MIB Viewer

DOCS-QOS-MIB

169 objects
This is the management information for Quality Of Service (QOS) for DOCSIS 1.1.
Imported Objects
DOCS-IF-MIBdocsIfMib
IF-MIBifIndex InterfaceIndex
SNMPv2-CONFMODULE-COMPLIANCE OBJECT-GROUP
SNMPv2-SMICounter32 Integer32 IpAddress MODULE-IDENTITY OBJECT-TYPE Unsigned32
SNMPv2-TCDisplayString MacAddress RowStatus TEXTUAL-CONVENTION TimeStamp TruthValue
OIDNameAccessStatusDescription
1.3.6.1.2.1.10.127.7IdentitydocsQosMIBThis is the management information for Quality Of Service (QOS) for DOCSIS 1.1.
1.3.6.1.2.1.10.127.7.1NodedocsQosMIBObjects
1.3.6.1.2.1.10.127.7.1.1TabledocsQosPktClassTablenot-accessiblecurrentThis table describes the packet classification configured on the CM or CMTS. The model is that a packet either received as input from an interface or transmitt…
1.3.6.1.2.1.10.127.7.1.1.1RowdocsQosPktClassEntrynot-accessiblecurrentAn entry in this table provides a single packet classifier rule. The index ifIndex is an ifType of docsCableMaclayer(127).
1.3.6.1.2.1.10.127.7.1.1.1.1ColumndocsQosPktClassIdnot-accessiblecurrentIndex assigned to packet classifier entry by the CMTS which is unique per service flow.
1.3.6.1.2.1.10.127.7.1.1.1.2ColumndocsQosPktClassDirectionread-onlycurrentIndicates the direction to which the classifier is applied.
1.3.6.1.2.1.10.127.7.1.1.1.3ColumndocsQosPktClassPriorityread-onlycurrentThe value specifies the order of evaluation of the classifiers. The higher the value the higher the priority. The value of 0 is used as default in provisioned …
1.3.6.1.2.1.10.127.7.1.1.1.4ColumndocsQosPktClassIpTosLowread-onlycurrentThe low value of a range of TOS byte values. If the referenced parameter is not present in a classifier, this object reports the value of 0.
1.3.6.1.2.1.10.127.7.1.1.1.5ColumndocsQosPktClassIpTosHighread-onlycurrentThe 8-bit high value of a range of TOS byte values. If the referenced parameter is not present in a classifier, this object reports the value of 0.
1.3.6.1.2.1.10.127.7.1.1.1.6ColumndocsQosPktClassIpTosMaskread-onlycurrentThe mask value is bitwise ANDed with TOS byte in an IP packet and this value is used check range checking of TosLow and TosHigh. If the referenced parameter is…
1.3.6.1.2.1.10.127.7.1.1.1.7ColumndocsQosPktClassIpProtocolread-onlycurrentThis object indicates the value of the IP Protocol field required for IP packets to match this rule. The value 256 matches traffic with any IP Protocol value. …
1.3.6.1.2.1.10.127.7.1.1.1.8ColumndocsQosPktClassIpSourceAddrread-onlycurrentThis object specifies the value of the IP Source Address required for packets to match this rule. An IP packet matches the rule when the packet ip source addre…
1.3.6.1.2.1.10.127.7.1.1.1.9ColumndocsQosPktClassIpSourceMaskread-onlycurrentThis object specifies which bits of a packet's IP Source Address that are compared to match this rule. An IP packet matches the rule when the packet source add…
1.3.6.1.2.1.10.127.7.1.1.1.10ColumndocsQosPktClassIpDestAddrread-onlycurrentThis object specifies the value of the IP Destination Address required for packets to match this rule. An IP packet matches the rule when the packet IP destina…
1.3.6.1.2.1.10.127.7.1.1.1.11ColumndocsQosPktClassIpDestMaskread-onlycurrentThis object specifies which bits of a packet's IP Destination Address that are compared to match this rule. An IP packet matches the rule when the packet desti…
1.3.6.1.2.1.10.127.7.1.1.1.12ColumndocsQosPktClassSourcePortStartread-onlycurrentThis object specifies the low end inclusive range of TCP/UDP source port numbers to which a packet is compared. This object is irrelevant for non-TCP/UDP IP pa…
