1.3.6.1.4.1.664.5.59.1.10.0.56 | NotificationadEShdslRegenSESThreshCrossed | current | Severely Errored Seconds Threshold Crossed | |
| 1.3.6.1.4.1.664.5.59.1.10.0.57 | NotificationadEShdslRegenUASThreshCrossed | current | Unavailable Seconds Threshold Crossed | |
| 1.3.6.1.4.1.664.5.59.1.10.0.58 | NotificationadEShdslRegenCVCThreshCrossed | current | Code Violation Count Threshold Crossed | |
| 1.3.6.1.4.1.664.5.59.1.10.0.59 | NotificationadEShdslRegenLOSWSThreshCrossed | current | Loss of Sync Word Seconds Threshold Crossed | |
| 1.3.6.1.4.1.664.5.59.1.10.0.60 | NotificationadEShdslRegenOSThreshCrossed | current | Outage Seconds Threshold Crossed | |
| 1.3.6.1.4.1.664.5.59.1.10.0.61 | NotificationadEShdslRegenES24HrThreshCrossed | current | 24-Hour Errored Seconds Threshold Crossed | |
| 1.3.6.1.4.1.664.5.59.1.10.0.62 | NotificationadEShdslRegenSES24HrThreshCrossed | current | 24-Hour Severely Errored Seconds Threshold Crossed | |
| 1.3.6.1.4.1.664.5.59.1.10.0.63 | NotificationadEShdslRegenUAS24HrThreshCrossed | current | 24-Hour Unavailable Seconds Threshold Crossed | |
| 1.3.6.1.4.1.664.5.59.1.10.0.64 | NotificationadEShdslRegenCVC24HrThreshCrossed | current | 24-Hour Code Violation Count Threshold Crossed | |
| 1.3.6.1.4.1.664.5.59.1.10.0.65 | NotificationadEShdslRegenLOSWS24HrThreshCrossed | current | 24-Hour Loss of Sync Word Seconds Threshold Crossed | |
| 1.3.6.1.4.1.664.5.59.1.10.0.66 | NotificationadEShdslRegenOS24HrThreshCrossed | current | 24-Hour Outage Seconds Threshold Crossed | |
| 1.3.6.1.4.1.664.5.59.1.10.0.71 | NotificationadEShdslLoopbackEnabledCLR | current | Loopback Enabled Alarm | |
| 1.3.6.1.4.1.664.5.59.1.10.0.72 | NotificationadEShdslLoopbackEnabledACT | current | Loopback Enabled Alarm | |
| 1.3.6.1.4.1.664.5.59.1.10.0.80 | NotificationadEShdslRetrains15MinThreshCrossed | current | 15 Minute Retrains Threshold Crossed | |
| 1.3.6.1.4.1.664.5.59.1.10.0.81 | NotificationadEShdslHandshakeFailures15MinThreshCrossed | current | 15 Minute Handshake Failures Threshold Crossed | |
| 1.3.6.1.4.1.664.5.59.1.10.0.82 | NotificationadEShdslRetrains24HrThreshCrossed | current | 24 Hour Retrains Threshold Crossed | |
| 1.3.6.1.4.1.664.5.59.1.10.0.83 | NotificationadEShdslHandshakeFailures24HrThreshCrossed | current | 24 Hour Handshake Failures Threshold Crossed | |
| 1.3.6.1.4.1.664.5.59.1.10.0.84 | NotificationadEShdslBadSpliceDetected | current | Bad Splice Detection Alarm is generated when the BSD algorithm detects a potential bad splice event. | |
| 1.3.6.1.4.1.664.5.59.1.10.0.85 | NotificationadEShdslSruShortDetectAlmCLR | current | Short Detection Alarm clear | |
| 1.3.6.1.4.1.664.5.59.1.10.0.86 | NotificationadEShdslSruShortDetectAlmACT | current | Short Detection Alarm is generated when a regenerator element indicates a short has been detected on the span power interface. | |
| 1.3.6.1.4.1.664.5.59.1.10.0.87 | NotificationadEShdslSruGroundFaultDetectAlmCLR | current | Ground Fault Detection Alarm clear | |
| 1.3.6.1.4.1.664.5.59.1.10.0.88 | NotificationadEShdslSruGroundFaultDetectAlmACT | current | Ground Fault Detection Alarm is generated when a regenerator element indicates a ground fault has been detected on the span power interface. | |
| 1.3.6.1.4.1.664.5.59.1.10.0.89 | NotificationadEShdslSCIThreshCrossed | current | This alarm is generated when no command responses have been received within the configured threshold window. | |
| 1.3.6.1.4.1.664.5.59.1.11 | NodeadEShdslProductInfo | |||
| 1.3.6.1.4.1.664.6.10000.59.1.1 | IdentityadGenEShdslMIB | This MIB defines the objects for the SHDSL MIB. |