CISCO-PPPOE-MIB
71 objects
Cisco PPPoE sessions management MIB Module.
Imported Objects
| ATM-MIB | atmVclEntry atmVclVci atmVclVpi |
| ATM-TC-MIB | AtmVcIdentifier AtmVpIdentifier |
| CISCO-QOS-PIB-MIB | Percent |
| CISCO-SMI | ciscoMgmt |
| IF-MIB | ifDescr ifIndex |
| Q-BRIDGE-MIB | VlanId VlanIndex |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Gauge32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | MacAddress TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.9.194 | IdentityciscoPppoeMIB | Cisco PPPoE sessions management MIB Module. | ||
| 1.3.6.1.4.1.9.9.194.1 | NodeciscoPppoeMIBObjects | |||
| 1.3.6.1.4.1.9.9.194.1.1 | NodecPppoeSystemSessionInfo | |||
| 1.3.6.1.4.1.9.9.194.1.1.1 | ScalarcPppoeSystemCurrSessions | read-only | current | The current number of active PPPoE sessions within this system. |
| 1.3.6.1.4.1.9.9.194.1.1.2 | ScalarcPppoeSystemHighWaterSessions | read-only | current | The high water mark of the established PPPoE sessions since the system was initialized. |
| 1.3.6.1.4.1.9.9.194.1.1.3 | ScalarcPppoeSystemMaxAllowedSessions | read-write | current | Maximum number of allowed PPPoE sessions within the system. |
| 1.3.6.1.4.1.9.9.194.1.1.4 | ScalarcPppoeSystemThresholdSessions | read-write | current | Threshold value of the established PPPoE sessions within the system. Default value is equal to cPppoeSystemMaxSessionsConfigurable |
| 1.3.6.1.4.1.9.9.194.1.1.5 | ScalarcPppoeSystemExceededSessionErrors | read-only | current | The accumulated number of errors for establishing PPPoE session in the system due to the cPppoeSystemCurrSessions value exceeds the cPppoeSystemMaxAllowedSessi… |
| 1.3.6.1.4.1.9.9.194.1.1.6 | ScalarcPppoeSystemPerMacSessionlimit | read-write | current | This object provides limit on number of PPPoE sessions for a single client Ethernet MAC address. If the limit is reached new session request from the client wo… |
| 1.3.6.1.4.1.9.9.194.1.1.7 | ScalarcPppoeSystemPerMacIWFSessionlimit | read-write | current | This object provides limit on number of PPPoE sessions with interworking flag(IWF) enabled, from a single client MAC address. If the limit is reached new sessi… |
| 1.3.6.1.4.1.9.9.194.1.1.8 | ScalarcPppoeSystemPerMacThrottleRatelimit | read-write | current | This object provides the rate limit at which PPPoE session were created from a single client MAC address. During a configured time interval, once the number of… |
| 1.3.6.1.4.1.9.9.194.1.1.9 | ScalarcPppoeSystemPerVLANlimit | read-write | current | This object provides limit on number of PPPoE sessions on a particular Vlan. If the limit is reached new session request on this vlan would be denied. |
| 1.3.6.1.4.1.9.9.194.1.1.10 | ScalarcPppoeSystemPerVLANthrottleRatelimit | read-write | current | This object provides the rate limit at which PPPoE session were created on a Vlan. During a configured time interval once the number of new session requests co… |
| 1.3.6.1.4.1.9.9.194.1.1.11 | ScalarcPppoeSystemPerVClimit | read-write | current | This object provides limit on number of PPPoE sessions on a particular ATM-VC. If the limit is reached new session request on this VC would be denied. |
| 1.3.6.1.4.1.9.9.194.1.1.12 | ScalarcPppoeSystemPerVCThrottleRatelimit | read-write | current | This object provides the rate limit at which PPPoE session were created on an ATM-VC. During a configured time interval, once the number of new session request… |
| 1.3.6.1.4.1.9.9.194.1.1.13 | ScalarcPppoeSystemSessionLossThreshold | read-write | current | This object is used to monitor number of active PPPoE sessions above a healthy watermark. If number of PPPoE sessions falls below this watermark then we can ex… |
