CISCO-LWAPP-AP-MIB
449 objects
This MIB is intended to be implemented on all those devices operating as Central Controllers (CC) that terminate the Light Weight Access Point Protocol tunnel from Light-weight LWAPP Access Points. This MIB provides configuration and status information about the 802.11 Access Points that have joined the controller. The relationship between CC and the LWAPP APs can be depicted as follows: +......+ +......+ +......+ +......+ + + + + + + + + + CC + + CC + + CC + + CC + + + + + + + + + +......+ +......+ +......+ +......+ .. . . . .. . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + AP + + AP + + AP + + AP + + AP + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ . . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + MN + + MN + + MN + + MN + + MN + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ The LWAPP tunnel exists between the controller and the APs. The MNs communicate with the APs through the protocol defined by the 802.11 standard. LWAPP APs, upon bootup, discover and join one of the controllers and the controller pushes the configuration, that includes the WLAN parameters, to the LWAPP APs. The APs then encapsulate all the 802.11 frames from wireless clients inside LWAPP frames and forward the LWAPP frames to the controller. GLOSSARY Access Point ( AP ) An entity that contains an 802.11 medium access control ( MAC ) and physical layer ( PHY ) interface and provides access to the distribution services via the wireless medium for associated clients. LWAPP APs encapsulate all the 802.11 frames in LWAPP frames and sends it to the controller to which it is logically connected. Basic Service Set Identifier (BSSID) The identifier for the service set comprising of all the 802.11 stations under the control of one coordinating Access Point. This identifier happens to be the MAC address of the dot11 radio interface of the Access Point. The wireless clients that associate with the Access Point get the wired uplink through this particular dot11 interface. Central Controller ( CC ) The central entity that terminates the LWAPP protocol tunnel from the LWAPP APs. Throughout this MIB, this entity also referred to as 'controller'. Light Weight Access Point Protocol ( LWAPP ) This is a generic protocol that defines the communication between the Access Points and the Central Controller. Mobile Node ( MN ) A roaming 802.11 wireless device in a wireless network associated with an access point. Station Management (SMT) This term refers to the internal management of the 802.11 protocol operations by the AP to work cooperatively with the other APs and 802.11 devices in the network. Link Latency Latency is round trip time between AP and controller. There is a continuous heart-beat between AP and controller. AP calculates latency for each time and sends to controller. AMSDU Aggregate MAC Service Data Unit. A structure containing multiple MSDUs, transported within a single (unfragmented) or multiple (fragmented) Data MPDU. DTLS Datagram Transport Layer Security (DTLS) protocol provides communications privacy for datagram protocols. The protocol allows client/server applications to communicate in a way that is designed to prevent eavesdropping, tampering, or message forgery. WIPS Wireless Intrusion Prevention System (WIPS) is a network device that monitors the radio spectrum for the presence of unauthorized access points (intrusion detection), and can automatically take countermeasures (intrusion prevention). SE Spectrum Expert is an application software, which when connected to Spectrum Intelligent Access Point, provides detailed RF spectrum plots and data, and assist in diagnosing network problems. PPPOE Point-to-Point Protocol Over Ethernet provides a standard method to build sessions for transporting multi-protocol datagrams between point-to-point links over Ethernet. REFERENCE [1] Part 11 Wireless LAN Medium Access Control ( MAC ) and Physical Layer ( PHY ) Specifications. [2] Draft-obara-capwap-lwapp-00.txt, IETF Light Weight Access Point Protocol.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.9.513 | IdentityciscoLwappApMIB | This MIB is intended to be implemented on all those devices operating as Central Controllers (CC) that terminate the Light Weight Access Point Protocol tunnel … | ||
| 1.3.6.1.4.1.9.9.513.0 | NodeciscoLwappApMIBNotifs | |||
| 1.3.6.1.4.1.9.9.513.0.1 | NotificationciscoLwappApIfRegulatoryDomainMismatchNotif | current | This notification is generated if an AP radio's regulatory domain doesn't match the country the controller is configured for. Due to the mismatch, the AP will … | |
| 1.3.6.1.4.1.9.9.513.0.2 | NotificationciscoLwappApCrash | obsolete | This notification is generated after an AP rejoins the controller after a crash. Once the AP joins, the controller will get the crash file from the AP and send… | |
| 1.3.6.1.4.1.9.9.513.0.3 | NotificationciscoLwappApUnsupported | current | This notification is generated after an unsupported AP tries to join the controller. | |
| 1.3.6.1.4.1.9.9.513.0.4 | NotificationciscoLwappApAssociated | current | This notification is generated whenever an AP joins the controller successfully. This notification contains information about the last reboot reason and Data E… | |
| 1.3.6.1.4.1.9.9.513.0.5 | NotificationciscoLwappApPower | current | This notification is generated whenever an AP detects low power from Ethernet. | |
| 1.3.6.1.4.1.9.9.513.0.6 | NotificationciscoLwappApRogueApDetected | current | This notification is generated whenever a rogue AP is detected. | |
| 1.3.6.1.4.1.9.9.513.0.7 | NotificationciscoLwappApRogueApCleared | current | This notification is generated whenever a rogue AP was detected and then subsequently if its been removed from the network. | |
| 1.3.6.1.4.1.9.9.513.0.8 | NotificationciscoLwappApWipsNotification | current | This notification is generated whenever a controller detects a WIPS event. | |
| 1.3.6.1.4.1.9.9.513.0.9 | NotificationciscoLwappApNoDownlinkChannelNotify | current | This notification is generated when ever AP fails to find new downlink channel. | |
| 1.3.6.1.4.1.9.9.513.0.10 | NotificationciscoLwappApIfUpNotify | current | This notification is generated when AP's Interface operational status goes up. | |
| 1.3.6.1.4.1.9.9.513.0.11 | NotificationciscoLwappApIfDownNotify | current | This notification is generated when AP's Interface operational status goes down. | |
| 1.3.6.1.4.1.9.9.513.0.12 | NotificationciscoLwappApClientThresholdNotify | current | This notification is generated when the number of clients on the AP's Radio Interface exceeds the limit defined in cLRFProfileHDClientTrapThreshold. | |
| 1.3.6.1.4.1.9.9.513.0.13 | NotificationciscoLwappApUpgradeFailureNotify | current | This notification is generated when AP image upgrade failed. | |
| 1.3.6.1.4.1.9.9.513.0.14 | NotificationciscoLwappApCpuUsageHigh | current | When an AP detects its CPU usage is higher than the threshold configured in clsSysApCpuUsageThreshold, this notification is generated with cLApAlarmSet set to … | |
| 1.3.6.1.4.1.9.9.513.0.15 | NotificationciscoLwappApMemoryUsageHigh | current | When an AP detects its memory usage is higher than the threshold configured in clsSysApMemoryUsageThreshold, this notification is generated with cLApAlarmSet s… | |
| 1.3.6.1.4.1.9.9.513.0.16 | NotificationciscoLwappApMaxClientLimitNotify | current | This notification is generated when the event that max client limit reached is raised or cleared. | |
| 1.3.6.1.4.1.9.9.513.0.17 | NotificationciscoLwappApAdjChannelRogueDetected | current | This notification is generated whenever a rogue AP is detected at the Adjacent channels | |
| 1.3.6.1.4.1.9.9.513.0.18 | NotificationciscoLwappApAdjChannelRogueCleared | current | This notification is generated whenever a rogue AP is detected at the Adjacent channels and then subsequently if its been removed from the network. | |
| 1.3.6.1.4.1.9.9.513.0.19 | NotificationciscoLwappApRogueDetected | current | This notification is generated whenever a rogue AP is detected at the same channel. | |
| 1.3.6.1.4.1.9.9.513.0.20 | NotificationciscoLwappApCurrentChannelRogueDetected | current | This notification is generated whenever a rogue AP is detected at the Current channel. | |
| 1.3.6.1.4.1.9.9.513.0.21 | NotificationciscoLwappApCurrentChannelRogueCleared | current | This notification is generated whenever a rogue AP is detected at the Current channels and then subsequently if its been removed from the network. | |
| 1.3.6.1.4.1.9.9.513.0.22 | NotificationciscoLwappApMonitorModeChangeNotify | current | This notification is generated when the event that AP monitor mode changed. | |
| 1.3.6.1.4.1.9.9.513.0.23 | NotificationciscoLwappApAcTimeSyncFailureTrap | current | This notification is generated when the heartbeat between AP and Controller is lost or connection broken. | |
| 1.3.6.1.4.1.9.9.513.0.24 | NotificationciscoLwappApSsidKeyConflict | current | This notification is generated whenever 2 SSIDs on same AP have same cipher key. | |
| 1.3.6.1.4.1.9.9.513.0.25 | NotificationciscoLwappApCurrChannelChanged | current | This notification is generated when the channel is changed by automatic or customized. | |
| 1.3.6.1.4.1.9.9.513.0.26 | NotificationciscoLwappApCapwapRetransmissionQueueFullEvent | current | This notification will be sent whenever capwap retransmission queue for an AP is filled. | |
| 1.3.6.1.4.1.9.9.513.1 | NodeciscoLwappApMIBObjects | |||
| 1.3.6.1.4.1.9.9.513.1.1 | NodeciscoLwappAp | |||
| 1.3.6.1.4.1.9.9.513.1.1.1 | TablecLApTable | not-accessible | current | This table represents the information about the 802.11 LWAPP Access Points that have joined the controller. LWAPP APs exchange configuration messages with the … |
| 1.3.6.1.4.1.9.9.513.1.1.1.1 | RowcLApEntry | not-accessible | current | Each entry in this table provides information about one 802.11 LWAPP Access Point that has joined the controller. Entries are removed when the APs lose their a… |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.1 | ColumncLApSysMacAddress | not-accessible | current | This object represents the radio MAC address common to the dot11 interfaces of the AP and uniquely identifies an entry in this table. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.2 | ColumncLApIfMacAddress | read-only | current | This object represents the Ethernet MAC address of the AP. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.3 | ColumncLApMaxNumberOfDot11Slots | read-only | current | This object represents the maximum number of 802.11 radio interface slots in this AP. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.4 | ColumncLApEntPhysicalIndex | read-only | current | This object provides the index value in the entPhysicalEntry corresponding to this AP. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.5 | ColumncLApName | read-write | current | This object represents the administrative name assigned to the AP by the user. If an AP is not configured, its factory default name will be ap:<last three byte… |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.6 | ColumncLApUpTime | read-only | current | This object represents the time in hundredths of a second since the last time the AP rebooted. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.7 | ColumncLLwappUpTime | read-only | current | This object represents the time in hundredths of a second since the last time the AP joined the controller. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.8 | ColumncLLwappJoinTakenTime | read-only | current | This object represents the time taken in hundredths of a second for the AP to join the controller. This could be a significant value in Mesh environments. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.9 | ColumncLApMaxNumberOfEthernetSlots | read-only | current | This object represents the maximum number of Ethernet slots in this AP. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.10 | ColumncLApPrimaryControllerAddressType | read-write | current | This object represents the type of the primary controller's address made available through cLApPrimaryControllerAddress. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.11 | ColumncLApPrimaryControllerAddress | read-write | current | This object represents the address of the primary controller that the APs will join. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.12 | ColumncLApSecondaryControllerAddressType | read-write | current | This object represents the type of the secondary controller's address made available through cLApSecondaryControllerAddress. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.13 | ColumncLApSecondaryControllerAddress | read-write | current | This object represents the address of the secondary controller that the APs will join. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.14 | ColumncLApTertiaryControllerAddressType | read-write | current | This object represents the type of the tertiary controller's address made available through cLApTertiaryControllerAddress. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.15 | ColumncLApTertiaryControllerAddress | read-write | current | This object represents the address of the tertiary controller that the APs will join. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.16 | ColumncLApLastRebootReason | read-only | current | This object represents the reason for the last reboot of the AP. none - ap reported a reboot reason code unknown to the controller. dot11gModeChange - 11g mode… |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.18 | ColumncLApEncryptionEnable | read-write | current | This object specifies whether encyrption between controller and AP is enabled or not. Encryption can only be enabled if ESM card in controller is pluged in. A … |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.19 | ColumncLApFailoverPriority | read-write | current | This object represents the AP failover priority for an AP. If a higher priority AP wishes to join the controller, it will be given preference over a join reque… |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.20 | ColumncLApPowerStatus | read-only | current | This object represents the power status of the AP low - The AP is drawing low power from Ethernet fifteendotfour - The AP is drawing 15.4 watts from Ethernet s… |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.21 | ColumncLApTelnetEnable | read-write | current | This object specifies whether Telnet session can be established to the AP. A value of 'true' indicates an Telnet session can be established to the AP. A value … |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.22 | ColumncLApSshEnable | read-write | current | This object specifies whether SSH session can be established to the AP. A value of 'true' indicates an SSH session can be established to the AP. A value of 'fa… |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.23 | ColumncLApPreStdStateEnabled | read-write | current | This object represents whether the Pre-Standard state of the AP is enabled or disabled. A value of 'true' denotes that the Pre-Standard state of the AP is enab… |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.24 | ColumncLApPwrInjectorStateEnabled | read-write | current | This object represents whether the Power Injector state of the AP is enabled or disabled. A value of 'true' denotes that the Power Injector state of the AP is … |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.25 | ColumncLApPwrInjectorSelection | read-write | current | This object specifies the Power Injector selection value of the AP. 'unknown' - is returned if 'cLApPwrInjectorStateEnabled'is set to false. 'installed' - conf… |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.26 | ColumncLApPwrInjectorSwMacAddr | read-write | current | This object represents the Mac address of the switch port that has a power Injector and is valid only when the 'cLApPwrInjectorSelection' is in 'installed' mod… |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.27 | ColumncLApWipsEnable | read-write | deprecated | This object represents if this AP is used as WIPS AP. A value of 'true' indicates that this AP is a WIPS AP. A value of 'false' indicates that this AP is not a… |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.28 | ColumncLApMonitorModeOptimization | read-write | current | This object represents the monitor mode optimization on this device. all - All optimization is enabled tracking - Tracking is optimized wips - WIPS optimizatio… |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.29 | ColumncLApDomainName | read-write | current | This represents the domain, to which the AP belongs. This attribute can be configured only if the static IP option is turned on in the AP. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.30 | ColumncLApNameServerAddressType | read-write | current | This represents the type of the IP address of the name server, made available through cLApNameServerAddress. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.31 | ColumncLApNameServerAddress | read-write | current | This represents the IP Address of the name server. This attribute can be configured only if the static IP option is turned on in the AP. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.32 | ColumncLApAMSDUEnable | read-write | current | This object specifies the AMSDU status. A value of 'true' turns on the AMSDU. A value of 'false' turns off the AMSDU. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.33 | ColumncLApEncryptionSupported | read-write | current | This object specifies whether AP Supports DTLS encryption. A value of 'true' indicates encryption is supported. A value of 'false' indicates encryption is not … |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.34 | ColumncLApRogueDetectionEnabled | read-write | current | This object specifies whether Rogue Detection is enabled in this AP. A value of 'true' enables Rogue Detection. A value of 'false' disables Rogue Detection. Ro… |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.35 | ColumncLApTcpMss | read-write | current | This object specifies the TCP Maximum Segment Size for this AP. Permissible value are between 536 and 1363. This will also enable the TCP MSS flag for this AP.… |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.36 | ColumncLApDataEncryptionStatus | read-only | current | This object specifies the data encryption status of AP. A value of 'true' means data is encrypted between AP and WLC. A value of 'false' means data is Plain Te… |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.37 | ColumncLApNsiKey | read-only | current | This object specifies the Network Spectrum Interface Key used when the AP is in Spectrum Expert Only Monitor Mode (SOMM).This object returns a non-zero value o… |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.38 | ColumncLApAdminStatus | read-write | current | This object specifies the Admin State of the AP, A value of 'true' enables the Admin State. A value of 'false' disables the Admin State. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.39 | ColumncLApPortNumber | read-only | current | This object specifies the port number on which the AP's traffic is coming through. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.40 | ColumncLApRetransmitCount | read-write | current | This object specifies the retransmission count for the Access Point Control Packet.This value represents the number of packets retransmitted after which the Ac… |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.41 | ColumncLApRetransmitTimeout | read-write | current | This object specifies the retransmission timeout for the Access Point Control packet. This value represents the timeout for each retransmission, during the fal… |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.42 | ColumncLApVenueConfigVenueGroup | read-write | current | This object indicates the venue group for this WLAN. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.43 | ColumncLApVenueConfigVenueType | read-write | current | This object indicates the venue type within a particular venue group,for this WLAN. The Venue group-Venue Type relationship is per the following table: Venue G… |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.44 | ColumncLApVenueConfigVenueName | read-write | current | This is the venue name defined for this AP Group. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.45 | ColumncLApVenueConfigLanguage | read-write | current | This is the Language defined for this AP Group. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.46 | ColumncLApLEDState | read-write | current | This object specifies whether the LED state of this access point should be enabled or disabled. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.47 | ColumncLApTrunkVlan | read-write | current | This object specifies the trunk VLAN ID assigned to this AP's Ethernet interface. When a non-zero value is assigned for this Object, the management packets wil… |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.48 | ColumncLApTrunkVlanStatus | read-only | current | This object specifies whether the trunk VLAN ID assigned to this AP's is effective. If the AP is unable to route the management frames through the trunk vlan, … |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.49 | ColumncLApLocation | read-write | current | This object specifies the user specified location of this AP. While configuring AP, user should specify a location for the AP so that its easy to figure out fo… |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.50 | ColumncLApSubMode | read-write | current | This object specifies the sub mode of the AP. The option 'wips' applies only when the AP is in local, flexConnect or monitor mode. This 'pppoe' options apply o… |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.51 | ColumncLApAssocCount | read-only | current | This object specifies the association count for the Access Point. This counter includes both successful and failed associate attempts, but does NOT include the… |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.52 | ColumncLApAssocFailResourceCount | read-only | current | This object specifies the association failure count for the Access Point due to the resource limits, i.e. the max clients of the WLAN/Radio is reached. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.53 | ColumncLApRealTimeStatsModeEnabled | read-write | current | This object specifies whether currently stats mode is 'realtime'. There are two stats-mode, realtime and normal, that specifies the stats-timer range to be 10-… |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.54 | ColumncLApAssociatedClientCount | read-only | current | This object specifies the associated client number for the Access Point. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.55 | ColumncLApMemoryCurrentUsage | read-only | current | This object specifies the percent of current memory usage of the access point. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.56 | ColumncLApMemoryAverageUsage | read-only | current | This object specifies the percent of average memory usage of the access point. The statistics window is defined by clsSysStatisticsInterval. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.57 | ColumncLApCpuCurrentUsage | read-only | current | This object specifies the percent of current CPU usage of the access point. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.58 | ColumncLApCpuAverageUsage | read-only | current | This object specifies the percent of average CPU usage of the access point. The statistics window is defined by clsSysStatisticsInterval. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.59 | ColumncLApUpgradeFromVersion | read-only | current | This object specifies the AP image upgrade from version. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.60 | ColumncLApUpgradeToVersion | read-only | current | This object specifies the AP image upgrade to version. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.61 | ColumncLApUpgradeFailureCause | read-only | current | This object specifies the cause of the AP image upgrade failure. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.62 | ColumncLApMaxClientLimitNumberTrap | read-only | current | This object specifies the max client limit number. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.63 | ColumncLApMaxClientLimitCause | read-only | current | This object specifies the cause of the max client limit reach. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.64 | ColumncLApMaxClientLimitSet | read-only | current | This object specifies whether this event is raised or cleared. 'TRUE' indicates this event is set. 'FALSE' indicates this even is cleared. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.65 | ColumncLApFloorLabel | read-write | current | This object specifies the floor label for the Access Point. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.66 | ColumncLApConnectCount | read-only | current | This object specifies the Count of AP's that are connected to the Controller. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.67 | ColumncLApReassocSuccCount | read-only | current | This object specifies the successful re-association count for the Access Point. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.68 | ColumncLApReassocFailCount | read-only | current | This object specifies the failed re-association count for the Access Point. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.69 | ColumncLAdjChannelRogueEnabled | read-write | current | This object specifies If Rogue AP Detection and Removed Traps need to be sent. A value of true enables Adj Rogue Detection. A value of false disables Adj Rogue… |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.70 | ColumncLApAssocFailCountByRate | read-only | current | This object specifies the failed association count for the Access Point caused by rate mismatch. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.71 | ColumncLApAbnormalOfflineCount | read-only | current | This object specifies the abnormal offline count for the Access Point. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.72 | ColumncLApActiveClientCount | read-only | current | This object specifies the active client number for the Access Point. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.73 | ColumncLApAssocFailCountForRssiLow | read-only | current | This object specifies the failed association count for the Access Point caused by RSSI low. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.74 | ColumncLApSysNetId | read-write | current | This object specifies the ApSysNetId which is the numeric string to identify the system information like ApName. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.75 | ColumncLApAssocFailTimes | read-only | current | This object specifies the counts of client failed association to the Access Point. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.76 | ColumncLApAntennaBandMode | read-write | current | This object specifies the mode of Antenna band. For access points, in which this variable is not relevant, value of 'notApplicable' will be returned. In the du… |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.77 | ColumncLApHeartBeatRspAvgTime | read-only | current | This object indicates the average interval between sending the echo request and receiving the echo response in AP. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.78 | ColumncLApEchoRequestCount | read-only | current | This object indicates the Echo Request packet count sent from AP to Access Controller. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.79 | ColumncLApEchoResponseLossCount | read-only | current | This object indicates the Echo Response Loss count from Access Controller to AP. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.80 | ColumncLApModuleInserted | read-only | current | This object represents the type of the module inserted in to the AP. |
| 1.3.6.1.4.1.9.9.513.1.1.1.1.81 | ColumncLApEnableModule | read-write | current | This object specifies the status of the external module . enable(1) - enable the module, disable(0) - disables the module. |
| 1.3.6.1.4.1.9.9.513.1.1.2 | TablecLApIfSmtParamTable | not-accessible | current | This table represents the station management information in the APs that have joined the controller. Information populated through the entries of this table is… |
| 1.3.6.1.4.1.9.9.513.1.1.2.1 | RowcLApIfSmtParamEntry | not-accessible | current | An entry in this table represents the information pertaining to one particular dot11 interface of this AP used to perform the 802.11 protocol operations on the… |
| 1.3.6.1.4.1.9.9.513.1.1.2.1.1 | ColumncLApIfSmtDot11Bssid | read-only | current | This object defines the base BSSID of this AP, which is the MAC address of the radio interface of this AP. |
| 1.3.6.1.4.1.9.9.513.1.1.3 | TablecLApCountryTable | not-accessible | current | This table represents the country settings for the 802.11 LWAPP Access Points that have joined the controller. An entry is automatically added by the controlle… |
| 1.3.6.1.4.1.9.9.513.1.1.3.1 | RowcLApCountryEntry | not-accessible | current | Each entry in this table provides country setting about one 802.11 LWAPP Access Point that has joined the controller. Entries are removed when the APs lose the… |
| 1.3.6.1.4.1.9.9.513.1.1.3.1.1 | ColumncLApCountryCode | read-write | current | This attribute identifies the country in which the AP is operating. This value is the 3 letter country code. |
| 1.3.6.1.4.1.9.9.513.1.1.3.1.2 | ColumncLApCountryAllowed | read-only | current | This attribute identifies the country in which the AP is operating. This value is a list of country codes sperated by comma. |
| 1.3.6.1.4.1.9.9.513.1.1.4 | ScalarciscoLwappApIfRegulatoryDomainMismatchNotifEnabled | read-write | current | The object to control the generation of ciscoLwappApIfRegulatoryDomainMismatchNotif notification. A value of 'true' indicates that the agent generates ciscoLwa… |
| 1.3.6.1.4.1.9.9.513.1.1.5 | ScalarciscoLwappApCrashEnabled | read-write | current | The object to control the generation of ciscoLwappApCrash notification. A value of 'true' indicates that the agent generates ciscoLwappApCrash notification. A … |
| 1.3.6.1.4.1.9.9.513.1.1.6 | ScalarciscoLwappApUnsupportedEnabled | read-write | current | The object to control the generation of ciscoLwappApUnsupported notification. A value of 'true' indicates that the agent generates ciscoLwappApUnsupported noti… |
| 1.3.6.1.4.1.9.9.513.1.1.7 | ScalarciscoLwappApAssociatedEnabled | read-write | current | The object to control the generation of ciscoLwappApAssociated notification. A value of 'true' indicates that the agent generates ciscoLwappApAssociated notifi… |
| 1.3.6.1.4.1.9.9.513.1.1.8 | TablecLApCrashInfoTable | not-accessible | current | This table represents the crash file information for each AP. An entry is automatically added to this table when an Access Points crashes and reboots. Entry is… |
| 1.3.6.1.4.1.9.9.513.1.1.8.1 | RowcLApCrashInfoEntry | not-accessible | current | Each entry in this table provides crash information available for each AP. |
| 1.3.6.1.4.1.9.9.513.1.1.8.1.1 | ColumncLApCrashFileName | read-only | current | This object indicates the crash file name for a specific AP. |
| 1.3.6.1.4.1.9.9.513.1.1.8.1.2 | ColumncLApCrashFileSize | read-only | current | This object indicates the size of the crash file. |
| 1.3.6.1.4.1.9.9.513.1.1.8.1.3 | ColumncLApCrashFileTimeStamp | read-only | current | This object indicates the timestamp of the crash file. |
| 1.3.6.1.4.1.9.9.513.1.1.9 | TablecLApSysInfoTable | not-accessible | current | This table represents the system information for each AP. |
| 1.3.6.1.4.1.9.9.513.1.1.9.1 | RowcLApSysInfoEntry | not-accessible | current | Each entry in this table provides system information for each AP. |
| 1.3.6.1.4.1.9.9.513.1.1.9.1.1 | ColumncLApSysMemType | read-only | current | This object specifies the AP system memory type. |
| 1.3.6.1.4.1.9.9.513.1.1.9.1.2 | ColumncLApSysMemSize | read-only | current | This object specifies the total AP system memory size in Kbytes. |
| 1.3.6.1.4.1.9.9.513.1.1.9.1.3 | ColumncLApSysFlashSize | read-only | current | This object specifies the AP flash size in Kbytes. |
| 1.3.6.1.4.1.9.9.513.1.1.9.1.4 | ColumncLApSysCpuType | read-only | current | This object specifies the AP cpu type |
| 1.3.6.1.4.1.9.9.513.1.1.9.1.5 | ColumncLApSysFlashType | read-only | current | This object specifies the AP Flash type. |
| 1.3.6.1.4.1.9.9.513.1.1.10 | TablecLApExtTable | not-accessible | current | This table represents the system information for each AP. |
| 1.3.6.1.4.1.9.9.513.1.1.10.1 | RowcLApExtEntry | not-accessible | current | Each entry in this table provides system information for each AP. |
| 1.3.6.1.4.1.9.9.513.1.1.10.1.1 | ColumncLApLEDFlashStatus | read-write | current | This object specifies the state of the AP LED Flash. |
| 1.3.6.1.4.1.9.9.513.1.1.10.1.2 | ColumncLApLEDFlashDuration | read-write | current | This object specifies the duration for which the AP's LED should blink. This is applicable when the value of cLApFlashStatus is TRUE. Value of 0 indicates the … |
| 1.3.6.1.4.1.9.9.513.1.1.10.1.3 | ColumncLApInetAddressType | read-write | current | This object represents the type of the AP address made available through cLApInetAddress. |
| 1.3.6.1.4.1.9.9.513.1.1.10.1.4 | ColumncLApInetAddress | read-write | current | This object represents the address of the Access Point. |
| 1.3.6.1.4.1.9.9.513.1.1.10.1.5 | ColumncLApStaticIpv6AddressEnabled | read-write | current | This object when disabled implies that AP will use DHCP to get the IP address. However, if it is enabled, then user should enter the IPAddress, Netmask and Gat… |
| 1.3.6.1.4.1.9.9.513.1.1.10.1.6 | ColumncLApStaticIpv6InetAddressType | read-write | current | This object represents the type of the AP's static IPv6 address made available through cLApStaticIpv6InetAddress. |
| 1.3.6.1.4.1.9.9.513.1.1.10.1.7 | ColumncLApStaticIpv6InetAddress | read-write | current | This object represents the static IPv6 address of the Access Point. |
| 1.3.6.1.4.1.9.9.513.1.1.10.1.8 | ColumncLApStaticIpv6PrefixLength | read-write | current | This represents the prefix length of the static IP Address configured on the AP. |
| 1.3.6.1.4.1.9.9.513.1.1.10.1.9 | ColumncLApStaticIpv6GatewayInetAddressType | read-write | current | This represents the type of the gateway of static IPv6 address made available through cLApStaticIpv6GatewayInetAddress. |
| 1.3.6.1.4.1.9.9.513.1.1.10.1.10 | ColumncLApStaticIpv6GatewayInetAddress | read-write | current | This represents the IPv6 Address of the Gateway server. This attribute can be configured only if the static IP option is turned on in the AP. |
| 1.3.6.1.4.1.9.9.513.1.2 | NodeciscoLwappApIf | |||
| 1.3.6.1.4.1.9.9.513.1.2.1 | TablecLApDot11IfTable | not-accessible | current | This table represents the information about the basic functional parameters corresponding to the dot11 interfaces of the APs that have joined the controller. |
