CISCO-ATM-TRUNK-MIB
104 objects
The MIB for voice and Nx64 over ATM Trunking applications. The following lists the abbreviations used in this MIB: AAL ATM Adaption Layer AIS Alarm Indication Signal CID Channel Identifier DSP Digital Signal Processing DTMF Dual Tone Multi Frequency FCS Frame Check Sequence TDM Time Division Multiplexing PVC Permanent Virtual Circuit RAI Remote Alarm Indication RDI Remote Defect Indication SID Silence Insertion Descriptor SVC Switched Virtual Circuit VAD Voice Activity Detection VBD Voice Band Data VC Virtual Circuit
Imported Objects
| CISCO-SMI | ciscoMgmt |
| CISCO-TC | BulkConfigResult ConfigIterator |
| CISCO-VOICE-AALX-PROFILE-MIB | CiscoAal2ProfileNumber CiscoAal2ProfileType |
| CISCO-VOICE-COMMON-DIAL-CONTROL-MIB | CvcCoderTypeRate CvcSpeechCoderRate |
| IF-MIB | ifIndex InterfaceIndex |
| RMON-MIB | OwnerString |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Gauge32 Integer32 MODULE-IDENTITY OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | RowStatus TEXTUAL-CONVENTION TimeStamp TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.9.351 | IdentityciscoAtmTrunkMIB | The MIB for voice and Nx64 over ATM Trunking applications. The following lists the abbreviations used in this MIB: AAL ATM Adaption Layer AIS Alarm Indication … | ||
| 1.3.6.1.4.1.9.9.351.0 | NodecAtmTrunkMIBNotifications | |||
| 1.3.6.1.4.1.9.9.351.1 | NodecAtmTrunkMIBObjects | |||
| 1.3.6.1.4.1.9.9.351.1.1 | NodecAtmTrunkCidConfig | |||
| 1.3.6.1.4.1.9.9.351.1.1.1 | TablecatmtCidTable | not-accessible | current | This table is used to establish the mapping of one or more DS0 channels from a single DS1 interface to an AAL2 connection identified by a Channel IDentificatio… |
| 1.3.6.1.4.1.9.9.351.1.1.1.1 | RowcatmtCidEntry | not-accessible | current | An entry in the catmtCidTable. Each entry represents an AAL2 trunking connection which is uniquely identified by the PVC index and the CID number. An AAL2 trun… |
| 1.3.6.1.4.1.9.9.351.1.1.1.1.1 | ColumncatmtCidVpi | not-accessible | current | This object is the VPI value of an ATM PVC connection. |
| 1.3.6.1.4.1.9.9.351.1.1.1.1.2 | ColumncatmtCidVci | not-accessible | current | This object is the VCI value of an ATM PVC connection. |
| 1.3.6.1.4.1.9.9.351.1.1.1.1.3 | ColumncatmtCid | not-accessible | current | This object is the CID of an ATM AAL2 connection, it is unique within a PVC or SVC connection. The CID number at both sides of an AAL2 connection must be the s… |
| 1.3.6.1.4.1.9.9.351.1.1.1.1.4 | ColumncatmtCidDs1 | read-create | current | The value of this object equals to the 'ifIndex' of the DS1 interface. This object is mandatory when adding a CID entry. Once a CID entry is added, this object… |
| 1.3.6.1.4.1.9.9.351.1.1.1.1.5 | ColumncatmtCidDs0GroupIndex | read-create | current | An arbitrary index that uniquely identifies a DS0 group which contains one or more DS0(s) within a DS1 interface specified by 'catmtCidDs1'. This object is man… |
| 1.3.6.1.4.1.9.9.351.1.1.1.1.6 | ColumncatmtCidProfileType | read-create | current | This object specifies the type of the AAL2 CODEC profile. The combination of the profile type and profile number specified by 'catmtCidProfileNumber' defines a… |
| 1.3.6.1.4.1.9.9.351.1.1.1.1.7 | ColumncatmtCidProfileNumber | read-create | current | This object specifies the AAL2 CODEC profile number. The combination of profile type and profile number defines an AAL2 CODEC profile. A profile contains one o… |
| 1.3.6.1.4.1.9.9.351.1.1.1.1.8 | ColumncatmtCidVoiceCodec | read-create | current | This object specifies the CODEC type used for the AAL2 trunking connection. The following table lists the CODEC types specified in each profile table by ITU I.… |
