MIB Viewer

CISCO-LWAPP-DOT11-CLIENT-MIB

177 objects
This MIB is intended to be implemented on all those devices operating as Central controllers, that terminate the Light Weight Access Point Protocol tunnel from Cisco Light-weight LWAPP Access Points. Information provided by this MIB is about the configuration and monitoring of 802.11 wireless clients in the network. The relationship between CC and the LWAPP APs can be depicted as follows: +......+ +......+ +......+ +......+ + + + + + + + + + CC + + CC + + CC + + CC + + + + + + + + + +......+ +......+ +......+ +......+ .. . . . .. . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + AP + + AP + + AP + + AP + + AP + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ . . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + MN + + MN + + MN + + MN + + MN + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ The LWAPP tunnel exists between the controller and the APs. The MNs communicate with the APs through the protocol defined by the 802.11 standard. LWAPP APs, upon bootup, discover and join one of the controllers and the controller pushes the configuration, that includes the WLAN parameters, to the LWAPP APs. The APs then encapsulate all the 802.11 frames from wireless clients inside LWAPP frames and forward the LWAPP frames to the controller. GLOSSARY Access Point ( AP ) An entity that contains an 802.11 medium access control ( MAC ) and physical layer ( PHY ) interface and provides access to the distribution services via the wireless medium for associated clients. LWAPP APs encapsulate all the 802.11 frames in LWAPP frames and sends them to the controller to which it is logically connected. Basic Service Set ( BSS ) Coverage area of one access point is called a BSS. An access point (AP) acts as a master to control the clients within that BSS. Clear To Send (CTS) Refer to the description of RTS. Light Weight Access Point Protocol ( LWAPP ) This is a generic protocol that defines the communication between the Access Points and the Central Controller. MAC Service Data Units ( MSDU ) The MSDU is that unit of data received from the logical link control ( LLC ) sub-layer which lies above the medium access control ( MAC ) sub-layer in a protocol stack. Message Integrity Code ( MIC ) A value generated by a symmetric key cryptographic function. If the input data are changed, a new value cannot be correctly computed without knowledge of the symmetric key. Thus, the secret key protects the input data from undetectable alteration. Mobile Node ( MN ) A roaming 802.11 wireless device in a wireless network associated with an access point. Mobile Node, Mobile Station(Ms) and client are used interchangeably. Request To Send ( RTS ) A client wishing to send data initiates the process by sending a Request To Send (RTS) frame. The destination client replies with a Clear To Send (CTS) frame. Wireless local-area network ( WLAN ) A local-area network that uses high-frequency radio waves rather than wires to communicate between nodes. Service Set Identifier (SSID) A service set identifier is a name that identifies a particular 802.11 wireless LAN. A client device receives broadcast messages from all access points within range advertising their SSIDs. The client device can then either manually or automatically based on configuration select the network with which to associate. The SSID can be up to 32 characters long. Hybrid Remote Edge Access Point (HREAP) HREAP is a wireless solution for branch office and remote office deployments. It enables customers to configure and control access points in a branch or remote office from the corporate office through a wide area network (WAN) link without deploying a controller in each office. Workgroup Bridge ( WGB ) A WGB can provide a wireless infrastructure connection for a Ethernet-enabled devices. Devices that do not have a wireless client adapter in order to connect to the wireless network can be connected to a WGB through Ethernet port. KTS (Key Telephone System) Key Telephone System is an alternative to a private branch exchange (PBX) phone system. A KTS is equipped with several buttons that allow a caller to directly select outgoing lines or incoming calls, and use intercom and conference facilities. REFERENCE [1] Wireless LAN Medium Access Control ( MAC ) and Physical Layer ( PHY ) Specifications [2] Draft-obara-capwap-lwapp-00.txt, IETF Light Weight Access Point Protocol
Imported Objects
CISCO-LWAPP-AP-MIBcLApDot11IfSlotId cLApDot11RadioChannelNumber cLAPGroupVlanName cLApIfLoadChannelUtilization cLApLocation cLApName cLApSubMode