1.3.6.1.2.1.10.127.7.1.1.1.13ColumndocsQosPktClassSourcePortEndread-onlycurrentThis object specifies the high end inclusive range of TCP/UDP source port numbers to which a packet is compared. This object is irrelevant for non-TCP/UDP IP p…
1.3.6.1.2.1.10.127.7.1.1.1.14ColumndocsQosPktClassDestPortStartread-onlycurrentThis object specifies the low end inclusive range of TCP/UDP destination port numbers to which a packet is compared. If the referenced parameter is not present…
1.3.6.1.2.1.10.127.7.1.1.1.15ColumndocsQosPktClassDestPortEndread-onlycurrentThis object specifies the high end inclusive range of TCP/UDP destination port numbers to which a packet is compared. If the referenced parameter is not presen…
1.3.6.1.2.1.10.127.7.1.1.1.16ColumndocsQosPktClassDestMacAddrread-onlycurrentAn Ethernet packet matches an entry when its destination MAC address bitwise ANDed with docsQosPktClassDestMacMask equals the value of docsQosPktClassDestMacAd…
1.3.6.1.2.1.10.127.7.1.1.1.17ColumndocsQosPktClassDestMacMaskread-onlycurrentAn Ethernet packet matches an entry when its destination MAC address bitwise ANDed with docsQosPktClassDestMacMask equals the value of docsQosPktClassDestMacAd…
1.3.6.1.2.1.10.127.7.1.1.1.18ColumndocsQosPktClassSourceMacAddrread-onlycurrentAn Ethernet packet matches this entry when its source MAC address equals the value of this object. If the referenced parameter is not present in a classifier, …
1.3.6.1.2.1.10.127.7.1.1.1.19ColumndocsQosPktClassEnetProtocolTyperead-onlycurrentThis object indicates the format of the layer 3 protocol id in the Ethernet packet. A value of none(0) means that the rule does not use the layer 3 protocol ty…
1.3.6.1.2.1.10.127.7.1.1.1.20ColumndocsQosPktClassEnetProtocolread-onlycurrentIf docsQosEthPktClassProtocolType is none(0), this object is ignored when considering whether a packet matches the current rule. If dosQosPktClassEnetProtocolT…
1.3.6.1.2.1.10.127.7.1.1.1.22ColumndocsQosPktClassUserPriLowread-onlycurrentThis object applies only to Ethernet frames using the 802.1P/Q tag header (indicated with EtherType 0x8100). Such frames include a 16-bit Tag that contains a 3…
1.3.6.1.2.1.10.127.7.1.1.1.23ColumndocsQosPktClassUserPriHighread-onlycurrentThis object applies only to Ethernet frames using the 802.1P/Qtag header (indicated with EtherType 0x8100). Such frames include a 16-bit Tag that contains a 3 …
1.3.6.1.2.1.10.127.7.1.1.1.24ColumndocsQosPktClassVlanIdread-onlycurrentThis object applies only to Ethernet frames using the 802.1P/Q tag header. If this object's value is nonzero, tagged packets must have a VLAN Identifier that m…
1.3.6.1.2.1.10.127.7.1.1.1.25ColumndocsQosPktClassStateread-onlycurrentThis object indicates whether or not the classifier is enabled to classify packets to a Service Flow. If the referenced parameter is not present in the classif…
1.3.6.1.2.1.10.127.7.1.1.1.26ColumndocsQosPktClassPktsread-onlycurrentThis object counts the number of packets that have been classified using this entry.
1.3.6.1.2.1.10.127.7.1.1.1.27ColumndocsQosPktClassBitMapread-onlycurrentThis object indicates which parameter encodings were actually present in the DOCSIS packet classifier encoding signalled in the DOCSIS message that created the…
1.3.6.1.2.1.10.127.7.1.2TabledocsQosParamSetTablenot-accessiblecurrentThis table describes the set of DOCSIS 1.1 QOS parameters defined in a managed device. The ifIndex index specifies a DOCSIS MAC Domain. The docsQosServiceFlowI…
1.3.6.1.2.1.10.127.7.1.2.2RowdocsQosParamSetEntrynot-accessiblecurrentA unique set of QOS parameters.
