s412-MIB
247 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC-1212 | OBJECT-TYPE |
| RFC-1215 | TRAP-TYPE |
| RFC1155-SMI | Counter enterprises Gauge internet IpAddress mgmt NetworkAddress private TimeTicks |
| SNMPv2-TC | DisplayString |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.3052 | Nodeasentria | |||
| 1.3.6.1.4.1.3052.41 | Nodes412 | |||
| 1.3.6.1.4.1.3052.41.1 | Nodedevice | |||
| 1.3.6.1.4.1.3052.41.1.1 | ScalarserialNumber | read-only | mandatory | 8-character serial number |
| 1.3.6.1.4.1.3052.41.1.2 | ScalarfirmwareVersion | read-only | mandatory | Firmware version text string |
| 1.3.6.1.4.1.3052.41.1.3 | ScalarsiteID | read-write | mandatory | Site Identifier, up to 12 characters. |
| 1.3.6.1.4.1.3052.41.1.4 | ScalarsnmpManager | read-write | deprecated | This is snmp manager #1 |
| 1.3.6.1.4.1.3052.41.1.6 | ScalarforceTraps | read-write | mandatory | Any write non-zero forces set of traps to be send to the SNMP Manager |
| 1.3.6.1.4.1.3052.41.1.7 | ScalarthisTrapText | read-write | mandatory | A text string included in all traps |
| 1.3.6.1.4.1.3052.41.1.8 | ScalaralarmStatus | read-only | mandatory | A text status of all alarms |
| 1.3.6.1.4.1.3052.41.1.9 | ScalarsnmpManager1 | read-write | mandatory | SNMP manager #1 |
| 1.3.6.1.4.1.3052.41.1.10 | ScalarsnmpManager2 | read-write | mandatory | SNMP manager #2 |
| 1.3.6.1.4.1.3052.41.1.11 | ScalarsnmpManager3 | read-write | mandatory | SNMP manager #3 |
| 1.3.6.1.4.1.3052.41.1.12 | ScalarsnmpManager4 | read-write | mandatory | SNMP manager #4 |
| 1.3.6.1.4.1.3052.41.1.13 | ScalarstatusRepeatHours | read-write | mandatory | 0=none, 1-24 Number of Hours between Status Traps being Sent |
| 1.3.6.1.4.1.3052.41.1.14 | ScalarserialTimeout | read-write | mandatory | 5-30, Minutes of non-activity timeout on serial setup |
| 1.3.6.1.4.1.3052.41.1.15 | ScalarpowerupTrapsend | read-write | mandatory | 0-no, 1-yes, send traps for all sensors on powerup |
| 1.3.6.1.4.1.3052.41.1.16 | ScalarnetlossTrapsend | read-write | mandatory | 0-no, 1-yes, send traps for detected netloss and back up |
| 1.3.6.1.4.1.3052.41.1.17 | ScalarbuildID | read-only | mandatory | 5-chars max text for build identifier |
| 1.3.6.1.4.1.3052.41.2 | Nodecontacts | |||
| 1.3.6.1.4.1.3052.41.2.1 | Nodecontact1 | |||
| 1.3.6.1.4.1.3052.41.2.1.1 | Scalarcontact1Name | read-write | mandatory | Name for contact, up to 30 characters |
| 1.3.6.1.4.1.3052.41.2.1.2 | Scalarcontact1State | read-only | mandatory | Current State of Contact, 0-open 1-closed |
| 1.3.6.1.4.1.3052.41.2.1.3 | Scalarcontact1AlarmEnable | read-write | mandatory | 0-alarms disabled 1-alarms enabled |
| 1.3.6.1.4.1.3052.41.2.1.4 | Scalarcontact1ActiveDirection | read-write | mandatory | 0-alarm on open 1-alarm on closed |
| 1.3.6.1.4.1.3052.41.2.1.5 | Scalarcontact1Threshold | read-write | mandatory | Number of seconds that the contact must remain in a state before generating a trap, range 0-255 |
| 1.3.6.1.4.1.3052.41.2.1.6 | Scalarcontact1ReturnNormalTrap | read-write | mandatory | 0-return to normal traps not sent, 1-sent |
| 1.3.6.1.4.1.3052.41.2.1.7 | Scalarcontact1TrapRepeat | read-write | mandatory | 0-no repeats. 1-255 number of minutes between repeats of alarm traps. |
| 1.3.6.1.4.1.3052.41.2.1.8 | Scalarcontact1Severity | read-write | mandatory | 1-minor 2-major 3-critical 4-severe 5-warning |
| 1.3.6.1.4.1.3052.41.2.2 | Nodecontact2 | |||
| 1.3.6.1.4.1.3052.41.2.2.1 | Scalarcontact2Name | read-write | mandatory | Name for contact, up to 30 characters |
| 1.3.6.1.4.1.3052.41.2.2.2 | Scalarcontact2State | read-only | mandatory | Current State of Contact, 0-open 1-closed |
| 1.3.6.1.4.1.3052.41.2.2.3 | Scalarcontact2AlarmEnable | read-write | mandatory | 0-no alarms 1-alarms enabled |
| 1.3.6.1.4.1.3052.41.2.2.4 | Scalarcontact2ActiveDirection | read-write | mandatory | 0-alarm on open 1-alarm on closed |
