CISCO-LWAPP-REAP-MIB
195 objects
This MIB is intended to be implemented on all those devices operating as Central Controllers (CC) that terminate the Light Weight Access Point Protocol tunnel from Light-weight LWAPP Access Points. Information represented by this MIB is passed by the controller to those Cisco LWAPP APs, that can operate in stand-alone mode. The relationship between CC and the LWAPP APs can be depicted as follows: +......+ +......+ +......+ +......+ + + + + + + + + + CC + + CC + + CC + + CC + + + + + + + + + +......+ +......+ +......+ +......+ .. . . . .. . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + AP + + AP + + AP + + AP + + AP + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ . . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + MN + + MN + + MN + + MN + + MN + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ The LWAPP tunnel exists between the controller and the APs. The MNs communicate with the APs through the protocol defined by the 802.11 standard. LWAPP APs, upon bootup, discover and join one of the controllers and the controller pushes the configuration, that includes the WLAN parameters, to the LWAPP APs. The APs then encapsulate all the 802.11 frames from wireless clients inside LWAPP frames and forward the LWAPP frames to the controller. GLOSSARY Access Point ( AP ) An entity that contains an 802.11 medium access control ( MAC ) and physical layer ( PHY ) interface and provides access to the distribution services via the wireless medium for associated clients. LWAPP APs encapsulate all the 802.11 frames in LWAPP frames and sends them to the controller to which it is logically connected. Central Controller ( CC ) The central entity that terminates the LWAPP protocol tunnel from the LWAPP APs. Throughout this MIB, this entity is also referred to as 'controller'. Light Weight Access Point Protocol ( LWAPP ) This is a generic protocol that defines the communication between the Access Points and the Central Controller. Mobile Node ( MN ) A roaming 802.11 wireless device in a wireless network associated with an access point. Native VLAN ID A switch port and/or AP can be configured with a 'native VLAN ID'. Untagged or priority-tagged frames are implicitly associated with the native VLAN ID. The default native VLAN ID is '1' if VLAN tagging is enabled. The native VLAN ID is '0' or 'no VLAN ID' if VLAN tagging is not enabled. Remote Edge Access Point ( REAP ) The LWAPP AP that can also act as a stand-alone AP when it loses communication with the controller it was associated with. When REAP can reach the controller (connected state), it gets help from controller to complete client authentication. When a controller is not reachable by REAP, it goes into standalone state and does client authentication by itself. All data packets from clients are either bridged locally (local-switch) or forwarded to the controller (central-switch) depending on the WLAN configuration. Virtual LAN VLAN defined in the IEEE 802.1Q VLAN standard supports logically segmenting of LAN infrastructure into different subnets or workgroups so that packets are switched only between ports within the same VLAN. VLAN ID Each VLAN is identified by a 12-bit 'VLAN ID'. A VLAN ID of '0' is used to indicate 'no VLAN ID'. Valid VLAN IDs range from '1' to '4095'. Home AP A REAP AP can be installed at end-user home. Home AP ethernet port will be connected to DSL or cable modem at home. Home AP will be primed with Controller IP Address so that it will join with controller. REFERENCE [1] Part 11 Wireless LAN Medium Access Control ( MAC ) and Physical Layer ( PHY ) Specifications [2] Draft-obara-capwap-lwapp-00.txt, IETF Light Weight Access Point Protocol
Imported Objects
| CISCO-LWAPP-AP-MIB | cLApSysMacAddress |
| CISCO-LWAPP-WLAN-MIB | -- cLWlanConfigEntry cLWlanIndex |
| CISCO-SMI | ciscoMgmt |
| INET-ADDRESS-MIB | InetAddress InetAddressType |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | MODULE-IDENTITY OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DisplayString RowStatus StorageType TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.9.517 | IdentityciscoLwappReapMIB | This MIB is intended to be implemented on all those devices operating as Central Controllers (CC) that terminate the Light Weight Access Point Protocol tunnel … | ||
| 1.3.6.1.4.1.9.9.517.0 | NodeciscoLwappReapMIBNotifs | |||
| 1.3.6.1.4.1.9.9.517.1 | NodeciscoLwappReapMIBObjects | |||
| 1.3.6.1.4.1.9.9.517.1.1 | NodeciscoLwappReapWlanConfig | |||
| 1.3.6.1.4.1.9.9.517.1.1.1 | TablecLReapWlanConfigTable | not-accessible | current | This table represents the WLAN configuration sent by the controller to REAPs so that the APs can operate in stand-alone mode. LWAPP APs operating in REAP mode … |
| 1.3.6.1.4.1.9.9.517.1.1.1.1 | RowcLReapWlanConfigEntry | not-accessible | current | Each entry represents a conceptual row in cLReapWlanConfigTable and corresponds to the packet switching configuration for a particular WLAN. |
| 1.3.6.1.4.1.9.9.517.1.1.1.1.1 | ColumncLReapWlanEnLocalSwitching | read-write | current | This object indicates the behavior of the REAP when switching the data frames of the clients associated to it through the WLAN identified by cLWlanIndex. A val… |
