ARRIS-CM-DEVICE-MIB
137 objects
This MIB module supplies the basic proprietary (ARRIS-specific) management objects for ARRIS Cable Modem (CM) devices.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.4115.1.3.1 | IdentityarrisCmDevMib | This MIB module supplies the basic proprietary (ARRIS-specific) management objects for ARRIS Cable Modem (CM) devices. | ||
| 1.3.6.1.4.1.4115.1.3.1.1 | NodearrisCmDevMibObjects | |||
| 1.3.6.1.4.1.4115.1.3.1.1.1 | NodearrisCmDevBase | |||
| 1.3.6.1.4.1.4115.1.3.1.1.1.1 | ScalararrisCmDevWanIsolationState | read-write | current | The object controls the state of WAN Isolation. The meaning of the state is as follows: off-InActiveMode(1) - Data traffic passes freely between the home user'… |
| 1.3.6.1.4.1.4115.1.3.1.1.1.2 | ScalararrisCmDevSwImageName | read-only | current | The name of the software image currently operating on this device. |
| 1.3.6.1.4.1.4115.1.3.1.1.1.3 | ScalararrisCmDevSwImageBuildTime | read-only | current | The build date and time of the software image currently operating on this device. |
| 1.3.6.1.4.1.4115.1.3.1.1.1.4 | ScalararrisCmDevRangeDelay | read-only | current | Reports range delay value in use by the modem. This value can be adjusted by the CMTS through the periodic ranging process. This MIB is provided to enable MSOs… |
| 1.3.6.1.4.1.4115.1.3.1.1.1.5 | NodearrisCmDevDhcp | |||
| 1.3.6.1.4.1.4115.1.3.1.1.1.5.1 | NodearrisCmDevDhcpCmParameters | |||
| 1.3.6.1.4.1.4115.1.3.1.1.1.5.1.1 | ScalararrisCmDevDhcpCmIpAddr | read-only | deprecated | This object is deprecated. See arrisCmDevDhcpCmIpAddrV6 for its replacement. This displays the currently leased IP address . |
| 1.3.6.1.4.1.4115.1.3.1.1.1.5.1.2 | ScalararrisCmDevDhcpCmSubNetMask | read-only | current | This displays the current IP subnet mask in use. |
| 1.3.6.1.4.1.4115.1.3.1.1.1.5.1.3 | ScalararrisCmDevDhcpCmGatewayIpAddr | read-only | current | This displays the current IP gateway address in use. |
| 1.3.6.1.4.1.4115.1.3.1.1.1.5.1.4 | ScalararrisCmDevDhcpCmConfigFile | read-only | current | This displays the CM configuration file to be retrieved. |
| 1.3.6.1.4.1.4115.1.3.1.1.1.5.1.5 | ScalararrisCmDevDhcpIpMode | read-only | current | This displays the current DHCP IP address mode,ipv4 or ipv6. |
| 1.3.6.1.4.1.4115.1.3.1.1.1.5.1.6 | ScalararrisCmDevDhcpCmIpAddrV6 | read-only | current | This displays the currently leased IPv6 address . |
| 1.3.6.1.4.1.4115.1.3.1.1.1.5.1.7 | ScalararrisCmDevDhcpCmSubNetMaskV6 | read-only | current | This displays the current IPv6 subnet mask in use. |
| 1.3.6.1.4.1.4115.1.3.1.1.1.5.1.8 | ScalararrisCmDevDhcpCmGatewayIpAddrV6 | read-only | current | This displays the current IPv6 gateway address in use. |
| 1.3.6.1.4.1.4115.1.3.1.1.1.5.2 | NodearrisCmDevDhcpSvrParameters | |||
| 1.3.6.1.4.1.4115.1.3.1.1.1.5.2.1 | ScalararrisCmDevDhcpState | read-only | current | This displays the current Dhcp state of the CM. |
| 1.3.6.1.4.1.4115.1.3.1.1.1.5.2.2 | ScalararrisCmDevDhcpPrimaryDhcpServerIpAddr | read-only | current | This displays the primary Dhcp server address. |
| 1.3.6.1.4.1.4115.1.3.1.1.1.5.2.3 | ScalararrisCmDevDhcpTftpSvrIpAddr | read-only | current | This displays the current Tftp Server IP address in use. |
| 1.3.6.1.4.1.4115.1.3.1.1.1.5.2.4 | ScalararrisCmDevDhcpTimeSvrIpAddr | read-only | current | This displays the current Time server IP address in use. |
| 1.3.6.1.4.1.4115.1.3.1.1.1.5.2.5 | ScalararrisCmDevDhcpCmTimeOffset | read-only | current | This displays the current Time offset being used by the CM. |
| 1.3.6.1.4.1.4115.1.3.1.1.1.5.2.6 | ScalararrisCmDevDhcpPrimaryTeleDhcpSvr | read-only | current | This displays the current Time offset being used by the CM. |
| 1.3.6.1.4.1.4115.1.3.1.1.1.5.2.7 | ScalararrisCmDevDhcpSecondaryTeleDhcpSvr | read-only | current | This displays the current Time offset being used by the CM. |
