CISCO-OPTICAL-OTS-MIB
153 objects
This MIB module defines the managed objects and statistics objects for physical layer characteristics of optical line systems and optical transport devices. Performance monitoring (PM) parameters are used to gather, store, set thresholds for and report performance data for early detection of problems. Thresholds are used to set error levels for each PM parameter. During the accumulation cycle, if the current value of a performance monitoring parameter reaches or exceeds its corresponding threshold value, a threshold crossing alarm (TCA) is generated. The TCAs provide early detection of performance degradation. Glossary: OTS : Optical Transmission Section OTS-OCH : Optical Channel Information on OTS ATTN : Optical Attenuation GAIN : Optical Amplifier Gain TILT : Optical Amplifier TILT LBC : Laser Bias Current OSRI : Optical Safety Remote Interlock TX : Transmit RX : Receive VOA : Variable Optical Attenuator dB : Decibel dBm : Decibel-milliwatt mW : Milliwatt nm : Nanometer.
Imported Objects
| CISCO-OPTICAL-MIB | CoiIntervalType CoiOptAlarmServiceAffecting CoiOptAlarmSeverity CoiOptAlarmStatus CoiOptAlarmType CoiOpticalPower CoiOpticalWavelength |
| CISCO-SMI | ciscoMgmt |
| IF-MIB | ifIndex ifName |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | TEXTUAL-CONVENTION TimeStamp TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.9.834 | IdentityciscoOpticalOtsMIB | This MIB module defines the managed objects and statistics objects for physical layer characteristics of optical line systems and optical transport devices. Pe… | ||
| 1.3.6.1.4.1.9.9.834.0 | NodeciscoOpticalOtsMIBNotifs | |||
| 1.3.6.1.4.1.9.9.834.0.1 | NotificationcooOtsStatusChange | current | This notification is generated when the value of cooOtsControllerStatus changes. The varbind for this notification indicates the ifindex, ifname of the OTS int… | |
| 1.3.6.1.4.1.9.9.834.0.2 | NotificationcooOtsOchStatusChange | current | This notification is generated when the value of cooOtsOchControllerStatus changes. The varbind for this notification indicates the ifindex, ifname of the OTS-… | |
| 1.3.6.1.4.1.9.9.834.0.3 | NotificationcooOtsEquipmentAlarm | current | This notification is generated whenever the optical equipment alarm is generated. | |
| 1.3.6.1.4.1.9.9.834.1 | NodeciscoOpticalOtsMIBObjects | |||
| 1.3.6.1.4.1.9.9.834.1.1 | NodecooOtsController | |||
| 1.3.6.1.4.1.9.9.834.1.1.1 | ScalarcooOtsNotifEnabled | read-write | current | This object controls the generation of cooOtsStatusChange notification. If the value of this object is 'true', then the generation of cooOtsStatusChange notifi… |
| 1.3.6.1.4.1.9.9.834.1.1.2 | TablecooOtsControllerTable | not-accessible | current | This table provides management information for OTS optical layer related attributes of interfaces with an ifType of opticalTransport(196). |
| 1.3.6.1.4.1.9.9.834.1.1.2.1 | RowcooOtsControllerEntry | not-accessible | current | An entry containing management information on OTS optical layer related attributes of interfaces with an ifType opticalTrasnport(196). Entries are created by t… |
| 1.3.6.1.4.1.9.9.834.1.1.2.1.1 | ColumncooOtsControllerPortType | read-only | current | This object represents the port type of the optical OTS interface. |
| 1.3.6.1.4.1.9.9.834.1.1.2.1.2 | ColumncooOtsControllerLaserStatus | read-only | current | This object represents the current operational state of the laser. |
| 1.3.6.1.4.1.9.9.834.1.1.2.1.3 | ColumncooOtsControllerRXPower | read-only | current | This object represents the receive power in 1/100 dBm on optical OTS interfaces. |
| 1.3.6.1.4.1.9.9.834.1.1.2.1.4 | ColumncooOtsControllerTXPower | read-only | current | This object represents the transmit power in 1/100 dBm on optical OTS interfaces. |
| 1.3.6.1.4.1.9.9.834.1.1.2.1.5 | ColumncooOtsControllerAmpliGain | read-write | current | This object represents the amplifier gain value in 1/100 dB on optical OTS interfaces. |
