cisco/CISCO-SIBU-STACKABLE-DUAL-SPEED-HUB-MIB
54 objects
The MIB module that extends the REPEATER-MIB to manage CISCO low end stackable repeater products. For the purpose of this mib, a hub is a repeater group and stack is collection of one or more hubs interconnected via stack bus connectors.
Imported Objects
| CISCO-SMI | ciscoExperiment |
| RFC1213-MIB | PhysAddress |
| SNMP-REPEATER-MIB | rptrGroupIndex rptrPortGroupIndex rptrPortIndex |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE |
| SNMPv2-TC | DisplayString TEXTUAL-CONVENTION |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.10.44 | IdentityciscoSibuStackableDualSpeedHubMIB | The MIB module that extends the REPEATER-MIB to manage CISCO low end stackable repeater products. For the purpose of this mib, a hub is a repeater group and st… | ||
| 1.3.6.1.4.1.9.10.44.1 | NodeciscoSibuStackableDualSpeedHubMIBObjects | |||
| 1.3.6.1.4.1.9.10.44.1.1 | NodecssSystem | |||
| 1.3.6.1.4.1.9.10.44.1.1.1 | ScalarcssSystemLinkTraps | read-write | current | Indicates whether the stack is permitted to generate linkUp/linkDown traps for both repeater port and switch module's port. The stack provides only a single gl… |
| 1.3.6.1.4.1.9.10.44.1.2 | NodecssGroup | |||
| 1.3.6.1.4.1.9.10.44.1.2.1 | TablecssGroupTable | not-accessible | current | A list of member hubs in the stack. |
| 1.3.6.1.4.1.9.10.44.1.2.1.1 | RowcssGroupEntry | not-accessible | current | Configuration parameters for an individual hub. An entry is created by default for the master unit in the stack. A entry is created (removed) when a hub is con… |
| 1.3.6.1.4.1.9.10.44.1.2.1.1.1 | ColumncssGroupID | read-only | current | The hub identifier of unit in a stack. |
| 1.3.6.1.4.1.9.10.44.1.2.1.1.2 | ColumncssGroupType | read-only | current | The model type of the hub unit |
| 1.3.6.1.4.1.9.10.44.1.2.1.1.4 | ColumncssGroupSerialNo | read-only | current | Serial number of the hardware. |
| 1.3.6.1.4.1.9.10.44.1.2.1.1.5 | ColumncssGroupBoardRevision | read-only | current | Hardware version of the repeater board. |
| 1.3.6.1.4.1.9.10.44.1.2.1.1.6 | ColumncssGroupAgentBootVersion | read-only | current | Returns the version number of the dual-speed hub BOOT software residing in flash. The format is 'V1.2.3'. |
| 1.3.6.1.4.1.9.10.44.1.2.1.1.7 | ColumncssGroupAgentFirmwareVersion | read-only | current | Returns the version number of the dual-speed hub firmware residing in flash. The format is 'V1.2.3'. |
| 1.3.6.1.4.1.9.10.44.1.2.1.1.8 | ColumncssGroupAgentStatus | read-only | current | Status of this hub agent. Each stack allows only one SNMP primary agent. notPresent(1): The hub does not have an agent. primary(2): The agent of this hub is a … |
| 1.3.6.1.4.1.9.10.44.1.2.1.1.9 | ColumncssGroupAgentPhysAddress | read-only | current | MAC address of this hub's agent |
| 1.3.6.1.4.1.9.10.44.1.2.1.1.12 | ColumncssGroupInternalPowerState | read-only | current | Indicates the state of the internal power supply. off : The internal power supply is off. on : The internal power supply is on. |
| 1.3.6.1.4.1.9.10.44.1.2.1.1.13 | ColumncssGroupRedundantPowerState | read-only | current | Indicates the state of the external/backup power supply. off : the switch is not connected to a redundant power source. healthy : a redundant power source is c… |
| 1.3.6.1.4.1.9.10.44.1.2.1.1.14 | ColumncssGroupReset | read-write | current | Setting this object to reset(2) causes a complete reset of both hardware and software, but does not run the POST (Power On Self Test). Setting this object to n… |
| 1.3.6.1.4.1.9.10.44.1.2.1.1.15 | ColumncssGroupConfigDefaultReset | read-write | current | Setting this object to reset(2) causes a complete reset of both hardware and software, but does not run the POST (Power On Self Test). All configuration parame… |
| 1.3.6.1.4.1.9.10.44.1.2.1.1.16 | ColumncssGroupIsolatedState | read-write | current | Setting this object to isolated(1) causes this hub to be isolated from the back plane bus. Setting this object to attached(2) causes this hub to be attached to… |
| 1.3.6.1.4.1.9.10.44.1.3 | NodecssRepeaterPort | |||
| 1.3.6.1.4.1.9.10.44.1.3.1 | TablecssRepeaterPortTable | not-accessible | current | The list of repeater port configurations on each hub unit. |
| 1.3.6.1.4.1.9.10.44.1.3.1.1 | RowcssRepeaterPortEntry | not-accessible | current | Configuration parameters for an individual repeater port on a hub. The value of rptrPortIndex also indicates the physical port number of the port in the hub. A… |
| 1.3.6.1.4.1.9.10.44.1.3.1.1.1 | ColumncssRepeaterPortName | read-write | current | A descriptive string of up to 20 characters used by the network administrator to name a port. |
| 1.3.6.1.4.1.9.10.44.1.3.1.1.2 | ColumncssRepeaterPortControllerRevision | read-only | current | Returns the revision number of the port controller. |
