ATS-MIB
164 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC-1212 | OBJECT-TYPE |
| RFC-1215 | TRAP-TYPE |
| RFC1155-SMI | Counter enterprises IpAddress |
| RFC1213-MIB | DisplayString |
| UPS-MIB | NonNegativeInteger PositiveInteger |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.37662 | Nodeats | |||
| 1.3.6.1.4.1.37662.1 | Nodeproduct | |||
| 1.3.6.1.4.1.37662.1.2 | NodewebAppliance | |||
| 1.3.6.1.4.1.37662.1.2.2 | NodeatsAgent | |||
| 1.3.6.1.4.1.37662.1.2.2.1 | Nodesingle | |||
| 1.3.6.1.4.1.37662.1.2.2.1.1 | NodeatsObjectGroup | |||
| 1.3.6.1.4.1.37662.1.2.2.1.1.1 | NodeatsIdentGroup | |||
| 1.3.6.1.4.1.37662.1.2.2.1.1.1.1 | ScalaratsIdentGroupModel | read-only | mandatory | The device model name. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.1.2 | ScalaratsIdentGroupSerialNumber | read-only | mandatory | The device serial number. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.1.3 | ScalaratsIdentGroupManufacturer | read-only | mandatory | The device manufacturer name. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.1.4 | ScalaratsIdentGroupFirmwareRevision | read-only | mandatory | The device firmware revision. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.1.5 | ScalaratsIdentGroupAgentFirmwareRevision | read-only | mandatory | The agent firmware revision. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.2 | NodeatsInputGroup | |||
| 1.3.6.1.4.1.37662.1.2.2.1.1.2.1 | ScalaratsInputGroupPreference | read-only | mandatory | This shows the Output Source Priority by Source A or Source B. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.2.2 | ScalaratsInputGroupSourceAstatus | read-only | mandatory | This field shows the status of the source A. Status included? 'OK','Fail'. 'OK' mean frequency and voltage of Source A are normal. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.2.3 | ScalaratsInputGroupSourceAinputVoltage | read-only | mandatory | The source A input voltage of the ATS input in volts. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.2.4 | ScalaratsInputGroupSourceAinputFrequency | read-only | mandatory | The source A input frequency of the ATS input in 0.1 Hz. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.2.5 | ScalaratsInputGroupSourceBstatus | read-only | mandatory | This field shows the status of the source B. Status included? 'OK','Fail'. 'OK' mean frequency and voltage of Source B are normal. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.2.6 | ScalaratsInputGroupSourceBinputVoltage | read-only | mandatory | The source B input voltage of the ATS input in volts. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.2.7 | ScalaratsInputGroupSourceBinputFrequency | read-only | mandatory | The source B input frequency of the ATS input in 0.1 Hz. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.2.8 | ScalaratsInputGroupSourceAvoltageUpperLimit | read-only | mandatory | The source A voltage upper limit of the ATS input in volts. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.2.9 | ScalaratsInputGroupSourceAvoltageLowerLimit | read-only | mandatory | The source A voltage lower limit of the ATS input in volts. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.2.10 | ScalaratsInputGroupSourceAfrequencyUpperLimit | read-only | mandatory | The source A frequency upper limit of the ATS input in 0.1 Hz. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.2.11 | ScalaratsInputGroupSourceAfrequencyLowerLimit | read-only | mandatory | The source A frequency lower limit of the ATS input in 0.1 Hz. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.2.12 | ScalaratsInputGroupSourceBvoltageUpperLimit | read-only | mandatory | The source B voltage upper limit of the ATS input in volts. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.2.13 | ScalaratsInputGroupSourceBvoltageLowerLimit | read-only | mandatory | The source B voltage lower limit of the ATS input in volts. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.2.14 | ScalaratsInputGroupSourceBfrequencyUpperLimit | read-only | mandatory | The source B frequency upper limit of the ATS input in 0.1 Hz. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.2.15 | ScalaratsInputGroupSourceBfrequencyLowerLimit | read-only | mandatory | The source B frequency lower limit of the ATS input in 0.1 Hz. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.3 | NodeatsOutputGroup | |||
| 1.3.6.1.4.1.37662.1.2.2.1.1.3.1 | ScalaratsOutputGroupOutputSource | read-only | mandatory | Output source is supply by Source A or Source B. Status included? 'Source A','Source B'. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.3.2 | ScalaratsOutputGroupOutputVoltage | read-only | mandatory | The Output Voltage in volts. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.3.3 | ScalaratsOutputGroupOutputFequency | read-only | mandatory | The output fequency in 0.1 Hz. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.3.4 | ScalaratsOutputGroupOutputCurrent | read-only | mandatory | The output current in 0.1 A. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.3.5 | ScalaratsOutputGroupLoad | read-only | mandatory | The load in %. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.4 | NodeatsHmiSwitchGroup | |||
| 1.3.6.1.4.1.37662.1.2.2.1.1.4.1 | ScalaratsHmiSwitchGroupBuzzer | read-only | mandatory | This field shows the status of the buzzer. Status included? 'Enable','Disable'. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.4.2 | ScalaratsHmiSwitchGroupAtsAlarm | read-only | mandatory | This shows the alarm occured. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.4.3 | ScalaratsHmiSwitchGroupAutoReturn | read-only | mandatory | Auto recover to that setting value when two input source normal. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.4.4 | ScalaratsHmiSwitchGroupSourceTransferByLoad | read-only | mandatory | On: If overload timeout occurred , ATS will tranfer to another source automaticlly. Off:If overload timeout occurred , ATS will turn off the output source. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.4.5 | ScalaratsHmiSwitchGroupSourceTransferByPhase | read-only | mandatory | On: when the transfer of output source occur, the transfer can active if differernce of phase less than setting value Off: Switch transfer immed... whatever di… |
| 1.3.6.1.4.1.37662.1.2.2.1.1.5 | NodeatsMiscellaneousGroup | |||
| 1.3.6.1.4.1.37662.1.2.2.1.1.5.1 | ScalaratsMiscellaneousGroupAtsSystemTemperture | read-only | mandatory | The ATS system temperture in degree C. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.5.2 | ScalaratsMiscellaneousGroupSystemMaxCurrent | read-only | mandatory | The system max current int 0.1 Amp. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.6 | NodeatsControlGroup | |||