| 1.3.6.1.4.1.9.9.834.1.1.2.1.6 | ColumncooOtsControllerAmpliTilt | read-write | current | This object represents the amplifier tilt value in 1/100 dB on optical OTS interfaces. |
| 1.3.6.1.4.1.9.9.834.1.1.2.1.7 | ColumncooOtsControllerTotalRXPower | read-only | current | This object is used to represents the total receive power in 1/100 dBm on optical OTS interfaces. |
| 1.3.6.1.4.1.9.9.834.1.1.2.1.8 | ColumncooOtsControllerTotalTXPower | read-only | current | This object is used to represents the total transmit power in 1/100 dBm on optical OTS interfaces. |
| 1.3.6.1.4.1.9.9.834.1.1.2.1.9 | ColumncooOtsControllerRXVoaAttenuation | read-write | current | This object represents the receive VOA attenuation value in 1/100 dBm on optical OTS interfaces. |
| 1.3.6.1.4.1.9.9.834.1.1.2.1.10 | ColumncooOtsControllerTXVoaAttenuation | read-write | current | This object represents the transmit VOA attenuation value in 1/100 dBm on optical OTS interfaces. |
| 1.3.6.1.4.1.9.9.834.1.1.2.1.11 | ColumncooOtsControllerRXLowThreshold | read-write | current | This object is used to configure the receive low threshold in 1/100 dBm on optical OTS interfaces. |
| 1.3.6.1.4.1.9.9.834.1.1.2.1.12 | ColumncooOtsControllerTXLowThreshold | read-write | current | This object is used to configure the transmit low threshold in 1/100 dBm on optical OTS interfaces. |
| 1.3.6.1.4.1.9.9.834.1.1.2.1.13 | ColumncooOtsControllerAmpliChannelPwr | read-write | current | This object is used to configure the amplifier channel power in 1/100 dBm on optical OTS interfaces. |
| 1.3.6.1.4.1.9.9.834.1.1.2.1.14 | ColumncooOtsControllerChannelPwrMaxDelta | read-write | current | This object is used to configure the maximum delta on channel power in 1/100 dBm on optical OTS interfaces. |
| 1.3.6.1.4.1.9.9.834.1.1.2.1.15 | ColumncooOtsControllerAmpliControlMode | read-write | current | This object is used to configure the amplifier control mode. |
| 1.3.6.1.4.1.9.9.834.1.1.2.1.16 | ColumncooOtsControllerAmpliGainRange | read-write | current | This object is used to configure the amplifier gain range. |
| 1.3.6.1.4.1.9.9.834.1.1.2.1.17 | ColumncooOtsControllerAmpliSafetyCtrlMode | read-write | current | This object is used to configure the safety control mode. |
| 1.3.6.1.4.1.9.9.834.1.1.2.1.18 | ColumncooOtsControllerOsri | read-write | current | This object is used to configure the OSRI. |
| 1.3.6.1.4.1.9.9.834.1.1.2.1.19 | ColumncooOtsControllerProtectionPortRole | read-only | current | This object represents the port role on optical channel interfaces. |
| 1.3.6.1.4.1.9.9.834.1.1.2.1.20 | ColumncooOtsControllerState | read-only | current | This object represents the controller status of optical OTS interfaces. |
| 1.3.6.1.4.1.9.9.834.1.1.2.1.21 | ColumncooOtsControllerTranspAdminState | read-only | current | This object represents the transport administration status on optical OTS interfaces. |
| 1.3.6.1.4.1.9.9.834.1.1.2.1.22 | ColumncooOtsControllerAlarmState | read-only | current | This object indicates the current alarms status of the Optics layer. Alarms description : noDefect : No alarms highRXPwr : Input optical power reading over the… |
| 1.3.6.1.4.1.9.9.834.1.1.2.1.23 | ColumncooOtsControllerRXSpanLoss | read-only | current | This object is used to represents the sapn loss power in 1/100 dBm on optical OTS interfaces |
| 1.3.6.1.4.1.9.9.834.1.1.2.1.24 | ColumncooOtsControllerTXSpanLoss | read-only | current | This object is used to represents the sapn loss power in 1/100 dBm on optical OTS interfaces |
| 1.3.6.1.4.1.9.9.834.1.1.2.1.25 | ColumncooOtsControllerRXEnabled | read-write | current | This object represents the RX direction status of optical OTS interfaces. |
| 1.3.6.1.4.1.9.9.834.1.1.2.1.26 | ColumncooOtsControllerTXEnabled | read-write | current | This object represents the TX direction status of optical OTS interfaces. |
