CISCO-ITP-GSP-MIB
272 objects
The MIB for managing Signalling Points and its associated messages transported over Signalling System No. 7 (SS7) Network via Cisco IP Transfer Point. This MIB replaces the CISCO-ITP-SP-MIB and provide support multiple instances of a signalling point within same configuration. The Cisco IP Transfer Point (ITP) is a hardware and software solution that transports SS7 traffic using IP. Each ITP node provides function similar to SS7 Signalling point. The relevant ITU documents describing this technology is the ITU Q series, including ITU Q.700: Introduction to CCITT Signalling System No. 7 and ITU Q.701 Functional description of the message transfer part (MTP) of Signalling System No. 7. This MIB models the GSP as follows: Abbreviations: AERM - Alignment Error Rate Monitor CLLI - Common-Language Location Identification DPC - Destination Point Code GSP - Gateway Signalling Point HSL - High Speed Link (ATM based) LLSC - link set control LSAC - Signalling link activity control LSDA - Signalling data link allocation LSLA - Signalling link activation LSLD - Signalling link deactivation LSLR - Signalling link restoration LSSU - Link Status Signal Unit LSTA - Signalling terminal allocation MTP - Message Transport Protocol MTP2 - Layer 2 of Message Transport Protocol MTP3 - Layer 3 of Message Transport Protocol NTT - The Japanese Nippon Telephone & Telegraph OPC - Originating Point Code PC - Point Code RTN - RouteTableName SCTP - Stream Transmission Protocol(RFC 2960) SIB - Status Indicator Busy SLT - Signalling Link Test SLTA - Signalling Link Test Acknowledgement SP - Signalling Point SS7 - System No. 7 (SS7) Network SUERM - Signal Unit Error Rate Monitor TCBC - Changeback control TCOC - Changeover control TCRC - Controlled rerouting control TFRC - Forced rerouting control TLAC - Link availability control TPRC - Signalling point restart control TRCC - Signalling route set congestion control TSFC - Signalling traffic flow control TSRC - Signalling routing control TTC - The Japanese Telecommunications Technology Committee WRR - Weighted round robin
Imported Objects
| CISCO-ITP-TC-MIB | CItpTcAclId CItpTcCLLI CItpTcDisplayPC CItpTcInstanceNumber CItpTcLinksetId CItpTcLinkSLC CItpTcLinkType CItpTcNetworkIndicator CItpTcNetworkName CItpTcPointCode CItpTcPointCodeType CItpTcQos CItpTcRouteTableName CItpTcServiceIndicator |
| CISCO-SMI | ciscoMgmt |
| IF-MIB | InterfaceIndexOrZero |
| INET-ADDRESS-MIB | InetAddress InetAddressType InetPortNumber |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Gauge32 Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | RowStatus TEXTUAL-CONVENTION TimeStamp TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.9.336 | IdentityciscoGspMIB | The MIB for managing Signalling Points and its associated messages transported over Signalling System No. 7 (SS7) Network via Cisco IP Transfer Point. This MIB… | ||
| 1.3.6.1.4.1.9.9.336.0 | NodeciscoGspMIBNotifs | |||
| 1.3.6.1.4.1.9.9.336.0.1 | NotificationciscoGspLinksetStateChange | current | The notification generated when a linkset changes to a new state. The value of cgspLinksetState indicates the new state. | |
| 1.3.6.1.4.1.9.9.336.0.2 | NotificationciscoGspLinkStateChange | current | The notification generated when a link changes to a new state. The value of cgspLinkState indicates the new state. | |
| 1.3.6.1.4.1.9.9.336.0.3 | NotificationciscoGspCongestionChange | current | The notification generated when a link changes to a new congestion level as specified by cgspLinkCongestionState object for Transmission Side congestion. | |
| 1.3.6.1.4.1.9.9.336.0.4 | NotificationciscoGspLinkRcvdUtilChange | current | The notification provide is generated when the cgspLinkUtilStateRcvd changes states. | |
| 1.3.6.1.4.1.9.9.336.0.5 | NotificationciscoGspLinkSentUtilChange | current | The notification provide is generated when the cgspLinkUtilStateSent changes states. | |
| 1.3.6.1.4.1.9.9.336.0.6 | NotificationciscoGspIsolation | current | This notification indicates the instance specified by cgspInstDisplayName and cgspInstDescription has become isolated. All linkset used to connect MTP3 node (i… | |
| 1.3.6.1.4.1.9.9.336.0.8 | NotificationciscoGspUPUReceived | current | The notification is generated when an UPU MSU is received from a remote signalling point, for a specific instance and user part for the first time in the confi… | |
| 1.3.6.1.4.1.9.9.336.0.9 | NotificationciscoGspUPUTransmitted | current | The notification is generated when an UPU MSU is transmitted to a remote signalling point, for a specific instance and user part for the first time in the conf… | |
| 1.3.6.1.4.1.9.9.336.0.10 | NotificationciscoGspRxCongestionChange | current | The notification generated when a link changes to a new congestion level as specified by cgspLinkRxCongestionstate object for Received side congestion | |
| 1.3.6.1.4.1.9.9.336.1 | NodeciscoGspMIBObjects | |||
| 1.3.6.1.4.1.9.9.336.1.1 | NodecgspScalars | |||
| 1.3.6.1.4.1.9.9.336.1.1.1 | ScalarcgspCLLICode | read-write | current | Common-Language Location Identification Codes (CLLI Codes). This object identifies the physical location of this device and can provide additional informaton o… |
| 1.3.6.1.4.1.9.9.336.1.1.2 | ScalarcgspUtilSampleInterval | read-write | current | This object specifies the time interval used to monitor the utilization of SS7 links. This object in combination with cgspUtilThreshold, cgspLinkPlanCapacitySe… |
| 1.3.6.1.4.1.9.9.336.1.1.3 | ScalarcgspUtilThreshold | read-write | current | This object specifies the threshold of usage for all SS7 links in SP. This object is used to determine when to generate the ciscoGspLinkRcvdUtilChange or cisco… |
| 1.3.6.1.4.1.9.9.336.1.1.4 | ScalarcgspUtilAbateDelta | read-write | current | This object allows the falling threshold to be lower than the rising threshold when calculating whether to generate the ciscoGspLinkRcvdUtilChange or ciscoGspL… |
| 1.3.6.1.4.1.9.9.336.1.1.5 | ScalarcgspPlanCapacityDefault | read-write | current | This object provides a default for value for links with a cgspLinkType='sctpIp'. For all other types of linkset this value is ignored. When a linkset based on … |
| 1.3.6.1.4.1.9.9.336.1.1.6 | ScalarcgspEventSequenceNumber | read-only | current | Each event or notification is required to provide a sequence number to be used by the NMS to determine when messages from a particular device are missing. This… |
| 1.3.6.1.4.1.9.9.336.1.1.7 | ScalarcgspUPUNotifWindowTime | read-write | current | This object specifies the time interval used to monitor the ciscoGspUPUReceived and ciscoGspUPUTransmitted notifications for specific user part and signalling … |
| 1.3.6.1.4.1.9.9.336.1.2 | NodecgspProfile | |||
| 1.3.6.1.4.1.9.9.336.1.2.1 | TablecgspProfileTable | not-accessible | current | A table that contains the Profiles of signalling points. Entries are added to this table via cgspProfileRowStatus in accordance with the RowStatus convention. |
