MIB Viewer

Search, upload, browse, or download from a database of over 11,000 SNMP MIBs. MIB Viewer lets you look up any MIB object by name, OID, or number, view its syntax, access level, and description, trace its place in the MIB tree, and generate ready-to-run SNMP commands — all in your browser.

What's a MIB?

A MIB (Management Information Base) is a structured document that defines the data a device exposes over SNMP — things like interface counters, system uptime, or CPU load. Each module declares a set of named objects, organized into a tree.

What's SNMP?

SNMP (Simple Network Management Protocol) is how network devices — routers, switches, servers — report status and statistics to monitoring tools. It's the protocol; MIBs are the vocabulary it uses to describe what's being asked for.

What's an OID?

An OID (Object Identifier) is the numeric address of one piece of data in a MIB — a dotted sequence like 1.3.6.1.2.1.1.1, read from the root of a global tree down to one specific object. Names are easier to read; OIDs are what's actually sent over the wire.

Try it: sysDescr (1.3.6.1.2.1.1.1) →

Get started

Search for a MIB or OID above, or pick one from the list on the left.

Have your own MIB file? Drop it on the upload zone in the sidebar (or click to browse) to parse and explore it right away — it stays private to this browser session and isn't added to the shared library.

iso/org/dod/internet/private/enterprises/.6527/.3/.1/.2/.92/.1/.3/tmnxOamPmCfgThrLossFwBwTable/tmnxOamPmCfgThrLossFwBwEntry/tmnxOamPmCfgThrLossAvgFlrClear

tmnxOamPmCfgThrLossAvgFlrClear

OBJECT-TYPE

1.3.6.1.4.1.6527.3.1.2.92.1.3.13.1.4

Access

read-write

Status

current

Source

TIMETRA-OAM-PM-MIB

Sub-identifiers

Description

The value of tmnxOamPmCfgThrLossAvgFlrClear specifies the clear threshold for the average Frame Loss Ratio (FLR). Depending on the specified indices, tmnxOamPmCfgThrLossAvgFlrClear is the clear threshold for: tmnxOamPmStsLossSlmAvgFlrFwd, tmnxOamPmStsLossSlmAvgFlrBwd, tmnxOamPmStsLossLmmAvgFlrFwd, tmnxOamPmStsLossLmmAvgFlrBwd, tmnxOamPmStsLossTwlAvgFlrFwd, or tmnxOamPmStsLossTwlAvgFlrBwd. For example, suppose: 1. OAM-PM loss TCAs are enabled for the 'mi15minutes(2)' measurement interval of the OAM-PM session OAM_PM_Eth_session_1 (using tmnxOamPmCfgMeasIntvlLossTCAs and tmnxOamPmCfgMeasIntvlTCAs). 2. tmnxOamPmCfgThrLossAvgFlrClear is set to 4000 (i.e. 4.000%) for the indices {OAM_PM_Eth_session_1, 'slm(2)', 'forward(1)'}. 3. A previous 15 minute interval belonging to OAM_PM_Eth_session_1's SLM test generated an average FLR Raise TCA for the forward direction (see tmnxOamPmCfgThrLossAvgFlrRaise). The TCA has not been cleared. 4. The just-closed 15-minute interval has an average forward FLR for the forward direction (i.e. tmnxOamPmStsLossSlmAvgFlrFwd) of 4000 (i.e. 4.000%), or less. Then, SROS generates an average FLR Clear TCA (using tmnxOamPmThrClear) at the end of the 15-minute interval, for the forward direction. If tmnxOamPmCfgThrLossAvgFlrRaise > 0 AND tmnxOamPmCfgThrLossAvgFlrClear >= 0, average FLR Clear TCAs can be generated for the specified indices. In this case, the maximum number of average FLR TCAs that will be generated for the specified indices across (for example) two 15 minute intervals is two: Raise and Clear. If tmnxOamPmCfgThrLossAvgFlrRaise > 0 AND tmnxOamPmCfgThrLossAvgFlrClear = -1, no average FLR Clear TCAs will be generated for the specified indices. In this case, the maximum number of average FLR TCAs that will be generated for the specified indices across (for example) two 15 minute intervals is two: Raise and Raise. tmnxOamPmCfgThrLossAvgFlrRaise must be greater than tmnxOamPmCfgThrLossAvgFlrClear. Exception: the combination tmnxOamPmCfgThrLossAvgFlrRaise=-1 and tmnxOamPmCfgThrLossAvgFlrClear=-1 is supported. tmnxOamPmCfgThrLossAvgFlrClear and tmnxOamPmCfgThrLossAvgFlrClear must be set in the same SNMP Set PDU.

Syntax

Integer32 (-1 | 0..99999)