| 1.3.6.1.4.1.9.9.517.1.1.1.1.2 | ColumncLReapWlanClientIpLearnEnable | read-write | current | This object indicates whether Client IP Address learning is enabled on the controller. When layer two tunneling is employed the IP learning on controller has t… |
| 1.3.6.1.4.1.9.9.517.1.1.1.1.3 | ColumncLReapWlanApAuth | read-write | current | This object indicates the behavior of the REAP, on where to handle the authentication of the client associated to the wlan indicated by cLWlanIndex. A value of… |
| 1.3.6.1.4.1.9.9.517.1.1.1.1.4 | ColumncLReapWlanVlanCentralSwitching | read-write | current | This object specifies whether the AP bridges the traffic centrally. If the VLAN is not configured on the AP uplink, the AP will tunnel the traffic back to the … |
| 1.3.6.1.4.1.9.9.517.1.1.1.1.5 | ColumncLReapWlanDhcpCentral | read-write | current | This object indicates the behavior of the REAP when switching the data frames of the clients associated to it through the WLAN identified by cLWlanIndex. Note … |
| 1.3.6.1.4.1.9.9.517.1.1.1.1.6 | ColumncLReapWlanDhcpOverrideDNS | read-write | current | This object indicates the behavior of the REAP when switching the data frames of the clients associated to it through the WLAN identified by cLWlanIndex. Note … |
| 1.3.6.1.4.1.9.9.517.1.1.1.1.7 | ColumncLReapWlanNatPatEnabled | read-write | current | This object specifies whether Network Address Translation (NAT) and Port Address Trnaslation (PAT) are enabled on this WLAN. This can be enabled only when cLRe… |
| 1.3.6.1.4.1.9.9.517.1.1.1.1.8 | ColumncLReapWlanAssocCentral | read-write | current | This object indicates the behavior of the REAP when handling the (re-)association management frames from the clients through the WLAN identified by cLWlanIndex… |
| 1.3.6.1.4.1.9.9.517.1.2 | NodeciscoLwappReapApConfig | |||
| 1.3.6.1.4.1.9.9.517.1.2.1 | TablecLReapApConfigTable | not-accessible | current | This table represents the VLAN configuration of REAPs. The agent adds a row to this table corresponding to each row representing a REAP in cLApTable of the CIS… |
| 1.3.6.1.4.1.9.9.517.1.2.1.1 | RowcLReapApConfigEntry | not-accessible | current | Each entry represents a conceptual row in cLReapApConfigTable and corresponds to the VLAN configuration of a REAP. |
| 1.3.6.1.4.1.9.9.517.1.2.1.1.1 | ColumncLReapApNativeVlanId | read-write | current | This object defines the Native VLAN ID for the particular AP identified by cLApSysMacAddress. Note that this particular object can be modified through a Set re… |
| 1.3.6.1.4.1.9.9.517.1.2.1.1.2 | ColumncLReapApVlanEnable | read-write | current | This object indicates the availability of Native VLAN configured through cLReapApNativeVlanId on this REAP. A value of 'true' indicates that the VLAN configure… |
| 1.3.6.1.4.1.9.9.517.1.2.1.1.3 | ColumncLReapHomeApEnable | read-write | current | This object represents if this REAP AP is used as Home AP. A value of 'true' indicates that this REAP AP is a Home AP. A value of 'false' indicates that this R… |
| 1.3.6.1.4.1.9.9.517.1.2.1.1.4 | ColumncLReapApLeastLatencyJoinEnable | read-write | current | This object represents if this REAP AP should join controller which has least latency. A value of 'true' indicates that this REAP AP will join controller which… |
| 1.3.6.1.4.1.9.9.517.1.2.1.1.5 | ColumncLReapHomeApLocalSsidReset | read-write | current | This object can be used to reset local SSID on a Home AP. A value of true indicates that the local SSID is to be reset. A value of false on this during set wil… |
| 1.3.6.1.4.1.9.9.517.1.2.1.1.6 | ColumncLReapInstallMappingRadioBackhaul | read-write | current | This object can be used to enable or disable WLANs on backhaul radio. A value of true indicates that wlan mapping would be enabled on backhaul radio. A value o… |
| 1.3.6.1.4.1.9.9.517.1.2.1.1.7 | ColumncLReapApResilientMode | read-write | current | This object can be used to enable or disable Standalone mode support on a REAP AP. A value of true indicates that Standalone mode would be enabled on backhaul … |
| 1.3.6.1.4.1.9.9.517.1.2.2 | TablecLReapApVlanIdTable | not-accessible | current | This table defines the WLAN / VLAN Id mappings to be configured for the REAP identified by cLApSysMacAddress. VLAN Id configured through this table is passed t… |
| 1.3.6.1.4.1.9.9.517.1.2.2.1 | RowcLReapApVlanIdEntry | not-accessible | current | Each entry represents a conceptual row that corresponds to one WLAN / VLAN Id mapping to be applied to the REAP identified by cLApSysMacAddress. |
| 1.3.6.1.4.1.9.9.517.1.2.2.1.1 | ColumncLReapApVlanId | read-create | current | This object represents the VLAN ID to be mapped to the WLAN identified by cLWlanIndex. |
| 1.3.6.1.4.1.9.9.517.1.2.2.1.2 | ColumncLReapApVlanInheritance | read-create | current | This object represents the inheritance to be mapped to the WLAN identified by cLWlanIndex. |
| 1.3.6.1.4.1.9.9.517.1.2.2.1.3 | ColumncLReapApVlanRowStatus | read-create | current | This object represents the rowstatus of the AP level wlan vlan mappings table. |
