DGS3627G-SWL3MGMT-MIB
303 objects
The Structure of Layer 3 Network Management Information for the proprietary enterprise.
Imported Objects
| IF-MIB | InterfaceIndex |
| OSPF-MIB | AreaID DesignatedRouterPriority HelloRange Metric PositiveInteger RouterID Status TOSType UpToMaxAge |
| SNMPv2-SMI | Counter32 Integer32 IpAddress MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DisplayString MacAddress PhysAddress RowStatus TimeStamp TruthValue |
| SW36XXPRIMGMT-MIB | dgs3627g |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.171.11.70.8.3 | IdentityswL3MgmtMIB | The Structure of Layer 3 Network Management Information for the proprietary enterprise. | ||
| 1.3.6.1.4.1.171.11.70.8.3.1 | NodeswL3DevMgmt | |||
| 1.3.6.1.4.1.171.11.70.8.3.1.1 | NodeswL3DevCtrl | |||
| 1.3.6.1.4.1.171.11.70.8.3.1.1.1 | ScalarswL3DevCtrlRIPState | read-write | current | This object indicates Routing Information Protocol (RIP) version 2 function is enabled or disabled. |
| 1.3.6.1.4.1.171.11.70.8.3.1.1.2 | ScalarswL3DevCtrlOSPFState | read-write | current | This object indicates OSPF protocol is enabled or disabled. |
| 1.3.6.1.4.1.171.11.70.8.3.1.1.3 | ScalarswL3DevCtrlDVMRPState | read-write | current | This object indicates DVMRP protocol is enabled or disabled. |
| 1.3.6.1.4.1.171.11.70.8.3.1.1.4 | ScalarswL3DevCtrlPIMState | read-write | current | This object indicates PIM protocol is enabled or disabled. |
| 1.3.6.1.4.1.171.11.70.8.3.1.1.5 | ScalarswL3DevCtrlVRRPState | read-write | current | This object indicates VRRP protocol is enabled or disabled. |
| 1.3.6.1.4.1.171.11.70.8.3.1.1.6 | ScalarswL3DevCtrlVrrpPingState | read-write | current | This object indicates VRRP protocol Ping is enabled or disabled. |
| 1.3.6.1.4.1.171.11.70.8.3.1.1.7 | ScalarswL3DevCtrlDHCPAutoConfigState | read-write | current | This object indicates auto config is enabled or disabled. |
| 1.3.6.1.4.1.171.11.70.8.3.2 | NodeswL3IpMgmt | |||
| 1.3.6.1.4.1.171.11.70.8.3.2.1 | NodeswL3IpCtrlMgmt | |||
| 1.3.6.1.4.1.171.11.70.8.3.2.1.3 | TableswL3IpCtrlTable | not-accessible | current | This table contains IP interface information. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.3.1 | RowswL3IpCtrlEntry | not-accessible | current | A list of information about a specific IP interface. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.3.1.1 | ColumnswL3IpCtrlInterfaceName | read-only | current | This object indicates the name of the IP interface. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.3.1.2 | ColumnswL3IpCtrlIfIndex | read-only | current | This object uniquely identifies the IP interface number in the swL3IpCtrlTable. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.3.1.3 | ColumnswL3IpCtrlIpAddr | read-write | current | The IP address of the interface. This object only can take the value of the unicast IP address. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.3.1.4 | ColumnswL3IpCtrlIpSubnetMask | read-write | current | The IP net mask for this interface. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.3.1.5 | ColumnswL3IpCtrlVlanName | read-write | current | This object indicates the IP control entry's VLAN name. The VLAN name in each entry must be unique in the IP Control Table. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.3.1.6 | ColumnswL3IpCtrlProxyArp | read-write | current | This object indicates enable/disable of the proxy ARP function for IPv4. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.3.1.7 | ColumnswL3IpCtrlSecondary | read-create | current | When this is true(1), the IP address is the secondary IP. When false(2), the IP address is the primary IP. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.3.1.8 | ColumnswL3IpCtrlMode | read-write | current | This object indicates the IP operation mode. other(1) - This entry is currently in use but the conditions under which it will remain are determined by each of … |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.3.1.9 | ColumnswL3IpCtrlAdminState | read-write | current | The state of the IP interface. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.3.1.14 | ColumnswL3IpCtrlIpv6LinkLocalAddress | read-only | current | The IPv6 link local address for this interface. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.3.1.15 | ColumnswL3IpCtrlIpv6LinkLocalPrefixLen | read-only | current | The IPv6 prefix length for this IPv6 link local address. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.3.1.16 | ColumnswL3IpCtrlState | read-create | current | This variable displays the status of the entry. The status is used for creating, modifying, and deleting instances of the objects in this table. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.3.1.17 | ColumnswL3IpCtrlIpv6LinkLocalAutoState | read-write | current | The state of the IPv6 link local auto. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.3.1.18 | ColumnswL3IpCtrlLocalProxyArp | read-create | current | If the state is enabled, the switch will be allowed to respond to the proxy ARP proxy ARP when the source IP and destination IP are on the same interface. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.3.1.19 | ColumnswL3IpCtrlIpMtu | read-create | current | The MTU is the largest size of the IP datagram which may be transferred using a specific data link connection. The MTU value is a design parameter of a LAN and… |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.3.1.20 | ColumnswL3IpCtrlDhcpv6ClientState | read-write | current | The state of the Dhcpv6 Client. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.3.1.21 | ColumnswL3IpCtrlIpDirectedBroadcastState | read-write | current | The state of the IP Directed Broadcast. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.3.1.22 | ColumnswL3IpCtrlIpDhcpOption12State | read-write | current | Enable or disable insertion of option 12 in the DHCPDISCOVER and DHCPREQUEST message. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.3.1.23 | ColumnswL3IpCtrlIpDhcpOption12HostName | read-write | current | Specify the host name to be inserted in the DHCPDISCOVER and DHCPREQUEST message. The specified host name must start with a letter, end with a letter or digit,… |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.3.1.24 | ColumnswL3IpCtrlDhcpv6ClientPDState | read-write | current | The state of the Dhcpv6 Client PD. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.3.1.25 | ColumnswL3IpCtrlDhcpv6ClientPDPrefixName | read-write | current | This object indicates the name for the DHCPv6 Client PD. If the swL3IpCtrlDhcpv6ClientPDState is disabled, this object will be clear and can't write. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.3.1.26 | ColumnswL3IpCtrlDhcpv6ClientPDPrefix | read-only | current | The IPv6 prefix obtained form delegation router. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.3.1.27 | ColumnswL3IpCtrlDhcpv6ClientPDPrefixLen | read-only | current | The IPv6 prefix length for the prefix obtained from delegation router. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.4 | TableswL3Ipv6CtrlTable | not-accessible | current | This table contains IPv6 information of an IP interface. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.4.1 | RowswL3Ipv6CtrlEntry | not-accessible | current | A list of IPv6 information about a specific IP interface. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.4.1.1 | ColumnswL3Ipv6CtrlInterfaceName | read-only | current | This object indicates the name of the IP interface. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.4.1.2 | ColumnswL3Ipv6CtrlMaxReassmblySize | read-only | current | Maximum Reassembly Size of the IP interface. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.4.1.3 | ColumnswL3Ipv6CtrlNsRetransTimer | read-write | current | Neighbor solicitation's retransmit timer. The unit is set in milliseconds. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.4.1.5 | ColumnswL3Ipv6CtrlRaState | read-write | current | Neighbor solicited state. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.4.1.6 | ColumnswL3Ipv6CtrlRaMinRtrAdvInterval | read-write | current | The minimum time allowed between sending unsolicited multicast Router Advertisements from the interface. The unit is set in seconds. It must be no less than 3 … |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.4.1.7 | ColumnswL3Ipv6CtrlRaMaxRtrAdvInterval | read-write | current | The maximum time allowed between sending unsolicited multicast Router Advertisements from the interface. The unit is set in seconds. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.4.1.8 | ColumnswL3Ipv6CtrlRaLifeTime | read-write | current | Indicates the lifetime of the router as the default router. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.4.1.9 | ColumnswL3Ipv6CtrlRaReachableTime | read-write | current | Indicates the amount of time that a node can consider a neighboring node reachable after receiving a reachability confirmation. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.4.1.10 | ColumnswL3Ipv6CtrlRaRetransTime | read-write | current | Indicates the amount of time between retransmissions of neighbor solicited messages. The unit is set in millisecond. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.4.1.11 | ColumnswL3Ipv6CtrlRaHopLimit | read-write | current | Indicates the default value of the hop limit field in the IPv6 header for packets sent by hosts that receive this RA message. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.4.1.12 | ColumnswL3Ipv6CtrlRaManagedFlag | read-write | current | When enabled, it indicates that hosts receiving this RA must use a stateful address configuration protocol to obtain an address in the addition to the addresse… |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.4.1.13 | ColumnswL3Ipv6CtrlRaOtherConfigFlag | read-write | current | When enabled, it indicates that hosts receiving this RA must use a stateful address configuration protocol to obtain an on-link address configuration informati… |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.5 | TableswL3Ipv6AddressCtrlTable | not-accessible | current | This table contains IPv6 address information for each IP interface. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.5.1 | RowswL3Ipv6AddressCtrlEntry | not-accessible | current | A list of information about a specific IPv6 address. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.5.1.1 | ColumnswL3Ipv6AddressCtrlInterfaceName | read-only | current | This object indicates the name of the IP interface. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.5.1.2 | ColumnswL3Ipv6Address | read-only | current | Specify the IPv6 address. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.5.1.3 | ColumnswL3Ipv6AddressCtrlPrefixLen | read-only | current | Indicates the prefix length of this IPv6 address. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.5.1.4 | ColumnswL3Ipv6AddressCtrlPreferredLifeTime | read-write | current | Indicates the number of seconds that an address, based on the specified prefix, using the stateless address configuration, remains in preferred state. For an i… |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.5.1.5 | ColumnswL3Ipv6AddressCtrlValidLifeTime | read-write | current | Indicates the number of seconds that an address, based on the specified prefix, using the stateless address configuration, remains valid. For an infinite valid… |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.5.1.6 | ColumnswL3Ipv6AddressCtrlOnLinkFlag | read-write | current | When enabled, the address implied by the specified prefix is available on the link where the RA message is received. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.5.1.7 | ColumnswL3Ipv6AddressCtrlAutonomousFlag | read-write | current | When enabled, the specified prefix will be used to create an autonomous address configuration. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.5.1.8 | ColumnswL3Ipv6AddressCtrlState | read-create | current | This variable displays the status of the entry. The status is used for creating, modifying, and deleting instances of the objects in this table. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.5.1.9 | ColumnswL3Ipv6AddressCtrlAddressType | read-only | current | This object indicates the type of the IPv6 address. manual(1): the IPv6 address is configured by user. dhcpv6(2): the IPv6 address is assigned by DHCPv6 server… |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.6 | TableswL3Ipv6DHCPv6CPDAddrCtrlTable | not-accessible | current | This table contain the information of the IPv6 address which based on DHCPv6 client PD. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.6.1 | RowswL3Ipv6DHCPv6CPDAddrCtrlEntry | not-accessible | current | A list of information about a specific DHCPv6 Client PD IPv6 address. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.6.1.1 | ColumnswL3Ipv6DHCPv6CPDAddrCtrlInterfaceName | read-only | current | This object indicates the name of the IP interface. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.6.1.2 | ColumnswL3Ipv6DHCPv6CPDAddrCtrlPrefixName | read-only | current | This object indicates the name of the prefix based on which the IPv6 address will be generate. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.6.1.3 | ColumnswL3Ipv6DHCPv6CPDAddrCtrlIPv6addr | read-only | current | Specify the suffix of the IPv6 address. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.6.1.4 | ColumnswL3Ipv6DHCPv6CPDAddrCtrlPrefixLen | read-only | current | Indicates the prefix length of this IPv6 address. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.6.1.5 | ColumnswL3Ipv6DHCPv6CPDAddrCtrlState | read-create | current | This variable displays the status of the entry. The status is used for creating and deleting instances of the objects in this table. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.7 | ScalarswL3IpCtrlAllIpIfState | read-write | current | This object indicates all interface function state of the device. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.8 | TableswL3LoopBackIpCtrlTable | not-accessible | current | This table contains loopback IP interface information. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.8.1 | RowswL3LoopBackIpCtrlEntry | not-accessible | current | A list of information about a specific loopback IP interface. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.8.1.1 | ColumnswL3LoopBackIpCtrlInterfaceName | read-only | current | This object indicates the name of the loopback IP interface. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.8.1.2 | ColumnswL3LoopBackIpCtrlIfIndex | read-only | current | This object uniquely identifies the loopback IP interface number in the swL3LoopBackIpCtrlTable. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.8.1.3 | ColumnswL3LoopBackIpCtrlIpAddr | read-create | current | The IP address of the loopback interface. This object only can take the value of the unicast IP address. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.8.1.4 | ColumnswL3LoopBackIpCtrlIpSubnetMask | read-create | current | The IP net mask for this loopback interface. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.8.1.5 | ColumnswL3LoopBackIpCtrlAdminState | read-create | current | The state of the loopback IP interface. |
| 1.3.6.1.4.1.171.11.70.8.3.2.1.8.1.6 | ColumnswL3LoopBackIpCtrlRowStatus | read-create | current | This variable displays the status of the entry. The status is used for creating, modifying, and deleting instances of the objects in this table. |
| 1.3.6.1.4.1.171.11.70.8.3.2.2 | NodeswL3IpFdbMgmt | |||
| 1.3.6.1.4.1.171.11.70.8.3.2.2.1 | TableswL3IpFdbInfoTable | not-accessible | current | A table that contains forwarding and/or filtering information. This information is used by the switch in determining how to propagate the received IP packets. |
| 1.3.6.1.4.1.171.11.70.8.3.2.2.1.1 | RowswL3IpFdbInfoEntry | not-accessible | current | Information about a specific IP address for which the bridge has some forwarding and/or filtering information. |
| 1.3.6.1.4.1.171.11.70.8.3.2.2.1.1.1 | ColumnswL3IpFdbInfoIpAddr | read-only | current | A IP address for which switch has forwarding and/or filtering information. |
| 1.3.6.1.4.1.171.11.70.8.3.2.2.1.1.2 | ColumnswL3IpFdbInfoIpSubnetMask | read-only | current | A IP net mask for this interface for which the switch has forwarding and/or filtering information. |
| 1.3.6.1.4.1.171.11.70.8.3.2.2.1.1.3 | ColumnswL3IpFdbInfoPort | read-only | current | Either the value '0', or the port number of the port on which packet having a IP address equal to the value of the corresponding instance of swL3IpFdbInfoIpAdd… |
| 1.3.6.1.4.1.171.11.70.8.3.2.2.1.1.4 | ColumnswL3IpFdbInfoType | read-only | current | The status of this entry. |
| 1.3.6.1.4.1.171.11.70.8.3.2.4 | ScalarswL3IpArpAgingTime | read-write | current | The timeout period in minutes for aging out dynamically learned ARP information. |
| 1.3.6.1.4.1.171.11.70.8.3.2.5 | TableswL3IpStaticRouteTable | not-accessible | current | This entity's IP static Routing table. |
| 1.3.6.1.4.1.171.11.70.8.3.2.5.1 | RowswL3IpStaticRouteEntry | not-accessible | current | A particular route to a particular destination, under a particular policy. Once an entry is built,it shouldn't be modified.That is,it just supports create and … |
| 1.3.6.1.4.1.171.11.70.8.3.2.5.1.1 | ColumnswL3IpStaticRouteDest | read-only | current | The destination IP address of this route. This object may not take a Multicast (Class D) address value. Any assignment (implicit or otherwise) of an instance o… |
| 1.3.6.1.4.1.171.11.70.8.3.2.5.1.2 | ColumnswL3IpStaticRouteMask | read-only | current | Indicate the mask to be logical-AND with the destination address before being compared to the value in the swL3IpStaticRouteDest field. For those systems that … |
| 1.3.6.1.4.1.171.11.70.8.3.2.5.1.3 | ColumnswL3IpStaticRouteBkupState | read-create | current | The routing state for this route.The value SHOULD be primary(1), backup(2) or none(3). |
| 1.3.6.1.4.1.171.11.70.8.3.2.5.1.4 | ColumnswL3IpStaticRouteNextHop | read-create | current | Specifies the IP address for the next hop router. An IP address of 255.255.255.255 denotes a Null interface as the next hop. |
| 1.3.6.1.4.1.171.11.70.8.3.2.5.1.5 | ColumnswL3IpStaticRouteMetric | read-create | current | Specifies the routing metric for this route. |
| 1.3.6.1.4.1.171.11.70.8.3.2.5.1.6 | ColumnswL3IpStaticRouteStatus | read-create | current | This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from e… |
| 1.3.6.1.4.1.171.11.70.8.3.2.5.1.7 | ColumnswL3IpStaticRouteWeight | read-create | current | Specifies the weight value. Used for the weighted multipath. |
| 1.3.6.1.4.1.171.11.70.8.3.2.5.1.8 | ColumnswL3IpStaticRouteInterfaceName | read-only | current | Specifies the name of the IP interface. |
| 1.3.6.1.4.1.171.11.70.8.3.2.6 | NodeswL3IpMcastMgmt | |||
| 1.3.6.1.4.1.171.11.70.8.3.2.6.1 | TableswL3IpMcastStaticRouteTable | not-accessible | current | IP multicast static routing allows you to have multicast paths diverge from the unicast paths. |
| 1.3.6.1.4.1.171.11.70.8.3.2.6.1.1 | RowswL3IpMcastStaticRouteEntry | not-accessible | current | A list of information about IP multicast static routes. |
| 1.3.6.1.4.1.171.11.70.8.3.2.6.1.1.1 | ColumnswL3IpMcastStaticRouteIpmrouteAddr | read-only | current | If the source IP address of the received IP multicast packet matches this Ipmrouteaddress, the RPF network is used to do an RPF check. |
| 1.3.6.1.4.1.171.11.70.8.3.2.6.1.1.2 | ColumnswL3IpMcastStaticRouteIpmrouteMask | read-only | current | This specifies an IP net Mask for this interface. |
| 1.3.6.1.4.1.171.11.70.8.3.2.6.1.1.3 | ColumnswL3IpMcastStaticRouteRpfAddr | read-create | current | If the source IP address of the received IP multicast packet matches the Ipmrouteaddress, the Rpfaddress will be used to check whether the packet received is f… |
| 1.3.6.1.4.1.171.11.70.8.3.2.6.1.1.4 | ColumnswL3IpMcastStaticRouteRowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.11.70.8.3.3 | NodeswL3RelayMgmt | |||
| 1.3.6.1.4.1.171.11.70.8.3.3.1 | NodeswL3RelayDhcpMgmt | |||
| 1.3.6.1.4.1.171.11.70.8.3.3.1.1 | ScalarswL3RelayDhcpState | read-write | current | This object indicates if the DHCP Relay function is enabled or disabled. |
| 1.3.6.1.4.1.171.11.70.8.3.3.1.2 | ScalarswL3RelayDhcpHopCount | read-write | current | This object indicates the maximum number of router hops that the BOOTP packets can cross. |
| 1.3.6.1.4.1.171.11.70.8.3.3.1.3 | ScalarswL3RelayDhcpTimeThreshold | read-write | current | This object indicates the minimum time in seconds within which the switch must relay the DHCP request. If this time is exceeded, the switch will drop the DHCP … |