| 1.3.6.1.4.1.4115.1.3.1.1.1.5.2.8 | ScalararrisCmDevDhcpPrimaryDhcpServerIpAddrV6 | read-only | current | This displays the primary Dhcp server IPv6 address. |
| 1.3.6.1.4.1.4115.1.3.1.1.1.5.2.9 | ScalararrisCmDevDhcpTftpSvrIpAddrV6 | read-only | current | This displays the current Tftp Server IPv6 address in use. |
| 1.3.6.1.4.1.4115.1.3.1.1.1.5.2.10 | ScalararrisCmDevDhcpTimeSvrIpAddrV6 | read-only | current | This displays the current Time server IPv6 address in use. |
| 1.3.6.1.4.1.4115.1.3.1.1.1.5.3 | NodearrisCmDevDhcpLeaseParameters | |||
| 1.3.6.1.4.1.4115.1.3.1.1.1.5.3.1 | ScalararrisCmDevDhcpOfferedLeaseTime | read-only | current | This displays the Offered IP Lease time expressed in seconds. |
| 1.3.6.1.4.1.4115.1.3.1.1.1.5.3.2 | ScalararrisCmDevDhcpLeaseTimeRemaining | read-only | current | This displays the Remaining IP Lease time expressed in seconds. |
| 1.3.6.1.4.1.4115.1.3.1.1.1.5.3.3 | ScalararrisCmDevDhcpTimeUntilRenew | read-only | current | This displays the current time remaining before the MTA starts the lease renewal process. This time is expressed in seconds. |
| 1.3.6.1.4.1.4115.1.3.1.1.1.5.3.4 | ScalararrisCmDevDhcpTimeUntilRebind | read-only | current | This displays the current time remaining before the CM starts the lease rebinding process. This time is expressed in seconds. |
| 1.3.6.1.4.1.4115.1.3.1.1.1.6 | ScalararrisCmDevRegistrationState | read-only | current | The last registration step completed as the E-MTA provisioning progresses through the DOCSIS/PacketCable registration and provisioning steps. |
| 1.3.6.1.4.1.4115.1.3.1.1.1.7 | NodearrisCmDevResetReasonLog | |||
| 1.3.6.1.4.1.4115.1.3.1.1.1.7.1 | ScalararrisCmDevLastHwResetReason | read-only | current | The last reset reason retrieved from the actual processor HW. This reason is used to determine if the HW or FW caused the reset. The majority of the time this … |
| 1.3.6.1.4.1.4115.1.3.1.1.1.7.2 | TablearrisCmDevResetReasonLogTable | not-accessible | current | This table contains the last 10 reset reasons. |
| 1.3.6.1.4.1.4115.1.3.1.1.1.7.2.1 | RowarrisCmDevResetReasonLogEntry | not-accessible | current | This table contains the last 10 reset reasons. |
| 1.3.6.1.4.1.4115.1.3.1.1.1.7.2.1.1 | ColumnarrisCmDevResetReasonLogIndex | not-accessible | current | Index used to report log reasons. |
| 1.3.6.1.4.1.4115.1.3.1.1.1.7.2.1.2 | ColumnarrisCmDevResetReasonLogText | read-only | current | The reported reset reason log text. |
| 1.3.6.1.4.1.4115.1.3.1.1.1.7.3 | ScalararrisCmDevResetReasonLogDisable | read-write | current | Disables the storage of the reset reasons to the Reset Reasons LOG table thus saving writes to NVM. This will default to false(2) allowing the logging to occur… |
| 1.3.6.1.4.1.4115.1.3.1.1.1.8 | ScalararrisCmDevDualModeDiscoveredMarket | read-only | current | This MIB object reports the Dual Mode Discovered Market from the CM. |
| 1.3.6.1.4.1.4115.1.3.1.1.2 | NodearrisCmDevCmSetup | |||
| 1.3.6.1.4.1.4115.1.3.1.1.2.2 | NodearrisCmDevPermanentSetup | |||
| 1.3.6.1.4.1.4115.1.3.1.1.2.3 | NodearrisCmDevOperationalSetup | |||
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.2 | ScalararrisCmDevProvMethodIndicator | read-write | deprecated | Indicates the method used to provision the device. This object should only be changed by the configuration file. The following provisioning methods are support… |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.3 | ScalararrisCmDevEnableDocsis20 | read-write | current | This object is used to enable/disable DOCSIS 2.0 operation mode. This object is stored into NVRAM and will be operational after the next reboot of the device. … |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.4 | ScalararrisCmDevModemFeatureSwitch | read-write | current | This object is used to enable proprietary features of the Arris cable modem. From left to right, the specified bit indicates whether or not the corresponding m… |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.5 | NodearrisCmDevHttp | |||