| 1.3.6.1.4.1.9.9.517.1.2.2.1.4 | ColumncLReapApVlanUsedBySecEthInterface | read-only | current | This object indicates if vlan represented by cLReapApVlanId is used by any of the secondary Ethernet interface when the REAP AP is in Flex+Bridge mode. |
| 1.3.6.1.4.1.9.9.517.1.2.3 | TablecLReapApVlanIdAclTable | not-accessible | current | This table defines the VLAN Id- ACL mappings to be configured for the REAP identified by cLApSysMacAddress. |
| 1.3.6.1.4.1.9.9.517.1.2.3.1 | RowcLReapApVlanIdAclEntry | not-accessible | current | Each entry represents a conceptual row that corresponds to one VLAN Id - ACL mapping to be applied to the REAP identified by cLApSysMacAddress. |
| 1.3.6.1.4.1.9.9.517.1.2.3.1.1 | ColumncLReapVlanId | not-accessible | current | This object specifies the VLAN ID to be mapped to the Acl for the Access Point identified by cLApSysMacAddress. |
| 1.3.6.1.4.1.9.9.517.1.2.3.1.2 | ColumncLReapIngressAcl | read-create | current | This object specifies the name of the ingress Access Control List for the vlan-acl mapping. |
| 1.3.6.1.4.1.9.9.517.1.2.3.1.3 | ColumncLReapEgressAcl | read-create | current | This object specifies the name of the egress Access Control List for the vlan-acl mapping. |
| 1.3.6.1.4.1.9.9.517.1.2.3.1.4 | ColumncLReapApVlanIdAclRowStatus | read-create | current | This object specifies the status column for a conceptual row in this table. |
| 1.3.6.1.4.1.9.9.517.1.2.3.1.5 | ColumncLReapVlanIdAclType | read-only | current | This object specifies the type of the vlan acl mapping apSource - vlan-acl mapping applied from AP level. groupSource - vlan-acl mapping applied from hreap gro… |
| 1.3.6.1.4.1.9.9.517.1.2.4 | TablecLReapApWlanAclTable | not-accessible | current | This table defines the WLAN ACL mappings to be configured for the REAP identified by cLApSysMacAddress. A row is added to this table only if there are WLANs av… |
| 1.3.6.1.4.1.9.9.517.1.2.4.1 | RowcLReapApWlanAclEntry | not-accessible | current | Each entry represents a conceptual row that corresponds to one WLAN / ACL mapping to be applied to the REAP identified by cLApSysMacAddress. |
| 1.3.6.1.4.1.9.9.517.1.2.4.1.1 | ColumncLReapApWebAuthAcl | read-write | current | This object represents the webauth ACL name to be mapped to the WLAN identified by cLWlanIndex. |
| 1.3.6.1.4.1.9.9.517.1.2.4.1.2 | ColumncLReapApWebAuthAclRowStatus | read-create | current | This object represents the status column for a conceptual row in this table. |
| 1.3.6.1.4.1.9.9.517.1.2.5 | TablecLReapWebPolicyAclTable | not-accessible | current | This table represents the web policies associated with an AP. Entries are added or deleted by the user through the use of cLReapWebPolicyRowStatus. |
| 1.3.6.1.4.1.9.9.517.1.2.5.1 | RowcLReapWebPolicyAclEntry | not-accessible | current | Each entry represents a conceptual row in cLReapWebPolicyAclTable. |
| 1.3.6.1.4.1.9.9.517.1.2.5.1.1 | ColumncLReapWebPolicyAcl | not-accessible | current | This object specifies the name of the web policy Access Control List to be mapped to the access point identified by cLApSysMacAddress. |
| 1.3.6.1.4.1.9.9.517.1.2.5.1.2 | ColumncLReapWebPolicyAclRowStatus | read-create | current | This object represents the status column for a conceptual row in this table. |
| 1.3.6.1.4.1.9.9.517.1.2.6 | TablecLReapApLocalSplitACLTable | not-accessible | current | This table defines the WLAN - ACL mappings to be configured for the REAP identified by cLApSysMacAddress. |
| 1.3.6.1.4.1.9.9.517.1.2.6.1 | RowcLReapApLocalSplitACLEntry | not-accessible | current | Each entry represents a conceptual row that corresponds to one WLAN- ACL mapping to be applied to the REAP identified by cLApSysMacAddress. |
| 1.3.6.1.4.1.9.9.517.1.2.6.1.1 | ColumncLReapApLocalSplitAcl | read-create | current | This object represents the LocalSplit ACL name to be mapped to the WLAN identified by cLWlanIndex. |
| 1.3.6.1.4.1.9.9.517.1.2.6.1.2 | ColumncLReapApLocalSplitAclRowStatus | read-create | current | This object represents the status column for a conceptual row in this table. |
| 1.3.6.1.4.1.9.9.517.1.2.7 | TablecLReapApCentralDhcpTable | not-accessible | current | |
| 1.3.6.1.4.1.9.9.517.1.2.7.1 | RowcLReapApCentralDhcpEntry | not-accessible | current | |
| 1.3.6.1.4.1.9.9.517.1.2.7.1.1 | ColumncLReapApDhcpCentral | read-write | current | This object indicates the behavior of the REAP group when switching the data frames of the clients associated to it through the WLAN identified by cLWlanIndex. |
| 1.3.6.1.4.1.9.9.517.1.2.7.1.2 | ColumncLReapApDhcpOverrideDNS | read-write | current | This object indicates the behavior of the REAP group when switching the data frames of the clients associated to it through the WLAN identified by cLWlanIndex. |
| 1.3.6.1.4.1.9.9.517.1.2.7.1.3 | ColumncLReapApNatPatEnabled | read-write | current | This object specifies whether Network Address Translation (NAT) and Port Address Trnaslation (PAT) are enabled on this reap AP. This can be enabled only when c… |
| 1.3.6.1.4.1.9.9.517.1.2.7.1.4 | ColumncLReapApDhcpRowStatus | read-create | current | This object represents the status column for a conceptual row in this table. |
| 1.3.6.1.4.1.9.9.517.1.2.7.1.5 | ColumncLReapApInheritance | read-only | current | This object represents the inheritance level of central DHCP configuration. |
