CISCO-XGCP-EXT-MIB
69 objects
This MIB module is an extension to CISCO-XGCP-MIB. It defines the parameters related to the following aspects in xGCP protocols: * Default call control parameters in the local media gateway. * Provisioning specific call control profiles which can be associated with the circuits for the call establishment in the circuits.
Imported Objects
| CISCO-MEDIA-GATEWAY-MIB | CCallControlProfileIndex cmgwIndex |
| CISCO-SMI | ciscoMgmt |
| CISCO-TC | CountryCodeITU |
| CISCO-XGCP-MIB | CXgcpRetryMethod |
| INET-ADDRESS-MIB | InetAddress InetAddressType |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Integer32 MODULE-IDENTITY OBJECT-TYPE |
| SNMPv2-TC | DisplayString RowStatus TEXTUAL-CONVENTION TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.9.325 | IdentityciscoXgcpExtMIB | This MIB module is an extension to CISCO-XGCP-MIB. It defines the parameters related to the following aspects in xGCP protocols: * Default call control paramet… | ||
| 1.3.6.1.4.1.9.9.325.1 | NodecxgcpExtObjects | |||
| 1.3.6.1.4.1.9.9.325.1.1 | NodecxgcpExtConfig | |||
| 1.3.6.1.4.1.9.9.325.1.1.1 | TablecxeCallCtrlConfigTable | not-accessible | current | This table contains objects used for configuring general parameters in call control default to the local media gateway in xGCP protocols. |
| 1.3.6.1.4.1.9.9.325.1.1.1.1 | RowcxeCallCtrlConfigEntry | not-accessible | current | There is one entry for each media gateway. The entry will be automatically generated when a media gateway is detected. |
| 1.3.6.1.4.1.9.9.325.1.1.1.1.1 | ColumncxeCallCtrlControlServiceType | read-write | current | This object identifies Type Of Service (TOS) field of IP header for the control packet in VoIP application. |
| 1.3.6.1.4.1.9.9.325.1.1.1.1.2 | ColumncxeCallCtrlBearerServiceType | read-write | current | This object identifies Type Of Service (TOS) field of IP header for the voice payload packet in VoIP application. |
| 1.3.6.1.4.1.9.9.325.1.1.1.1.3 | ColumncxeCallCtrlVoIpDtmfRelayMode | read-write | current | This object defines whether the DTMF (Dual Tone, Multi-Frequency) digits need to be transported to the other endpoint via NSE packets in Voice Over IP. The val… |
| 1.3.6.1.4.1.9.9.325.1.1.1.1.4 | ColumncxeCallCtrlVoIpDtmfCodec | read-write | current | This object identifies DTMF relay codec for VoIP. This object is not applicable if cxeCallCtrlVoIpDtmfRelay is DtmfRelayDisabled. |
| 1.3.6.1.4.1.9.9.325.1.1.1.1.5 | ColumncxeCallCtrlVoAal2DtmfRelayMode | read-write | current | This object defines whether the DTMF (Dual Tone, Multi-Frequency) digits need to be transported to the other endpoint in Voice over AAL2 packets. The value of … |
| 1.3.6.1.4.1.9.9.325.1.1.1.1.6 | ColumncxeCallCtrlVoAal2DtmfCodec | read-write | current | This object identifies DTMF relay CODEC for Voice over AAL2. This object is not applicable if cxeCallCtrlVoAal2DtmfRelay is DtmfRelayDisabled. |
| 1.3.6.1.4.1.9.9.325.1.1.1.1.7 | ColumncxeCallCtrlTsePayload | read-write | current | This object identifies TSE (Telephony Signaling Events) payload type. |
| 1.3.6.1.4.1.9.9.325.1.1.1.1.8 | ColumncxeCallCtrlNetNseTimer | read-write | current | This object identifies Network Signaling Event (NSE) timeout value. |
| 1.3.6.1.4.1.9.9.325.1.1.1.1.9 | ColumncxeCallCtrlRtcpRcvTimer | read-write | current | This object identifies the number of times of Real Time Control Transport (RTCP) report interval if the media gateway has not recieved any RTCP packets from an… |
| 1.3.6.1.4.1.9.9.325.1.1.1.1.10 | ColumncxeCallCtrlIgnoreAal2LcoCodec | read-write | current | This object defines whether to ignore the AAL2 Local Connection Option (LCO) message from the call agent or not. |
| 1.3.6.1.4.1.9.9.325.1.1.1.1.11 | ColumncxeCallCtrlDigitMapOrder | read-write | current | This object defines the type of digit map order. The MGC can advise and load the gateway with a digit map that correspond to the dial plan to collect the acces… |
| 1.3.6.1.4.1.9.9.325.1.1.1.1.12 | ColumncxeCallCtrlT38Inhibited | read-write | current | This object defines whether T.38 is inhibited in the media gateway or not. T.38 is a Fax Relay Protocol defined by ITU for real-time protocol for Fax over IP n… |