1.3.6.1.2.1.10.127.7.1.2.2.4ColumndocsQosParamSetServiceClassNameread-onlycurrentRefers to the Service Class Name that the parameter set values were derived. If the referenced parameter is not present in the corresponding DOCSIS QOS Paramet…
1.3.6.1.2.1.10.127.7.1.2.2.5ColumndocsQosParamSetPriorityread-onlycurrentThe relative priority of a service flow. Higher numbers indicate higher priority. This priority should only be used to differentiate service flow with identica…
1.3.6.1.2.1.10.127.7.1.2.2.6ColumndocsQosParamSetMaxTrafficRateread-onlycurrentMaximum sustained traffic rate allowed for this service flow in bits/sec. Must count all MAC frame data PDU from the bytes following the MAC header HCS to the …
1.3.6.1.2.1.10.127.7.1.2.2.7ColumndocsQosParamSetMaxTrafficBurstread-onlycurrentSpecifies the token bucket size in bytes for this parameter set. The value is calculated from the byte following the MAC header HCS to the end of the CRC. This…
1.3.6.1.2.1.10.127.7.1.2.2.8ColumndocsQosParamSetMinReservedRateread-onlycurrentSpecifies the guaranteed minimum rate in bits/sec for this parameter set. The value is calculated from the byte following the MAC header HCS to the end of the …
1.3.6.1.2.1.10.127.7.1.2.2.9ColumndocsQosParamSetMinReservedPktread-onlycurrentSpecifies an assumed minimum packet size in bytes for which the docsQosParamSetMinReservedRate will be provided. The value is calculated from the byte followin…
1.3.6.1.2.1.10.127.7.1.2.2.10ColumndocsQosParamSetActiveTimeoutread-onlycurrentSpecifies the maximum duration in seconds that resources remain unused on an active service flow before CMTS signals that both active and admitted parameters s…
1.3.6.1.2.1.10.127.7.1.2.2.11ColumndocsQosParamSetAdmittedTimeoutread-onlycurrentSpecifies the maximum duration in seconds that resources remain in admitted state before resources must be released. The value of 0 signifies an infinite amoun…
1.3.6.1.2.1.10.127.7.1.2.2.12ColumndocsQosParamSetMaxConcatBurstread-onlycurrentSpecifies the maximum concatenated burst in bytes which an upstream service flow is allowed. The value is calculated from the FC byte of the Concatenation MAC …
1.3.6.1.2.1.10.127.7.1.2.2.13ColumndocsQosParamSetSchedulingTyperead-onlycurrentSpecifies the upstream scheduling service used for upstream service flow. If the referenced parameter is not present in the corresponding DOCSIS QOS Parameter …
1.3.6.1.2.1.10.127.7.1.2.2.15ColumndocsQosParamSetNomPollIntervalread-onlycurrentSpecifies the nominal interval in microseconds between successive unicast request opportunities on an upstream service flow. This object applies only to upstre…
1.3.6.1.2.1.10.127.7.1.2.2.16ColumndocsQosParamSetTolPollJitterread-onlycurrentSpecifies the maximum amount of time in microseconds that the unicast request interval may be delayed from the nominal periodic schedule on an upstream service…
1.3.6.1.2.1.10.127.7.1.2.2.17ColumndocsQosParamSetUnsolicitGrantSizeread-onlycurrentSpecifies the unsolicited grant size in bytes. The grant size includes the entired MAC frame data PDU from the Frame Control byte to end of the MAC frame. The …
1.3.6.1.2.1.10.127.7.1.2.2.18ColumndocsQosParamSetNomGrantIntervalread-onlycurrentSpecifies the nominal interval in microseconds between successive data grant opportunities on an upstream service flow. The referenced parameter is applicable …
1.3.6.1.2.1.10.127.7.1.2.2.19ColumndocsQosParamSetTolGrantJitterread-onlycurrentSpecifies the maximum amount of time in microseconds that the transmission opportunities may be delayed from the nominal periodic schedule. The referenced para…
1.3.6.1.2.1.10.127.7.1.2.2.20ColumndocsQosParamSetGrantsPerIntervalread-onlycurrentSpecifies the number of data grants per Nominal Grant Interval (docsQosParamSetNomGrantInterval). The referenced parameter is applicable only for upstream flow…
1.3.6.1.2.1.10.127.7.1.2.2.21ColumndocsQosParamSetTosAndMaskread-onlycurrentSpecifies the AND mask for IP TOS byte for overwriting IP packets TOS value. The IP packets TOS byte is bitwise ANDed with docsQosParamSetTosAndMask and result…
1.3.6.1.2.1.10.127.7.1.2.2.22ColumndocsQosParamSetTosOrMaskread-onlycurrentSpecifies the OR mask for IP TOS byte. See the description of docsQosParamSetTosAndMask for further details.
1.3.6.1.2.1.10.127.7.1.2.2.23ColumndocsQosParamSetMaxLatencyread-onlycurrentSpecifies the maximum latency between the reception of a packet by the CMTS on its NSI and the forwarding of the packet to the RF interface. A value of 0 signi…
1.3.6.1.2.1.10.127.7.1.2.2.24ColumndocsQosParamSetTypenot-accessiblecurrentDefines the type of the QOS parameter set defined by this row. active(1) indicates the Active QOS parameter set, describing the service currently being provide…
1.3.6.1.2.1.10.127.7.1.2.2.25ColumndocsQosParamSetRequestPolicyOctread-onlycurrentSpecifies which transmit interval opportunities the CM omits for upstream transmission requests and packet transmissions. This object takes its default value f…
1.3.6.1.2.1.10.127.7.1.2.2.26ColumndocsQosParamSetBitMapread-onlycurrentThis object indicates the set of QOS Parameter Set parameters actually signaled in the DOCSIS registration or dynamic service request message that created the …
1.3.6.1.2.1.10.127.7.1.3TabledocsQosServiceFlowTablenot-accessiblecurrentThis table describes the set of Docsis-QOS Service Flows in a managed device.