| 1.3.6.1.4.1.9.9.336.1.2.1.1 | RowcgspProfileTableEntry | not-accessible | current | A list of Profile attributes. Profiles are used to specify common configuration options for SS7 links without customizing each link. A profile is created with … |
| 1.3.6.1.4.1.9.9.336.1.2.1.1.1 | ColumncgspProfileName | not-accessible | current | Name of the profile. |
| 1.3.6.1.4.1.9.9.336.1.2.1.1.2 | ColumncgspProfileVariant | read-create | current | The SS7 variant used to format data specified in this profile. |
| 1.3.6.1.4.1.9.9.336.1.2.1.1.3 | ColumncgspProfileMtp2BundleTimer | read-create | current | Bundle timer value. This value is used to control the bundling of SS7 packets as they are transported within the device. The value of zero indicates that MTP3 … |
| 1.3.6.1.4.1.9.9.336.1.2.1.1.4 | ColumncgspProfileMtp2SendQueueDepth | read-create | current | The maximum Queue depth allowed per link for MTP2 waiting to be transmitted. |
| 1.3.6.1.4.1.9.9.336.1.2.1.1.5 | ColumncgspProfileRowStatus | read-create | current | The object is used by a management station to create or delete the row entry in cgspProfileTable following the RowStatus textual convention. |
| 1.3.6.1.4.1.9.9.336.1.2.2 | TablecgspProfileTimerTable | not-accessible | current | A table that contains a profile of timers used to configure SS7 links. Entries are added to this table via cgspProfileTimerRowStatus in accordance with the Row… |
| 1.3.6.1.4.1.9.9.336.1.2.2.1 | RowcgspProfileTimerTableEntry | not-accessible | current | A list of ProfileTimer attributes. Profiles are used to specify common timer configuration options for SS7 links without customizing each link. A profile is cr… |
| 1.3.6.1.4.1.9.9.336.1.2.2.1.1 | ColumncgspProfileTimerNumber | not-accessible | current | Index into table containing timer information. |
| 1.3.6.1.4.1.9.9.336.1.2.2.1.2 | ColumncgspProfileTimerValue | read-create | current | Value of timer selected by cgspProfileTimerNumber object. |
| 1.3.6.1.4.1.9.9.336.1.2.2.1.3 | ColumncgspProfileTimerRowStatus | read-create | current | The object is used by a management station to create or delete the row entry in cgspProfileTimerTable following the RowStatus textual convention. |
| 1.3.6.1.4.1.9.9.336.1.3 | NodecgspInstance | |||
| 1.3.6.1.4.1.9.9.336.1.3.1 | TablecgspInstanceTable | not-accessible | current | A table that contains the instances of signalling points. Entries are added to this table via cgspInstRowStatus in accordance with the RowStatus convention. |
| 1.3.6.1.4.1.9.9.336.1.3.1.1 | RowcgspInstanceTableEntry | not-accessible | current | A list of instance attributes. |
| 1.3.6.1.4.1.9.9.336.1.3.1.1.1 | ColumncgspInstNetwork | not-accessible | current | The network name is used to indicate the network in which this signalling point is participating. One or more instances of signalling points can exist in the s… |
| 1.3.6.1.4.1.9.9.336.1.3.1.1.2 | ColumncgspInstNetworkIndicator | read-create | current | The Network Indicator for this Signalling point instance. |
| 1.3.6.1.4.1.9.9.336.1.3.1.1.3 | ColumncgspInstVariant | read-create | current | The SS7 variant used to format data used by this instance. |
| 1.3.6.1.4.1.9.9.336.1.3.1.1.4 | ColumncgspInstDisplayName | read-create | current | A short identifier for the Signalling point. This value can be set by system administrator or defaults to the local point code formatted as an ASCII string. |
| 1.3.6.1.4.1.9.9.336.1.3.1.1.5 | ColumncgspInstDescription | read-create | current | A textual description for the Signalling point. |
| 1.3.6.1.4.1.9.9.336.1.3.1.1.6 | ColumncgspInstTFR | read-create | current | Allow transfer restricted messages. 'true' TFR are allowed. 'false' TFR are disabled. |
| 1.3.6.1.4.1.9.9.336.1.3.1.1.7 | ColumncgspInstCongestionsLevels | read-create | current | Allow multiple congestion levels. 'true' multiple congestion levels are allowed. 'false' multiple congestion levels are disabled. |
| 1.3.6.1.4.1.9.9.336.1.3.1.1.8 | ColumncgspInstFastRestart | read-create | current | The support for fast restarts as follows. 'true' fast restart is enabled. 'false' fast restart is disabled. |
| 1.3.6.1.4.1.9.9.336.1.3.1.1.9 | ColumncgspInstDistSccpUnseq | read-create | current | Evenly distribute Class 0 SCCP messages as follows. 'true' Evenly distribute 0 SCCP messages is enabled. 'false' Evenly distribute 0 SCCP messages is disabled. |
| 1.3.6.1.4.1.9.9.336.1.3.1.1.10 | ColumncgspInstSummaryRoutingException | read-create | current | This object is used to control the usage of the summary route when both a summary route (or ANSI cluster route) and a full point-code route (within that summar… |
| 1.3.6.1.4.1.9.9.336.1.3.1.1.11 | ColumncgspInstNumber | read-only | current | A unique Identifier assigned to each instance. |
| 1.3.6.1.4.1.9.9.336.1.3.1.1.12 | ColumncgspInstRouteTableName | read-create | current | The routing table for Signalling network management messages. |
| 1.3.6.1.4.1.9.9.336.1.3.1.1.13 | ColumncgspInstRowStatus | read-create | current | The object is used by a management station to create or delete the row entry in cgspInstanceTable following the RowStatus textual convention. |
| 1.3.6.1.4.1.9.9.336.1.3.1.1.14 | ColumncgspInstSccpWrrOpcShift | read-create | current | This object indicates the shift amount for the OPC bits in SCCP class1 WRR(Weighted round robin). The range depends on the variant as follows. The ITU range is… |
| 1.3.6.1.4.1.9.9.336.1.3.1.1.15 | ColumncgspInstSccpWrrOption | read-create | current | This object indicate the options for calculate SCCP class 1 traffic loadshare under WRR |
| 1.3.6.1.4.1.9.9.336.1.3.2 | TablecgspInstTimerTable | not-accessible | current | A table that contains the timer used to configure an instances of signalling points. Entries are added to this table via cgspInstTimerRowStatus in accordance w… |
| 1.3.6.1.4.1.9.9.336.1.3.2.1 | RowcgspInstTimerTableEntry | not-accessible | current | This table is used to configure all MTP3 timer values that apply to linksets and links. The values apply to all linkset and links defined to this signalling po… |
| 1.3.6.1.4.1.9.9.336.1.3.2.1.1 | ColumncgspInstTimerNumber | not-accessible | current | Index into table containing timer information. |
| 1.3.6.1.4.1.9.9.336.1.3.2.1.2 | ColumncgspInstTimerValue | read-create | current | Value of timer selected by cgspInstTimerNumber object. |
| 1.3.6.1.4.1.9.9.336.1.3.2.1.3 | ColumncgspInstTimerRowStatus | read-create | current | The object is used by a management station to create or delete the row entry in cgspInstTimerTable following the RowStatus textual convention. |
| 1.3.6.1.4.1.9.9.336.1.3.3 | TablecgspInstUPUTable | not-accessible | current | The Instance UPU table contains information about the number of UPU MSUs transmitted and received for the specific user part(represented by service indicator) … |
| 1.3.6.1.4.1.9.9.336.1.3.3.1 | RowcgspInstUPUTableEntry | not-accessible | current | Each table entry represent the UPU MSU statistics for a specific user part and signalling point instance. |