CISCO-LWAPP-MOBILITY-EXT-MIBcLMobilityExtMCClientAnchorMCGroupId cLMobilityExtMCClientAnchorMCPrivateAddress cLMobilityExtMCClientAnchorMCPrivateAddressType cLMobilityExtMCClientAssociatedMAAddress cLMobilityExtMCClientAssociatedMAAddressType cLMobilityExtMCClientAssociatedMCAddress cLMobilityExtMCClientAssociatedMCAddressType cLMobilityExtMCClientAssociatedMCGroupId
CISCO-LWAPP-TC-MIBCcxServiceVersion CLApIfType CLClientPowerSaveMode CLDot11ClientStatus
CISCO-SMIciscoMgmt
CISCO-TCCiscoURLStringOrEmpty
INET-ADDRESS-MIBInetAddress InetAddressType
Q-BRIDGE-MIBVlanId
SNMP-FRAMEWORK-MIBSnmpAdminString
SNMPv2-CONFMODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP
SNMPv2-SMICounter64 IpAddress MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32
SNMPv2-TCDisplayString MacAddress RowStatus TimeInterval TimeStamp TruthValue
OIDNameAccessStatusDescription
1.3.6.1.4.1.9.9.599IdentityciscoLwappDot11ClientMIBThis MIB is intended to be implemented on all those devices operating as Central controllers, that terminate the Light Weight Access Point Protocol tunnel from…
1.3.6.1.4.1.9.9.599.0NodeciscoLwappDot11ClientMIBNotifs
1.3.6.1.4.1.9.9.599.0.1NotificationciscoLwappDot11ClientKeyDecryptErrorcurrentThis notification is generated when a decrypt error occurs. The WEP WPA or WPA2 Key configured at the station may be wrong. cldcAssociationMode represents the …
1.3.6.1.4.1.9.9.599.0.2NotificationciscoLwappDot11ClientAssocNacAlertcurrentThis notification is generated when the client on NAC enabled SSIDs complete layer2 authentication . This is to inform about client's presence to the NAC appli…
1.3.6.1.4.1.9.9.599.0.3NotificationciscoLwappDot11ClientDisassocNacAlertcurrentThis notification is generated when the controller removes the client entry on NAC enabled SSIDs. cldcClientWlanProfileName represents the profile name of the …
1.3.6.1.4.1.9.9.599.0.4NotificationciscoLwappDot11ClientMovedToRunStatecurrentThis notification is generated when the client completes the PEM state and moves to the RUN state. cldcClientUsername represents the username used by the clien…
1.3.6.1.4.1.9.9.599.0.5NotificationciscoLwappDot11ClientStaticIpFailTrapcurrentThis is issued whenever the subnet defined for the Static IP of a Client is not found.
1.3.6.1.4.1.9.9.599.0.6NotificationciscoLwappDot11ClientDisassocDataStatsTrapcurrentThe disassociate notification shall be sent when the Station sends a Disassociation frame. The value of the notification shall include the MAC address of the M…
1.3.6.1.4.1.9.9.599.0.7NotificationciscoLwappDot11ClientAssocDataStatsTrapcurrentThe associate notification shall be sent when the Station sends a association frame.
1.3.6.1.4.1.9.9.599.0.8NotificationciscoLwappDot11ClientSessionTrapcurrentIssued when the client completes the PEM state and moves to the RUN state.
1.3.6.1.4.1.9.9.599.0.9NotificationciscoLwappDot11ClientAssocTrapcurrentThe notification shall be sent when the Station associats to controller.
1.3.6.1.4.1.9.9.599.0.10NotificationciscoLwappDot11ClientDeAuthenticatedTrapcurrentThe notification shall be sent when the Station gets de-authenticated.
1.3.6.1.4.1.9.9.599.0.11NotificationciscoLwappDot11ClientMovedToRunStateNewTrapcurrentThe notification shall be sent when the Station moves to run or authenticated state.
1.3.6.1.4.1.9.9.599.0.12NotificationciscoLwappDot11ClientMobilityTrapcurrentThe notification shall be sent when the Station gets roamed.
1.3.6.1.4.1.9.9.599.1NodeciscoLwappDot11ClientMIBObjects
1.3.6.1.4.1.9.9.599.1.1NodecldcConfigObjects
1.3.6.1.4.1.9.9.599.1.1.1ScalarcldcKeyDecryptErrorEnabledread-writecurrentThe object to control the generation of ciscoLwappDot11ClientKeyDecryptError notification. A value of 'true' indicates that the agent generates ciscoLwappDot11…
1.3.6.1.4.1.9.9.599.1.1.2ScalarcldcAssocNacAlertEnabledread-writecurrentThe object to control the generation of ciscoLwappDot11ClientAssocNacAlert notification. A value of 'true' indicates that the agent generates ciscoLwappDot11Cl…
1.3.6.1.4.1.9.9.599.1.1.3ScalarcldcDisassocNacAlertEnabledread-writecurrentThe object to control the generation of ciscoLwappDot11ClientDisassocNacAlert notification. A value of 'true' indicates that the agent generates ciscoLwappDot1…
1.3.6.1.4.1.9.9.599.1.1.4ScalarcldcMovedToRunStateEnabledread-writecurrentThe object to control the generation of ciscoLwappDot11ClientMovedToRunState notification. A value of 'true' indicates that the agent generates ciscoLwappDot11…
1.3.6.1.4.1.9.9.599.1.1.5ScalarciscoLwappDot11ClientStaticIpFailTrapEnabledread-writecurrentThe object to control the generation of ciscoLwappDot11ClientStaticIpFailTrap notification. A value of 'true' indicates that the agent generates ciscoLwappDot1…
1.3.6.1.4.1.9.9.599.1.2NodecldcNotifObjects
1.3.6.1.4.1.9.9.599.1.2.1ScalarcldcClientRSSIaccessible-for-notifycurrentThis object specifies the average RSSI for the Mobile Station.