| 1.3.6.1.4.1.9.9.351.1.1.1.1.9 | ColumncatmtCidVBDCodec | read-create | current | This object specifies the CODEC type to be used for Voice Band Data (VBD) upspeed. Upspeed is to change the transmission rate of a voice interface to a higher … |
| 1.3.6.1.4.1.9.9.351.1.1.1.1.10 | ColumncatmtCidNx64Enable | read-create | current | This object specifies whether a CID entry is in the Nx64 packet stream mode. When this object is set to 'false', the CID connection is for voice trunking appli… |
| 1.3.6.1.4.1.9.9.351.1.1.1.1.11 | ColumncatmtCidNx64Profile | read-create | current | This object specifies the Nx64 data profile for an AAL2 data trunking connection. The value of this object is a valid index of the cdapNx64ProfileTable in the … |
| 1.3.6.1.4.1.9.9.351.1.1.1.1.12 | ColumncatmtCidStateBitMap | read-only | current | This object is used to indicate the state of the CID. All bits setting to 0 which means status 'okay'. |
| 1.3.6.1.4.1.9.9.351.1.1.1.1.13 | ColumncatmtCidRepetition | read-create | current | This object is used to repeatedly apply the writable objects of catmtCidTable specified in the same SNMP PDU starting from the row defined by the index object … |
| 1.3.6.1.4.1.9.9.351.1.1.1.1.14 | ColumncatmtCidRepetitionOwner | read-create | current | This object is used for error reporting of the bulk provisioning operation specified by catmtCidRepetition. The value of this object is set by the SNMP manager… |
| 1.3.6.1.4.1.9.9.351.1.1.1.1.15 | ColumncatmtCidRepetitionResult | read-only | current | This object indicates the result of the bulk provisioning specified in catmtCidRepetition. The format might look at (but not limited to): 'COMPLETION=<number o… |
| 1.3.6.1.4.1.9.9.351.1.1.1.1.16 | ColumncatmtCidRowStatus | read-create | current | This object is used for adding/deleting the entries from the catmtCidTable. In order to create a CID entry, the following parameters are mandatory and must be … |
| 1.3.6.1.4.1.9.9.351.1.2 | NodecAtmTrunkCidConnStats | |||
| 1.3.6.1.4.1.9.9.351.1.2.1 | TablecatmtCidStatsTable | not-accessible | current | This table contains the statistical information on a per CID connection basis for AAL2 Trunking applications. |
| 1.3.6.1.4.1.9.9.351.1.2.1.1 | RowcatmtCidStatsEntry | not-accessible | current | This table contains statistical information for an AAL2 connection. Each entry in this table corresponds to an AAL2 bearer connection that has been setup by ma… |
| 1.3.6.1.4.1.9.9.351.1.2.1.1.1 | ColumncatmtCidSentPackets | read-only | current | This object indicates the number of packets sent towards network side since the connection setup. |
| 1.3.6.1.4.1.9.9.351.1.2.1.1.2 | ColumncatmtCidRcvdPackets | read-only | current | This object indicates the count of packets received from network side since the connection setup. |
| 1.3.6.1.4.1.9.9.351.1.2.1.1.3 | ColumncatmtCidSentOctets | read-only | current | This object indicates the count of bytes sent towards network side since connection setup. |
| 1.3.6.1.4.1.9.9.351.1.2.1.1.4 | ColumncatmtCidRcvdOctets | read-only | current | This object indicates the count of bytes received from network since connection setup. |
| 1.3.6.1.4.1.9.9.351.1.2.1.1.5 | ColumncatmtCidLostPackets | read-only | current | This object indicates the count of packets lost in the egress direction (from the network). This number is computed based on the expected number of packets and… |
| 1.3.6.1.4.1.9.9.351.1.2.1.1.6 | ColumncatmtCidJitter | read-only | current | This object indicates the jitter (a.k.a interarrival jitter). This value is determined by the gateway DSP and obtained by the processor running on gateway upon… |
