CISCO-IDSL-LINE-MIB
152 objects
This MIB module describes IDSL (ISDN Digital Line Subscriber) line interfaces. The structure of this module resembles that of the ADSL-LINE-MIB (RFC-2662). Observe that the tables in this module do not necessarily extend the tables defined by the ADSL-LINE-MIB. Currently, only those tables that contain configuration information extend the profile tables defined by the ADSL-LINE-MIB. This allows the management client to define xDSL configuration profiles that apply across all xDSL modems, independent of the technology being utilized by the modem. *** ABBREVIATIONS, ACRONYMS, AND SYMBOLS *** ADSL - Asymmetric Digital Subscriber Line. ATM - Asynchronous Transfer Mode. BRITE - Basic Rate Interface Terminal Extender. CV - Coding Violation. DLC - Data Link Connection. DSL - Digital Subscriber Line. ES - Error Second. IDSL - IDSN Digital Subscriber Loop. ITU-C - IDSL Transceiver Unit, Central Office end. ITU-R - IDSL Transceiver Unit, Remote terminal end. LMI - Link Management Interface. LOF - Loss Of Frame. LOS - Loss Of Signal. NT - Network Terminator. PPP - Point-to-Point Protocol. PPPoA - PPP over ATM. SES - Severely Errored Second. *** DEFINITIONS *** CODING VIOLATION A coding violation occurs when the incoming signal exhibits a CRC anomaly. DOWNSTREAM The flow of data in the direction from the ITU-C to ITU-R. ERRORED SECOND A second with one or more coding violations. LINE RATE The total data rate supported by a line. Observe that the payload rate is equal the line rate for the earliest implementations of IDSL. However, the payload rate maybe less than the line rate for future implementations. SEVERELY ERRORED SECOND A second with 3 or more coding violations. UPSTREAM The flow of data in the direction from the ATU-R to ATU-C.
Imported Objects
| ADSL-LINE-MIB | adslLineAlarmConfProfileName adslLineConfProfileName |
| CISCO-SMI | ciscoMgmt |
| IF-MIB | ifIndex InterfaceIndex |
| PerfHist-TC-MIB | PerfCurrentCount PerfIntervalCount |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Gauge32 Integer32 MODULE-IDENTITY OBJECT-TYPE |
| SNMPv2-TC | TEXTUAL-CONVENTION TruthValue VariablePointer |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.9.154 | IdentityciscoIdslLineMIB | This MIB module describes IDSL (ISDN Digital Line Subscriber) line interfaces. The structure of this module resembles that of the ADSL-LINE-MIB (RFC-2662). Obs… | ||
| 1.3.6.1.4.1.9.9.154.1 | NodeciscoIdslLineMIBObjects | |||
| 1.3.6.1.4.1.9.9.154.1.1 | TablecIdslLineTable | not-accessible | current | This table contains the common attributes describing both ends of IDSL lines supported by the system. |
| 1.3.6.1.4.1.9.9.154.1.1.1 | RowcIdslLineEntry | not-accessible | current | A set of common attributes describing both ends of an IDSL line supported by the system. There exists an entry for each ifEntry with an ifType of idsl(154). |
| 1.3.6.1.4.1.9.9.154.1.1.1.1 | ColumncIdslLineSpecific | read-only | current | This object specifies an object identifier of an instance of an object in the MIB. The implementation determines the application of this object. For example, a… |
| 1.3.6.1.4.1.9.9.154.1.1.1.2 | ColumncIdslLineConfProfile | read-write | current | This object specifies the row in the adslLineConfProfileTable (see the ADSL-LINE-MIB for further details), which applies for this IDSL line interface. In the c… |
| 1.3.6.1.4.1.9.9.154.1.1.1.3 | ColumncIdslLineAlarmConfProfile | read-write | current | This object specifies the row in the adslLineAlarmConfProfileTable (see the ADSL-LINE-MIB for further details), which applies for this IDSL line interface. In … |
| 1.3.6.1.4.1.9.9.154.1.2 | TablecIdslItucPhysTable | not-accessible | current | This table contains physical-layer parameters for ITU-C class devices supported by the system. |
| 1.3.6.1.4.1.9.9.154.1.2.1 | RowcIdslItucPhysEntry | not-accessible | current | A set of physical-layer parameters for an ITU-C class device supported by the system. There exists an entry for each ifEntry with an ifType of idsl(154). |
| 1.3.6.1.4.1.9.9.154.1.2.1.1 | ColumncIdslItucInvSerialNumber | read-only | current | This object specifies the vendor specific string that identifies the vendor ITU-C. |