1.3.6.1.4.1.9.9.599.1.2.2ScalarcldcClientSNRaccessible-for-notifycurrentThis object specifies the average SNR for the Mobile Station.
1.3.6.1.4.1.9.9.599.1.2.3ScalarcldcDOT11ClientReasonCodeaccessible-for-notifycurrentunspecified - Unspecified. previousAuthNotValid - Previous Authentication was not valid. deauthenticationLeaving - Leaving due to deauthentication. disassociat…
1.3.6.1.4.1.9.9.599.1.2.4ScalarcldcDOT11ClientTxDataPacketsaccessible-for-notifycurrentThis is the number of data packets sent by this mobile station
1.3.6.1.4.1.9.9.599.1.2.5ScalarcldcDOT11ClientTxDataBytesaccessible-for-notifycurrentThis is the number of data bytes sent by this mobile station
1.3.6.1.4.1.9.9.599.1.2.6ScalarcldcDOT11ClientRxDataPacketsaccessible-for-notifycurrentThis is the number of data packets sent for this mobile station
1.3.6.1.4.1.9.9.599.1.2.7ScalarcldcDOT11ClientRxDataBytesaccessible-for-notifycurrentThis is the number of data bytes sent for this mobile station
1.3.6.1.4.1.9.9.599.1.2.8ScalarcldcClientVlanIdaccessible-for-notifycurrentVlan ID of the Interface to which the client is associated.
1.3.6.1.4.1.9.9.599.1.2.9ScalarcldcClientPolicyTypeaccessible-for-notifycurrentMode of the AP to which the Mobile Station is associated.
1.3.6.1.4.1.9.9.599.1.2.10ScalarcldcClientEapTypeaccessible-for-notifycurrentMode of the AP to which the Mobile Station is associated.
1.3.6.1.4.1.9.9.599.1.2.11ScalarcldcClientAIDaccessible-for-notifycurrentAID for the mobile station
1.3.6.1.4.1.9.9.599.1.2.12ScalarcldcClientAuthenticationAlgorithmaccessible-for-notifycurrentAuthentication Algorithm of Mobile Station
1.3.6.1.4.1.9.9.599.1.2.13ScalarcldcClientWepStateaccessible-for-notifycurrentWEP State of Mobile Station
1.3.6.1.4.1.9.9.599.1.2.14ScalarcldcClientEncryptionCypheraccessible-for-notifycurrentMode of the AP to which the Mobile Station is associated.
1.3.6.1.4.1.9.9.599.1.2.15ScalarcldcClientPortNumberaccessible-for-notifycurrentThe Port Number of this Airespace Switch on which the traffic of the Mobile Station is coming through.
1.3.6.1.4.1.9.9.599.1.2.16ScalarcldcClientAnchorAddressTypeaccessible-for-notifycurrentThis object indicates mobility Anchor address type.
1.3.6.1.4.1.9.9.599.1.2.17ScalarcldcClientAnchorAddressaccessible-for-notifycurrentIf the Mobility Status of the Mobile Station is Anchor then it will have Peer Ip Address and will have Anchor IP if the Role is Foreign
1.3.6.1.4.1.9.9.599.1.2.18ScalarcldcClientEssIndexaccessible-for-notifycurrentEss Index of the Wlan(SSID) that is being used by Mobile Station to connect to AP
1.3.6.1.4.1.9.9.599.1.2.19ScalarcldcClientCcxVersionaccessible-for-notifycurrentRepresents the Cisco Compatible Extensions (CCX) Version the client is using for communication with the AP.
1.3.6.1.4.1.9.9.599.1.2.20ScalarcldcClientE2eVersionaccessible-for-notifycurrentRepresents the End-2-End Version the client is using for communication with the AP.
1.3.6.1.4.1.9.9.599.1.2.21ScalarcldcClientInterfaceaccessible-for-notifycurrentName of the Interface of the mobile client to the switch.
1.3.6.1.4.1.9.9.599.1.2.22ScalarcldcClientMobilityStatusaccessible-for-notifycurrentMobility Role of the Mobile Station.
1.3.6.1.4.1.9.9.599.1.2.23ScalarcldcClientStatusCodeaccessible-for-notifycurrentStatus Code of the Mobile Station
1.3.6.1.4.1.9.9.599.1.2.24ScalarcldcClientDeleteActionaccessible-for-notifycurrentAction to Deauthenticate the Mobile Station. Set the State to delete.
1.3.6.1.4.1.9.9.599.1.2.25ScalarcldcClientSecurityPolicyStatusaccessible-for-notifycurrentWhen this attribute has value completed, it shall indicate that the Mobile Station has completed the security policy checks. Otherwise the checks are yet to be…
1.3.6.1.4.1.9.9.599.1.2.26ScalarcldcClientTrapEventTimeaccessible-for-notifycurrentThis object represents the inet address of the Client.
1.3.6.1.4.1.9.9.599.1.2.27ScalarcldcClientPolicyManagerStateaccessible-for-notifycurrentThis object represents the current policy enforcement manager state of the client in controller.