| 1.3.6.1.4.1.9.9.351.1.2.1.1.7 | ColumncatmtCidExtAISCnts | read-only | current | This object contains the number of external AIS AAL2 Type3 packets received. External AIS : alarm indication signal associated with a maintenance alarm detecte… |
| 1.3.6.1.4.1.9.9.351.1.2.1.1.8 | ColumncatmtCidExtRAICnts | read-only | current | This object contains the number of external RAI AAL2 Type3 packets received. External RAI is transmitted upstream from an entity that has detected defects pers… |
| 1.3.6.1.4.1.9.9.351.1.2.1.1.9 | ColumncatmtCidConnAISCnts | read-only | current | This object contains the number of external connection AIS AAL2 packets received. External Conn AIS is a Alarm Indicating Signal transmitted in the downstream … |
| 1.3.6.1.4.1.9.9.351.1.2.1.1.10 | ColumncatmtCidConnRDICnts | read-only | current | This object contains the number of external connection RDI AAL2 packets received. External Connection RDI - is a signal transmitted in the upstream direction b… |
| 1.3.6.1.4.1.9.9.351.1.2.1.1.11 | ColumncatmtCidNx64FramesTxToTDM | read-only | current | This object contains the number of frames transmitted to the TDM interface. This object is only applicable when catmtCidNx64Mode is set to to 'hdlc'. |
| 1.3.6.1.4.1.9.9.351.1.2.1.1.12 | ColumncatmtCidNx64FramesRxFromTDM | read-only | current | This object contains the number of frames received from the TDM interface. This object is only applicable when catmtCidNx64Mode is set to to 'hdlc'. |
| 1.3.6.1.4.1.9.9.351.1.2.1.1.13 | ColumncatmtCidNx64EncBytesTxToTDM | read-only | current | This object contains the number of encoded bytes transmitted to the TDM interface. |
| 1.3.6.1.4.1.9.9.351.1.2.1.1.14 | ColumncatmtCidNx64EncBytesRxFromTDM | read-only | current | This object contains the number of encoded bytes received from the TDM interface. |
| 1.3.6.1.4.1.9.9.351.1.2.1.1.15 | ColumncatmtCidNx64InvalidFCSFrames | read-only | current | This object contains the number of invalid frames received with invalid Frame Check Sequence (FCS) error. This object is only applicable when catmtCidNx64Mode … |
| 1.3.6.1.4.1.9.9.351.1.2.1.1.16 | ColumncatmtCidNx64AbortSeqFrames | read-only | current | This object contains the number of invalid frames received with invalid frame abort sequence error. This object is only applicable when catmtCidNx64Mode is set… |
| 1.3.6.1.4.1.9.9.351.1.2.1.1.17 | ColumncatmtCidNx64InvalidShortFrames | read-only | current | This object contains the number of invalid short frames (length less than minimum length) received. This object is only applicable when catmtCidNx64Mode is set… |
| 1.3.6.1.4.1.9.9.351.1.2.1.1.18 | ColumncatmtCidNx64InvalidLongFrames | read-only | current | This object contains the number of invalid long frames (length greater than maximum length) received. This object is only applicable when catmtCidNx64Mode is s… |
| 1.3.6.1.4.1.9.9.351.1.2.1.1.19 | ColumncatmtCidNx64NoByteAlignErrorFrames | read-only | current | This object contains the number of invalid frames received with no byte alignment. This object is only applicable when catmtCidNx64Mode is set to to 'hdlc'. |
| 1.3.6.1.4.1.9.9.351.1.2.1.1.20 | ColumncatmtCidNx64RASTimeOutFrames | read-only | current | This object contains the number of frames received with RAS timer timeout. This object is only applicable when catmtCidNx64Mode is set to to 'hdlc'. |
| 1.3.6.1.4.1.9.9.351.1.2.1.1.21 | ColumncatmtCidLastResetTime | read-only | current | This object contains the value of sysUpTime when the last counter reset occurred. If no counter reset has occurred since the last time connection is establishe… |
| 1.3.6.1.4.1.9.9.351.1.2.1.1.22 | ColumncatmtCidCounterClear | read-write | current | When this object is set to value of true(1), all statistics counters with type of Counter32SinceReset in the table catmtCidStatsTable will be reset to zero. Se… |