| 1.3.6.1.4.1.9.9.834.1.1.3 | TablecooOtsOchControllerTable | not-accessible | current | This table provides management information for OTS-OCH optical layer related attributes of interfaces with an ifType of opticalTransport(196). |
| 1.3.6.1.4.1.9.9.834.1.1.3.1 | RowcooOtsOchControllerEntry | not-accessible | current | An entry containing management information on OTS-OCH optical layer related attributes of interfaces with an ifType opticalTransport(196). Entries are created … |
| 1.3.6.1.4.1.9.9.834.1.1.3.1.1 | ColumncooOtsOchControllerPortType | read-only | current | This object represents the port type of the optical OTS-OCH interface. |
| 1.3.6.1.4.1.9.9.834.1.1.3.1.2 | ColumncooOtsOchControllerLaserStatus | read-only | current | This object represents the current operational state of the laser. |
| 1.3.6.1.4.1.9.9.834.1.1.3.1.3 | ColumncooOtsOchControllerRXPower | read-only | current | This object represents the receive power in 1/100 dBm on optical OTS-OCH interfaces. |
| 1.3.6.1.4.1.9.9.834.1.1.3.1.4 | ColumncooOtsOchControllerTXPower | read-only | current | This object represents the transmit power in 1/100 dBm on optical OTS-OCH interfaces. |
| 1.3.6.1.4.1.9.9.834.1.1.3.1.5 | ColumncooOtsOchControllerRXLowThreshold | read-write | current | This object is used to configure the receive low threshold in 1/100 dBm on optical OTS-OCH interfaces. |
| 1.3.6.1.4.1.9.9.834.1.1.3.1.6 | ColumncooOtsOchControllerTXLowThreshold | read-write | current | This object is used to configure the transmit low threshold in 1/100 dBm on optical OTS-OCH interfaces. |
| 1.3.6.1.4.1.9.9.834.1.1.3.1.7 | ColumncooOtsOchControllerWavelength | read-only | current | This object represents the wavelength on optical OTS-OCH interfaces (unit 1/100 nm). |
| 1.3.6.1.4.1.9.9.834.1.1.3.1.8 | ColumncooOtsOchControllerFrequency | read-only | current | This object represents the frequency on optical Ots-Och channel interfaces (unit 100 MHz). |
| 1.3.6.1.4.1.9.9.834.1.1.3.1.9 | ColumncooOtsOchControllerChannelNumber | read-only | current | This object represents the channel number on optical OTS-OCH interfaces. |
| 1.3.6.1.4.1.9.9.834.1.1.3.1.10 | ColumncooOtsOchControllerState | read-only | current | This object represents the controller status of optical OTS-OCH interfaces. |
| 1.3.6.1.4.1.9.9.834.1.1.3.1.11 | ColumncooOtsOchControllerTranspAdminState | read-only | current | This object represents the transport administration status on optical OTS-OCH interfaces. |
| 1.3.6.1.4.1.9.9.834.1.1.3.1.12 | ColumncooOtsOchControllerAlarmState | read-only | current | This object indicates the current alarms status of the Optics layer. Alarms description : noDefect : No alarms highRXPwr : Input optical power reading over the… |
| 1.3.6.1.4.1.9.9.834.1.1.3.1.13 | ColumncooOtsOchControllerWidth | read-only | current | This object represents the frequency on optical Ots-Och channel interfaces (unit 1/10 GHz). |
| 1.3.6.1.4.1.9.9.834.1.1.4 | ScalarcooOtsOchNotifEnabled | read-write | current | This object controls the generation of cooOtsOchStatusChange notification. If the value of this object is 'true', then the generation of cooOtsOchStatusChange … |
| 1.3.6.1.4.1.9.9.834.1.2 | NodecooOtsPerformanceMonitoring | |||
| 1.3.6.1.4.1.9.9.834.1.2.1 | TablecooOtsThresholdTable | not-accessible | current | This table provides threshold information for optical layer related attributes of interfaces with an ifType of opticalTransport(196) and interval type as cooTh… |
| 1.3.6.1.4.1.9.9.834.1.2.1.1 | RowcooOtsThresholdEntry | not-accessible | current | An entry containing threshold information on optical layer related attributes of interfaces with an ifType opticalTransport(196). Entries are created by the fe… |
