DLINK-3100-IpRouter
123 objects
The private MIB module definition for RND router MIB.
Imported Objects
| DLINK-3100-IP | ipRedundancy ipRipFilter ipRouteLeaking ipSpec rip2Spec rlIpRoutingProtPreference rlOspf |
| OSPF-MIB | AreaID ospfIfEntry ospfVirtIfEntry RouterID |
| RFC1389-MIB | rip2IfConfEntry |
| SNMPv2-SMI | Counter32 Integer32 IpAddress MODULE-IDENTITY OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DisplayString RowStatus TEXTUAL-CONVENTION TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.171.10.94.89.89.26.3.1 | TablersRip2IfConfTable | not-accessible | current | This table is extension of rip2IfConfTable (RFC 1389 ,RIP 2) |
| 1.3.6.1.4.1.171.10.94.89.89.26.3.1.1 | RowrsRip2IfConfEntry | not-accessible | current | The row definition for this table. |
| 1.3.6.1.4.1.171.10.94.89.89.26.3.1.1.1 | ColumnrsRip2IfConfAddress | read-only | current | The IP Address of this system on the indicated subnet. |
| 1.3.6.1.4.1.171.10.94.89.89.26.3.1.1.2 | ColumnrsRip2IfConfVirtualDis | read-write | current | This variable defines the virtual number of hops assigned to the interface specified by rsIfIpAddrIndex. This enables fine-tuning of the RIP routing algorithm. |
| 1.3.6.1.4.1.171.10.94.89.89.26.3.1.1.3 | ColumnrsRip2IfConfAutoSend | read-write | current | This variable controls RIP automatic send behavior. If enabled and no routers were heard on the interface, RIP will only send default route with high metric. O… |
| 1.3.6.1.4.1.171.10.94.89.89.26.3.1.1.4 | ColumnrlRip2IfConfKeyChain | read-write | current | Name of the key-chain which rip2 interface uses for md5 authentication |
| 1.3.6.1.4.1.171.10.94.89.89.26.3.2 | ScalarrlRip2AutoInterfaceCreation | read-only | current | This variable controls RIP automatic creation and activation of interfaces. If value is enable - IP interface creation results in creation and activation of ri… |
| 1.3.6.1.4.1.171.10.94.89.89.26.3.3 | ScalarrlRip2MibVersion | read-only | current | MIB's version, the current version is 1. |
| 1.3.6.1.4.1.171.10.94.89.89.26.6.1 | ScalaripRedundAdminStatus | read-write | current | This parameter controls the IP Redundancy in the device. In case the parameter is Enable and the other router becomes inoperational, all the traffic is handled… |
| 1.3.6.1.4.1.171.10.94.89.89.26.6.2 | ScalaripRedundOperStatus | read-only | current | obsolete |
| 1.3.6.1.4.1.171.10.94.89.89.26.6.3 | TableipRedundRoutersTable | not-accessible | current | List of IP addresses backed up by this router. |
| 1.3.6.1.4.1.171.10.94.89.89.26.6.3.1 | RowipRedundRoutersEntry | not-accessible | current | The row definition for this table. |
| 1.3.6.1.4.1.171.10.94.89.89.26.6.3.1.1 | ColumnipRedundRoutersIfAddr | read-only | current | The Ip address of the IP interface on which the redundancy feature is operational. |
| 1.3.6.1.4.1.171.10.94.89.89.26.6.3.1.2 | ColumnipRedundRoutersMainRouterAddr | read-only | current | The Ip address of the polled main router. |
| 1.3.6.1.4.1.171.10.94.89.89.26.6.3.1.3 | ColumnipRedundRoutersOperStatus | read-only | current | If active, the main router is considered inoperational and the IP interface operates as its backup. |
| 1.3.6.1.4.1.171.10.94.89.89.26.6.3.1.4 | ColumnipRedundRoutersPollInterval | read-write | current | Polling interval for this router (in seconds). If 0 the router is not polled. |
| 1.3.6.1.4.1.171.10.94.89.89.26.6.3.1.5 | ColumnipRedundRoutersTimeout | read-write | current | Interval in seconds during which the backed-up router must signal. If it does not signal, it is considered inoperational and the IP interface starts operating … |
| 1.3.6.1.4.1.171.10.94.89.89.26.6.3.1.6 | ColumnipRedundRoutersStatus | read-write | current | Entry status |
| 1.3.6.1.4.1.171.10.94.89.89.26.7.1 | ScalaripLeakStaticToRip | read-write | current | This parameter controls leaking (redistribution) of static routes to RIP. When enabled, all routes inserted to the IP routing table via SNMP are advertised int… |
| 1.3.6.1.4.1.171.10.94.89.89.26.7.2 | ScalaripLeakStaticToOspf | read-write | current | This parameter controls leaking (redistribution) of static routes into OSPF. When enabled, all routes inserted to the IP routing table via SNMP are advertised … |
| 1.3.6.1.4.1.171.10.94.89.89.26.7.3 | ScalaripLeakOspfToRip | read-write | current | This parameter controls leaking (redistribution) of routes from OSPF to RIP. If enabled, all routes learned via OSPF are advertised into RIP. |
| 1.3.6.1.4.1.171.10.94.89.89.26.7.4 | ScalaripLeakRipToOspf | read-write | current | This parameter controls leaking (redistribution) of routes from RIP to OSPF. If enabled, all routes learned via RIP are advertised into OSPF as external routes. |