1.3.6.1.4.1.9.9.599.1.2.28ScalarcldcClientAssocTimeaccessible-for-notifycurrentThis object indicates the value of client association time
1.3.6.1.4.1.9.9.599.1.2.29ScalarcldcClientPmipDataValidaccessible-for-notifycurrentThis object represents whether client has valid PMIP data.
1.3.6.1.4.1.9.9.599.1.2.30ScalarcldcClientMobilityExtDataValidaccessible-for-notifycurrentThis object represents new mobility status.
1.3.6.1.4.1.9.9.599.1.2.31ScalarcldcClientPolicyErrorsaccessible-for-notifycurrentNumber of Policy Errors for Mobile Station
1.3.6.1.4.1.9.9.599.1.2.32ScalarcldcClientSessionIdaccessible-for-notifycurrentThis object indicates the session to which the client is associated.
1.3.6.1.4.1.9.9.599.1.2.33ScalarcldcClientPmipNaiaccessible-for-notifycurrentThis object indicates the name of the profile, the client is associated to.
1.3.6.1.4.1.9.9.599.1.2.34ScalarcldcClientPmipStateaccessible-for-notifycurrentThis object indicates the state of the PMIP client: null: binding doesn't exist init: binding created, Retx timer running for PBU, binding not yet accepted fro…
1.3.6.1.4.1.9.9.599.1.2.35ScalarcldcClientPmipInterfaceaccessible-for-notifycurrentThis object indicates the interface to which the client is associated.
1.3.6.1.4.1.9.9.599.1.2.36ScalarcldcClientPmipHomeAddrTypeaccessible-for-notifycurrentThis object indicates the type of the Client's Home address made available through cldcClientPmipHomeAddress.
1.3.6.1.4.1.9.9.599.1.2.37ScalarcldcClientPmipHomeAddraccessible-for-notifycurrentThis object indicates the Home Address of the client.
1.3.6.1.4.1.9.9.599.1.2.38ScalarcldcClientPmipAttaccessible-for-notifycurrentThis object indicates the access technology type by which the client is currently attached.
1.3.6.1.4.1.9.9.599.1.2.39ScalarcldcClientPmipLocalLinkIdaccessible-for-notifycurrentThis object indicates the local link identifier of the client.
1.3.6.1.4.1.9.9.599.1.2.40ScalarcldcClientPmipLmaNameaccessible-for-notifycurrentThis object indicates the LMA to which the client is connected.
1.3.6.1.4.1.9.9.599.1.2.41ScalarcldcClientPmipLifeTimeaccessible-for-notifycurrentThis object indicates the duration of the PMIP client association.
1.3.6.1.4.1.9.9.599.1.2.42ScalarcldcClientPmipDomainNameaccessible-for-notifycurrentThis object indicates the domain to which the PMIP client is associated.
1.3.6.1.4.1.9.9.599.1.2.43ScalarcldcClientPmipUpKeyaccessible-for-notifycurrentThis object indicates the upstream key of the PMIP client.
1.3.6.1.4.1.9.9.599.1.2.44ScalarcldcClientPmipDownKeyaccessible-for-notifycurrentThis object indicates the downstream key of the PMIP client.
1.3.6.1.4.1.9.9.599.1.3NodecldcStatusObjects
1.3.6.1.4.1.9.9.599.1.3.1TablecldcClientTablenot-accessiblecurrentThis table represents the 802.11 wireless clients that are associated with the APs that have joined this controller. An entry is created automatically by the c…
1.3.6.1.4.1.9.9.599.1.3.1.1RowcldcClientEntrynot-accessiblecurrentEach entry represents a conceptual row in this table and provides the information about the clients associated to the APs that have joined the controller. An e…
1.3.6.1.4.1.9.9.599.1.3.1.1.1ColumncldcClientMacAddressnot-accessiblecurrentThis object specifies the MAC address of the client for this entry and uniquely identifies this entry.
1.3.6.1.4.1.9.9.599.1.3.1.1.2ColumncldcClientStatusread-onlycurrentThe object that represents the current status of the client.
1.3.6.1.4.1.9.9.599.1.3.1.1.3ColumncldcClientWlanProfileNameread-onlycurrentThis object specifies the WLAN Profile name this 802.11 wireless client is connected to.
1.3.6.1.4.1.9.9.599.1.3.1.1.4ColumncldcClientWgbStatusread-onlycurrentThe object that represents the work group bridging status of a DOT11 client. 'regClient' - The client is a wireless client 'wgbClient' - The client is connecte…
1.3.6.1.4.1.9.9.599.1.3.1.1.5ColumncldcClientWgbMacAddressread-onlycurrentThis object specifies the MAC address of the WGB this 802.11 wireless client to which it is connected. This returns a non-zero value when the cldcClientWgbStat…
1.3.6.1.4.1.9.9.599.1.3.1.1.6ColumncldcClientProtocolread-onlycurrentThe 802.11 protocol type of the client. 'dot11a' - The client is using 802.11a standard to connect to the access point (AP) 'dot11b' - The client is using 802.…
1.3.6.1.4.1.9.9.599.1.3.1.1.7ColumncldcAssociationModeread-onlycurrentThe association mode for which the key decrypt error occurred.