1.3.6.1.2.1.10.127.7.1.3.1RowdocsQosServiceFlowEntrynot-accessiblecurrentDescribes a service flow. An entry in the table exists for each Service Flow ID. The ifIndex is an ifType of docsCableMaclayer(127).
1.3.6.1.2.1.10.127.7.1.3.1.1ColumndocsQosServiceFlowIdnot-accessiblecurrentAn index assigned to a service flow by CMTS.
1.3.6.1.2.1.10.127.7.1.3.1.6ColumndocsQosServiceFlowSIDread-onlycurrentService Identifier (SID) assigned to an admitted or active service flow. This object reports a value of 0 if a Service Id is not associated with the service fl…
1.3.6.1.2.1.10.127.7.1.3.1.7ColumndocsQosServiceFlowDirectionread-onlycurrentThe direction of the service flow.
1.3.6.1.2.1.10.127.7.1.3.1.8ColumndocsQosServiceFlowPrimaryread-onlycurrentObject reflects whether service flow is the primary or a secondary service flow. A primary service flow is the default service flow for otherwise unclassified …
1.3.6.1.2.1.10.127.7.1.4TabledocsQosServiceFlowStatsTablenot-accessiblecurrentThis table describes statistics associated with the Service Flows in a managed device.
1.3.6.1.2.1.10.127.7.1.4.1RowdocsQosServiceFlowStatsEntrynot-accessiblecurrentDescribes a set of service flow statistics. An entry in the table exists for each Service Flow ID. The ifIndex is an ifType of docsCableMaclayer(127).
1.3.6.1.2.1.10.127.7.1.4.1.1ColumndocsQosServiceFlowPktsread-onlycurrentThe number of packet counted on this service flow.
1.3.6.1.2.1.10.127.7.1.4.1.2ColumndocsQosServiceFlowOctetsread-onlycurrentThe number of octets counted on this service flow after payload header suppression.
1.3.6.1.2.1.10.127.7.1.4.1.3ColumndocsQosServiceFlowTimeCreatedread-onlycurrentThe value of sysUpTime when the service flow was created.
1.3.6.1.2.1.10.127.7.1.4.1.4ColumndocsQosServiceFlowTimeActiveread-onlycurrentThe total time that service flow has been active.
1.3.6.1.2.1.10.127.7.1.4.1.5ColumndocsQosServiceFlowPHSUnknownsread-onlycurrentThe number of packet with unknown payload header suppression index.
1.3.6.1.2.1.10.127.7.1.4.1.6ColumndocsQosServiceFlowPolicedDropPktsread-onlycurrentThe number of packets dropped due to policing of the service flow, especially to limit the maximum rate of the flow.
1.3.6.1.2.1.10.127.7.1.4.1.7ColumndocsQosServiceFlowPolicedDelayPktsread-onlycurrentThe number of packet delayed due to policing of the service flow, especially to limit the maximum rate of the flow.
1.3.6.1.2.1.10.127.7.1.5TabledocsQosUpstreamStatsTablenot-accessiblecurrentThis table describes statistics associated with upstream service flows. All counted frames must be received without an FCS error.
1.3.6.1.2.1.10.127.7.1.5.1RowdocsQosUpstreamStatsEntrynot-accessiblecurrentDescribes a set of upstream service flow statistics. An entry in the table exists for each upstream Service Flow in a managed device. The ifIndex is an ifType …
1.3.6.1.2.1.10.127.7.1.5.1.1ColumndocsQosSIDnot-accessiblecurrentIdentifies a service id for an admitted or active upstream service flow.
1.3.6.1.2.1.10.127.7.1.5.1.2ColumndocsQosUpstreamFragmentsread-onlycurrentThe number of fragmentation headers received on an upstream service flow, regardless of whether the fragment was correctly reassembled into a valid packet.
1.3.6.1.2.1.10.127.7.1.5.1.3ColumndocsQosUpstreamFragDiscardsread-onlycurrentThe number of upstream fragments discarded and not assembled into a valid upstream packet.
1.3.6.1.2.1.10.127.7.1.5.1.4ColumndocsQosUpstreamConcatBurstsread-onlycurrentThe number of concatenation headers received on an upstream service flow.
