C-PRODUCT-QSIM-MIB
68 objects
No module-level DESCRIPTION found.
Imported Objects
| C-PRODUCT-BASE-MIB | cardSlot portNumber portSlot vcpSideId |
| C-PRODUCT-GROUP-MIB | qsim |
| RFC-1212 | OBJECT-TYPE |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.1 | NodeqsimCard | |||
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.1.1 | TableqsimCardTable | not-accessible | mandatory | Card configuration table. |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.1.1.1 | RowqsimCardEntry | not-accessible | mandatory | Card configuration entry. |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.1.1.1.1 | ColumnqsimCardMaxFrameSize | read-write | mandatory | Maximum frame size for SDLC, DXI and Frame Relay frames. WARNING: Change of the Maximum Frame Size will cause Disruption of Service provided by the card. |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.2 | NodeqsimPort | |||
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.2.1 | TableqsimPortTable | not-accessible | mandatory | QSIM port configuration table. |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.2.1.1 | RowqsimPortEntry | not-accessible | mandatory | QSIM port configuration entry. The slot number (portSlot) of this card can be from 4 to 6. The port number (portNumber) can be from 1 to 4. |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.2.1.1.1 | ColumnqsimPortLinkType | read-write | mandatory | Link layer protocol supported by the port. |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.2.1.1.2 | ColumnqsimPortCableType | read-only | mandatory | Type of cable connected to the port. |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.2.1.1.3 | ColumnqsimPortTermTimingSource | read-write | mandatory | Terminal timing source. This object applies ONLY when a DCE cable is connected to the port. If cable type is 'none' or 'dce', this object can be read and writt… |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.2.1.1.4 | ColumnqsimPortReceiveTimingPhase | read-write | mandatory | Receive timing phase control. This object applies ONLY when a DCE cable is connected to the port. If cable type is 'none' or 'dce', this object can be read and… |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.2.1.1.5 | ColumnqsimPortDataRate | read-write | mandatory | Data rate supported by the port. |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.2.1.1.6 | ColumnqsimPortMinFlagBytes | read-write | mandatory | Minimum flag bytes required to distinguish a frame. |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.2.1.1.7 | ColumnqsimPortFcsSize | read-write | mandatory | Number of bytes in the FCS field of a frame. |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.2.1.1.8 | ColumnqsimPortRts | read-only | mandatory | RTS pin status. |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.2.1.1.9 | ColumnqsimPortCts | read-only | mandatory | CTS pin status. |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.2.1.1.10 | ColumnqsimPortDcd | read-only | mandatory | DCD pin status. |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.2.1.1.11 | ColumnqsimPortDsr | read-only | mandatory | DSR pin status. |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.3 | NodehsimPort | |||
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.3.1 | TablehsimPortTable | not-accessible | mandatory | HSIM port configuration table. |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.3.1.1 | RowhsimPortEntry | not-accessible | mandatory | HSIM port configuration entry. The slot number (portSlot) of this card can be from 4 to 6. The port number (portNumber) of this card is always 1. |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.3.1.1.1 | ColumnhsimPortLinkType | read-write | mandatory | Link layer protocol supported by the port. |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.3.1.1.2 | ColumnhsimPortDceDteMode | read-write | mandatory | DCE/DTE mode of the port. |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.3.1.1.3 | ColumnhsimPortDataRate | read-only | mandatory | Data rate supported by the port. |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.3.1.1.4 | ColumnhsimPortMinFlagBytes | read-write | mandatory | Minimum flag bytes required to distinguish a frame. |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.3.1.1.5 | ColumnhsimPortFcsSize | read-write | mandatory | Number of bytes in the FCS field of a frame. |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.3.1.1.6 | ColumnhsimPortTa | read-only | mandatory | TA pin status. |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.3.1.1.7 | ColumnhsimPortCa | read-only | mandatory | CA pin status. |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.4 | NodeqsimVc | |||
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.4.1 | NodeqsimSdlcVc | |||
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.4.2 | NodeqsimDxiVc | |||
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.4.3 | NodeqsimFrameRelayVc | |||
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.6 | NodeqsimLmi | |||
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.6.1 | TableqsimLmiTable | not-accessible | mandatory | LMI configuration table. |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.6.1.1 | RowqsimLmiEntry | not-accessible | mandatory | LMI configuration entry. The slot number (portSlot) should be from 4 to 6. The port number (portNumber) is from 1 to 4 for QSIM card, 1 to 8 for FAM card, and … |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.6.1.1.1 | ColumnqsimLmiProtocol | read-write | mandatory | LMI protocol supported by the port. |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.6.1.1.2 | ColumnqsimLmiProcedure | read-write | mandatory | LMI procedure supported by the port. This object applies when LMI Q.933 Annex A or T1.617 Annex D protocol is selected. |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.6.1.1.3 | ColumnqsimLmiUserT391 | read-write | mandatory | User-side link integrity verification (LIV) polling timer. This object applies when LMI user-side or bidirectional procedure is selected. |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.6.1.1.4 | ColumnqsimLmiUserN391 | read-write | mandatory | User-side full status polling counter. This object applies when LMI user-side or bidirectional procedure is selected. |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.6.1.1.5 | ColumnqsimLmiUserN392 | read-write | mandatory | User-side error threshold. This object applies when LMI user-side or bidirectional procedure is selected. User-side N392 should be less than or equal to user- … |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.6.1.1.6 | ColumnqsimLmiUserN393 | read-write | mandatory | User-side monitored events count. This object applies when LMI user-side or bidirectional procedure is selected. |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.6.1.1.7 | ColumnqsimLmiNetworkT392 | read-write | mandatory | Network-side polling verification timer. This object applies when LMI network-side or bidirectional procedure is selected. |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.6.1.1.8 | ColumnqsimLmiNetworkN392 | read-write | mandatory | Network-side error threshold. This object applies when LMI network-side or bidirectional procedure is selected. Network-side N392 should be less than or equal … |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.6.1.1.9 | ColumnqsimLmiNetworkN393 | read-write | mandatory | Network-side monitored events count. This object applies when LMI network-side or bidirectional procedure is selected. |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.9 | NodeqsimNewVc | |||
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.9.1 | NodeqsimNewSdlcVc | |||
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.9.1.1 | TableqsimNewSdlcVcTable | not-accessible | mandatory | SDLC VC configuration table. |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.9.1.1.1 | RowqsimNewSdlcVcEntry | not-accessible | mandatory | SDLC VC configuration entry. The slot number (vcPortSlot) of the VC can be from 4 to maxslots. The port number (vcPortPort) can be from 1 to 4. |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.9.1.1.1.1 | ColumnqsimNewSdlcVcShapper | read-write | mandatory | Data rate supported by the SDLC VC. Depending on the type of card a VC is configured, the shapper numbers are assigned as follows: HSIM QSIM data rate data rat… |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.9.2 | NodeqsimNewDxiVc | |||
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.9.2.1 | TableqsimNewDxiVcTable | not-accessible | mandatory | DXI VC configuration table. |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.9.2.1.1 | RowqsimNewDxiVcEntry | not-accessible | mandatory | DXI VC configuration entry. The slot number (vcPortSlot) of the VC can be from 4 to 6. The port number (vcPortPort) can be from 1 to 4. |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.9.2.1.1.1 | ColumnqsimNewDxiVcDfaVpi | read-write | mandatory | DXI DFA VPI. |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.9.2.1.1.2 | ColumnqsimNewDxiVcDfaVci | read-write | mandatory | DXI DFA VCI. |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.9.2.1.1.3 | ColumnqsimNewDxiVcDfaVciRange | read-write | mandatory | DXI VCI range. This object is used to create a set of VCs whose VPI equals to the value of the instance of qsimDxiVcDfaVpi and whose VCIs are in the range FROM… |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.9.2.1.1.4 | ColumnqsimNewDxiVcShapper | read-write | mandatory | Data rate supported by the DXI VC. Depending on the type of card a VC is configured, the shapper numbers are assigned as follows: HSIM QSIM data rate data rate… |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.9.3 | NodeqsimNewFrameRelayVc | |||
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.9.3.1 | TableqsimNewFrameRelayVcTable | not-accessible | mandatory | Frame relay VC configuration table. |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.9.3.1.1 | RowqsimNewFrameRelayVcEntry | not-accessible | mandatory | Frame relay VC configuration entry. The slot number (vcPortSlot) of the VC can be from 4 to maxslots. The port number (vcPortPort) can be from 1 to 4. |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.9.3.1.1.1 | ColumnqsimNewFrameRelayVcInterworking | read-write | mandatory | Frame Relay/ATM interworking mode. |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.9.3.1.1.2 | ColumnqsimNewFrameRelayVcEncapsulation | read-write | mandatory | Encapsulation type. This object applies ONLY to service interworking. |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.9.3.1.1.3 | ColumnqsimNewFrameRelayVcDe2Clp | read-write | mandatory | If mode 1 mapping is desirable, the user shall select direct mapping. If mode 2 mapping is desirable, the user shall select always-0 or always-1 to map the CLP… |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.9.3.1.1.4 | ColumnqsimNewFrameRelayVcClp2De | read-write | mandatory | For network interworking - The options are none and direct. If mode 1 mapping is desirable, the user shall select direct mapping. If mode 2 mapping is desirabl… |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.9.3.1.1.5 | ColumnqsimNewFrameRelayVcFecnToEfci | read-write | mandatory | This object applies ONLY to service interworking. If mode 1 mapping is desirable, direct mapping should be selected. If mode 2 mapping is desirable, always-0 s… |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.9.3.1.1.6 | ColumnqsimNewFrameRelayVcShapper | read-write | mandatory | Data rate supported by the frame relay VC. Depending on the type of card a VC is configured, the shapper numbers are assigned as follows: HSIM QSIM data rate d… |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.9.3.1.1.7 | ColumnqsimNewFrameRelayVcDlci | read-write | mandatory | Frame relay DLCI. |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.9.3.1.1.8 | ColumnqsimNewFrameRelayVcFrSscsDlci | read-write | mandatory | This object applies ONLY to network interworking. Its valid value is 16..991 and 1022. |
| 1.3.6.1.4.1.2011.2.1.1.1.1.12.9.3.1.1.9 | ColumnqsimNewFrameRelayVcStatus | read-only | mandatory | Frame relay PVC operational status. |