| 1.3.6.1.4.1.9.9.513.1.2.1.1 | RowcLApDot11IfEntry | not-accessible | current | An entry in this table represents the 802.11 functional parameters of the dot11 interface of an AP that has joined the controller. Entries are added when the A… |
| 1.3.6.1.4.1.9.9.513.1.2.1.1.1 | ColumncLApDot11IfSlotId | not-accessible | current | This object represents the slot ID of a dot11 interface on an AP. The slot ID for a particular dot11 interface as represented by this object ranges from 0 to c… |
| 1.3.6.1.4.1.9.9.513.1.2.1.1.2 | ColumncLApDot11IfType | read-only | current | This object represents the type of this dot11 interface. |
| 1.3.6.1.4.1.9.9.513.1.2.1.1.3 | ColumncLApDot11IfRegDomain | read-only | current | This object indicates the regulatory domain for this radio type on this AP. |
| 1.3.6.1.4.1.9.9.513.1.2.1.1.4 | ColumncLApDot11nSupport | read-only | current | This objects indicates whether 802.11n support is available on this AP. |
| 1.3.6.1.4.1.9.9.513.1.2.1.1.5 | ColumncLAp11nChannelBandwidth | read-write | deprecated | This object indicates the channel bandwidth for this AP. This applies to 802.11n networks only. This has been deprecated for cLAp11ChannelBandwidth. |
| 1.3.6.1.4.1.9.9.513.1.2.1.1.6 | ColumncLApLomEnabled | read-write | deprecated | This object indicates whether this AP is being monitored by the location server. A value of 'true' indicates that the monitoring is enabled. A value of 'false'… |
| 1.3.6.1.4.1.9.9.513.1.2.1.1.7 | ColumncLApLomFirstChannel | read-write | current | This object represents the first location channel that is being monitored. |
| 1.3.6.1.4.1.9.9.513.1.2.1.1.8 | ColumncLApLomSecondChannel | read-write | current | This object represents the second location channel that is being monitored. |
| 1.3.6.1.4.1.9.9.513.1.2.1.1.9 | ColumncLApLomThirdChannel | read-write | current | This object represents the third location channel that is being monitored. |
| 1.3.6.1.4.1.9.9.513.1.2.1.1.10 | ColumncLApLomFourthChannel | read-write | current | This object represents the fourth location channel that is being monitored. |
| 1.3.6.1.4.1.9.9.513.1.2.1.1.11 | ColumncLApExtensionChannel | read-only | deprecated | This object represents the extension channel. This is applicable when the channel bandwidth is set to 40mhz. |
| 1.3.6.1.4.1.9.9.513.1.2.1.1.12 | ColumncLApLegacyBeamForming | read-write | deprecated | This object indicates the status of legacy beam forming in this AP. This object is applicable only for 11n supported APs. For APs that does not support legacy … |
| 1.3.6.1.4.1.9.9.513.1.2.1.1.13 | ColumncLApCdpOverAirEnabled | read-write | current | This object indicates the status of Cisco Discovery Protocol(CDP) in this interface, represented by cLApDot11IfSlotId of the AP, represented by cLApSysMacAddre… |
| 1.3.6.1.4.1.9.9.513.1.2.1.1.14 | ColumncLApDot11IfAdminStatus | read-write | current | This object represents the AP's interface admin status. A value of 'true' indicates admin state as Up. A value of 'false' indicates admin state as Down. |
| 1.3.6.1.4.1.9.9.513.1.2.1.1.15 | ColumncLApDot11IfLinkChangeCount | read-only | current | This object represents the link change count of a dot11 interface on an AP. |
| 1.3.6.1.4.1.9.9.513.1.2.1.1.16 | ColumncLApDot11MaxClients | read-write | current | This object represents the max supported associated clients of a dot11 interface on an AP. |
| 1.3.6.1.4.1.9.9.513.1.2.1.1.17 | ColumncLApPromiscuousModeDwelling | read-only | current | This object represents the percentage of time for the dot11 interface of an Access Point spent in promiscuous mode dwelling. |
| 1.3.6.1.4.1.9.9.513.1.2.1.1.18 | ColumncLApDot11IfStaKeepingTime | read-only | current | This object represents the time in hundredths of a second since the last dot11 interface state changed. |
| 1.3.6.1.4.1.9.9.513.1.2.1.1.19 | ColumncLApDot11IfLinkSpeed | read-only | current | Speed of the interface in units of 1,000,000 bits per second |
| 1.3.6.1.4.1.9.9.513.1.2.1.1.20 | ColumncLApDot11IfMtu | read-only | current | This object represents interface's MTU value |
| 1.3.6.1.4.1.9.9.513.1.2.1.1.21 | ColumncLApDot11IfDesc | read-only | current | This object represents the description of this interface |
| 1.3.6.1.4.1.9.9.513.1.2.1.1.22 | ColumncLApDot11acSupport | read-only | current | This objects indicates whether 802.11ac support is available on this AP. |
| 1.3.6.1.4.1.9.9.513.1.2.1.1.23 | ColumncLAp11ChannelBandwidth | read-write | current | This object indicates the channel bandwidth for this AP. This applies to 802.11n and 802.11ac networks only. |
| 1.3.6.1.4.1.9.9.513.1.2.1.1.24 | ColumncLApExtensionChannels | read-only | current | This object represents the extension channels separated by commas. This is applicable when the channel bandwidth is set to 40mhz or 80mhz. |
| 1.3.6.1.4.1.9.9.513.1.2.1.1.25 | ColumncLAPDot11IfMinTxPowerStep | read-only | current | This object represents minimum adjust step of the AP radio TX power. The power step is coded as an unsigned integer in units of dbm. |
| 1.3.6.1.4.1.9.9.513.1.2.2 | TablecLApEthernetIfTable | not-accessible | current | This table represents the information about the basic functional parameters corresponding to the Ethernet interfaces of the APs that have joined the controller. |
| 1.3.6.1.4.1.9.9.513.1.2.2.1 | RowcLApEthernetIfEntry | not-accessible | current | An entry in this table represents the functional parameters of the Ethernet interface of an AP that has joined the controller. Entries are added when the APs a… |
| 1.3.6.1.4.1.9.9.513.1.2.2.1.1 | ColumncLApEthernetIfSlotId | not-accessible | current | This object represents the slot ID of an Ethernet interface on an AP. The slot ID for a particular Ethernet interface as represented by this object ranges from… |
| 1.3.6.1.4.1.9.9.513.1.2.2.1.2 | ColumncLApEthernetIfName | read-only | current | This object represents the name of the Ethernet interface. |
| 1.3.6.1.4.1.9.9.513.1.2.2.1.3 | ColumncLApEthernetIfMacAddress | read-only | current | This object represents MAC address of the Ethernet interface in the slot represented by cLApEthernetIfSlotId. |
| 1.3.6.1.4.1.9.9.513.1.2.2.1.4 | ColumncLApEthernetIfAdminStatus | read-write | current | This object represents the admin state of the physical Ethernet interface on the AP. |
| 1.3.6.1.4.1.9.9.513.1.2.2.1.5 | ColumncLApEthernetIfOperStatus | read-only | current | This object represents the operational state of the physical Ethernet interface on the AP. |
| 1.3.6.1.4.1.9.9.513.1.2.2.1.6 | ColumncLApEthernetIfRxUcastPkts | read-only | current | This object represents total number of unicast packets received on the interface. |
| 1.3.6.1.4.1.9.9.513.1.2.2.1.7 | ColumncLApEthernetIfRxNUcastPkts | read-only | current | This object represents total number of non-unicast or multicast packets received on the interface |
| 1.3.6.1.4.1.9.9.513.1.2.2.1.8 | ColumncLApEthernetIfTxUcastPkts | read-only | current | This object represents total number of unicast packets transmitted on the interface. |
| 1.3.6.1.4.1.9.9.513.1.2.2.1.9 | ColumncLApEthernetIfTxNUcastPkts | read-only | current | This object represents total number of non-unicast or multicast packets transmitted on the interface |
| 1.3.6.1.4.1.9.9.513.1.2.2.1.10 | ColumncLApEthernetIfDuplex | read-only | current | This object represents interface's duplex mode |
| 1.3.6.1.4.1.9.9.513.1.2.2.1.11 | ColumncLApEthernetIfLinkSpeed | read-only | current | Speed of the interface in units of 1,000,000 bits per second |
| 1.3.6.1.4.1.9.9.513.1.2.2.1.12 | ColumncLApEthernetIfPOEPower | read-only | current | This object represents whether this interface supports Power Over Ethernet (POE) none - POE is not supported drawn - This interface supports POE, and power is … |
| 1.3.6.1.4.1.9.9.513.1.2.2.1.13 | ColumncLApEthernetIfRxTotalBytes | read-only | current | This object represents total number of bytes in the error-free packets received on the interface. |
| 1.3.6.1.4.1.9.9.513.1.2.2.1.14 | ColumncLApEthernetIfTxTotalBytes | read-only | current | This object represents total number of bytes in the error-free packets transmitted on the interface. |
| 1.3.6.1.4.1.9.9.513.1.2.2.1.15 | ColumncLApEthernetIfInputCrc | read-only | current | This object represents total number of CRC error in packets received on the interface. |
| 1.3.6.1.4.1.9.9.513.1.2.2.1.16 | ColumncLApEthernetIfInputAborts | read-only | current | This object represents total number of packet aborted while receiving on the interface. |
| 1.3.6.1.4.1.9.9.513.1.2.2.1.17 | ColumncLApEthernetIfInputErrors | read-only | current | This object represents sum of all errors in the packets while receiving on the interface. |
| 1.3.6.1.4.1.9.9.513.1.2.2.1.18 | ColumncLApEthernetIfInputFrames | read-only | current | This object represents total number of packet received incorrectly having a CRC error and a noninteger number of octets on the interface. |
| 1.3.6.1.4.1.9.9.513.1.2.2.1.19 | ColumncLApEthernetIfInputOverrun | read-only | current | This object represents the number of times the receiver hardware was incapable of handing received data to a hardware buffer because the input rate exceeded th… |
| 1.3.6.1.4.1.9.9.513.1.2.2.1.20 | ColumncLApEthernetIfInputDrops | read-only | current | This object represents total number of packets dropped while receiving on the interface because the queue was full. |
| 1.3.6.1.4.1.9.9.513.1.2.2.1.21 | ColumncLApEthernetIfInputResource | read-only | current | This object represents total number of resource errors in packets received on the interface. |
| 1.3.6.1.4.1.9.9.513.1.2.2.1.22 | ColumncLApEthernetIfUnknownProtocol | read-only | current | This object represents total number of packet discarded on the interface due to unknown protocol. |
| 1.3.6.1.4.1.9.9.513.1.2.2.1.23 | ColumncLApEthernetIfRunts | read-only | current | This object represents number of packets that are discarded because they are smaller than the medium's minimum packet size. |
| 1.3.6.1.4.1.9.9.513.1.2.2.1.24 | ColumncLApEthernetIfGiants | read-only | current | This object represents number of packets that are discarded because they exceed the medium's maximum packet size. |
| 1.3.6.1.4.1.9.9.513.1.2.2.1.25 | ColumncLApEthernetIfThrottle | read-only | current | This object represents total number of times the interface advised a sending NIC that it was overwhelmed by packets being sent and to slow the pace of delivery. |
| 1.3.6.1.4.1.9.9.513.1.2.2.1.26 | ColumncLApEthernetIfResets | read-only | current | This object represents number of times that an interface has been completely reset. |
| 1.3.6.1.4.1.9.9.513.1.2.2.1.27 | ColumncLApEthernetIfOutputCollision | read-only | current | This object represents total number of packet retransmitted due to an Ethernet collision. |
| 1.3.6.1.4.1.9.9.513.1.2.2.1.28 | ColumncLApEthernetIfOutputNoBuffer | read-only | current | This object represents total number of packets discarded because there was no buffer space. |
| 1.3.6.1.4.1.9.9.513.1.2.2.1.29 | ColumncLApEthernetIfOutputResource | read-only | current | This object represents total number of resource errors in packets transmitted on the interface. |
| 1.3.6.1.4.1.9.9.513.1.2.2.1.30 | ColumncLApEthernetIfOutputUnderrun | read-only | current | This object represents the number of times the transmitter has been running faster than the router can handle. |
| 1.3.6.1.4.1.9.9.513.1.2.2.1.31 | ColumncLApEthernetIfOutputErrors | read-only | current | This object represents sum of all errors that prevented the final transmission of packets out of the interface. |
| 1.3.6.1.4.1.9.9.513.1.2.2.1.32 | ColumncLApEthernetIfOutputTotalDrops | read-only | current | This object represents total number of packets dropped while transmitting from the interface because the queue was full. |