| 1.3.6.1.4.1.3052.41.2.2.5 | Scalarcontact2Threshold | read-write | mandatory | Number of seconds must be in a state to be 'open' or 'closed' |
| 1.3.6.1.4.1.3052.41.2.2.6 | Scalarcontact2ReturnNormalTrap | read-write | mandatory | 0-not sent, 1-sent |
| 1.3.6.1.4.1.3052.41.2.2.7 | Scalarcontact2TrapRepeat | read-write | mandatory | 0-no repeats. 1-255 number of minutes between repeats of alarm traps |
| 1.3.6.1.4.1.3052.41.2.2.8 | Scalarcontact2Severity | read-write | mandatory | 1-minor 2-major 3-critical 4-severe 5-warning |
| 1.3.6.1.4.1.3052.41.2.3 | Nodecontact3 | |||
| 1.3.6.1.4.1.3052.41.2.3.1 | Scalarcontact3Name | read-write | mandatory | Name for contact, up to 30 characters |
| 1.3.6.1.4.1.3052.41.2.3.2 | Scalarcontact3State | read-only | mandatory | Current State of Contact, 0-open 1-closed |
| 1.3.6.1.4.1.3052.41.2.3.3 | Scalarcontact3AlarmEnable | read-write | mandatory | 0-no alarms 1-alarms enabled |
| 1.3.6.1.4.1.3052.41.2.3.4 | Scalarcontact3ActiveDirection | read-write | mandatory | 0-alarm on open 1-alarm on closed |
| 1.3.6.1.4.1.3052.41.2.3.5 | Scalarcontact3Threshold | read-write | mandatory | Number of seconds must be in a state to be 'open' or 'closed' |
| 1.3.6.1.4.1.3052.41.2.3.6 | Scalarcontact3ReturnNormalTrap | read-write | mandatory | 0-not sent, 1-sent |
| 1.3.6.1.4.1.3052.41.2.3.7 | Scalarcontact3TrapRepeat | read-write | mandatory | 0-no repeats. 1-255 number of minutes between repeats of alarm traps |
| 1.3.6.1.4.1.3052.41.2.3.8 | Scalarcontact3Severity | read-write | mandatory | 1-minor 2-major 3-critical 4-severe 5-warning |
| 1.3.6.1.4.1.3052.41.2.4 | Nodecontact4 | |||
| 1.3.6.1.4.1.3052.41.2.4.1 | Scalarcontact4Name | read-write | mandatory | Name for contact, up to 30 characters |
| 1.3.6.1.4.1.3052.41.2.4.2 | Scalarcontact4State | read-only | mandatory | Current State of Contact, 0-open 1-closed |
| 1.3.6.1.4.1.3052.41.2.4.3 | Scalarcontact4AlarmEnable | read-write | mandatory | 0-no alarms 1-alarms enabled |
| 1.3.6.1.4.1.3052.41.2.4.4 | Scalarcontact4ActiveDirection | read-write | mandatory | 0-alarm on open 1-alarm on closed |
| 1.3.6.1.4.1.3052.41.2.4.5 | Scalarcontact4Threshold | read-write | mandatory | Number of seconds must be in a state to be 'open' or 'closed' |
| 1.3.6.1.4.1.3052.41.2.4.6 | Scalarcontact4ReturnNormalTrap | read-write | mandatory | 0-not sent, 1-sent |
| 1.3.6.1.4.1.3052.41.2.4.7 | Scalarcontact4TrapRepeat | read-write | mandatory | 0-no repeats. 1-255 number of minutes between repeats of alarm traps |
| 1.3.6.1.4.1.3052.41.2.4.8 | Scalarcontact4Severity | read-write | mandatory | 1-minor 2-major 3-critical 4-severe 5-warning |
| 1.3.6.1.4.1.3052.41.2.5 | Nodecontact5 | |||
| 1.3.6.1.4.1.3052.41.2.5.1 | Scalarcontact5Name | read-write | mandatory | Name for contact, up to 30 characters |
| 1.3.6.1.4.1.3052.41.2.5.2 | Scalarcontact5State | read-only | mandatory | Current State of Contact, 0-open 1-closed |
| 1.3.6.1.4.1.3052.41.2.5.3 | Scalarcontact5AlarmEnable | read-write | mandatory | 0-no alarms 1-alarms enabled |
| 1.3.6.1.4.1.3052.41.2.5.4 | Scalarcontact5ActiveDirection | read-write | mandatory | 0-alarm on open 1-alarm on closed |
| 1.3.6.1.4.1.3052.41.2.5.5 | Scalarcontact5Threshold | read-write | mandatory | Number of seconds must be in a state to be 'open' or 'closed' |
| 1.3.6.1.4.1.3052.41.2.5.6 | Scalarcontact5ReturnNormalTrap | read-write | mandatory | 0-not sent, 1-sent |
| 1.3.6.1.4.1.3052.41.2.5.7 | Scalarcontact5TrapRepeat | read-write | mandatory | 0-no repeats. 1-255 number of minutes between repeats of alarm traps |
| 1.3.6.1.4.1.3052.41.2.5.8 | Scalarcontact5Severity | read-write | mandatory | 1-minor 2-major 3-critical 4-severe 5-warning |
| 1.3.6.1.4.1.3052.41.2.6 | Nodecontact6 | |||
| 1.3.6.1.4.1.3052.41.2.6.1 | Scalarcontact6Name | read-write | mandatory | Name for contact, up to 30 characters |