| 1.3.6.1.4.1.9.9.517.1.2.8 | TablecLReapApL2AclTable | not-accessible | current | This table defines the L2 ACL mappings to be configured for the FlexAP identified by cLApSysMacAddress. A row is added to this table only if there are WLANs av… |
| 1.3.6.1.4.1.9.9.517.1.2.8.1 | RowcLReapApL2AclEntry | not-accessible | current | Each entry represents a conceptual row that corresponds to one WLAN / ACL mapping to be applied to the REAP identified by cLApSysMacAddress. |
| 1.3.6.1.4.1.9.9.517.1.2.8.1.1 | ColumncLReapApL2Acl | read-create | current | This object represents the L2ACL name to be mapped to the WLAN identified by cLWlanIndex for this FlexAP |
| 1.3.6.1.4.1.9.9.517.1.2.8.1.2 | ColumncLReapApL2AclRowStatus | read-create | current | This object represents the status column for a conceptual row in this table. |
| 1.3.6.1.4.1.9.9.517.1.3 | NodeciscoLwappReapGroupConfig | |||
| 1.3.6.1.4.1.9.9.517.1.3.1 | TablecLReapGroupConfigTable | not-accessible | current | This table represents the configuration for REAPs so that the APs can be configured as a group. Entries are added or deleted by the user through the use of cLR… |
| 1.3.6.1.4.1.9.9.517.1.3.1.1 | RowcLReapGroupConfigEntry | not-accessible | current | Each entry represents a conceptual row in cLReapGroupConfigTable. |
| 1.3.6.1.4.1.9.9.517.1.3.1.1.1 | ColumncLReapGroupName | not-accessible | current | This object uniquely identifies an entry in cLReapGroupConfigTable. |
| 1.3.6.1.4.1.9.9.517.1.3.1.1.2 | ColumncLReapGroupPrimaryRadiusIndex | read-create | current | The object represents the value that maps to the primary RADIUS server for this group. A value of 0 indicates that the primary RADIUS server is not configured … |
| 1.3.6.1.4.1.9.9.517.1.3.1.1.3 | ColumncLReapGroupSecondaryRadiusIndex | read-create | current | The object represents the value that maps to the secondary RADIUS server for this group. A value of 0 indicates that the primary RADIUS server is not configure… |
| 1.3.6.1.4.1.9.9.517.1.3.1.1.4 | ColumncLReapGroupStorageType | read-create | current | This object represents the storage type for this conceptual row. |
| 1.3.6.1.4.1.9.9.517.1.3.1.1.5 | ColumncLReapGroupRowStatus | read-create | current | This object represents the status column for a conceptual row in this table. |
| 1.3.6.1.4.1.9.9.517.1.3.1.1.6 | ColumncLReapGroupRadiusPacTimeout | read-create | deprecated | This object represents timeout value for the PAC (protected access credentials). Superceded by cLReapGroupRadiusPacTimeoutCtrl. |
| 1.3.6.1.4.1.9.9.517.1.3.1.1.7 | ColumncLReapGroupRadiusAuthorityId | read-create | current | This object configures the authority ID. |
| 1.3.6.1.4.1.9.9.517.1.3.1.1.8 | ColumncLReapGroupRadiusAuthorityInfo | read-create | current | This object represents the authority information. |
| 1.3.6.1.4.1.9.9.517.1.3.1.1.9 | ColumncLReapGroupRadiusServerKey | read-create | current | This object represents the RADIUS server key. For security the key always returns '****'. |
| 1.3.6.1.4.1.9.9.517.1.3.1.1.10 | ColumncLReapGroupRadiusIgnoreKey | read-create | current | This parameter represents whether anonymous provisioning is enabled. A value of 'true' indicates the controller will ignore the key configured in cLReapGroupRa… |
| 1.3.6.1.4.1.9.9.517.1.3.1.1.11 | ColumncLReapGroupRadiusEnable | read-create | current | This parameter represents whether RADIUS is enabled. A value of 'true' indicates that RADIUS is enabled. A value of 'false' indicates that RADIUS is disabled. |
| 1.3.6.1.4.1.9.9.517.1.3.1.1.12 | ColumncLReapGroupRadiusLeapEnable | read-create | current | This parameter represents whether LEAP is enabled. A value of 'true' indicates that LEAP is enabled. A value of 'false' indicates that LEAP is disabled. |
| 1.3.6.1.4.1.9.9.517.1.3.1.1.13 | ColumncLReapGroupRadiusEapFastEnable | read-create | current | This parameter represents whether EAP-FAST is enabled. A value of 'true' indicates that EAP-FAST is enabled. A value of 'false' indicates that EAP-FAST is disa… |
| 1.3.6.1.4.1.9.9.517.1.3.1.1.14 | ColumncLReapGroupRadiusPacTimeoutCtrl | read-create | current | This parameter represents timeout value for the PAC (protected access credentials). Valid range of timeout is 2 to 4095, and value 0 stands for disable. |
| 1.3.6.1.4.1.9.9.517.1.3.1.1.15 | ColumncLReapGroupEfficientApUpgradeEnable | read-write | current | This parameter represents whether Efficient AP image upgrade is enabled. A value of 'true' indicates that Efficient AP image upgrade is enabled. A value of 'fa… |
| 1.3.6.1.4.1.9.9.517.1.3.1.1.16 | ColumncLReapGroupApUpgradeStart | read-write | current | Upgrade start will start the Efficient AP image upgrade for the hreap group with the primary image when it is set to initiatePrimary(1), and from the backup if… |
| 1.3.6.1.4.1.9.9.517.1.3.1.1.17 | ColumncLReapGroupSlaveMaxRetryCount | read-write | current | This object specifies the maximum retries the the slave has to undertake to start the download from the master in the hreap group. |
| 1.3.6.1.4.1.9.9.517.1.3.1.1.18 | ColumncLReapGroupPrimaryRadiusServerType | read-create | current | Server IP Address Type of the primary radius server for the flexconnect group. |