| 1.3.6.1.4.1.37662.1.2.2.1.1.6.1 | ScalaratsControlGroupBuzzerAlarmControl | read-write | mandatory | The buzzer alarm control. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.6.2 | ScalaratsControlGroupManualTransfer | read-write | mandatory | User can click this bottom to decide output source supply is Source A or Source B. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.7 | NodeagentConfig | |||
| 1.3.6.1.4.1.37662.1.2.2.1.1.7.1 | ScalaragentConfigIpaddress | read-write | mandatory | The ip address that NMS can identify the managed device |
| 1.3.6.1.4.1.37662.1.2.2.1.1.7.2 | ScalaragentConfigGateway | read-write | mandatory | The default gateway that allow device managed through routers |
| 1.3.6.1.4.1.37662.1.2.2.1.1.7.3 | ScalaragentConfigSubnetMask | read-write | mandatory | Internet address subnet mask |
| 1.3.6.1.4.1.37662.1.2.2.1.1.7.4 | ScalaragentConfigDate | read-write | mandatory | The date in agent, format is (dd/mm/yyyy) |
| 1.3.6.1.4.1.37662.1.2.2.1.1.7.5 | ScalaragentConfigTime | read-write | mandatory | The time in agent, format is (hh:mm:ss) |
| 1.3.6.1.4.1.37662.1.2.2.1.1.7.6 | ScalaragentConfigHistoryLogFrequency | read-write | mandatory | The frequency of the updation of the history log. The value is in seconds |
| 1.3.6.1.4.1.37662.1.2.2.1.1.7.7 | ScalaragentConfigExtHistoryLogFrequency | read-write | mandatory | The ups parameters are sampled at the rate governed by the mconfigHistroyLogFrequency. These sampled values are further conslidated over period of time which i… |
| 1.3.6.1.4.1.37662.1.2.2.1.1.7.8 | ScalaragentConfigPollRate | read-write | mandatory | The frequency that proxy agent polls the connected UPS in JBUS protocol. (unit : second) |
| 1.3.6.1.4.1.37662.1.2.2.1.1.7.9 | ScalaragentConfigBaudRate | read-only | mandatory | The serial port communication speed. only 9600 allowed |
| 1.3.6.1.4.1.37662.1.2.2.1.1.7.10 | ScalaragentConfigDhcpStatue | read-write | mandatory | Enable or disable DHCP/BootP capability |
| 1.3.6.1.4.1.37662.1.2.2.1.1.7.11 | ScalaragentConfigTelnetStatue | read-write | mandatory | Enable or disable telnet access |
| 1.3.6.1.4.1.37662.1.2.2.1.1.7.12 | ScalaragentConfigTftpStatue | read-write | mandatory | Enable or disable network upgrade capability |
| 1.3.6.1.4.1.37662.1.2.2.1.1.7.13 | ScalaragentConfigResetToDefault | read-write | mandatory | Reset all parameters of ATS to default value |
| 1.3.6.1.4.1.37662.1.2.2.1.1.7.14 | ScalaragentConfigRestart | read-write | mandatory | Restart ATS |
| 1.3.6.1.4.1.37662.1.2.2.1.1.7.15 | ScalaragentConfigClearAgentLog | read-write | mandatory | Clear agent log data |
| 1.3.6.1.4.1.37662.1.2.2.1.1.7.16 | ScalaragentConfigClearEventLog | read-write | mandatory | Clear event log data |
| 1.3.6.1.4.1.37662.1.2.2.1.1.7.17 | ScalaragentConfigClearExtHistoryLog | read-write | mandatory | Clear extented history log data |
| 1.3.6.1.4.1.37662.1.2.2.1.1.7.18 | ScalaragentConfigClearHistoryLog | read-write | mandatory | Clear history log data |