| 1.3.6.1.4.1.3052.41.2.6.2 | Scalarcontact6State | read-only | mandatory | Current State of Contact, 0-open 1-closed |
| 1.3.6.1.4.1.3052.41.2.6.3 | Scalarcontact6AlarmEnable | read-write | mandatory | 0-no alarms 1-alarms enabled |
| 1.3.6.1.4.1.3052.41.2.6.4 | Scalarcontact6ActiveDirection | read-write | mandatory | 0-alarm on open 1-alarm on closed |
| 1.3.6.1.4.1.3052.41.2.6.5 | Scalarcontact6Threshold | read-write | mandatory | Number of seconds must be in a state to be 'open' or 'closed' |
| 1.3.6.1.4.1.3052.41.2.6.6 | Scalarcontact6ReturnNormalTrap | read-write | mandatory | 0-not sent, 1-sent |
| 1.3.6.1.4.1.3052.41.2.6.7 | Scalarcontact6TrapRepeat | read-write | mandatory | 0-no repeats. 1-255 number of minutes between repeats of alarm traps. |
| 1.3.6.1.4.1.3052.41.2.6.8 | Scalarcontact6Severity | read-write | mandatory | 1-minor 2-major 3-critical 4-severe 5-warning |
| 1.3.6.1.4.1.3052.41.3 | Noderelays | |||
| 1.3.6.1.4.1.3052.41.3.1 | Noderelay1 | |||
| 1.3.6.1.4.1.3052.41.3.1.1 | Scalarrelay1Name | read-write | mandatory | Name for relay, up to 30 characters |
| 1.3.6.1.4.1.3052.41.3.1.2 | Scalarrelay1CurrentState | read-write | mandatory | 0-opened, 1-closed |
| 1.3.6.1.4.1.3052.41.3.1.3 | Scalarrelay1PowerupState | read-write | mandatory | 0-opened, 1-closed |
| 1.3.6.1.4.1.3052.41.3.2 | Noderelay2 | |||
| 1.3.6.1.4.1.3052.41.3.2.1 | Scalarrelay2Name | read-write | mandatory | Name for relay, up to 30 characters |
| 1.3.6.1.4.1.3052.41.3.2.2 | Scalarrelay2CurrentState | read-write | mandatory | 0-opened, 1-closed |
| 1.3.6.1.4.1.3052.41.3.2.3 | Scalarrelay2PowerupState | read-write | mandatory | 0-opened, 1-closed |
| 1.3.6.1.4.1.3052.41.4 | Nodetempsensor | |||
| 1.3.6.1.4.1.3052.41.4.1 | ScalartempValue | read-only | mandatory | Current Temperature Value, in C or F based on 1.3.6.1.4.1.3052.41.4.10 |
| 1.3.6.1.4.1.3052.41.4.2 | ScalartempAlarmEnable | read-write | mandatory | 0=alarms disabled, 1=alarms enabled |
| 1.3.6.1.4.1.3052.41.4.3 | ScalartempHighLevel | read-write | mandatory | Level at which the High alarm goes active |
| 1.3.6.1.4.1.3052.41.4.4 | ScalartempVeryHighLevel | read-write | mandatory | Level at which the Very High alarm goes active |
| 1.3.6.1.4.1.3052.41.4.5 | ScalartempLowLevel | read-write | mandatory | Level at which the Low alarm goes active |
| 1.3.6.1.4.1.3052.41.4.6 | ScalartempVeryLowLevel | read-write | mandatory | Level at which the Very Low alarm goes active |
| 1.3.6.1.4.1.3052.41.4.7 | ScalartempAlarmThreshold | read-write | mandatory | Seconds must be in a range to be an alarm |
| 1.3.6.1.4.1.3052.41.4.8 | ScalartempReturnNormalTrap | read-write | mandatory | 0-not sent, 1-send trap on return to normal range |
| 1.3.6.1.4.1.3052.41.4.9 | ScalartempTrapRepeat | read-write | mandatory | 0-no repeats. 1-255 number of minutes between repeats of alarm traps. |
| 1.3.6.1.4.1.3052.41.4.10 | ScalartempMode | read-write | mandatory | 0=all temp readings and levels in degrees F, 1=in degrees C |
| 1.3.6.1.4.1.3052.41.4.11 | ScalartempHighSeverity | read-write | mandatory | High Level Severity 1-minor 2-major 3-critical 4-severe 5-warning |
| 1.3.6.1.4.1.3052.41.4.12 | ScalartempVeryHighSeverity | read-write | mandatory | Very High Level Severity 1-minor 2-major 3-critical 4-severe 5-warning |
| 1.3.6.1.4.1.3052.41.4.13 | ScalartempLowSeverity | read-write | mandatory | Low Level Severity 1-minor 2-major 3-critical 4-severe 5-warning |
| 1.3.6.1.4.1.3052.41.4.14 | ScalartempVeryLowSeverity | read-write | mandatory | Very Low Level Severity 1-minor 2-major 3-critical 4-severe 5-warning |
| 1.3.6.1.4.1.3052.41.4.15 | ScalartempName | read-write | mandatory | Name for temperature sensor, up to 30 characters |
| 1.3.6.1.4.1.3052.41.5 | Nodehumiditysensor | |||