| 1.3.6.1.4.1.9.9.517.1.3.1.1.19 | ColumncLReapGroupPrimaryRadiusServerAddress | read-create | current | Server IP Address of the primary radius server for the flexconnect group. |
| 1.3.6.1.4.1.9.9.517.1.3.1.1.20 | ColumncLReapGroupPrimaryRadiusServerPort | read-create | current | Server IP Address of the primary radius server for the flexconnect group. |
| 1.3.6.1.4.1.9.9.517.1.3.1.1.21 | ColumncLReapGroupPrimaryServerSecret | read-create | current | Secret of the primary radius server for the flexconnect group. |
| 1.3.6.1.4.1.9.9.517.1.3.1.1.22 | ColumncLReapGroupSecRadiusServerType | read-create | current | Server IP Address Type of the secondary radius server for the flexconnect group. |
| 1.3.6.1.4.1.9.9.517.1.3.1.1.23 | ColumncLReapGroupSecRadiusServerAddress | read-create | current | Server IP Address of the secondary radius server for the flexconnect group. |
| 1.3.6.1.4.1.9.9.517.1.3.1.1.24 | ColumncLReapGroupSecRadiusServerPort | read-create | current | Server IP Address of the secondary radius server for the flexconnect group. |
| 1.3.6.1.4.1.9.9.517.1.3.1.1.25 | ColumncLReapGroupSecServerSecret | read-create | current | Secret of the secondary radius server for the flexconnect group. |
| 1.3.6.1.4.1.9.9.517.1.3.1.1.26 | ColumncLReapGroupRadiusPeapEnable | read-create | current | This parameter represents whether PEAP is enabled. A value of 'true' indicates that PEAP is enabled. A value of 'false' indicates that PEAP is disabled. |
| 1.3.6.1.4.1.9.9.517.1.3.1.1.27 | ColumncLReapGroupRadiusEapTlsEnable | read-create | current | This parameter represents whether EAP-TLS is enabled. A value of 'true' indicates that EAP-TLS is enabled. A value of 'false' indicates that EAP-TLS is disable… |
| 1.3.6.1.4.1.9.9.517.1.3.1.1.28 | ColumncLReapGroupCertificateEapTlsEnable | read-create | current | This parameter represents whether certificate for EAP-TLS is enabled. A value of 'true' indicates that EAP-TLS is enabled. A value of 'false' indicates that EA… |
| 1.3.6.1.4.1.9.9.517.1.3.2 | TablecLReapGroupApConfigTable | not-accessible | current | This table represents the group associated with an AP. Entries are added or deleted by the user through the use of cLReapGroupApRowStatus. |
| 1.3.6.1.4.1.9.9.517.1.3.2.1 | RowcLReapGroupApConfigEntry | not-accessible | current | Each entry represents a conceptual row in cLReapGroupApConfigTable. |
| 1.3.6.1.4.1.9.9.517.1.3.2.1.1 | ColumncLReapGroupApStorageType | read-create | current | This object represents the storage type for this conceptual row. |
| 1.3.6.1.4.1.9.9.517.1.3.2.1.2 | ColumncLReapGroupApRowStatus | read-create | current | This object represents the status column for a conceptual row in this table. |
| 1.3.6.1.4.1.9.9.517.1.3.3 | TablecLReapGroupUserConfigTable | not-accessible | current | This table represents the group associated with an User. Entries are added or deleted by the application through the use of cLReapGroupUserRowStatus. |
| 1.3.6.1.4.1.9.9.517.1.3.3.1 | RowcLReapGroupUserConfigEntry | not-accessible | current | Each entry represents a conceptual row in cLReapGroupUserConfigTable. |
| 1.3.6.1.4.1.9.9.517.1.3.3.1.1 | ColumncLReapGroupUserName | not-accessible | current | This object represents the user name for this group. user name is used for authenticating a client associated to an AP within the group. |
| 1.3.6.1.4.1.9.9.517.1.3.3.1.2 | ColumncLReapGroupUserPassword | read-create | current | This object represents the password for this conceptual row. |
| 1.3.6.1.4.1.9.9.517.1.3.3.1.3 | ColumncLReapGroupUserStorageType | read-create | current | This object represents the storage type for this conceptual row. |
| 1.3.6.1.4.1.9.9.517.1.3.3.1.4 | ColumncLReapGroupUserRowStatus | read-create | current | This object represents the status column for a conceptual row in this table. |
| 1.3.6.1.4.1.9.9.517.1.3.4 | TablecLReapGroupVlanAclTable | not-accessible | current | This table represents the configuration of vlan-acl mappings for REAPs. |
| 1.3.6.1.4.1.9.9.517.1.3.4.1 | RowcLReapGroupVlanAclEntry | not-accessible | current | Each entry represents a conceptual row in cLReapGroupVlanAclTable. |
| 1.3.6.1.4.1.9.9.517.1.3.4.1.1 | ColumncLReapGroupVlanId | not-accessible | current | This object represents the VLAN ID to be mapped to the ACL for the reap group identified by cLReapGroupName |
| 1.3.6.1.4.1.9.9.517.1.3.4.1.2 | ColumncLReapGroupIngressAcl | read-create | current | This object specifies the name of the ingress Access Control List for the vlan-acl mapping. |
| 1.3.6.1.4.1.9.9.517.1.3.4.1.3 | ColumncLReapGroupEgressAcl | read-create | current | This object specifies the name of the egress Access Control List for the vlan-acl mapping. |
| 1.3.6.1.4.1.9.9.517.1.3.4.1.4 | ColumncLReapGroupVlanAclRowStatus | read-create | current | This object represents the status column for a conceptual row in this table. |
| 1.3.6.1.4.1.9.9.517.1.3.4.1.5 | ColumncLReapGroupVlanOrder | read-only | current | This object represents the vlan order configuration on the group level. |
| 1.3.6.1.4.1.9.9.517.1.3.5 | TablecLReapGroupAclTable | not-accessible | current | This table represents the configuration of wlan-acl mappings for REAPs. |