| 1.3.6.1.4.1.37662.1.2.2.1.1.7.19 | ScalaragentConfigTrapRetryCount | read-write | mandatory | The count of repeat traps to send to NMS before trap acknowledge received. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.7.20 | ScalaragentConfigTrapRetryTime | read-write | mandatory | The time between retry traps sned to NMS. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.7.21 | ScalaragentConfigTrapAckSignature | read-write | mandatory | The signature of trap acknowledge. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.7.22 | ScalaragentConfigMibVersion | read-only | mandatory | The version of MIB spec. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.7.23 | TableagentConfigTrapsReceiversTable | not-accessible | mandatory | A list of managers to send traps to. The number of entries is given by the value of agentConfigNumTrapReceivers |
| 1.3.6.1.4.1.37662.1.2.2.1.1.7.23.1 | RowagentConfigTrapsReceiversEntry | not-accessible | mandatory | The managers to send traps to. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.7.23.1.1 | ColumntrapsIndex | read-only | mandatory | The index to a trap receiver entry. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.7.23.1.2 | ColumntrapsReceiverAddr | read-write | mandatory | The IP address of the manager to send a trap to. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.7.23.1.3 | ColumnreceiverCommunityString | read-write | mandatory | The community name to use in the trap when sent to the manager. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.7.23.1.4 | ColumnreceiverNmsType | read-write | mandatory | The trap group that NMS desired. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.7.23.1.5 | ColumnreceiverSeverityLevel | read-write | mandatory | The severity level of traps to be received by this manager. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.7.23.1.6 | ColumnreceiverDescription | read-write | mandatory | Description of trap receivers |
| 1.3.6.1.4.1.37662.1.2.2.1.1.7.24 | TableagentConfigAccessControlTable | not-accessible | mandatory | A list of managers which can access ATS with private community string. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.7.24.1 | RowagentConfigAccessControlEntry | not-accessible | mandatory | The managers. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.7.24.1.1 | ColumnaccessIndex | read-only | mandatory | The index to a access control entry. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.7.24.1.2 | ColumnaccessControlAddr | read-write | mandatory | The IP address of the manager to access ATS |
| 1.3.6.1.4.1.37662.1.2.2.1.1.7.24.1.3 | ColumnaccessCommunityString | read-write | mandatory | The community name to use in the manager when access ATS |
| 1.3.6.1.4.1.37662.1.2.2.1.1.7.24.1.4 | ColumnaccessControlMode | read-write | mandatory | Access type, only read/Write access type can change parameter of ATS |
| 1.3.6.1.4.1.37662.1.2.2.1.1.7.25 | ScalaragentConfigDefaultLanguage | read-write | mandatory | The default languauge for browser, when set to auto(1) ATS will send page in the language depends on the request language of browser. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.7.26 | ScalaragentConfigIPv6AddrStatus | read-only | mandatory | The status of IPv6 global address. When the auto-configuration of IPv6 address is disabled, it shows manual configuration(3). Otherwise, it shows valid(2) for … |