1.3.6.1.4.1.9.9.599.1.3.1.1.8ColumncldcApMacAddressread-onlycurrentThis object specifies the radio MAC address of a LWAPP AP.
1.3.6.1.4.1.9.9.599.1.3.1.1.9ColumncldcIfTyperead-onlycurrentThis object specifies the wireless interface type.
1.3.6.1.4.1.9.9.599.1.3.1.1.10ColumncldcClientIPAddressread-onlycurrentThis object specified client's IP address.
1.3.6.1.4.1.9.9.599.1.3.1.1.11ColumncldcClientNacStateread-writecurrentThis object specifies the client's network admission control state. 'quarantine' - The client goes through posture analysis and the client traffic is sent by c…
1.3.6.1.4.1.9.9.599.1.3.1.1.12ColumncldcClientQuarantineVLANread-onlycurrentThis object indicates the quarantine VLAN for client. The quarantine VLAN only allows limited access to the network.
1.3.6.1.4.1.9.9.599.1.3.1.1.13ColumncldcClientAccessVLANread-onlycurrentThis object indicates the access VLAN for client. The access VLAN allows unlimited access to the network.
1.3.6.1.4.1.9.9.599.1.3.1.1.14ColumncldcClientLoginTimeread-onlycurrentThis object indicates the value of sysUpTime when the client logged in.
1.3.6.1.4.1.9.9.599.1.3.1.1.15ColumncldcClientUpTimeread-onlycurrentThis object indicates the duration for which the client has been associated with this device.
1.3.6.1.4.1.9.9.599.1.3.1.1.16ColumncldcClientPowerSaveModeread-onlycurrentThis object indicates the power management mode of the client.
1.3.6.1.4.1.9.9.599.1.3.1.1.17ColumncldcClientCurrentTxRateSetread-onlycurrentThis object indicates the current data rate at which the client transmits and receives data. The data rate field is a 16-bit unsigned value expressing the data…
1.3.6.1.4.1.9.9.599.1.3.1.1.18ColumncldcClientDataRateSetread-onlycurrentThis object indicates the set of data rates at which the client may transmit data. Each client can support up to 126 rates. Each octet contains an integer valu…
1.3.6.1.4.1.9.9.599.1.3.1.1.19ColumncldcClientHreapApAuthread-onlycurrentThis object indicates whether the client is locally authenticated or authenticated by the controller. Local authentication is done only if the Access Point con…
1.3.6.1.4.1.9.9.599.1.3.1.1.20ColumncldcClient80211uCapableread-onlycurrentThis object indicates whether the client supports 802.11u feature. The 802.11u standard allows devices such as laptop computers or cellular phones to join a wi…
1.3.6.1.4.1.9.9.599.1.3.1.1.21ColumncldcClientPostureStateread-onlycurrentThis object indicates the Posture state of the client. Posture Analysis is a state change where the client applies the configured policies to validate access t…
1.3.6.1.4.1.9.9.599.1.3.1.1.22ColumncldcClientAclNameread-onlycurrentThis object indicates the ACL Name for the client.
1.3.6.1.4.1.9.9.599.1.3.1.1.23ColumncldcClientAclAppliedread-onlycurrentThis object indicates the ACL applied status for the client. A value of 'true' indicates that the ACL is applied. A value of 'false' indicates that the ACL is …
1.3.6.1.4.1.9.9.599.1.3.1.1.24ColumncldcClientRedirectUrlread-onlycurrentThis object indicates the AAA override redirect URL for a client with cldcClientPostureState enabled. The object has a valid value when the WLAN, with which th…
1.3.6.1.4.1.9.9.599.1.3.1.1.25ColumncldcClientAaaOverrideAclNameread-onlycurrentThis object indicates the AAA Override ACL Name for the client if cldcClientPostureState is enabled on the wlan.
1.3.6.1.4.1.9.9.599.1.3.1.1.26ColumncldcClientAaaOverrideAclAppliedread-onlycurrentThis object indicates the AAA Override ACL applied status for the client if cldcClientPostureState is enabled on the wlan. A value of 'true' indicates that the…
1.3.6.1.4.1.9.9.599.1.3.1.1.27ColumncldcClientUsernameread-onlycurrentThis object represents the username used by the client.
1.3.6.1.4.1.9.9.599.1.3.1.1.28ColumncldcClientSSIDread-onlycurrentThis object represents the SSID of the WLAN to which the client is associated.
1.3.6.1.4.1.9.9.599.1.3.1.1.29ColumncldcClientSecurityTagIdread-onlycurrentThis object represents the security group tag of the client. This parameter will have a non-zero value when the client is DOT1X authenticated.