1.3.6.1.2.1.10.127.7.1.6TabledocsQosDynamicServiceStatsTablenot-accessiblecurrentThis table describes statistics associated with the Dynamic Service Flows in a managed device.
1.3.6.1.2.1.10.127.7.1.6.1RowdocsQosDynamicServiceStatsEntrynot-accessiblecurrentDescribes a set of dynamic service flow statistics. Two entries exist for each Docsis mac layer interface for the upstream and downstream direction. On the CMT…
1.3.6.1.2.1.10.127.7.1.6.1.1ColumndocsQosIfDirectionnot-accessiblecurrentThe direction of interface.
1.3.6.1.2.1.10.127.7.1.6.1.2ColumndocsQosDSAReqsread-onlycurrentThe number of Dynamic Service Addition Requests
1.3.6.1.2.1.10.127.7.1.6.1.3ColumndocsQosDSARspsread-onlycurrentThe number of Dynamic Service Addition Responses
1.3.6.1.2.1.10.127.7.1.6.1.4ColumndocsQosDSAAcksread-onlycurrentThe number of Dynamic Service Addition Acknowledgements.
1.3.6.1.2.1.10.127.7.1.6.1.5ColumndocsQosDSCReqsread-onlycurrentThe number of Dynamic Service Change Requests
1.3.6.1.2.1.10.127.7.1.6.1.6ColumndocsQosDSCRspsread-onlycurrentThe number of Dynamic Service Change Responses
1.3.6.1.2.1.10.127.7.1.6.1.7ColumndocsQosDSCAcksread-onlycurrentThe number of Dynamic Service Change Acknowlegements.
1.3.6.1.2.1.10.127.7.1.6.1.8ColumndocsQosDSDReqsread-onlycurrentThe number of Dynamic Service Delete Requests
1.3.6.1.2.1.10.127.7.1.6.1.9ColumndocsQosDSDRspsread-onlycurrentThe number of Dynamic Service Delete Responses
1.3.6.1.2.1.10.127.7.1.6.1.10ColumndocsQosDynamicAddsread-onlycurrentThe number of successful Dynamic Service Addition transactions.
1.3.6.1.2.1.10.127.7.1.6.1.11ColumndocsQosDynamicAddFailsread-onlycurrentThe number of failed Dynamic Service Addition transactions.
1.3.6.1.2.1.10.127.7.1.6.1.12ColumndocsQosDynamicChangesread-onlycurrentThe number of successful Dynamic Service Change transactions.
1.3.6.1.2.1.10.127.7.1.6.1.13ColumndocsQosDynamicChangeFailsread-onlycurrentThe number of failed Dynamic Service Change transactions.
1.3.6.1.2.1.10.127.7.1.6.1.14ColumndocsQosDynamicDeletesread-onlycurrentThe number of successful Dynamic Service Delete transactions.
1.3.6.1.2.1.10.127.7.1.6.1.15ColumndocsQosDynamicDeleteFailsread-onlycurrentThe number of failed Dynamic Service Delete transactions.
1.3.6.1.2.1.10.127.7.1.6.1.16ColumndocsQosDCCReqsread-onlycurrentThe number of Dynamic Channel Change Request messages traversing an interface. This count is nonzero only on downstream direction rows.
1.3.6.1.2.1.10.127.7.1.6.1.17ColumndocsQosDCCRspsread-onlycurrentThe number of Dynamic Channel Change Response messages traversing an interface. This count is nonzero only on upstream direction rows.
1.3.6.1.2.1.10.127.7.1.6.1.18ColumndocsQosDCCAcksread-onlycurrentThe number of Dynamic Channel Change Acknowledgement messages traversing an interface. This count is nonzero only on downstream direction rows.
1.3.6.1.2.1.10.127.7.1.6.1.19ColumndocsQosDCCsread-onlycurrentThe number of successful Dynamic Channel Change transactions. This count is nonzero only on downstream direction rows.
1.3.6.1.2.1.10.127.7.1.6.1.20ColumndocsQosDCCFailsread-onlycurrentThe number of failed Dynamic Channel Change transactions. This count is nonzero only on downstream direction rows.
1.3.6.1.2.1.10.127.7.1.7TabledocsQosServiceFlowLogTablenot-accessiblecurrentThis table contains a log of the disconnected Service Flows in a managed device.
1.3.6.1.2.1.10.127.7.1.7.1RowdocsQosServiceFlowLogEntrynot-accessiblecurrentThe information regarding a single disconnected service flow.
1.3.6.1.2.1.10.127.7.1.7.1.1ColumndocsQosServiceFlowLogIndexnot-accessiblecurrentUnique index for a logged service flow.