| 1.3.6.1.4.1.171.11.70.8.3.3.1.4 | TableswL3RelayDhcpCtrlTable | not-accessible | current | This table specifies the IP address as a destination to forward (relay) DHCP packets to. |
| 1.3.6.1.4.1.171.11.70.8.3.3.1.4.1 | RowswL3RelayDhcpCtrlEntry | not-accessible | current | A list of information specifying the IP address as a destination to forward (relay) DHCP packets to. |
| 1.3.6.1.4.1.171.11.70.8.3.3.1.4.1.1 | ColumnswL3RelayDhcpCtrlInterfaceName | read-only | current | The name of the IP interface. |
| 1.3.6.1.4.1.171.11.70.8.3.3.1.4.1.2 | ColumnswL3RelayDhcpCtrlServer | read-only | current | The DHCP server IP address. |
| 1.3.6.1.4.1.171.11.70.8.3.3.1.4.1.3 | ColumnswL3RelayDhcpCtrlState | read-write | current | This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from e… |
| 1.3.6.1.4.1.171.11.70.8.3.3.1.5 | ScalarswL3RelayDhcpOption82State | read-write | current | This object indicates DHCP Relay Option 82 function is enabled or disabled. |
| 1.3.6.1.4.1.171.11.70.8.3.3.1.6 | ScalarswL3RelayDhcpOption82CheckState | read-write | current | This object indicates DHCP Relay Option 82 Check function is enabled or disabled. |
| 1.3.6.1.4.1.171.11.70.8.3.3.1.7 | ScalarswL3RelayDhcpOption82Policy | read-write | current | This object indicates DHCP Relay Option 82 Policy. |
| 1.3.6.1.4.1.171.11.70.8.3.3.1.8 | NodeswL3DHCPRelayOption60 | |||
| 1.3.6.1.4.1.171.11.70.8.3.3.1.8.1 | ScalarswL3DHCPRelayOption60State | read-write | current | This object indicates DHCP relay option 60 function is enabled or disabled. |
| 1.3.6.1.4.1.171.11.70.8.3.3.1.8.2 | ScalarswL3DHCPRelayOption60DefMode | read-write | current | This object indicates default mode that has no option 60 mathcing rules. relay(1): means to relay the packet to the IP address which is specified by swL3DHCPRe… |
| 1.3.6.1.4.1.171.11.70.8.3.3.1.8.3 | TableswL3DHCPRelayOption60DefTable | not-accessible | current | This table indicates the default relay servers for the packet that has no option 60 mathcing rules. |
| 1.3.6.1.4.1.171.11.70.8.3.3.1.8.3.1 | RowswL3DHCPRelayOption60DefEntry | not-accessible | current | A list of information indicates the default relay servers for the packet that has no option 60 mathcing rules. |
| 1.3.6.1.4.1.171.11.70.8.3.3.1.8.3.1.1 | ColumnswL3DHCPRelayOption60DefRelayIp | read-only | current | This object indicates the IP address of default relay server. |
| 1.3.6.1.4.1.171.11.70.8.3.3.1.8.3.1.2 | ColumnswL3DHCPRelayOption60DefRowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.11.70.8.3.3.1.8.4 | TableswL3DHCPRelayOption60Table | not-accessible | current | This table indicates the relay servers for the packet at option 60 rules. |
| 1.3.6.1.4.1.171.11.70.8.3.3.1.8.4.1 | RowswL3DHCPRelayOption60Entry | not-accessible | current | A list of information indicates the relay servers for the packet at option 60 rules. |
| 1.3.6.1.4.1.171.11.70.8.3.3.1.8.4.1.1 | ColumnswL3DHCPRelayOption60String | read-only | current | This object indicates string of this entry. Note that it is theoretically possible for a valid string to exceed the allowed length of an SNMP object identifier… |
| 1.3.6.1.4.1.171.11.70.8.3.3.1.8.4.1.2 | ColumnswL3DHCPRelayOption60RelayIp | read-only | current | This object indicates the IP address of relay server. |
| 1.3.6.1.4.1.171.11.70.8.3.3.1.8.4.1.3 | ColumnswL3DHCPRelayOption60MatchType | read-create | current | This object indicates match state of this entry. exact(1): means the option 60 string in the packet must full match with the specified string. partial(2): mean… |
| 1.3.6.1.4.1.171.11.70.8.3.3.1.8.4.1.4 | ColumnswL3DHCPRelayOption60RowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.11.70.8.3.3.1.9 | NodeswL3DHCPRelayOption61 | |||
| 1.3.6.1.4.1.171.11.70.8.3.3.1.9.1 | ScalarswL3DHCPRelayOption61State | read-write | current | This object indicates DHCP relay option 61 function is enabled or disabled. |
| 1.3.6.1.4.1.171.11.70.8.3.3.1.9.2 | ScalarswL3DHCPRelayOption61DefMode | read-write | current | This object indicates default mode that has no option 61 mathcing rules. relay(1): means to relay the packet to the IP address which is specified by swL3DHCPRe… |
| 1.3.6.1.4.1.171.11.70.8.3.3.1.9.3 | ScalarswL3DHCPRelayOption61DefRelayIp | read-write | current | This object indicates the IP address of default relay server that has no option 61 mathcing rules. Pay attention to when swL3DHCPRelayOption61Mode is: relay(1)… |
| 1.3.6.1.4.1.171.11.70.8.3.3.1.9.4 | TableswL3DHCPRelayOption61Table | not-accessible | current | This table indicates the relay servers for the packet at option 61 rules. |
| 1.3.6.1.4.1.171.11.70.8.3.3.1.9.4.1 | RowswL3DHCPRelayOption61Entry | not-accessible | current | A list of information indicates the relay servers for the packet at option 61 rules. |
| 1.3.6.1.4.1.171.11.70.8.3.3.1.9.4.1.1 | ColumnswL3DHCPRelayOption61ClientType | read-only | current | This object indicates client type of this entry. mac(1): means the client-ID which is the MAC address of client. string(2): means the client-ID which is specif… |
| 1.3.6.1.4.1.171.11.70.8.3.3.1.9.4.1.2 | ColumnswL3DHCPRelayOption61ClientID | read-only | current | This object indicates string of this entry. When swL3DHCPRelayOption61ClientType is mac(1), the format of this object should be XX-XX-XX-XX-XX-XX (MAC address)… |
| 1.3.6.1.4.1.171.11.70.8.3.3.1.9.4.1.3 | ColumnswL3DHCPRelayOption61Mode | read-create | current | This object indicates mode of this entry. relay(1): means to relay the packet to the IP address which is specified by swL3DHCPRelayOption61RelayIp. drop(2): me… |
| 1.3.6.1.4.1.171.11.70.8.3.3.1.9.4.1.4 | ColumnswL3DHCPRelayOption61RelayIp | read-create | current | This object indicates the IP address of relay server. Pay attention to when swL3DHCPRelayOption61Mode is: relay(1): this object must be set together. drop(2): … |
| 1.3.6.1.4.1.171.11.70.8.3.3.1.9.4.1.5 | ColumnswL3DHCPRelayOption61RowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.11.70.8.3.3.2 | NodeswL3RelayDnsMgmt | |||
| 1.3.6.1.4.1.171.11.70.8.3.3.2.1 | ScalarswL3RelayDnsState | read-write | current | This object indicates if the DNS Relay function is enabled or disabled. |
| 1.3.6.1.4.1.171.11.70.8.3.3.2.2 | ScalarswL3RelayDnsPrimaryServer | read-write | current | This object indicates the address of the primary DNS server. |
| 1.3.6.1.4.1.171.11.70.8.3.3.2.3 | ScalarswL3RelayDnsSecondaryServer | read-write | current | This object indicates the address of the secondary DNS server. |
| 1.3.6.1.4.1.171.11.70.8.3.3.2.4 | ScalarswL3RelayDnsCacheState | read-write | current | This object indicates DNS Relay cache is enabled or disabled. |
| 1.3.6.1.4.1.171.11.70.8.3.3.2.5 | ScalarswL3RelayDnsStaticTableState | read-write | current | This object indicates DNS Relay static table is enabled or disabled. |
| 1.3.6.1.4.1.171.11.70.8.3.3.2.6 | TableswL3RelayDnsCtrlTable | not-accessible | current | This table displays the current DNS relay static table. |