| 1.3.6.1.4.1.9.9.351.1.3 | NodecAtmTrunkAal1Config | |||
| 1.3.6.1.4.1.9.9.351.1.3.1 | TablecatmtAal1Table | not-accessible | current | This table is used to establish the mapping of a DS0 to an AAL1 ATM connection. This table is created and used for ATM AAL1 trunking applications only. |
| 1.3.6.1.4.1.9.9.351.1.3.1.1 | RowcatmtAal1Entry | not-accessible | current | An entry in the catmtAal1Table. Each entry represents an AAL1 trunking connection which is uniquely identified by the PVC index. An AAL1 trunking connection is… |
| 1.3.6.1.4.1.9.9.351.1.3.1.1.1 | ColumncatmtAal1Vpi | not-accessible | current | This object is the VPI value of an ATM PVC connection. |
| 1.3.6.1.4.1.9.9.351.1.3.1.1.2 | ColumncatmtAal1Vci | not-accessible | current | This object is the VCI value of an ATM PVC connection. |
| 1.3.6.1.4.1.9.9.351.1.3.1.1.3 | ColumncatmtAal1Ds1 | read-create | current | The value of this object is equivalent to the 'ifIndex' of the DS1 interface. This object is mandatory when adding an AAL1 entry. Once an AAL1 entry is added, … |
| 1.3.6.1.4.1.9.9.351.1.3.1.1.4 | ColumncatmtAal1Ds0GroupIndex | read-create | current | An arbitrary index that uniquely identifies one or a group of DS0s to be connected to an AAL1 trunking connection. When catmtAal1Nx64Enable is set to 'false', … |
| 1.3.6.1.4.1.9.9.351.1.3.1.1.5 | ColumncatmtAal1Nx64Profile | read-create | current | This object specifies the Nx64 AAL1 data profile for an AAL1 trunking connection. The value of this object is a valid index of cdapNx64Aal1ProfileTable in CISC… |
| 1.3.6.1.4.1.9.9.351.1.3.1.1.6 | ColumncatmtAal1RowStatus | read-create | current | This object is used for adding/deleting the entries from the catmtAal1Table. In order to create an AAL1 trunking entry, the following parameters are mandatory … |
| 1.3.6.1.4.1.9.9.351.1.4 | NodecAtmTrunkAal1ConnStats | |||
| 1.3.6.1.4.1.9.9.351.1.4.1 | TablecatmtAal1StatsTable | not-accessible | current | This table contains the statistics information on a per AAL1 connection basis for ATM AAL1 Trunking applications. |
| 1.3.6.1.4.1.9.9.351.1.4.1.1 | RowcatmtAal1StatsEntry | not-accessible | current | This table contains statistics information for an AAL1 trunking connection. Each entry in this table corresponds to an AAL1 connection that has been setup by b… |
| 1.3.6.1.4.1.9.9.351.1.4.1.1.1 | ColumncatmtAal1TxCells | read-only | current | This object contains the number of ATM AAL1 cells transmitted from gateway to ATM network. |
| 1.3.6.1.4.1.9.9.351.1.4.1.1.2 | ColumncatmtAal1RxCells | read-only | current | This object contains the number of ATM AAL1 cells gateway has received from ATM network. |
| 1.3.6.1.4.1.9.9.351.1.4.1.1.3 | ColumncatmtAal1TxPayloadBytes | read-only | current | This object contains the number of payload bytes transmitted from gateway to ATM network. |
| 1.3.6.1.4.1.9.9.351.1.4.1.1.4 | ColumncatmtAal1RxPayloadBytes | read-only | current | This object contains the number of payload bytes gateway has received from ATM network. |
| 1.3.6.1.4.1.9.9.351.1.4.1.1.5 | ColumncatmtAal1Jitter | read-only | current | This object indicates the jitter (a.k.a interarrival jitter). The value of this object is determined by the gateway DSP and obtained by the processor running o… |
| 1.3.6.1.4.1.9.9.351.1.4.1.1.6 | ColumncatmtAal1LastResetTime | read-only | current | This object contains the value of sysUpTime when the last counter reset occurred. If no counter reset has occurred since the last time system is up, this objec… |