| 1.3.6.1.4.1.37662.1.2.2.1.1.7.27 | ScalaragentConfigIPv6AddrAutoConfig | read-write | mandatory | The state of IPv6 address auto-configuration. If set to enable(1), ATS will try to get a valid global/site-local address from IPv6 router or DHCPv6 server on t… |
| 1.3.6.1.4.1.37662.1.2.2.1.1.7.28 | ScalaragentConfigIPv6LinkLocalAddr | read-only | mandatory | The IPv6 link-local address of ATS. It is auto-configured based on MAC address of ATS. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.7.29 | ScalaragentConfigIPv6GlobalAddr | read-write | mandatory | The IPv6 global/site-local address of ATS. If change it manually, the agentConfigIPv6AddrStatus and agentConfigIPv6AddrAutoConfig will be changed to manual con… |
| 1.3.6.1.4.1.37662.1.2.2.1.1.7.30 | ScalaragentConfigIPv6PrefixlLength | read-write | mandatory | The prefix length of IPv6 global/site-local address.If change it manually, the agentConfigIPv6AddrStatus and agentConfigIPv6AddrAutoConfig will be changed to m… |
| 1.3.6.1.4.1.37662.1.2.2.1.1.7.31 | ScalaragentConfigIPv6DefaultRouter | read-write | mandatory | The address of IPv6 default router. If change it manually, the agentConfigIPv6AddrStatus and agentConfigIPv6AddrAutoConfig will be changed to manual configurat… |
| 1.3.6.1.4.1.37662.1.2.2.1.1.8 | NodeemdStatus | |||
| 1.3.6.1.4.1.37662.1.2.2.1.1.8.1 | ScalaremdSatatusEmdType | read-only | mandatory | The type of EMD plugged into the port. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.8.2 | ScalaremdSatatusTemperature | read-only | mandatory | The measurement of EMD temperature, in 0.1 degree |
| 1.3.6.1.4.1.37662.1.2.2.1.1.8.3 | ScalaremdSatatusHumidity | read-only | mandatory | The measurement of EMD humidity, in 0.1 degree |
| 1.3.6.1.4.1.37662.1.2.2.1.1.8.4 | ScalaremdSatatusAlarm1 | read-only | mandatory | The EMD alarm-1 status |
| 1.3.6.1.4.1.37662.1.2.2.1.1.8.5 | ScalaremdSatatusAlarm2 | read-only | mandatory | The EMD alarm-2 status |
| 1.3.6.1.4.1.37662.1.2.2.1.1.9 | NodeemdConfig | |||
| 1.3.6.1.4.1.37662.1.2.2.1.1.9.1 | ScalarusahEmdConfigEmdConfig | read-write | mandatory | Enable or disable to detect presence of EMD |
| 1.3.6.1.4.1.37662.1.2.2.1.1.9.2 | ScalaremdConfigEmdName | read-write | mandatory | Description of EMD |
| 1.3.6.1.4.1.37662.1.2.2.1.1.9.3 | NodeemdConfigTemperature | |||
| 1.3.6.1.4.1.37662.1.2.2.1.1.9.3.1 | ScalaremdConfigTempName | read-write | mandatory | Description of EMD temperature sensor |
| 1.3.6.1.4.1.37662.1.2.2.1.1.9.3.2 | ScalaremdConfigTempHighSetPoint | read-write | mandatory | The set point for high temperature warning, in degrees |
| 1.3.6.1.4.1.37662.1.2.2.1.1.9.3.3 | ScalaremdConfigTempHighStatus | read-write | mandatory | To enable/disable high set point check with emd temperature. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.9.3.4 | ScalaremdConfigTempLowSetPoint | read-write | mandatory | The set point for low temperature warning, in degrees |
| 1.3.6.1.4.1.37662.1.2.2.1.1.9.3.5 | ScalaremdConfigTempLowStatus | read-write | mandatory | To enable/disable low set point check with emd temperature. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.9.3.6 | ScalaremdConfigTempOffset | read-write | mandatory | The offset to calibrate temperature of EMD, in degrees |
| 1.3.6.1.4.1.37662.1.2.2.1.1.9.4 | NodeemdConfigHumidity | |||
| 1.3.6.1.4.1.37662.1.2.2.1.1.9.4.1 | ScalaremdConfigHumidityName | read-write | mandatory | Description of EMD humidity sensor |