| 1.3.6.1.4.1.9.9.154.1.2.1.2 | ColumncIdslItucInvVendorId | read-only | current | This object specifies the vendor identifier assigned according to ANSI T1.220. |
| 1.3.6.1.4.1.9.9.154.1.2.1.3 | ColumncIdslItucInvVersionNumber | read-only | current | This object specifies the vendor specific version number of the ITU-C. |
| 1.3.6.1.4.1.9.9.154.1.2.1.4 | ColumncIdslItucStatus | read-only | current | This object specifies the state of the ITU-C transceiver: - loopDown The IDSL link is down, as a result of a near-end has detected a LOS, a LOF, has not exchan… |
| 1.3.6.1.4.1.9.9.154.1.6 | TablecIdslItucPerfDataTable | not-accessible | current | This table contains physical-layer statistics for ITU-C class devices supported by the system. |
| 1.3.6.1.4.1.9.9.154.1.6.1 | RowcIdslItucPerfDataEntry | not-accessible | current | A set of physical-layer statistics for an ITU-C class device supported by the system. There exists an entry for each ifEntry with an ifType of idsl(154). |
| 1.3.6.1.4.1.9.9.154.1.6.1.1 | ColumncIdslItucPerfCVs | read-only | current | This object specifies the number of coding violations experienced by the ITU-C since agent reset. |
| 1.3.6.1.4.1.9.9.154.1.6.1.2 | ColumncIdslItucPerfESs | read-only | current | This object specifies the number of errored seconds experienced by the ITU-C since agent reset. |
| 1.3.6.1.4.1.9.9.154.1.6.1.3 | ColumncIdslItucPerfSESs | read-only | current | This object specifies the number of severely errored seconds experienced by the ITU-C since agent reset. |
| 1.3.6.1.4.1.9.9.154.1.6.1.4 | ColumncIdslItucPerfHdlcCVs | read-only | current | This object specifies the number of HDLC coding violations experienced by the ITU-C since agent reset. |
| 1.3.6.1.4.1.9.9.154.1.6.1.5 | ColumncIdslItucPerfHdlcAborts | read-only | current | This object specifies the number of HDLC aborts experienced by the ITU-C since agent reset. |
| 1.3.6.1.4.1.9.9.154.1.6.1.6 | ColumncIdslItucPerfHdlcAligns | read-only | current | This object specifies the number of HDLC frames received by the ITU-C with a non-integral number of octets since agent reset. |
| 1.3.6.1.4.1.9.9.154.1.6.1.7 | ColumncIdslItucPerfHdlcShorts | read-only | current | This object specifies the number of short HDLC frames received by the ITU-C since agent reset. A short HDLC frame contains less than 5 octets. |
| 1.3.6.1.4.1.9.9.154.1.6.1.8 | ColumncIdslItucPerfHdlcLongs | read-only | current | This object specifies the number of long HDLC frames received by the ITU-C since agent reset. A long HDLC frame contains more than 1500 octets. |
| 1.3.6.1.4.1.9.9.154.1.6.1.9 | ColumncIdslItucPerfValidIntervals | read-only | current | The number of previous near-end performance data 15-minute intervals for which data was collected. The value will be <n> unless the measurement was (re-)starte… |
| 1.3.6.1.4.1.9.9.154.1.6.1.10 | ColumncIdslItucPerfInvalidIntervals | read-only | current | The number of near-end performance data 15-minute intervals in the range from 0 to cSdslStucPerfValidIntervals for which no data is available. This object will… |
| 1.3.6.1.4.1.9.9.154.1.6.1.11 | ColumncIdslItucPerfCurr15MinElapsed | read-only | current | The number of seconds that have elapsed since the beginning of the current measurement period. If, for some reason, such as an adjustment in the system's time-… |
| 1.3.6.1.4.1.9.9.154.1.6.1.12 | ColumncIdslItucPerfCurr15MinCVs | read-only | current | This object specifies the number of coding violations experienced by the ITU-C in the current 15-minute interval. |
| 1.3.6.1.4.1.9.9.154.1.6.1.13 | ColumncIdslItucPerfCurr15MinESs | read-only | current | This object specifies the number of errored seconds experienced by the ITU-C in the current 15-minute interval. |
| 1.3.6.1.4.1.9.9.154.1.6.1.14 | ColumncIdslItucPerfCurr15MinSESs | read-only | current | This object specifies the number of severely errored seconds experienced by the ITU-C in the current 15-minute interval. |
| 1.3.6.1.4.1.9.9.154.1.6.1.15 | ColumncIdslItucPerfCurr15MinHdlcCVs | read-only | current | This object specifies the number of HDLC coding violations experienced by the ITU-C in the current 15-minute interval. |
| 1.3.6.1.4.1.9.9.154.1.6.1.16 | ColumncIdslItucPerfCurr15MinHdlcAborts | read-only | current | This object specifies the number of HDLC aborts experienced by the ITU-C in the current 15-minute interval. |