| 1.3.6.1.4.1.3052.41.5.1 | ScalarhumidityValue | read-only | mandatory | Current Relative Humidity Value (0-100%) |
| 1.3.6.1.4.1.3052.41.5.2 | ScalarhumidityAlarmEnable | read-write | mandatory | 0=alarms disabled, 1=alarms enabled |
| 1.3.6.1.4.1.3052.41.5.3 | ScalarhumidityHighLevel | read-write | mandatory | Level at which the High alarm goes active |
| 1.3.6.1.4.1.3052.41.5.4 | ScalarhumidityVeryHighLevel | read-write | mandatory | Level at which the Very High alarm goes active |
| 1.3.6.1.4.1.3052.41.5.5 | ScalarhumidityLowLevel | read-write | mandatory | Level at which the Low alarm goes active |
| 1.3.6.1.4.1.3052.41.5.6 | ScalarhumidityVeryLowLevel | read-write | mandatory | Level at which the Very Low alarm goes active |
| 1.3.6.1.4.1.3052.41.5.7 | ScalarhumidityAlarmThreshold | read-write | mandatory | Seconds must be in a range to be an alarm |
| 1.3.6.1.4.1.3052.41.5.8 | ScalarhumidityReturnNormalTrap | read-write | mandatory | 0-not sent, 1-send trap on return to normal range |
| 1.3.6.1.4.1.3052.41.5.9 | ScalarhumidityTrapRepeat | read-write | mandatory | 0-no repeats. 1-255 number of minutes between repeats of alarm traps. |
| 1.3.6.1.4.1.3052.41.5.10 | ScalarhumidityHighSeverity | read-write | mandatory | High Level Severity 1-minor 2-major 3-critical 4-severe 5-warning |
| 1.3.6.1.4.1.3052.41.5.11 | ScalarhumidityVeryHighSeverity | read-write | mandatory | Very High Level Severity 1-minor 2-major 3-critical 4-severe 5-warning |
| 1.3.6.1.4.1.3052.41.5.12 | ScalarhumidityLowSeverity | read-write | mandatory | Low Level Severity 1-minor 2-major 3-critical 4-severe 5-warning |
| 1.3.6.1.4.1.3052.41.5.13 | ScalarhumidityVeryLowSeverity | read-write | mandatory | Very Low Level Severity 1-minor 2-major 3-critical 4-severe 5-warning |
| 1.3.6.1.4.1.3052.41.5.14 | ScalarhumidityName | read-write | mandatory | Name for humidity sensor, up to 30 characters |
| 1.3.6.1.4.1.3052.41.6 | Nodepassthrough | |||
| 1.3.6.1.4.1.3052.41.6.1 | ScalarptNeedPassword | read-write | mandatory | 0-no 1-yes, is password required for passthrough connection. |
| 1.3.6.1.4.1.3052.41.6.2 | ScalarptSayLoginText | read-write | mandatory | 0-no 1-yes, is passthrough login text displayed on connection. |
| 1.3.6.1.4.1.3052.41.6.3 | ScalarptLoginText | read-write | mandatory | 0-24 char string which may be displayed on socket connection. Requires that ptSayLoginText be enabled to display this string. |
| 1.3.6.1.4.1.3052.41.6.4 | ScalarptSaySiteID | read-write | mandatory | 0-no 1-yes, is SiteID displayed on pass through connection. |
| 1.3.6.1.4.1.3052.41.6.5 | ScalarptUsername | read-write | mandatory | 0-16 char string for Username used in serial passthrough connections |
| 1.3.6.1.4.1.3052.41.6.6 | ScalarptPassword | read-write | mandatory | 0-16 char string for Password used in serial passthrough connections |
| 1.3.6.1.4.1.3052.41.6.7 | ScalarptTimeout | read-write | mandatory | number of minutes (1-255) of idle activity (both directions) which causes disconnect. 0-never |
| 1.3.6.1.4.1.3052.41.6.8 | ScalarptEscChar | read-write | mandatory | ASCII character code (e.g, Escape=27) which if entered on the tcp port three times in a row causes disconnect. 0-none |
| 1.3.6.1.4.1.3052.41.6.9 | ScalarptLfstripToPort | read-write | mandatory | 0-no 1-yes linefeed characters received on TCP connection are removed from stream to serial port |
| 1.3.6.1.4.1.3052.41.6.10 | ScalarptLfstripFromPort | read-write | mandatory | 0-no 1-yes linefeed characters received on serial port are removed from stream to TCP connection |
| 1.3.6.1.4.1.3052.41.6.11 | ScalarptSerialBaudrate | read-write | mandatory | 300 600 1200 2400 4800 9600 19200 baud are allowed values |
| 1.3.6.1.4.1.3052.41.6.12 | ScalarptSerialWordlength | read-write | mandatory | 7 or 8 bit word selection |
