ADTRAN-TAOCTADSL2-MIB
64 objects
The is the MIB module that describes Octal Adsl SMIv2 objects.
Imported Objects
| ADSL-LINE-MIB | adslLineConfProfileName |
| ADTRAN-MIB | adIdentity adMgmt adProducts |
| IF-MIB | ifIndex |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-SMI | 2011 TAS Added adTAOctAdslUsSnrMarginMap IMPORTS MODULE-IDENTITY enterprises Gauge32 Integer32 OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DisplayString |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.664.1.432 | NodeadTAOctAdsl | |||
| 1.3.6.1.4.1.664.1.432.101 | NodeadTAOctAdslalarms | |||
| 1.3.6.1.4.1.664.1.455 | NodeadTAOctAdslwPOTS | |||
| 1.3.6.1.4.1.664.1.752 | NodeadTA5k32pADSL2 | |||
| 1.3.6.1.4.1.664.1.858 | NodeadTA5k24pPOTSADSL2 | |||
| 1.3.6.1.4.1.664.1.1043 | NodeadTA5k32pADSL2int | |||
| 1.3.6.1.4.1.664.2.432 | NodeadTAOctAdslmg | |||
| 1.3.6.1.4.1.664.2.432.1 | NodeadTAOctAdslProv | |||
| 1.3.6.1.4.1.664.2.432.2 | NodeadTAOctAdslProv2 | |||
| 1.3.6.1.4.1.664.2.432.2.1 | TableadTAOctAdslConfProfileExtTable | not-accessible | current | This table contains ADSL line profile configuration information not defined in the adslLineConfProfileTable from the ADSL-LINE-MIB. This includes the line type. |
| 1.3.6.1.4.1.664.2.432.2.1.1 | RowadTAOctAdslConfProfileExtEntry | not-accessible | current | An entry extends the adslLineConfProfileEntry defined in ADSL-LINE-MIB. Each entry corresponds to an ADSL line profile. |
| 1.3.6.1.4.1.664.2.432.2.1.1.1 | ColumnadTAOctAdslConfProfileLineType | read-write | current | This object is used to configure the ADSL physical line type. The object, including enumerations, was taken from the ADSL Extension MIB as this was the only va… |
| 1.3.6.1.4.1.664.2.432.2.1.1.2 | ColumnadTAOctAdslConfProfileServiceMode | read-write | current | This object is used to provision the ADSL physical line service mode. If the line card is a legacy adsl line card, the multiMode option will allow the ATUC to … |
| 1.3.6.1.4.1.664.2.432.2.1.1.3 | ColumnadTAOctAdslConfProfileIndexApplied | read-write | current | This object is used to contain the index of the ADSL template or profile applied to the line. This index is used internally to look up a name or description of… |
| 1.3.6.1.4.1.664.2.432.2.1.1.4 | ColumnadTAOctAdslConfProfileName | read-write | current | This object is used to identify the ADSL template or profile applied to the line by name. |
| 1.3.6.1.4.1.664.2.432.2.1.1.5 | ColumnadTAOctAdslAtucConfProfileInterleaveMinINP | read-write | obsolete | The minimum amount of impulse noise protection, measured in steps of 0.5 DMT symbols (250 microseconds per DMT symbol). This is for the downstream direction. N… |
| 1.3.6.1.4.1.664.2.432.2.1.1.6 | ColumnadTAOctAdslAturConfProfileInterleaveMinINP | read-only | obsolete | The minimum amount of impulse noise protection, measured in steps of 0.5 DMT symbols (250 microseconds per DMT symbol). This is for the upstream direction. |
| 1.3.6.1.4.1.664.2.432.2.1.1.7 | ColumnadTAOctAdslAtucConfProfileInterleaveMinInpRev2 | read-write | current | The minimum amount of impulse noise protection, measured as 0 DMT symbols, 0.5 DMT symbols (250 microseconds per DMT symbol), or 1-16 DMT symbols. This is for … |
| 1.3.6.1.4.1.664.2.432.2.1.1.8 | ColumnadTAOctAdslAturConfProfileInterleaveMinInpRev2 | read-write | current | The minimum amount of impulse noise protection, measured as 0 DMT symbols, 0.5 DMT symbols (250 microseconds per DMT symbol), or 1-16 DMT symbols. This is for … |
| 1.3.6.1.4.1.664.2.432.2.2 | TableadTAOctAdslConfLineTable | not-accessible | current | This table is patterned after the adslLineTable and includes common attributes describing both ends of the line. It applies to all ADSL physical interfaces. AD… |
| 1.3.6.1.4.1.664.2.432.2.2.1 | RowadTAOctAdslConfLineEntry | not-accessible | current | An entry in adTAOctAdslConfLineTable. |
| 1.3.6.1.4.1.664.2.432.2.2.1.1 | ColumnadTAOctAdslHamBandMask | read-write | current | Used to enable/disable the hamband mask for the indexed ADSL port. This object is only valid for lines trained using ADSL2+ service mode |