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.5.3 | ScalararrisCmDevHttpLanAccess | read-write | current | Controls the level of LAN-side HTTP access to the modem. The levels are described as: off(1) - LAN-side HTTP access is denied. basic(2) - allow basic HTTP acce… |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.5.4 | ScalararrisCmDevHttpWanAccess | read-write | current | Controls the level of WAN-side HTTP access to the modem. The levels are described as: off(1) - WAN-side HTTP access is denied. basic(2) - allow basic HTTP acce… |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.5.5 | ScalararrisCmDevHttpClientSeed | read-write | current | The DES encoded seed to generate the password for access to the HTTP Advanced Pages. When read, this object will return a zero-length string. |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.5.6 | ScalararrisCmDevHttpAdvLink | read-write | current | This object provides the ability to show or hide the ADV link on the HTTP Web Page. |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.6 | NodearrisCmDevTurboDoxConfiguration | |||
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.6.3 | ScalararrisCmDevTurboDoxEnable | read-write | current | This object is used to enable/disable TurboDox operation. Set to true(1) to enable TurboDox operation mode. Set to false(2) to disable TurboDox operation mode.… |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.6.4 | ScalararrisCmDevTurboDoxDeleteTimer | read-write | current | This object represents the TCP session delete timeout value. This object can only be changed by the configuration file. The default value for this object is 15. |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.6.5 | ScalararrisCmDevTurboDoxSlowStartTimer | read-write | current | This object represents the TCP slow start timeout value. This object can only be changed by the configuration file. The default value for this object is 10. |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.6.6 | ScalararrisCmDevTurboDoxVersion | read-only | current | This object indicates the TurboDox version. |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.7 | ScalararrisCmDevDhcpServerEnable | read-write | current | This object is used to enable/disable the local DHCP Server. As long as the CM is not operational, the local DHCP Server is working if enabled. Set to true(1) … |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.8 | ScalararrisCmDevDhcpServerState | read-only | current | Indicates the current state of the local DHCP Server. |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.9 | NodearrisCmDevScanningSetup | |||
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.9.1 | TablearrisCmDevPresetFrequencyTable | not-accessible | current | This table contains all the MIB variables required for Preset Frequency Scanning. |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.9.1.1 | RowarrisCmDevPresetFrequencyEntry | not-accessible | current | This table contains all the MIB variables required for Preset Frequency Scanning. |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.9.1.1.1 | ColumnarrisCmDevPresetFrequencyIndex | not-accessible | current | Index used to order the arrisCmDevPresetFrequencyTable entries. |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.9.1.1.2 | ColumnarrisCmDevPresetFrequency | read-write | current | Preset Frequency used in scanning. This value should be entered in Hz (Hertz). |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.9.2 | ScalararrisCmDevClearPresetFrequencies | read-write | current | If set to True(1), the device will erase all the Preset