| 1.3.6.1.4.1.9.9.194.1.1.14 | ScalarcPppoeSystemSessionLossPercent | read-write | current | This object is used to monitor the percentage of PPPoE sessions going down at a configured time interval. During a time interval if percentage of PPPoE session… |
| 1.3.6.1.4.1.9.9.194.1.2 | NodecPppoeVcCfgInfo | |||
| 1.3.6.1.4.1.9.9.194.1.2.1 | TablecPppoeVcCfgTable | not-accessible | current | The table contains the PPPoE protocol related configuration for the VCLs(ATM Interface Virtual Channel Link). |
| 1.3.6.1.4.1.9.9.194.1.2.1.1 | RowcPppoeVcCfgEntry | not-accessible | current | An entry containing additional PPPoE protocol configuration related management information applicable to a particular VCL. |
| 1.3.6.1.4.1.9.9.194.1.2.1.1.1 | ColumncPppoeVcEnable | read-write | current | This object specifies whether the PPPoE protocol should be enabled for this VCL. If the value of this object is `false`, PPPoE protocol is disabled; otherwise … |
| 1.3.6.1.4.1.9.9.194.1.3 | NodecPppoeVcSessionsInfo | |||
| 1.3.6.1.4.1.9.9.194.1.3.1 | TablecPppoeVcSessionsTable | not-accessible | current | Table of configuration and statistics about the number of PPPoE sessions on a list of VCLs(ATM Interface Virtual Channel Link). |
| 1.3.6.1.4.1.9.9.194.1.3.1.1 | RowcPppoeVcSessionsEntry | not-accessible | current | An entry in the table containing PPPoE session related information on a VCL. The entry of this table is created when the value of cPppoeVcEnable object is set … |
| 1.3.6.1.4.1.9.9.194.1.3.1.1.1 | ColumncPppoeVcCurrSessions | read-only | current | The current number of active PPPoE sessions on the VCL. |
| 1.3.6.1.4.1.9.9.194.1.3.1.1.2 | ColumncPppoeVcHighWaterSessions | read-only | current | The high water mark of the established PPPoE sessions on the VCL. |
| 1.3.6.1.4.1.9.9.194.1.3.1.1.3 | ColumncPppoeVcMaxAllowedSessions | read-write | current | The maximum number of allowed PPPoE sessions on the VCL. |
| 1.3.6.1.4.1.9.9.194.1.3.1.1.4 | ColumncPppoeVcThresholdSessions | read-write | current | The Threshold value of the established PPPoE sessions on the VCL. Default value is equal to cPppoeVcMaxAllowedSessions. |
| 1.3.6.1.4.1.9.9.194.1.3.1.1.5 | ColumncPppoeVcExceededSessionErrors | read-only | current | The accumulated number of errors for establishing PPPoE session in the VC due to the cPppoeVcCurrSessions value exceeds the cPppoeVcMaxAllowedSessions value. |
| 1.3.6.1.4.1.9.9.194.1.4 | NodecPppoeSessionsPerInterfaceInfo | |||
| 1.3.6.1.4.1.9.9.194.1.4.1 | TablecPppoeSessionsPerInterfaceTable | not-accessible | current | A list of interfaces' PPPoE session information. |
| 1.3.6.1.4.1.9.9.194.1.4.1.1 | RowcPppoeSessionsPerInterfaceEntry | not-accessible | current | An entry in the table containing PPPoE sessions information such as count information of various states like PPP Termination Aggregation(PTA), Forwarded(FWDED)… |
| 1.3.6.1.4.1.9.9.194.1.4.1.1.1 | ColumncPppoeTotalSessions | read-only | current | The total number of PPPoE sessions which includes PPP Termination Aggregation(PTA), Forwarded(FWDED) and Transient(TRANS) state on a physical interface. |
| 1.3.6.1.4.1.9.9.194.1.4.1.1.2 | ColumncPppoePtaSessions | read-only | current | Number of PPPoE sessions which are in PPP Termination Aggregation(PTA) state on a particular physical interface. |
| 1.3.6.1.4.1.9.9.194.1.4.1.1.3 | ColumncPppoeFwdedSessions | read-only | current | Number of PPPoE sessions which are in Forwarded(FWDED) state on a particular physical interface. |