| 1.3.6.1.4.1.9.9.517.1.3.5.1 | RowcLReapGroupAclEntry | not-accessible | current | Each entry represents a conceptual row in cLReapGroupAclTable. |
| 1.3.6.1.4.1.9.9.517.1.3.5.1.1 | ColumncLReapGroupWebAuthAcl | read-create | current | This object specifies the name of the webauth Access Control List for the wlan-acl mapping. |
| 1.3.6.1.4.1.9.9.517.1.3.5.1.2 | ColumncLReapGroupAclRowStatus | read-create | current | This object represents the status column for a conceptual row in this table. |
| 1.3.6.1.4.1.9.9.517.1.3.6 | TablecLReapGroupWebPolicyAclTable | not-accessible | current | This table represents the configuration of webpolicy acl mappings for REAP groups. |
| 1.3.6.1.4.1.9.9.517.1.3.6.1 | RowcLReapGroupWebPolicyAclEntry | not-accessible | current | Each entry represents a conceptual row in the cLReapGroupWebPolicyAclTable. |
| 1.3.6.1.4.1.9.9.517.1.3.6.1.1 | ColumncLReapGroupWebPolicyAcl | not-accessible | current | This object specifies the name of the webpolicy Access Control List to be mapped to the REAP group. |
| 1.3.6.1.4.1.9.9.517.1.3.6.1.2 | ColumncLReapGroupWebPolicyAclRowStatus | read-create | current | This object represents the status column for a conceptual row in this table. |
| 1.3.6.1.4.1.9.9.517.1.3.7 | TablecLReapGroupLocalSplitAclTable | not-accessible | current | This table represents the configuration of WLAN-ACL mappings for local split tunneling at REAP groups. |
| 1.3.6.1.4.1.9.9.517.1.3.7.1 | RowcLReapGroupLocalSplitAclEntry | not-accessible | current | Each entry represents a conceptual row in cLReapGroupLocalSplitAclTable. |
| 1.3.6.1.4.1.9.9.517.1.3.7.1.1 | ColumncLReapGroupLocalSplitAcl | read-create | current | This object specifies the name of the LocalSplit Access Control List to be mapped to the WLAN. |
| 1.3.6.1.4.1.9.9.517.1.3.7.1.2 | ColumncLReapGroupLocalSplitAclRowStatus | read-create | current | This object represents the status column for a conceptual row in this table. |
| 1.3.6.1.4.1.9.9.517.1.3.8 | TablecLReapGroupCentralDhcpTable | not-accessible | current | This table represents the configuration of central dhcp processing for REAPs. |
| 1.3.6.1.4.1.9.9.517.1.3.8.1 | RowcLReapGroupCentralDhcpEntry | not-accessible | current | Each entry represents a conceptual row in cLReapGroupCentralDhcpTable. |
| 1.3.6.1.4.1.9.9.517.1.3.8.1.1 | ColumncLReapGroupDhcpCentral | read-write | current | This object indicates the behavior of the REAP group when switching the data frames of the clients associated to it through the WLAN identified by cLWlanIndex. |
| 1.3.6.1.4.1.9.9.517.1.3.8.1.2 | ColumncLReapGroupDhcpOverrideDNS | read-write | current | This object indicates the behavior of the REAP group when switching the data frames of the clients associated to it through the WLAN identified by cLWlanIndex. |
| 1.3.6.1.4.1.9.9.517.1.3.8.1.3 | ColumncLReapGroupNatPatEnabled | read-write | current | This object specifies whether Network Address Translation (NAT) and Port Address Trnaslation (PAT) are enabled on this reap group. This can be enabled only whe… |
| 1.3.6.1.4.1.9.9.517.1.3.8.1.4 | ColumncLReapGroupDhcpRowStatus | read-create | current | This object represents the status column for a conceptual row in this table. |
| 1.3.6.1.4.1.9.9.517.1.3.9 | TablecLReapGroupVlanIdTable | not-accessible | current | This table defines the WLAN / VLAN Id mappings to be configured for the REAP identified by REAP group name. VLAN Id configured through this table is passed to … |
| 1.3.6.1.4.1.9.9.517.1.3.9.1 | RowcLReapGroupVlanIdEntry | not-accessible | current | Each entry represents a conceptual row that corresponds to one WLAN / VLAN Id mapping to be applied to the REAP identified by cLReapGroupName. |
| 1.3.6.1.4.1.9.9.517.1.3.9.1.1 | ColumncLReapGroupWlanVlanId | read-create | current | This object represents the VLAN ID to be mapped to the WLAN identified by cLWlanIndex. |
| 1.3.6.1.4.1.9.9.517.1.3.9.1.2 | ColumncLReapGroupVlanRowStatus | read-create | current | This object represents the reap group vlan mapping row status. |
| 1.3.6.1.4.1.9.9.517.1.4 | NodeciscoLwappReapAclConfig | |||
| 1.3.6.1.4.1.9.9.517.1.4.1 | TablecLReapAclTable | not-accessible | current | The table listing hreap ACLs (Access Control Lists) on the Switch. |
| 1.3.6.1.4.1.9.9.517.1.4.1.1 | RowcLReapAclEntry | not-accessible | current | Each entry represents the attributes for clReapAclTable. An entry gets added to the table on creating a flexconnect ACL. |
| 1.3.6.1.4.1.9.9.517.1.4.1.1.1 | ColumncLReapAclName | read-create | current | This object specifies name of the Access Control List. |
| 1.3.6.1.4.1.9.9.517.1.4.1.1.2 | ColumncLReapAclApplyMode | read-only | current | This object specifies the apply mode of the ACL on the switch. Mode value 'applied' means the ACL has been applied on the switch. |
| 1.3.6.1.4.1.9.9.517.1.4.1.1.3 | ColumncLReapAclRowStatus | read-create | current | This object specifies the row Status of the ACL. |
| 1.3.6.1.4.1.9.9.517.1.4.2 | TablecLReapAclRuleTable | not-accessible | current | The table listing Acl Rules(Access Control List Entries) on the ACL with name cLReapAclName. |
