CISCO-ADSL-CAP-LINE-MIB
49 objects
This MIB module serves as an enterprise-specific extension of the ADSL-LINE-MIB. The structure of this MIB module shadows the structure of the ADSL-LINE-MIB, table for table. The tables defined by this MIB module contain managed objects that meet the following criteria: 1) A managed object represents an attribute or characteristic specific to CAP (Carrierless AM/PM) modems. 2) The ADSL-CAP-LINE-MIB does not already contain a managed object representing the same information as this managed object. Observe that entries contained by the tables in this MIB module do not augment the corresponding entries in the ADSL-LINE-MIB, as every modem represented by the ADSL-LINE-MIB is not necessarily a CAP modem. Also observe that entries contained by the tables in this MIB module do not augment the corresponding entries in the ADSL-CAP-LINE-MIB, as this assumes that the ADSL-CAP-LINE-MIB defines tables that correspond to every table defined by the ADSL-LINE-MIB. At this time, this assumption does not hold true. *** ABBREVIATIONS, ACRONYMS, AND SYMBOLS *** ADSL - Asymmetric Digital Subscriber Line. ATM - Asynchronous Transfer Mode. ATU-C - ADSL Transceiver Unit, Central Office end. ATU-R - ADSL Transceiver Unit, Remote terminal end. BER - Bit Error Ratio. CAP - Carrierless Amplitude Modulation / Pulse Modulation. DSL - Digital Subscriber Line. SNR - Signal-to-Noise Ratio. STM - Synchronous Transfer Mode. *** DEFINITIONS *** DOWNSTREAM The flow of data in the direction from the ATU-C to ATU-R. MARGIN (also referred to as 'SNR margin') The difference between the SNR of the received signal and the SNR required to provide a BER of 10E-7. SYMBOL The number of bits the transmitter is capable of multiplexing and modulating in a single signalling interval. SYMBOL RATE The rate at which all symbols are transmitted. UPSTREAM The flow of data in the direction from the ATU-R to ATU-C.
Imported Objects
| ADSL-LINE-MIB | adslAtucIntervalNumber adslLineConfProfileName |
| ADSL-TC-MIB | AdslPerfCurrDayCount AdslPerfPrevDayCount |
| CISCO-SMI | ciscoMgmt |
| IF-MIB | ifIndex |
| PerfHist-TC-MIB | PerfCurrentCount PerfIntervalCount |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Gauge32 Integer32 MODULE-IDENTITY OBJECT-TYPE |
| SNMPv2-TC | TEXTUAL-CONVENTION TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.9.149 | IdentityciscoAdslLineCapMIB | for | This MIB module serves as an enterprise-specific extension of the ADSL-LINE-MIB. The structure of this MIB module shadows the structure of the ADSL-LINE-MIB, t… | |
| 1.3.6.1.4.1.9.9.149.1 | NodeciscoAdslLineCapMIBObjects | |||
| 1.3.6.1.4.1.9.9.149.1.2 | TablecAdslAtucCapPhysTable | not-accessible | current | This table extends the adslAtucPhysTable and contains enterprise-specific physical layer parameters for the ATU-C class devices supported by the system. |
| 1.3.6.1.4.1.9.9.149.1.2.1 | RowcAdslAtucCapPhysEntry | not-accessible | current | A set of enterprise-specific physical-layer parameters for an ATU-C class device supported by the system. There exists an entry for each ifEntry with an ifType… |
| 1.3.6.1.4.1.9.9.149.1.2.1.1 | ColumncAdslAtucCapCurrState | read-only | current | This object specifies the state of the ATU-C transceiver. The value of this managed is 'idle' for an ATU-C that has been provisioned, but is not physically pre… |
| 1.3.6.1.4.1.9.9.149.1.2.1.2 | ColumncAdslAtucCapCurrRxGain | read-only | current | This managed object represents the gain applied to the ATU-C receiver. The value of this managed object is '0' for an ATU-C that has been provisioned, but is n… |
| 1.3.6.1.4.1.9.9.149.1.2.1.3 | ColumncAdslAtucCapCurrRxSnr | read-only | current | This managed object represents the signal-to-noise ratio measured across the the ATU-C receive pair. The value of this managed object is '0' for an ATU-C that … |
| 1.3.6.1.4.1.9.9.149.1.3 | TablecAdslAturCapPhysTable | not-accessible | current | This table extends the adslAturPhysTable and contains enterprise-specific physical layer parameters for the ATU-R class devices supported by the system. |