| 1.3.6.1.4.1.9.9.336.1.3.3.1.1 | ColumncgspMtp3SI | not-accessible | current | The service indicator. |
| 1.3.6.1.4.1.9.9.336.1.3.3.1.2 | ColumncgspInstSIUPUReceived | read-only | current | The number of UPU MSUs that were received for the associated user part(service indicator) and and signalling point instance Q752/5.7. |
| 1.3.6.1.4.1.9.9.336.1.3.3.1.3 | ColumncgspInstSIUPUTransmitted | read-only | current | The number of UPU MSUs that were transmitted for the associated user part(service indicator) and and signalling point instance. |
| 1.3.6.1.4.1.9.9.336.1.3.3.1.4 | ColumncgspInstUserPartDisplay | read-only | current | The associated instance name and user part information formatted for display. |
| 1.3.6.1.4.1.9.9.336.1.4 | NodecgspPointCode | |||
| 1.3.6.1.4.1.9.9.336.1.4.1 | TablecgspPointCodeTable | not-accessible | current | A table that contains a list of point code defined for the Signalling point defined by this instance. Entries are added to this table via cgspPointCodeRowStatu… |
| 1.3.6.1.4.1.9.9.336.1.4.1.1 | RowcgspPointCodeTableEntry | not-accessible | current | A list of Point codes for a signalling point defined by an instance. |
| 1.3.6.1.4.1.9.9.336.1.4.1.1.1 | ColumncgspPointCodeNi | not-accessible | current | The network Indicator for this pointcode. |
| 1.3.6.1.4.1.9.9.336.1.4.1.1.2 | ColumncgspPointCodeBin | not-accessible | current | The point code for this Signalling Point. |
| 1.3.6.1.4.1.9.9.336.1.4.1.1.3 | ColumncgspPointCodeType | read-create | current | The function of this point code. |
| 1.3.6.1.4.1.9.9.336.1.4.1.1.4 | ColumncgspPointCodeDisplay | read-only | current | The point code for this Signalling Point. |
| 1.3.6.1.4.1.9.9.336.1.4.1.1.5 | ColumncgspPointCodeRowStatus | read-create | current | The object is used by a management station to create or delete the row entry in cgspPointCodeTable following the RowStatus textual convention. |
| 1.3.6.1.4.1.9.9.336.1.5 | NodecgspLinkset | |||
| 1.3.6.1.4.1.9.9.336.1.5.1 | TablecgspLinksetTable | not-accessible | current | A table of linksets for this Signalling Point defined by this instance. |
| 1.3.6.1.4.1.9.9.336.1.5.1.1 | RowcgspLinksetTableEntry | not-accessible | current | A list of Signalling Point linkset attributes for Signalling Point define by this instance. |
| 1.3.6.1.4.1.9.9.336.1.5.1.1.1 | ColumncgspLinksetName | not-accessible | current | The name of the linkset. |
| 1.3.6.1.4.1.9.9.336.1.5.1.1.2 | ColumncgspLinksetSourcePointCode | read-create | current | The point code to which this linkset is connected. |
| 1.3.6.1.4.1.9.9.336.1.5.1.1.3 | ColumncgspLinksetSourceDisplayPC | read-only | current | The point code to which this linkset is connected. |
| 1.3.6.1.4.1.9.9.336.1.5.1.1.4 | ColumncgspLinksetAdjacentPointCode | read-create | current | The point code to which this linkset is connected. |
| 1.3.6.1.4.1.9.9.336.1.5.1.1.5 | ColumncgspLinksetAdjacentDisplayPC | read-only | current | The point code to which this linkset is connected. |
| 1.3.6.1.4.1.9.9.336.1.5.1.1.6 | ColumncgspLinksetState | read-only | current | The list of possible linkset states. 'available' : Traffic may flow over this linkset 'shutdown' : This linkset has been forced to an unavailable state by an a… |
| 1.3.6.1.4.1.9.9.336.1.5.1.1.7 | ColumncgspLinksetInboundAcl | read-create | current | Packets are filtered against this access control list before they are passed to the routing function. A value of zero indicates that no access control list is … |
| 1.3.6.1.4.1.9.9.336.1.5.1.1.8 | ColumncgspLinksetOutboundAcl | read-create | current | Packets are filtered against this access control list after they have passed through the routing function. A value of zero indicates that no access control lis… |
| 1.3.6.1.4.1.9.9.336.1.5.1.1.9 | ColumncgspLinksetAccountingMtp3 | read-create | current | This indicates if accounting for this linkset is enabled. 'true' Indicates that the accounting function is enabled for this linkset and is being accumulated in… |
| 1.3.6.1.4.1.9.9.336.1.5.1.1.10 | ColumncgspLinksetAccountingGtt | read-create | current | This indicates if accounting for this linkset is enabled. 'true' Indicates that the accounting function is enabled for this linkset and is being accumulated in… |
| 1.3.6.1.4.1.9.9.336.1.5.1.1.11 | ColumncgspLinksetNumLinks | read-only | current | The number of links in this linkset. |
| 1.3.6.1.4.1.9.9.336.1.5.1.1.12 | ColumncgspLinksetDurationInService | read-only | current | Time linkset was providing service related to Q752/Table 4.2. |
| 1.3.6.1.4.1.9.9.336.1.5.1.1.13 | ColumncgspLinksetDurationOutService | read-only | current | Time linkset was Out-of-Service as required for Q752/Table 4.2. |
| 1.3.6.1.4.1.9.9.336.1.5.1.1.14 | ColumncgspLinksetActPriority | read-create | current | Defines the activation priority for linksets. The linksets with the lowest values will be activated first. If two or more linksets share the same values they w… |
| 1.3.6.1.4.1.9.9.336.1.5.1.1.15 | ColumncgspLinksetDisplayName | read-create | current | A short identifier for each linkset. This value can be set by system administrator or defaults to the linkset name. |
| 1.3.6.1.4.1.9.9.336.1.5.1.1.16 | ColumncgspLinksetDescription | read-create | current | A textual description for the Signalling point. |
| 1.3.6.1.4.1.9.9.336.1.5.1.1.17 | ColumncgspLinksetRotateSlsEnable | read-create | current | This defines whether signalling link selector(SLS) will be rotated. This option only applies to ANSI variant and will return false for all other variants. By d… |
| 1.3.6.1.4.1.9.9.336.1.5.1.1.18 | ColumncgspLinksetRotateSlsShift | read-create | current | This value used to shift the signalling link selector(SLS) when rotation is enabled. This option only applies to ANSI variant and will return 0 all other varia… |
| 1.3.6.1.4.1.9.9.336.1.5.1.1.19 | ColumncgspLinksetProfileName | read-create | current | When specified this object indicates which profile will be used to establish defaults for common configuration values like MTP2 and MTP3 timers. The null strin… |
| 1.3.6.1.4.1.9.9.336.1.5.1.1.20 | ColumncgspLinksetAdjacentInst | read-only | current | When a linkset is used to carry traffic between different instances, this object contains the network name used as an index into the cgspInstanceTable table. I… |
| 1.3.6.1.4.1.9.9.336.1.5.1.1.21 | ColumncgspLinksetRowStatus | read-create | current | The object is used by a management station to create or delete the row entry in cgspLinksetTable following the RowStatus textual convention. |
| 1.3.6.1.4.1.9.9.336.1.5.2 | TablecgspLinksetTimerTable | not-accessible | current | A table that contains the timer used to configure timer values specific to a particular linkset. Entries are added to this table via cgspLinksetTimerRowStatus … |
| 1.3.6.1.4.1.9.9.336.1.5.2.1 | RowcgspLinksetTimerTableEntry | not-accessible | current | This table is used to configure all MTP3 timer values that apply to linksets and links. The values apply to this linkset and links it c contains. |