| 1.3.6.1.4.1.9.9.517.1.4.2.1 | RowcLReapAclRuleEntry | not-accessible | current | Each entry represents the attributes for clReapAclRuleTable. An entry gets added to the table on creating a rule on flexconnect ACL. |
| 1.3.6.1.4.1.9.9.517.1.4.2.1.1 | ColumncLReapAclRuleIndex | read-create | current | Index of the ACL rule. This can be updated to reset the sequence of the rules of an ACL. |
| 1.3.6.1.4.1.9.9.517.1.4.2.1.2 | ColumncLReapAclRuleAction | read-create | current | The permission mode of a rule. |
| 1.3.6.1.4.1.9.9.517.1.4.2.1.3 | ColumncLReapAclRuleSourceIpAddressType | read-create | current | Source IP Address Type of the ACL rule. The value is limited to ipv4 only. |
| 1.3.6.1.4.1.9.9.517.1.4.2.1.4 | ColumncLReapAclRuleSourceIpAddress | read-create | current | Source IP Address of the ACL rule. es any source address. |
| 1.3.6.1.4.1.9.9.517.1.4.2.1.5 | ColumncLReapAclRuleSourceIpNetmaskType | read-create | current | Source IP Netmask type of the ACL rule. The value is limited to ipv4 only. |
| 1.3.6.1.4.1.9.9.517.1.4.2.1.6 | ColumncLReapAclRuleSourceIpNetmask | read-create | current | Source IP Netmask of the ACL rule. A value 0 implies any source mask. |
| 1.3.6.1.4.1.9.9.517.1.4.2.1.7 | ColumncLReapAclRuleDestinationIpAddressType | read-create | current | Destination IP Address type of the ACL rule. The value is limited to ipv4 only. |
| 1.3.6.1.4.1.9.9.517.1.4.2.1.8 | ColumncLReapAclRuleDestinationIpAddress | read-create | current | Destination IP Address of the ACL rule. A value 0 implies any destination address. |
| 1.3.6.1.4.1.9.9.517.1.4.2.1.9 | ColumncLReapAclRuleDestinationIpNetmaskType | read-create | current | Destination Netmask type of the ACL rule. The value is limited to ipv4 only. |
| 1.3.6.1.4.1.9.9.517.1.4.2.1.10 | ColumncLReapAclRuleDestinationIpNetmask | read-create | current | Destination Netmask of the ACL rule. A value 0 implies any destination mask. |
| 1.3.6.1.4.1.9.9.517.1.4.2.1.11 | ColumncLReapAclRuleProtocol | read-create | current | Protocol of the packet. It can be either of the pre specified protocols like TCP, UDP, ICMP, ESP, AH, GRE, IP, Ethernet Over IP, OSPF or any number between 0 a… |
| 1.3.6.1.4.1.9.9.517.1.4.2.1.12 | ColumncLReapAclRuleStartSourcePort | read-create | current | Source Port of the packet. It can be either of the pre specified ports like HTTP, HTTPS, Telnet, RADIUS etc or any number between 0 and 65535. A value 65536 im… |
| 1.3.6.1.4.1.9.9.517.1.4.2.1.13 | ColumncLReapAclRuleEndSourcePort | read-create | current | Source Port of the packet. It can be either of the pre specified ports like HTTP, HTTPS, Telnet, RADIUS etc or any number between 0 and 65535. A value 65536 im… |
| 1.3.6.1.4.1.9.9.517.1.4.2.1.14 | ColumncLReapAclRuleStartDestinationPort | read-create | current | Destination Port of the packet. It can be either of the pre specified ports like HTTP, HTTPS, Telnet, RADIUS etc or any number between 0 and 65535. A value 655… |
| 1.3.6.1.4.1.9.9.517.1.4.2.1.15 | ColumncLReapAclRuleEndDestinationPort | read-create | current | Destination Port of the packet. It can be either of the pre specified ports like HTTP, HTTPS, Telnet, RADIUS etc or any number between 0 and 65535. A value 655… |
| 1.3.6.1.4.1.9.9.517.1.4.2.1.16 | ColumncLReapAclRuleDscp | read-create | current | DSCP value of the rule. A value 256 implies Any |
| 1.3.6.1.4.1.9.9.517.1.4.2.1.17 | ColumncLReapAclNewRuleIndex | read-create | current | New Index of the ACL rule. This attribute should be updated if the requirement is to reset the sequence of the rules of an ACL. A read on this will not yield a… |
| 1.3.6.1.4.1.9.9.517.1.4.2.1.18 | ColumncLReapAclRuleRowStatus | read-create | current | Row Status of the ACL Rule. |
| 1.3.6.1.4.1.9.9.517.1.4.3 | TablecLReapL2AclTable | not-accessible | current | The table listing Layer2 ACLs (Access Control Lists) on the Switch. |
| 1.3.6.1.4.1.9.9.517.1.4.3.1 | RowcLReapL2AclEntry | not-accessible | current | Each entry represents the attributes for cLReapL2AclTable. An entry gets added to the table on creating a Layer2 ACL. |
| 1.3.6.1.4.1.9.9.517.1.4.3.1.1 | ColumncLReapL2AclName | not-accessible | current | This object specifies name of the L2 Access Control List. |
| 1.3.6.1.4.1.9.9.517.1.4.3.1.2 | ColumncLReapL2AclApplyMode | read-only | current | This object specifies the apply mode of the L2ACL on the switch. Mode value 'applied' means the L2ACL has been applied on the switch. Default mode on creation … |
| 1.3.6.1.4.1.9.9.517.1.4.3.1.3 | ColumncLReapL2AclRowStatus | read-create | current | This object specifies the row Status of the L2ACL. |
| 1.3.6.1.4.1.9.9.517.1.4.4 | TablecLReapL2AclRuleTable | not-accessible | current | The table listing L2Acl Rules(Access Control List Entries) on the L2ACL with name cLReapL2AclName. |
| 1.3.6.1.4.1.9.9.517.1.4.4.1 | RowcLReapL2AclRuleEntry | not-accessible | current | Each entry represents the attributes for clReapL2AclRuleTable. An entry gets added to the table on creating a rule on L2ACL. |
| 1.3.6.1.4.1.9.9.517.1.4.4.1.1 | ColumncLReapL2AclRuleIndex | not-accessible | current | This object represents the unique index of the L2ACL rule. This can be updated to reset the sequence of the rules of an L2ACL. |
| 1.3.6.1.4.1.9.9.517.1.4.4.1.2 | ColumncLReapL2AclRuleAction | read-create | current | This object specifies the permission mode of a rule. |