| 1.3.6.1.4.1.9.9.149.1.3.1 | RowcAdslAturCapPhysEntry | not-accessible | current | A set of enterprise-specific physical-layer parameters for an ATU-R class device supported by the system. There exists an entry for each ifEntry with an ifType… |
| 1.3.6.1.4.1.9.9.149.1.3.1.1 | ColumncAdslAturCapCurrRxGain | read-only | current | This managed object represents the gain applied to the ATU-R receiver. The value of this managed object is '0' if the corresponding ATU-C has been provisioned,… |
| 1.3.6.1.4.1.9.9.149.1.6 | TablecAdslAtucCapPerfDataTable | not-accessible | current | This table extends the adslAtucPerfDataTable and contains enterprise-specific physical layer statistics for the ATU-C class devices supported by the system. |
| 1.3.6.1.4.1.9.9.149.1.6.1 | RowcAdslAtucCapPerfDataEntry | not-accessible | current | A set of enterprise-specific physical-layer statistics for an ATU-C class device supported by the system. There exists an entry for each ifEntry with an ifType… |
| 1.3.6.1.4.1.9.9.149.1.6.1.1 | ColumncAdslAtucCapPerfInitFailures | read-only | current | This object specifies the number of line initialization failures relative to sysUpTime. |
| 1.3.6.1.4.1.9.9.149.1.6.1.2 | ColumncAdslAtucCapPerfCurr15MinInitFailures | read-only | current | This object specifies the number of line initialization failures in the current 15-minute interval. |
| 1.3.6.1.4.1.9.9.149.1.6.1.3 | ColumncAdslAtucCapPerfCurr1DayInitFailures | read-only | current | This object specifies the number of line initialization failures in the current 1-day interval. |
| 1.3.6.1.4.1.9.9.149.1.6.1.4 | ColumncAdslAtucCapPerfPrev1DayInitFailures | read-only | current | This object specifies the number of line initialization failures in the previous 1-day interval. |
| 1.3.6.1.4.1.9.9.149.1.8 | TablecAdslAtucCapIntervalTable | not-accessible | current | This table extends the adslAtucIntervalTable and contains enterprise-specific physical layer statistics intervals for the ATU-C class devices supported by the … |
| 1.3.6.1.4.1.9.9.149.1.8.1 | RowcAdslAtucCapIntervalEntry | not-accessible | current | A 15-minute interval of enterprise-specific physical-layer statistics for an ATU-C class device supported by the system. There exists up to 96 entries for each… |
| 1.3.6.1.4.1.9.9.149.1.8.1.1 | ColumncAdslAtucCapIntervalInitFailures | read-only | current | This object specifies the number of line initialization failures in the interval. |
| 1.3.6.1.4.1.9.9.149.1.14 | TablecAdslLineCapConfProfileTable | not-accessible | current | This table extends the adslLineConfProfileTable and contains enterprise-specific ADSL line configuration information. |
| 1.3.6.1.4.1.9.9.149.1.14.1 | RowcAdslLineCapConfProfileEntry | not-accessible | current | A configuration profile containing enterprise-specific ADSL line configuration information. |
| 1.3.6.1.4.1.9.9.149.1.14.1.1 | ColumncAdslLineCapConfTrainingMode | read-create | current | This object specifies the mode employed by the ATU-C and ATU-R when training against each other. One of two training modes can be employed: - Standard An ATU-C… |
| 1.3.6.1.4.1.9.9.149.1.14.1.2 | ColumncAdslLineCapConfInterleaveDelay | read-create | current | This object specifies the interleave delay for the downstream channel. The value of this object specifies the mapping (relative spacing) between subsequent inp… |
| 1.3.6.1.4.1.9.9.149.1.14.1.3 | ColumncAdslLineCapConfCpeSignature | read-create | current | This object specifies the value of the minimum CPE signature expected from ATU-R during training. The value of the CPE signature corresponds to the software ve… |
| 1.3.6.1.4.1.9.9.149.1.14.1.4 | ColumncAdslAtucCapConfTargetSnrMgn | read-create | current | This object specifies the target SNR margin. This is the desired noise margin the ATU-C must achieve with a BER of 10-7 or better to successfully complete trai… |
| 1.3.6.1.4.1.9.9.149.1.14.1.5 | ColumncAdslAtucCapConfMinTxRate | read-create | current | This object specifies the minimum acceptable downstream line rate. |
| 1.3.6.1.4.1.9.9.149.1.14.1.6 | ColumncAdslAtucCapConfMaxTxRate | read-create | current | This object specifies the desired line rate which the ATU-C will attempt to train at. |