| 1.3.6.1.4.1.9.9.154.1.6.1.17 | ColumncIdslItucPerfCurr15MinHdlcAligns | read-only | current | This object specifies the number of HDLC frames received by the ITU-C with a non-integral number of octets in the current 15-minute interval. |
| 1.3.6.1.4.1.9.9.154.1.6.1.18 | ColumncIdslItucPerfCurr15MinHdlcShorts | read-only | current | This object specifies the number of short HDLC frames received by the ITU-C since agent in the current 15-minute interval. A short HDLC frame contains less tha… |
| 1.3.6.1.4.1.9.9.154.1.6.1.19 | ColumncIdslItucPerfCurr15MinHdlcLongs | read-only | current | This object specifies the number of long HDLC frames received by the ITU-C since agent in the current 15-minute interval. A long HDLC frame contains more than … |
| 1.3.6.1.4.1.9.9.154.1.6.1.20 | ColumncIdslItucPerfCurr1DayElapsed | read-only | current | The number of seconds that have elapsed since the beginning of the current measurement period. If, for some reason, such as an adjustment in the system's time-… |
| 1.3.6.1.4.1.9.9.154.1.6.1.21 | ColumncIdslItucPerfCurr1DayCVs | read-only | current | This object specifies the number of coding violations experienced by the ITU-C in the current 1-day interval. |
| 1.3.6.1.4.1.9.9.154.1.6.1.22 | ColumncIdslItucPerfCurr1DayESs | read-only | current | This object specifies the number of errored seconds experienced by the ITU-C in the current 1-day interval. |
| 1.3.6.1.4.1.9.9.154.1.6.1.23 | ColumncIdslItucPerfCurr1DaySESs | read-only | current | This object specifies the number of severely errored seconds experienced by the ITU-C in the current 1-day interval. |
| 1.3.6.1.4.1.9.9.154.1.6.1.24 | ColumncIdslItucPerfCurr1DayHdlcCVs | read-only | current | This object specifies the number of HDLC coding violations experienced by the ITU-C in the current 1-day interval. |
| 1.3.6.1.4.1.9.9.154.1.6.1.25 | ColumncIdslItucPerfCurr1DayHdlcAborts | read-only | current | This object specifies the number of HDLC aborts experienced by the ITU-C in the current 1-day interval. |
| 1.3.6.1.4.1.9.9.154.1.6.1.26 | ColumncIdslItucPerfCurr1DayHdlcAligns | read-only | current | This object specifies the number of HDLC frames received by the ITU-C with a non-integral number of octets in the current 1-day interval. |
| 1.3.6.1.4.1.9.9.154.1.6.1.27 | ColumncIdslItucPerfCurr1DayHdlcShorts | read-only | current | This object specifies the number of short HDLC frames received by the ITU-C since agent in the current 1-day interval. A short HDLC frame contains less than 5 … |
| 1.3.6.1.4.1.9.9.154.1.6.1.28 | ColumncIdslItucPerfCurr1DayHdlcLongs | read-only | current | This object specifies the number of long HDLC frames received by the ITU-C since agent in the current 1-day interval. A long HDLC frame contains more than 1500… |
| 1.3.6.1.4.1.9.9.154.1.6.1.29 | ColumncIdslItucPerfPrev1DayMoniSecs | read-only | current | The amount of time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the int… |
| 1.3.6.1.4.1.9.9.154.1.6.1.30 | ColumncIdslItucPerfPrev1DayCVs | read-only | current | This object specifies the number of coding violations experienced by the ITU-C in the previous 1-day interval. |
| 1.3.6.1.4.1.9.9.154.1.6.1.31 | ColumncIdslItucPerfPrev1DayESs | read-only | current | This object specifies the number of errored seconds experienced by the ITU-C in the previous 1-day interval. |
| 1.3.6.1.4.1.9.9.154.1.6.1.32 | ColumncIdslItucPerfPrev1DaySESs | read-only | current | This object specifies the number of severely errored seconds experienced by the ITU-C in the previous 1-day interval. |
| 1.3.6.1.4.1.9.9.154.1.6.1.33 | ColumncIdslItucPerfPrev1DayHdlcCVs | read-only | current | This object specifies the number of HDLC coding violations experienced by the ITU-C in the previous 1-day interval. |
| 1.3.6.1.4.1.9.9.154.1.6.1.34 | ColumncIdslItucPerfPrev1DayHdlcAborts | read-only | current | This object specifies the number of HDLC aborts experienced by the ITU-C in the previous 1-day interval. |
| 1.3.6.1.4.1.9.9.154.1.6.1.35 | ColumncIdslItucPerfPrev1DayHdlcAligns | read-only | current | This object specifies the number of HDLC frames received by the ITU-C with a non-integral number of octets in the previous 1-day interval. |