| 1.3.6.1.4.1.9.9.834.1.2.1.1.1 | ColumncooThreshIntervalType | not-accessible | current | This object represents the interval type during which the performance statistics are accumulated for the interface. |
| 1.3.6.1.4.1.9.9.834.1.2.1.1.2 | ColumncooThreshTXPowerMin | read-write | current | This object is used to configure the threshold of minimum transmit power for the interface in 1/100 dBm. |
| 1.3.6.1.4.1.9.9.834.1.2.1.1.3 | ColumncooThreshRXPowerMin | read-write | current | This object is used to configure the threshold of minimum receive power for the interface in 1/100 dBm. |
| 1.3.6.1.4.1.9.9.834.1.2.1.1.4 | ColumncooThreshLBCMin | read-only | current | This object is used to configure the threshold of minimum laser bias current in 1/10 percent. |
| 1.3.6.1.4.1.9.9.834.1.2.1.1.5 | ColumncooThreshTXPowerMax | read-write | current | This object is used to configure the threshold of maximum Transmit power for the interface in 1/100 dBm. |
| 1.3.6.1.4.1.9.9.834.1.2.1.1.6 | ColumncooThreshRXPowerMax | read-write | current | This object is used to configure the threshold of maximum receive power for the interface in 1/100 dBm. |
| 1.3.6.1.4.1.9.9.834.1.2.1.1.7 | ColumncooThreshLBCMax | read-only | current | This object is used to configure the threshold of maximum Laser Bias Current in 1/10 percent for the interface. |
| 1.3.6.1.4.1.9.9.834.1.2.1.1.8 | ColumncooThreshTXPowerEnableMin | read-write | current | This object is used to configure the enablement of threshold minimum transmit power for the interface. |
| 1.3.6.1.4.1.9.9.834.1.2.1.1.9 | ColumncooThreshRXPowerEnableMin | read-write | current | This object is used to configure the enablement of the threshold minimum receive power for the interface. |
| 1.3.6.1.4.1.9.9.834.1.2.1.1.10 | ColumncooThreshLBCEnableMin | read-write | current | This object is used to configure the enablement of the threshold minimum laser bias current for the interface. |
| 1.3.6.1.4.1.9.9.834.1.2.1.1.11 | ColumncooThreshTXPowerEnableMax | read-write | current | This object is used to configure the enablement of the threshold maximum transmit power for the interface. |
| 1.3.6.1.4.1.9.9.834.1.2.1.1.12 | ColumncooThreshRXPowerEnableMax | read-write | current | This object is used to configure the enablement of the threshold maximum receive power for the interface. |
| 1.3.6.1.4.1.9.9.834.1.2.1.1.13 | ColumncooThreshLBCEnableMax | read-write | current | This object is used to configure the enablement of the threshold maximum laser bias current for the interface. |
| 1.3.6.1.4.1.9.9.834.1.2.1.1.14 | ColumncooThreshAmpliGainMin | read-write | current | This object is used to configure the threshold of minimum ampli gain for the interface in 1/100 dB. |
| 1.3.6.1.4.1.9.9.834.1.2.1.1.15 | ColumncooThreshAmpliGainMax | read-write | current | This object is used to configure the threshold of maximum ampli gain for the interface in 1/100 dB. |
| 1.3.6.1.4.1.9.9.834.1.2.1.1.16 | ColumncooThreshAmpliGainEnableMax | read-write | current | This object is used to configure the enablement of the threshold maximum ampli gain for the interface. |
| 1.3.6.1.4.1.9.9.834.1.2.1.1.17 | ColumncooThreshAmpliGainEnableMin | read-write | current | This object is used to configure the enablement of the threshold minimum ampli gain for the interface. |
| 1.3.6.1.4.1.9.9.834.1.2.1.1.18 | ColumncooThreshAmpliGainTiltMin | read-write | current | This object is used to configure the threshold of minimum ampli gain tilt for the interface in 1/100 dB. |
| 1.3.6.1.4.1.9.9.834.1.2.1.1.19 | ColumncooThreshAmpliGainTiltMax | read-write | current | This object is used to configure the threshold of maximum ampli gain tilt for the interface in 1/100 dB. |
| 1.3.6.1.4.1.9.9.834.1.2.1.1.20 | ColumncooThreshAmpliGainTiltEnableMax | read-write | current | This object is used to configure the enablement of the threshold maximum ampli gain tilt for the interface. |