| 1.3.6.1.4.1.171.10.94.89.89.26.7.5 | ScalaripLeakExtDirectToOspf | read-write | current | This parameter controls leaking (redistribution) into OSPF of direct routes external to OSPF, i.e. routes to local network corresponding to IP interfaces on wh… |
| 1.3.6.1.4.1.171.10.94.89.89.26.8.1 | TablersIpRipFilterGlbTable | not-accessible | current | The table of RIP global filters per IP router. |
| 1.3.6.1.4.1.171.10.94.89.89.26.8.1.1 | RowrsIpRipFilterGlbEntry | not-accessible | current | An entry in the RIP global filter table |
| 1.3.6.1.4.1.171.10.94.89.89.26.8.1.1.1 | ColumnrsIpRipFilterGlbType | read-only | current | Type of filter - input/output |
| 1.3.6.1.4.1.171.10.94.89.89.26.8.1.1.2 | ColumnrsIpRipFilterGlbNumber | read-only | current | Number of RIP filter. |
| 1.3.6.1.4.1.171.10.94.89.89.26.8.1.1.3 | ColumnrsIpRipFilterGlbStatus | read-write | current | The validity of this entry. Setting this value to invalid deletes the entry, and the entry may be actualy removed from the table. |
| 1.3.6.1.4.1.171.10.94.89.89.26.8.1.1.4 | ColumnrsIpRipFilterGlbIpAddr | read-write | current | network prefix IP address, as in the forwarding table. |
| 1.3.6.1.4.1.171.10.94.89.89.26.8.1.1.5 | ColumnrsIpRipFilterGlbNetworkMaskBits | read-write | current | the number of bits in the IP Network mask, called network-prefix-length in Router Requirements terminology. for example: the value 16 means mask 255.255.0.0 |
| 1.3.6.1.4.1.171.10.94.89.89.26.8.1.1.6 | ColumnrsIpRipFilterGlbMatchBits | read-write | current | the number of bits to match in the Network IP address. A value smaller than 32 defines a wildcard. for example: the value 8 means all routes whose leftmost 8 b… |
| 1.3.6.1.4.1.171.10.94.89.89.26.8.1.1.7 | ColumnrsIpRipFilterGlbAction | read-write | current | Filter action - permit/deny for this network |
| 1.3.6.1.4.1.171.10.94.89.89.26.8.2 | TablersIpRipFilterLclTable | not-accessible | current | Table of input/output RIP filters used per IP Interface. |
| 1.3.6.1.4.1.171.10.94.89.89.26.8.2.1 | RowrsIpRipFilterLclEntry | not-accessible | current | An entry in the Intf RIP filter table |
| 1.3.6.1.4.1.171.10.94.89.89.26.8.2.1.1 | ColumnrsIpRipFilterLclIpIntf | read-only | current | The IP address identifying the RIP interface for this filter. This value corresponds to rsIpAdEntAddr. |
| 1.3.6.1.4.1.171.10.94.89.89.26.8.2.1.2 | ColumnrsIpRipFilterLclType | read-only | current | Type of filter - input/output |
| 1.3.6.1.4.1.171.10.94.89.89.26.8.2.1.3 | ColumnrsIpRipFilterLclNumber | read-only | current | Number of RIP filter for this Interface |
| 1.3.6.1.4.1.171.10.94.89.89.26.8.2.1.4 | ColumnrsIpRipFilterLclStatus | read-write | current | The validity of this entry. Setting this value to invalid deletes the entry, and the entry may be actualy removed from the table. |
| 1.3.6.1.4.1.171.10.94.89.89.26.8.2.1.5 | ColumnrsIpRipFilterLclIpAddr | read-write | current | network prefix IP address, as in the forwarding table. |
| 1.3.6.1.4.1.171.10.94.89.89.26.8.2.1.6 | ColumnrsIpRipFilterLclNetworkMaskBits | read-write | current | the number of bits in the IP Network mask, called network-prefix-length in Router Requirements terminology. for example: the value 16 means mask 255.255.0.0 |
| 1.3.6.1.4.1.171.10.94.89.89.26.8.2.1.7 | ColumnrsIpRipFilterLclMatchBits | read-write | current | the number of bits to match in the Network IP address. A value smaller than 32 defines a wildcard. for example: the value 8 means all routes whose leftmost 8 b… |
| 1.3.6.1.4.1.171.10.94.89.89.26.8.2.1.8 | ColumnrsIpRipFilterLclAction | read-write | current | Filter action - permit/deny |
| 1.3.6.1.4.1.171.10.94.89.89.26.13.1 | ScalarrlIpRoutingProtPreferenceDirect | read-write | current | The Preference given to routes whose origin is Local IP (i.e. IP interface in IpAddrTable) It is proposed that the value will be higher than dynamic routing pr… |
| 1.3.6.1.4.1.171.10.94.89.89.26.13.2 | ScalarrlIpRoutingProtPreferenceStatic | read-write | current | The Preference given to routes whose origin is Men configured by Net managment tools, i.e. Command line or SNMP configured. |
| 1.3.6.1.4.1.171.10.94.89.89.26.13.3 | ScalarrlIpRoutingProtPreferenceOspfInter | read-write | current | The Preference given to routes whose origin is internal ospf Links. Relate to routes which are based on OSPF Link State Advertisements of type 1-4 |
| 1.3.6.1.4.1.171.10.94.89.89.26.13.4 | ScalarrlIpRoutingProtPreferenceOspfExt | read-write | current | The Preference given to routes whose origin is external to OSPF i.e. routes imported by as OSPF AS Border router. Relate to routes which are based on OSPF Link… |