| 1.3.6.1.4.1.9.9.154.1.6.1.36 | ColumncIdslItucPerfPrev1DayHdlcShorts | read-only | current | This object specifies the number of long HDLC frames received by the ITU-C since agent in the previous 1-day interval. A long HDLC frame contains more than 150… |
| 1.3.6.1.4.1.9.9.154.1.6.1.37 | ColumncIdslItucPerfPrev1DayHdlcLongs | read-only | current | This object specifies the number of long HDLC frames received by the ITU-C since agent in the previous 1-day interval. A long HDLC frame contains more than 150… |
| 1.3.6.1.4.1.9.9.154.1.7 | TablecIdslIturPerfDataTable | not-accessible | current | This table contains physical-layer statistics for ITU-R class devices supported by the system. |
| 1.3.6.1.4.1.9.9.154.1.7.1 | RowcIdslIturPerfDataEntry | not-accessible | current | A set of physical-layer statistics for an ITU-R class device supported by the system. There exists an entry for each ifEntry with an ifType of idsl(154). |
| 1.3.6.1.4.1.9.9.154.1.7.1.1 | ColumncIdslIturPerfCVs | read-only | current | This object specifies the number of coding violations experienced by the ITU-R since agent reset. |
| 1.3.6.1.4.1.9.9.154.1.7.1.2 | ColumncIdslIturPerfESs | read-only | current | This object specifies the number of errored seconds experienced by the ITU-R since agent reset. |
| 1.3.6.1.4.1.9.9.154.1.7.1.3 | ColumncIdslIturPerfSESs | read-only | current | This object specifies the number of severely errored seconds experienced by the ITU-R since agent reset. |
| 1.3.6.1.4.1.9.9.154.1.7.1.4 | ColumncIdslIturPerfValidIntervals | read-only | current | The number of previous near-end performance data 15-minute intervals for which data was collected. The value will be <n> unless the measurement was (re-)starte… |
| 1.3.6.1.4.1.9.9.154.1.7.1.5 | ColumncIdslIturPerfInvalidIntervals | read-only | current | The number of near-end performance data 15-minute intervals in the range from 0 to cSdslStucPerfValidIntervals for which no data is available. This object will… |
| 1.3.6.1.4.1.9.9.154.1.7.1.6 | ColumncIdslIturPerfCurr15MinElapsed | read-only | current | The number of seconds that have elapsed since the beginning of the current measurement period. If, for some reason, such as an adjustment in the system's time-… |
| 1.3.6.1.4.1.9.9.154.1.7.1.7 | ColumncIdslIturPerfCurr15MinCVs | read-only | current | This object specifies the number of coding violations experienced by the ITU-R in the current 15-minute interval. |
| 1.3.6.1.4.1.9.9.154.1.7.1.8 | ColumncIdslIturPerfCurr15MinESs | read-only | current | This object specifies the number of errored seconds experienced by the ITU-R in the current 15-minute interval. |
| 1.3.6.1.4.1.9.9.154.1.7.1.9 | ColumncIdslIturPerfCurr15MinSESs | read-only | current | This object specifies the number of severely errored seconds experienced by the ITU-R in the current 15-minute interval. |
| 1.3.6.1.4.1.9.9.154.1.7.1.10 | ColumncIdslIturPerfCurr1DayElapsed | read-only | current | The number of seconds that have elapsed since the beginning of the current measurement period. If, for some reason, such as an adjustment in the system's time-… |
| 1.3.6.1.4.1.9.9.154.1.7.1.11 | ColumncIdslIturPerfCurr1DayCVs | read-only | current | This object specifies the number of coding violations experienced by the ITU-R in the current 1-day interval. |
| 1.3.6.1.4.1.9.9.154.1.7.1.12 | ColumncIdslIturPerfCurr1DayESs | read-only | current | This object specifies the number of errored seconds experienced by the ITU-R in the current 1-day interval. |
| 1.3.6.1.4.1.9.9.154.1.7.1.13 | ColumncIdslIturPerfCurr1DaySESs | read-only | current | This object specifies the number of severely errored seconds experienced by the ITU-R in the current 1-day interval. |
| 1.3.6.1.4.1.9.9.154.1.7.1.14 | ColumncIdslIturPerfPrev1DayMoniSecs | read-only | current | The amount of time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the int… |
| 1.3.6.1.4.1.9.9.154.1.7.1.15 | ColumncIdslIturPerfPrev1DayCVs | read-only | current | This object specifies the number of coding violations experienced by the ITU-R in the previous 1-day interval. |
| 1.3.6.1.4.1.9.9.154.1.7.1.16 | ColumncIdslIturPerfPrev1DayESs | read-only | current | This object specifies the number of errored seconds experienced by the ITU-R in the previous 1-day interval. |