| 1.3.6.1.4.1.9.9.834.1.2.1.1.21 | ColumncooThreshAmpliGainTiltEnableMin | read-write | current | This object is used to configure the enablement of the threshold minimum ampli gain tilt for the interface. |
| 1.3.6.1.4.1.9.9.834.1.2.2 | TablecooOtsCurrentTable | not-accessible | current | This table provides current information for optical layer related attributes of interfaces with an ifType of opticalChannel(196), lane as cooCurrentLane and in… |
| 1.3.6.1.4.1.9.9.834.1.2.2.1 | RowcooOtsCurrentEntry | not-accessible | current | An entry containing current information on optical layer related attributes of interfaces with an ifType opticalChannel(196). Entries are created by the featur… |
| 1.3.6.1.4.1.9.9.834.1.2.2.1.1 | ColumncooCurrentIntervalType | not-accessible | current | This object represents the interval type during which the current performance statistics are accumulated. |
| 1.3.6.1.4.1.9.9.834.1.2.2.1.2 | ColumncooCurrentTXPowerMax | read-only | current | This object specifies the current maximum transmit power for the interface in 1/100 dBm. |
| 1.3.6.1.4.1.9.9.834.1.2.2.1.3 | ColumncooCurrentRXPowerMax | read-only | current | This object specifies the current maximum receive power for the interface in 1/100 dBm. |
| 1.3.6.1.4.1.9.9.834.1.2.2.1.4 | ColumncooCurrentLBCMax | read-only | current | This object specifies the current maximum laser bias current in 1/10 percent for the interface. |
| 1.3.6.1.4.1.9.9.834.1.2.2.1.5 | ColumncooCurrentTXPowerMin | read-only | current | This object specifies the current minimum transmit power for the interface in 1/100 dBm. |
| 1.3.6.1.4.1.9.9.834.1.2.2.1.6 | ColumncooCurrentRXPowerMin | read-only | current | This object specifies the current minimum receive power for the interface in 1/100 dBm. |
| 1.3.6.1.4.1.9.9.834.1.2.2.1.7 | ColumncooCurrentLBCMin | read-only | current | This object specifies the current minimum laser bias current in 1/10 percent for the interface. |
| 1.3.6.1.4.1.9.9.834.1.2.2.1.8 | ColumncooCurrentTXPowerAvg | read-only | current | This object specifies the current average transmit power for the interface in 1/100 dBm. |
| 1.3.6.1.4.1.9.9.834.1.2.2.1.9 | ColumncooCurrentRXPowerAvg | read-only | current | This object specifies the current average receive power for the interface in 1/100 dBm. |
| 1.3.6.1.4.1.9.9.834.1.2.2.1.10 | ColumncooCurrentLBCAvg | read-only | current | This object specifies the current average Laser Bias Current in 1/10 percent for the interface. |
| 1.3.6.1.4.1.9.9.834.1.2.2.1.11 | ColumncooCurrentTimestamp | read-only | current | This object specifies the timestamp for the current bucket for the interface. |
| 1.3.6.1.4.1.9.9.834.1.2.2.1.12 | ColumncooCurrentAmpliGainMin | read-only | current | This object specifies the current minimum amplifier gain for the interface in 1/100 dB. |
| 1.3.6.1.4.1.9.9.834.1.2.2.1.13 | ColumncooCurrentAmpliGainMax | read-only | current | This object specifies the current maximum amplifier gain for the interface in 1/100 dB. |
| 1.3.6.1.4.1.9.9.834.1.2.2.1.14 | ColumncooCurrentAmpliGainAvg | read-only | current | This object specifies the current average amplifier gain for the interface in 1/100 dB. |
| 1.3.6.1.4.1.9.9.834.1.2.2.1.15 | ColumncooCurrentAmpliGainTiltMin | read-only | current | This object specifies the current minimum amplifier gain tilt for the interface in 1/100 dB. |
| 1.3.6.1.4.1.9.9.834.1.2.2.1.16 | ColumncooCurrentAmpliGainTiltMax | read-only | current | This object specifies the current maximum amplifier gain tilt for the interface in 1/100 dB. |
| 1.3.6.1.4.1.9.9.834.1.2.2.1.17 | ColumncooCurrentAmpliGainTiltAvg | read-only | current | This object specifies the current average amplifier gain tilt for the interface in 1/100 dB. |
| 1.3.6.1.4.1.9.9.834.1.2.3 | TablecooOtsIntervalTable | not-accessible | current | This table provides interval information for optical layer related attributes of interfaces with an ifType of opticalChannel(196), lane as cooIntervalLane, Int… |