| 1.3.6.1.4.1.3052.41.6.13 | ScalarptSerialParity | read-write | mandatory | N E O are allowed values for parity (none, even, odd) [a single-character string] |
| 1.3.6.1.4.1.3052.41.6.14 | ScalarptTCPPortnumber | read-write | mandatory | IP port number for passthrough connection (range 1024-65534) |
| 1.3.6.1.4.1.3052.41.7 | Nodeftp | |||
| 1.3.6.1.4.1.3052.41.7.1 | ScalarftpUsername | read-write | mandatory | 0-16 char string for Username used in ftp server for updates |
| 1.3.6.1.4.1.3052.41.7.2 | ScalarftpPassword | read-write | mandatory | 0-16 char string for Password used in ftp server for updates |
| 1.3.6.1.4.1.3052.41.8 | Nodeanalog | |||
| 1.3.6.1.4.1.3052.41.8.1 | Nodeanalog1 | |||
| 1.3.6.1.4.1.3052.41.8.1.1 | Scalaranalog1Value | read-only | mandatory | Value of current analog reading, in 1/100 volt, +- 9999 range |
| 1.3.6.1.4.1.3052.41.8.1.2 | Scalaranalog1AlarmEnable | read-write | mandatory | 0=no alarms, 1=send alarms |
| 1.3.6.1.4.1.3052.41.8.1.3 | Scalaranalog1HighLevel | read-write | mandatory | Level at which the High alarm goes active |
| 1.3.6.1.4.1.3052.41.8.1.4 | Scalaranalog1VeryHighLevel | read-write | mandatory | Level at which the Very High alarm goes active |
| 1.3.6.1.4.1.3052.41.8.1.5 | Scalaranalog1LowLevel | read-write | mandatory | Level at which the Low alarm goes active |
| 1.3.6.1.4.1.3052.41.8.1.6 | Scalaranalog1VeryLowLevel | read-write | mandatory | Level at which the Very Low alarm goes active |
| 1.3.6.1.4.1.3052.41.8.1.7 | Scalaranalog1AlarmThreshold | read-write | mandatory | Seconds must be in a range to be an alarm |
| 1.3.6.1.4.1.3052.41.8.1.8 | Scalaranalog1ReturnNormalTrap | read-write | mandatory | 0-not sent, 1-send trap on return to normal range |
| 1.3.6.1.4.1.3052.41.8.1.9 | Scalaranalog1TrapRepeat | read-write | mandatory | 0-no repeats else number of minutes between repeats of trap |
| 1.3.6.1.4.1.3052.41.8.1.10 | Scalaranalog1HighSeverity | read-write | mandatory | High Level Severity 1-minor 2-major 3-critical 4-severe 5-warning |
| 1.3.6.1.4.1.3052.41.8.1.11 | Scalaranalog1VeryHighSeverity | read-write | mandatory | Very High Level Severity 1-minor 2-major 3-critical 4-severe 5-warning |
| 1.3.6.1.4.1.3052.41.8.1.12 | Scalaranalog1LowSeverity | read-write | mandatory | Low Level Severity 1-minor 2-major 3-critical 4-severe 5-warning |
| 1.3.6.1.4.1.3052.41.8.1.13 | Scalaranalog1VeryLowSeverity | read-write | mandatory | Very Low Level Severity 1-minor 2-major 3-critical 4-severe 5-warning |
| 1.3.6.1.4.1.3052.41.8.1.14 | Scalaranalog1Name | read-write | mandatory | Name for analog sensor 1, up to 30 characters |
| 1.3.6.1.4.1.3052.41.8.2 | Nodeanalog2 | |||
| 1.3.6.1.4.1.3052.41.8.2.1 | Scalaranalog2Value | read-only | mandatory | Value of current analog reading, in 1/100 volt, +- 9999 range |
| 1.3.6.1.4.1.3052.41.8.2.2 | Scalaranalog2AlarmEnable | read-write | mandatory | 0=no alarms, 1=send alarms |
| 1.3.6.1.4.1.3052.41.8.2.3 | Scalaranalog2HighLevel | read-write | mandatory | Level at which the High alarm goes active |
| 1.3.6.1.4.1.3052.41.8.2.4 | Scalaranalog2VeryHighLevel | read-write | mandatory | Level at which the Very High alarm goes active |
| 1.3.6.1.4.1.3052.41.8.2.5 | Scalaranalog2LowLevel | read-write | mandatory | Level at which the Low alarm goes active |
| 1.3.6.1.4.1.3052.41.8.2.6 | Scalaranalog2VeryLowLevel | read-write | mandatory | Level at which the Very Low alarm goes active |
| 1.3.6.1.4.1.3052.41.8.2.7 | Scalaranalog2AlarmThreshold | read-write | mandatory | Seconds must be in a range to be an alarm |
| 1.3.6.1.4.1.3052.41.8.2.8 | Scalaranalog2ReturnNormalTrap | read-write | mandatory | 0-not sent, 1-send trap on return to normal range |
| 1.3.6.1.4.1.3052.41.8.2.9 | Scalaranalog2TrapRepeat | read-write | mandatory | 0-no repeats else number of minutes between repeats of trap |
| 1.3.6.1.4.1.3052.41.8.2.10 | Scalaranalog2HighSeverity | read-write | mandatory | High Level Severity 1-minor 2-major 3-critical 4-severe 5-warning |