| 1.3.6.1.4.1.9.9.154.1.7.1.17 | ColumncIdslIturPerfPrev1DaySESs | read-only | current | This object specifies the number of severely errored seconds experienced by the ITU-R in the previous 1-day interval. |
| 1.3.6.1.4.1.9.9.154.1.8 | TablecIdslItucIntervalTable | not-accessible | current | This table contains physical-layer statistics intervals for ITU-C class devices supported by the system. |
| 1.3.6.1.4.1.9.9.154.1.8.1 | RowcIdslItucIntervalEntry | not-accessible | current | A 15-miute interval of physical-layer statistics for a ITU-C class device supported by the system. There exists up to 96 entries for each ifEntry with an ifTyp… |
| 1.3.6.1.4.1.9.9.154.1.8.1.1 | ColumncIdslItucIntervalNumber | read-only | current | The interval in which the statistics were collected, where the value of 1 represents the most recent interval, and the value of 96 represents the interval coll… |
| 1.3.6.1.4.1.9.9.154.1.8.1.2 | ColumncIdslItucIntervalValidData | read-only | current | This object specifies whether the data for this interval is valid. |
| 1.3.6.1.4.1.9.9.154.1.8.1.3 | ColumncIdslItucIntervalCVs | read-only | current | This object specifies the number of coding violations experienced by the ITU-C in the interval. |
| 1.3.6.1.4.1.9.9.154.1.8.1.4 | ColumncIdslItucIntervalESs | read-only | current | This object specifies the number of errored seconds experienced by the ITU-C in the interval. |
| 1.3.6.1.4.1.9.9.154.1.8.1.5 | ColumncIdslItucIntervalSESs | read-only | current | This object specifies the number of severely errored seconds experienced by the ITU-C in the interval. |
| 1.3.6.1.4.1.9.9.154.1.8.1.6 | ColumncIdslItucIntervalHdlcCVs | read-only | current | This object specifies the number of HDLC coding violations experienced by the ITU-C in the interval. |
| 1.3.6.1.4.1.9.9.154.1.8.1.7 | ColumncIdslItucIntervalHdlcAborts | read-only | current | This object specifies the number of HDLC aborts experienced by the ITU-C in the interval. |
| 1.3.6.1.4.1.9.9.154.1.8.1.8 | ColumncIdslItucIntervalHdlcAligns | read-only | current | This object specifies the number of HDLC frames received by the ITU-C with a non-integral number of octets in the interval. |
| 1.3.6.1.4.1.9.9.154.1.8.1.9 | ColumncIdslItucIntervalHdlcShorts | read-only | current | This object specifies the number of short HDLC frames received by the ITU-C since agent in the interval. A short HDLC frame contains less than 5 octets. |
| 1.3.6.1.4.1.9.9.154.1.8.1.10 | ColumncIdslItucIntervalHdlcLongs | read-only | current | This object specifies the number of long HDLC frames received by the ITU-C since agent in the interval. A long HDLC frame contains more than 1500 octets. |
| 1.3.6.1.4.1.9.9.154.1.9 | TablecIdslIturIntervalTable | not-accessible | current | This table contains physical-layer statistics intervals for ITU-R class devices supported by the system. |
| 1.3.6.1.4.1.9.9.154.1.9.1 | RowcIdslIturIntervalEntry | not-accessible | current | A 15-miute interval of physical-layer statistics for a ITU-R class device supported by the system. There exists up to 96 entries for each ifEntry with an ifTyp… |
| 1.3.6.1.4.1.9.9.154.1.9.1.1 | ColumncIdslIturIntervalNumber | read-only | current | The interval in which the statistics were collected, where the value of 1 represents the most recent interval, and the value of 96 represents the interval coll… |
| 1.3.6.1.4.1.9.9.154.1.9.1.2 | ColumncIdslIturIntervalValidData | read-only | current | This object specifies whether the data for this interval is valid. |
| 1.3.6.1.4.1.9.9.154.1.9.1.3 | ColumncIdslIturIntervalCVs | read-only | current | This object specifies the number of coding violations experienced by the ITU-R in the interval. |
| 1.3.6.1.4.1.9.9.154.1.9.1.4 | ColumncIdslIturIntervalESs | read-only | current | This object specifies the number of errored seconds experienced by the ITU-R in the interval. |
| 1.3.6.1.4.1.9.9.154.1.9.1.5 | ColumncIdslIturIntervalSESs | read-only | current | This object specifies the number of severely errored seconds experienced by the ITU-R in the interval. |
| 1.3.6.1.4.1.9.9.154.1.14 | TablecIdslLineConfProfileTable | not-accessible | current | This table extends the adslLineConfProfileTable and contains IDSL line configuration information. |
| 1.3.6.1.4.1.9.9.154.1.14.1 | RowcIdslLineConfProfileEntry | not-accessible | current | A configuration profile containing enterprise-specific IDSL line configuration information. |
