ALCATEL-IND1-IPV6-MIB
154 objects
This module describes an authoritative enterprise-specific Simple Network Management Protocol (SNMP) Management Information Base (MIB): Propietary IPv6 MIB definitions The right to make changes in specification and other information contained in this document without prior notice is reserved. No liability shall be assumed for any incidental, indirect, special, or consequential damages whatsoever arising from or related to this document or the information contained herein. Vendors, end-users, and other interested parties are granted non-exclusive license to use this specification in connection with management of the products for which it is intended to be used. Copyright (C) 1995-2007 Alcatel-Lucent ALL RIGHTS RESERVED WORLDWIDE
Imported Objects
| ALCATEL-IND1-BASE | softentIND1Ipv6 |
| IF-MIB | InterfaceIndex |
| IPV6-MIB | ipv6IfIndex ipv6RouteEntry |
| IPV6-TC | Ipv6Address Ipv6IfIndexOrZero |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Counter32 IpAddress MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DateAndTime DisplayString PhysAddress RowStatus TEXTUAL-CONVENTION TimeStamp TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.6486.800.1.2.1.29.1 | IdentityalcatelIND1IPv6MIB | This module describes an authoritative enterprise-specific Simple Network Management Protocol (SNMP) Management Information Base (MIB): Propietary IPv6 MIB def… | ||
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1 | NodealcatelIND1IPv6MIBObjects | |||
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.1 | NodealaIPv6Config | |||
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.1.1 | ScalaralaIPv6ClearNeighbors | read-write | current | Clear all non-static entries from the Neighbor table. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.1.2 | ScalaralaIPv6ClearTraffic | read-write | current | Reset all IPv6 traffic counters. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.1.3 | ScalaralaIPv6ClearPMTUTable | read-write | current | Clear the path MTU table. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.1.4 | ScalaralaIPv6PMTUMinLifetime | read-write | current | Set the minimum lifetime for entries in the path MTU table. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.1.5 | ScalaralaIPv6NeighborStaleLifetime | read-write | current | Set the minimum lifetime for neighbor entries in the stale state. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.1.6 | ScalaralaIPv6GlobalID | read-write | current | The global ID used in the creation of local IPv6 unicast addresses (RFC 4193). An explicit value may be specified for the global ID or this object may be set t… |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.1.7 | ScalaralaIPv6ClearRafCounters | read-write | current | Reset all IPv6 Raf counters. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.2 | TablealaIPv6InterfaceTable | not-accessible | current | Table allowing the creation and removal of IPv6 interfaces. The table is indexed by ipv6IfIndex. The value of ipv6IfIndex shall be a four byte value in one of … |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.2.1 | RowalaIPv6InterfaceEntry | not-accessible | current | An IPv6 interface entry. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.2.1.1 | ColumnalaIPv6InterfaceRowStatus | read-create | current | Used to control the addition and removal of IPv6 interfaces. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.2.1.2 | ColumnalaIPv6InterfaceDescription | read-only | current | The IPv6 interface's description. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.2.1.3 | ColumnalaIPv6InterfaceMtu | read-create | current | The IPv6 interface's maximum transmission unit. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.2.1.4 | ColumnalaIPv6InterfaceType | read-only | current | The interface type. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.2.1.5 | ColumnalaIPv6InterfaceAdminStatus | read-create | current | Interface administrative status. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.2.1.6 | ColumnalaIPv6InterfaceSendRouterAdvertisements | read-create | current | Specify whether the router sends periodic router advertisements and responds to router solicitations on the interface. The default value for most interfaces is… |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.2.1.7 | ColumnalaIPv6InterfaceMaxRtrAdvInterval | read-create | current | The maximum time allowed between sending unsolicited multicast router advertisements from the interface. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.2.1.8 | ColumnalaIPv6InterfaceAdvManagedFlag | read-create | current | The TRUE/FALSE value to be placed in the 'Managed address configuration' flag field in router advertisements. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.2.1.9 | ColumnalaIPv6InterfaceAdvOtherConfigFlag | read-create | current | The TRUE/FALSE value to be placed in the 'Other stateful configuration' flag field in router advertisements. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.2.1.10 | ColumnalaIPv6InterfaceAdvReachableTime | read-create | current | The value to be placed in the Reachable Time field in the router advertisements sent over this interface. The value zero means unspecified by this router. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.2.1.11 | ColumnalaIPv6InterfaceAdvRetransTimer | read-create | current | The value to be placed in the Retrans Timer field in the router advertisements sent over this interface. The value zero means unspecified by this router. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.2.1.12 | ColumnalaIPv6InterfaceAdvDefaultLifetime | read-create | current | The value to be placed in the Router Lifetime field in the router advertisements sent over this interface. The value MUST be either zero, 1, or between alaIPv6… |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.2.1.13 | ColumnalaIPv6InterfaceName | read-create | current | The mandatory user-assigned name for the interface. Since the loopback interface is created without user interaction, the name 'loopback' will be automatically… |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.2.1.14 | ColumnalaIPv6InterfaceAdvSendMtu | read-create | current | The TRUE/FALSE value that determines whether the MTU option is sent in Router Advertisements. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.2.1.15 | ColumnalaIPv6InterfaceReachableTime | read-only | current | In the absence of any reachability notification, the amount of time a neighbor reached via this interface will remain in the reachable state before transitioni… |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.2.1.16 | ColumnalaIPv6InterfaceBaseReachableTime | read-create | current | The base value used to compute the reachable time for neighbors reached via this interface. See alaIPv6InterfaceReachableTime above. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.2.1.17 | ColumnalaIPv6InterfaceMinRtrAdvInterval | read-create | current | The minimum time allowed between sending unsolicited multicast router advertisements from the interface. The time must be a minimum of 3 seconds and no more th… |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.2.1.18 | ColumnalaIPv6InterfaceClockSkew | read-create | current | Router Advertisement decrementing timers must be consistent in all Advertisements on the link. The clock skew accounts for link propogation delays and poorly s… |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.2.1.19 | ColumnalaIPv6InterfaceRetransTimer | read-create | current | The amount of time to wait before retransmitting a Neighbor Solicitation during neighbor discovery. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.2.1.20 | ColumnalaIPv6InterfaceDADTransmits | read-create | current | The number of Neighbor Solicitations to send during Duplicate Address Detection. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.2.1.21 | ColumnalaIPv6InterfaceAdvHopLimit | read-create | current | The value placed in the current hop limit field of router advertisements. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.2.1.22 | ColumnalaIPv6InterfaceDADEnable | read-create | current | The TRUE/FALSE value determines whether DAD has to be performed or not. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.3 | NodealaIPv6TunnelConfig | |||
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.3.2 | TablealaIPv6ConfigTunnelTable | not-accessible | current | Table for IPv6 configured tunnels. This table contains the tunnel-specific information extending the corresponding tunnel interface entry in alaIPv6InterfaceTa… |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.3.2.1 | RowalaIPv6ConfigTunnelEntry | not-accessible | current | A entry contains the objects for an IPv6 configured tunnel. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.3.2.1.1 | ColumnalaIPv6ConfigTunnelV4Source | read-create | current | The source IPv4 address for the tunnel. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.3.2.1.2 | ColumnalaIPv6ConfigTunnelV4Dest | read-create | current | The destination IPv4 address for the tunnel. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.4 | TablealaIPv6InterfaceAddressTable | not-accessible | current | Table allowing the creation and removal of IPv6 addresses assigned to interfaces. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.4.1 | RowalaIPv6InterfaceAddressEntry | not-accessible | current | An IPv6 interface address entry. The same link-local address may be assigned to multiple interfaces. A global address may only be assigned to a single interfac… |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.4.1.1 | ColumnalaIPv6InterfaceAddressRowStatus | read-create | current | Used to control the addition and removal of IPv6 interface addresses. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.4.1.2 | ColumnalaIPv6InterfaceAddress | not-accessible | current | An IPv6 address (or prefix for EUI-64 addresses) assigned to the interface. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.4.1.3 | ColumnalaIPv6InterfaceAddressPrefixLength | read-create | current | The number of bits that are significant in the IPv6 address' prefix. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.4.1.4 | ColumnalaIPv6InterfaceAddressAnycastFlag | read-create | current | This object has the value 'true(1)', if this address is an anycast address and the value 'false(2)' otherwise. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.4.1.5 | ColumnalaIPv6InterfaceAddressDADStatus | read-create | current | The status of duplicate address detection for this address. The only value that may be set via SNMP is 'check' when the current status is 'duplicate'. In such … |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.5 | TablealaIPv6InterfaceEUI64AddressTable | not-accessible | current | Table allowing the creation and removal of IPv6 addresses formed by appending an EUI-64 interface identifier to the specified prefix. This table is mainly used… |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.5.1 | RowalaIPv6InterfaceEUI64AddressEntry | not-accessible | current | An IPv6 interface EUI-64 address entry. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.5.1.1 | ColumnalaIPv6InterfaceEUI64AddressRowStatus | read-create | current | Used to control the addition and removal of IPv6 interface EUI-64 addresses. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.5.1.2 | ColumnalaIPv6InterfaceEUI64AddressPrefix | not-accessible | current | The prefix for the EUI-64 address. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.5.1.3 | ColumnalaIPv6InterfaceEUI64AddressPrefixLength | read-create | current | The number of bits that are significant in the IPv6 address' prefix. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.5.1.4 | ColumnalaIPv6InterfaceEUI64AddressIdentifier | read-only | current | The interface's EUI-64 identifier which is combined with the prefix to form the IPv6 address. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.6 | TablealaIPv6NeighborTable | not-accessible | current | The IPv6 neighbor table. Much of this information is available in the RFC-2465 ipv6NetToMediaTable. However, that table does not allow the static configuration… |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.6.1 | RowalaIPv6NeighborEntry | not-accessible | current | Each entry contains one IPv6 address to `physical' address equivalence (a neighbor). |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.6.1.1 | ColumnalaIPv6NeighborNetAddress | not-accessible | current | The neighbor's IPv6 Address. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.6.1.2 | ColumnalaIPv6NeighborPhysAddress | read-create | current | The neighbor's media-dependent `physical' address. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.6.1.3 | ColumnalaIPv6NeighborSlot | read-create | current | The slot used to reach the neighbor. When creating a static neighbor the slot must be specified. On read, a value of zero indicates the slot is not known/not a… |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.6.1.4 | ColumnalaIPv6NeighborPort | read-create | current | The port used to reach the neighbor. When creating a static neighbor the port must be specified. On read, a value of zero indicates the port is not known/not a… |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.6.1.5 | ColumnalaIPv6NeighborType | read-only | current | The type of the mapping. The 'dynamic(2)' type indicates that the IPv6 address to physical addresses mapping has been dynamically resolved using the IPv6 Neigh… |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.6.1.6 | ColumnalaIPv6NeighborState | read-only | deprecated | The Neighbor Unreachability Detection state for the interface when the address mapping in this entry is used. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.6.1.7 | ColumnalaIPv6NeighborLastUpdated | read-only | current | The value of sysUpTime at the time this entry was last updated. If this entry was updated prior to the last re-initialization of the local network management s… |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.6.1.8 | ColumnalaIPv6NeighborRowStatus | read-create | current | Used to control the addition and removal of static entries in the neighbor table. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.6.1.9 | ColumnalaIPv6NeighborLifetime | read-only | current | The remaining time the neighbor will stay in its current state. External events may cause a state change before the expiry of this lifetime. A value of zero in… |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.6.1.10 | ColumnalaIPv6NeighborReachability | read-only | current | The reachability status of the neighbor. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.7 | TablealaIPv6StaticRouteTable | not-accessible | obsolete | This table has been superseded by alaIprmV6StaticRouteTable in ALCATEL-IND1-IPRMV6-MIB. Table allowing the creation and removal of static IPv6 routes. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.7.1 | RowalaIPv6StaticRouteEntry | not-accessible | obsolete | A static route entry. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.7.1.1 | ColumnalaIPv6StaticRouteDest | not-accessible | obsolete | The destination IPv6 address of this static route. This object may not take a Multicast address value. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.7.1.2 | ColumnalaIPv6StaticRoutePfxLength | not-accessible | obsolete | Indicates the prefix length of the destination address. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.7.1.3 | ColumnalaIPv6StaticRouteIfIndex | read-create | obsolete | If the next hop address is a link-local address, this is the ipv6IfIndex value of the interface over which the destination is reached. For all other next hop a… |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.7.1.4 | ColumnalaIPv6StaticRouteNextHop | read-create | obsolete | The IPv6 address of the next hop towards the destination. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.7.1.5 | ColumnalaIPv6StaticRouteMetric | read-create | obsolete | The routing metric for this route. The lower the value, the higher the priority for the static route. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.7.1.6 | ColumnalaIPv6StaticRouteRowStatus | read-create | obsolete | Used to control the addition and removal of static routes. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.8 | TablealaIPv6HostTable | not-accessible | current | Local table mapping host names to IPv6 addresses. This provides the equivalent of /etc/hosts for IPv6. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.8.1 | RowalaIPv6HostEntry | not-accessible | current | A entry maps a host name to an IPv6 address. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.8.1.1 | ColumnalaIPv6HostName | not-accessible | current | A host name to be mapped to an IPv6 address. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.8.1.2 | ColumnalaIPv6HostAddress | not-accessible | current | The IPv6 address mapped to the host name. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.8.1.3 | ColumnalaIPv6HostRowStatus | read-create | current | Allows host name/IPv6 address mappings to be created and deleted in this table. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.9 | TablealaIPv6InterfacePrefixTable | not-accessible | current | Table allowing the creation and removal of IPv6 prefixes to be placed in Prefix Information options in Router Advertisement messages sent from the interface. D… |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.9.1 | RowalaIPv6InterfacePrefixEntry | not-accessible | current | An IPv6 interface prefix entry. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.9.1.1 | ColumnalaIPv6InterfacePrefixRowStatus | read-create | current | Used to control the addition and removal of IPv6 interface prefixes for Router ADvertisement messages. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.9.1.2 | ColumnalaIPv6InterfacePrefix | not-accessible | current | The prefix associated with this interface. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.9.1.3 | ColumnalaIPv6InterfacePrefixLength | not-accessible | current | The length of the prefix in bits. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.9.1.4 | ColumnalaIPv6InterfacePrefixValidLifetime | read-create | current | The value to be placed in the Valid Lifetime in the Prefix Information option, in seconds. The designated value of 4,294,967,295 represents infinity. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.9.1.5 | ColumnalaIPv6InterfacePrefixOnLinkFlag | read-create | current | The value to be placed in the on-link flag (L-bit) field in the Prefix Information option. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.9.1.6 | ColumnalaIPv6InterfacePrefixPreferredLifetime | read-create | current | The value to be placed in the Preferred Lifetime in the Prefix Information option, in seconds. The designated value of 4,294,967,295 represents infinity. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.9.1.7 | ColumnalaIPv6InterfacePrefixAutonomousFlag | read-create | current | The value to be placed in the Autonomous Flag field in the Prefix Information option. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.9.1.8 | ColumnalaIPv6InterfacePrefixSource | read-only | current | The source of this prefix. If configured by management the value will be configured(3). If determined automatically from IPv6 interface address configuration t… |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.9.1.9 | ColumnalaIPv6InterfacePrefixValidLifetimeDecrement | read-create | current | If true, use the remaining seconds derived from alaIPv6InterfacePrefixValidLifetime in the Router Advertisement. If false, use the static value alaIPv6Interfac… |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.9.1.10 | ColumnalaIPv6InterfacePrefixValidLifetimeExpire | read-create | current | The date and time when the advertised prefix Valid Lifetime expires. To use this value, alaIPv6InterfaceValidLifetimeDecrement must be set to true. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.9.1.11 | ColumnalaIPv6InterfacePrefixPreferredLifetimeDecrement | read-create | current | If true, use the remaining seconds derived from alaIPv6InterfacePrefixPreferredLifetime in the Router Advertisement. If false, use the static value alaIPv6Inte… |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.9.1.12 | ColumnalaIPv6InterfacePrefixPreferredLifetimeExpire | read-create | current | The date and time when the advertised prefix Preferred Lifetime expires. To use this value, alaIPv6InterfacePreferredLifetimeDecrement must be set to true. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.10 | TablealaIPv6PMTUTable | not-accessible | current | Table allowing the retrieval of the known IPv6 path MTU value. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.10.1 | RowalaIPv6PMTUEntry | not-accessible | current | An IPv6 path MTU entry. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.10.1.1 | ColumnalaIPv6PMTUDest | not-accessible | current | The destination address of the IPv6 path. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.10.1.2 | ColumnalaIPv6PMTU | read-only | current | The path's MTU. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.10.1.3 | ColumnalaIPv6PMTUExpire | read-only | current | The minimum time remaining before the PMTU entry is removed from the table. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.10.1.4 | ColumnalaIPv6PMTUHits | read-only | current | The number of times the path MTU entry has been used. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.10.1.5 | ColumnalaIPv6PMTUUpdates | read-only | current | The number of times the path MTU entry has been updated. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.11 | TablealaIPv6RouteFlagsTable | not-accessible | current | Table allowing the retrieval of the flags for IPv6 route entries. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.11.1 | RowalaIPv6RouteFlagsEntry | not-accessible | current | An IPV6 route flags entry. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.11.1.1 | ColumnalaIPv6RouteFlagsUp | read-only | current | True if the Up (U) flag is set on the route. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.11.1.2 | ColumnalaIPv6RouteFlagsGateway | read-only | current | True if the Gateway (G) flag is set on the route. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.11.1.3 | ColumnalaIPv6RouteFlagsHost | read-only | current | True if the Host (H) flag is set on the route. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.11.1.4 | ColumnalaIPv6RouteFlagsStatic | read-only | current | True if the Static (S) flag is set on the route. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.11.1.5 | ColumnalaIPv6RouteFlagsCloneable | read-only | current | True if the Cloneable (C) flag is set on the route. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.11.1.6 | ColumnalaIPv6RouteFlagsDiscard | read-only | current | True if the Discard/Blackhole (B) flag is set on the route. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.11.1.7 | ColumnalaIPv6RouteFlagsECMP | read-only | current | True if the ECMP (E) flag is set on the route. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.12 | NodealcatelIND1IPv6Traps | |||
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.12.0 | NodealcatelIND1IPv6TrapsRoot | |||
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.12.0.1 | NotificationndpMaxLimitReached | current | This notification is generated when hardware table has reached supported Maximum entries. OS6400 will not generate new ARP request for new nexthops | |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.13 | TablealaIPv6LocalUnicastTable | not-accessible | current | Table allowing the creation and removal of local IPv6 unicast addresses (RFC 4193) on an interface. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.13.1 | RowalaIPv6LocalUnicastEntry | not-accessible | current | An local unicast IPv6 address entry. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.13.1.1 | ColumnalaIPv6LocalUnicastGlobalID | not-accessible | current | The global ID portion of the local IPv6 unicast address. Leave the value as all zero when adding a new addres to use the alaIPv6GlobalID value. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.13.1.2 | ColumnalaIPv6LocalUnicastSubnetID | not-accessible | current | The subnet ID portion of the local IPv6 unicast address. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.13.1.3 | ColumnalaIPv6LocalUnicastInterfaceID | not-accessible | current | The interface identifier portion of the local IPv6 unicast address. When alaIPv6LocalUnicastEUI64 is true(1) the value of this object should be all zero. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.13.1.4 | ColumnalaIPv6LocalUnicastPrefixLength | read-create | current | The number of bits that are significant in the IPv6 address prefix. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.13.1.5 | ColumnalaIPv6LocalUnicastEUI64 | read-create | current | If true(1) the interface identifier is formed from an automatically generated EUI-64 value. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.13.1.6 | ColumnalaIPv6LocalUnicastRowStatus | read-create | current | Used to control the addition and removal of local IPv6 unicast addresses. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.14 | TablealaIpv6RafVlanTable | not-accessible | current | A table that contains the IPV6 RAF Vlans |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.14.1 | RowalaIpv6RafVlanEntry | not-accessible | current | The list of VLANs for which RAF is enabled |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.14.1.1 | ColumnalaIpv6RafVlan | not-accessible | current | The VLAN ID for which RAF is enabled. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.14.1.2 | ColumnalaIpv6RafVlanRowStatus | read-create | current | The status of this table entry. The supported value for set are createAndGo (4) and destroy(6), to add or remove a binding |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.14.1.3 | ColumnalaIpv6RafVlanActiveStatus | read-only | current | The TRUE/FALSE value to specify the status of RA-Filter. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.15 | TablealaIpv6RafPortTable | not-accessible | current | A table that contains the IPV6 RAF ports ports for a vlan |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.15.1 | RowalaIpv6RafPortEntry | not-accessible | current | The list of ports of VLAN for which RAF is enabled |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.15.1.1 | ColumnalaIpv6RafPortVlan | not-accessible | current | The VLAN ID for which RAF is enabled. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.15.1.2 | ColumnalaIpv6RafPortIfIndex | not-accessible | current | The IfIndex of this UNI Port. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.15.1.3 | ColumnalaIpv6RafPortRowStatus | read-create | current | The status of this table entry. The supported value for set are createAndGo (4) and destroy(6), to add or remove a trusted port from vlan |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.15.1.4 | ColumnalaIpv6RafPortActiveStatus | read-only | current | The TRUE/FALSE value to specify the status of RA-Filter Port. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.16 | TablealaIpv6RafCounterStatsTable | not-accessible | current | A table that contains the IPV6 RAF Counter statistics |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.16.1 | RowalaIpv6RafCounterStatsEntry | not-accessible | current | The list of NI's for which RAF counter statistics is displayed |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.16.1.1 | ColumnalaIpv6RafNi | not-accessible | current | The NI for which RAF is enabled and is UP. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.1.16.1.2 | ColumnalaIpv6RafUntrustedPktCnt | read-only | current | The Untrusted packets count for Ra-filter enabled NI's. |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.2 | NodealcatelIND1IPv6MIBConformance | |||
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.2.1 | NodealcatelIND1IPv6MIBCompliances | |||
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.2.1.1 | CompliancealaIPv6Compliance | current | The compliance statement for switches with Alcatel IPv6 stack and implementing ALCATEL-IND1-IPV6-MIB. | |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.2.2 | NodealcatelIND1IPv6MIBGroups | |||
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.2.2.1 | GroupalaIPv6TunnelConfigGroup | current | A collection of objects to support management of Alcatel IPv6 tunneling. | |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.2.2.2 | GroupalaIPv6ConfigGroup | current | A collection of objects to support management of configuration parameters of Alcatel IPv6 stack. | |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.2.2.3 | GroupalaIPv6NeighborGroup | current | A collection of objects to support management of IPv6 neighbors. | |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.2.2.4 | GroupalaIPv6StaticRouteGroup | obsolete | A collection of objects to support management of IPv6 static routes. | |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.2.2.5 | GroupalaIPv6InterfaceGroup | current | A collection of objects to support management of IPv6 interfaces. | |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.2.2.6 | GroupalaIPv6InterfaceAddressGroup | current | A collection of objects to support management of IPv6 addresses assigned to interfaces. | |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.2.2.7 | GroupalaIPv6InterfaceEUI64AddressGroup | current | A collection of objects to support management of IPv6 EUI-64 addresses assigned to interfaces. | |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.2.2.8 | GroupalaIPv6InterfacePrefixGroup | current | A collection of objects to support management of IPv6 prefixes assigned to interfaces. | |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.2.2.9 | GroupalaIPv6PMTUGroup | current | A collection of objects to support management of IPv6 path MTUs. | |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.2.2.10 | GroupalaIPv6RouteFlagsGroup | current | A collection of objects to support management of IPv6 route flags. | |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.2.2.11 | GroupalaIPv6LocalUnicastGroup | current | A collection of objects to support management of local IPv6 unicast addresses (RFC 4193). | |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.2.2.12 | GroupalaIPv6HostGroup | current | A entry maps a host name to an IPv6 address. | |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.2.2.13 | GroupalcatelIND1IPv6TrapsGroup | current | This notification is generated when hardware table has reached supported Maximum entries. | |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.2.2.14 | GroupalaIpv6RafVlanGroup | current | A collection of objects to support management of IPv6 RAF | |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.2.2.15 | GroupalaIpv6RafPortGroup | current | A collection of objects to support management of local IPv6 unicast addresses (RFC 4193). | |
| 1.3.6.1.4.1.6486.800.1.2.1.29.1.2.2.16 | GroupalaIpv6RafCounterStatsGroup | current | A collection of objects to support management of IPv6 RAF |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| AlaIPv6AddressPrefix | OCTET STRING (SIZE (8)) | current | A data type for the 8 byte IPv6 prefixes for EUI-64 addresses |