1.3.6.1.2.1.10.127.7.1.7.1.2ColumndocsQosServiceFlowLogIfIndexread-onlycurrentThe ifIndex of ifType docsCableMacLayter(127) on the CMTS where the service flow was present.
1.3.6.1.2.1.10.127.7.1.7.1.3ColumndocsQosServiceFlowLogSFIDread-onlycurrentThe index assigned to the service flow by the CMTS.
1.3.6.1.2.1.10.127.7.1.7.1.4ColumndocsQosServiceFlowLogCmMacread-onlycurrentThe MAC address for the cable modem associated with the service flow.
1.3.6.1.2.1.10.127.7.1.7.1.5ColumndocsQosServiceFlowLogPktsread-onlycurrentThe number of packets counted on this service flow after payload header suppression.
1.3.6.1.2.1.10.127.7.1.7.1.6ColumndocsQosServiceFlowLogOctetsread-onlycurrentThe number of octets counted on this service flow after payload header suppression.
1.3.6.1.2.1.10.127.7.1.7.1.7ColumndocsQosServiceFlowLogTimeDeletedread-onlycurrentThe value of sysUpTime when the service flow was deleted.
1.3.6.1.2.1.10.127.7.1.7.1.8ColumndocsQosServiceFlowLogTimeCreatedread-onlycurrentThe value of sysUpTime when the service flow was created.
1.3.6.1.2.1.10.127.7.1.7.1.9ColumndocsQosServiceFlowLogTimeActiveread-onlycurrentThe total time that service flow was active.
1.3.6.1.2.1.10.127.7.1.7.1.11ColumndocsQosServiceFlowLogDirectionread-onlycurrentThe value of docsQosServiceFlowDirection for the service flow.
1.3.6.1.2.1.10.127.7.1.7.1.12ColumndocsQosServiceFlowLogPrimaryread-onlycurrentThe value of docsQosServiceFlowPrimary for the service flow.
1.3.6.1.2.1.10.127.7.1.7.1.13ColumndocsQosServiceFlowLogServiceClassNameread-onlycurrentThe value of docsQosParamSetServiceClassName for the provisioned QOS Parameter Set of the service flow.
1.3.6.1.2.1.10.127.7.1.7.1.14ColumndocsQosServiceFlowLogPolicedDropPktsread-onlycurrentThe final value of docsQosServiceFlowPolicedDropPkts for the service flow.
1.3.6.1.2.1.10.127.7.1.7.1.15ColumndocsQosServiceFlowLogPolicedDelayPktsread-onlycurrentThe final value of docsQosServiceFlowPolicedDelayPkts for the service flow.
1.3.6.1.2.1.10.127.7.1.7.1.16ColumndocsQosServiceFlowLogControlread-writecurrentSetting this object to the value destroy(6) removes this entry from the table. Reading this object return the value active(1).
1.3.6.1.2.1.10.127.7.1.8TabledocsQosServiceClassTablenot-accessiblecurrentThis table describes the set of Docsis-QOS Service Classes in a CMTS.
1.3.6.1.2.1.10.127.7.1.8.1RowdocsQosServiceClassEntrynot-accessiblecurrentA provisioned service class on a CMTS. Each entry defines a template for certain DOCSIS QOS Parameter Set values. When a CM creates or modifies an Admitted QOS…
1.3.6.1.2.1.10.127.7.1.8.1.1ColumndocsQosServiceClassNamenot-accessiblecurrentService Class Name. DOCSIS specifies that the maximum size is 15 printable ASCII characters with a terminating zero. The terminating zero is not represented in…
1.3.6.1.2.1.10.127.7.1.8.1.3ColumndocsQosServiceClassStatusread-createcurrentUsed to create or delete rows in this table.
1.3.6.1.2.1.10.127.7.1.8.1.4ColumndocsQosServiceClassPriorityread-createcurrentTemplate for docsQosParamSetPriority.
1.3.6.1.2.1.10.127.7.1.8.1.5ColumndocsQosServiceClassMaxTrafficRateread-createcurrentTemplate for docsQosParamSetMaxTrafficRate.
1.3.6.1.2.1.10.127.7.1.8.1.6ColumndocsQosServiceClassMaxTrafficBurstread-createcurrentTemplate for docsQosParamSetMaxTrafficBurst.
1.3.6.1.2.1.10.127.7.1.8.1.7ColumndocsQosServiceClassMinReservedRateread-createcurrentTemplate for docsQosParamSEtMinReservedRate.