| 1.3.6.1.4.1.37662.1.2.2.1.1.9.4.2 | ScalaremdConfigHumidityHighSetPoint | read-write | mandatory | The set point for high humidity warning, in % |
| 1.3.6.1.4.1.37662.1.2.2.1.1.9.4.3 | ScalaremdConfigHumidityHighStatus | read-write | mandatory | To enable/disable high set point check with emd humidity. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.9.4.4 | ScalaremdConfigHumidityLowSetPoint | read-write | mandatory | The set point for low humidity warning, in % |
| 1.3.6.1.4.1.37662.1.2.2.1.1.9.4.5 | ScalaremdConfigHumidityLowStatus | read-write | mandatory | To enable/disable low set point check with emd humidity. |
| 1.3.6.1.4.1.37662.1.2.2.1.1.9.4.6 | ScalaremdConfigHumidityOffset | read-write | mandatory | The offset to calibrate humidity of EMD, in % |
| 1.3.6.1.4.1.37662.1.2.2.1.1.9.5 | NodeemdConfigAlarm1 | |||
| 1.3.6.1.4.1.37662.1.2.2.1.1.9.5.1 | ScalaremdConfigAlarm1Name | read-write | mandatory | Description of EMD alarm-1 |
| 1.3.6.1.4.1.37662.1.2.2.1.1.9.5.2 | ScalaremdConfigAlarm1Type | read-write | mandatory | The alarm-1 operation type |
| 1.3.6.1.4.1.37662.1.2.2.1.1.9.6 | NodeemdConfigAlarm2 | |||
| 1.3.6.1.4.1.37662.1.2.2.1.1.9.6.1 | ScalaremdConfigAlarm2Name | read-write | mandatory | Description of EMD alarm-2 |
| 1.3.6.1.4.1.37662.1.2.2.1.1.9.6.2 | ScalaremdConfigAlarm2Type | read-write | mandatory | The alarm-1 operation type |
| 1.3.6.1.4.1.37662.1.2.2.1.2 | NodeatsTrapGroup | |||
| 1.3.6.1.4.1.37662.1.2.2.1.2.1 | NodeatsAtsAlarm | WARNING: ATS Alarm. | ||
| 1.3.6.1.4.1.37662.1.2.2.1.2.2 | NodeatsSourceAvoltageAbnormal | WARNING: Source A voltage abnormal. | ||
| 1.3.6.1.4.1.37662.1.2.2.1.2.3 | NodeatsSourceBvoltageAbnormal | WARNING: Source B voltage abnormal. | ||
| 1.3.6.1.4.1.37662.1.2.2.1.2.4 | NodeatsSourceAfrequencyAbnormal | WARNING: Source A frequency abnormal. | ||
| 1.3.6.1.4.1.37662.1.2.2.1.2.5 | NodeatsSourceBfrequencyAbnormal | WARNING: Source B frequency abnormal. | ||
| 1.3.6.1.4.1.37662.1.2.2.1.2.6 | NodeatsOutputOverLoad | SEVERE: Output over load. | ||
| 1.3.6.1.4.1.37662.1.2.2.1.2.7 | NodeatsWorkPowerAabnormal | SEVERE: Unit fault (Working power A abnormal). | ||
| 1.3.6.1.4.1.37662.1.2.2.1.2.8 | NodeatsWorkPowerBabnormal | SEVERE: Unit fault (Working power B abnormal). | ||
| 1.3.6.1.4.1.37662.1.2.2.1.2.9 | NodeatsOverTemperature | WARNING: Cabinet over temperature. | ||
| 1.3.6.1.4.1.37662.1.2.2.1.2.10 | NodeatsDcOffsetAbnormal | SEVERE: Unit fault (Sensor circuit abnormal). | ||
| 1.3.6.1.4.1.37662.1.2.2.1.2.11 | NodeatsEepromAbnormal | SEVERE: Unit fault (EEPROM data abnormal) | ||
| 1.3.6.1.4.1.37662.1.2.2.1.2.12 | NodeatsLcdNotConnect | SEVERE: LCD panel connection abnormal. | ||
| 1.3.6.1.4.1.37662.1.2.2.1.2.13 | NodeatsOutputExceedsOverloadTime | SEVERE: Overload time out, Output off, Reset needed. | ||
| 1.3.6.1.4.1.37662.1.2.2.1.2.14 | NodeatsInputPhaseDifference | SEVERE: Phase difference between resources exceed user defined value, Output off, Reset needed. | ||
| 1.3.6.1.4.1.37662.1.2.2.1.2.15 | NodeatsUserSetOverLoad | WARNING: User defined load pre-alarm. | ||
| 1.3.6.1.4.1.37662.1.2.2.1.2.16 | NodeatsAtsAlarmToNormal | INFORMATION: ATS Alarm Normal. | ||
| 1.3.6.1.4.1.37662.1.2.2.1.2.17 | NodeatsSourceAvoltageAbnormalToNormal | INFORMATION: Source A Voltage Normal. | ||
