DLINKSW-POE-MIB
54 objects
A MIB module for extending POWER-ETHERNET-MIB specified in RFC 3621.
Imported Objects
| DLINK-ID-REC-MIB | dlinkIndustrialCommon |
| INET-ADDRESS-MIB | InetAddress InetAddressType |
| POWER-ETHERNET-MIB | pethMainPseGroupIndex pethPsePortIndex pethPsePortOverLoadCounter pethPsePortPowerDeniedCounter pethPsePortShortCounter |
| Q-BRIDGE-MIB | PortList |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DisplayString TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.171.14.24 | IdentitydlinkSwPoeExtMIB | A MIB module for extending POWER-ETHERNET-MIB specified in RFC 3621. | ||
| 1.3.6.1.4.1.171.14.24.0 | NodedPoeMIBNotifications | |||
| 1.3.6.1.4.1.171.14.24.0.1 | NotificationdPoeIfPowerDeniedNotification | current | This Notification indicates if PSE state diagram enters the state POWER_DENIED. At least 500 msec must elapse between notifications being emitted by the same o… | |
| 1.3.6.1.4.1.171.14.24.0.2 | NotificationdPoeIfPowerOverLoadNotification | current | This Notification indicates if PSE state diagram enters the state ERROR_DELAY_OVER. At least 500 msec must elapse between notifications being emitted by the sa… | |
| 1.3.6.1.4.1.171.14.24.0.3 | NotificationdPoeIfPowerShortCircuitNotification | current | This Notification indicates if PSE state diagram enters the state ERROR_DELAY_SHORT. At least 500 msec must elapse between notifications being emitted by the s… | |
| 1.3.6.1.4.1.171.14.24.0.4 | NotificationdPoeIfPdAliveFailOccurNotification | current | This Notification indicates if the PD device has the stop working or no response problem. | |
| 1.3.6.1.4.1.171.14.24.1 | NodedPoeMIBObjects | |||
| 1.3.6.1.4.1.171.14.24.1.1 | TabledPoeGroupCfgTable | not-accessible | current | This table consists of a list of group configurations for PoE. Group means box in the stack or module in a rack. For non-modular devices, the pethMainPseGroupI… |
| 1.3.6.1.4.1.171.14.24.1.1.1 | RowdPoeGroupCfgEntry | not-accessible | current | An entry contains the system configuration of the PoE on a group. |
| 1.3.6.1.4.1.171.14.24.1.1.1.1 | ColumndPoeGroupPolicyPreempt | read-write | current | This object configures whether to disconnect the PD which is powered with lower priority in order to release the power to the new connected PD with higher prio… |
| 1.3.6.1.4.1.171.14.24.1.1.1.2 | ColumndPoeGroupClearIfStatistic | read-write | current | This object is used to clear the PoE statistics of pethPsePortEntry for specified ports. |
| 1.3.6.1.4.1.171.14.24.1.1.1.3 | ColumndPoeGroupIfLedMode | read-write | current | For some devices,port LED can indicate either poe status or link status. This object is used to configure or display port LED mode. poeMode(1) - indicates poe … |
| 1.3.6.1.4.1.171.14.24.1.2 | TabledPoeGroupInfoTable | not-accessible | current | This table consists of a list of PoE information for groups. |
| 1.3.6.1.4.1.171.14.24.1.2.1 | RowdPoeGroupInfoEntry | not-accessible | current | An entry contains the system information of the PoE on a group. |
| 1.3.6.1.4.1.171.14.24.1.2.1.1 | ColumndPoeGroupMaxPorts | read-only | current | This object indicates the maximum number of ports that the group can support. |
| 1.3.6.1.4.1.171.14.24.1.2.1.2 | ColumndPoeGroupHWVersion | read-only | current | This object indicates H/W version of PoE chip. |
| 1.3.6.1.4.1.171.14.24.1.2.1.3 | ColumndPoeGroupSWVersion | read-only | current | This object indicates firmware version of PoE chip. |
| 1.3.6.1.4.1.171.14.24.1.3 | NodedPoeIfObjects | |||
| 1.3.6.1.4.1.171.14.24.1.3.1 | TabledPoeIfCfgTable | not-accessible | current | This table consists of a list of PoE configuration information for ports. |
| 1.3.6.1.4.1.171.14.24.1.3.1.1 | RowdPoeIfCfgEntry | not-accessible | current | An entry contains PoE configuration on a port. |
| 1.3.6.1.4.1.171.14.24.1.3.1.1.1 | ColumndPoeIfState | read-write | current | This object indicates the PoE state of the entry. auto(1) - the port will automatically detect the PD and provision power to the PD. The max wattage value whic… |
| 1.3.6.1.4.1.171.14.24.1.3.1.1.2 | ColumndPoeIfMaxPower | read-write | current | This object indicates the max wattage value which can be provisioned to the port. Note: This object is valid only while the dPoeIfState object is configured as… |
| 1.3.6.1.4.1.171.14.24.1.3.1.1.3 | ColumndPoeIfTimeRange | read-write | current | This object indicates the name of time-range profile to delineate the activation period. A zero length string indicates the time-range is not specified. Note: … |
| 1.3.6.1.4.1.171.14.24.1.3.1.1.4 | ColumndPoeIfLegacyPdEnabled | read-write | current | This object indicates the state of legacy PD support. |
| 1.3.6.1.4.1.171.14.24.1.3.2 | NodedPoeIfInfoObjects | |||