| 1.3.6.1.4.1.9.9.513.1.2.2.1.33 | ColumncLApEthernetIfCdpEnabled | read-write | current | This object indicates the status of Cisco Discovery Protocol(CDP) in this interface represented by cLApEthernetIfSlotId of the AP represented by cLApSysMacAddr… |
| 1.3.6.1.4.1.9.9.513.1.2.2.1.34 | ColumncLApEthernetIfMtu | read-only | current | This object represents interface's MTU value |
| 1.3.6.1.4.1.9.9.513.1.2.2.1.35 | ColumncLApEthernetIfType | read-only | current | The type of interface. Additional values for ifType are assigned by the Internet Assigned Numbers Authority (IANA), through updating the syntax of the IANAifTy… |
| 1.3.6.1.4.1.9.9.513.1.2.2.1.36 | ColumncLApEthernetIfLinkChangeCount | read-only | current | This object represents the link change count of ethernet interface on the AP. |
| 1.3.6.1.4.1.9.9.513.1.2.3 | TablecLApDot11RadioTable | not-accessible | current | This table represents the information about the basic functional parameters of the radios of the APs that have joined the controller. |
| 1.3.6.1.4.1.9.9.513.1.2.3.1 | RowcLApDot11RadioEntry | not-accessible | current | An entry in this table represents the 802.11 functional parameters of the radio of an AP that has joined the controller. Entries are added when the APs associa… |
| 1.3.6.1.4.1.9.9.513.1.2.3.1.1 | ColumncLApDot11RadioMACAddress | read-only | current | This object represents the base Mac address of the radio. |
| 1.3.6.1.4.1.9.9.513.1.2.3.1.2 | ColumncLApDot11RadioSubBand | read-only | current | This object indicates the sub band on which this radio operates. |
| 1.3.6.1.4.1.9.9.513.1.2.3.1.3 | ColumncLApDot11RadioVersion | read-only | current | This attribute identifies firmware version of the radio. |
| 1.3.6.1.4.1.9.9.513.1.2.3.1.4 | ColumncLApDot11IsBackhaul | read-only | current | This object represents whether this interface is backhaul radio or not. |
| 1.3.6.1.4.1.9.9.513.1.2.3.1.5 | ColumncLApDot11RadioRole | read-only | current | This attribute identifies role of the radio. |
| 1.3.6.1.4.1.9.9.513.1.2.4 | TablecLApDot11IfAntennaTable | not-accessible | current | This table represents the information about the basic functional parameters corresponding to the antenna on dot11 interfaces of the APs that have joined the co… |
| 1.3.6.1.4.1.9.9.513.1.2.4.1 | RowcLApDot11IfAntennaEntry | not-accessible | current | An entry in this table represents the 802.11 functional parameters of the dot11 interface of an AP that has joined the controller. Entries are added when the A… |
| 1.3.6.1.4.1.9.9.513.1.2.4.1.1 | ColumncLApDot11IfAntennaId | not-accessible | current | This object represents the antenna ID of a dot11 interface on an AP. The antenna Id for a particular dot11 interface on a slot as represented by this object. |
| 1.3.6.1.4.1.9.9.513.1.2.4.1.2 | ColumncLApDot11IfAntennaTxEnable | read-write | current | This object specifies whether this antenna is allowed to trasmit or not. A value of 'true' enables the antenna to transmit. A value of 'false' disables the ant… |
| 1.3.6.1.4.1.9.9.513.1.2.4.1.3 | ColumncLApDot11IfAntennaRxEnable | read-write | current | This object specifies whether this antenna is allowed to recieve or not. A value of 'true' enables the antenna to receive. A value of 'false' disables the ante… |
| 1.3.6.1.4.1.9.9.513.1.2.4.1.4 | ColumncLApDot11IfAntennaEnable | read-write | current | This object specifies whether this antenna is enabled or not. A value of 'true' enables the antenna. A value of 'false' disables the antenna. |
| 1.3.6.1.4.1.9.9.513.1.2.5 | TablecLApVlanIfTable | not-accessible | current | This table represents the information about the basic functional parameters corresponding to the Ethernet interfaces of the APs that have joined the controller. |
| 1.3.6.1.4.1.9.9.513.1.2.5.1 | RowcLApVlanIfEntry | not-accessible | current | An entry in this table represents the VLAN functional parameters of the Ethernet interface of an AP that has joined the controller. Entries are added when the … |
| 1.3.6.1.4.1.9.9.513.1.2.5.1.1 | ColumncLApVlanIfEthernetId | not-accessible | current | This object represents the ID of a Ethernet interface on an AP. |
| 1.3.6.1.4.1.9.9.513.1.2.5.1.2 | ColumncLApVlanIfMode | read-write | current | This object represents the mode this on this AP's Ethernet interface is configured for. normal - VLAN is not operating in access or trunk. access - VLAN is ope… |
| 1.3.6.1.4.1.9.9.513.1.2.5.1.3 | ColumncLApVlanIfEnable | read-write | current | This object specifies whether this interface is enabled or not. A value of 'true' enables the interface. A value of 'false' will disable the interface. This wi… |
| 1.3.6.1.4.1.9.9.513.1.2.5.1.4 | ColumncLApVlanIfNativeVlanId | read-write | current | This object represents the native VLAN ID assigned to this AP's Ethernet interface. This only applies when the icLApVlanIfMode is set to 'trunk'. For all other… |
| 1.3.6.1.4.1.9.9.513.1.2.6 | TablecLApVlanListTable | not-accessible | current | This table represents the information about the basic functional parameters corresponding to the VLAN Ethernet interfaces of the APs that have joined the contr… |
| 1.3.6.1.4.1.9.9.513.1.2.6.1 | RowcLApVlanListEntry | not-accessible | current | An entry in this table represents the VLAN functional parameters of the Ethernet interface of an AP that has joined the controller. Entries are added when the … |
| 1.3.6.1.4.1.9.9.513.1.2.6.1.1 | ColumncLApVlanListVlanId | not-accessible | current | This object represents the ID assigned to the VLAN on this AP's Ethernet interface. |
| 1.3.6.1.4.1.9.9.513.1.2.6.1.2 | ColumncLApVlanListRowStatus | read-create | current | Used to add or delete an entry in this table. |
| 1.3.6.1.4.1.9.9.513.1.2.7 | TablecLApDot11GlobalConfigTable | not-accessible | current | This table represents the information about the global attributes of the radio interface, that would be applicable for all the APs that join the controller. |
| 1.3.6.1.4.1.9.9.513.1.2.7.1 | RowcLApDot11GlobalConfigEntry | not-accessible | current | An entry in this table represents the network level configurations of the radio interface. Entries cannot be added or deleted in this table. |
| 1.3.6.1.4.1.9.9.513.1.2.7.1.1 | ColumncLApNwLegacyBeamForming | read-write | deprecated | This object indicates the status of legacy beam forming in this AP. This object is applicable only for 11n supported APs. For APs that does not support legacy … |
| 1.3.6.1.4.1.9.9.513.1.2.7.1.2 | ColumncLApNwTxPowerThreshold | read-write | current | This object represents the Global AP Transmit Power Threshold value. The permissible range is -80 dbm to -50 dbm |
| 1.3.6.1.4.1.9.9.513.1.2.7.1.3 | ColumncLApNwTxPowerThresholdVer2 | read-write | current | This object represents the Global AP Transmit Power Threshold value when Inteference Optimal mode of Tx Power Control (TPC v2) is enabled. The permissible rang… |
| 1.3.6.1.4.1.9.9.513.1.2.8 | TablecLApDot11RadioStatsTable | not-accessible | current | This table represents the statistics information about the radios of the APs that have joined the controller. |
| 1.3.6.1.4.1.9.9.513.1.2.8.1 | RowcLApDot11RadioStatsEntry | not-accessible | current | An entry in this table represents a statistics of the radio of an AP that has joined the conttroller. Entries are added when the APs associate to this controll… |
| 1.3.6.1.4.1.9.9.513.1.2.8.1.1 | ColumncLApDot11RadioStatsRxErrorFrameCount | read-only | current | This object represents the number of error frames received on the radio. |
| 1.3.6.1.4.1.9.9.513.1.2.8.1.2 | ColumncLApDot11RadioStatsMacMicErrFrameCount | read-only | current | This object represents the number of frames with wrong MIC received by AP on the radio. |
| 1.3.6.1.4.1.9.9.513.1.2.8.1.3 | ColumncLApDot11RadioStatsMacDecryptErrFrameCount | read-only | current | This object represents the number of frames with destroyed encrypted data received by AP on the radio. |
| 1.3.6.1.4.1.9.9.513.1.2.8.1.4 | ColumncLApDot11RadioStatsRxMgmtFrameCount | read-only | current | This object represents the total number of management frame received on the radio. |
| 1.3.6.1.4.1.9.9.513.1.2.8.1.5 | ColumncLApDot11RadioStatsRxCtrlFrameCount | read-only | current | This object represents the total number of control frame received on the radio. |
| 1.3.6.1.4.1.9.9.513.1.2.8.1.6 | ColumncLApDot11RadioStatsRxDataFrameCount | read-only | current | This object represents the total number of data frame received on the radio. |
| 1.3.6.1.4.1.9.9.513.1.2.8.1.7 | ColumncLApDot11RadioStatsTxMgmtFrameCount | read-only | current | This object represents the total number of management frame transmitted on the radio. |
| 1.3.6.1.4.1.9.9.513.1.2.8.1.8 | ColumncLApDot11RadioStatsTxCtrlFrameCount | read-only | current | This object represents the total number of control frame transmitted on the radio. |
| 1.3.6.1.4.1.9.9.513.1.2.8.1.9 | ColumncLApDot11RadioStatsTxDataFrameCount | read-only | current | This object represents the total number of data frame transmitted on the radio. |
| 1.3.6.1.4.1.9.9.513.1.2.8.1.10 | ColumncLApDot11RadioStatsRxDataPacketCount | read-only | current | This object represents the total number of data packets received on the radio. |
| 1.3.6.1.4.1.9.9.513.1.2.8.1.11 | ColumncLApDot11RadioStatsTxDataPacketCount | read-only | current | This object represents the total number of data packets transmitted on the radio. |
| 1.3.6.1.4.1.9.9.513.1.2.8.1.12 | ColumncLApDot11RadioStatsRetryFrameCount | read-only | current | This object represents the total number of downstream retry frames on the radio. |
| 1.3.6.1.4.1.9.9.513.1.2.8.1.13 | ColumncLApDot11RadioStatsRetryPacketCount | read-only | current | This object represents the total number of downstream retry packets on the radio. |
| 1.3.6.1.4.1.9.9.513.1.2.9 | TablecLApDot11RadioRssiTable | not-accessible | current | This table represents Per AP, Per Radio Stats information of Average, Highest, Lowest Rssi of all the clients update of the APs Radio. |
| 1.3.6.1.4.1.9.9.513.1.2.9.1 | RowcLApDot11RadioRssiEntry | not-accessible | current | This entry contains stats information of Average, Highest and Lowest RSSI of Per AP Per Radio. |
| 1.3.6.1.4.1.9.9.513.1.2.9.1.1 | ColumncLApDot11RadioRssiHighest | read-only | current | This object represents the Highest Rssi value of the specific radio on this access point. The value '0' dbm represents no activity on this access point radio. |
| 1.3.6.1.4.1.9.9.513.1.2.9.1.2 | ColumncLApDot11RadioRssiLowest | read-only | current | This object represents the Lowest Rssi value of the specific radio on this access point. The value '0' dbm represents no activity on this access point radio. |
| 1.3.6.1.4.1.9.9.513.1.2.9.1.3 | ColumncLApDot11RadioRssiAverage | read-only | current | This object represents the Average Rssi value of the specific radio on this access point. The value '0' dbm represents no activity on this access point radio. |
| 1.3.6.1.4.1.9.9.513.1.2.10 | TablecLApDot11RadioRateStatsTable | not-accessible | current | This table represents per AP, per radio, per rate stats information of all the clients of the APs Radio. |
| 1.3.6.1.4.1.9.9.513.1.2.10.1 | RowcLApDot11RadioRateStatsEntry | not-accessible | current | This entry contains stats information of Rx/Tx packets and bytes of per AP per radio per rate. |
| 1.3.6.1.4.1.9.9.513.1.2.10.1.1 | ColumncLApDot11RadioRate | not-accessible | current | This object uniquely identifies the data rate value for a particular band. |
| 1.3.6.1.4.1.9.9.513.1.2.10.1.2 | ColumncLApDot11RadioRateStatsRxPackets | read-only | current | This object represents the number of packets received for the specific radio and data rate on this access point. |