| 1.3.6.1.4.1.664.2.432.2.2.1.2 | ColumnadTAOctAdslCabinetMode | read-write | current | Used to enable/disable cabinet mode for the indexed ADSL port. The different enable options determine which starting tone to use. This object is only valid for… |
| 1.3.6.1.4.1.664.2.432.2.2.1.3 | ColumnadTAOctAdslPowerThreshold | read-write | current | Used to set the max ADSL tx power. Disabled = no restriction, dBm14 = max tx power 14 dBm, dBm12 = max tx power 12 dBm, dBm10 = max tx power 10 dBm |
| 1.3.6.1.4.1.664.2.432.2.2.1.4 | ColumnadTAOctAdslAtucCarrierMask | read-write | current | Per port Subcarrier Masking. In big endian order, each bit represents a tone from 0 to 63 in the upstream direction. Writing a 1 to a given bit location enable… |
| 1.3.6.1.4.1.664.2.432.2.2.1.5 | ColumnadTAOctAdslAturCarrierMask | read-write | current | Per port Subcarrier Masking. In big endian order, each bit represents a tone from 0 to 511 in the downstream direction. Writing a 1 to a given bit location ena… |
| 1.3.6.1.4.1.664.2.432.4 | NodeadTAOctAdslStatus2 | |||
| 1.3.6.1.4.1.664.2.432.4.1 | TableadTAOctAdslLineTable | not-accessible | current | This table is patterned after the adslLineTable and includes common attributes describing both ends of the line. It applies to all ADSL physical interfaces. AD… |
| 1.3.6.1.4.1.664.2.432.4.1.1 | RowadTAOctAdslLineEntry | not-accessible | current | An entry in adTAOctAdslLineTable. |
| 1.3.6.1.4.1.664.2.432.4.1.1.1 | ColumnadTAOctAdslCurrLinkStatus | read-only | current | The current status of the line (i.e., the link between the ATUC and ATUR). |
| 1.3.6.1.4.1.664.2.432.4.1.1.2 | ColumnadTAOctAdslCurrStandard | read-only | current | The standard governing the link between the ATUC and ATUR. |
| 1.3.6.1.4.1.664.2.432.4.1.1.3 | ColumnadTAOctAdslBitAllocationMap | read-only | current | Per port Bit Allocation Table. 256 nibbles are represented. For each byte bits 4-7 map to the first sub-carrier, bits 0-3 map to the second sub-carrier. |
| 1.3.6.1.4.1.664.2.432.4.1.1.4 | ColumnadTAOctAdslBitAllocationMapGroup2 | read-only | current | Per port Bit Allocation Table tones 256-511. 256 nibbles are represented. For each byte bits 4-7 map to the first sub-carrier, bits 0-3 map to the second sub-c… |
| 1.3.6.1.4.1.664.2.432.4.1.1.5 | ColumnadTAOctAdslUsSnrMarginMap | read-only | current | Per port Signal-to-Noise Ratio table. Each two bytes represents the upstream margin in tenth dB per tone. |
| 1.3.6.1.4.1.664.2.432.4.2 | TableadTAOctAdslAtucPhysTable | not-accessible | current | This table provides one row for each ATUC. Each row contains the Physical Layer Parameters table for that ATUC. ADSL physical interfaces are those ifEntries wh… |
| 1.3.6.1.4.1.664.2.432.4.2.1 | RowadTAOctAdslAtucPhysEntry | not-accessible | current | An entry in the adTAOctAdslAtucPhysTable. |
| 1.3.6.1.4.1.664.2.432.4.2.1.2 | ColumnadTAOctAdslAtucNumParityBytes | read-only | current | Number of Reed-Solomon parity bytes per frame. The value corresponds to the parameter R. This value is only valid when the link is up. |
| 1.3.6.1.4.1.664.2.432.4.2.1.3 | ColumnadTAOctAdslAtucFramesPerCodeword | read-only | current | Hundredth downstream frames per codeword. For G.dmt Mode and G.lite Mode this value corresponds to the data-frames per DMT-symbol. For ADSL2, ADSL2lite, and AD… |
| 1.3.6.1.4.1.664.2.432.4.2.1.4 | ColumnadTAOctAdslAtucInterleavingDepth | read-only | current | Interleaving depth. The value corresponds to the parameter D. This value is only valid when the link is up. |
| 1.3.6.1.4.1.664.2.432.4.3 | TableadTAOctAdslAturPhysTable | not-accessible | current | This table provides one row for each ATUR. Each row contains the Physical Layer Parameters table for that ATUR. ADSL physical interfaces are those ifEntries wh… |
| 1.3.6.1.4.1.664.2.432.4.3.1 | RowadTAOctAdslAturPhysEntry | not-accessible | current | An entry in the adTAOctAdslAturPhysTable. |
| 1.3.6.1.4.1.664.2.432.4.3.1.2 | ColumnadTAOctAdslAturNumParityBytes | read-only | current | Number of Reed-Solomon parity bytes per frame. The value corresponds to the parameter R. This value is only valid when the link is up. |