1.3.6.1.2.1.10.127.7.1.8.1.8ColumndocsQosServiceClassMinReservedPktread-createcurrentTemplate for docsQosParamSetMinReservedPkt.
1.3.6.1.2.1.10.127.7.1.8.1.9ColumndocsQosServiceClassMaxConcatBurstread-createcurrentTemplate for docsQosParamSetMaxConcatBurst.
1.3.6.1.2.1.10.127.7.1.8.1.10ColumndocsQosServiceClassNomPollIntervalread-createcurrentTemplate for docsQosParamSetNomPollInterval.
1.3.6.1.2.1.10.127.7.1.8.1.11ColumndocsQosServiceClassTolPollJitterread-createcurrentTemplate for docsQosParamSetTolPollJitter.
1.3.6.1.2.1.10.127.7.1.8.1.12ColumndocsQosServiceClassUnsolicitGrantSizeread-createcurrentTemplate for docsQosParamSetUnsolicitGrantSize.
1.3.6.1.2.1.10.127.7.1.8.1.13ColumndocsQosServiceClassNomGrantIntervalread-createcurrentTemplate for docsQosParamSetNomGrantInterval.
1.3.6.1.2.1.10.127.7.1.8.1.14ColumndocsQosServiceClassTolGrantJitterread-createcurrentTemplate for docsQosParamSetTolGrantJitter.
1.3.6.1.2.1.10.127.7.1.8.1.15ColumndocsQosServiceClassGrantsPerIntervalread-createcurrentTemplate for docsQosParamSetGrantsPerInterval.
1.3.6.1.2.1.10.127.7.1.8.1.16ColumndocsQosServiceClassMaxLatencyread-createcurrentTemplate for docsQosParamSetClassMaxLatency.
1.3.6.1.2.1.10.127.7.1.8.1.17ColumndocsQosServiceClassActiveTimeoutread-createcurrentTemplate for docsQosServiceFlowActiveTimeout.
1.3.6.1.2.1.10.127.7.1.8.1.18ColumndocsQosServiceClassAdmittedTimeoutread-createcurrentTemplate for docsQosServiceFlowAdmittedTimeout.
1.3.6.1.2.1.10.127.7.1.8.1.19ColumndocsQosServiceClassSchedulingTyperead-createcurrentTemplate for docsQosServiceFlowSchedulingType.
1.3.6.1.2.1.10.127.7.1.8.1.20ColumndocsQosServiceClassRequestPolicyread-createcurrentTemplate for docsQosServiceFlowRequestPolicy.
1.3.6.1.2.1.10.127.7.1.8.1.21ColumndocsQosServiceClassTosAndMaskread-createcurrentTemplate for docsQosServiceFlowTosAndMask.
1.3.6.1.2.1.10.127.7.1.8.1.22ColumndocsQosServiceClassTosOrMaskread-createcurrentTemplate for docsQosServiceFlowTosOrMask.
1.3.6.1.2.1.10.127.7.1.8.1.23ColumndocsQosServiceClassDirectionread-createcurrentSpecifies whether the service class template applies to upstream or downstream service flows.
1.3.6.1.2.1.10.127.7.1.9TabledocsQosServiceClassPolicyTablenot-accessiblecurrentThis table describes the set of Docsis-QOS Service Class Policies. This table is an adjunct to the docsDevFilterPolicy table. Entries in docsDevFilterPolicy ta…
1.3.6.1.2.1.10.127.7.1.9.1RowdocsQosServiceClassPolicyEntrynot-accessiblecurrentA service class name policy entry.
1.3.6.1.2.1.10.127.7.1.9.1.1ColumndocsQosServiceClassPolicyIndexnot-accessiblecurrentIndex value to uniquely identify an entry in this table.
1.3.6.1.2.1.10.127.7.1.9.1.2ColumndocsQosServiceClassPolicyNameread-createcurrentService Class Name to identify the name of the service class flow to which the packet should be directed.
1.3.6.1.2.1.10.127.7.1.9.1.3ColumndocsQosServiceClassPolicyRulePriorityread-createcurrentService Class Policy rule priority for the entry.
1.3.6.1.2.1.10.127.7.1.9.1.4ColumndocsQosServiceClassPolicyStatusread-createcurrentUsed to create or delete rows in this table. This object should not be deleted if it is reference by an entry in docsDevFilterPolicy. The reference should be d…
1.3.6.1.2.1.10.127.7.1.10TabledocsQosPHSTablenot-accessiblecurrentThis table describes set of payload header suppression entries.