| 1.3.6.1.4.1.9.9.513.1.2.10.1.3 | ColumncLApDot11RadioRateStatsRxBytes | read-only | current | This object represents the number of bytes received for the specific radio and data rate on this access point. |
| 1.3.6.1.4.1.9.9.513.1.2.10.1.4 | ColumncLApDot11RadioRateStatsTxPackets | read-only | current | This object represents the number of packets transmitted from the specific radio and data rate on this access point. |
| 1.3.6.1.4.1.9.9.513.1.2.10.1.5 | ColumncLApDot11RadioRateStatsTxBytes | read-only | current | This object represents the number of bytes transmitted from the specific radio and data rate on this access point. |
| 1.3.6.1.4.1.9.9.513.1.2.10.1.6 | ColumncLApDot11RadioRateString | read-only | current | This object represents the data rate in a user-friendly text string format. |
| 1.3.6.1.4.1.9.9.513.1.2.11 | TablecLApDot11RadioSsidTable | not-accessible | current | This table represents Per AP, Per Radio information of Ssid of all the neighbor APs updating the APs Radio. |
| 1.3.6.1.4.1.9.9.513.1.2.11.1 | RowcLApDot11RadioSsidEntry | not-accessible | current | This entry contains ssid information of Neighbor APs of Per AP Per Radio. |
| 1.3.6.1.4.1.9.9.513.1.2.11.1.1 | ColumncLApSsidIndex | not-accessible | current | This object indicates the index of the ssid detected by Per AP Per Radio. |
| 1.3.6.1.4.1.9.9.513.1.2.11.1.2 | ColumncLApDot11RadioSsidName | read-only | current | This object represents the ssid name of the neighbor AP on this access point. |
| 1.3.6.1.4.1.9.9.513.1.3 | NodeciscoLwappApGlobal | |||
| 1.3.6.1.4.1.9.9.513.1.3.1 | TablecLApFastHbTimerTable | not-accessible | current | This table contains entries for AP fast heartbeat timers configured in the controller. At startup, all the entries in this table are set up by the central cont… |
| 1.3.6.1.4.1.9.9.513.1.3.1.1 | RowcLApFastHbTimerEntry | not-accessible | current | A conceptual row in cLApFastHbTimerTable. There is an entry in this table for each AP type, as identified by a value of cLApFastHbTimerApType. |
| 1.3.6.1.4.1.9.9.513.1.3.1.1.1 | ColumncLApFastHbTimerApType | not-accessible | current | This object represents the AP type for this entry. local - indicates that timer is for local mode APs hreap - indicates that timer is for HREAP APs |
| 1.3.6.1.4.1.9.9.513.1.3.1.1.2 | ColumncLApFastHbTimerTimeout | read-write | current | This object represents the timeout value for the heart beat timer. This value changes to 0 when cLApFastHbTimerEnabled is set to 'false'. |
| 1.3.6.1.4.1.9.9.513.1.3.1.1.3 | ColumncLApFastHbTimerEnabled | read-write | current | This object controls the Heartbeat Timer. A value of 'true' indicates that this timer is enabled. A value of 'false' indicates that this timer is disabled. |
| 1.3.6.1.4.1.9.9.513.1.3.3 | ScalarcLApPrimaryDiscoveryTimeout | read-write | current | This object represents the timeout for the primary AP discovery. |
| 1.3.6.1.4.1.9.9.513.1.3.4 | ScalarcLApGlobalPrimaryControllerAddressType | read-write | current | This object represents the type of the primary controller's address made available through cLApPrimaryControllerAddress. |
| 1.3.6.1.4.1.9.9.513.1.3.5 | ScalarcLApGlobalPrimaryControllerAddress | read-write | current | This object represents the address of the primary controller that the APs will join. The name and address should be provided in the same set request. An addres… |
| 1.3.6.1.4.1.9.9.513.1.3.6 | ScalarcLApGlobalPrimaryControllerName | read-write | current | This object represents the name of the primary controller that the APs will join. |
| 1.3.6.1.4.1.9.9.513.1.3.7 | ScalarcLApGlobalSecondaryControllerAddressType | read-write | current | This object represents the type of the secondary controller's address made available through cLApSecondaryControllerAddress. |
| 1.3.6.1.4.1.9.9.513.1.3.8 | ScalarcLApGlobalSecondaryControllerAddress | read-write | current | This object represents the address of the secondary controller that the APs will join. The name and address should be provided in the same set request. An addr… |
| 1.3.6.1.4.1.9.9.513.1.3.9 | ScalarcLApGlobalSecondaryControllerName | read-write | current | This object represents the name of the secondary controller that the APs will join. |
| 1.3.6.1.4.1.9.9.513.1.3.10 | ScalarcLApGlobalFailoverPriority | read-write | current | This object represents the Global AP Failover priority. If Enabled, Priorities will be considered of the APs which wishes to join the controller. Preference wi… |
| 1.3.6.1.4.1.9.9.513.1.3.11 | ScalarcLApGlobalTcpMss | read-write | current | This object represents the Global AP TCP MSS value. Permissible value are between 536 and 1363. This will also enable the global TCP MSS flag. Value of 0 will … |
| 1.3.6.1.4.1.9.9.513.1.3.12 | TablecLApGlobalDot11IfTable | not-accessible | current | This table is used to configure the global dot11 parameters per slot id, represented by cLApDot11IfSlotId, of the radio interface in all the APs joined with th… |
| 1.3.6.1.4.1.9.9.513.1.3.12.1 | RowcLApGlobalDot11IfEntry | not-accessible | current | This represents an entry in the cLApGlobalDot11IfTable. |
| 1.3.6.1.4.1.9.9.513.1.3.12.1.1 | ColumncLApGlobalDot11IfCdpEnabled | read-write | current | This object is used to configure the Cisco Discovery Protocol(CDP) in the interface, represented by cLApDot11IfSlotId of the all the APs, joined in the control… |
| 1.3.6.1.4.1.9.9.513.1.3.13 | TablecLApGlobalEthernetIfTable | not-accessible | current | This table is used to configure the global parameters on Ethernet interfaces of all the APs joined with the controller. |
| 1.3.6.1.4.1.9.9.513.1.3.13.1 | RowcLApGlobalEthernetIfEntry | not-accessible | current | This represents an entry in cLApGlobalEthernetIfTable. |
| 1.3.6.1.4.1.9.9.513.1.3.13.1.1 | ColumncLApGlobalEthernetIfCdpEnabled | read-write | current | This object is used to configure the Cisco Discovery Protocol(CDP) in the interface, represented by cLApEthernetIfSlotId of the all the APs, joined in the cont… |
| 1.3.6.1.4.1.9.9.513.1.3.14 | ScalarcLApGlobalRetransmitCount | read-write | current | This object specifies the retransmission count for the Control Packet of all the Access Points, joined to this controller. This value represents the number of … |
| 1.3.6.1.4.1.9.9.513.1.3.15 | ScalarcLApGlobalRetransmitTimeout | read-write | current | This object specifies the retransmission timeout for the Control Packet of all the Access Points, joined to this controller. This value represents the timeout … |
| 1.3.6.1.4.1.9.9.513.1.3.16 | ScalarcLApOeapDisableLocalAccess | read-write | current | This object specifies whether the local access is supported for all the Office Extended Access Points, joined to this controller. If set to true, the local SSI… |
| 1.3.6.1.4.1.9.9.513.1.3.17 | ScalarcLApGlobalLEDState | read-write | current | This object specifies whether the LED state of all the access points should be enabled or disabled. |
| 1.3.6.1.4.1.9.9.513.1.3.18 | ScalarcLApRadioInterfaceShutdownEnabled | read-write | current | This object allows the user to enable or disable AP radio Interface. When enabled, AP radio's will be shut down when Ethernet link goes down for a duration of … |
| 1.3.6.1.4.1.9.9.513.1.3.19 | ScalarcLApEthernetInterfaceDowntime | read-write | current | This object specifies the Ethernet interface down time after which the AP radio interface will be shut down. |
| 1.3.6.1.4.1.9.9.513.1.3.20 | ScalarcLAPMulticastGroupAddressType | read-write | current | This object specifies the AP multicast group address type. |
| 1.3.6.1.4.1.9.9.513.1.3.21 | ScalarcLAPMulticastGroupAddress | read-write | current | This object specifies the AP IPv6 multicast group address. |
| 1.3.6.1.4.1.9.9.513.1.3.22 | ScalarcLAPMulticastMode | read-write | current | This object specifies the switch's ethernet multicast support. unicast - Controller will convert multicast to unicast packet. multicast - Multicast mode is ena… |
| 1.3.6.1.4.1.9.9.513.1.3.23 | ScalarcLApPrimedDiscoveryTimeout | read-write | current | This object represents the primed timeout for the AP discovery. |
| 1.3.6.1.4.1.9.9.513.1.4 | NodeciscoLwappApCredentials | |||
| 1.3.6.1.4.1.9.9.513.1.4.1 | ScalarcLApCredentialGlobalUserName | read-write | current | This object represents the global username for all the APs already joined or will join the controller. This user name is used to access the console on the AP. |
| 1.3.6.1.4.1.9.9.513.1.4.2 | ScalarcLApCredentialGlobalPassword | read-write | current | This object represents the password corresponding to the user name represented by cLApCredentialGlobalUserName object. |
| 1.3.6.1.4.1.9.9.513.1.4.3 | ScalarcLApCredentialGlobalSecret | read-write | current | This object represents the secret key for all the APs already joined or will join the controller. This provides read-write access to the console on the AP. |
| 1.3.6.1.4.1.9.9.513.1.4.4 | TablecLApCredentialsTable | not-accessible | current | This table provides the information about the credentials of the 802.11 LWAPP Access Points that have joined the controller. Rows are added to this table whene… |
| 1.3.6.1.4.1.9.9.513.1.4.4.1 | RowcLApCredentialsEntry | not-accessible | current | Each entry in this table provides information about one 802.11 LWAPP Access Point that has joined the controller. cLApSysMacAddress is the index which uniquely… |
| 1.3.6.1.4.1.9.9.513.1.4.4.1.1 | ColumncLApCredentialUserName | read-create | current | This object represents the username for this AP. |
| 1.3.6.1.4.1.9.9.513.1.4.4.1.2 | ColumncLApCredentialPassword | read-create | current | This object represents the password corresponding to user name represented by cLApCredentialUserName object. |
| 1.3.6.1.4.1.9.9.513.1.4.4.1.3 | ColumncLApCredentialSecret | read-create | current | This object represents the secret key for the specific AP. This provides the read-write access on the console for this AP. |
| 1.3.6.1.4.1.9.9.513.1.4.4.1.4 | ColumncLApCredentialEnableGlobalCredentials | read-create | current | This object specifies whether the global credentials for the AP is enabled or disabled. A value of 'true' enables the global username/password to be used for t… |
| 1.3.6.1.4.1.9.9.513.1.5 | NodeciscoLwappLinkLatency | |||
| 1.3.6.1.4.1.9.9.513.1.5.1 | TablecLApLinkLatencyTable | not-accessible | current | This table represents the link latency configuration for each AP. An entry is automatically added to this table when an Access Points Joins controller. Entry i… |
| 1.3.6.1.4.1.9.9.513.1.5.1.1 | RowcLApLinkLatencyEntry | not-accessible | current | Each entry in this table provides configuration related to Link latency on each AP. |
| 1.3.6.1.4.1.9.9.513.1.5.1.1.1 | ColumncLApLinkLatencyEnable | read-write | current | This object can be used to configure the Link Latency on the AP. A value of 'true' indicates that the Link Latency is enabled. A value of 'false' indicates tha… |
| 1.3.6.1.4.1.9.9.513.1.5.1.1.2 | ColumncLApLinkLatencyReset | read-write | current | This object can be used to reset the Link Latency stored at controller for an AP. A value of true indicates that the Link Latency stats is to be reset. A value… |
| 1.3.6.1.4.1.9.9.513.1.5.2 | TablecLApLinkLatencyStatsTable | not-accessible | current | This table represents the link latency statistics calculated for each AP. An entry is automatically added by the controller when a 'cLApLinkLatencyEnable' is e… |
| 1.3.6.1.4.1.9.9.513.1.5.2.1 | RowcLApLinkLatencyStatsEntry | not-accessible | current | Each entry in this table provides minimum, maximum and average Link latency for a Access Point. Entries are removed when the Link Latency is disabled on a Acce… |