| 1.3.6.1.4.1.9.9.834.1.2.3.1 | RowcooOtsIntervalEntry | not-accessible | current | An entry containing interval information on optical layer related attributes of interfaces with an ifType opticalChannel(196). Entries are created by the featu… |
| 1.3.6.1.4.1.9.9.834.1.2.3.1.1 | ColumncooIntervalType | not-accessible | current | This object represents the interval type during which the performance statistics are accumulated. |
| 1.3.6.1.4.1.9.9.834.1.2.3.1.2 | ColumncooIntervalNum | not-accessible | current | This object identifies the interval for which the set of interval performance values is available. The interval identified by 1 is the most recent 15 minute or… |
| 1.3.6.1.4.1.9.9.834.1.2.3.1.3 | ColumncooIntervalTXPowerMax | read-only | current | This object specifies the interval maximum transmit power in 1/100 dBm for the interface. |
| 1.3.6.1.4.1.9.9.834.1.2.3.1.4 | ColumncooIntervalRXPowerMax | read-only | current | This object specifies the interval maximum receive power in 1/100 dBm for the interface. |
| 1.3.6.1.4.1.9.9.834.1.2.3.1.5 | ColumncooIntervalLBCMax | read-only | current | This object specifies the interval maximum laser bias current in 1/10 percent for the interface. |
| 1.3.6.1.4.1.9.9.834.1.2.3.1.6 | ColumncooIntervalTXPowerMin | read-only | current | This object specifies the interval minimum transmit power in 1/100 dBm for the interface. |
| 1.3.6.1.4.1.9.9.834.1.2.3.1.7 | ColumncooIntervalRXPowerMin | read-only | current | This object specifies the interval minimum receive power in 1/100 dBm for the interface. |
| 1.3.6.1.4.1.9.9.834.1.2.3.1.8 | ColumncooIntervalLBCMin | read-only | current | This object specifies the interval minimum laser bias current in 1/10 percent for the interface. |
| 1.3.6.1.4.1.9.9.834.1.2.3.1.9 | ColumncooIntervalTXPowerAvg | read-only | current | This object specifies the interval average transmit power in 1/100 dBm for the interface. |
| 1.3.6.1.4.1.9.9.834.1.2.3.1.10 | ColumncooIntervalRXPowerAvg | read-only | current | This object specifies the interval average receive power in 1/100 dBm for the interface. |
| 1.3.6.1.4.1.9.9.834.1.2.3.1.11 | ColumncooIntervalLBCAvg | read-only | current | This object specifies the interval average laser bias current in 1/10 percent for the interface. |
| 1.3.6.1.4.1.9.9.834.1.2.3.1.12 | ColumncooIntervalTimestamp | read-only | current | This object specifies the timestamp, for the bucket specified by 'cooIntervalNum', for the interface. |
| 1.3.6.1.4.1.9.9.834.1.2.3.1.13 | ColumncooIntervalAmpliGainMin | read-only | current | This object specifies the interval minimum amplifier gain in 1/100 dB for the interface. |
| 1.3.6.1.4.1.9.9.834.1.2.3.1.14 | ColumncooIntervalAmpliGainMax | read-only | current | This object specifies the interval maximum amplifier gain in 1/100 dB for the interface. |
| 1.3.6.1.4.1.9.9.834.1.2.3.1.15 | ColumncooIntervalAmpliGainAvg | read-only | current | This object specifies the interval acerage amplifier gain in 1/100 dB for the interface. |
| 1.3.6.1.4.1.9.9.834.1.2.3.1.16 | ColumncooIntervalAmpliGainTiltMin | read-only | current | This object specifies the interval minimum amplifier gain tilt in 1/100 dB for the interface. |
| 1.3.6.1.4.1.9.9.834.1.2.3.1.17 | ColumncooIntervalAmpliGainTiltMax | read-only | current | This object specifies the interval maximum amplifier gain tilt in 1/100 dB for the interface. |
| 1.3.6.1.4.1.9.9.834.1.2.3.1.18 | ColumncooIntervalAmpliGainTiltAvg | read-only | current | This object specifies the interval average amplifier gain tilt in 1/100 dB for the interface. |
| 1.3.6.1.4.1.9.9.834.1.5 | NodecooOtsEquipmentAlarmGroup | |||
| 1.3.6.1.4.1.9.9.834.1.5.1 | ScalarcooOtsAlarmLocation | accessible-for-notify | current | This object indicates the location of the component that raised alarm, within the device. |