| 1.3.6.1.4.1.9.9.325.1.1.1.1.13 | ColumncxeCallCtrlT38NseRspTimer | read-write | current | This object defines a timeout value for a timer. This timer is started after sending a NSE 200 while waiting for the NSE 201 acknowledgement or NSE 202 negativ… |
| 1.3.6.1.4.1.9.9.325.1.1.1.1.14 | ColumncxeCallCtrlT38FecEnabled | read-write | current | This object is used to enable the Forward Error Correction (FEC) for UDP-based fax transport. This object is not applicable if cxeCallCtrlT38Inhibited is set t… |
| 1.3.6.1.4.1.9.9.325.1.1.1.1.15 | ColumncxeCallCtrlT38LsRedundancy | read-write | current | This object determines the extent of the Internet Fax Protocol (IFP) packet transmission redundancy for the low-speed control information exchanged during the … |
| 1.3.6.1.4.1.9.9.325.1.1.1.1.16 | ColumncxeCallCtrlT38HsRedundancy | read-write | current | This object determines the extent of the Internet Fax Protocol (IFP) packet transmission redundancy for the high-speed control and image information exchanged … |
| 1.3.6.1.4.1.9.9.325.1.1.1.1.17 | ColumncxeCallCtrlT38NsfCountryCode | read-write | current | This object specifies the country code for identifying the country where the media gateway with non-standard capabilities was manufactured. This object is not … |
| 1.3.6.1.4.1.9.9.325.1.1.1.1.18 | ColumncxeCallCtrlT38NsfVendorCode | read-write | current | Per its definition (ITU T.35), the Vendor Code (also called the Terminal Provider Code) in the Non-Standard Facilities (NSF) code is a two-byte field identifyi… |
| 1.3.6.1.4.1.9.9.325.1.1.1.1.19 | ColumncxeCallCtrlVselDselFselSupport | read-write | current | This object is used to enable or disable VSEL, DSEL and FSEL support. VSEL: Voice codec, packet length and packet times Selection DSEL: Data codec, packet leng… |
| 1.3.6.1.4.1.9.9.325.1.1.1.1.20 | ColumncxeCallCtrlDefaultBearTraffic | read-write | current | This object specifies the combination of the network type (IP/ATM), virtual circuit type (PVC/SVC) and ATM adaptation layer type (AAL1/AAL2/AAL5) for the conne… |
| 1.3.6.1.4.1.9.9.325.1.1.1.1.21 | ColumncxeCallCtrlLastFailedMgcAddrType | read-only | current | This object indicates the address type, either IPv4 or IPv6, of cxeCallCtrlLastFailedMgcAddress. |
| 1.3.6.1.4.1.9.9.325.1.1.1.1.22 | ColumncxeCallCtrlLastFailedMgcAddress | read-only | current | This object indicates the address of MGC (Media Gateway Controller) with which the media gateway had tried to communicate lastly but failed. |
| 1.3.6.1.4.1.9.9.325.1.1.2 | TablecxeCallCtrlProfileTable | not-accessible | current | This table defines the call control profiles. A call control profile contains the call control information that a call agent uses to establish a call. In the c… |
| 1.3.6.1.4.1.9.9.325.1.1.2.1 | RowcxeCallCtrlProfileEntry | not-accessible | current | Each entry describes an instance of a call control profile in the media gateway. When an entry of call control profile is added to the table, the following obj… |
| 1.3.6.1.4.1.9.9.325.1.1.2.1.1 | ColumncxeCcProfileIndex | not-accessible | current | This object uniquely identifies the call control profile. |
| 1.3.6.1.4.1.9.9.325.1.1.2.1.2 | ColumncxeCcProfileName | read-create | current | A unique name for the profile. The name of the profile has to be unique among all entries of the table. This object is mandatory during the creation of the ent… |
| 1.3.6.1.4.1.9.9.325.1.1.2.1.3 | ColumncxeCcProfileNumVifs | read-only | current | This object reprsents the total number of voice interface (DS0 group) associated with this call control profile. The value of '0' means there is no voice inter… |
| 1.3.6.1.4.1.9.9.325.1.1.2.1.4 | ColumncxeCcProfileMgcGrpNum | read-create | current | This object indicates which MGC Redundant group number that the call control profile will be used. The value is the index to MGC Redundant Group Table (cMgcGrp… |
| 1.3.6.1.4.1.9.9.325.1.1.2.1.5 | ColumncxeCcProfileMgcAddrType | read-create | current | This object identifies the address type applicable to cxeCcProfileMgcAddress. |