| 1.3.6.1.4.1.9.9.351.1.4.1.1.7 | ColumncatmtAal1CounterClear | read-write | current | When this object is set to value of true(1), all statistics counters with type of Counter32SinceReset in the table catmtAal1StatsTable will be reset to zero. S… |
| 1.3.6.1.4.1.9.9.351.1.5 | NodecAtmTrunkAal5Config | |||
| 1.3.6.1.4.1.9.9.351.1.5.1 | TablecatmtAal5Table | not-accessible | current | This table is used to establish the mapping of a DS0 to an AAL5 ATM connection. This table is created and used for ATM AAL5 trunking applications only. |
| 1.3.6.1.4.1.9.9.351.1.5.1.1 | RowcatmtAal5Entry | not-accessible | current | An entry in the catmtAal5Table. Each entry represents an AAL5 trunking connection which is uniquely identified by the PVC index. An AAL5 trunking connection is… |
| 1.3.6.1.4.1.9.9.351.1.5.1.1.1 | ColumncatmtAal5Vpi | not-accessible | current | This object is the VPI value of an ATM PVC connection. |
| 1.3.6.1.4.1.9.9.351.1.5.1.1.2 | ColumncatmtAal5Vci | not-accessible | current | This object is the VCI value of an ATM PVC connection. |
| 1.3.6.1.4.1.9.9.351.1.5.1.1.3 | ColumncatmtAal5Ds1 | read-create | current | The value of this object equals to the 'ifIndex' of the DS1 interface. This object is mandatory when adding an AAL5 entry. Once an AAL5 entry is added, this ob… |
| 1.3.6.1.4.1.9.9.351.1.5.1.1.4 | ColumncatmtAal5Ds0GroupIndex | read-create | current | An arbitrary index that uniquely identifies a DS0 group containing one or more DS0 that connect to an AAL5 trunking connection. This object is mandatory when a… |
| 1.3.6.1.4.1.9.9.351.1.5.1.1.5 | ColumncatmtAal5Nx64Profile | read-create | current | This object specifies the Nx64 data profile for an AAL5 trunking connection. The value of this object is a valid index of the cdapNx64ProfileTable in CISCO-DAT… |
| 1.3.6.1.4.1.9.9.351.1.5.1.1.6 | ColumncatmtAal5RowStatus | read-create | current | This object is used for adding/deleting the entries from the catmtAal5Table. In order to create an AAL5 trunking entry, the following parameters are mandatory … |
| 1.3.6.1.4.1.9.9.351.1.6 | NodecAtmTrunkAal5ConnStats | |||
| 1.3.6.1.4.1.9.9.351.1.6.1 | TablecatmtAal5StatsTable | not-accessible | current | This table contains the statistical information on a per AAL5 connection basis for ATM AAL5 Trunking applications. |
| 1.3.6.1.4.1.9.9.351.1.6.1.1 | RowcatmtAal5StatsEntry | not-accessible | current | This table contains statistical information for an AAL5 trunking connection. Each entry in this table corresponds to an AAL5 connection that has been setup by … |
| 1.3.6.1.4.1.9.9.351.1.6.1.1.1 | ColumncatmtAal5SentPackets | read-only | current | This object indicates the number of packets sent towards network side since the connection is up. |
| 1.3.6.1.4.1.9.9.351.1.6.1.1.2 | ColumncatmtAal5RcvdPackets | read-only | current | This object indicates the count of packets received from network side since the connection setup. |
| 1.3.6.1.4.1.9.9.351.1.6.1.1.3 | ColumncatmtAal5SentOctets | read-only | current | This object indicates the count of bytes sent towards network side since connection setup. |
| 1.3.6.1.4.1.9.9.351.1.6.1.1.4 | ColumncatmtAal5RcvdOctets | read-only | current | This object indicates the count of bytes received from network since connection setup. |
| 1.3.6.1.4.1.9.9.351.1.6.1.1.5 | ColumncatmtAal5FramesTxToTDM | read-only | current | This object contains the number of frames transmitted to the TDM interface. This object is only applicable when catmtAal5Nx64Mode is set to to 'hdlc'. |
| 1.3.6.1.4.1.9.9.351.1.6.1.1.6 | ColumncatmtAal5FramesRxFromTDM | read-only | current | This object contains the number of frames received from the TDM interface. This object is only applicable when catmtAal5Nx64Mode is set to to 'hdlc'. |