| 1.3.6.1.4.1.3052.41.8.2.11 | Scalaranalog2VeryHighSeverity | read-write | mandatory | Very High Level Severity 1-minor 2-major 3-critical 4-severe 5-warning |
| 1.3.6.1.4.1.3052.41.8.2.12 | Scalaranalog2LowSeverity | read-write | mandatory | Low Level Severity 1-minor 2-major 3-critical 4-severe 5-warning |
| 1.3.6.1.4.1.3052.41.8.2.13 | Scalaranalog2VeryLowSeverity | read-write | mandatory | Very Low Level Severity 1-minor 2-major 3-critical 4-severe 5-warning |
| 1.3.6.1.4.1.3052.41.8.2.14 | Scalaranalog2Name | read-write | mandatory | Name for analog sensor 2, up to 30 characters |
| 1.3.6.1.4.1.3052.41.10 | NodeeventSensorStatus | |||
| 1.3.6.1.4.1.3052.41.10.1 | TableesPointTable | not-accessible | mandatory | This table organizes 4 basic attributes of points. A point is a particular sensor on an EventSensor (e.g., temperature, humidity, contact closure 2, relay 5, e… |
| 1.3.6.1.4.1.3052.41.10.1.1 | RowesPointEntry | not-accessible | mandatory | Entry for EventSensor point table |
| 1.3.6.1.4.1.3052.41.10.1.1.1 | ColumnesIndexES | read-only | mandatory | The part of the point index that refers to an EventSensor. The point index is a string of 3 numbers separated by periods. It contains all the information neces… |
| 1.3.6.1.4.1.3052.41.10.1.1.2 | ColumnesIndexPC | read-only | mandatory | The part of the point index that refers to point class. The point index is a string of 3 numbers separated by periods. It contains all the information necessar… |
| 1.3.6.1.4.1.3052.41.10.1.1.3 | ColumnesIndexPoint | read-only | mandatory | The part of the point index that delineates which sensor on the EventSensor. So this combined with esIndexPC (Point Class or type) and esIndexES (which EventSe… |
| 1.3.6.1.4.1.3052.41.10.1.1.4 | ColumnesPointName | read-write | mandatory | The name of the point on an EventSensor. For example, 'AC temp' (in the case of the temperature sensor on an EventSensor). There can be multiple points of the … |
| 1.3.6.1.4.1.3052.41.10.1.1.5 | ColumnesPointInEventState | read-write | mandatory | A number referring to the event state of a point on an EventSensor. This number can have different meanings depending on the point class. If the point class is… |
| 1.3.6.1.4.1.3052.41.10.1.1.6 | ColumnesPointValueInt | read-write | mandatory | A number referring to the value of a point on an EventSensor. If the point class is temperature, then this object is the temperature in its configured scale (d… |
| 1.3.6.1.4.1.3052.41.10.1.1.7 | ColumnesPointValueStr | read-only | mandatory | A string referring to the value of a point on an EventSensor. For contact closures and relays this object is either 'Open' or 'Closed'. For temperature and hum… |
| 1.3.6.1.4.1.3052.41.11 | NodeeventSensorConfig | |||
| 1.3.6.1.4.1.3052.41.11.1 | ScalaresNumberEventSensors | read-only | mandatory | The number of EventSensors recognized by the s412 Range: 0-4 |
| 1.3.6.1.4.1.3052.41.11.2 | TableesTable | not-accessible | mandatory | The table of what EventSensors are attached to the unit |
| 1.3.6.1.4.1.3052.41.11.2.1 | RowesEntry | not-accessible | mandatory | Table entry for EventSensor table |
| 1.3.6.1.4.1.3052.41.11.2.1.1 | ColumnesIndex | read-only | mandatory | This number refers to an EventSensor; it has the same meaning as the esIndexES object (see above), except that this object is used only within the esTable bran… |
| 1.3.6.1.4.1.3052.41.11.2.1.2 | ColumnesID | read-only | mandatory | The factory-assigned ID of the EventSensor |
| 1.3.6.1.4.1.3052.41.11.2.1.3 | ColumnesNumberTempSensors | read-only | mandatory | The number of temperature sensors on the EventSensor |
| 1.3.6.1.4.1.3052.41.11.2.1.4 | ColumnesTempReportingMode | read-only | mandatory | Description of how temperature values should be interpreted. |