frequencies. When read False(2) will always be returned |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.9.3 | ScalararrisCmDevClearCachedFrequencies | read-write | current | If set to True(1), the device will erase all the Cached frequencies. When read False(2) will always be returned |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.10 | ScalararrisCmDevReportLevelsMasterOff | read-write | current | If set to True(1) all Report Levels and Debug Tracing will be turned Off, and Logits Logs will return to thier default values. When this object is read False(2… |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.11 | ScalararrisCmDevEraseLogBlock | read-write | current | If set to True(1) this MIB object will erase the Arris log block. When this object is read False(2) will be returned. |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.12 | ScalararrisCmDevEnableDocsis10Plus | read-write | current | This object is used to enable/disable DOCSIS 1.0+ operational mode. This setting is stored into NVRAM and therefore will survive resets. Set to true(1) to enab… |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.13 | ScalararrisCmDevEnableOption177 | read-write | current | This object is used to enable/disable sending only DHCP option 177 rather than sending both option 122 and 177. This setting is stored into NVRAM and therefore… |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.14 | ScalararrisCmDevEnableLoggingPersistence | read-write | current | This object is used to enable/disable the telnet logging persistence feature. This setting is stored into NVRAM and therefore will survive resets. Set to true(… |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.15 | ScalararrisCmDevModemFeatureSwitch2 | read-write | current | This object is used to enable proprietary features of the Arris cable modem. From left to right, the specified bit indicates whether or not the corresponding m… |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.16 | ScalararrisCmDevDocsQosParamSetActiveTimeout | read-write | current | Send QOS Timeout parameter to CMTS for upstream flow IF feature switch for DSX DQOS is enabled AND the value of this MIB is set to a value other than the defau… |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.17 | ScalararrisCmDevCLITimeout | read-write | current | Max time that a telnet/SSH session can be idle before it is terminated. Range is 0-1440 minutes, where 0 disables the timer completely. |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.18 | ScalararrisCmDevTODSyncTimeOut | read-write | current | This value determines the interval between the TOD sync operations. Range is 0-4320 hours, where 0 disables the sync completely. This value sets the interval s… |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.19 | ScalararrisCmDevDhcpNoSvcImpact | read-write | current | This object is used to enable/disable the DHCP RENEW interruption feature. During an active call DHCP lease renewal will be stalled until all endpoints are onh… |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.20 | ScalararrisCmDevDhcpOption51Override | read-write | current | Enable or Disable the inclusion of DHCP option code 51 in the DHCP REQUEST message. A value of off(1) will cause DHCP option code 51 to be included in the DHCP… |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.21 | ScalararrisCmDevDEAControl | read-write | current | Turn on or off the DEA algorithm. The default value is on(1). |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.22 | ScalararrisCmDevSinglePasswd | read-write | current | The encoded password for single password access to the CLI & HTTP Advanced Pages. When read, this object will return a zero-length string. |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.23 | ScalararrisCmDevTelnetEnable | read-write | current | Used to enable/disable Telnet access. TempEnable enables Telnet for one session only. For Telnet to be enabled, arrisCmDevTelnetAllow must also be set to 'allo… |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.24 | ScalararrisCmDevSSHEnable | read-write | current | Used to enable/disable SSH access. TempEnable enables SSH for one session only. For SSH to be enabled, arrisCmDevSSHAllow must also be set to 'allow'. |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.25 | ScalararrisCmDevTelnetAllow | read-write | current | Used to allow/inhibit Telnet access. For Telnet to be allowed, arrisCmDevTelnetEnable must also be set to 'enable'. |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.26 | ScalararrisCmDevSSHAllow | read-write | current | Used to allow/inhibit SSH access. For SSH to be allowed, arrisCmDevSSHEnable must also be set to 'enable'. |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.27 | ScalararrisCmDevWirelessRegion | read-write | current | This value specifies the region that the modem operates in so it can determine the range of channels which may be selected by the user for 802.11 operation. Th… |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.28 | ScalararrisCmDevRouterMode | read-write | current | This value specifies what operating mode should be used by the embedded router in Touchstone products that include a router. If not specified, the router will … |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.29 | ScalararrisCmDevEnableDHCPLog | read-write | current | Used to enable/disable CM DHCP Logging. |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.30 | ScalararrisCmDevClearDHCPLog | read-write | current | Used to Clear the CM DHCP Logs. |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.31 | ScalararrisCmDevRouterLanIpAddr | read-write | current | This is the current Router Lan IP address. |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.32 | ScalararrisCmDevRouterLanSubNetMask | read-write | current | This is the current Router Lan Subnet Mask. |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.33 | ScalararrisCmDevRouterLanEnable | read-write | current | Used to enable/disable Router Lan. |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.34 | ScalararrisCmDevRouterLanReset | read-write | current | Setting this object to true(1) will reset the Router Lan Setting this object to false(2) will do nothing. Reading this object always returns false(2). |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.35 | ScalararrisCmDevRipTransmitStatus | read-only | current | Active when the RIP on puma is actively transmitting RIP updates. In order for arrisCmDevRipTransmitStatus to be active, arrisCmDevRouterLanEnable must be enab… |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.36 | ScalararrisCmDevDectReset | read-write | current | Setting this object to true(1) will reset the Dect module Setting this object to false(2) will do nothing. Reading this object always returns false(2). |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.37 | ScalararrisCmDevTftpBlkSize | read-write | current | This object is used for the TFTP Blocksize Option (RFC 2348). Valid values range between 32 and 1448 octets, inclusive. Setting this object to 0(default) disab… |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.38 | ScalararrisCmDevTODTimeOffset | read-write | current | This mib is used to update CM TOD time offset. The range of the offset is -12*60*60(-43200) to 13*60*60(46800) in seconds. 