1.3.6.1.2.1.10.127.7.1.10.1RowdocsQosPHSEntrynot-accessiblecurrentA payload header suppression entry. The ifIndex is an ifType of docsCableMaclayer(127). The index docsQosServiceFlowId selects one service flow from the cable …
1.3.6.1.2.1.10.127.7.1.10.1.2ColumndocsQosPHSFieldread-onlycurrentPayload header suppression field defines the bytes of the header which must be suppressed/restored by the sending/receiving device. The number of octets in thi…
1.3.6.1.2.1.10.127.7.1.10.1.3ColumndocsQosPHSMaskread-onlycurrentPayload header suppression mask defines the bit mask which used in combination with the docsQosPHSField defines which bytes in header must be suppressed/restor…
1.3.6.1.2.1.10.127.7.1.10.1.4ColumndocsQosPHSSizeread-onlycurrentPayload header suppression size specifies the number of bytes in the header to be suppressed and restored. The value of this object must match the number of by…
1.3.6.1.2.1.10.127.7.1.10.1.5ColumndocsQosPHSVerifyread-onlycurrentPayload header suppression verification value of 'true' the sender must verify docsQosPHSField is the same as what is contained in the packet to be suppressed.
1.3.6.1.2.1.10.127.7.1.10.1.7ColumndocsQosPHSIndexread-onlycurrentPayload header suppression index uniquely references the PHS rule for a given service flow.
1.3.6.1.2.1.10.127.7.1.11TabledocsQosCmtsMacToSrvFlowTablenot-accessiblecurrentThis table provide for referencing the service flows associated with a particular cable modem. This allows for indexing into other docsQos tables that are inde…
1.3.6.1.2.1.10.127.7.1.11.1RowdocsQosCmtsMacToSrvFlowEntrynot-accessiblecurrentAn entry is created by CMTS for each service flow connected to this CMTS.
1.3.6.1.2.1.10.127.7.1.11.1.1ColumndocsQosCmtsCmMacnot-accessiblecurrentThe MAC address for the referenced CM.
1.3.6.1.2.1.10.127.7.1.11.1.2ColumndocsQosCmtsServiceFlowIdnot-accessiblecurrentAn index assigned to a service flow by CMTS.
1.3.6.1.2.1.10.127.7.1.11.1.3ColumndocsQosCmtsIfIndexread-onlycurrentThe ifIndex of ifType docsCableMacLayter(127) on the CMTS that is connected to the Cable Modem.
1.3.6.1.2.1.10.127.7.2NodedocsQosNotification
1.3.6.1.2.1.10.127.7.3NodedocsQosConformance
1.3.6.1.2.1.10.127.7.3.1NodedocsQosGroups
1.3.6.1.2.1.10.127.7.3.1.1GroupdocsQosBaseGroupcurrentGroup of objects implemented in both Cable Modems and Cable Modem Termination Systems.
1.3.6.1.2.1.10.127.7.3.1.2GroupdocsQosParamSetGroupcurrentGroup of objects implemenent in both Cable Modems and Cable Modem Termination Systems for QOS parameter sets.
1.3.6.1.2.1.10.127.7.3.1.3GroupdocsQosCmtsGroupcurrentMandatory group of objects implemented only in the CMTS.
1.3.6.1.2.1.10.127.7.3.1.4GroupdocsQosSrvClassPolicyGroupcurrentGroup of objects implemented in both Cable Modems and Cable Modem Termination Systems when supporting policy based service flows.
1.3.6.1.2.1.10.127.7.3.1.5GroupdocsQosServiceClassGroupcurrentThe docsQosServiceClassTable objects. If a CMTS implements expansion of Service Class Names in a QOS Parameter Set, this group is mandatory on the CMTS. If the…
1.3.6.1.2.1.10.127.7.3.2NodedocsQosCompliances
1.3.6.1.2.1.10.127.7.3.2.1CompliancedocsQosCompliancecurrentThe compliance statement for MCNS Cable Modems and Cable Modem Termination Systems that implement DOCSIS Service Flows.
Type Definitions
NameSyntaxStatusDescription
BitRateUnsigned32currentThe rate of traffic in unit of bits per second. Used to specify traffic rate for QOS.
IfDirectionINTEGER { downstream(1), upstream(2) }currentIndicates a direction on an RF MAC interface. The value downstream(1) is from Cable Modem Termination System to Cable Modem. The value upstream(2) is from Cable Modem to Cable Modem Termination System.
SchedulingTypeINTEGER { undefined (1), bestEffort (2), nonRealTimePollingService(3), realTimePollingService(4), unsolictedGrantServiceWithAD(5), unsolictedGrantService(6) }currentThe scheduling service provided by a CMTS for an upstream service flow. If the parameter is omitted from an upstream QOS Parameter Set, this object takes the value of bestEffort (2). This parameter must be reported as u…
MIB Viewer