| 1.3.6.1.4.1.171.10.94.89.89.26.13.5 | ScalarrlIpRoutingProtPreferenceOspfReject | read-write | current | The Preference given to routes whose origin is OSPF and Are inserted to cover gaps in net range |
| 1.3.6.1.4.1.171.10.94.89.89.26.13.6 | ScalarrlIpRoutingProtPreferenceRipNormal | read-write | current | The Preference given to routes whose origin is RIP routing domain |
| 1.3.6.1.4.1.171.10.94.89.89.26.13.7 | ScalarrlIpRoutingProtPreferenceRipAggregate | read-write | current | The Preference given to routes whose origin is aggregation As a method of rip1 to handle the CIDR schema. The idea is that ripv1 aggregates route which fall in… |
| 1.3.6.1.4.1.171.10.94.89.89.26.13.8 | ScalarrlIpRoutingProtPreferenceBgp | read-write | current | The Preference given to routes whose origin is BGP ROUTERS (EBGP or IBGP) |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.1 | ScalarrlOspfMibVersion | read-only | current | MIB's version, the current version is 1. |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.2 | ScalarrlOspfAutoInterfaceCreation | read-only | current | This variable controls OSPF automatic creation and activation of interfaces. If value is enable - IP interface creation results in creation and activation of O… |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.3 | TablerlOspfIfExtTable | not-accessible | current | The OSPF Interface Table describes the interfaces from the viewpoint of OSPF. |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.3.1 | RowrlOspfIfExtEntry | not-accessible | current | The OSPF interface table extension for md5 authentication |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.3.1.1 | ColumnrlOspfifKeyChain | read-write | current | Name of the key-chain which ospf interface uses for md5 authentication |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.4 | TablerlOspfRtrLnkTable | not-accessible | current | Router Link State Advertisement. |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.4.1 | RowrlOspfRtrLnkEntry | not-accessible | current | A single entry from Router LSA. |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.4.1.1 | ColumnrlOspfRtrLnkAreaId | read-only | current | The 32 bit identifier of the Area from which the LSA was received. |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.4.1.2 | ColumnrlOspfRtrLnkLsid | read-only | current | The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being desc… |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.4.1.3 | ColumnrlOspfRtrLnkRouterId | read-only | current | The 32 bit number that uniquely identifies the originating router in the Autonomous System. |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.4.1.4 | ColumnrlOspfRtrLnkIdx | read-only | current | The index is a unsigned 32-bit integer. It is used as sequence number of entry in the LSA and relevant only for Router or Network LSA which can contain unlimit… |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.4.1.5 | ColumnrlOspfRtrLnkSequence | read-only | current | The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linear… |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.4.1.6 | ColumnrlOspfRtrLnkAge | read-only | current | This field is the age of the link state advertisement in seconds. |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.4.1.7 | ColumnrlOspfRtrLnkChecksum | read-only | current | This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can… |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.4.1.8 | ColumnrlOspfRtrLnkLength | read-only | current | The lenth in bytes of the LSA. This includes the 20 byte LSA header. |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.4.1.9 | ColumnrlOspfRtrLnkBitV | read-only | current | When set, the router is an endpoint of one or more fully adjacent virtual links having the described area as Transit area (V is for virtual link endpoint). |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.4.1.10 | ColumnrlOspfRtrLnkBitE | read-only | current | When set, the router is an AS boundary router (E is for external). |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.4.1.11 | ColumnrlOspfRtrLnkBitB | read-only | current | When set, the router is an area border router (B is for border). |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.4.1.12 | ColumnrlOspfRtrLnkLinks | read-only | current | The number of router links described in this LSA. This must be the total collection of router links (i.e., interfaces) to the area. |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.4.1.13 | ColumnrlOspfRtrLnkLinkID | read-only | current | Identifies the