13 is Daylight Savings Time in the +… |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.39 | ScalararrisCmDevWrmProvServer | read-write | current | This object is used to store the TFTP Server Name for the WRM card if it cannot be included in the DHCP Offer. |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.40 | ScalararrisCmDevWrmProvFileName | read-write | current | This object is used to store the Bootfile name for the WRM card if it cannot be included in the DHCP Offer. |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.41 | ScalararrisCmDevDSTPolicy | read-write | current | This object is used to get and set the daylight saving time policy. This parameter is a rule with two fields separated by semicolon (;) as shown below: start=<… |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.42 | ScalararrisCmDevRestoreNvmFactoryDefault | read-write | current | Setting this object to true(1) will reset the NVM to default values: Setting this object to false(2) will do nothing. Reading this object always returns false(… |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.43 | ScalararrisCmDevWrmProvFile | read-write | current | This object is used to store the Bootfile for the WRM card if it cannot be provisioned by the usual TFTP server. |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.44 | ScalararrisCmDevUGSTxQueueSize | read-write | current | Controls the permitted depth of HW upstream buffer queue for UGS service flows. Packets are discarded if depth of queue exceeds this setting. A setting of disa… |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.45 | ScalararrisCmDevUniqueConfigFileEnable | read-write | current | Used to enable/disable downloading the ARRIS unique config file. Default value is set to 'disable'. This MIB can only be set via the CM config file, but sets w… |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.46 | ScalararrisCmDevUniqueConfigFileServerAddrType | read-write | current | This object is used to get and set the IP address mode of the TFTP server for the ARRIS unique config file. This MIB can only be set via the CM config file, an… |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.47 | ScalararrisCmDevUniqueConfigFileServerAddr | read-write | current | This object is used to get and set the TFTP server address that will be used to download the ARRIS unique config file. This MIB can only be set via the CM conf… |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.48 | ScalararrisCmDevSetupMddIpModeOverride | read-write | current | This object is used to override the IP Mode TLV in the MDD message. 0 = use the MDD value 1 = IPv4 Only 2 = IPv6 Only 3 = Alternate (APM) 4 = Dual-stack (DPM) |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.49 | ScalararrisCmDevWrmProvFileNameMacEnable | read-write | current | When Enabled in the CM configuration file, and the MIB value of arrisCmDevWrmProvFileName is blank, the CM would generate the MIB rrisCmDevWrmProvFileName to b… |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.50 | ScalararrisCmDevTftpMtaIpOverride | read-write | current | This object is used to store the TFTP Server IP Address and it will override the DHCP Offer. |
| 1.3.6.1.4.1.4115.1.3.1.1.2.3.51 | ScalararrisCmDevEthernetPower | read-write | current | off(0) - power off Ethernet interface. on(1) - power on Ethernet interface default(2) - power off Ethernet interface for CM600, power on Ethernet interface for… |
| 1.3.6.1.4.1.4115.1.3.1.1.2.4 | NodearrisCmDevSalesSetup | |||
| 1.3.6.1.4.1.4115.1.3.1.1.3 | NodearrisCmDevCmTest | |||
| 1.3.6.1.4.1.4115.1.3.1.1.3.2 | NodearrisCmDevManufacturingTest | |||
| 1.3.6.1.4.1.4115.1.3.1.1.3.3 | NodearrisCmDevOperationalTest | |||
| 1.3.6.1.4.1.4115.1.3.1.1.4 | NodearrisCmDevSoftware | |||
| 1.3.6.1.4.1.4115.1.3.1.1.4.1 | TablearrisCmDevSwTable | not-accessible | current | This table contains all the MIB variables required for the Touchstone Software Upgrade System. |
| 1.3.6.1.4.1.4115.1.3.1.1.4.1.1 | RowarrisCmDevSwEntry | not-accessible | current | This table contains all the MIB variables required for the Touchstone Software Upgrade System. |