| 1.3.6.1.4.1.171.11.70.8.3.3.2.6.1 | RowswL3RelayDnsCtrlEntry | not-accessible | current | A list of information display the current DNS relay static table. |
| 1.3.6.1.4.1.171.11.70.8.3.3.2.6.1.1 | ColumnswL3RelayDnsCtrlDomainName | read-only | current | The domain name of the entry. |
| 1.3.6.1.4.1.171.11.70.8.3.3.2.6.1.2 | ColumnswL3RelayDnsCtrlIpAddr | read-only | current | The IP address of the entry. |
| 1.3.6.1.4.1.171.11.70.8.3.3.2.6.1.3 | ColumnswL3RelayDnsCtrlState | read-write | current | This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from e… |
| 1.3.6.1.4.1.171.11.70.8.3.4 | TableswL3Md5Table | not-accessible | current | This table displays the current MD5 key table. |
| 1.3.6.1.4.1.171.11.70.8.3.4.1 | RowswL3Md5Entry | not-accessible | current | A list of information displays the current MD5 key table. |
| 1.3.6.1.4.1.171.11.70.8.3.4.1.1 | ColumnswL3Md5KeyId | read-only | current | The MD5 key ID. |
| 1.3.6.1.4.1.171.11.70.8.3.4.1.2 | ColumnswL3Md5Key | read-create | current | An MD5 password of up to 16 bytes. |
| 1.3.6.1.4.1.171.11.70.8.3.4.1.3 | ColumnswL3Md5RowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.11.70.8.3.5 | TableswL3RouteRedistriTable | not-accessible | current | Route redistribution allows routers on the network that are running different routing protocols to exchange routing information. This is accomplished by compar… |
| 1.3.6.1.4.1.171.11.70.8.3.5.1 | RowswL3RouteRedistriEntry | not-accessible | current | A list of information displaying the route redistribution table. |
| 1.3.6.1.4.1.171.11.70.8.3.5.1.1 | ColumnswL3RouteRedistriSrcProtocol | read-only | current | Allows the selection of the protocol of the source device. |
| 1.3.6.1.4.1.171.11.70.8.3.5.1.2 | ColumnswL3RouteRedistriDstProtocol | read-only | current | Allows the selection of the protocol of the destination device. |
| 1.3.6.1.4.1.171.11.70.8.3.5.1.3 | ColumnswL3RouteRedistriType | read-create | current | Allows the selection of one of the methods for calculating the metric value. |
| 1.3.6.1.4.1.171.11.70.8.3.5.1.4 | ColumnswL3RouteRedistriMetric | read-create | current | Allows the entry of an OSPF interface cost. This is analogous to a Hop Count in the RIP routing protocol. The value '0' indicates default value. |
| 1.3.6.1.4.1.171.11.70.8.3.5.1.5 | ColumnswL3RouteRedistriRowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.11.70.8.3.5.1.6 | ColumnswL3RouteRedistriRouteMapName | read-create | current | This Object just works when the destination protocol is BGP and indicate the route-map working when redistribute the route to BGP. |
| 1.3.6.1.4.1.171.11.70.8.3.6 | TableswL3OspfHostTable | not-accessible | current | The list of Hosts, and their metrics, that the router will advertise as host routes. |
| 1.3.6.1.4.1.171.11.70.8.3.6.1 | RowswL3OspfHostEntry | not-accessible | current | A metric to be advertised, for a given type of service, when a given host is reachable. |
| 1.3.6.1.4.1.171.11.70.8.3.6.1.1 | ColumnswL3OspfHostIpAddress | read-only | current | The IP Address of the Host. |
| 1.3.6.1.4.1.171.11.70.8.3.6.1.2 | ColumnswL3OspfHostTOS | read-only | current | The Type of Service of the route being configured. |
| 1.3.6.1.4.1.171.11.70.8.3.6.1.3 | ColumnswL3OspfHostMetric | read-create | current | The Metric to be advertised. |
| 1.3.6.1.4.1.171.11.70.8.3.6.1.4 | ColumnswL3OspfHostAreaID | read-create | current | The Area the Host Entry is to be found within. By default, the area that a subsuming OSPF interface is in, or 0.0.0.0 |
| 1.3.6.1.4.1.171.11.70.8.3.6.1.5 | ColumnswL3OspfHostStatus | read-create | current | This variable displays the status of the entry. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implem… |
| 1.3.6.1.4.1.171.11.70.8.3.7 | TableswL3ospfVirtIfTable | not-accessible | current | Information about this router's virtual inter- faces. |
| 1.3.6.1.4.1.171.11.70.8.3.7.1 | RowswL3ospfVirtIfEntry | not-accessible | current | Information about a single Virtual Interface. |
| 1.3.6.1.4.1.171.11.70.8.3.7.1.1 | ColumnswL3ospfVirtIfAreaId | read-only | current | The Transit Area that the Virtual Link traverses. By definition, this is not 0.0.0.0 |
| 1.3.6.1.4.1.171.11.70.8.3.7.1.2 | ColumnswL3ospfVirtIfNeighbor | read-only | current | The Router ID of the Virtual Neighbor. |
| 1.3.6.1.4.1.171.11.70.8.3.7.1.3 | ColumnswL3ospfVirtIfTransitDelay | read-create | current | The estimated number of seconds it takes to transmit a link- state update packet over this interface. |
| 1.3.6.1.4.1.171.11.70.8.3.7.1.4 | ColumnswL3ospfVirtIfRetransInterval | read-create | current | The number of seconds between link-state ad- vertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitt… |
| 1.3.6.1.4.1.171.11.70.8.3.7.1.5 | ColumnswL3ospfVirtIfHelloInterval | read-create | current | The length of time, in seconds, between the Hello packets that the router sends on the in- terface. This value must be the same for the virtual neighbor. |
| 1.3.6.1.4.1.171.11.70.8.3.7.1.6 | ColumnswL3ospfVirtIfRtrDeadInterval | read-create | current | The number of seconds that a router's Hello packets have not been seen before it's neigh- bors declare the router down. This should be some multiple of the Hel… |
| 1.3.6.1.4.1.171.11.70.8.3.7.1.7 | ColumnswL3ospfVirtIfState | read-only | current | OSPF virtual interface states. |
| 1.3.6.1.4.1.171.11.70.8.3.7.1.8 | ColumnswL3ospfVirtIfEvents | read-only | current | The number of state changes or error events on this Virtual Link |
| 1.3.6.1.4.1.171.11.70.8.3.7.1.9 | ColumnswL3ospfVirtIfAuthType | read-create | current | The authentication type specified for a virtu- al interface. Additional authentication types may be assigned locally. |
| 1.3.6.1.4.1.171.11.70.8.3.7.1.10 | ColumnswL3ospfVirtIfAuthKey | read-create | current | If Authentication Type is simplePassword, the device will left adjust and zero fill to 8 oc- tets. Note that unauthenticated interfaces need no authentication … |
| 1.3.6.1.4.1.171.11.70.8.3.7.1.11 | ColumnswL3ospfVirtIfAuthKeyID | read-create | current | The MD5 key ID. |
| 1.3.6.1.4.1.171.11.70.8.3.7.1.12 | ColumnswL3ospfVirtIfStatus | read-create | current | This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is impl… |
| 1.3.6.1.4.1.171.11.70.8.3.8 | TableswL3ospfIfTable | not-accessible | current | The OSPF Interface Table describes the inter- faces from the viewpoint of OSPF. |
| 1.3.6.1.4.1.171.11.70.8.3.8.1 | RowswL3ospfIfEntry | not-accessible | current | The OSPF Interface Entry describes one inter- face from the viewpoint of OSPF. |
| 1.3.6.1.4.1.171.11.70.8.3.8.1.1 | ColumnswL3ospfIfIpAddress | read-only | current | The IP address of this OSPF interface. |
| 1.3.6.1.4.1.171.11.70.8.3.8.1.2 | ColumnswL3ospfAddressLessIf | read-only | current | For the purpose of easing the instancing of addressed and addressless interfaces; This variable takes the value 0 on interfaces with IP Addresses, and the corr… |