| 1.3.6.1.4.1.9.9.154.1.14.1.1 | ColumncIdslLineConfRate | read-create | current | This object specifies the desired line rate. |
| 1.3.6.1.4.1.9.9.154.1.14.1.2 | ColumncIdslLineConfProtocol | read-create | current | This object specifies the layer 2 protocol to be employed by the line, and more specifically the encapsulation type: - frf Specifies the frame relay layer 2 pr… |
| 1.3.6.1.4.1.9.9.154.1.14.1.3 | ColumncIdslLineConfLmiProtocol | read-create | current | This object identifies the local inband signaling protocol. |
| 1.3.6.1.4.1.9.9.154.1.14.1.4 | ColumncIdslLineConfLmiNetN392 | read-create | current | This object specifies the interval between successive status enquiry messages. |
| 1.3.6.1.4.1.9.9.154.1.14.1.5 | ColumncIdslLineConfLmiNetN393 | read-create | current | This object specifies the value of the network-side error threshold. |
| 1.3.6.1.4.1.9.9.154.1.14.1.6 | ColumncIdslLineConfLmiNetT392 | read-create | current | This object specifies the value of the network-side polling verification timer. |
| 1.3.6.1.4.1.9.9.154.1.14.1.7 | ColumncIdslLineConfUpcIntent | read-create | current | This object specifies the default UPC (Usage Parameter Control) action for connections that do not explicitly specify a UPC action. |
| 1.3.6.1.4.1.9.9.154.1.14.1.8 | ColumncIdslLineConfBcDefault | read-create | current | This object specifies the default BC (Committed Burst Size) for connections that do not explicitly specify a BC. |
| 1.3.6.1.4.1.9.9.154.1.16 | TablecIdslPppoaPerfDataTable | not-accessible | current | This table contains PPPoA statistics for those ITU-C class devices configured for PPP operation. |
| 1.3.6.1.4.1.9.9.154.1.16.1 | RowcIdslPppoaPerfDataEntry | not-accessible | current | A set of PPPoA statistics for an ITU-C class device configured for PPP operation. There exists an entry for each ifEntry that meet the following criteria: 1) T… |
| 1.3.6.1.4.1.9.9.154.1.16.1.1 | ColumncIdslPppoaPerfRTOs | read-only | current | This object specifies the number of frames that could not be completely reassembled due to a reassembly timeout before being transmitted over this PPP session … |
| 1.3.6.1.4.1.9.9.154.1.16.1.2 | ColumncIdslPppoaPerfCVs | read-only | current | This object specifies the number of reassembled frames intended for transmission over this PPP session exhibiting a coding violation since agent reset. |
| 1.3.6.1.4.1.9.9.154.1.16.1.3 | ColumncIdslPppoaPerfShorts | read-only | current | This object specifies the number of reassembled frames intended for transmission over this PPP session containing less than 5 octets since agent reset. |
| 1.3.6.1.4.1.9.9.154.1.16.1.4 | ColumncIdslPppoaPerfLongs | read-only | current | This object specifies the number of reassembled frames intended for transmission over this PPP session containing more than 1500 octets since agent reset. |
| 1.3.6.1.4.1.9.9.154.1.16.1.5 | ColumncIdslPppoaPerfDiscards | read-only | current | This object specifies the total number of frames intended for transmission over this PPP session that were discarded for any reason since agent reset. |
| 1.3.6.1.4.1.9.9.154.1.16.1.6 | ColumncIdslPppoaPerfValidIntervals | read-only | current | The number of previous near-end performance data 15-minute intervals for which data was collected. The value will be <n> unless the measurement was (re-)starte… |
| 1.3.6.1.4.1.9.9.154.1.16.1.7 | ColumncIdslPppoaPerfInvalidIntervals | read-only | current | The number of near-end performance data 15-minute intervals in the range from 0 to cSdslStucPerfValidIntervals for which no data is available. This object will… |
| 1.3.6.1.4.1.9.9.154.1.16.1.8 | ColumncIdslPppoaPerfCurr15MinElapsed | read-only | current | The number of seconds that have elapsed since the beginning of the current measurement period. If, for some reason, such as an adjustment in the system's time-… |
| 1.3.6.1.4.1.9.9.154.1.16.1.9 | ColumncIdslPppoaPerfCurr15MinRTOs | read-only | current | This object specifies the number of frames that could not be completely reassembled due to a reassembly timeout before being transmitted over this PPP session … |