| 1.3.6.1.4.1.9.9.336.1.5.2.1.1 | ColumncgspLinksetTimerNumber | not-accessible | current | Index into table containing timer information. |
| 1.3.6.1.4.1.9.9.336.1.5.2.1.2 | ColumncgspLinksetTimerValue | read-create | current | Value of timer selected by cgspLinksetTimerNumber object. |
| 1.3.6.1.4.1.9.9.336.1.5.2.1.3 | ColumncgspLinksetTimerRowStatus | read-create | current | The object is used by a management station to create or delete the row entry in cgspLinksetTimerTable following the RowStatus textual convention. |
| 1.3.6.1.4.1.9.9.336.1.6 | NodecgspLink | |||
| 1.3.6.1.4.1.9.9.336.1.6.1 | TablecgspLinkTable | not-accessible | current | A table of links for each Signalling Point. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1 | RowcgspLinkTableEntry | not-accessible | current | A list of signalling point link attributes. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.1 | ColumncgspLinkSlc | not-accessible | current | The Signalling Link Code for this link. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.2 | ColumncgspLinkDescription | read-create | current | A textual description for this link. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.3 | ColumncgspLinkState | read-only | current | The list of possible links states. 'available' : Traffic may flow over this linkset 'failed' : Traffic management has detected a failure that prevents activati… |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.4 | ColumncgspLinkReason | read-only | current | This object provides additional information on the source of a link failure. This object will contain the last reason that caused the link to fail. 'unknown' :… |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.5 | ColumncgspLinkType | read-create | current | The link type. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.6 | ColumncgspLinkifIndex | read-create | current | If the link type specified by cgspLinkType is serial or high speed Link, this is the ifIndex specified in IF-MIB, otherwise no significance is to be placed on … |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.7 | ColumncgspLinkSctpAssociation | read-only | deprecated | Association Identifiers can be greater than 65,535. This object has been replaced by cgspLinkSctpAssociationId. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.8 | ColumncgspLinkXmitQueueDepth | read-only | current | Number of packets waiting to be sent over this link. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.9 | ColumncgspLinkXmitQueueDepthHigh | read-create | current | This is the maximum number of packets waiting to be sent over this link since the last time this value was reset as indicated by cgspLinkXmitQueueDepthHighRT. … |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.10 | ColumncgspLinkXmitQueueDepthHighRT | read-only | current | This indicates when cgspLinkXmitQueueDepthHigh was last set to 0. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.11 | ColumncgspLinkCongestionState | read-only | current | The Signalling link congestion status of this link. 0 is the least congestion level, 3 is the highest congestion level. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.12 | ColumncgspLinkCongestionAbate1 | read-create | current | Threshold used to abate congestion level 1. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.13 | ColumncgspLinkCongestionAbate2 | read-create | current | Threshold used to abate congestion level 2. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.14 | ColumncgspLinkCongestionAbate3 | read-create | current | Threshold used to abate congestion level 3. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.15 | ColumncgspLinkCongestionOnset1 | read-create | current | Threshold used to mark onset of congestion level 1. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.16 | ColumncgspLinkCongestionOnset2 | read-create | current | Threshold used to mark onset of congestion level 2. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.17 | ColumncgspLinkCongestionOnset3 | read-create | current | Threshold used to mark onset of congestion level 3. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.18 | ColumncgspLinkSigLinkTest | read-create | current | Indicated if Signalling link test is enabled on this link. true : Signalling link test is enabled. false : Signalling link test not enabled. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.19 | ColumncgspLinkQ752T1E1 | read-only | current | Duration of link in the In-Service state Q752/1.1. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.20 | ColumncgspLinkQ752T1E2 | read-only | current | Count of Signalling Link failures - All reasons Q752/1.2. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.21 | ColumncgspLinkQ752T1E3 | read-only | current | Count of Signalling Link failures - Abnormal FIBR/BSNR Q752/1.3 |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.22 | ColumncgspLinkQ752T1E5 | read-only | current | Count of Signalling Link failures - Excessive error rate Q752/1.5. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.23 | ColumncgspLinkQ752T1E7 | read-only | current | Count of alignment or proving errors Q752/1.7. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.24 | ColumncgspLinkQ752T1E8 | read-only | current | Count of signal units received in error Q752/1.8. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.25 | ColumncgspLinkQ752T1E9 | read-only | current | Count of negative acknowledgements received Q752/1.9. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.26 | ColumncgspLinkQ752T1E10 | read-only | current | Count of 'local automatic changeover' events Q752/1.10. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.27 | ColumncgspLinkQ752T1E11 | read-only | current | Count of 'local automatic changeback' events Q752/1.11. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.28 | ColumncgspLinkQ752T2E1 | read-only | current | Duration of Signalling Link unavailable(for any reason) Q752/2.1. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.29 | ColumncgspLinkQ752T2E5 | read-only | current | Duration of Signalling Link unavailable due to local management actions Q752/2.5. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.30 | ColumncgspLinkQ752T2E6 | read-only | current | Duration of Signalling Link unavailable due to remote management actions Q752/2.6. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.31 | ColumncgspLinkQ752T2E7 | read-only | current | Duration of Signalling Link unavailable due to link failure Q752/2.7. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.32 | ColumncgspLinkQ752T2E9 | read-only | current | Duration of Signalling Link unavailable due to remote processor outage Q752/2.9. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.33 | ColumncgspLinkQ752T2E10 | read-only | current | Count of 'remote processor outage' events Q752/2.10 and Q752/2.11. The standard only requires that events are issued. The entries have been combined into a sin… |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.34 | ColumncgspLinkQ752T2E15 | read-only | current | Count of Status Indicator Busy received Q752/2.15. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.35 | ColumncgspLinkQ752T2E16 | read-only | current | Count of local inhibition Q752/2.16 and Q752/2.17. The standard only requires that events are issued. The entries have been combined into a single entry to tra… |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.36 | ColumncgspLinkQ752T2E18 | read-only | current | Count of remote inhibition Q752/2.18 and Q752/2.19. The standard only requires that events are issued. The entries have been combined into a single entry to tr… |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.37 | ColumncgspLinkQ752T3E1 | read-only | current | The number of MTP3 bytes sent by this link. This measurement is specified in Q752/3.1 |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.38 | ColumncgspLinkQ752T3E2Bytes | read-only | current | The number of MTP3 bytes retransmitted on this link. This measurement is specified in Q752/3.2 |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.39 | ColumncgspLinkQ752T3E2Packets | read-only | current | The number of MTP3 packets retransmitted on this link. This measurement is specified in Q752/3.2 |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.40 | ColumncgspLinkQ752T3E3 | read-only | current | The number of MTP3 packets sent by this link. This measurement is specified in Q752/3.3. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.41 | ColumncgspLinkQ752T3E4 | read-only | current | The number of MTP3 bytes received by this link. This measurement is specified in Q752/3.4 |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.42 | ColumncgspLinkQ752T3E5 | read-only | current | The number of MTP3 packets received by this link. This measurement is specified in Q752/3.5 |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.43 | ColumncgspLinkQ752T3E6 | read-only | current | The number times this Signalling link was marked congested. This measurement is specified in Q752/3.6 |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.44 | ColumncgspLinkQ752T3E7 | read-only | current | Cumulative duration of Signalling link congestion Q752/3.7. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.45 | ColumncgspLinkQ752T3E10L1 | read-only | current | The number of packets(MSUs) discarded due to Signalling link level 1 congestion Q752/3.10 |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.46 | ColumncgspLinkQ752T3E10L2 | read-only | current | The number of packets(MSUs) discard due to Signalling link level 2 congestion Q752/3.10 |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.47 | ColumncgspLinkQ752T3E10L3 | read-only | current | The number of packets(MSUs) discard due to Signalling link level 3 congestion Q752/3.10 |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.48 | ColumncgspLinkQ752T3E11L1 | read-only | current | The number times this Signalling link entered congestion level 1 and packets were discarded. This measurement is specified in Q752/3.11 |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.49 | ColumncgspLinkQ752T3E11L2 | read-only | current | The number times this Signalling link entered congestion level 2 and packets were discarded. This measurement is specified in Q752/3.11 |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.50 | ColumncgspLinkQ752T3E11L3 | read-only | current | The number times this Signalling link entered congestion level 3 and packets were discarded. This measurement is specified in Q752/3.11 |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.51 | ColumncgspLinkLocalPeerPort | read-create | current | When cgspLinkType is set to 'sctpIp' then this object contains the local port number used to create the association supporting this link. This object can be us… |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.52 | ColumncgspLinkRemotePeerPort | read-create | current | When cgspLinkType is set to 'sctpIp' then this object contains the remote port number used to create the association supporting this link. When cgspLinkType is… |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.53 | ColumncgspLinkQosClass | read-create | current | When cgspLinkType is set to 'sctpIp' then this object contains the quality of service class to be assigned to packets sent on this association. When cgspLinkTy… |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.54 | ColumncgspLinkDisplayName | read-create | current | A short identifier for each link linkset. This value can be set by system administrator or defaults to the linkset name and SLC formatted as an ASCII string. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.55 | ColumncgspLinkDroppedPkts | read-only | current | The number of packets that were dropped by this link. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.56 | ColumncgspLinkTransmittedLSSUs | read-only | current | The number of Link Status Signal Units sent on this link. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.57 | ColumncgspLinkReceivedLSSUs | read-only | current | The number of Link Status Signal Units received on this link. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.58 | ColumncgspLinkProtocolDetails | read-only | current | This object provide details on the protocol states for this link as follows. Changeback control(TCBC) 'tcbcBuffering': Changeback control is buffering data on … |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.59 | ColumncgspLinkLsacState | read-only | current | Signalling link activity control state: 'undefined' - link is an undefined state 'inactive' - A Signalling link that is not in operation. 'active' - A Signalli… |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.60 | ColumncgspLinkTsrcState | read-only | current | Signalling traffic management routing control state: 'undefined' - link is an undefined state 'idle' - traffic management is idle 'wait5' - traffic management … |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.61 | ColumncgspLinkTcocState | read-only | current | Changeover control State: 'undefined' - Link is an undefined state. 'idle' - Link is available and idle. 'wait2' - Wait for MTP2 to initialize link. 'waitForAc… |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.62 | ColumncgspLinkTcocLocalBSNT | read-only | current | The local backward sequence number to be transmitted. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.63 | ColumncgspLinkTcocRemoteBSNT | read-only | current | The remote backward sequence number to be transmitted. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.64 | ColumncgspLinkTcbcState | read-only | current | Changeback control State: 'undefined' - link is an undefined state. 'idle' - Link is available and idle. 'firstAttempt' - First attempt at changeback. 