| 1.3.6.1.4.1.171.11.70.8.3.8.1.3 | ColumnswL3ospfIfAreaId | read-write | current | A 32-bit integer uniquely identifying the area to which the interface connects. Area ID 0.0.0.0 is used for the OSPF backbone. |
| 1.3.6.1.4.1.171.11.70.8.3.8.1.4 | ColumnswL3ospfIfType | read-write | current | The OSPF interface type. By way of a default, this field may be intuited from the corresponding value of ifType. Broad- cast LANs, such as Ethernet and IEEE 80… |
| 1.3.6.1.4.1.171.11.70.8.3.8.1.5 | ColumnswL3ospfIfAdminStat | read-write | current | The OSPF interface's administrative status. The value formed on the interface, and the in- terface will be advertised as an internal route to some area. The va… |
| 1.3.6.1.4.1.171.11.70.8.3.8.1.6 | ColumnswL3ospfIfRtrPriority | read-write | current | The priority of this interface. Used in multi-access networks, this field is used in the designated router election algorithm. The value 0 signifies that the r… |
| 1.3.6.1.4.1.171.11.70.8.3.8.1.7 | ColumnswL3ospfIfTransitDelay | read-write | current | The estimated number of seconds it takes to transmit a link state update packet over this interface. |
| 1.3.6.1.4.1.171.11.70.8.3.8.1.8 | ColumnswL3ospfIfRetransInterval | read-write | current | The number of seconds between link-state ad- vertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitt… |
| 1.3.6.1.4.1.171.11.70.8.3.8.1.9 | ColumnswL3ospfIfHelloInterval | read-write | current | The length of time, in seconds, between the Hello packets that the router sends on the in- terface. This value must be the same for all routers attached to a c… |
| 1.3.6.1.4.1.171.11.70.8.3.8.1.10 | ColumnswL3ospfIfRtrDeadInterval | read-write | current | The number of seconds that a router's Hello packets have not been seen before it's neigh- bors declare the router down. This should be some multiple of the Hel… |
| 1.3.6.1.4.1.171.11.70.8.3.8.1.11 | ColumnswL3ospfIfPollInterval | read-write | current | The larger time interval, in seconds, between the Hello packets sent to an inactive non- broadcast multi- access neighbor. |
| 1.3.6.1.4.1.171.11.70.8.3.8.1.12 | ColumnswL3ospfIfState | read-only | current | The OSPF Interface State. |
| 1.3.6.1.4.1.171.11.70.8.3.8.1.13 | ColumnswL3ospfIfDesignatedRouter | read-only | current | The IP Address of the Designated Router. |
| 1.3.6.1.4.1.171.11.70.8.3.8.1.14 | ColumnswL3ospfIfBackupDesignatedRouter | read-only | current | The IP Address of the Backup Designated Router. |
| 1.3.6.1.4.1.171.11.70.8.3.8.1.15 | ColumnswL3ospfIfEvents | read-only | current | The number of times this OSPF interface has changed its state, or an error has occurred. |
| 1.3.6.1.4.1.171.11.70.8.3.8.1.16 | ColumnswL3ospfIfMulticastForwarding | read-write | current | The way multicasts should forwarded on this interface; not forwarded, forwarded as data link multicasts, or forwarded as data link uni- casts. Data link multic… |
| 1.3.6.1.4.1.171.11.70.8.3.8.1.17 | ColumnswL3ospfIfDemand | read-write | current | Indicates whether Demand OSPF procedures (hel- lo supression to FULL neighbors and setting the DoNotAge flag on proogated LSAs) should be per- formed on this i… |
| 1.3.6.1.4.1.171.11.70.8.3.8.1.18 | ColumnswL3ospfIfAuthType | read-write | current | The authentication type specified for an in- terface. Additional authentication types may be assigned locally. |
| 1.3.6.1.4.1.171.11.70.8.3.8.1.19 | ColumnswL3ospfIfAuthKey | read-write | current | The Authentication Key. If the Area's Author- ization Type is simplePassword, and the key length is shorter than 8 octets, the agent will left adjust and zero … |
| 1.3.6.1.4.1.171.11.70.8.3.8.1.20 | ColumnswL3ospfIfAuthKeyID | read-write | current | The MD5 key ID. |
| 1.3.6.1.4.1.171.11.70.8.3.8.1.21 | ColumnswL3ospfIfPassiveMode | read-write | current | Assign the designated entry to be a passive interface. |
| 1.3.6.1.4.1.171.11.70.8.3.8.1.23 | ColumnswL3ospfIfMetric | read-write | current | The Metric to be advertised. |
| 1.3.6.1.4.1.171.11.70.8.3.8.1.24 | ColumnswL3ospfIfDistributeListInType | read-write | current | The type of route filter for distribute list in. |
| 1.3.6.1.4.1.171.11.70.8.3.8.1.25 | ColumnswL3ospfIfDistributeListInName | read-write | current | The name of route filter for distribute list in. |
| 1.3.6.1.4.1.171.11.70.8.3.9 | NodeswL3RoutePreference | |||
| 1.3.6.1.4.1.171.11.70.8.3.9.1 | ScalarswL3RoutePreferenceRIP | read-write | current | Used to configure the route preference of RIP. |
| 1.3.6.1.4.1.171.11.70.8.3.9.2 | ScalarswL3RoutePreferenceOSPFIntra | read-write | current | Used to configure the route preference of OSPF Intra. |
| 1.3.6.1.4.1.171.11.70.8.3.9.3 | ScalarswL3RoutePreferenceStatic | read-write | current | Used to configure the route preference of Static. |
| 1.3.6.1.4.1.171.11.70.8.3.9.4 | ScalarswL3RoutePreferenceLocal | read-only | current | Used to read the route preference of Local. |
| 1.3.6.1.4.1.171.11.70.8.3.9.5 | ScalarswL3RoutePreferenceOSPFInter | read-write | current | Used to configure the route preference of OSPF Inter. |
| 1.3.6.1.4.1.171.11.70.8.3.9.6 | ScalarswL3RoutePreferenceOSPFExtT1 | read-write | current | Used to configure the route preference of OSPFExtT1. |
| 1.3.6.1.4.1.171.11.70.8.3.9.7 | ScalarswL3RoutePreferenceOSPFExtT2 | read-write | current | Used to configure the route preference of OSPF ExtT2. |
| 1.3.6.1.4.1.171.11.70.8.3.9.8 | ScalarswL3RoutePreferenceDefault | read-write | current | Used to configure the route preference of Default route. |
| 1.3.6.1.4.1.171.11.70.8.3.9.9 | ScalarswL3RoutePreferenceEBGP | read-write | current | Used to configure the route preference of EBGP. |
| 1.3.6.1.4.1.171.11.70.8.3.9.10 | ScalarswL3RoutePreferenceIBGP | read-write | current | Used to configure the route preference of IBGP. |
| 1.3.6.1.4.1.171.11.70.8.3.10 | TableswL3ospfAreaTable | not-accessible | current | Information describing the configured parame- ters and cumulative statistics of the router's attached areas. |
| 1.3.6.1.4.1.171.11.70.8.3.10.1 | RowswL3ospfAreaEntry | not-accessible | current | Information describing the configured parame- ters and cumulative statistics of one of the router's attached areas. |
| 1.3.6.1.4.1.171.11.70.8.3.10.1.1 | ColumnswL3ospfAreaId | read-only | current | A 32-bit integer uniquely identifying an area. Area ID 0.0.0.0 is used for the OSPF backbone. |
| 1.3.6.1.4.1.171.11.70.8.3.10.1.2 | ColumnswL3ospfAreaType | read-create | obsolete | The type specified for an area. |
| 1.3.6.1.4.1.171.11.70.8.3.10.1.3 | ColumnswL3ospfAreaSummaryState | read-create | current | Whether the summary LSA is effective for this area. |
| 1.3.6.1.4.1.171.11.70.8.3.10.1.4 | ColumnswL3ospfAreaMetric | read-write | current | Enter the metric (1 - 65535; 0 for auto cost) of this area. |
| 1.3.6.1.4.1.171.11.70.8.3.10.1.5 | ColumnswL3ospfAreaTranslateState | read-create | current | . |