| 1.3.6.1.4.1.664.2.432.4.3.1.3 | ColumnadTAOctAdslAturFramesPerCodeword | read-only | current | Hundredth upstream frames per codeword. For G.dmt Mode and G.lite Mode this value corresponds to the data-frames per DMT-symbol. For ADSL2, ADSL2lite, and ADSL… |
| 1.3.6.1.4.1.664.2.432.4.3.1.4 | ColumnadTAOctAdslAturInterleavingDepth | read-only | current | Interleaving depth. The value corresponds to the parameter D. This value is only valid when the link is up. |
| 1.3.6.1.4.1.664.2.432.4.3.1.5 | ColumnadTAOctAdslAturCapabilities | read-only | current | The ATUR capabilities is a listing of ADSL properties on a port. It is bit-masked (0 for disabled, 1 for enabled) in the following way: Bit Capability 0 Full R… |
| 1.3.6.1.4.1.664.2.432.4.3.1.6 | ColumnadTAOctAdslAturInvProviderCode | read-only | current | The provider code is a copy of the binary provider code field defined by the PHY[10] and expressed as readable characters. |
| 1.3.6.1.4.1.664.2.432.4.4 | TableadTAOctAdslAtucChanTable | not-accessible | current | This table provides one row for each ATUR channel. ADSL channel interfaces are those ifEntries where ifType is equal to adslInterleave(124) or adslFast(125). |
| 1.3.6.1.4.1.664.2.432.4.4.1 | RowadTAOctAdslAtucChanEntry | not-accessible | current | An entry in the adTAOctAdslAAtucChanTable. |
| 1.3.6.1.4.1.664.2.432.4.4.1.1 | ColumnadTAOctAdslAtucChanINP | read-only | current | Current impulse noise protection on this channel, measured in increments of 0.01 DMT symbols. |
| 1.3.6.1.4.1.664.2.432.4.4.1.2 | ColumnadTAOctAdslAtucRelativeCap | read-only | current | Relative capacity of the ADSL line being used measured by percentage. |
| 1.3.6.1.4.1.664.2.432.4.5 | TableadTAOctAdslAturChanTable | not-accessible | current | This table provides one row for each ATUR channel. ADSL channel interfaces are those ifEntries where ifType is equal to adslInterleave(124) or adslFast(125). |
| 1.3.6.1.4.1.664.2.432.4.5.1 | RowadTAOctAdslAturChanEntry | not-accessible | current | An entry in the adTAOctAdslAAturChanTable. |
| 1.3.6.1.4.1.664.2.432.4.5.1.1 | ColumnadTAOctAdslAturChanINP | read-only | current | Current impulse noise protection on this channel, measured in increments of 0.01 DMT symbols. |
| 1.3.6.1.4.1.664.2.432.4.5.1.2 | ColumnadTAOctAdslAturRelativeCap | read-only | current | Relative capacity of the ADSL line being used measured by percentage. |
| 1.3.6.1.4.1.664.2.432.4.6 | TableadTAOctAdslAtmAtucCellCountTable | not-accessible | current | This table provides one row for each ATM ATUC cell count. |
| 1.3.6.1.4.1.664.2.432.4.6.1 | RowadTAOctAdslAtmAtucCellCountEntry | not-accessible | current | An entry in the AdTAOctAdslAtmAtucCellCountEntry. |
| 1.3.6.1.4.1.664.2.432.4.6.1.1 | ColumnadTAOctAdslAtmAtucCellCount | read-only | current | The ATUC cell count is the sum of all ATM cells from all VCIs on a given port. |
| 1.3.6.1.4.1.664.2.432.4.6.1.2 | ColumnadTAOctAdslAtmAtucIdleCellCount | read-only | current | The ATUC idle cell count is the sum of all idle ATM cells from all VCIs on a given port. |
| 1.3.6.1.4.1.664.2.432.4.6.1.3 | ColumnadTAOctAdslAtmAtucHecErrorCount | read-only | current | The ATUC HEC Error count is the sum of all HEC errors from all VCIs on a given port. |
| 1.3.6.1.4.1.664.2.432.4.7 | TableadTAOctAdslAtmAturCellCountTable | not-accessible | current | This table provides one row for each ATM ATUR cell count. |
| 1.3.6.1.4.1.664.2.432.4.7.1 | RowadTAOctAdslAtmAturCellCountEntry | not-accessible | current | An entry in the AdTAOctAdslAtmAturCellCountEntry. |
| 1.3.6.1.4.1.664.2.432.4.7.1.1 | ColumnadTAOctAdslAtmAturCellCount | read-only | current | The ATUR cell count is the sum of all ATM cells from all VCIs on a given port. |
| 1.3.6.1.4.1.664.2.432.4.7.1.2 | ColumnadTAOctAdslAtmAturIdleCellCount | read-only | current | The ATUR idle cell count is the sum of all idle ATM cells from all VCIs on a given port. |
| 1.3.6.1.4.1.664.6.432 | IdentityadTAOctAdslID | The is the MIB module that describes Octal Adsl SMIv2 objects. |