| 1.3.6.1.4.1.171.14.24.1.3.2.1 | TabledPoeIfStatusTable | not-accessible | current | This table consists of a list of PoE status for ports. |
| 1.3.6.1.4.1.171.14.24.1.3.2.1.1 | RowdPoeIfStatusEntry | not-accessible | current | An entry consists of PoE status for a port. |
| 1.3.6.1.4.1.171.14.24.1.3.2.1.1.1 | ColumndPoeIfDetectStatus | read-only | current | This object indicates the operational status of the port PD detection. disabled(1) - PSE function is disabled. searching(2) - Remote PD is not connected. reque… |
| 1.3.6.1.4.1.171.14.24.1.3.2.1.1.2 | ColumndPoeIfFaultyType | read-only | current | This object indicates the specific faulty type. It is meaningful only when dPoeIfDetectStatus object is 'faulty'. notApplicable(0) - indicates this object is m… |
| 1.3.6.1.4.1.171.14.24.1.3.2.2 | TabledPoeIfMeasurementTable | not-accessible | current | This table consists of a list of POE measurement information for ports. |
| 1.3.6.1.4.1.171.14.24.1.3.2.2.1 | RowdPoeIfMeasurementEntry | not-accessible | current | An entry consists of PoE measurement information of a port. |
| 1.3.6.1.4.1.171.14.24.1.3.2.2.1.1 | ColumndPoeIfVoltage | read-only | current | This object indicates the voltage of the port in millivolts. |
| 1.3.6.1.4.1.171.14.24.1.3.2.2.1.2 | ColumndPoeIfCurrent | read-only | current | This object indicates the current of port in milliamperes. |
| 1.3.6.1.4.1.171.14.24.1.3.2.2.1.3 | ColumndPoeIfTemperature | read-only | current | This object indicates the temperature of port in degrees centigrade. |
| 1.3.6.1.4.1.171.14.24.1.3.2.2.1.4 | ColumndPoeIfPower | read-only | current | This object indicates consumption power of port in milliwatts. |
| 1.3.6.1.4.1.171.14.24.1.3.3 | TabledPoeIfPdAliveCfgTable | not-accessible | current | This table consists of a list of configuration for the PD alive check function for ports. The PD alive check feature provides the solution for PD device that h… |
| 1.3.6.1.4.1.171.14.24.1.3.3.1 | RowdPoeIfPdAliveCfgEntry | not-accessible | current | An entry contains configuration for PD alive check on a port. |
| 1.3.6.1.4.1.171.14.24.1.3.3.1.1 | ColumndPoeIfPdAliveCfgState | read-write | current | This object indicates the the PD alive function sate. enabled - Enable the PD alive check function disabled - Disable the PD alive check function. |
| 1.3.6.1.4.1.171.14.24.1.3.3.1.2 | ColumndPoeIfPdAliveCfgPdIpType | read-write | current | This object indicates the IP address type of the target PD. |
| 1.3.6.1.4.1.171.14.24.1.3.3.1.3 | ColumndPoeIfPdAliveCfgPdIpAddr | read-write | current | This object indicates the IP address of the target PD. |
| 1.3.6.1.4.1.171.14.24.1.3.3.1.4 | ColumndPoeIfPdAliveCfgInterval | read-write | current | This object indicates the time interval for system issues ping request to detect the target PD. The valid range for interval time is 10s to 300s. |
| 1.3.6.1.4.1.171.14.24.1.3.3.1.5 | ColumndPoeIfPdAliveCfgRetry | read-write | current | This object indicates the retry count of ping request when PD has no response. The valid range for retry count is 0 to 5 times. |
| 1.3.6.1.4.1.171.14.24.1.3.3.1.6 | ColumndPoeIfPdAliveCfgWaitTime | read-write | current | This object indicates the waiting time for PD reboot. The valid range for waiting time is 30s to 300s. |
| 1.3.6.1.4.1.171.14.24.1.3.3.1.7 | ColumndPoeIfPdAliveCfgAction | read-write | current | This object indicates the action when PD doesn't reply the ping request. reset- System will reset the PoE port state . notify- System will send log and trap to… |
| 1.3.6.1.4.1.171.14.24.2 | NodedPoeMIBConformance | |||
| 1.3.6.1.4.1.171.14.24.2.1 | NodedPoeMIBCompliances | |||
| 1.3.6.1.4.1.171.14.24.2.1.1 | CompliancedPoeMIBCompliance | current | The compliance statement for entities which implement the DLINKSW-POE-MIB. | |
| 1.3.6.1.4.1.171.14.24.2.2 | NodedPoeMIBGroups | |||
| 1.3.6.1.4.1.171.14.24.2.2.1 | GroupdPoeGroupCfgGroup | current | A collection of objects to configure or display the group-specific PoE information. | |
| 1.3.6.1.4.1.171.14.24.2.2.2 | GroupdPoeIfCfgGroup | current | A collection of objects configure or display the ports information. | |
| 1.3.6.1.4.1.171.14.24.2.2.3 | GroupdPoeGroupInfoGroup | current | A collection of objects display the groups information. | |
| 1.3.6.1.4.1.171.14.24.2.2.4 | GroupdPoeIfInfoGroup | current | A collection of objects display the ports information. | |
| 1.3.6.1.4.1.171.14.24.2.2.5 | GroupdPoeIfErrorStateNotificationGroup | current | A collection of objects provides ports error state notifications. | |
| 1.3.6.1.4.1.171.14.24.2.2.6 | GroupdPoeIfPdAliveCfgGroup | current | A collection of objects display the PD alive check configuration. |