| 1.3.6.1.4.1.171.11.70.8.3.10.1.6 | ColumnswL3ospfAreaStatus | read-create | current | This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is impl… |
| 1.3.6.1.4.1.171.11.70.8.3.12 | TableswL3dvmrpInterfaceTable | not-accessible | current | The (conceptual) table listing the router's multicast- capable interfaces. |
| 1.3.6.1.4.1.171.11.70.8.3.12.1 | RowswL3dvmrpInterfaceEntry | not-accessible | current | An entry (conceptual row) in the dvmrpInterfaceTable. This row augments ipMRouteInterfaceEntry in the IP Multicast MIB, where the threshold object resides. |
| 1.3.6.1.4.1.171.11.70.8.3.12.1.1 | ColumnswL3dvmrpInterfaceIfIndex | not-accessible | current | The ifIndex value of the interface for which DVMRP is enabled. |
| 1.3.6.1.4.1.171.11.70.8.3.12.1.2 | ColumnswL3dvmrpInterfaceLocalAddress | read-create | current | The IP address this system will use as a source address on this interface. On unnumbered interfaces, it must be the same value as dvmrpInterfaceLocalAddress fo… |
| 1.3.6.1.4.1.171.11.70.8.3.12.1.3 | ColumnswL3dvmrpInterfaceMetric | read-create | current | The distance metric for this interface which is used to calculate distance vectors. |
| 1.3.6.1.4.1.171.11.70.8.3.12.1.4 | ColumnswL3dvmrpInterfaceProbe | read-create | current | Probe distribution interval. |
| 1.3.6.1.4.1.171.11.70.8.3.12.1.5 | ColumnswL3dvmrpInterfaceNbrTimeout | read-create | current | Used to set the timer before neighbors are timed out. |
| 1.3.6.1.4.1.171.11.70.8.3.12.1.6 | ColumnswL3dvmrpInterfaceStatus | read-create | current | The status of this entry. Creating the entry enables DVMRP on the virtual interface; destroying the entry or setting it to notInService disables DVMRP on the v… |
| 1.3.6.1.4.1.171.11.70.8.3.12.1.7 | ColumnswL3dvmrpInterfaceRcvBadPkts | read-only | current | The number of DVMRP packets received on the interface by the DVMRP process which were subsequently discarded as invalid (e.g. invalid packet format, or a route… |
| 1.3.6.1.4.1.171.11.70.8.3.12.1.8 | ColumnswL3dvmrpInterfaceRcvBadRoutes | read-only | current | The number of routes, in valid DVMRP packets, which were ignored because the entry was invalid. |
| 1.3.6.1.4.1.171.11.70.8.3.13 | NodeswL3OspfLsdbMgmt | |||
| 1.3.6.1.4.1.171.11.70.8.3.13.1 | TableswL3OspfInternalLsdbTable | not-accessible | current | The OSPF Process's Link State Database. |
| 1.3.6.1.4.1.171.11.70.8.3.13.1.1 | RowswL3OspfInternalLsdbEntry | not-accessible | current | A single Link State Advertisement. |
| 1.3.6.1.4.1.171.11.70.8.3.13.1.1.1 | ColumnswL3OspfInternalLsdbAreaId | read-only | current | The 32 bit identifier of the Area from which the LSA was received. |
| 1.3.6.1.4.1.171.11.70.8.3.13.1.1.2 | ColumnswL3OspfInternalLsdbType | read-only | current | The type of the link state advertisement. Each link state type has a separate advertise- ment format. |
| 1.3.6.1.4.1.171.11.70.8.3.13.1.1.3 | ColumnswL3OspfInternalLsdbLsid | read-only | current | The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being desc… |
| 1.3.6.1.4.1.171.11.70.8.3.13.1.1.4 | ColumnswL3OspfInternalLsdbRouterId | read-only | current | The 32 bit number that uniquely identifies the originating router in the Autonomous System. |
| 1.3.6.1.4.1.171.11.70.8.3.13.1.1.5 | ColumnswL3OspfInternalLsdbMetric | read-only | current | Enter the metric (1 - 65535; 0 for auto cost) of this area. |
| 1.3.6.1.4.1.171.11.70.8.3.13.1.1.6 | ColumnswL3OspfInternalLsdbSequenceNo | read-only | current | The sequence number field is a signed 32-bit integer. It is used to detect old and dupli- cate link state advertisements. The space of sequence numbers is line… |
| 1.3.6.1.4.1.171.11.70.8.3.13.1.1.7 | ColumnswL3OspfInternalLsdbAge | read-only | current | This field is the age of the link state adver- tisement in seconds. |
| 1.3.6.1.4.1.171.11.70.8.3.13.1.1.8 | ColumnswL3OspfInternalLsdbChecksum | read-only | current | This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can… |
| 1.3.6.1.4.1.171.11.70.8.3.13.2 | TableswL3OspfExternalLsdbTable | not-accessible | current | The OSPF Process's Links State Database. |
| 1.3.6.1.4.1.171.11.70.8.3.13.2.1 | RowswL3OspfExternalLsdbEntry | not-accessible | current | A single Link State Advertisement. |
| 1.3.6.1.4.1.171.11.70.8.3.13.2.1.1 | ColumnswL3OspfExternalLsdbType | read-only | current | The type of the link state advertisement. Each link state type has a separate advertise- ment format. |
| 1.3.6.1.4.1.171.11.70.8.3.13.2.1.2 | ColumnswL3OspfExternalLsdbLsid | read-only | current | The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being desc… |
| 1.3.6.1.4.1.171.11.70.8.3.13.2.1.3 | ColumnswL3OspfExternalLsdbRouterId | read-only | current | The 32 bit number that uniquely identifies the originating router in the Autonomous System. |
| 1.3.6.1.4.1.171.11.70.8.3.13.2.1.4 | ColumnswL3OspfExternalLsdbMetric | read-only | current | Enter the metric (1 - 65535; 0 for auto cost) of this area. |
| 1.3.6.1.4.1.171.11.70.8.3.13.2.1.5 | ColumnswL3OspfExternalLsdbMetricType | read-only | current | Enter the metric type of this area. |
| 1.3.6.1.4.1.171.11.70.8.3.13.2.1.6 | ColumnswL3OspfExternalLsdbSequenceNo | read-only | current | The sequence number field is a signed 32-bit integer. It is used to detect old and dupli- cate link state advertisements. The space of sequence numbers is line… |
| 1.3.6.1.4.1.171.11.70.8.3.13.2.1.7 | ColumnswL3OspfExternalLsdbAge | read-only | current | This field is the age of the link state adver- tisement in seconds. |
| 1.3.6.1.4.1.171.11.70.8.3.13.2.1.8 | ColumnswL3OspfExternalLsdbChecksum | read-only | current | This field is the checksum of the complete contents of the advertisement, except the age field. The age field is the exception so that an advertisement's age c… |
| 1.3.6.1.4.1.171.11.70.8.3.13.2.1.9 | ColumnswL3OspfExternalLsdbForwardingAddress | read-only | current | This field is the forwarding address. |
| 1.3.6.1.4.1.171.11.70.8.3.13.2.1.10 | ColumnswL3OspfExternalLsdbRouteTag | read-only | current | This field is the route tag. |
| 1.3.6.1.4.1.171.11.70.8.3.14 | NodeswL3VrrpOperMgmt | |||
| 1.3.6.1.4.1.171.11.70.8.3.14.1 | TableswL3VrrpOperTable | not-accessible | current | Operations table for a VRRP router which consists of a sequence (i.e., one or more conceptual rows) of 'swL3vrrpOperEntry' items. |
| 1.3.6.1.4.1.171.11.70.8.3.14.1.1 | RowswL3VrrpOperEntry | not-accessible | current | An entry in the vrrpOperTable containing the operational characteristics of a virtual router. On a VRRP router, a given virtual router is identified by a combi… |
| 1.3.6.1.4.1.171.11.70.8.3.14.1.1.1 | ColumnswL3VrrpOperIfIndex | read-only | current | The ifIndex value of the interface for which VRRP is enabled. |
| 1.3.6.1.4.1.171.11.70.8.3.14.1.1.2 | ColumnswL3VrrpOperVrId | read-only | current | This object contains the Virtual Router Identifier (VRID). |
