CIE1000-LLDP-MIB
197 objects
This is a private version of the LLDP MIB
Imported Objects
| CIE1000-TC | CIE1000DisplayString CIE1000Integer64 CIE1000InterfaceIndex CIE1000RowEditorState CIE1000Unsigned16 CIE1000Unsigned64 CIE1000Unsigned8 |
| CISCO-IE1000-MIB | cie1000SwitchMgmt |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | TEXTUAL-CONVENTION TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.9.832.1.34 | Identitycie1000LldpMib | This is a private version of the LLDP MIB | ||
| 1.3.6.1.4.1.9.9.832.1.34.1 | Nodecie1000LldpMibObjects | |||
| 1.3.6.1.4.1.9.9.832.1.34.1.2 | Nodecie1000LldpConfig | |||
| 1.3.6.1.4.1.9.9.832.1.34.1.2.1 | Nodecie1000LldpConfigGlobal | |||
| 1.3.6.1.4.1.9.9.832.1.34.1.2.1.1 | Scalarcie1000LldpConfigGlobalReInitDelay | read-write | current | Set the LLDP tx reinitialization delay in seconds. Valid range 1-10. When a port is disabled, LLDP is disabled or the switch is rebooted, a LLDP shutdown frame… |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.1.2 | Scalarcie1000LldpConfigGlobalMsgTxHold | read-write | current | Set the LLDP tx hold times . Valid range 2-10. Each LLDP frame contains information about how long time the information in the LLDP frame shall be considered v… |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.1.3 | Scalarcie1000LldpConfigGlobalMsgTxInterval | read-write | current | Set the LLDP tx interval in seconds. The switch periodically transmits LLDP frames to its neighbors for having the network discovery information up-to-date. Th… |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.1.4 | Scalarcie1000LldpConfigGlobalTxDelay | read-write | current | Set the LLDP tx delay in seconds. Valid range 1-8192. If some configuration is changed (e.g. the IP address) a new LLDP frame is transmitted, but the time betw… |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.2 | Tablecie1000LldpConfigTable | not-accessible | current | This is a table to configure LLDP configurations for a specific interface. |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.2.1 | Rowcie1000LldpConfigEntry | not-accessible | current | Each interface has a set of control parameters |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.2.1.1 | Columncie1000LldpConfigIfIndex | accessible-for-notify | current | Logical interface number index. |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.2.1.3 | Columncie1000LldpConfigAdminState | read-write | current | Sets the LLDP admin state for the interface. |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.2.1.4 | Columncie1000LldpConfigCdpAware | read-write | current | Enables/disables CDP awareness for the interface. CDP is Cisco's equivalent to LLDP. The CDP operation is restricted to decoding incoming CDP frames (The switc… |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.2.1.5 | Columncie1000LldpConfigOptionalTlvs | read-write | current | Enables/Disables the LLDP optional TLVs. Bit mask, where setting the bit to 1 means enable transmission of the corresponding TLV. Bit 0 represents Port Descrip… |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.2.1.6 | Columncie1000LldpConfigSnmpNotificationEna | read-write | current | Enable/disable of SNMP Trap notification. |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.3 | Nodecie1000LldpConfigMed | |||
| 1.3.6.1.4.1.9.9.832.1.34.1.2.3.1 | Tablecie1000LldpConfigMedTable | not-accessible | current | This is a table to configure LLDP MEDIA configurations for a specific interface. |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.3.1.1 | Rowcie1000LldpConfigMedEntry | not-accessible | current | Each interface has a set of control parameters |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.3.1.1.1 | Columncie1000LldpConfigMedIfIndex | accessible-for-notify | current | Logical interface number index. |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.3.1.1.3 | Columncie1000LldpConfigMedOptionalTlvs | read-write | current | Enables/Disables the LLDP optional TLVs. Bit mask, where setting the bit to 1 means enable transmission of the corresponding optional TLV. Bit 0 represents the… |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.3.1.1.4 | Columncie1000LldpConfigMedDeviceType | read-write | current | Setting device type to configure the mode the device shall operate as. |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.3.2 | Tablecie1000LldpConfigMedPolicyTable | not-accessible | current | This is a table to configure LLDP MED Policies for the device. |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.3.2.1 | Rowcie1000LldpConfigMedPolicyEntry | not-accessible | current | Network Policy Discovery enables