1.3.6.1.4.1.9.9.599.1.3.1.1.30ColumncldcClientTypeKTSread-onlycurrentThis object indicates whether the Client is NEC KTS Client or not. A value of 'true' indicates that the client follows NEC KTS SIP protocol. A value of 'false'…
1.3.6.1.4.1.9.9.599.1.3.1.1.31ColumncldcClientIpv6AclNameread-onlycurrentThis object specifies the ACL Name for the Ipv6 client.
1.3.6.1.4.1.9.9.599.1.3.1.1.32ColumncldcClientIpv6AclAppliedread-onlycurrentThis object indicates the ACL applied status for the IPv6 client. A value of 'true' indicates that the ACL is applied. A value of 'false' indicates that the AC…
1.3.6.1.4.1.9.9.599.1.3.1.1.33ColumncldcClientDataSwitchingread-onlycurrentThis object specifies whether client is switching data locally or centrally.
1.3.6.1.4.1.9.9.599.1.3.1.1.34ColumncldcClientAuthenticationread-onlycurrentThis object specifies whether client is authentiated locally or centrally.
1.3.6.1.4.1.9.9.599.1.3.1.1.35ColumncldcClientChannelread-onlycurrentThis object specifies the access point's channel to which the client is associated.
1.3.6.1.4.1.9.9.599.1.3.1.1.36ColumncldcClientAuthModeread-onlycurrentRepresents the Authentication Mode of Client.
1.3.6.1.4.1.9.9.599.1.3.1.1.37ColumncldcClientReasonCoderead-onlycurrentunspecified - Unspecified. previousAuthNotValid - Previous Authentication was not valid. deauthenticationLeaving - Leaving due to deauthentication. disassociat…
1.3.6.1.4.1.9.9.599.1.3.1.1.38ColumncldcClientSessionIDread-onlycurrentThis object indicates the session to which the client is associated.
1.3.6.1.4.1.9.9.599.1.3.1.1.39ColumncldcClientApRoamMacAddressread-onlycurrentThis object indicates the MAC address of the AP to which the client has roamed.
1.3.6.1.4.1.9.9.599.1.3.1.1.40ColumncldcClientMdnsProfileread-onlycurrentThis object specifies the mDNS Profile name this 802.11 wireless client is mapped to. It could be mapped to the WLAN to which the client is connected to, or th…
1.3.6.1.4.1.9.9.599.1.3.1.1.41ColumncldcClientMdnsAdvCountread-onlycurrentThis object specifies the number of mDNS advertisements received on the client.
1.3.6.1.4.1.9.9.599.1.3.1.1.42ColumncldcClientPolicyNameread-onlycurrentThis object indicates the local classification policy to which the client is associated.
1.3.6.1.4.1.9.9.599.1.3.1.1.43ColumncldcClientAAARoleread-onlycurrentThis object indicates the role string of the client that is used as match criterion for local policy profiling. This string is returned during authentication.
1.3.6.1.4.1.9.9.599.1.3.1.1.44ColumncldcClientDeviceTyperead-onlycurrentThis object specifies the device type of the client. This is identified once the profiling operation is completed.
1.3.6.1.4.1.9.9.599.1.3.1.1.45ColumncldcUserAuthTyperead-onlycurrentRepresents the Authentication Type of User.
1.3.6.1.4.1.9.9.599.1.3.2TablecldcClientByIpTablenot-accessiblecurrentThis table represents the 802.11 wireless clients that are associated with the APs that have joined this controller and are indexed by cldcClientByIpAddressTyp…
1.3.6.1.4.1.9.9.599.1.3.2.1RowcldcClientByIpEntrynot-accessiblecurrentEach entry represents a conceptual row in this table and provides the information about the clients associated to the APs that have joined the controller. An e…
1.3.6.1.4.1.9.9.599.1.3.2.1.2ColumncldcClientByIpAddressTypenot-accessiblecurrentThis object represents the type of the Client's address made available through cldcClientByIpAddress.
1.3.6.1.4.1.9.9.599.1.3.2.1.3ColumncldcClientByIpAddressnot-accessiblecurrentThis object represents the inet address of the Client
1.3.6.1.4.1.9.9.599.1.3.2.1.4ColumncldcClientByIpAddressDiscoverTyperead-onlycurrentThis object represents the discovery type of the Client's address invalid(1) = unknown ndp(2) = Address learnt by neighbor discovery protocol dhcp(3) = Address…
1.3.6.1.4.1.9.9.599.1.3.2.1.5ColumncldcClientByIpAddressLastSeenread-onlycurrentThis object indicates timestamp of the time when an address was last seen in REACHABLE state
1.3.6.1.4.1.9.9.599.1.3.3TablecldcSleepingClientTablenot-accessiblecurrentThis table represents the information about Sleeping clients
1.3.6.1.4.1.9.9.599.1.3.3.1RowcldcSleepingClientEntrynot-accessiblecurrentAn entry containing the information about sleeping clients.