| 1.3.6.1.4.1.3052.41.11.2.1.5 | ColumnesNumberCCs | read-only | mandatory | The number of contact closures on the EventSensor. |
| 1.3.6.1.4.1.3052.41.11.2.1.6 | ColumnesCCReportingMode | read-only | mandatory | Description of how CC values should be interpreted. |
| 1.3.6.1.4.1.3052.41.11.2.1.7 | ColumnesNumberHumidSensors | read-only | mandatory | The number of humidity sensors on the EventSensor. |
| 1.3.6.1.4.1.3052.41.11.2.1.8 | ColumnesHumidReportingMode | read-only | mandatory | Description of how humidity sensor values should be interpreted. |
| 1.3.6.1.4.1.3052.41.11.2.1.13 | ColumnesNumberAnalog | read-only | mandatory | The number of analog inputs on the EventSensor. |
| 1.3.6.1.4.1.3052.41.11.2.1.14 | ColumnesAnalogReportingMode | read-only | mandatory | Description of how analog input values should be interpreted. |
| 1.3.6.1.4.1.3052.41.11.2.1.15 | ColumnesNumberRelayOutputs | read-only | mandatory | The number of relay outputs on the EventSensor |
| 1.3.6.1.4.1.3052.41.11.2.1.16 | ColumnesRelayReportingMode | read-only | mandatory | Description of how relay output values should be interpreted. |
| 1.3.6.1.4.1.3052.41.99 | Nodetechsupport | |||
| 1.3.6.1.4.1.3052.41.99.1 | ScalartechsupportIPAddress | read-write | mandatory | May read or Set IP Address, takes effect on restart |
| 1.3.6.1.4.1.3052.41.99.2 | ScalartechsupportNetMask | read-write | mandatory | May read or Set NetMask, takes effect on restart |
| 1.3.6.1.4.1.3052.41.99.3 | ScalartechsupportRouter | read-write | mandatory | May read or Set Router IP Address, takes effect on restart |
| 1.3.6.1.4.1.3052.41.99.4 | ScalartechsupportRestart | read-write | mandatory | Reads as 0, any Write resets unit so new IP, Netmask, Router may be used |
| 1.3.6.1.4.1.3052.41.99.5 | ScalartechsupportVersionNumber | read-write | mandatory | Version Number of Firmware |
| 1.3.6.1.4.1.3052.41.100 | Nodemibend | |||
| 1.3.6.1.4.1.3052.41.100.1 | ScalarmibendObject | read-only | mandatory | An object after all active mib items, to help some managers compile |
| 1.3.6.1.4.1.3052.41.20001 | Nodecontact1ActiveTrap | Sent to show Contact 1 is in the alarm state | ||
| 1.3.6.1.4.1.3052.41.20002 | Nodecontact2ActiveTrap | Sent to show Contact 2 is in the alarm state | ||
| 1.3.6.1.4.1.3052.41.20003 | Nodecontact3ActiveTrap | Sent to show Contact 3 is in the alarm state | ||
| 1.3.6.1.4.1.3052.41.20004 | Nodecontact4ActiveTrap | Sent to show Contact 4 is in the alarm state | ||
| 1.3.6.1.4.1.3052.41.20005 | Nodecontact5ActiveTrap | Sent to show Contact 5 is in the alarm state | ||
| 1.3.6.1.4.1.3052.41.20006 | Nodecontact6ActiveTrap | Sent to show Contact 6 is in the alarm state | ||
| 1.3.6.1.4.1.3052.41.20010 | NodetempHighTrap | Sent to show Temp exceeded High Temp Threshold | ||
| 1.3.6.1.4.1.3052.41.20011 | NodetempVeryHighTrap | Sent to show Temp exceeded Very High Temp Threshold | ||
| 1.3.6.1.4.1.3052.41.20012 | NodetempLowTrap | Sent to show Temp went below Low Temp Threshold | ||
| 1.3.6.1.4.1.3052.41.20013 | NodetempVeryLowTrap | Sent to show Temp went below Very Low Temp Threshold | ||
| 1.3.6.1.4.1.3052.41.20020 | NodehumidityHighTrap | Sent to show humidity exceeded High humidity Threshold | ||
| 1.3.6.1.4.1.3052.41.20021 | NodehumidityVeryHighTrap | Sent to show humidity exceeded Very High humidity Threshold | ||
| 1.3.6.1.4.1.3052.41.20022 | NodehumidityLowTrap | Sent to show humidity went below Low humidity Threshold | ||
| 1.3.6.1.4.1.3052.41.20023 | NodehumidityVeryLowTrap | Sent to show humidity went below Very Low humidity Threshold | ||
| 1.3.6.1.4.1.3052.41.20030 | Nodeanalog1HighTrap | Sent to show analog1 exceeded High analog1 Threshold | ||
| 1.3.6.1.4.1.3052.41.20031 | Nodeanalog1VeryHighTrap | Sent to show analog1 exceeded Very High analog1 Threshold | ||
| 1.3.6.1.4.1.3052.41.20032 | Nodeanalog1LowTrap | Sent to show analog1 went below Low analog1 Threshold | ||