| 1.3.6.1.4.1.9.9.149.1.14.1.7 | ColumncAdslAtucCapConfDown136KBaudEnable | read-create | current | This object specifies whether the modem can train the downstream channel using a symbol rate of 136K symbols per second. |
| 1.3.6.1.4.1.9.9.149.1.14.1.8 | ColumncAdslAtucCapConfUp68KBaudEnable | read-create | current | This object specifies whether the modem can train the upstream channel using a symbol rate of 68K symbols per second. The value of this object does not effect … |
| 1.3.6.1.4.1.9.9.149.1.14.1.9 | ColumncAdslAtucCapConfUp17KBaudEnable | read-create | current | This object specifies whether the modem can train the upstream channel using a symbol rate of 17K symbols per second. The value of this object does not effect … |
| 1.3.6.1.4.1.9.9.149.1.14.1.10 | ColumncAdslAtucCapConfPsdmLevel | read-create | current | This managed object specifies the nominal power output of the ATU-C across the entire transmit spectrum. Observe that this implies the attenuation of the signa… |
| 1.3.6.1.4.1.9.9.149.1.14.1.11 | ColumncAdslAturCapConfTargetSnrMgn | read-create | current | This object specifies the target SNR margin. This is the desired noise margin the ATU-R must achieve with a BER of 10-7 or better to successfully complete trai… |
| 1.3.6.1.4.1.9.9.149.1.14.1.12 | ColumncAdslAturCapConfMinTxRate | read-create | current | This object specifies the minimum acceptable upstream line rate. |
| 1.3.6.1.4.1.9.9.149.1.14.1.13 | ColumncAdslAturCapConfMaxTxRate | read-create | current | This object specifies the desired line rate which the ATU-R will attempt to train at. |
| 1.3.6.1.4.1.9.9.149.1.14.1.14 | ColumncAdslAturCapConfPsdmLevel | read-create | current | This managed object specifies the nominal power output of the ATU-R across the entire transmit spectrum. Observe that this implies the attenuation of the signa… |
| 1.3.6.1.4.1.9.9.149.2 | NodecAdslLineCapMIBNotificationsPrefix | |||
| 1.3.6.1.4.1.9.9.149.2.0 | NodecAdslLineCapMIBNotifications | |||
| 1.3.6.1.4.1.9.9.149.3 | NodeciscoAdslLineCapMIBConformance | |||
| 1.3.6.1.4.1.9.9.149.3.1 | NodeciscoAdslLineCapMIBCompliances | |||
| 1.3.6.1.4.1.9.9.149.3.1.1 | ComplianceciscoAdslLineCapMIBAtucCompliance | current | The compliance statement for entities that implement the CISCO-ADSL-CAP-LINE-MIB. Implementation of this MIB is mandatory for any platform that supports one or… | |
| 1.3.6.1.4.1.9.9.149.3.1.2 | ComplianceciscoAdslLineCapMIBAturCompliance | current | The compliance statement for entities that implement the CISCO-ADSL-CAP-LINE-MIB and manage ADSL ATU-R class devices. Implementation of this MIB is mandatory f… | |
| 1.3.6.1.4.1.9.9.149.3.2 | NodeciscoAdslLineCapMIBGroups | |||
| 1.3.6.1.4.1.9.9.149.3.2.1 | GroupcAdslAtucCapBasicGroup | current | A collection of managed objects defining the basic operation of an ATU-C implementing the CAP line code. | |
| 1.3.6.1.4.1.9.9.149.3.2.2 | GroupcAdslAturBasicGroup | current | A collection of managed objects defining the basic operation of an ATU-R implementing the CAP line code. | |
| 1.3.6.1.4.1.9.9.149.3.2.3 | GroupcAdslAturCapGroup | current | A collection of managed objects defining the capability to remotely manage a ATU-R. | |
| 1.3.6.1.4.1.9.9.149.3.2.4 | GroupcAdslAtucCapPM15MinIntervalGroup | current | A collection of managed objects defining near-end performance data collection capability using 15-minute intervals. | |
| 1.3.6.1.4.1.9.9.149.3.2.5 | GroupcAdslAtucCapPM1DayIntervalGroup | current | A collection of managed objects defining near-end performance data collection capability using 1-day intervals. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| AdslLineCapDownstreamRate | INTEGER ( 7168000 | 6272000 | 5120000 | 4480000 | 3200000 | 2688000 | 2560000 | 2240000 | 1920000 | 1600000 | 1280000 | 1024000 | 960000 | 896000 | 768000 | 640000 | 512000 | 384000 | 256000 | 0 ) | current | The downstream line rate at which an ADSL line can train at, given an ATU-C and ATU-R implementing the CAP line code. |
| AdslLineCapUpstreamRate | INTEGER ( 1088000 | 952000 | 816000 | 680000 | 544000 | 408000 | 272000 | 91000 | 0 ) | current | The upstream line rate at which an ADSL line can train at, given an ATU-C and ATU-R implementing the CAP line code. |