| 1.3.6.1.4.1.9.9.325.1.1.2.1.6 | ColumncxeCcProfileMgcAddress | read-create | current | This object specifies the address of Media Gateway Controller (MGC) configured in the profile. When cxeCcProfileMgcGrpNum is non-zero (which menas using MGC gr… |
| 1.3.6.1.4.1.9.9.325.1.1.2.1.7 | ColumncxeCcProfileProtocolIdx | read-create | current | This object specifies the protocol that the media gateway should communicate with MGC during call setup. It is the index of the protocol table(cMediaGwProtocol… |
| 1.3.6.1.4.1.9.9.325.1.1.2.1.8 | ColumncxeCcProfileXgcpRetryMethod | read-create | current | This object specifies the command/response retry method when the media gateway communicates with the MGC in xGCP protocols. |
| 1.3.6.1.4.1.9.9.325.1.1.2.1.9 | ColumncxeCcProfileRetryMax1 | read-create | current | This object contains the suspicious error threshold for signaling messages. |
| 1.3.6.1.4.1.9.9.325.1.1.2.1.10 | ColumncxeCcProfileDnsLookupMax1 | read-create | current | This object enables/disables the Max1 Domain Name Server (DNS) query operation when Max1 expires. This object is used when a gateway-initiated message is not a… |
| 1.3.6.1.4.1.9.9.325.1.1.2.1.11 | ColumncxeCcProfileRetryMax2 | read-create | current | This object contains the disconnect error threshold for signaling messages. |
| 1.3.6.1.4.1.9.9.325.1.1.2.1.12 | ColumncxeCcProfileDnsLookupMax2 | read-create | current | This object enables/disables the Max2 Domain Name Server (DNS) query operation when Max2 expires. This object is used when a gateway-initiated message is not a… |
| 1.3.6.1.4.1.9.9.325.1.1.2.1.13 | ColumncxeCcProfileMwiTimeout | read-create | current | The timeout value for the message waiting indicator tone. Message Waiting Indicator (MWI) tone is used with message waiting services, it indicates that the med… |
| 1.3.6.1.4.1.9.9.325.1.1.2.1.14 | ColumncxeCcProfileTsmaxTimeout | read-create | current | The timeout value for retransmission removal. The gateway uses the value of this object to determine how long for the MGCP messages stored in the retransmissio… |
| 1.3.6.1.4.1.9.9.325.1.1.2.1.15 | ColumncxeCcProfileTdinitTimeout | read-create | current | The voice interface (DS0 group) becomes disconnected when the media gateway tries to communicate with the call agent and the retransmission procedure times out… |
| 1.3.6.1.4.1.9.9.325.1.1.2.1.17 | ColumncxeCcProfileTdminTimeout | read-create | current | The DS0 group (voice interface) becomes disconnected when it tries to communicate with the call agent and the retransmission procedure times out after retrying… |
| 1.3.6.1.4.1.9.9.325.1.1.2.1.18 | ColumncxeCcProfileTdmaxTimeout | read-create | current | The maximum waiting delay (Tdmax) timeout value used by the media gateway to send the Restart In Progress with the restart method as RM:disconnected to the cal… |
| 1.3.6.1.4.1.9.9.325.1.1.2.1.19 | ColumncxeCcProfileTcritTimeout | read-create | current | This object represents the timeout value for the critical timer. If used along with a digit map, the timer is started when the last digit is received. i.e and … |
| 1.3.6.1.4.1.9.9.325.1.1.2.1.20 | ColumncxeCcProfileTparTimeout | read-create | current | This object represents the partial dial timeout and is used along with a digit map as the inter-digit timer. This object is used by call processing when it pro… |
| 1.3.6.1.4.1.9.9.325.1.1.2.1.21 | ColumncxeCcProfileThistTimeout | read-create | current | The MGCP protocol is organized as set of transactions, each of which is composed of a command and a resonse. The MGCP messages, being carried over UDP, may be … |
| 1.3.6.1.4.1.9.9.325.1.1.2.1.22 | ColumncxeCcProfileRtTimeout | read-create | current | This object specifies time for which the local ring back tone (towards the TDM) will be generated unless interrupted (e.g., by the answer from the called party… |
| 1.3.6.1.4.1.9.9.325.1.1.2.1.23 | ColumncxeCcProfileRbkTimeout | read-create | current | This object specifies time for which the remote ring back tone (towards the packet network) will be generated unless interrupted (e.g., by the answer from the … |