1.3.6.1.4.1.9.9.599.1.3.3.1.1ColumncldcSleepingClientMacAddressnot-accessiblecurrentThis object specifies the MAC address of the sleeping client and uniquely identifies the entry.
1.3.6.1.4.1.9.9.599.1.3.3.1.2ColumncldcSleepingClientSsidread-onlycurrentThis object represents the SSID of the WLAN to which the sleeping client is associated.
1.3.6.1.4.1.9.9.599.1.3.3.1.3ColumncldcSleepingClientUserNameread-onlycurrentThis object represents the username used by the sleeping client.
1.3.6.1.4.1.9.9.599.1.3.3.1.4ColumncldcSleepingClientRemainingTimeread-onlycurrentThis object indicates the remaining session time for the sleeping client.
1.3.6.1.4.1.9.9.599.1.3.3.1.5ColumncldcSleepingClientRowStatusread-createcurrentThis is the status column for this row and used to delete specific instances of row in the table.
1.3.6.1.4.1.9.9.599.1.4NodecldcStatisticObjects
1.3.6.1.4.1.9.9.599.1.4.1TablecldcClientStatisticTablenot-accessiblecurrentThis table lists statistics and status of the 802.11 wireless clients associated with the access points attached to the controller.
1.3.6.1.4.1.9.9.599.1.4.1.1RowcldcClientStatisticEntrynot-accessiblecurrentAn entry in this table provides traffic statistics of the associated client based upon its Mac address.
1.3.6.1.4.1.9.9.599.1.4.1.1.1ColumncldcClientDataRetriesread-onlycurrentThis object indicates the number of attempts made by the client before transmitting the MSDU successfully.
1.3.6.1.4.1.9.9.599.1.4.1.1.2ColumncldcClientRtsRetriesread-onlycurrentThis object indicates the number of times the client has attempted to send RTS packets before receiving CTS packets.
1.3.6.1.4.1.9.9.599.1.4.1.1.3ColumncldcClientDuplicatePacketsread-onlycurrentThis object indicates the number of times a duplicate packet is received for the client.
1.3.6.1.4.1.9.9.599.1.4.1.1.4ColumncldcClientDecryptFailuresread-onlycurrentThis object indicates the number of packets received from the client that failed to decrypt properly.
1.3.6.1.4.1.9.9.599.1.4.1.1.5ColumncldcClientMicErrorsread-onlycurrentThis object indicates the number of MIC errors experienced by the client.
1.3.6.1.4.1.9.9.599.1.4.1.1.6ColumncldcClientMicMissingFramesread-onlycurrentThis object indicates the number of missing MIC packets for the client.
1.3.6.1.4.1.9.9.599.1.4.1.1.7ColumncldcClientRaPacketsDroppedread-onlycurrentThis is the number of RA Packets dropped for this client.
1.3.6.1.4.1.9.9.599.1.4.1.1.8ColumncldcClientInterimUpdatesCountread-onlycurrentThis is the number of interim updates count sent for this client.
1.3.6.1.4.1.9.9.599.1.4.1.1.9ColumncldcClientDataBytesReceivedread-onlycurrentThis is the number data bytes received for this mobile station
1.3.6.1.4.1.9.9.599.1.4.1.1.10ColumncldcClientRealtimeBytesReceivedread-onlycurrentThis is the number realtime bytes received for this mobile station
1.3.6.1.4.1.9.9.599.1.4.1.1.11ColumncldcClientRxDataBytesDroppedread-onlycurrentThis is the number Rx data bytes dropped for this mobile station
1.3.6.1.4.1.9.9.599.1.4.1.1.12ColumncldcClientRxRealtimeBytesDroppedread-onlycurrentThis is the number Rx realtime bytes dropped for this mobile station
1.3.6.1.4.1.9.9.599.1.4.1.1.13ColumncldcClientDataBytesSentread-onlycurrentThis is the number data bytes Sent for this mobile station
1.3.6.1.4.1.9.9.599.1.4.1.1.14ColumncldcClientRealtimeBytesSentread-onlycurrentThis is the number realtime bytes Sent for this mobile station
1.3.6.1.4.1.9.9.599.1.4.1.1.15ColumncldcClientTxDataBytesDroppedread-onlycurrentThis is the number Tx data bytes dropped for this mobile station
1.3.6.1.4.1.9.9.599.1.4.1.1.16ColumncldcClientTxRealtimeBytesDroppedread-onlycurrentThis is the number Tx realtime bytes dropped for this mobile station
1.3.6.1.4.1.9.9.599.1.4.1.1.17ColumncldcClientDataPacketsReceivedread-onlycurrentThis is the number data Packets received for this mobile station
1.3.6.1.4.1.9.9.599.1.4.1.1.18ColumncldcClientRealtimePacketsReceivedread-onlycurrentThis is the number realtime Packets received for this mobile station