| 1.3.6.1.4.1.9.9.154.1.16.1.10 | ColumncIdslPppoaPerfCurr15MinCVs | read-only | current | This object specifies the number of reassembled frames intended for transmission over this PPP session exhibiting a coding violation in the current 15-minute i… |
| 1.3.6.1.4.1.9.9.154.1.16.1.11 | ColumncIdslPppoaPerfCurr15MinShorts | read-only | current | This object specifies the number of reassembled frames intended for transmission over this PPP session containing less than 5 octets in the current 15-minute i… |
| 1.3.6.1.4.1.9.9.154.1.16.1.12 | ColumncIdslPppoaPerfCurr15MinLongs | read-only | current | This object specifies the number of reassembled frames intended for transmission over this PPP session containing more than 1500 octets in the current 15-minut… |
| 1.3.6.1.4.1.9.9.154.1.16.1.13 | ColumncIdslPppoaPerfCurr15MinDiscards | read-only | current | This object specifies the total number of frames intended for transmission over this PPP session that were discarded for any reason in the current 15-minute in… |
| 1.3.6.1.4.1.9.9.154.1.16.1.14 | ColumncIdslPppoaPerfCurr1DayElapsed | read-only | current | The number of seconds that have elapsed since the beginning of the current measurement period. If, for some reason, such as an adjustment in the system's time-… |
| 1.3.6.1.4.1.9.9.154.1.16.1.15 | ColumncIdslPppoaPerfCurr1DayRTOs | read-only | current | This object specifies the number of frames that could not be completely reassembled due to a reassembly timeout before being transmitted over this PPP session … |
| 1.3.6.1.4.1.9.9.154.1.16.1.16 | ColumncIdslPppoaPerfCurr1DayCVs | read-only | current | This object specifies the number of reassembled frames intended for transmission over this PPP session exhibiting a coding violation in the current 1-day inter… |
| 1.3.6.1.4.1.9.9.154.1.16.1.17 | ColumncIdslPppoaPerfCurr1DayShorts | read-only | current | This object specifies the number of reassembled frames intended for transmission over this PPP session containing less than 5 octets in the current 1-day inter… |
| 1.3.6.1.4.1.9.9.154.1.16.1.18 | ColumncIdslPppoaPerfCurr1DayLongs | read-only | current | This object specifies the number of reassembled frames intended for transmission over this PPP session containing more than 1500 octets in the current 1-day in… |
| 1.3.6.1.4.1.9.9.154.1.16.1.19 | ColumncIdslPppoaPerfCurr1DayDiscards | read-only | current | This object specifies the total number of frames intended for transmission over this PPP session that were discarded for any reason in the current 1-day interv… |
| 1.3.6.1.4.1.9.9.154.1.16.1.20 | ColumncIdslPppoaPerfPrev1DayMoniSecs | read-only | current | The amount of time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the int… |
| 1.3.6.1.4.1.9.9.154.1.16.1.21 | ColumncIdslPppoaPerfPrev1DayRTOs | read-only | current | This object specifies the number of frames that could not be completely reassembled due to a reassembly timeout before being transmitted over this PPP session … |
| 1.3.6.1.4.1.9.9.154.1.16.1.22 | ColumncIdslPppoaPerfPrev1DayCVs | read-only | current | This object specifies the number of reassembled frames intended for transmission over this PPP session exhibiting a coding violation in the previous 1-day inte… |
| 1.3.6.1.4.1.9.9.154.1.16.1.23 | ColumncIdslPppoaPerfPrev1DayShorts | read-only | current | This object specifies the number of reassembled frames intended for transmission over this PPP session containing less than 5 octets in the previous 1-day inte… |
| 1.3.6.1.4.1.9.9.154.1.16.1.24 | ColumncIdslPppoaPerfPrev1DayLongs | read-only | current | This object specifies the number of reassembled frames intended for transmission over this PPP session containing more than 1500 octets in the previous 1-day i… |
| 1.3.6.1.4.1.9.9.154.1.16.1.25 | ColumncIdslPppoaPerfPrev1DayDiscards | read-only | current | This object specifies the total number of frames intended for transmission over this PPP session that were discarded for any reason in the previous 1-day inter… |
| 1.3.6.1.4.1.9.9.154.1.17 | TablecIdslPppoaIntervalTable | not-accessible | current | This table contains PPPoA statistics intervals for those ITU-C class devices configured for PPP operation. |
| 1.3.6.1.4.1.9.9.154.1.17.1 | RowcIdslPppoaIntervalEntry | not-accessible | current | A 15-minute interval of PPPoA statistics intervals for a ITU-C class device configured for PPP operation. There exists up to 96 entries for each ifEntry that m… |