| 1.3.6.1.4.1.9.9.517.1.4.4.1.3 | ColumncLReapL2AclRuleEthertype | read-create | current | This object represents the etherType of the L2Acl rule. Default is 0x0 |
| 1.3.6.1.4.1.9.9.517.1.4.4.1.4 | ColumncLReapL2AclRuleEthertypeMask | read-create | current | This object represents the etherType Mask of the L2Acl rule. Default is 0x0 |
| 1.3.6.1.4.1.9.9.517.1.4.4.1.5 | ColumncLReapL2AclRuleDirection | read-create | current | This object specifies the direction of the packet to which the rule may be applied. |
| 1.3.6.1.4.1.9.9.517.1.4.4.1.6 | ColumncLReapL2AclNewRuleIndex | read-create | current | This object specifies the new Index of the L2ACL rule. This attribute should be updated if the requirement is to reset the sequence of the rules of an ACL. A r… |
| 1.3.6.1.4.1.9.9.517.1.4.4.1.7 | ColumncLReapL2AclRuleRowStatus | read-create | current | This object specifies the status of a conceptual row in the ACL Rule Table. This is used to create and delete entries in the table. |
| 1.3.6.1.4.1.9.9.517.1.5 | NodeciscoLwappReapMasterApConfig | |||
| 1.3.6.1.4.1.9.9.517.1.5.1 | TablecLReapMasterApConfigTable | not-accessible | current | This table represents the master AP admin configuration of REAPs. The agent adds a row to this table corresponding to each row representing a REAP in cLApTable… |
| 1.3.6.1.4.1.9.9.517.1.5.1.1 | RowcLReapMasterApConfigEntry | not-accessible | current | Each entry represents a conceptual row in cLReapMasterApConfigTable and corresponds to the Master configuration of a REAP. |
| 1.3.6.1.4.1.9.9.517.1.5.1.1.1 | ColumncLReapMasterApModel | read-only | current | The object specifies the model of the AP in the hreap group. |
| 1.3.6.1.4.1.9.9.517.1.5.1.1.2 | ColumncLReapMasterApManual | read-only | current | This object represents if this REAP AP is manually configured by the user. A value of 'true' indicates that this REAP master is manually configured. A value of… |
| 1.3.6.1.4.1.9.9.517.1.5.1.1.3 | ColumncLReapMasterApRowStatus | read-create | current | This object specifies the row Status of the Master table. |
| 1.3.6.1.4.1.9.9.517.1.6 | NodeciscoLwappReapGlobalConfig | |||
| 1.3.6.1.4.1.9.9.517.1.6.1 | ScalarcLReapArpCaheEnabled | read-write | current | This object specifies whether ARP cache feature is enabled for the flexconnect Access Points connected to the Wireless LAN Controller. |
| 1.3.6.1.4.1.9.9.517.2 | NodeciscoLwappReapMIBConform | |||
| 1.3.6.1.4.1.9.9.517.2.1 | NodeciscoLwappReapMIBCompliances | |||
| 1.3.6.1.4.1.9.9.517.2.1.1 | ComplianceciscoLwappReapMIBCompliance | deprecated | The compliance statement for the SNMP entities that implement the ciscoLwappReapMIB module. | |
| 1.3.6.1.4.1.9.9.517.2.1.2 | ComplianceciscoLwappReapMIBComplianceRev1 | deprecated | The compliance statement for the SNMP entities that implement the ciscoLwappReapMIB module. | |
| 1.3.6.1.4.1.9.9.517.2.1.3 | ComplianceciscoLwappReapMIBComplianceRev2 | deprecated | The compliance statement for the SNMP entities that implement the ciscoLwappReapMIB module. | |
| 1.3.6.1.4.1.9.9.517.2.1.4 | ComplianceciscoLwappReapMIBComplianceRev3 | deprecated | The compliance statement for the SNMP entities that implement the ciscoLwappReapMIB module. | |
| 1.3.6.1.4.1.9.9.517.2.1.5 | ComplianceciscoLwappReapMIBComplianceRev4 | deprecated | The compliance statement for the SNMP entities that implement the ciscoLwappReapMIB module. | |
| 1.3.6.1.4.1.9.9.517.2.1.6 | ComplianceciscoLwappReapMIBComplianceRev5 | current | The compliance statement for the SNMP entities that implement the ciscoLwappReapMIB module. | |
| 1.3.6.1.4.1.9.9.517.2.2 | NodeciscoLwappReapMIBGroups | |||
| 1.3.6.1.4.1.9.9.517.2.2.1 | GroupciscoLwappReapWlanConfigGroup | current | This collection of objects represent the WLAN configuration to be passed to the REAP. | |
| 1.3.6.1.4.1.9.9.517.2.2.2 | GroupciscoLwappReapApConfigGroup | current | This collection of objects represent the information needed by the REAP AP to locally switch the client data packets. The collection also includes the VLAN con… | |
| 1.3.6.1.4.1.9.9.517.2.2.3 | GroupciscoLwappReapGroupConfigGroup | current | This collection of objects represent the information needed by the REAP APs to configure REAP groups. | |
| 1.3.6.1.4.1.9.9.517.2.2.4 | GroupciscoLwappReapGroupConfigRadiusGroup | deprecated | This collection of objects represent the RADIUS information needed by the REAP APs in a REAP group. | |
| 1.3.6.1.4.1.9.9.517.2.2.5 | GroupciscoLwappReapGroupConfigUserAuthGroup | current | This collection of objects represent the information needed for user authentication. | |
| 1.3.6.1.4.1.9.9.517.2.2.6 | GroupciscoLwappReapApConfigGroupHomeAp | current | This supplemental collection of objects represents objects related to Home AP configuration for REAP AP. | |
| 1.3.6.1.4.1.9.9.517.2.2.7 | GroupciscoLwappReapGroupConfigRadiusGroup1 | current | This collection of objects represent the RADIUS information needed by the REAP APs in a REAP group. | |
| 1.3.6.1.4.1.9.9.517.2.2.8 | GroupciscoLwappReapWlanConfigGroupSup1 | current | This collection of objects represent additional WLAN configuration to be passed to the REAP. |