1.3.6.1.4.1.9.9.599.1.4.1.1.19ColumncldcClientRxDataPacketsDroppedread-onlycurrentThis is the number Rx data Packets dropped for this mobile station
1.3.6.1.4.1.9.9.599.1.4.1.1.20ColumncldcClientRxRealtimePacketsDroppedread-onlycurrentThis is the number Rx realtime Packets dropped for this mobile station
1.3.6.1.4.1.9.9.599.1.4.1.1.21ColumncldcClientDataPacketsSentread-onlycurrentThis is the number data Packets Sent for this mobile station
1.3.6.1.4.1.9.9.599.1.4.1.1.22ColumncldcClientRealtimePacketsSentread-onlycurrentThis is the number realtime Packets Sent for this mobile station
1.3.6.1.4.1.9.9.599.1.4.1.1.23ColumncldcClientTxDataPacketsDroppedread-onlycurrentThis is the number Tx data Packets dropped for this mobile station
1.3.6.1.4.1.9.9.599.1.4.1.1.24ColumncldcClientTxRealtimePacketsDroppedread-onlycurrentThis is the number Tx realtime Packets dropped for this mobile station
1.3.6.1.4.1.9.9.599.1.4.1.1.25ColumncldcClientTxDataPacketsread-onlycurrentThis is the number of data packets sent by this mobile station
1.3.6.1.4.1.9.9.599.1.4.1.1.26ColumncldcClientTxDataBytesread-onlycurrentThis is the number of data bytes sent by this mobile station
1.3.6.1.4.1.9.9.599.1.4.1.1.27ColumncldcClientRxDataPacketsread-onlycurrentThis is the number of data packets sent for this mobile station
1.3.6.1.4.1.9.9.599.1.4.1.1.28ColumncldcClientRxDataBytesread-onlycurrentThis is the number of data bytes sent for this mobile station
1.3.6.1.4.1.9.9.599.2NodeciscoLwappDot11ClientMIBConform
1.3.6.1.4.1.9.9.599.2.1NodeciscoLwappDot11ClientMIBCompliances
1.3.6.1.4.1.9.9.599.2.1.1ComplianceciscoLwappDot11ClientMIBCompliancedeprecatedThe compliance statement for the SNMP entities that implement this MIB.
1.3.6.1.4.1.9.9.599.2.1.2ComplianceciscoLwappDot11ClientMIBComplianceRev2currentThe compliance statement for the SNMP entities that implement this MIB.
1.3.6.1.4.1.9.9.599.2.2NodeciscoLwappDot11ClientMIBGroups
1.3.6.1.4.1.9.9.599.2.2.1GroupciscoLwappDot11ClientMIBConfigGroupcurrentThis collection of objects specifies the required configuration parameters for the 802.11 wireless clients.
1.3.6.1.4.1.9.9.599.2.2.2GroupciscoLwappDot11ClientMIBNotifsGroupcurrentThis collection of objects specifies the notifications for the 802.11 wireless clients.
1.3.6.1.4.1.9.9.599.2.2.3GroupciscoLwappDot11ClientMIBStatusGroupcurrentThis collection of objects specifies the required status parameters for the 802.11 wireless clients.
1.3.6.1.4.1.9.9.599.2.2.4GroupciscoLwappDot11ClientMIBStatusGroupRev2currentThis collection of objects specifies the required status parameters for the 802.11 wireless clients.
1.3.6.1.4.1.9.9.599.2.2.5GroupciscoLwappDot11ClientMIBNotifsGroupRev2currentThis collection of objects represents the notifications for the 802.11 wireless clients.
1.3.6.1.4.1.9.9.599.2.2.6GroupciscoLwappDot11ClientMIBNotifControlGroupcurrentThis collection of objects represents the objects that control the notifications for the 802.11 wireless clients.
1.3.6.1.4.1.9.9.599.3NodeciscoLwappDot11ClientCcxMIBObjects
1.3.6.1.4.1.9.9.599.3.1NodecldcCcxObjects
1.3.6.1.4.1.9.9.599.3.1.1TablecldccCcxVersionInfoTablenot-accessiblecurrentThis table contains the detail of the CCX version supported by the clients. This is used to identify the services supported by a CCX v6 client.
1.3.6.1.4.1.9.9.599.3.1.1.1RowcldccCcxVersionInfoEntrynot-accessiblecurrentThere is an entry in the table for each entry identified by the client mac address.
1.3.6.1.4.1.9.9.599.3.1.1.1.1ColumncldccCcxFoundationServiceVersionread-onlycurrentThis is the CCX version supported by the client for the service, foundation.
1.3.6.1.4.1.9.9.599.3.1.1.1.2ColumncldccCcxLocationServiceVersionread-onlycurrentThis is the CCX version supported by the client for the service, location.
1.3.6.1.4.1.9.9.599.3.1.1.1.3ColumncldccCcxVoiceServiceVersionread-onlycurrentThis is the CCX version supported by the client for the service, voice.
1.3.6.1.4.1.9.9.599.3.1.1.1.4ColumncldccCcxManagementServiceVersionread-onlycurrentThis is the CCX version supported by the client for the service, management.