the efficient discovery and diagnosis of mismatch issues with the VLAN configuration, along with the associated Layer 2 and La… |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.3.2.1.1 | Columncie1000LldpConfigMedPolicyLldpmedPolicy | accessible-for-notify | current | Policy index. |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.3.2.1.3 | Columncie1000LldpConfigMedPolicyApplicationType | read-write | current | The LLDP policy application type. |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.3.2.1.4 | Columncie1000LldpConfigMedPolicyTagged | read-write | current | The LLDP policy tagged flag. Defines if LLDP policy uses tagged VLAN. |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.3.2.1.5 | Columncie1000LldpConfigMedPolicyVlanId | read-write | current | The LLDP policy VLAN ID. Only valid when policy 'Tagged' is TRUE |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.3.2.1.6 | Columncie1000LldpConfigMedPolicyL2Priority | read-write | current | The LLDP policy L2 priority. |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.3.2.1.7 | Columncie1000LldpConfigMedPolicyDscp | read-write | current | The LLDP policy DSCP. |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.3.2.1.100 | Columncie1000LldpConfigMedPolicyAction | read-write | current | Action |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.3.3 | Tablecie1000LldpConfigMedPolicyListTable | not-accessible | current | Each interface can be mapped to multiple policies. Set to TRUE in order to enable the corresponding policy to be transmitted at the interface. It is a requirem… |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.3.3.1 | Rowcie1000LldpConfigMedPolicyListEntry | not-accessible | current | Each location information has a control parameter |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.3.3.1.1 | Columncie1000LldpConfigMedPolicyListIfIndex | accessible-for-notify | current | Logical interface number index. |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.3.3.1.3 | Columncie1000LldpConfigMedPolicyListLldpmedPolicy | accessible-for-notify | current | Policy index. |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.3.3.1.4 | Columncie1000LldpConfigMedPolicyListLldpmedPoliciesList | read-write | current | Set to TRUE assign the corresponding policy index to the interface. |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.3.4 | Nodecie1000LldpConfigMedGlobal | |||
| 1.3.6.1.4.1.9.9.832.1.34.1.2.3.4.1 | Scalarcie1000LldpConfigMedGlobalFastRepeatCount | read-write | current | Number of times to repeat LLDP frame transmission at fast start Rapid startup and Emergency Call Service Location Identification Discovery of endpoints is a cr… |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.3.4.2 | Scalarcie1000LldpConfigMedGlobalLatitude | read-write | current | Latitude degrees in 2s-complement as specified in RFC 3825. Positive numbers are north of the equator and negative numbers are south of the equator. |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.3.4.3 | Scalarcie1000LldpConfigMedGlobalLongitude | read-write | current | Longitude degrees in 2s-complement as specified in RFC 3825. Positive values are East of the prime meridian and negative numbers are West of the prime meridian. |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.3.4.4 | Scalarcie1000LldpConfigMedGlobalAltitudeType | read-write | current | Setting altitude type Possible to select between two altitude types (floors or meters). Meters are representing meters of altitude defined by the vertical datu… |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.3.4.5 | Scalarcie1000LldpConfigMedGlobalAltitude | read-write | current | Altitude value in 2s-complement as specified in RFC 3825 |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.3.4.6 | Scalarcie1000LldpConfigMedGlobalElinAddr | read-write | current | Emergency Call Service ELIN identifier data format is defined to carry the ELIN identifier as used during emergency call setup to a traditional CAMA or ISDN tr… |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.3.4.7 | Scalarcie1000LldpConfigMedGlobalDatum | read-write | current | Setting datum to configure the datum (geodetic system) to use. The Map Datum is used for the coordinates given in these options: WGS84: (Geographical 3D) - Wor… |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.3.4.8 | Scalarcie1000LldpConfigMedGlobalCountryCode | read-write | current | The two-letter ISO 3166 country code in capital ASCII letters - Example: DK, DE or US. |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.3.5 | Tablecie1000LldpConfigMedLocationInfTable | not-accessible | current | The civic address location information. Each civic address can contain up to 250 characters, but the total amount of characters for the combined civic address … |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.3.5.1 | Rowcie1000LldpConfigMedLocationInfEntry | not-accessible | current | Each civic address type as defined in TIA1057, Section 3.4 in Annex B |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.3.5.1.2 | Columncie1000LldpConfigMedLocationInfLldpmedIndex | accessible-for-notify | current | Civic address type. 1 - State/National subdivisions 2 - County, parish, gun (JP), district (IN) 3 - City, township 4 - City division, borough, city district, w… |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.3.5.1.3 | Columncie1000LldpConfigMedLocationInfCivicAddress | read-write | current | Civic address |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.3.6 | Nodecie1000LldpConfigMedPolicyRowEditor | |||
| 1.3.6.1.4.1.9.9.832.1.34.1.2.3.6.1 | Scalarcie1000LldpConfigMedPolicyRowEditorLldpmedPolicy | read-write | current | Policy index. |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.3.6.3 | Scalarcie1000LldpConfigMedPolicyRowEditorApplicationType | read-write | current | The LLDP policy application type. |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.3.6.4 | Scalarcie1000LldpConfigMedPolicyRowEditorTagged | read-write | current | The LLDP policy tagged flag. Defines if LLDP policy uses tagged VLAN. |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.3.6.5 | Scalarcie1000LldpConfigMedPolicyRowEditorVlanId | read-write | current | The LLDP policy VLAN ID. Only valid when policy 'Tagged' is TRUE |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.3.6.6 | Scalarcie1000LldpConfigMedPolicyRowEditorL2Priority | read-write | current | The LLDP policy L2 priority. |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.3.6.7 | Scalarcie1000LldpConfigMedPolicyRowEditorDscp | read-write | current | The LLDP policy DSCP. |
| 1.3.6.1.4.1.9.9.832.1.34.1.2.3.6.100 | Scalarcie1000LldpConfigMedPolicyRowEditorAction | read-write | current | Action |
| 1.3.6.1.4.1.9.9.832.1.34.1.3 | Nodecie1000LldpStatus | |||
| 1.3.6.1.4.1.9.9.832.1.34.1.3.1 | Nodecie1000LldpStatusStatistics | |||
| 1.3.6.1.4.1.9.9.832.1.34.1.3.1.1 | Nodecie1000LldpStatusStatisticsGlobalCounters | |||
| 1.3.6.1.4.1.9.9.832.1.34.1.3.1.1.1 | Scalarcie1000LldpStatusStatisticsGlobalCountersTableInserts | read-only | current | Shows the number of new entries added since switch reboot. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.1.1.2 | Scalarcie1000LldpStatusStatisticsGlobalCountersTableDeletes | read-only | current | Shows the number of new entries deleted since switch reboot. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.1.1.3 | Scalarcie1000LldpStatusStatisticsGlobalCountersTableDrops | read-only | current | Shows the number of LLDP frames dropped due to the entry table being full. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.1.1.4 | Scalarcie1000LldpStatusStatisticsGlobalCountersTableAgeOuts | read-only | current | Shows the number of entries deleted due to Time-To-Live expiring. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.1.1.5 | Scalarcie1000LldpStatusStatisticsGlobalCountersLastChangeTime | read-only | current | Shows the time when the last entry was last deleted or added. It also shows the time elapsed since the last change was detected. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.1.2 | Tablecie1000LldpStatusStatisticsTable | not-accessible | current | This table represents the LLDP interface counters |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.1.2.1 | Rowcie1000LldpStatusStatisticsEntry | not-accessible | current | Each port interface has a set of statistics counters |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.1.2.1.1 | Columncie1000LldpStatusStatisticsIfIndex | accessible-for-notify | current | Logical interface number index. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.1.2.1.2 | Columncie1000LldpStatusStatisticsTxTotal | read-only | current | Shows the number of LLDP frames transmitted. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.1.2.1.3 | Columncie1000LldpStatusStatisticsRxTotal | read-only | current | Shows the number of LLDP frames received. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.1.2.1.4 | Columncie1000LldpStatusStatisticsRxError | read-only | current | Shows the number of received LLDP frames containing some kind of error. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.1.2.1.5 | Columncie1000LldpStatusStatisticsRxDiscarded | read-only | current | Show the number of LLDP frames discarded. If a LLDP frame is received at an interface, and the switch's internal table has run full, the LLDP frame is counted … |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.1.2.1.6 | Columncie1000LldpStatusStatisticsTLVsDiscarded | read-only | current | Shows the number of TLVs discarded. Each LLDP frame can contain multiple pieces of information, known as TLVs (TLV is short for 'Type Length Value'). If a TLV … |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.1.2.1.7 | Columncie1000LldpStatusStatisticsTLVsUnrecognized | read-only | current | Shows the number of well-formed TLVs, but with an unknown type value. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.1.2.1.8 | Columncie1000LldpStatusStatisticsTLVsOrgDiscarded | read-only | current | Shows the number of well-formed TLVs, but with an organizationally TLV which is not supported. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.1.2.1.9 | Columncie1000LldpStatusStatisticsAgeOuts | read-only | current | Show the number of age-outs. Each frame contains information about how long time the LLDP information is valid (age-out time). If no new LLDP frame is received… |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.2 | Tablecie1000LldpStatusNeighborsInfTable | not-accessible | current | This is a table to show the LLDP neighbors information for a specific interface. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.2.1 | Rowcie1000LldpStatusNeighborsInfEntry | not-accessible | current | Each interface has a set of neighbors information |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.2.1.1 | Columncie1000LldpStatusNeighborsInfIfIndex | accessible-for-notify | current | Logical interface number index. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.2.1.2 | Columncie1000LldpStatusNeighborsInfLldpmedIndex | accessible-for-notify | current | Neighbor information table entry index. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.2.1.4 | Columncie1000LldpStatusNeighborsInfChassisId | read-only | current | Shows the LLDP neighbor's chassis Id. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.2.1.5 | Columncie1000LldpStatusNeighborsInfPortId | read-only | current | Shows the LLDP neighbor's port id. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.2.1.6 | Columncie1000LldpStatusNeighborsInfPortDescription | read-only | current | Shows the LLDP neighbor's port description. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.2.1.7 | Columncie1000LldpStatusNeighborsInfSystemName | read-only | current | Shows the LLDP neighbor's system name. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.2.1.8 | Columncie1000LldpStatusNeighborsInfSystemDescription | read-only | current | Shows the LLDP neighbor's system description. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.2.1.9 | Columncie1000LldpStatusNeighborsInfSystemCapabilities | read-only | current | Shows the LLDP neighbor's system capabilities as bit mask. If the bit is set, it means that the functionality is supported by the neighbor system. Bit 0 repres… |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.2.1.10 | Columncie1000LldpStatusNeighborsInfSystemCapabilitiesEnable | read-only | current | Shows the LLDP neighbor's system capabilities which is enabled. If the bit is set, it means that the functionality is currently enabled at the neighbor system.… |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.3 | Tablecie1000LldpStatusNeighborsMgmtInfTable | not-accessible | current | This is a table to show the LLDP neighbors information for a specific interface. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.3.1 | Rowcie1000LldpStatusNeighborsMgmtInfEntry | not-accessible | current | Each interface has a set of neighbors information |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.3.1.1 | Columncie1000LldpStatusNeighborsMgmtInfIfIndex | accessible-for-notify | current | Logical interface number index. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.3.1.2 | Columncie1000LldpStatusNeighborsMgmtInfLldpmedIndex | accessible-for-notify | current | Neighbor information table entry index. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.3.1.4 | Columncie1000LldpStatusNeighborsMgmtInfLldpManagement | accessible-for-notify | current | Neighbor management information table entry index. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.3.1.5 | Columncie1000LldpStatusNeighborsMgmtInfSystemMgmAddressSubtype | read-only | current | LLDP neighbor's management address subtype , section 9.5.9.3 IEEE802.1AB-2005. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.3.1.6 | Columncie1000LldpStatusNeighborsMgmtInfSystemMgmtAddress | read-only | current | LLDP neighbor's management address string, section 9.5.9.4 IEEE802.1AB-2005. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.3.1.7 | Columncie1000LldpStatusNeighborsMgmtInfSystemMgmtInterfaceSubtype | read-only | current | Interface numbering subtype, section 9.5.9.5 IEEE802.1AB-2005. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.3.1.8 | Columncie1000LldpStatusNeighborsMgmtInfSystemMgmtInterface | read-only | current | Interface number, section 9.5.9.6 IEEE802.1AB-2005. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.3.1.9 | Columncie1000LldpStatusNeighborsMgmtInfSystemMgmtOid | read-only | current | Object identifier, section 9.5.9.8 IEEE802.1AB-2005. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4 | Nodecie1000LldpStatusMed | |||
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1 | Tablecie1000LldpStatusMedRemoteDeviceInfoTable | not-accessible | current | This is a table to show the LLDP neighbors information for a specific interface. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1 | Rowcie1000LldpStatusMedRemoteDeviceInfoEntry | not-accessible | current | Each interface has a set of neighbors information |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.1 | Columncie1000LldpStatusMedRemoteDeviceInfoIfIndex | accessible-for-notify | current | Logical interface number index. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.2 | Columncie1000LldpStatusMedRemoteDeviceInfoLldpmedIndex | accessible-for-notify | current | Neighbor information table entry index. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.4 | Columncie1000LldpStatusMedRemoteDeviceInfoCapabilities | read-only | current | LLDP neighbor's capabilities bit mask. Bit 0 represents LLDP-MED capabilities. Bit 1 represents Network Policy. Bit 2 represents Location Identification. Bit 3… |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.5 | Columncie1000LldpStatusMedRemoteDeviceInfoCapabilitiesEnabled | read-only | current | LLDP neighbor's capabilities bit mask for the capabilities which are currently enabled. Bit 0 represents LLDP-MED capabilities. Bit 1 represents Network Policy… |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.6 | Columncie1000LldpStatusMedRemoteDeviceInfoLatitude | read-only | current | Latitude degrees in 2s-complement as specified in RFC 3825. Positive numbers are north of the equator and negative numbers are south of the equator. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.7 | Columncie1000LldpStatusMedRemoteDeviceInfoLongitude | read-only | current | Longitude degrees in 2s-complement as specified in RFC 3825. Positive values are East of the prime meridian and negative numbers are West of the prime meridian. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.8 | Columncie1000LldpStatusMedRemoteDeviceInfoAltitudeType | read-only | current | Altitude type as either floors or meters. Meters are representing meters of altitude defined by the vertical datum specified. Floors are representing altitude … |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.9 | Columncie1000LldpStatusMedRemoteDeviceInfoAltitude | read-only | current | Altitude value in 2s-complement as specified in RFC 3825 |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.10 | Columncie1000LldpStatusMedRemoteDeviceInfoDatum | read-only | current | Datum (geodetic system) . The Map Datum is used for the coordinates given in these options: WGS84: (Geographical 3D) - World Geodesic System 1984, CRS Code 432… |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.11 | Columncie1000LldpStatusMedRemoteDeviceInfoElinaddr | read-only | current | Emergency Call Service ELIN identifier data format is defined to carry the ELIN identifier as used during emergency call setup to a traditional CAMA or ISDN tr… |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.12 | Columncie1000LldpStatusMedRemoteDeviceInfoDeviceType | read-only | current | Shows the LLDP neighbor's device type. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.13 | Columncie1000LldpStatusMedRemoteDeviceInfoHwRev | read-only | current | Shows the LLDP neighbor's hardware revision. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.14 | Columncie1000LldpStatusMedRemoteDeviceInfoFwRev | read-only | current | Shows the LLDP neighbor's firmware revision. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.15 | Columncie1000LldpStatusMedRemoteDeviceInfoSwRev | read-only | current | Shows the LLDP neighbor's software revision. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.16 | Columncie1000LldpStatusMedRemoteDeviceInfoSerialNo | read-only | current | Shows the LLDP neighbor's serial number. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.17 | Columncie1000LldpStatusMedRemoteDeviceInfoManufacturerName | read-only | current | Shows the LLDP neighbor's manufacturer name. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.18 | Columncie1000LldpStatusMedRemoteDeviceInfoModelName | read-only | current | Shows the LLDP neighbor's model name. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.19 | Columncie1000LldpStatusMedRemoteDeviceInfoAssetId | read-only | current | Shows the LLDP neighbor's asset id. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.20 | Columncie1000LldpStatusMedRemoteDeviceInfoEeeRxTwSys | read-only | current | Shows the LLDP neighbor's Receive tw_sys_rx . Tw_sys_rx is defined as the time (expressed in microseconds) that the transmitting link partner will wait before … |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.21 | Columncie1000LldpStatusMedRemoteDeviceInfoEeeTxTwSys | read-only | current | Shows the LLDP neighbor's Transmit Tw_sys_tx . Tw_sys_tx is defined as the time (expressed in microseconds) that the receiving link partner is requesting the t… |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.22 | Columncie1000LldpStatusMedRemoteDeviceInfoEeeFbTwSys | read-only | current | Shows the LLDP neighbor's Fallback tw_sys_tx. A receiving link partner may inform the transmitter of an alternate desired Tw_sys_tx. Since a receiving link par… |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.23 | Columncie1000LldpStatusMedRemoteDeviceInfoEeeTxTwSysEcho | read-only | current | Shows the LLDP neighbor's echo transmit Tw. The respective echo values shall be defined as the local link partners reflection (echo) of the remote link partner… |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.24 | Columncie1000LldpStatusMedRemoteDeviceInfoEeeRxTwSysEcho | read-only | current | Shows the LLDP neighbor's echo receive Tw. The respective echo values shall be defined as the local link partners reflection (echo) of the remote link partners… |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2 | Tablecie1000LldpStatusMedRemoteDeviceLocInfoTable | not-accessible | current | This is a table to show the LLDP-MED remote device (neighbor) civic location information for a specific interface. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1 | Rowcie1000LldpStatusMedRemoteDeviceLocInfoEntry | not-accessible | current | Each interface has a set of neighbors information |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.1 | Columncie1000LldpStatusMedRemoteDeviceLocInfoIfIndex | accessible-for-notify | current | Logical interface number index. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.2 | Columncie1000LldpStatusMedRemoteDeviceLocInfoLldpmedIndex | accessible-for-notify | current | Neighbor information table entry index. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.5 | Columncie1000LldpStatusMedRemoteDeviceLocInfoState | read-only | current | National subdivision |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.6 | Columncie1000LldpStatusMedRemoteDeviceLocInfoCounty | read-only | current | County |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.7 | Columncie1000LldpStatusMedRemoteDeviceLocInfoCity | read-only | current | City |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.8 | Columncie1000LldpStatusMedRemoteDeviceLocInfoDistrict | read-only | current | City district |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.9 | Columncie1000LldpStatusMedRemoteDeviceLocInfoBlock | read-only | current | Block (Neighborhood) |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.10 | Columncie1000LldpStatusMedRemoteDeviceLocInfoStreet | read-only | current | Street |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.11 | Columncie1000LldpStatusMedRemoteDeviceLocInfoLeadingStreetDirection | read-only | current | Street Direction |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.12 | Columncie1000LldpStatusMedRemoteDeviceLocInfoTrailingStreetSuffix | read-only | current | Trailing Street Suffix |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.13 | Columncie1000LldpStatusMedRemoteDeviceLocInfoStreetSuffix | read-only | current | Street Suffix |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.14 | Columncie1000LldpStatusMedRemoteDeviceLocInfoHouseNo | read-only | current | House No. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.15 | Columncie1000LldpStatusMedRemoteDeviceLocInfoHouseNoSuffix | read-only | current | House No. Suffix |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.16 | Columncie1000LldpStatusMedRemoteDeviceLocInfoLandmark | read-only | current | Landmark |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.17 | Columncie1000LldpStatusMedRemoteDeviceLocInfoAdditionalInfo | read-only | current | Additional Location Info |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.18 | Columncie1000LldpStatusMedRemoteDeviceLocInfoName | read-only | current | Name |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.19 | Columncie1000LldpStatusMedRemoteDeviceLocInfoZipCode | read-only | current | Zip code |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.20 | Columncie1000LldpStatusMedRemoteDeviceLocInfoBuilding | read-only | current | Building |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.21 | Columncie1000LldpStatusMedRemoteDeviceLocInfoApartment | read-only | current | Apartment/unit |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.22 | Columncie1000LldpStatusMedRemoteDeviceLocInfoFloor | read-only | current | Floor |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.23 | Columncie1000LldpStatusMedRemoteDeviceLocInfoRoomNumber | read-only | current | Room Number |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.24 | Columncie1000LldpStatusMedRemoteDeviceLocInfoPlaceType | read-only | current | Place type |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.25 | Columncie1000LldpStatusMedRemoteDeviceLocInfoPostalCommunityName | read-only | current | Postal Community Name |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.26 | Columncie1000LldpStatusMedRemoteDeviceLocInfoPoBox | read-only | current | Post Office Box |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.27 | Columncie1000LldpStatusMedRemoteDeviceLocInfoAdditionalCode | read-only | current | Additional Code |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.28 | Columncie1000LldpStatusMedRemoteDeviceLocInfoCountryCode | read-only | current | The two-letter ISO 3166 country code in capital ASCII letters - Example: DK, DE or US. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.3 | Tablecie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoTable | not-accessible | current | This is a table to show the LLDP-MED remote device (neighbor) network policies information for a specific interface. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.3.1 | Rowcie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoEntry | not-accessible | current | Each interface has a set of neighbors information |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.3.1.1 | Columncie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoIfIndex | accessible-for-notify | current | Logical interface number index. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.3.1.2 | Columncie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoLldpmedIndex | accessible-for-notify | current | Neighbor information table entry index. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.3.1.3 | Columncie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoLldpmedPolicy | accessible-for-notify | current | Policy index. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.3.1.5 | Columncie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoApplicationType | read-only | current | The LLDP policy application type. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.3.1.6 | Columncie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoUnknownPolicy | read-only | current | Policy indicates that an Endpoint Device wants to explicitly advertise that the policy is required by the device. Can be either Defined or Unknown Unknown: The… |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.3.1.7 | Columncie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoTagged | read-only | current | Defines if LLDP policy uses tagged VLAN. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.3.1.8 | Columncie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoVlanId | read-only | current | The policy VLAN ID. Only valid when policy 'Tagged' is TRUE |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.3.1.9 | Columncie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoL2Priority | read-only | current | Shows the LLDP neighbor's policy L2 priority. |
| 1.3.6.1.4.1.9.9.832.1.34.1.3.4.3.1.10 | Columncie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoDscp | read-only | current | LLDP policy DSCP. |
| 1.3.6.1.4.1.9.9.832.1.34.1.4 | Nodecie1000LldpControl | |||
| 1.3.6.1.4.1.9.9.832.1.34.1.4.1 | Nodecie1000LldpControlStatisticsClear | |||
| 1.3.6.1.4.1.9.9.832.1.34.1.4.1.1 | Tablecie1000LldpControlStatisticsClearTable | not-accessible | current | This is a table to clear LLDP statistics for a specific interface. |
| 1.3.6.1.4.1.9.9.832.1.34.1.4.1.1.1 | Rowcie1000LldpControlStatisticsClearEntry | not-accessible | current | Each interface has a set of statistics counters |