| 1.3.6.1.4.1.9.9.834.1.5.2 | ScalarcooOtsAlarmType | accessible-for-notify | current | This object indicates the type of alarm that is raised. |
| 1.3.6.1.4.1.9.9.834.1.5.3 | ScalarcooOtsAlarmTimeStamp | accessible-for-notify | current | This object represents the time when an event occurred. This is accurate only upto a second. |
| 1.3.6.1.4.1.9.9.834.1.5.4 | ScalarcooOtsAlarmName | accessible-for-notify | current | This object represents the user-visible name, which uniquely identifies the alarm in the system. |
| 1.3.6.1.4.1.9.9.834.1.5.5 | ScalarcooOtsAlarmAdditionalInfo | accessible-for-notify | current | This object provides additional information about the alarm. This object would be an empty string if no additional information is specified. |
| 1.3.6.1.4.1.9.9.834.1.5.6 | ScalarcooOtsAlarmSeverity | accessible-for-notify | current | This object specifies alarm severity. |
| 1.3.6.1.4.1.9.9.834.1.5.7 | ScalarcooOtsAlarmStatus | accessible-for-notify | current | This object specifies alarm status. |
| 1.3.6.1.4.1.9.9.834.1.5.8 | ScalarcooOtsAlarmServiceAffecting | accessible-for-notify | current | This object specifies the service affecting state of the alarm. |
| 1.3.6.1.4.1.9.9.834.2 | NodeciscoOpticalOtsMIBConformance | |||
| 1.3.6.1.4.1.9.9.834.2.1 | NodeciscoOpticalOtsMIBCompliances | |||
| 1.3.6.1.4.1.9.9.834.2.1.1 | ComplianceciscoOpticalOtsMIBCompliance | current | The compliance statement for platforms that monitor the parameters for the optical interfaces. | |
| 1.3.6.1.4.1.9.9.834.2.2 | NodeciscoOpticalOtsMIBGroups | |||
| 1.3.6.1.4.1.9.9.834.2.2.1 | GroupcooOtsGroup | current | The collection of objects to provide information related to the optical OTS characteristics for interfaces of ifType opticalChannel(196). | |
| 1.3.6.1.4.1.9.9.834.2.2.2 | GroupcooOtsOchGroup | current | The collection of objects to give information related to the optical OTS-OCH characteristics for interfaces of ifType opticalChannel(196). | |
| 1.3.6.1.4.1.9.9.834.2.2.3 | GroupcooOtsControllerGroup | current | The collection of objects to allow configurations and give information related to the optical OTS characteristics for interfaces of ifType opticalChannel(196). | |
| 1.3.6.1.4.1.9.9.834.2.2.4 | GroupcooOtsOchControllerGroup | current | The collection of objects to allow configurations and give information related to the optical OTS-OCH characteristics for interfaces of ifType opticalChannel(1… | |
| 1.3.6.1.4.1.9.9.834.2.2.5 | GroupcooOtsThresholdGroup | current | The collection of objects used for monitoring the threshold information for optical layer related attributes of interfaces with an ifType of opticalChannel(196… | |
| 1.3.6.1.4.1.9.9.834.2.2.6 | GroupcooOtsCurrentGroup | current | The collection of objects used for monitoring the current information for optical layer related attributes of interfaces with an ifType of opticalChannel(196) … | |
| 1.3.6.1.4.1.9.9.834.2.2.7 | GroupcooOtsIntervalGroup | current | The collection of objects used for monitoring the interval information for optical layer related attributes of interfaces with an ifType of opticalChannel(196)… | |
| 1.3.6.1.4.1.9.9.834.2.2.8 | GroupcooOtsNotifEnableGroup | current | The collection of objects to enable the notification generations upon an interface's alarms status change on optics OTS layer. | |
| 1.3.6.1.4.1.9.9.834.2.2.9 | GroupcooOtsNotifGroup | current | The optical status change notifications whenever the alarms status of optical OTS layer on an interface changes. | |
| 1.3.6.1.4.1.9.9.834.2.2.10 | GroupcooOtsOchNotifGroup | current | The optical status change notifications whenever the alarms status of optical OTS-OCH layer on an interface changes. | |
| 1.3.6.1.4.1.9.9.834.2.2.11 | GroupcooOtsEquipmentAlarmInfoGroup | current | The optical equipment notifications whenever the alarm is generated. | |