| 1.3.6.1.4.1.9.9.325.1.1.2.1.24 | ColumncxeCcProfileCgTimeout | read-create | current | This object specifies time for network congestion tone will be generated. The network congestion tone will be generated when the network resources or bandwidth… |
| 1.3.6.1.4.1.9.9.325.1.1.2.1.25 | ColumncxeCcProfileBzTimeout | read-create | current | This object specifies time for which the busy tone will be generated unless interrupted (e.g., by the hangup from the calling party). The value of '0' indicate… |
| 1.3.6.1.4.1.9.9.325.1.1.2.1.26 | ColumncxeCcProfileDlTimeout | read-create | current | This object specifies time for which the dial tone will be generated unless interrupted (e.g., by the first DTMF digit from the calling party). The value of '0… |
| 1.3.6.1.4.1.9.9.325.1.1.2.1.27 | ColumncxeCcProfileSlTimeout | read-create | current | This object specifies time for which the stutter dial tone or confirmation dial tone will be generated unless interrupted (e.g., by the first DTMF digit from t… |
| 1.3.6.1.4.1.9.9.325.1.1.2.1.28 | ColumncxeCcProfileRgTimeout | read-create | current | This object specifies time for which the ringing cadence will be generated towards the basic PBX unless interrupted (e.g., by the answer from the called party … |
| 1.3.6.1.4.1.9.9.325.1.1.2.1.29 | ColumncxeCcProfileRoTimeout | read-create | current | This object specifies time for which the reorder tone or fast busy tone will be generated unless interrupted (e.g., by the hangup from the called party). The v… |
| 1.3.6.1.4.1.9.9.325.1.1.2.1.30 | ColumncxeCcProfileCot1Timeout | read-create | current | This object specifies time for which the continuity test tone 1 will be generated unless interrupted. The value of '0' indicates that the cadence will be gener… |
| 1.3.6.1.4.1.9.9.325.1.1.2.1.31 | ColumncxeCcProfileCot2Timeout | read-create | current | This object specifies time for which the continuity test tone 2 will be generated unless interrupted. The value of '0' indicates that the cadence will be gener… |
| 1.3.6.1.4.1.9.9.325.1.1.2.1.32 | ColumncxeCcProfileRowStatus | read-create | current | This object is used by users for adding/deleting an entry from the table. The entry can't be deleted if the value of cxeCcProfileNumVifs is greater than zero o… |
| 1.3.6.1.4.1.9.9.325.2 | NodecxeCallCtrlMIBConformance | |||
| 1.3.6.1.4.1.9.9.325.2.1 | NodecxeCallCtrlMIBCompliances | |||
| 1.3.6.1.4.1.9.9.325.2.1.1 | CompliancecxeCallCtrlMIBCompliance | current | The compliance statement for the SNMP entities which implement ciscoXgcpExtMIB. | |
| 1.3.6.1.4.1.9.9.325.2.2 | NodecxeCallCtrlMIBGroups | |||
| 1.3.6.1.4.1.9.9.325.2.2.1 | GroupcxeCallCtrlGroup | current | This group contains objects that apply to the call control general configuration in a media gateway. | |
| 1.3.6.1.4.1.9.9.325.2.2.2 | GroupcxeCcProfileGroup | current | This group contains objects that apply to the call control profile configuration in a media gateway. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| CxeTerminalProviderCode | OCTET STRING (SIZE (0 | 2)) | current | This textual convention represents a Terminal Provider Code for non-standard facilities in telematic services. Unrecognized terminal providers are represented as empty string. |
| DtmfCodecType | INTEGER { dtmfCodecAll (1), dtmfCodecLowRate (2) } | current | DTMF (Dual Tone Multi-Frequency) will be specially handled under the specified codec rates. dtmfCodecAll - DTMF will be specially handled according to the type indicated in DtmfRelayMode under all codec rates. dtmfCodec… |
| DtmfRelayMode | INTEGER { dtmfRelayDisabled (1), dtmfRelayCisco (2), dtmfRelayNse (3), dtmfRelayOutOfBand (4), dtmfRelayNteGw (5), dtmfRelayNteCa (6), dtmfRelayInband (7), dtmfRelayType3 (8) } | current | This textual convention defines DTMF (Dual Tone Multi- Frequency) relay mode. There are a number of possible ways to relay DTMF digits over a VoIP/VoATM network: dtmfRelayDisabled - DTMF won't be detected and won't be s… |