| 1.3.6.1.4.1.37662.1.2.2.1.2.18 | NodeatsSourceBvoltageAbnormalToNormal | INFORMATION: Source B Voltage Normal. | ||
| 1.3.6.1.4.1.37662.1.2.2.1.2.19 | NodeatsSourceAfrequencyAbnormalToNormal | INFORMATION: Source A Frequency Normal. | ||
| 1.3.6.1.4.1.37662.1.2.2.1.2.20 | NodeatsSourceBfrequencyAbnormalToNormal | INFORMATION: Source B Frequency Normal. | ||
| 1.3.6.1.4.1.37662.1.2.2.1.2.21 | NodeatsOutputOverLoadToNormal | INFORMATION: Output Load Normal. | ||
| 1.3.6.1.4.1.37662.1.2.2.1.2.22 | NodeatsWorkPowerAabnormalToNormal | INFORMATION: Unit Normal (Working power A normal). | ||
| 1.3.6.1.4.1.37662.1.2.2.1.2.23 | NodeatsWorkPowerBabnormalToNormal | INFORMATION: Unit Normal (Working power B normal). | ||
| 1.3.6.1.4.1.37662.1.2.2.1.2.24 | NodeatsOverTemperatureToNormal | INFORMATION: Cabinet temperature Normal. | ||
| 1.3.6.1.4.1.37662.1.2.2.1.2.25 | NodeatsDcOffsetAbnormalToNormal | INFORMATION: Unit Normal (Sensor circuit normal). | ||
| 1.3.6.1.4.1.37662.1.2.2.1.2.26 | NodeatsEepromAbnormalToNormal | INFORMATION: Unit normal (EEPROM data normal) | ||
| 1.3.6.1.4.1.37662.1.2.2.1.2.27 | NodeatsLcdNotConnectToNormal | INFORMATION: LCD panel connection normal. | ||
| 1.3.6.1.4.1.37662.1.2.2.1.2.28 | NodeatsOutputExceedsOverloadTimeToNormal | INFORMATION: Output Load Normal. | ||
| 1.3.6.1.4.1.37662.1.2.2.1.2.29 | NodeatsInputPhaseDifferenceToNormal | INFORMATION: Input sources return to normal phase. | ||
| 1.3.6.1.4.1.37662.1.2.2.1.2.30 | NodeatsUserSetOverLoadToNormal | INFORMATION: User defined load return to Normal. | ||
| 1.3.6.1.4.1.37662.1.2.2.1.2.31 | NodeatsCommunicationLost | SEVERE: Communication to the ATS has been lost. Steps to reestablish communication are in progress. | ||
| 1.3.6.1.4.1.37662.1.2.2.1.2.32 | NodeatsCommunicationEstablished | INFORMATION: Communication with the ATS has been established. | ||
| 1.3.6.1.4.1.37662.1.2.2.1.2.33 | NodeemdTemperatureNotHigh | INFORMATION: The temperature of EMD back to normal from high warning. | ||
| 1.3.6.1.4.1.37662.1.2.2.1.2.34 | NodeemdTemperatureTooHigh | WARNING: The temperature of EMD higher than set point. | ||
| 1.3.6.1.4.1.37662.1.2.2.1.2.35 | NodeemdTemperatureNotLow | INFORMATION: The temperature of EMD back to normal from low warning. | ||
| 1.3.6.1.4.1.37662.1.2.2.1.2.36 | NodeemdTemperatureTooLow | WARNING: The temperature of EMD lower than set point. | ||
| 1.3.6.1.4.1.37662.1.2.2.1.2.37 | NodeemdHumidityNotHigh | INFORMATION: The humidity of EMD back to normal from high warning. | ||
| 1.3.6.1.4.1.37662.1.2.2.1.2.38 | NodeemdHumidityTooHigh | WARNING: The humidity of EMD higher than set point. | ||
| 1.3.6.1.4.1.37662.1.2.2.1.2.39 | NodeemdHumidityNotLow | INFORMATION: The humidity of EMD back to normal from low warning. | ||
| 1.3.6.1.4.1.37662.1.2.2.1.2.40 | NodeemdHumidityTooLow | WARNING: The humidity of EMD lower than set point. | ||
| 1.3.6.1.4.1.37662.1.2.2.1.2.41 | NodeemdAlarm1Normal | INFORMATION: The status of emd alarm-1 back to normal from active. | ||
| 1.3.6.1.4.1.37662.1.2.2.1.2.42 | NodeemdAlarm1Active | WARNING: The status of emd alarm-1 activated. | ||
| 1.3.6.1.4.1.37662.1.2.2.1.2.43 | NodeemdAlarm2Normal | INFORMATION: The status of emd alarm-2 back to normal from active. | ||
| 1.3.6.1.4.1.37662.1.2.2.1.2.44 | NodeemdAlarm2Active | WARNING: The status of emd alarm-2 activated. |