object that this router link connects to. Value depends on the link's Type. |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.4.1.14 | ColumnrlOspfRtrLnkLinkData | read-only | current | Value depends on the link's Type field. |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.4.1.15 | ColumnrlOspfRtrLnkType | read-only | current | A quick description of the router link. |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.4.1.16 | ColumnrlOspfRtrLnkMetric | read-only | current | The cost of using this router link. |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.5 | TablerlOspfNetLnkTable | not-accessible | current | Network Link State Advertisement. |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.5.1 | RowrlOspfNetLnkEntry | not-accessible | current | A single entry from Network LSA. |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.5.1.1 | ColumnrlOspfNetLnkAreaId | read-only | current | The 32 bit identifier of the Area from which the LSA was received. |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.5.1.2 | ColumnrlOspfNetLnkLsid | read-only | current | The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being desc… |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.5.1.3 | ColumnrlOspfNetLnkRouterId | read-only | current | The 32 bit number that uniquely identifies the originating router in the Autonomous System. |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.5.1.4 | ColumnrlOspfNetLnkIdx | read-only | current | The index is a unsigned 32-bit integer. It is used as sequence number of entry in the LSA and relevant only for Router or Network LSA which can contain unlimit… |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.5.1.5 | ColumnrlOspfNetLnkSequence | read-only | current | The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linear… |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.5.1.6 | ColumnrlOspfNetLnkAge | read-only | current | This field is the age of the link state advertisement in seconds. |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.5.1.7 | ColumnrlOspfNetLnkChecksum | read-only | current | This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can… |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.5.1.8 | ColumnrlOspfNetLnkLength | read-only | current | The lenth in bytes of the LSA. This includes the 20 byte LSA header. |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.5.1.9 | ColumnrlOspfNetLnkMask | read-only | current | The IP address mask for the network. |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.5.1.10 | ColumnrlOspfNetLnkAttRouter | read-only | current | The Router IDs of each of the routers attached to the network. |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.6 | TablerlOspfSumLnkTable | not-accessible | current | Summary Link State Advertisement for network (Type 3). |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.6.1 | RowrlOspfSumLnkEntry | not-accessible | current | A single entry from Summary LSA. |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.6.1.1 | ColumnrlOspfSumLnkAreaId | read-only | current | The 32 bit identifier of the Area from which the LSA was received. |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.6.1.2 | ColumnrlOspfSumLnkLsid | read-only | current | The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being desc… |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.6.1.3 | ColumnrlOspfSumLnkRouterId | read-only | current | The 32 bit number that uniquely identifies the originating router in the Autonomous System. |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.6.1.4 | ColumnrlOspfSumLnkSequence | read-only | current | The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linear… |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.6.1.5 | ColumnrlOspfSumLnkAge | read-only | current | This field is the age of the link state advertisement in seconds. |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.6.1.6 | ColumnrlOspfSumLnkChecksum | read-only | current | This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can… |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.6.1.7 | ColumnrlOspfSumLnkLength | read-only | current | The lenth in bytes of the LSA. This includes the 20 byte LSA header. |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.6.1.8 | ColumnrlOspfSumLnkMask | read-only | current | Value depends on the link's Type field. |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.6.1.9 | ColumnrlOspfSumLnkMetric | read-only | current | The cost of using this router link. |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.7 | TablerlOspfAsbLnkTable | not-accessible | current | Summary Link State Advertisement for ASBR (Type 4). |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.7.1 | RowrlOspfAsbLnkEntry | not-accessible | current | A single entry from Summary LSA. |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.7.1.1 | ColumnrlOspfAsbLnkAreaId | read-only | current | The 32 bit identifier of the Area from which the LSA was received. |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.7.1.2 | ColumnrlOspfAsbLnkLsid | read-only | current | The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being desc… |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.7.1.3 | ColumnrlOspfAsbLnkRouterId | read-only | current | The 32 bit number that uniquely identifies the originating router in the Autonomous System. |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.7.1.4 | ColumnrlOspfAsbLnkSequence | read-only | current | The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linear… |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.7.1.5 | ColumnrlOspfAsbLnkAge | read-only | current | This field is the age of the link state advertisement in seconds. |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.7.1.6 | ColumnrlOspfAsbLnkChecksum | read-only | current | This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can… |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.7.1.7 | ColumnrlOspfAsbLnkLength | read-only | current | The lenth in bytes of the LSA. This includes the 20 byte LSA header. |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.7.1.8 | ColumnrlOspfAsbLnkMetric | read-only | current | The cost of using this router link. |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.8 | TablerlOspfAseLnkTable | not-accessible | current | External Link State Advertisement. |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.8.1 | RowrlOspfAseLnkEntry | not-accessible | current | A single entry from External LSA. |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.8.1.1 | ColumnrlOspfAseLnkLsid | read-only | current | The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being desc… |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.8.1.2 | ColumnrlOspfAseLnkRouterId | read-only | current | The 32 bit number that uniquely identifies the originating router in the Autonomous System. |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.8.1.3 | ColumnrlOspfAseLnkSequence | read-only | current | The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linear… |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.8.1.4 | ColumnrlOspfAseLnkAge | read-only | current | This field is the age of the link state advertisement in seconds. |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.8.1.5 | ColumnrlOspfAseLnkChecksum | read-only | current | This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can… |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.8.1.6 | ColumnrlOspfAseLnkLength | read-only | current | The lenth in bytes of the LSA. This includes the 20 byte LSA header. |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.8.1.7 | ColumnrlOspfAseLnkMask | read-only | current | Value depends on the link's Type field. |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.8.1.8 | ColumnrlOspfAseLnkFrwAddress | read-only | current | Data traffic for the advertised destination will be forwarded to this address. If the Forwarding address is set to 0.0.0.0, data traffic will be forwarded inst… |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.8.1.9 | ColumnrlOspfAseLnkBitE | read-only | current | The type of external metric. If bit E is set, the metric specified is a Type 2 external metric. |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.8.1.10 | ColumnrlOspfAseLnkMetric | read-only | current | The cost of this route. |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.8.1.11 | ColumnrlOspfAseLnkTag | read-only | current | A 32-bit field attached to each external route. |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.9 | TablerlospfVirtIfExtTable | not-accessible | current | The Virtual Interface Table describes the virtual links that the OSPF Process is configured to carry on. |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.9.1 | RowrlospfVirtIfExtEntry | not-accessible | current | The OSPF virtual interface table extension for md5 authentication |
| 1.3.6.1.4.1.171.10.94.89.89.26.14.9.1.1 | ColumnrlospfVirtifKeyChain | read-write | current | Name of the key-chain which ospf virtual interface uses for md5 authentication |
| 1.3.6.1.4.1.171.10.94.89.89.26.18 | IdentityrlIpRouter | The private MIB module definition for RND router MIB. |