| 1.3.6.1.4.1.4115.1.3.1.1.4.1.1.1 | ColumnarrisCmDevSwIndex | not-accessible | current | Index used to order the arrisCmDevSwTable entries. |
| 1.3.6.1.4.1.4115.1.3.1.1.4.1.1.2 | ColumnarrisCmDevSwCustomerLoadId | read-write | current | Custom string to identify Touchstone Software Upgrade load lineups. (OPTIONAL) |
| 1.3.6.1.4.1.4115.1.3.1.1.4.1.1.3 | ColumnarrisCmDevSwHwModel | read-write | current | HW Model of Touchstone product to be downloaded. (REQUIRED) |
| 1.3.6.1.4.1.4115.1.3.1.1.4.1.1.4 | ColumnarrisCmDevSwHwRev | read-write | current | HW Revision of Touchstone product to be downloaded. (OPTIONAL) |
| 1.3.6.1.4.1.4115.1.3.1.1.4.1.1.5 | ColumnarrisCmDevSwServer | read-write | deprecated | The address of the TFTP server used for software upgrades. If the TFTP server is unknown or is a non-IPv4 address, return 0.0.0.0. This object is deprecated. S… |
| 1.3.6.1.4.1.4115.1.3.1.1.4.1.1.6 | ColumnarrisCmDevSwFilename | read-write | current | The file name of the Touchstone software image to be loaded on to this device. (REQUIRED) |
| 1.3.6.1.4.1.4115.1.3.1.1.4.1.1.8 | ColumnarrisCmDevSwServerAddressType | read-write | current | This get/set IP address mode of the server for Touchstone Software Upgrading,ipv4 or ipv6. (REQUIRED) |
| 1.3.6.1.4.1.4115.1.3.1.1.4.1.1.9 | ColumnarrisCmDevSwServerAddress | read-write | current | This object is used to get/set the IPv6 or IPv4 TFTP server address that will be used to download the image. A set of this object to an IPv4 address will resul… |
| 1.3.6.1.4.1.4115.1.3.1.1.4.2 | ScalararrisCmDevSwAdminStatus | read-write | current | If set to upgradeFromArrisMgt(1), the device will initiate a TFTP software image download using arrisCmDevSwFilename for the matching HW model type and revisio… |
| 1.3.6.1.4.1.4115.1.3.1.10 | NodearrisCmDevNotification | |||
| 1.3.6.1.4.1.4115.1.3.1.10.0 | NodearrisCmDevTraps | |||
| 1.3.6.1.4.1.4115.1.3.1.10.0.2 | NotificationarrisCmDevTftpDownloadInitTrap | current | An event that indicates a TFTP download initiated request. The values of docsDevEvLevel, docsDevId, and docsDevEvText are from the entry which logs this event … | |
| 1.3.6.1.4.1.4115.1.3.1.10.0.3 | NotificationarrisCmDevTftpDownloadCompleteTrap | current | An event that indicates the TFTP download completed successfully. | |
| 1.3.6.1.4.1.4115.1.3.1.10.0.4 | NotificationarrisCmDevTftpDownloadFailTrap | current | An event that indicates the failure of the TFTP download attempt. | |
| 1.3.6.1.4.1.4115.1.3.1.10.0.5 | NotificationarrisCmDevTftpDownloadRetryTrap | current | An event that indicates a TFTP download retry attempt. | |
| 1.3.6.1.4.1.4115.1.3.1.10.0.6 | NotificationarrisCmDevMtaCertificateValidationFailTrap | current | An event that indicates a Service Provider Certificate Chain Validation Failed. | |
| 1.3.6.1.4.1.4115.1.3.1.10.0.8 | NotificationarrisCmDevSoftwareUpgradeFailedBeforeDLTrap | current | An event that indicates the Software Upgrade Failed before downloading. | |
| 1.3.6.1.4.1.4115.1.3.1.10.0.9 | NotificationarrisCmDevSoftwareUpgradeFailedTrap | current | An event that indicates the Software Upgrade Failed. | |
| 1.3.6.1.4.1.4115.1.3.1.10.0.10 | NotificationarrisCmDevSoftwareUpgradeCompleteTrap | current | An event that indicates the Software Upgrade was Completed. | |
| 1.3.6.1.4.1.4115.1.3.1.10.0.11 | NotificationarrisCmDevSoftwareUpgradeAbortedACFailTrap | current | An event that indicates the Software Upgrade was Aborted due to battery AC-FAIL condition. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| ArrsCmDevProvMethod | INTEGER { docsisOnly(0), fullPacketCable(1), packetCableMinusKDC(2), cps(3), gupi(4), singleMAC(5), basic1(6), basic2(7), gupiEncryptedMtaConfig(8), gupiMacMta(9), gupiEncryptedMacMta(10), gupiTftpSvrOverride(11) } | deprecated | These are the various provisioning methods that are supported by the device. |