| 1.3.6.1.4.1.9.9.351.1.6.1.1.7 | ColumncatmtAal5EncBytesTxToTDM | read-only | current | This object contains the number of encoded bytes transmitted to the TDM interface. |
| 1.3.6.1.4.1.9.9.351.1.6.1.1.8 | ColumncatmtAal5EncBytesRxFromTDM | read-only | current | This object contains the number of encoded bytes received from TDM interface. |
| 1.3.6.1.4.1.9.9.351.1.6.1.1.9 | ColumncatmtAal5InvalidFCSFrames | read-only | current | This object contains the number of invalid frames received with invalid Frame Check Sequence (FCS) error. This object is only applicable when catmtAal5Nx64Mode… |
| 1.3.6.1.4.1.9.9.351.1.6.1.1.10 | ColumncatmtAal5AbortSeqFrames | read-only | current | This object contains the number of invalid frames received with invalid frame abort sequence error. This object is only applicable when catmtAal5Nx64Mode is se… |
| 1.3.6.1.4.1.9.9.351.1.6.1.1.11 | ColumncatmtAal5InvalidShortFrames | read-only | current | This object contains the number of invalid short frames (length less than minimum length) received. This object is only applicable when catmtAal5Nx64Mode is se… |
| 1.3.6.1.4.1.9.9.351.1.6.1.1.12 | ColumncatmtAal5InvalidLongFrames | read-only | current | This object contains the number of invalid long frames (length greater than maximum length) received. This object is only applicable when catmtAal5Nx64Mode is … |
| 1.3.6.1.4.1.9.9.351.1.6.1.1.13 | ColumncatmtAal5NoByteAlignErrorFrames | read-only | current | This object contains the number of invalid frames received with no byte alignment. This object is only applicable when catmtAal5Nx64Mode is set to to 'hdlc'. |
| 1.3.6.1.4.1.9.9.351.1.6.1.1.14 | ColumncatmtAal5LastResetTime | read-only | current | This object contains the value of sysUpTime when the last counter reset occurred. If no counter reset has occurred since the last time system is up, this objec… |
| 1.3.6.1.4.1.9.9.351.1.6.1.1.15 | ColumncatmtAal5CounterClear | read-write | current | When this object is set to value of true(1), all statistics counters with type of Counter32SinceReset in the table catmtAal5StatsTable will be reset to zero. S… |
| 1.3.6.1.4.1.9.9.351.2 | NodecAtmTrunkMIBConformance | |||
| 1.3.6.1.4.1.9.9.351.2.1 | NodecAtmTrunkMIBCompliances | |||
| 1.3.6.1.4.1.9.9.351.2.1.1 | CompliancecAtmTrunkMIBCompliance | current | Compliance statement for CISCO-VOICE-ATM-TRUNK-MIB. | |
| 1.3.6.1.4.1.9.9.351.2.2 | NodecAtmTrunkMIBGroups | |||
| 1.3.6.1.4.1.9.9.351.2.2.1 | GroupcAtmTrunkCidMIBGroup | current | This group contains objects related to ATM AAL2 trunking CID level parameters. | |
| 1.3.6.1.4.1.9.9.351.2.2.2 | GroupcAtmTrunkAal1MIBGroup | current | This group contains objects related to ATM AAL1 trunking parameters. | |
| 1.3.6.1.4.1.9.9.351.2.2.3 | GroupcAtmTrunkAal5MIBGroup | current | This group contains objects related to ATM AAL5 trunking parameters. | |
| 1.3.6.1.4.1.9.9.351.2.2.4 | GroupcAtmTrunkCidConnStatsMIBGroup | current | This group contains objects for AAL2 bearer connection statistics information used for ATM AAL2 trunking. | |
| 1.3.6.1.4.1.9.9.351.2.2.5 | GroupcAtmTrunkAal1ConnStatsMIBGroup | current | This group contains objects for AAL1 connection statistics information used for ATM AAL1 trunking. | |
| 1.3.6.1.4.1.9.9.351.2.2.6 | GroupcAtmTrunkAal5ConnStatsMIBGroup | current | This group contains objects for AAL5 bearer connection statistics information used for ATM AAL5 trunking. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| Counter32SinceReset | Unsigned32 (0..2147483647) | current | This textual convention defines a counter type that is similar to Counter32 but can be reset. The value of the objects of this type indicates the statistics since last counter reset. Once the value of the counter object… |