| 1.3.6.1.4.1.9.9.194.1.4.1.1.4 | ColumncPppoeTransSessions | read-only | current | Number of PPPoE sessions which are in Transient(TRANS) state on a particular physical interface. |
| 1.3.6.1.4.1.9.9.194.1.4.1.1.5 | ColumncPppoePerInterfaceSessionLossThreshold | read-only | current | This object is used to monitor number of active PPPoE sessions, initiated from a particular physical interface. The sssion count is accumulation of all the ppp… |
| 1.3.6.1.4.1.9.9.194.1.4.1.1.6 | ColumncPppoePerInterfaceSessionLossPercent | read-only | current | This object is used to monitor the percentage of PPPoE sessions loss on a particular physical interface including all of its sub-interfaces. If during a config… |
| 1.3.6.1.4.1.9.9.194.1.5 | NodecPppoeSystemSessionNotifyObjects | |||
| 1.3.6.1.4.1.9.9.194.1.5.1 | ScalarcPppoeSystemSessionClientMacAddress | accessible-for-notify | current | The client MAC address that is referred as a part of the notification information. Example: cPppoeSystemSessionPerMACLimitNotif |
| 1.3.6.1.4.1.9.9.194.1.5.2 | ScalarcPppoeSystemSessionVlanID | accessible-for-notify | current | The Vlan ID of PPPoE session that is referred as a part of the notification information. Example: cPppoeSystemSessionPerVLANLimitNotif |
| 1.3.6.1.4.1.9.9.194.1.5.3 | ScalarcPppoeSystemSessionInnerVlanID | accessible-for-notify | current | The inner Vlan ID of PPPoE QinQ session that is referred as a part of the notification information. Example: cPppoeSystemSessionPerVLANLimitNotif |
| 1.3.6.1.4.1.9.9.194.1.5.4 | ScalarcPppoeSystemSessionVci | accessible-for-notify | current | The ATM VCI of PPPoE session that is referred as a part of the notification information. Example:cPppoeSystemSessionPerVCLimitTrap |
| 1.3.6.1.4.1.9.9.194.1.5.5 | ScalarcPppoeSystemSessionVpi | accessible-for-notify | current | The ATM VPI of PPPoE session that is referred as a part of the notification information. Example: cPppoeSystemSessionPerVCLimitTrap |
| 1.3.6.1.4.1.9.9.194.2 | NodeciscoPppoeMIBNotificationPrefix | |||
| 1.3.6.1.4.1.9.9.194.2.0 | NodeciscoPppoeMIBNotification | |||
| 1.3.6.1.4.1.9.9.194.2.0.1 | NotificationcPppoeSystemSessionThresholdTrap | current | A notification indicating that number of active sessions on the system exceeded system sessions threshold value. System sessions threshold value is indicated b… | |
| 1.3.6.1.4.1.9.9.194.2.0.2 | NotificationcPppoeVcSessionThresholdTrap | current | A notification indicating that number of active sessions on the VC exceeded vc sessions threshold value. VC sessions threshold value is indicated by cPppoeVcTh… | |
| 1.3.6.1.4.1.9.9.194.2.0.3 | NotificationcPppoeSystemSessionPerMACLimitNotif | current | A notification indicating that number of active session from a particular client Ethernet MAC address has reached the configured per MAC limit. There won't be … | |
| 1.3.6.1.4.1.9.9.194.2.0.4 | NotificationcPppoeSystemSessionPerMACThrottleNotif | current | A notification indicating that the number of new PPPoE session requests coming in over a configured time interval, from a particular client Ethernet MAC addres… | |
| 1.3.6.1.4.1.9.9.194.2.0.5 | NotificationcPppoeSystemSessionPerVLANLimitNotif | current | A notification indicating that number of active session on a Vlan has reached the maximum limit. There won't be any new PPPoE session possible on this Vlan. Th… | |
| 1.3.6.1.4.1.9.9.194.2.0.6 | NotificationcPppoeSystemSessionPerVLANThrottleNotif | current | A notification indicating that the number of new PPPoE session request coming on a particular Vlan, over a configured time interval has reached rate limit. The… | |