| 1.3.6.1.4.1.9.9.154.1.17.1.1 | ColumncIdslPppoaIntervalNumber | read-only | current | The interval in which the statistics were collected, where the value of 1 represents the most recent interval, and the value of 96 represents the interval coll… |
| 1.3.6.1.4.1.9.9.154.1.17.1.2 | ColumncIdslPppoaIntervalValidData | read-only | current | This object specifies whether the data for this interval is valid. |
| 1.3.6.1.4.1.9.9.154.1.17.1.3 | ColumncIdslPppoaIntervalRTOs | read-only | current | This object specifies the number of frames that could not be completely reassembled due to a reassembly timeout before being transmitted over this PPP session … |
| 1.3.6.1.4.1.9.9.154.1.17.1.4 | ColumncIdslPppoaIntervalCVs | read-only | current | This object specifies the number of reassembled frames intended for transmission over this PPP session exhibiting a coding violation in the interval. |
| 1.3.6.1.4.1.9.9.154.1.17.1.5 | ColumncIdslPppoaIntervalShorts | read-only | current | This object specifies the number of reassembled frames intended for transmission over this PPP session containing less than 5 octets in the interval. |
| 1.3.6.1.4.1.9.9.154.1.17.1.6 | ColumncIdslPppoaIntervalLongs | read-only | current | This object specifies the number of reassembled frames intended for transmission over this PPP session containing more than 1500 octets in the interval. |
| 1.3.6.1.4.1.9.9.154.1.17.1.7 | ColumncIdslPppoaIntervalDiscards | read-only | current | This object specifies the total number of frames intended for transmission over this PPP session that were discarded for any reason in the interval. |
| 1.3.6.1.4.1.9.9.154.1.18 | TablecIdslPppoaMapTable | not-accessible | current | This table defines the mapping between PPP sessions and ATM VC. |
| 1.3.6.1.4.1.9.9.154.1.18.1 | RowcIdslPppoaMapEntry | not-accessible | current | A mapping between a PPP session and an ATM VC. There exists an entry for each ifEntry that meet the following criteria: 1) The ifEntry has an ifType of idsl(15… |
| 1.3.6.1.4.1.9.9.154.1.18.1.1 | ColumncIdslPppoaMapIfIndex | read-only | current | The ifIndex associated with the pseudo-ATM interface onto which the IDSL interface is being mapped. |
| 1.3.6.1.4.1.9.9.154.1.18.1.2 | ColumncIdslPppoaMapVpi | read-write | current | The VPI (Virtual Path Identifier) associated with the ATM VCL onto which the PPP session is being mapped. |
| 1.3.6.1.4.1.9.9.154.1.18.1.3 | ColumncIdslPppoaMapVci | read-write | current | The VCI (Virtual Circuit Identifier) associated with the ATM VCL onto which the PPP session is being mapped. |
| 1.3.6.1.4.1.9.9.154.2 | NodeciscoIdslLineMIBNotificationsPrefix | |||
| 1.3.6.1.4.1.9.9.154.2.0 | NodeciscoIdslLineMIBNotifications | |||
| 1.3.6.1.4.1.9.9.154.3 | NodeciscoIdslLineMIBConformance | |||
| 1.3.6.1.4.1.9.9.154.3.1 | NodeciscoIdslLineMIBCompliances | |||
| 1.3.6.1.4.1.9.9.154.3.1.1 | ComplianceciscoIdslLineMIBCompliance | current | The compliance statement for entities that implement the CISCO-IDSL-LINE-MIB. Implementation of this MIB is mandatory for any platform that supports one or mor… | |
| 1.3.6.1.4.1.9.9.154.3.2 | NodeciscoIdslLineMIBGroups | |||
| 1.3.6.1.4.1.9.9.154.3.2.1 | GroupcIdslBasicGroup | current | A collection of managed objects defining the basic operation of an IDSL line. | |
| 1.3.6.1.4.1.9.9.154.3.2.2 | GroupcIdslPM15MinIntervalGroup | current | A collection of managed objects defining performance data collection capability using 15-minute intervals. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| IdslPerfCurrDayCount | Gauge32 | current | A counter associated with interval performance measurements in a current 1-day (24 hour) measurement interval. The value of this counter starts at zero at the beginning of an interval and increases when associated event… |
| IdslPerfPrevDayCount | Gauge32 | current | A counter associated with interval performance measurements during the most previous 1-day (24 hour) measurement interval. The value of this counter is equal to the current day counter at the end of its most recent inte… |
| IdslPerfTimeElapsed | Gauge32 | current | The number of seconds that have elapsed since the beginning of the current measurement period. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value… |