| 1.3.6.1.4.1.9.10.44.1.3.1.1.3 | ColumncssRepeaterPortSpeedAdmin | read-write | current | Set to tenMbps(1) to operate in 10Mbps speed mode. Set to oneHundredMbps(2) to operate in 100Mbps speed mode. Set to autoNegotiate(3) to allow the switch to ne… |
| 1.3.6.1.4.1.9.10.44.1.3.1.1.4 | ColumncssRepeaterPortSpeedStatus | read-write | current | The operating speed of the port. |
| 1.3.6.1.4.1.9.10.44.1.3.1.1.5 | ColumncssRepeaterPortLinkStatus | read-only | current | The current port link status. |
| 1.3.6.1.4.1.9.10.44.1.4 | NodecssSwitchPort | |||
| 1.3.6.1.4.1.9.10.44.1.4.1 | TablecssSwitchPortTable | not-accessible | current | A list of switched ports on extension module on a each hub unit in the stack. |
| 1.3.6.1.4.1.9.10.44.1.4.1.1 | RowcssSwitchPortEntry | not-accessible | current | Configuration parameters for an individual switch module port. An entry is created for each switch port on a module is inserted into a hub in the stack. The co… |
| 1.3.6.1.4.1.9.10.44.1.4.1.1.1 | ColumncssSwitchPortModuleID | read-only | current | Unique ID number of a module unit in a hub as used in the command line interface. |
| 1.3.6.1.4.1.9.10.44.1.4.1.1.2 | ColumncssSwitchPortPortID | read-only | current | The unique ID identifying a port on an extension module on a hub as used in the command line interface. |
| 1.3.6.1.4.1.9.10.44.1.4.1.1.3 | ColumncssSwitchPortName | read-write | current | A descriptive string of up to 20 characters used by the network administrator to name a switch port. |
| 1.3.6.1.4.1.9.10.44.1.4.1.1.4 | ColumncssSwitchPortType | read-only | current | Type of switch module in this hub. |
| 1.3.6.1.4.1.9.10.44.1.4.1.1.5 | ColumncssSwitchPortControllerRevision | read-only | current | The revision number of the port controller. |
| 1.3.6.1.4.1.9.10.44.1.4.1.1.6 | ColumncssSwitchPortState | read-write | current | Setting this object to enabled(1) enables the port. Setting this object to disabled(2) disables the port. |
| 1.3.6.1.4.1.9.10.44.1.4.1.1.7 | ColumncssSwitchPortDuplexAdmin | read-write | current | Set to fullDuplex(1) to operate in full duplex mode: port will allow simultaneous transmit and receive which can double its bandwidth. Set to halfDuplex(2) to … |
| 1.3.6.1.4.1.9.10.44.1.4.1.1.8 | ColumncssSwitchPortDuplexStatus | read-only | current | The operating duplex mode of the switched port. |
| 1.3.6.1.4.1.9.10.44.1.4.1.1.9 | ColumncssSwitchPortSpeedAdmin | read-write | current | Set to tenMbps(1) to operate in 10Mbps speed mode. Set to oneHundredMbps(2) to operate in 100Mbps speed mode. Set to autoNegotiate(3) to allow the switch to ne… |
| 1.3.6.1.4.1.9.10.44.1.4.1.1.10 | ColumncssSwitchPortSpeedStatus | read-only | current | The operating speed of the switched port. |
| 1.3.6.1.4.1.9.10.44.1.4.1.1.11 | ColumncssSwitchPortLinkStatus | read-only | current | Indicates the link STATUS of switch port. |
| 1.3.6.1.4.1.9.10.44.2 | NodeciscoSibuStackableDualSpeedHubNotifications | |||
| 1.3.6.1.4.1.9.10.44.2.0 | NodeciscoSibuStackableDualSpeedHubNotificationsPrefix | |||
| 1.3.6.1.4.1.9.10.44.2.0.1 | NotificationciscoSibuStackableDualSpeedHubRptrPortLinkChange | current | This trap is generated whenever the value of cssRepeaterPortLinkStatus changes for a repeater port. | |
| 1.3.6.1.4.1.9.10.44.2.0.2 | NotificationciscoSibuStackableDualSpeedHubSwitchPortLinkChange | current | This trap is generated whenever the value of cssSwitchPortLinkStatus changes for a switch port on an extension module. | |
| 1.3.6.1.4.1.9.10.44.3 | NodeciscoSibuStackableDualSpeedHubMIBComformance | |||
| 1.3.6.1.4.1.9.10.44.3.1 | NodeciscoSibuStackableDualSpeedHubMIBCompliances | |||
| 1.3.6.1.4.1.9.10.44.3.1.1 | ComplianceciscoSibuStackableDualSpeedHubCompliance | current | The compliance statement for the Cisco Stackable Dual-Speed Hub products. | |
| 1.3.6.1.4.1.9.10.44.3.2 | NodeciscoSibuStackableDualSpeedHubMIBGroups | |||
| 1.3.6.1.4.1.9.10.44.3.2.1 | GroupciscoSibuStackableDualSpeedHubGroup | current | A collection of group objects for use with the Cisco Stackable Dual-Speed Hub products. | |
| 1.3.6.1.4.1.9.10.44.3.2.2 | GroupciscoSibuStackableDualSpeedHubRepeaterPortGroup | current | A collection of repeater port objects for use with the Cisco Stackable Dual-Speed Hub products. | |
| 1.3.6.1.4.1.9.10.44.3.2.3 | GroupciscoSibuStackableDualSpeedHubSwitchPortGroup | current | A collection of switch module port objects for use with the Cisco Stackable Dual-Speed Hub products. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| HubNumber | Integer32 (1..2147483647) | current | Represents the hub number that the system supports for stacking. The hub number represents the order in which a hub is stacked relative to other members of the stack. Lowest hub number represents the top member of the s… |