| 1.3.6.1.4.1.9.9.513.1.5.2.1.1 | ColumncLApLinkLatencyStatsCurrent | read-only | current | This object represent the current Link latency recorded for this Access point. |
| 1.3.6.1.4.1.9.9.513.1.5.2.1.2 | ColumncLApLinkLatencyStatsMin | read-only | current | This object represent the minimum Link latency recorded for this Access point. |
| 1.3.6.1.4.1.9.9.513.1.5.2.1.3 | ColumncLApLinkLatencyStatsMax | read-only | current | This object represent the maximum Link latency recorded for this Access point. |
| 1.3.6.1.4.1.9.9.513.1.5.2.1.4 | ColumncLApLinkLatencyTimeStamp | read-only | current | This object represents the timestamp, when the values are collected, as returned by the object 'cLApUpTime'. |
| 1.3.6.1.4.1.9.9.513.1.5.2.1.5 | ColumncLApDataLinkLatencyStatsCurrent | read-only | current | This object represent the current Data Link latency recorded for this Access point. |
| 1.3.6.1.4.1.9.9.513.1.5.2.1.6 | ColumncLApDataLinkLatencyStatsMin | read-only | current | This object represent the minimum Data Link latency recorded for this Access point. |
| 1.3.6.1.4.1.9.9.513.1.5.2.1.7 | ColumncLApDataLinkLatencyStatsMax | read-only | current | This object represent the maximum Data Link latency recorded for this Access point. |
| 1.3.6.1.4.1.9.9.513.1.5.2.1.8 | ColumncLApDataLinkLatencyTimeStamp | read-only | current | This object represents the timestamp, when the values are collected, as returned by the object 'cLApUpTime'. |
| 1.3.6.1.4.1.9.9.513.1.6 | NodeciscoLwappSpectrum | |||
| 1.3.6.1.4.1.9.9.513.1.7 | NodeciscoLwappAp802dot1xSupplicant | |||
| 1.3.6.1.4.1.9.9.513.1.7.1 | ScalarcLApGlobal802dot1xAuthenticationEnabled | read-write | current | This object represents the Global AP 802.1x Supplicant Authentication feature. If configured as True, user can configure 8021.1x authentication between lightwe… |
| 1.3.6.1.4.1.9.9.513.1.7.2 | ScalarcLApGlobal802dot1xSupplicantUsername | read-write | current | This object represents the 802.1x supplicant username that is to be inherited by all access points that join the controller. |
| 1.3.6.1.4.1.9.9.513.1.7.3 | ScalarcLApGlobal802dot1xSupplicantPassword | read-write | current | This object represents the 802.1x supplicant Password that is to be inherited by all access points that join the controller. A query on this OID will always re… |
| 1.3.6.1.4.1.9.9.513.1.7.4 | TablecLAp802dot1xSupplicantTable | not-accessible | current | This table provides the information about the 802.1x Supplicant credentials of the 802.11 LWAPP Access Points that have joined the controller. Rows are added t… |
| 1.3.6.1.4.1.9.9.513.1.7.4.1 | RowcLAp802dot1xSupplicantEntry | not-accessible | current | Each entry in this table provides information about one 802.11 LWAPP Access Point that has joined the controller. cLApSysMacAddress is the index which uniquely… |
| 1.3.6.1.4.1.9.9.513.1.7.4.1.1 | ColumncLAp802dot1xSupplicantOverrideEnabled | read-write | current | This object represents the individual AP level 802.1x Supplicant Authentication override parameters. If configured as True, user can override the Global AP 802… |
| 1.3.6.1.4.1.9.9.513.1.7.4.1.2 | ColumncLAp802dot1xSupplicantOverrideUsername | read-write | current | This object represents the individual AP level 802.1x supplicant override username. |
| 1.3.6.1.4.1.9.9.513.1.7.4.1.3 | ColumncLAp802dot1xSupplicantOverridePassword | read-write | current | This object the individual AP level 802.1x supplicant override password. A query on this OID will always return '****'. |
| 1.3.6.1.4.1.9.9.513.1.8 | TablecLApSeClientTable | not-accessible | current | This table represents the information about the details of Spectrum Expert client connected to radio interface of APs |
| 1.3.6.1.4.1.9.9.513.1.8.1 | RowcLApSeClientEntry | not-accessible | current | An entry in this table represents the details of Spectrum Expert client connected to APs |
| 1.3.6.1.4.1.9.9.513.1.8.1.1 | ColumncLApSeIndex | not-accessible | current | This object indicates the index of the client running the Spectrum Expert instance. |
| 1.3.6.1.4.1.9.9.513.1.8.1.2 | ColumncLApSeClientUserName | read-only | current | This object indicates the name of the client running the Spectrum Expert application |
| 1.3.6.1.4.1.9.9.513.1.8.1.3 | ColumncLApSeClientIPAddrType | read-only | current | This object indicates the client IP address type, that runs the SE application, made available through cLApSeClientIPAddr |
| 1.3.6.1.4.1.9.9.513.1.8.1.4 | ColumncLApSeClientIPAddr | read-only | current | This object indicates the client IP address, that runs the SE application |
| 1.3.6.1.4.1.9.9.513.1.8.1.5 | ColumncLApSeClientDuration | read-only | current | This object indicates the duration for which the SE client application has been up and running |
| 1.3.6.1.4.1.9.9.513.1.8.1.6 | ColumncLApSeClientPort | read-only | current | This object indicates the port from which the SE client application is running |
| 1.3.6.1.4.1.9.9.513.1.9 | NodeciscoLwappApWlanStats | |||
| 1.3.6.1.4.1.9.9.513.1.9.1 | TablecLApWlanStatsTable | not-accessible | current | This table represents Per-AP, Per-Radio, Per-SSID Stats information of packets/bytes sent/received, retransmission counter, associated clients counter, etc. |
| 1.3.6.1.4.1.9.9.513.1.9.1.1 | RowcLApWlanStatsEntry | not-accessible | current | This entry contains stats information of packets/bytes sent/received, retransmission counter, associated clients counter, and etc. |
| 1.3.6.1.4.1.9.9.513.1.9.1.1.1 | ColumncLApWlanStatsTxPktNum | read-only | current | This object represents the transmitted packets counter of the specific radio and wlan on this access point. |
| 1.3.6.1.4.1.9.9.513.1.9.1.1.2 | ColumncLApWlanStatsTxOctetNum | read-only | current | This object represents the transmitted bytes counter of the specific radio and wlan on this access point. |
| 1.3.6.1.4.1.9.9.513.1.9.1.1.3 | ColumncLApWlanStatsRxPktNum | read-only | current | This object represents the received packets counter of the specific radio and wlan on this access point. |
| 1.3.6.1.4.1.9.9.513.1.9.1.1.4 | ColumncLApWlanStatsRxOctetNum | read-only | current | This object represents the received bytes counter of the specific radio and wlan on this access point. |
| 1.3.6.1.4.1.9.9.513.1.9.1.1.5 | ColumncLApWlanStatsRetransmitNum | read-only | current | This object represents the packet retransmission counter of the specific radio and wlan on this access point. |
| 1.3.6.1.4.1.9.9.513.1.9.1.1.6 | ColumncLApWlanStatsAssocClientNum | read-only | current | This object represents the associated client counter of the specific radio and wlan on this access point. |
| 1.3.6.1.4.1.9.9.513.1.9.1.1.7 | ColumncLApWlanStatsOnlineUserNum | read-only | current | This object represents the online user counter of the specific radio and wlan on this access point. |
| 1.3.6.1.4.1.9.9.513.1.10 | NodeciscoLwappApWlanInfo | |||
| 1.3.6.1.4.1.9.9.513.1.10.1 | TablecLApWlanInfoTable | not-accessible | current | This table represents Per-AP, Per-SSID information of max supported clients |
| 1.3.6.1.4.1.9.9.513.1.10.1.1 | RowcLApWlanInfoEntry | not-accessible | current | This entry contains information of max supported clients number |
| 1.3.6.1.4.1.9.9.513.1.10.1.1.1 | ColumncLApWlanInfoMaxClients | read-write | current | This object represents the max supported associated clients of a WLAN on an AP. |
| 1.3.6.1.4.1.9.9.513.1.10.2 | TablecLApRadioWlanInfoTable | not-accessible | current | This table represents Per-AP, Per-RADIO, Per-SSID information. |
| 1.3.6.1.4.1.9.9.513.1.10.2.1 | RowcLApRadioWlanInfoEntry | not-accessible | current | This entry contains information of Per-AP, Per-RADIO, Per-SSID information. |
| 1.3.6.1.4.1.9.9.513.1.10.2.1.1 | ColumncLApRadioWlanSsid | read-only | current | This object represents SSID of the particular WLAN, which is seen on the radio of the AP. |
| 1.3.6.1.4.1.9.9.513.1.10.2.1.2 | ColumncLApRadioWlanBssid | read-only | current | This object represents the BSSID of the SSID on this radio of this AP. |
| 1.3.6.1.4.1.9.9.513.1.11 | NodeciscoLwappPacketDumpInfo | |||
| 1.3.6.1.4.1.9.9.513.1.11.1 | ScalarcLApPacketDumpFtpServerAddressType | read-write | current | This object represents the address type of the Server to which the packet dump is stored. |
| 1.3.6.1.4.1.9.9.513.1.11.2 | ScalarcLApPacketDumpFtpServerAddress | read-write | current | This object represents the address of the Server to which the packet dump is stored. |
| 1.3.6.1.4.1.9.9.513.1.11.3 | ScalarcLApPacketDumpFtpServerPath | read-write | current | This object specifies the directory path for the packet dump storing. The controller remembers the last file path used. |
| 1.3.6.1.4.1.9.9.513.1.11.4 | ScalarcLApPacketDumpFtpUsername | read-write | current | This object is used to store the FTP username for transferring the packet-dump to the FTP server. |
| 1.3.6.1.4.1.9.9.513.1.11.5 | ScalarcLApPacketDumpFtpPassword | read-write | current | This object is used to store the FTP password for transferring the packet-dump to the FTP server. |
| 1.3.6.1.4.1.9.9.513.1.11.6 | ScalarcLApPacketDumpClassifier | read-write | current | This object specifies the Frame Type considered for packet-dump. |
| 1.3.6.1.4.1.9.9.513.1.11.7 | ScalarcLApPacketDumpBufferSize | read-write | current | This object specifies the buffer size considered for packet-dump. |
| 1.3.6.1.4.1.9.9.513.1.11.8 | ScalarcLApPacketDumpCaptureTime | read-write | current | This object specifies the capture time considered for packet-dump. |
| 1.3.6.1.4.1.9.9.513.1.11.9 | ScalarcLApPacketDumpTruncation | read-write | current | This object specifies the length of the packet after truncation |
| 1.3.6.1.4.1.9.9.513.1.11.10 | ScalarcLApPacketDumpApName | read-write | current | This object represents the AP name on which we need to start packet dump. |
| 1.3.6.1.4.1.9.9.513.1.11.11 | ScalarcLApPacketDumpDeviceMacAddress | read-write | current | This object specifies the MAC address of the device for which we need to start packet dump on the AP. |
| 1.3.6.1.4.1.9.9.513.1.11.12 | ScalarcLApPacketDumpStartStop | read-write | current | This object is used to start or stop, packet dump on the associated AP to which the particular mobile station is connected. When value is 'none', it indicates … |
| 1.3.6.1.4.1.9.9.513.1.12 | NodeciscoLwappAplanStats | |||
| 1.3.6.1.4.1.9.9.513.1.12.1 | TablecLAplanStatsTable | not-accessible | current | This table represents Saridinia AP LAN stats information that have joined the controller. |
| 1.3.6.1.4.1.9.9.513.1.12.1.1 | RowcLAplanStatsEntry | not-accessible | current | This entry contains stats information of LAN stats |
| 1.3.6.1.4.1.9.9.513.1.12.1.1.1 | ColumncLApLanPortId | not-accessible | current | This object represents the ID of a LAN Port on Sardinia AP. |
| 1.3.6.1.4.1.9.9.513.1.12.1.1.2 | ColumncLApLanPortState | read-write | current | This object represents the LAN port ID Stats of an Ethernet interface on Sardinia AP. |
| 1.3.6.1.4.1.9.9.513.1.12.1.1.3 | ColumncLApLanPortVlanId | read-write | current | This object represents the VlanID Range(2-4094) and VlanId =0 to disable vlan access of a VLAN LAN Port on Sardinia AP. |
| 1.3.6.1.4.1.9.9.513.1.12.1.1.4 | ColumncLApLanPortVlanIdValid | read-only | current | This object represents VLAN ID is valid for LAN Port interface on Sardinia AP. |
| 1.3.6.1.4.1.9.9.513.2 | NodeciscoLwappApMIBConform | |||
| 1.3.6.1.4.1.9.9.513.2.1 | NodeciscoLwappApMIBCompliances | |||
| 1.3.6.1.4.1.9.9.513.2.1.1 | ComplianceciscoLwappApMIBCompliance | deprecated | The compliance statement for the SNMP entities that implement the ciscoLwappApMIB module. | |
| 1.3.6.1.4.1.9.9.513.2.1.2 | ComplianceciscoLwappApMIBComplianceRev1 | deprecated | The compliance statement for the SNMP entities that implement the ciscoLwappApMIB module. | |