| 1.3.6.1.4.1.3052.41.20033 | Nodeanalog1VeryLowTrap | Sent to show analog1 went below Very Low analog1 Threshold | ||
| 1.3.6.1.4.1.3052.41.20040 | Nodeanalog2HighTrap | Sent to show analog2 exceeded High analog2 Threshold | ||
| 1.3.6.1.4.1.3052.41.20041 | Nodeanalog2VeryHighTrap | Sent to show analog2 exceeded Very High analog2 Threshold | ||
| 1.3.6.1.4.1.3052.41.20042 | Nodeanalog2LowTrap | Sent to show analog2 went below Low analog2 Threshold | ||
| 1.3.6.1.4.1.3052.41.20043 | Nodeanalog2VeryLowTrap | Sent to show analog2 went below Very Low analog2 Threshold | ||
| 1.3.6.1.4.1.3052.41.20101 | NodecontactESActiveTrap | Sent to show EventSensor contact is in the alarm state | ||
| 1.3.6.1.4.1.3052.41.20110 | NodetempESHighTrap | Sent to show Temp exceeded High Threshold on an EventSensor | ||
| 1.3.6.1.4.1.3052.41.20111 | NodetempESVeryHighTrap | Sent to show Temp exceeded Very High Threshold on an EventSensor | ||
| 1.3.6.1.4.1.3052.41.20112 | NodetempESLowTrap | Sent to show Temp went below Low Threshold on an EventSensor | ||
| 1.3.6.1.4.1.3052.41.20113 | NodetempESVeryLowTrap | Sent to show Temp went below Very Low Threshold on an EventSensor | ||
| 1.3.6.1.4.1.3052.41.20120 | NodehumidityESHighTrap | Sent to show humidity exceeded High Threshold on an EventSensor | ||
| 1.3.6.1.4.1.3052.41.20121 | NodehumidityESVeryHighTrap | Sent to show humidity exceeded Very High Threshold on an EventSensor | ||
| 1.3.6.1.4.1.3052.41.20122 | NodehumidityESLowTrap | Sent to show humidity went below Low Threshold on an EventSensor | ||
| 1.3.6.1.4.1.3052.41.20123 | NodehumidityESVeryLowTrap | Sent to show humidity went below Very Low Threshold on an EventSensor | ||
| 1.3.6.1.4.1.3052.41.20130 | NodevoltageESHighTrap | Sent to show voltage exceeded High Threshold on an EventSensor | ||
| 1.3.6.1.4.1.3052.41.20131 | NodevoltageESVeryHighTrap | Sent to show voltage exceeded Very High Threshold on an EventSensor | ||
| 1.3.6.1.4.1.3052.41.20132 | NodevoltageESLowTrap | Sent to show voltage went below Low Threshold on an EventSensor | ||
| 1.3.6.1.4.1.3052.41.20133 | NodevoltageESVeryLowTrap | Sent to show voltage went below Very Low Threshold on an EventSensor | ||
| 1.3.6.1.4.1.3052.41.21001 | Nodecontact1NormalTrap | Sent to show Contact 1 is in the normal state | ||
| 1.3.6.1.4.1.3052.41.21002 | Nodecontact2NormalTrap | Sent to show Contact 2 is in the normal state | ||
| 1.3.6.1.4.1.3052.41.21003 | Nodecontact3NormalTrap | Sent to show Contact 3 is in the normal state | ||
| 1.3.6.1.4.1.3052.41.21004 | Nodecontact4NormalTrap | Sent to show Contact 4 is in the normal state | ||
| 1.3.6.1.4.1.3052.41.21005 | Nodecontact5NormalTrap | Sent to show Contact 5 is in the normal state | ||
| 1.3.6.1.4.1.3052.41.21006 | Nodecontact6NormalTrap | Sent to show Contact 6 is in the normal state | ||
| 1.3.6.1.4.1.3052.41.21010 | NodetempNormalTrap | Sent to show Temp went back to Normal range | ||
| 1.3.6.1.4.1.3052.41.21020 | NodehumidityNormalTrap | Sent to show Humidity went back to Normal range | ||
| 1.3.6.1.4.1.3052.41.21030 | Nodeanalog1NormalTrap | Sent to show analog1 went back to Normal range | ||
| 1.3.6.1.4.1.3052.41.21040 | Nodeanalog2NormalTrap | Sent to show analog2 went back to Normal range | ||
| 1.3.6.1.4.1.3052.41.21101 | NodecontactESNormalTrap | Send to show EventSensor contact has returned to normal state | ||
| 1.3.6.1.4.1.3052.41.21110 | NodetempESNormalTrap | Sent to show EventSensor Temp went back to Normal range | ||
| 1.3.6.1.4.1.3052.41.21120 | NodehumidityESNormalTrap | Sent to show EventSensor Humidity went back to Normal range | ||
| 1.3.6.1.4.1.3052.41.21130 | NodevoltageESNormalTrap | Sent to show EventSensor voltage went back to Normal range | ||
| 1.3.6.1.4.1.3052.41.22000 | NodetestTrap | Sent for testing the SNMP interface |