| 1.3.6.1.4.1.171.11.70.8.3.14.1.1.3 | ColumnswL3VrrpOperVirtualMacAddr | read-only | current | The virtual MAC address of the virtual router. Although this object can be derived from the 'swL3VrrpOperVrId' object, it is defined so that it is easily obtai… |
| 1.3.6.1.4.1.171.11.70.8.3.14.1.1.4 | ColumnswL3VrrpOperState | read-only | current | The current state of the virtual router. This object has three defined values: - `initialize', which indicates that all the virtual router is waiting for a sta… |
| 1.3.6.1.4.1.171.11.70.8.3.14.1.1.5 | ColumnswL3VrrpOperAdminState | read-create | current | This object will enable/disable the virtual router function. Setting the value to `up', will transition the state of the virtual router from `initialize' to `b… |
| 1.3.6.1.4.1.171.11.70.8.3.14.1.1.6 | ColumnswL3VrrpOperPriority | read-create | current | This object specifies the priority to be used for the virtual router master election process. Higher values imply higher priority. A priority of '0', although … |
| 1.3.6.1.4.1.171.11.70.8.3.14.1.1.7 | ColumnswL3VrrpOperMasterIpAddr | read-only | current | The master router's real (primary) IP address. This is the IP address listed as the source in VRRP advertisement last received by this virtual router. |
| 1.3.6.1.4.1.171.11.70.8.3.14.1.1.8 | ColumnswL3VrrpOperCriticalIpAddr | read-create | current | In the case where there is more than one IP address for a given `ifIndex', this object is used to specify the IP address that will become the `swL3VrrpOperMast… |
| 1.3.6.1.4.1.171.11.70.8.3.14.1.1.9 | ColumnswL3VrrpOperCheckCriticalIpState | read-create | current | Critical IP state. |
| 1.3.6.1.4.1.171.11.70.8.3.14.1.1.10 | ColumnswL3VrrpOperAuthType | read-create | current | Authentication type used for VRRP protocol exchanges between virtual routers. This value of this object is the same for a given ifIndex. New enumerations to th… |
| 1.3.6.1.4.1.171.11.70.8.3.14.1.1.11 | ColumnswL3VrrpOperAuthKey | read-create | current | The Authentication Key. This object is set according to the value of the 'swL3VrrpOperAuthType' object ('simpleTextPassword' or 'ipAuthenticationHeader'). If t… |
| 1.3.6.1.4.1.171.11.70.8.3.14.1.1.12 | ColumnswL3VrrpOperAdvertisementInterval | read-create | current | The time interval, in seconds, between sending advertisement messages. Only the master router sends VRRP advertisements. |
| 1.3.6.1.4.1.171.11.70.8.3.14.1.1.13 | ColumnswL3VrrpOperPreemptMode | read-create | current | Controls whether a higher priority virtual router will preempt a lower priority master. |
| 1.3.6.1.4.1.171.11.70.8.3.14.1.1.14 | ColumnswL3VrrpOperVirtualRouterUpTime | read-only | current | This is the value of the `sysUpTime' object when this virtual router (i.e., the `swL3VrrpOperState') transitioned out of `initialized'. |
| 1.3.6.1.4.1.171.11.70.8.3.14.1.1.15 | ColumnswL3VrrpOperVirtualIpAddr | read-create | current | The assigned IP addresses that a virtual router is responsible for backing up. |
| 1.3.6.1.4.1.171.11.70.8.3.14.1.1.16 | ColumnswL3VrrpOperRowStatus | read-create | current | The row status variable, used in accordance to installation and removal conventions for conceptual rows. The rowstatus of a currently active row in the vrrpOpe… |
| 1.3.6.1.4.1.171.11.70.8.3.15 | NodeswL3OspfECMPMgmt | |||
| 1.3.6.1.4.1.171.11.70.8.3.15.1 | ScalarswL3OspfECMPIpDestination | read-write | current | If set to 'enabled (1)', the ECMP algorithm will include the destination IP. |
| 1.3.6.1.4.1.171.11.70.8.3.15.2 | ScalarswL3OspfECMPIpSource | read-write | current | If set to 'enabled (1)', the ECMP algorithm will include the lower 5 bits of the source IP. This attribution is mutually exclusive with crc_low and crc_high. I… |
| 1.3.6.1.4.1.171.11.70.8.3.15.3 | ScalarswL3OspfECMPCrcLow | read-write | current | If set to 'enabled (1)', the ECMP algorithm will include the lower 5 bits of the CRC. This attribution is mutually exclusive with crc_high and ip_source. If se… |
| 1.3.6.1.4.1.171.11.70.8.3.15.4 | ScalarswL3OspfECMPCrcHigh | read-write | current | If set to 'enabled (1)', the ECMP algorithm will include the upper 5 bits of the CRC. This attribution is mutually exclusive with ip_source and crc_low. If set… |
| 1.3.6.1.4.1.171.11.70.8.3.15.5 | ScalarswL3OspfECMPTCPorUDPport | read-write | current | If set to 'enabled (1)', the ECMP algorithm will include the TCP or UDP port. |
| 1.3.6.1.4.1.171.11.70.8.3.15.6 | ScalarswL3OspfECMPState | read-write | current | This object indicates the state of the OSPF ECMP function. |
| 1.3.6.1.4.1.171.11.70.8.3.19 | TableswL3RIPInboundRouteFilterTable | not-accessible | current | The list of inbound route filter on RIP interfaces. |
| 1.3.6.1.4.1.171.11.70.8.3.19.1 | RowswL3RIPInboundRouteFilterEntry | not-accessible | current | The information of inbound route filter on RIP interfaces. |
| 1.3.6.1.4.1.171.11.70.8.3.19.1.1 | ColumnswL3RIPInboundRouteFilterIfIpAddress | read-only | current | The IP Address of the RIP interface. |
| 1.3.6.1.4.1.171.11.70.8.3.19.1.2 | ColumnswL3RIPInboundRouteFilterType | read-write | current | The type of inbound route filter for the RIP interface. |
| 1.3.6.1.4.1.171.11.70.8.3.19.1.3 | ColumnswL3RIPInboundRouteFilterName | read-write | current | The name of inbound route filter for the RIP interface. |
| 1.3.6.1.4.1.171.11.70.8.3.20 | TableswL3Route6RedistriTable | not-accessible | current | IPv6 Route redistribution allows routers on the network that are running different routing protocols to exchange routing information. This is accomplished by c… |
| 1.3.6.1.4.1.171.11.70.8.3.20.1 | RowswL3Route6RedistriEntry | not-accessible | current | A list of information displaying the IPv6 route redistribution table. |
| 1.3.6.1.4.1.171.11.70.8.3.20.1.1 | ColumnswL3Route6RedistriSrcProtocol | read-only | current | Allows the selection of the protocol of the source device. |
| 1.3.6.1.4.1.171.11.70.8.3.20.1.2 | ColumnswL3Route6RedistriDstProtocol | read-only | current | Allows the selection of the protocol of the destination device. |
| 1.3.6.1.4.1.171.11.70.8.3.20.1.3 | ColumnswL3Route6RedistriType | read-create | current | Allows the selection of one of the methods for calculating the metric value. |
| 1.3.6.1.4.1.171.11.70.8.3.20.1.4 | ColumnswL3Route6RedistriMetric | read-create | current | Allows the entry of an OSPFv3 interface cost. This is analogous to a Hop Count in the RIPng routing protocol. The value '0' indicates default value. |
| 1.3.6.1.4.1.171.11.70.8.3.20.1.5 | ColumnswL3Route6RedistriRowStatus | read-create | current | This object indicates the status of this entry. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| Ipv6Address | OCTET STRING (SIZE (16)) | current | This data type is used to model IPv6 addresses. This is a binary string of 16 octets in network byte-order. |
| VrId | Integer32 (1..255) | current | A number which, along with an interface index (ifIndex), serves to uniquely identify a virtual router on a given VRRP router. A set of one or more associated addresses is assigned to a VRID. |