| 1.3.6.1.4.1.9.9.513.2.1.3 | ComplianceciscoLwappApMIBComplianceRev2 | deprecated | The compliance statement for the SNMP entities that implement the ciscoLwappApMIB module. | |
| 1.3.6.1.4.1.9.9.513.2.1.4 | ComplianceciscoLwappApMIBComplianceRev3 | deprecated | The compliance statement for the SNMP entities that implement the ciscoLwappApMIB module. | |
| 1.3.6.1.4.1.9.9.513.2.1.5 | ComplianceciscoLwappApMIBComplianceRev4 | deprecated | The compliance statement for the SNMP entities that implement the ciscoLwappApMIB module. | |
| 1.3.6.1.4.1.9.9.513.2.1.6 | ComplianceciscoLwappApMIBComplianceRev5 | deprecated | The compliance statement for the SNMP entities that implement the ciscoLwappApMIB module. | |
| 1.3.6.1.4.1.9.9.513.2.1.7 | ComplianceciscoLwappApMIBComplianceRev6 | deprecated | The compliance statement for the SNMP entities that implement the ciscoLwappApMIB module. | |
| 1.3.6.1.4.1.9.9.513.2.1.8 | ComplianceciscoLwappApMIBComplianceRev7 | read-only | current | The compliance statement for the SNMP entities that implement the ciscoLwappApMIB module. |
| 1.3.6.1.4.1.9.9.513.2.2 | NodeciscoLwappApMIBGroups | |||
| 1.3.6.1.4.1.9.9.513.2.2.1 | GroupciscoLwappApGroup | current | This collection of objects represents the information about the general attributes and functional parameters of those APs that have joined the controller. | |
| 1.3.6.1.4.1.9.9.513.2.2.2 | GroupciscoLwappApIfGroup | current | This collection of objects represents the information about the dot11 interfaces of those APs that have joined the controller. | |
| 1.3.6.1.4.1.9.9.513.2.2.3 | GroupciscoLwappApGroupSup1 | current | This supplemental collection of objects represents the information about the general attributes and functional parameters of those APs that have joined the con… | |
| 1.3.6.1.4.1.9.9.513.2.2.4 | GroupciscoLwappApGroupSup2 | current | This supplemental collection of objects represents the name associated with those APs that have joined the controller. | |
| 1.3.6.1.4.1.9.9.513.2.2.5 | GroupciscoLwappApGroupSup3 | current | This supplemental collection of objects represents the country and 802.11n related information for those APs that have joined the controller. | |
| 1.3.6.1.4.1.9.9.513.2.2.6 | GroupciscoLwappApNotifObjsGroup | current | This supplemental collection of objects represents the information carried by the AP related notifications sent by the agent to a network management station. | |
| 1.3.6.1.4.1.9.9.513.2.2.7 | GroupciscoLwappApNotifsGroup | deprecated | This supplemental collection of objects represents the AP related notifications sent by the agent to a network management station. ciscoLwappApNotifsGroup obje… | |
| 1.3.6.1.4.1.9.9.513.2.2.8 | GroupciscoLwappApGroupSup4 | deprecated | This supplemental collection of objects represents the global and credential information for those APs that have joined the controller. ciscoLwappApGroupSup4 o… | |
| 1.3.6.1.4.1.9.9.513.2.2.9 | GroupciscoLwappApEthernetIfGroup | current | This collection of objects represents the information about the Ethernet interfaces of those APs that have joined the controller. | |
| 1.3.6.1.4.1.9.9.513.2.2.10 | GroupciscoLwappApRadioGroup | current | This collection of objects represents the information about the Radios of those APs that have joined the controller. | |
| 1.3.6.1.4.1.9.9.513.2.2.11 | GroupciscoLwappApGroupSup5 | current | This supplemental collection of objects represents objects related to encryption and link latency of AP. | |
| 1.3.6.1.4.1.9.9.513.2.2.12 | GroupciscoLwappSeClientSup | current | This supplemental collection of objects represents the Spectrum Expert client details connected to the APs. | |
| 1.3.6.1.4.1.9.9.513.2.2.13 | GroupciscoLwappDot11IfAntennaGroup | current | This supplemental collection of objects represents the antenna details corresponding to the dot11 interface of the Access Points. | |
| 1.3.6.1.4.1.9.9.513.2.2.14 | GroupciscoLwappRetransmitGroup | current | This supplemental collection of objects represents the retransmit parameters corresponding to the fallback of an AccessPoint to another controller during failo… | |
| 1.3.6.1.4.1.9.9.513.2.2.15 | GroupciscoLwappApGroupSup6 | current | This supplemental collection of objects represents the global and credential information for those APs that have joined the controller. | |
| 1.3.6.1.4.1.9.9.513.2.2.16 | GroupciscoLwappApNotifsGroupVer1 | current | This supplemental collection of objects represents the AP related notifications sent by the agent to a network management station. | |
| 1.3.6.1.4.1.9.9.513.2.2.17 | GroupciscoLwappApGroupSup7 | current | This supplemental collection of objects represents the information about the general attributes and functional parameters of those APs that have joined the con… | |
| 1.3.6.1.4.1.9.9.513.3 | NodeciscoLwappApMIBNotifObjects | |||
| 1.3.6.1.4.1.9.9.513.3.1 | ScalarcLApAssocFailureReason | accessible-for-notify | current | This object specifies the failure reasons when a AP fails to associate with a controller. |
| 1.3.6.1.4.1.9.9.513.3.2 | ScalarcLApRogueApMacAddress | accessible-for-notify | current | This object represents the radio MAC address common to the dot11 interfaces of the rogue AP. |
| 1.3.6.1.4.1.9.9.513.3.3 | ScalarcLApDot11RadioChannelNumber | accessible-for-notify | current | This object represents the channel number of the radio interface of the AP, represented by cLApDot11IfType. |
| 1.3.6.1.4.1.9.9.513.3.4 | ScalarcLApRogueApSsid | accessible-for-notify | current | This object represents the SSID used by the rogue AP to intrude the network. |
| 1.3.6.1.4.1.9.9.513.3.5 | ScalarcLApRogueType | accessible-for-notify | current | This object represents the SSID of the used by the rogue AP to intrude the network. |
| 1.3.6.1.4.1.9.9.513.3.6 | ScalarcLApWipsReason | accessible-for-notify | current | This object specifies the failure reasons for an AP when cLApWipsEnable is set to 'true'. noMonitoringDevice - No monitoring device connected to collect WIPs i… |
| 1.3.6.1.4.1.9.9.513.3.7 | ScalarcLApWipsClear | accessible-for-notify | current | This object specifies whether this event is raise or clear. A value of 'true' indicates this event is cleared A value of 'false' indicates this even is raised. |
| 1.3.6.1.4.1.9.9.513.3.8 | ScalarcLApIfUpDownFailureType | accessible-for-notify | current | This object specifies the type of the AP interface failure. detectedFailure(1) - Failure of radio. configuredReset(2) - Reset due to manual configuration. |
| 1.3.6.1.4.1.9.9.513.3.9 | ScalarcLApIfUpDownCause | accessible-for-notify | current | This object specifies the cause of the AP interface failure. |
| 1.3.6.1.4.1.9.9.513.3.10 | ScalarcLApIfUpDownFailureCode | accessible-for-notify | current | This object specifies the code of the AP interface failure. |
| 1.3.6.1.4.1.9.9.513.3.11 | ScalarcLApAlarmSet | accessible-for-notify | current | This object specifies whether this event is raise or clear. A value of 'true' indicates this event is set. A value of 'false' indicates this even is cleared. |
| 1.3.6.1.4.1.9.9.513.3.12 | ScalarcLApRogueClassType | accessible-for-notify | current | This object specifies the AP class type of the Rogue AP detected. |
| 1.3.6.1.4.1.9.9.513.3.13 | ScalarcLApRogueDetectedChannel | accessible-for-notify | current | This object represents the rogue detected channel number. |
| 1.3.6.1.4.1.9.9.513.3.14 | ScalarcLApRSSI | accessible-for-notify | current | This object specifies the Rogue RSSI as seen by AP Interface. |
| 1.3.6.1.4.1.9.9.513.3.15 | ScalarcLApSNR | accessible-for-notify | current | This object specifies the SNR seen by AP Interface from Rogue |
| 1.3.6.1.4.1.9.9.513.3.16 | ScalarcLApDot11RadioCurrentChannel | accessible-for-notify | current | This object represents the dot11 current channel. |
| 1.3.6.1.4.1.9.9.513.3.17 | ScalarcLApAdhocRogue | accessible-for-notify | current | This object represents the flag used to state if the rogue found is an Adhoc rogue or it is an AP. |
| 1.3.6.1.4.1.9.9.513.3.18 | ScalarcLApRogueAPOnWiredNetwork | accessible-for-notify | current | This object represents the flag used to state if the rogue is found on the wired network. A value of 'true' indicates Rogue AP is found on wired network. A val… |
| 1.3.6.1.4.1.9.9.513.3.19 | ScalarcLApRogueMode | accessible-for-notify | current | This attribute is use to specify the state in which the Rogue AP is user can set the Rogue AP in alert, known or acknowledge state. Alert state means Rogue AP … |
| 1.3.6.1.4.1.9.9.513.3.20 | ScalarcLApRogueIsClassifiedByRule | accessible-for-notify | current | This object represents the flag used to state if the rogue is classified by a rogue rule. A value of 'true' indicates its classifed by rogue rule. A value of '… |
| 1.3.6.1.4.1.9.9.513.3.21 | ScalarcLApRogueClassifiedApMacAddress | accessible-for-notify | current | This object represents the radio MAC address of the classified rogue AP. |
| 1.3.6.1.4.1.9.9.513.3.22 | ScalarcLApRogueClassifiedRSSI | accessible-for-notify | current | This object represents the Rogue classified RSSI as seen by Airespace AP Interface. |
| 1.3.6.1.4.1.9.9.513.3.23 | ScalarcLAPPreviousMonitorMode | accessible-for-notify | current | This object represents the previous AP monitor Mode. |
| 1.3.6.1.4.1.9.9.513.3.24 | ScalarcLAPCurrentMonitorMode | accessible-for-notify | current | This object represents the current AP monitor Mode. |
| 1.3.6.1.4.1.9.9.513.3.25 | ScalarcLApSsidKeyConfSsidA | accessible-for-notify | current | This object represents the SSID which has same cipher key with another SSID on the same AP. The another SSID is represented by cLApSsidKeyConfSsidB. |
| 1.3.6.1.4.1.9.9.513.3.26 | ScalarcLApSsidKeyConfKeyIdxA | accessible-for-notify | current | This object represents key index of the SSID which has same cipher key with another SSID on the same AP. It is the key index of cLApSsidKeyConfSsidA. The anoth… |
| 1.3.6.1.4.1.9.9.513.3.27 | ScalarcLApSsidKeyConfSsidB | accessible-for-notify | current | This object represents the SSID which has same cipher key with another SSID on the same AP. The another SSID is represented by cLApSsidKeyConfSsidA. |
| 1.3.6.1.4.1.9.9.513.3.28 | ScalarcLApSsidKeyConfKeyIdxB | accessible-for-notify | current | This object represents key index of the SSID which has same cipher key with another SSID on the same AP. It is the key index of cLApSsidKeyConfSsidB. The anoth… |
| 1.3.6.1.4.1.9.9.513.3.29 | ScalarcLApPreviousChannel | accessible-for-notify | current | This object represents the channel before changed. |
| 1.3.6.1.4.1.9.9.513.3.30 | ScalarcLApCurrentChannel | accessible-for-notify | current | This object represents the channel after changed. |
| 1.3.6.1.4.1.9.9.513.3.31 | ScalarcLApChannelCustomize | accessible-for-notify | current | This object represents the channel's change mode. If this value is true, then bsnAPDot11CurrentChannel in bsnAPIfDot11PhyDSSSTable is assigned by dynamic algor… |
| 1.3.6.1.4.1.9.9.513.3.32 | ScalarcLApIfLoadChannelUtilization | accessible-for-notify | current | This object specifies the code of the AP Interface channel load utilization. |
| 1.3.6.1.4.1.9.9.513.3.33 | ScalarcLAPGroupVlanName | accessible-for-notify | current | This object specifies the code of the AP Group Interface Name. |
| 1.3.6.1.4.1.9.9.513.3.34 | ScalarcLApRuleName | accessible-for-notify | current | This object represents the rule name to identify applied on the Ap. |
| 1.3.6.1.4.1.9.9.513.3.35 | ScalarcLApSeverityScore | accessible-for-notify | current | This object is used to define the custom classification severity score of the rules. This object is applicable when cLRuleRogueType is configured as 'custom'. |