'secondA… |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.65 | ColumncgspLinkReceivedSIBs | read-only | current | The number of status indicator 'busy' link status signal units received on this link. The SIB indicates that level two is congested at the transmitting Signall… |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.66 | ColumncgspLinkTransmittedSIBs | read-only | current | The number of status indicator 'busy' link status signal units transmitted on this link. The SIB indicates that level two is congested at the transmitting Sign… |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.67 | ColumncgspLinkMtp2T01Counts | read-only | current | The number of times the alignment ready timer has expired on this link. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.68 | ColumncgspLinkMtp2T02Counts | read-only | current | The number of times the not alignment ready timer has expired on this link. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.69 | ColumncgspLinkMtp2T03Counts | read-only | current | The number of times the aligned timer has expired on this link. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.70 | ColumncgspLinkMtp2T04Counts | read-only | current | The number of times the proving period timer has expired on this link. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.71 | ColumncgspLinkMtp2T05Counts | read-only | current | The number of times the sending status indicator busy timer has expired on this link. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.72 | ColumncgspLinkMtp2T06Counts | read-only | current | The number of times the remote congestion timer has expired on this link(Q752/1.6). |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.73 | ColumncgspLinkMtp2T07Counts | read-only | current | The number of times the excessive delay of acknowledgement timer has expired on this link(Q752/1.4). |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.74 | ColumncgspLinkOMAERMCounts | read-only | current | The number of times the Alignment Error Rate Monitor procedure was started on this link. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.75 | ColumncgspLinkOMAERMFailCounts | read-only | current | The number of times the Alignment Error Rate Monitor procedure failed on this link. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.76 | ColumncgspLinkOMSURMCounts | read-only | current | The number of times the Signal Unit Error Rate Monitor procedure was started on this link. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.77 | ColumncgspLinkOMSURMFailCounts | read-only | current | The number of times the Signal Unit Error Rate Monitor procedure failed on this link. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.78 | ColumncgspLinkPlanCapacityRcvd | read-create | current | An estimate of the number of bits per second that is expected to be received from this link. This object will be used in combination with cgspUtilSampleInterva… |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.79 | ColumncgspLinkUtilThresholdRcvd | read-create | current | This object specifies the threshold used to to generate the ciscoGspLinkRcvdUtilChange notification. The value of zero indicates the threshold has not been def… |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.80 | ColumncgspLinkUtilizationRcvd | read-only | current | An estimate of the utilization of this link for traffic received on this link in the prior time period defined by the cgspUtilSampleInterval object. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.81 | ColumncgspLinkUtilStateRcvd | read-only | current | Link Utilization State for inbound traffic. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.82 | ColumncgspLinkL2BytesRcvd | read-only | current | A count of the bytes received on the link including the additional bytes required by underlying protocols. This provides a transport independent mechanism for … |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.83 | ColumncgspLinkPlanCapacitySent | read-create | current | An estimate of the number of bits per second that is expected to be sent on this link. This object will be used in combination with cgspUtilSampleInterval, cgs… |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.84 | ColumncgspLinkUtilThresholdSent | read-create | current | This object specifies the threshold used to generate the ciscoGspLinkRcvdUtilChange notification. The value of zero indicates the threshold has not been define… |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.85 | ColumncgspLinkUtilizationSent | read-only | current | An estimate of the utilization of this link for traffic sent on this link in the prior time period defined by the cgspUtilSampleInterval object. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.86 | ColumncgspLinkUtilStateSent | read-only | current | Link Utilization State for out bound traffic. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.87 | ColumncgspLinkL2BytesSent | read-only | current | A count of the bytes sent on the link including the additional bytes required by underlying protocols. This provides a transport independent mechanism for coll… |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.88 | ColumncgspLinkTestResult | read-only | current | This object provides information on result from signalling link test received on this link. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.89 | ColumncgspLinkRowStatus | read-create | current | The object is used by a management station to create or delete the row entry in cgspLinkTable following the RowStatus textual convention. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.90 | ColumncgspLinkSctpAssociationId | read-only | current | If the link type specified by cgspLinkType is 'sctpIp', this is the association identifier defined in the Stream Control Transmission Protocol(SCTP) MIB. Where… |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.91 | ColumncgspLinkQ752T1E12 | read-only | current | Count of 'Signalling Link Restoration' events Q752/1.12. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.92 | ColumncgspLinkQ752T1E12Errors | read-only | current | Count of 'Signalling Link Restoration' error events related to Q752/1.12. i.e., the number of times the link restoration was attempted and the link was not rec… |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.93 | ColumncgspLinkQ752T2E11 | read-only | current | Count of 'remote processor recovery' events Q752/2.11. The standard only requires that events are issued. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.94 | ColumncgspLinkQ752T2E17 | read-only | current | Count of local uninhibition Q752/2.17. The standard only requires that events are issued. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.95 | ColumncgspLinkQ752T2E19 | read-only | current | Count of remote uninhibition Q752/2.19. The standard only requires that events are issued. |
| 1.3.6.1.4.1.9.9.336.1.6.1.1.96 | ColumncgspLinkRxCongestionState | read-only | current | The Signalling link Received Side congestion status of this link. 0 abate, 1 onset is the received side congestion level |
