The Report capabilities of the participant, as perceived by the Collector. If the participant can report the Data Source Name as defined in [RFC4710], Section 5.3, then the raqmonPartRepDsrcName bit will be set. If the participant can report the Receiver Name as defined in [RFC4710], Section 5.4, then the raqmonPartRepRecvName bit will be set. If the participant can report the Data Source Port as defined in [RFC4710], Section 5.5, then the raqmonPartRepDsrcPort bit will be set. If the participant can report the Receiver Port as defined in [RFC4710], Section 5.6, then the raqmonPartRepRecvPort bit will be set. If the participant can report the Session Setup Time as defined in [RFC4710], Section 5.7, then the raqmonPartRepSetupTime bit will be set. If the participant can report the Session Setup Delay as defined in [RFC4710], Section 5.8, then the raqmonPartRepSetupDelay bit will be set. If the participant can report the Session Duration as defined in [RFC4710], Section 5.9, then the raqmonPartRepSessionDuration bit will be set. If the participant can report the Setup Status as defined in [RFC4710], Section 5.10, then the raqmonPartRepSetupStatus bit will be set. If the participant can report the Round-Trip End-to-end Network Delay as defined in [RFC4710], Section 5.11, then the raqmonPartRepRTEnd2EndNetDelay bit will be set. If the participant can report the One-way End-to-end Network Delay as defined in [RFC4710], Section 5.12, then the raqmonPartRepOWEnd2EndNetDelay bit will be set. If the participant can report the Application Delay as defined in [RFC4710], Section 5.13, then the raqmonPartApplicationDelay bit will be set. If the participant can report the Inter-Arrival Jitter as defined in [RFC4710], Section 5.14, then the raqmonPartRepIAJitter bit will be set. If the participant can report the IP Packet Delay Variation as defined in [RFC4710], Section 5.15, then the raqmonPartRepIPDV bit will be set. If the participant can report the number of application packets received as defined in [RFC4710], Section 5.16, then the raqmonPartRepRcvdPackets bit will be set. If the participant can report the number of application octets received as defined in [RFC4710], Section 5.17, then the raqmonPartRepRcvdOctets bit will be set. If the participant can report the number of application packets sent as defined in [RFC4710], Section 5.18, then the raqmonPartRepSentPackets bit will be set. If the participant can report the number of application octets sent as defined in [RFC4710], Section 5.19, then the raqmonPartRepSentOctets bit will be set. If the participant can report the number of cumulative packets lost as defined in [RFC4710], Section 5.20, then the raqmonPartRepCumPacketsLoss bit will be set. If the participant can report the fraction of packet loss as defined in [RFC4710], Section 5.21, then the raqmonPartRepFractionPacketsLoss bit will be set. If the participant can report the number of cumulative discards as defined in [RFC4710], Section 5.22, then the raqmonPartRepCumDiscards bit will be set. If the participant can report the fraction of discards as defined in [RFC4710], Section 5.23, then the raqmonPartRepFractionDiscards bit will be set. If the participant can report the Source Payload Type as defined in [RFC4710], Section 5.24, then the raqmonPartRepSrcPayloadType bit will be set. If the participant can report the Destination Payload Type as defined in [RFC4710], Section 5.25, then the raqmonPartRepDestPayloadType bit will be set. If the participant can report the Source Layer 2 Priority as defined in [RFC4710], Section 5.26, then the raqmonPartRepSrcLayer2Priority bit will be set. If the participant can report the Source DSCP/ToS value as defined in [RFC4710], Section 5.27, then the raqmonPartRepSrcToSDscp bit will be set. If the participant can report the Destination Layer 2 Priority as defined in [RFC4710], Section 5.28, then the raqmonPartRepDestLayer2Priority bit will be set. If the participant can report the Destination DSCP/ToS Value as defined in [RFC4710], Section 5.29, then the raqmonPartRepDestToSDscp bit will be set. If the participant can report the CPU utilization as defined in [RFC4710], Section 5.30, then the raqmonPartRepCPU bit will be set. If the participant can report the memory utilization as defined in [RFC4710], Section 5.31, then the raqmonPartRepMemory bit will be set. If the participant can report the Application Name as defined in [RFC4710], Section 5.32, then the raqmonPartRepAppName bit will be set. The capability of reporting of a specific metric does not mandate that the metric must be reported permanently by the data source to the respective collector. Some data sources MAY be configured not to send a metric, or some metrics may not be relevant to the specific application.