| 1.3.6.1.4.1.9.9.194.2.0.7 | NotificationcPppoeSystemSessionPerVCLimitNotif | current | A notification indicating that number of active sessions for a ATM VCI/VPI has crossed the configured maximum limit. No more session would be possible on this … | |
| 1.3.6.1.4.1.9.9.194.2.0.8 | NotificationcPppoeSystemSessionPerVCThrottleNotif | current | A notification indicating that the number of new PPPoE session request coming on a particular ATM VC, over a configured time interval has reached rate limit. T… | |
| 1.3.6.1.4.1.9.9.194.2.0.9 | NotificationcPppoeSystemSessionLossThresholdNotif | current | A notification indicating that number of PPPoE session count dropped below configured global threshold watermark. There will be only one trap send whenever cou… | |
| 1.3.6.1.4.1.9.9.194.2.0.10 | NotificationcPppoePerInterfaceSessionLossThresholdNotif | current | A notification indicating that number of PPPoE session initiated via a particular interface has dropped below the configured value for that interface. The inte… | |
| 1.3.6.1.4.1.9.9.194.2.0.11 | NotificationcPppoeSystemSessionLossPercentNotif | current | A notification indicating that percentage of PPPoE session lost globally over a duration of time has crossed the configured threshold. The configured percentag… | |
| 1.3.6.1.4.1.9.9.194.2.0.12 | NotificationcPppoePerInterfaceSessionLossPercentNotif | current | A notification indicating that percentage of PPPoE sessions lost has crossed configured threshold value for a particular interface. The interface details can b… | |
| 1.3.6.1.4.1.9.9.194.3 | NodeciscoPppoeMIBConformance | |||
| 1.3.6.1.4.1.9.9.194.3.1 | NodeciscoPppoeMIBCompliances | |||
| 1.3.6.1.4.1.9.9.194.3.1.1 | ComplianceciscoPppoeMIBBasicCompliance | deprecated | The compliance statement for entities which implement the Cisco Basic PPPoE MIB. | |
| 1.3.6.1.4.1.9.9.194.3.1.2 | ComplianceciscoPppoeMIBBasicComplianceRev1 | read-only | current | The compliance statement for entities which implement the Cisco Basic PPPoE MIB. |
| 1.3.6.1.4.1.9.9.194.3.2 | NodeciscoPppoeMIBGroups | |||
| 1.3.6.1.4.1.9.9.194.3.2.1 | GroupcPppoeSystemGroup | current | A collection of objects providing information about the PPPoE sessions on a system. | |
| 1.3.6.1.4.1.9.9.194.3.2.2 | GroupcPppoeVcCfgGroup | current | A collection of objects specifying PPPoE protocol related configuration on the VCL. | |
| 1.3.6.1.4.1.9.9.194.3.2.3 | GroupcPppoeVcSessionsGroup | current | A collection of objects providing information about the number of sessions on the VCL. | |
| 1.3.6.1.4.1.9.9.194.3.2.4 | GroupcPppoeNotificationsGroup | current | The collection of notifications used to indicate high PPPoE session volume information(e.g, the number of current PPPoE sessions exceeds threshold setting for … | |
| 1.3.6.1.4.1.9.9.194.3.2.5 | GroupcPppoePerInterfaceGroup | current | A collection of objects providing PPPoE per-interface session state counts and configured threshold informations. | |
| 1.3.6.1.4.1.9.9.194.3.2.6 | GroupcPppoeSystemLimitsThresholdsGroup | current | A collection of objects providing the session limit or throttling configuration. There are various Limitation we can impose on PPPoE Sessions it may be limit b… | |
| 1.3.6.1.4.1.9.9.194.3.2.7 | GroupcPppoeSystemLimitsThresholdsNotifObjectsGroup | current | This group is collection of notify objects which are used to carry notify information along with certain traps which implements Session restriction such as lim… | |
| 1.3.6.1.4.1.9.9.194.3.2.8 | GroupcPppoeSystemLimitsThresholdsNotifGroup | current | This group is collection of notify objects used to send traps on various session restriction crossed. |