| 1.3.6.1.4.1.9.9.336.1.6.2 | TablecgspLinkTimerTable | not-accessible | current | A table that contains the timer used to configure timer values specific to a particular Link. Entries are added to this table via cgspLinkTimerRowStatus in acc… |
| 1.3.6.1.4.1.9.9.336.1.6.2.1 | RowcgspLinkTimerTableEntry | not-accessible | current | This table is used to configure all MTP3 timer values that apply to links. The values apply to a particular link. |
| 1.3.6.1.4.1.9.9.336.1.6.2.1.1 | ColumncgspLinkTimerNumber | not-accessible | current | Index into table containing timer information. |
| 1.3.6.1.4.1.9.9.336.1.6.2.1.2 | ColumncgspLinkTimerValue | read-create | current | Value of timer selected by cgspLinkTimerNumber object. |
| 1.3.6.1.4.1.9.9.336.1.6.2.1.3 | ColumncgspLinkTimerRowStatus | read-create | current | The object is used by a management station to create or delete the row entry in cgspLinkTimerTable following the RowStatus textual convention. |
| 1.3.6.1.4.1.9.9.336.1.6.3 | TablecgspLinkRemoteIpAddrTable | not-accessible | current | A table that contains the remote IP addresses used to configure a particular Link. Entries are added to this table via cgspLinkRemoteIpAddrRowStatus in accorda… |
| 1.3.6.1.4.1.9.9.336.1.6.3.1 | RowcgspLinkRemoteIpAddrTableEntry | not-accessible | current | A list of remote IP addresses per Link. |
| 1.3.6.1.4.1.9.9.336.1.6.3.1.1 | ColumncgspLinkRemoteIpAddrNumber | not-accessible | current | This object specifies the index for the IP addresses in the remote IP Address table |
| 1.3.6.1.4.1.9.9.336.1.6.3.1.2 | ColumncgspLinkRemoteIpAddrType | read-create | current | This object contains the type of the local IP address used to create an association. |
| 1.3.6.1.4.1.9.9.336.1.6.3.1.3 | ColumncgspLinkRemoteIpAddress | read-create | current | This object contains the remote IP address used to create the association with the partner of this association. |
| 1.3.6.1.4.1.9.9.336.1.6.3.1.4 | ColumncgspLinkRemoteIpAddrRowStatus | read-create | current | The object is used by a management station to create or delete the row entry in cgspLinkRemoteIpAddrTable following the RowStatus textual convention. |
| 1.3.6.1.4.1.9.9.336.1.6.4 | TablecgspLinkUtilTable | not-accessible | current | A table that contains a history of the cgspLinkUtilizationRcvd and cgspLinkUtilizationRcvd objects. In order to properly manage network capacity it is necessar… |
| 1.3.6.1.4.1.9.9.336.1.6.4.1 | RowcgspLinkUtilTableEntry | not-accessible | current | A collection of entries used to store a history link utilization values. Values from cgspLinkUtilizationRcvd and cgspLinkUtilizationSent objects are saved in c… |
| 1.3.6.1.4.1.9.9.336.1.6.4.1.1 | ColumncgspLinkUtilIndex | not-accessible | current | Index used to access historical link utilization information. Entry one corresponds to the most recent utilization window for the length of time specified by t… |
| 1.3.6.1.4.1.9.9.336.1.6.4.1.2 | ColumncgspLinkUtilRcvd | read-only | current | An estimate of the utilization of this link for traffic received on this link in the time period defined by the cgspUtilSampleInterval object. |
| 1.3.6.1.4.1.9.9.336.1.6.4.1.3 | ColumncgspLinkUtilSent | read-only | current | An estimate of the utilization of this link for traffic transmitted on this link in the time period defined by the cgspUtilSampleInterval object. |
| 1.3.6.1.4.1.9.9.336.1.6.4.1.4 | ColumncgspLinkUtilEndTimestamp | read-only | current | This timestamp indicates when time period ended for this sample. |
| 1.3.6.1.4.1.9.9.336.1.7 | NodecgspNotificationsEnable | |||
| 1.3.6.1.4.1.9.9.336.1.7.1 | ScalarcgspLsStateChangeNotifEnabled | read-write | current | The signalling point linkset notification truth value. 'true' Indicates that ciscoGspLinksetStateChange notification is to be generated when the state changes.… |
| 1.3.6.1.4.1.9.9.336.1.7.2 | ScalarcgspLnkStateChangeNotifEnabled | read-write | current | The signalling point link notification truth value. 'true' Indicates that ciscoGspLinkStateChange notification is to be generated when the state changes. That … |
| 1.3.6.1.4.1.9.9.336.1.7.3 | ScalarcgspCongestionNotifEnabled | read-write | current | The signalling point congestion notification truth value. 'true' Indicates that ciscoGspCongestionChange and ciscoGspRxCongestionChange notification is to be g… |
| 1.3.6.1.4.1.9.9.336.1.7.4 | ScalarcgspLinkUtilNotifEnabled | read-write | current | The signalling point link utilization notification truth value. 'true' Indicates that the notification of link utilization has been enabled. That is, the notif… |
| 1.3.6.1.4.1.9.9.336.1.7.5 | ScalarcgspIsolationNotifEnabled | read-write | current | The isolation notification truth value. 'true' Indicates that the notification of isolation has been enabled. That is, the notification generation is enabled. … |
| 1.3.6.1.4.1.9.9.336.1.7.6 | ScalarcgspUPUNotifEnabled | read-write | current | A control to enable or disable both ciscoGspUPUReceived and ciscoGspUPUTransmitted notifications as follows: 'true' Indicates that the ciscoGspUPUReceived and … |
| 1.3.6.1.4.1.9.9.336.1.8 | NodecgspNotificationsInfo | |||
| 1.3.6.1.4.1.9.9.336.1.8.1 | ScalarcgspUPUIntervalDuration | accessible-for-notify | current | Duration elapsed since the start of the cgspUPUNotifWindowTime interval. This duration value can range from 0 upto cgspUPUNotifWindowTime. For the notification… |
| 1.3.6.1.4.1.9.9.336.1.8.2 | ScalarcgspIntervalUPUs | accessible-for-notify | current | Number of UPU MSUs received or transmitted during this specific cgspUPUIntervalDuration interval. |
| 1.3.6.1.4.1.9.9.336.2 | NodeciscoGspMIBConform | |||
| 1.3.6.1.4.1.9.9.336.2.1 | NodeciscoGspMIBCompliances | |||
| 1.3.6.1.4.1.9.9.336.2.1.1 | ComplianceciscoGspMIBCompliance | read-only | deprecated | The compliance statement for entities which implement the CISCO-ITP-GSP-MIB |
| 1.3.6.1.4.1.9.9.336.2.1.2 | ComplianceciscoGspMIBComplianceRev1 | read-only | deprecated | The compliance statement for entities which implement the CISCO-ITP-GSP-MIB |
| 1.3.6.1.4.1.9.9.336.2.1.3 | ComplianceciscoGspMIBComplianceRev2 | read-only | deprecated | The compliance statement for entities which implement the CISCO-ITP-GSP-MIB |
| 1.3.6.1.4.1.9.9.336.2.1.4 | ComplianceciscoGspMIBComplianceRev3 | read-only | deprecated | The compliance statement for entities which implement the CISCO-ITP-GSP-MIB |
| 1.3.6.1.4.1.9.9.336.2.1.5 | ComplianceciscoGspMIBComplianceRev4 | read-only | deprecated | The compliance statement for entities which implement the CISCO-ITP-GSP-MIB |
| 1.3.6.1.4.1.9.9.336.2.1.6 | ComplianceciscoGspMIBComplianceRev5 | read-only | current | The compliance statement for entities which implement the CISCO-ITP-GSP-MIB |
| 1.3.6.1.4.1.9.9.336.2.2 | NodeciscoGspMIBGroups | |||
| 1.3.6.1.4.1.9.9.336.2.2.1 | GroupciscoGspScalarsGroup | current | Scalars Group for Gateway Signalling Point. | |
| 1.3.6.1.4.1.9.9.336.2.2.2 | GroupciscoGspProfileGroup | current | Profile Group for Gateway Signalling Point. | |