| 1.3.6.1.4.1.9.9.832.1.34.1.4.1.1.1.1 | Columncie1000LldpControlStatisticsClearIfIndex | accessible-for-notify | current | Logical interface number index. |
| 1.3.6.1.4.1.9.9.832.1.34.1.4.1.1.1.2 | Columncie1000LldpControlStatisticsClearStatisticsClear | read-write | current | Set to TRUE to clear the LLDP statistics of an interface. |
| 1.3.6.1.4.1.9.9.832.1.34.1.4.1.2 | Nodecie1000LldpControlStatisticsClearGlobal | |||
| 1.3.6.1.4.1.9.9.832.1.34.1.4.1.2.1 | Scalarcie1000LldpControlStatisticsClearGlobalClear | read-write | current | Set to TRUE to clear the LLDP global statistics. |
| 1.3.6.1.4.1.9.9.832.1.34.2 | Nodecie1000LldpMibConformance | |||
| 1.3.6.1.4.1.9.9.832.1.34.2.1 | Nodecie1000LldpMibCompliances | |||
| 1.3.6.1.4.1.9.9.832.1.34.2.1.1 | Compliancecie1000LldpMibCompliance | current | The compliance statement for the implementation. | |
| 1.3.6.1.4.1.9.9.832.1.34.2.2 | Nodecie1000LldpMibGroups | |||
| 1.3.6.1.4.1.9.9.832.1.34.2.2.1 | Groupcie1000LldpConfigGlobalInfoGroup | current | A collection of objects. | |
| 1.3.6.1.4.1.9.9.832.1.34.2.2.2 | Groupcie1000LldpConfigInfoGroup | current | A collection of objects. | |
| 1.3.6.1.4.1.9.9.832.1.34.2.2.3 | Groupcie1000LldpConfigMedInfoGroup | current | A collection of objects. | |
| 1.3.6.1.4.1.9.9.832.1.34.2.2.4 | Groupcie1000LldpConfigMedPolicyInfoGroup | current | A collection of objects. | |
| 1.3.6.1.4.1.9.9.832.1.34.2.2.5 | Groupcie1000LldpConfigMedPolicyListInfoGroup | current | A collection of objects. | |
| 1.3.6.1.4.1.9.9.832.1.34.2.2.6 | Groupcie1000LldpConfigMedGlobalInfoGroup | current | A collection of objects. | |
| 1.3.6.1.4.1.9.9.832.1.34.2.2.7 | Groupcie1000LldpConfigMedLocationInfInfoGroup | current | A collection of objects. | |
| 1.3.6.1.4.1.9.9.832.1.34.2.2.8 | Groupcie1000LldpConfigMedPolicyRowEditorInfoGroup | current | A collection of objects. | |
| 1.3.6.1.4.1.9.9.832.1.34.2.2.9 | Groupcie1000LldpStatusStatisticsGlobalCountersInfoGroup | current | A collection of objects. | |
| 1.3.6.1.4.1.9.9.832.1.34.2.2.10 | Groupcie1000LldpStatusStatisticsTableInfoGroup | current | A collection of objects. | |
| 1.3.6.1.4.1.9.9.832.1.34.2.2.11 | Groupcie1000LldpStatusNeighborsInfInfoGroup | current | A collection of objects. | |
| 1.3.6.1.4.1.9.9.832.1.34.2.2.12 | Groupcie1000LldpStatusNeighborsMgmtInfInfoGroup | current | A collection of objects. | |
| 1.3.6.1.4.1.9.9.832.1.34.2.2.13 | Groupcie1000LldpStatusMedRemoteDeviceInfoInfoGroup | current | A collection of objects. | |
| 1.3.6.1.4.1.9.9.832.1.34.2.2.14 | Groupcie1000LldpStatusMedRemoteDeviceLocInfoInfoGroup | current | A collection of objects. | |
| 1.3.6.1.4.1.9.9.832.1.34.2.2.15 | Groupcie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoInfoGroup | current | A collection of objects. | |
| 1.3.6.1.4.1.9.9.832.1.34.2.2.16 | Groupcie1000LldpControlStatisticsClearTableInfoGroup | current | A collection of objects. | |
| 1.3.6.1.4.1.9.9.832.1.34.2.2.17 | Groupcie1000LldpControlStatisticsClearGlobalInfoGroup | current | A collection of objects. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| CIE1000lldpAdminState | INTEGER { disabled(0), txAndRx(1), txOnly(2), rxOnly(3) } | current | This enumerations the admin state. |
| CIE1000lldpmedAltitudeType | INTEGER { meters(1), floors(2) } | current | This enumerations the altitude type. |
| CIE1000lldpmedCivicAddressType | INTEGER { state(1), county(2), city(3), district(4), block(5), street(6), leadingStreetDirection(16), trailingStreetSuffix(17), streetSuffix(18), houseNo(19), houseNoSuffix(20), landmark(21), additionalInfo(22), name(23), zipCode(24), building(25), apartment(26), floor(27), roomNumber(28), placeType(29), postalCommunityName(30), poBox(31), additionalCode(32) } | current | This enumerations the civic address type. |
| CIE1000lldpmedDatumType | INTEGER { wgs84(1), nad83navd88(2), nad83mllw(3) } | current | This enumerations the datum (geodetic system). |
| CIE1000lldpmedDeviceType | INTEGER { connectivity(0), endpoint(1) } | current | This enumerations the device type that the device shall operate as. |
| CIE1000lldpmedRemoteDeviceType | INTEGER { notDefined(0), endpointClassI(1), endpointClassII(2), endpointClassIII(3), networkConnectivity(4), reserved(5) } | current | This enumerations the remote neighbor's device type. |
| CIE1000lldpmedRemoteNetworkPolicyApplicationType | INTEGER { voice(1), voiceSignaling(2), guestVoice(3), guestVoiceSignaling(4), softphoneVoice(5), videoConferencing(6), streamingVideo(7), videoSignaling(8) } | current | This enumerations the remote neighbor's network policy's application type. |