| 1.3.6.1.4.1.9.9.834.2.2.12 | GroupcooOtsPowerGroup | current | The collection of objects used for monitoring the total power information for optical layer related attributes of interfaces with an ifType of opticalChannel(1… | |
| 1.3.6.1.4.1.9.9.834.2.2.13 | GroupcooOtsOchNotifEnableGroup | current | The collection of objects to enable the notification generations upon an interface's alarms status change on optics OTS-OCH layer. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| CiscoOpticalOtsAmpliControlMode | INTEGER { manual(1), auto(2) } | current | OTS ports associated to amplifier device, this value indicates how the amplifier is controlled. Valid values are - manual(1) : manual control mode (An external entity has to provide gain/tilt settings) auto(2) : automat… |
| CiscoOpticalOtsAmpliGainRange | INTEGER { normal(1), extended(2) } | current | OTS ports associated to amplifier device, this value indicates the working ranges available for amplifier gain. Valid values are - normal(1) : normal gain range extended(2) : extended gain range |
| CiscoOpticalOtsAmpliSafetyCtrlMode | INTEGER { auto(1), disabled(2) } | current | OTS ports associated to amplifier device, this value indicates how the safety compliaces regulation are statisfied. Valid values are - auto(1) : automatic safety control mode disabled(2) : disabled safety control mode |
| CiscoOpticalOtsGainInDb | Integer32 (-100..4000) | current | OTS ports associated to amplifier device,this value represent the amplifier gain setting. An integer value that represents the gain level in 1/100ths of dB. A negative value represents not meaninful value in case the am… |
| CiscoOpticalOtsLaserStatus | INTEGER { unknown(1), on(2), off(3), apr(4) } | current | This value indicates the module laser status. Valid values are - unknown(1) : unknown status on(2) : laser on off(3) : laser off apr(4) : Denotes Automatic Power Reduction (APR) |
| CiscoOpticalOtsOsri | INTEGER { on(1), off(2) } | current | OTS ports associated to amplifier device, this value indicates the optical safety remote interlock (OSRI) status. Valid values are - on(1) : force laser shutdown for safety interlock off(2) : normal operation |
| CiscoOpticalOtsPortType | INTEGER { line(1), com(2), osc(3), comCheck(4), working(5), protected(6) } | current | This value indicates the port type for optical OTS interface. Valid values are - line(1) : port facing the fiber and far-end section. com(2) : port facing the near-end section. osc(3) : port for optical service channel … |
| CiscoOpticalOtsProtectionPortRole | INTEGER { active(1), standby(2) } | current | This value indicates the actual OTS port role in case a protection device is in place. Valid values are - active(1) : active port standby(2) : standby port |
| CiscoOpticalOtsState | INTEGER { up(1), down(2), adminDown(3) } | current | This value indicates the controller status. Valid values are - up(1) : controller operstatus up down(2) : controller operstatus down adminDown(3) : controller administratively down |
| CiscoOpticalOtsTiltInDb | Integer32 (-500..500) | current | OTS ports associated to amplifier device, this values represent the tilt parameter. An integer value that represents the tilt level in 1/100ths of dB. Example: The value 300 represents a tilt level of 3.0 dB. |
| CiscoOpticalOtsTranspAdminState | INTEGER { inService(1), outOfService(2), maintenance(3), ains(4) } | current | This value indicates the transport administrative status. Valid values are - inService(1) : transport administrative status in-service outOfService(2) : transport administrative status out-of-service maintenance(3) : tr… |
| CiscoOpticalOtsVoaAttenInDb | Unsigned32 | current | An unsigned integer value that represents the VOA attenuation level in 1/100ths of dB. Example: The value 200 represents an attenuation level of 2.0 dB. |