| 1.3.6.1.4.1.9.9.336.2.2.3 | GroupciscoGspInstanceGroup | current | Instance of Signalling Point. | |
| 1.3.6.1.4.1.9.9.336.2.2.4 | GroupciscoGspInstTimerGroup | current | Timers defined for each Instance of Signalling Point. | |
| 1.3.6.1.4.1.9.9.336.2.2.5 | GroupciscoGspPointCodeGroup | current | Pointcode defined for each Instance of Signalling Point. | |
| 1.3.6.1.4.1.9.9.336.2.2.6 | GroupciscoGspLinksetGroup | current | linkset objects . | |
| 1.3.6.1.4.1.9.9.336.2.2.7 | GroupciscoGspLinksetTimerGroup | current | Timers defined for each Linkset. | |
| 1.3.6.1.4.1.9.9.336.2.2.8 | GroupciscoGspLinkGroup | deprecated | SP link objects. | |
| 1.3.6.1.4.1.9.9.336.2.2.9 | GroupciscoGspLinkTimerGroup | current | Timers defined for each Link. | |
| 1.3.6.1.4.1.9.9.336.2.2.10 | GroupciscoGspLinkRemoteIpGroup | current | Remote IP addresses for each Link. | |
| 1.3.6.1.4.1.9.9.336.2.2.11 | GroupciscoGspLinkUtilGroup | current | Utilization history for each Link. | |
| 1.3.6.1.4.1.9.9.336.2.2.12 | GroupciscoGspNotificationsEnableGroup | current | SP enable notification objects. | |
| 1.3.6.1.4.1.9.9.336.2.2.13 | GroupciscoGspNotificationsGroup | current | SP notifications. | |
| 1.3.6.1.4.1.9.9.336.2.2.14 | GroupciscoGspLinkGroupRev1 | current | SP link objects. | |
| 1.3.6.1.4.1.9.9.336.2.2.15 | GroupciscoGspNotificationsEnableGroupSup1 | current | Isolation notification enable. | |
| 1.3.6.1.4.1.9.9.336.2.2.16 | GroupciscoGspNotificationsGroupSup1 | current | Isolation notification. | |
| 1.3.6.1.4.1.9.9.336.2.2.17 | GroupciscoGspLinkGroupSup1 | current | Additional Link statistics. | |
| 1.3.6.1.4.1.9.9.336.2.2.18 | GroupciscoGspScalarsGroupSup1 | current | Scalar Group supplements. | |
| 1.3.6.1.4.1.9.9.336.2.2.20 | GroupciscoGspInstUPUGroup | current | SS7 Destination and Service Indicator group. | |
| 1.3.6.1.4.1.9.9.336.2.2.21 | GroupciscoGspNotificationsInfoGroup | current | Notifications Info Group. | |
| 1.3.6.1.4.1.9.9.336.2.2.22 | GroupciscoGspNotificationsEnableGroupSup2 | current | UPU notifications enable. | |
| 1.3.6.1.4.1.9.9.336.2.2.23 | GroupciscoGspNotificationsGroupSup2 | current | Adjacent SP accessibility notification, UPU sent and received notifications. | |
| 1.3.6.1.4.1.9.9.336.2.2.24 | GroupciscoGspInstSccpWrrGroup | current | SCCP GTT weighted loadshare group. | |
| 1.3.6.1.4.1.9.9.336.2.2.25 | GroupciscoGspLinkTableEntryGroupSup1 | current | cgspLinkRxCongestionstate object for Received side congestion | |
| 1.3.6.1.4.1.9.9.336.2.2.26 | GroupciscoGspNotificationsGroupSup3 | current | Link Receive side congestion notication. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| CgspDisplayInstanceUserPart | OCTET STRING (SIZE (0..40)) | current | The instance name and user part information formatted for display. If instance name is not configured, the default local point code in ASCII string format will be provided as instance name. |
| CgspLinkCapacity | Unsigned32 (0..0 | 56000..2147483647) | current | This textual convention defines the planned capacity of a SS7 link in bit per second. When the cgspLinkType object is 'sctpIp' or 'hsl' the link capacity can be obtained from information in the IF-MIB. When the cgspLink… |
| CgspLinkTestResults | INTEGER { noErrors(0), undefinedOpc(1), incorrectOpc(2), undefinedSlc(3), incorrectSlc(4), incorrectNi(5), badPattern(6), nonAdjacent(7), failed(8) } | current | This object provides information on result from signalling link test procedures as follows. 'noErrors' : Link test did not detect any errors. 'undefinedOpc' : A signalling link test message was received with an undefine… |
| CgspLinkUtilization | Gauge32 (0..999) | current | This textual convention defines a range of values that represent a link's utilization during an interval of time. The values expressed as a percent of link capacity. Any value over 999 will be represented as 999. For SS… |
| CgspLinkUtilizationState | INTEGER { unMonitored(0), underThreshold(1), overThreshold(2) } | current | Link Utilization State as follows: 'unMonitored' - traffic for a specified direction is not being monitored. 'underThreshold' - traffic for a specified direction on a link is below the specified threshold. 'overThreshol… |
| CgspPercentThreshold | Unsigned32 (0..100) | current | This textual convention defines the allowed values used to define a threshold. This value is specified as percentage of link utilization. A value of zero indicates that this specific threshold is to be ignored. |
| CgspProfileName | OCTET STRING (SIZE (0..19)) | current | The configured name associated with a Signalling Point Profile. An octet string specified by an administrator that must be in human-readable form. The names must conform to the allowed characters that can be specified v… |
| CgspSampleInterval | Unsigned32 (60..3600) | current | This textual convention defines the allowed values for a sample interval. This value is specified in seconds and ranges from 1 minute to 1 hour. |
| CgspSequenceNumber | Unsigned32 (0..65535) | current | This textual convention defines all of the allowed values for a sequence of integers used by the SS7 protocol to transmit and acknowledge packets. The range is specified from 0 to maximum allowed value for extended sequ… |
| CgspSS7Variant | INTEGER { unknown(0), ansi(1), itu(2), china(3), ntt(4), ttc(5) } | current | The list of SS7 variants. 'unknown' : Unknown or undefined variant. 'ANSI' : The ANSI variant of the SS7 specification. 'ITU' : The ITU variant of the SS7 specification. 'China' : The China national variant. This varian… |
| CgspTimerNumbers | INTEGER { timerMtp3T01(1), timerMtp3T02(2), timerMtp3T03(3), timerMtp3T04(4), timerMtp3T05(5), timerMtp3T06(6), timerMtp3T07(7), timerMtp3T08(8), timerMtp3T09(9), timerMtp3T10(10), timerMtp3T11(11), timerMtp3T12(12), timerMtp3T13(13), timerMtp3T14(14), timerMtp3T15(15), timerMtp3T16(16), timerMtp3T17(17), timerMtp3T18(18), timerMtp3T19(19), timerMtp3T20(20), timerMtp3T21(21), timerMtp3T22(22), timerMtp3T23(23), timerMtp3T24(24), timerMtp3T25(25), timerMtp3T26(26), timerMtp3T27(27), timerMtp3T28(28), timerMtp3T29(29), timerMtp3T30(30), timerMtp3T31(31), timerMtp3T32(32), timerMtp3T33(33), timerMtp3T34(34), timerLinkTest(35), timerLinkMessag1(36), timerLinkActRetry(37), timerMtp2T01(38), timerMtp2T02(39), timerMtp2T03(40), timerMtp2T04N(41), timerMtp2T04E(42), timerMtp2T05(43), timerMtp2T06(44), timerMtp2T07(45) } | current | Enumerated values for all timers |
| CgspTimerValue | Unsigned32 (0..0 | 1..4294967295) | current | Value of timers in milliseconds as follows. A value of zero indicates that the timer is not applicable for variant or link type. The values specified in this textual convention apply to the various timers identified in … |
| CItpTcSccpWrrOption | INTEGER { sls(0), cgpaSls(1), opcSls(2), opc(3) } | current | The possible options for calculate sccp class1 traffic loadshare when GTT application group's multiplicity mode is WRR(Weighted round robin): 'sls' : Use sls to calculate loadsharing 'cgpaSls' : Use the combination of c… |