HM2-DIAGNOSTIC-MIB
242 objects
Hirschmann Diagnostic MIB. Copyright (C) 2012. All Rights Reserved.
Imported Objects
| HM2-DEVMGMT-MIB | hm2IfacePhysIndex |
| HM2-PWRMGMT-MIB | hm2PSID |
| HM2-TC-MIB | hm2ConfigurationMibs HmEnabledStatus HmTimeSeconds1970 |
| IF-MIB | ifIndex |
| SNMPv2-SMI | Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-IDENTITY OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | -- RFC 2578 TEXTUAL-CONVENTION TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.248.11.22 | Identityhm2DiagnosticMib | Hirschmann Diagnostic MIB. Copyright (C) 2012. All Rights Reserved. | ||
| 1.3.6.1.4.1.248.11.22.0 | Nodehm2DiagnosticMibNotifications | |||
| 1.3.6.1.4.1.248.11.22.0.1 | Notificationhm2SigConStateChangeTrap | current | This trap is sent if the value of hm2SigConState changes its value. | |
| 1.3.6.1.4.1.248.11.22.0.2 | Notificationhm2DevMonStateChangeTrap | current | This trap is sent if the value of hm2DevMonState changes its value. | |
| 1.3.6.1.4.1.248.11.22.0.3 | Notificationhm2DevSecStateChangeTrap | current | This trap is sent if the value of hm2DevSecState changes its value. | |
| 1.3.6.1.4.1.248.11.22.0.4 | Notificationhm2DiagSelftestActionTrap | current | This trap is sent if a self-test action is performed and hm2DiagSelftestAction is configured to sendTrap(2). | |
| 1.3.6.1.4.1.248.11.22.0.5 | Notificationhm2DiagIfaceUtilizationTrap | current | This trap is sent if the value of hm2DiagIfaceUtilization exceeds or falls back below the interface utilization thresholds hm2DiagIfaceUtilizationAlarmConditio… | |
| 1.3.6.1.4.1.248.11.22.0.6 | Notificationhm2PortMonitorPortTrap | current | This trap is sent if the a port has been disabled by port disable action by port monitor. | |
| 1.3.6.1.4.1.248.11.22.0.7 | Notificationhm2DiagEgressIfaceUtilizationTrap | current | This trap is sent if the value of hm2DiagEgressIfaceUtilizationAlarmCondition is true. | |
| 1.3.6.1.4.1.248.11.22.1 | Nodehm2DiagnosticMibObjects | |||
| 1.3.6.1.4.1.248.11.22.1.1 | Nodehm2DiagSelftestGroup | |||
| 1.3.6.1.4.1.248.11.22.1.1.1 | Scalarhm2DiagSelftestRAM | read-write | current | Controls RAM self-test on cold start of the device. When disabled the device booting time is reduced. |
| 1.3.6.1.4.1.248.11.22.1.1.2 | Scalarhm2DiagSelftestBootTime | read-only | current | Internal boot time in Milliseconds until activating ports. |
| 1.3.6.1.4.1.248.11.22.1.1.10 | Tablehm2DiagSelftestActionTable | not-accessible | current | Diag self test action group. |
| 1.3.6.1.4.1.248.11.22.1.1.10.1 | Rowhm2DiagSelftestActionEntry | not-accessible | current | Diag self test action entry. |
| 1.3.6.1.4.1.248.11.22.1.1.10.1.1 | Columnhm2DiagSelftestActionCause | read-only | current | The area of the cause for the action the self-test wants to take. |
| 1.3.6.1.4.1.248.11.22.1.1.10.1.2 | Columnhm2DiagSelftestAction | read-write | current | The action that the self-test component should take. The cause is always logged to the system log, additionally a trap can be sent to the management station or… |
| 1.3.6.1.4.1.248.11.22.1.2 | Nodehm2DiagBootGroup | |||
| 1.3.6.1.4.1.248.11.22.1.2.1 | Scalarhm2BootSystemMonitor | read-write | current | Enable or disable the System Monitor access during the boot phase. Please note: If the System Monitor is disabled, it is possible to lose access to the device … |
| 1.3.6.1.4.1.248.11.22.1.2.2 | Scalarhm2BootDefaultConfigOnError | read-write | current | Enable or disable loading of the default configuration in case there is any error loading the configuration during the boot phase. If disabled the system will … |
| 1.3.6.1.4.1.248.11.22.1.2.3 | Scalarhm2BootConfigPushButton | read-write | current | Enable or disable the push button functionality on the device. |
| 1.3.6.1.4.1.248.11.22.1.3 | Nodehm2DiagDeviceMonitorGroup | |||
| 1.3.6.1.4.1.248.11.22.1.3.1 | Nodehm2SignalContactGroup | |||
| 1.3.6.1.4.1.248.11.22.1.3.1.1 | Tablehm2SigConCommonTable | not-accessible | current | This table contains all variables to configure the behavior of the signalling contacts. |
| 1.3.6.1.4.1.248.11.22.1.3.1.1.1 | Rowhm2SigConCommonEntry | not-accessible | current | The entry of the hm2SigConConfigTable. |
| 1.3.6.1.4.1.248.11.22.1.3.1.1.1.1 | Columnhm2SigConID | read-only | current | This index is used to identify the associated signalling contact. |
| 1.3.6.1.4.1.248.11.22.1.3.1.1.1.2 | Columnhm2SigConTrapEnable | read-write | current | Determines whether a trap shall be sent or not, when the signal contact operating state changes. |
| 1.3.6.1.4.1.248.11.22.1.3.1.1.1.3 | Columnhm2SigConTrapCause | read-only | current | This object identifies the cause for a trap. The index of the entity which produces the trap is specified by hm2SigConTrapCauseIndex. |
| 1.3.6.1.4.1.248.11.22.1.3.1.1.1.4 | Columnhm2SigConTrapCauseIndex | read-only | current | This attribute specifies the entity which produces the trap. power-supply: index of power-supply table link-failure: index of interface table temperature: 0 ex… |
| 1.3.6.1.4.1.248.11.22.1.3.1.1.1.5 | Columnhm2SigConMode | read-write | current | This attribute specifies the behavior of the relay contact. The factory settings for signal contact 1 is monitoring the correct operation of entries specified … |
| 1.3.6.1.4.1.248.11.22.1.3.1.1.1.6 | Columnhm2SigConOperState | read-only | current | This attribute shows the current operating state of the signal contact. |
| 1.3.6.1.4.1.248.11.22.1.3.1.1.1.7 | Columnhm2SigConOperTimeStamp | read-only | current | This attribute shows local system time (hm2SystemLocalTime) of the last hm2SigConOperState change. |
| 1.3.6.1.4.1.248.11.22.1.3.1.1.1.8 | Columnhm2SigConManualActivate | read-write | current | When operating in manual mode, the signal contact state can be set by this attribute. |
| 1.3.6.1.4.1.248.11.22.1.3.1.1.1.9 | Columnhm2SigConSenseLinkFailure | read-write | current | Sets the monitoring of the network connection(s). |
| 1.3.6.1.4.1.248.11.22.1.3.1.1.1.10 | Columnhm2SigConSenseTemperature | read-write | current | Sets the monitoring of the device temperature. |
| 1.3.6.1.4.1.248.11.22.1.3.1.1.1.11 | Columnhm2SigConSenseFan | read-write | current | Sets the monitoring of the device fan modules. |
| 1.3.6.1.4.1.248.11.22.1.3.1.1.1.12 | Columnhm2SigConSenseModuleRemoval | read-write | current | Sets the monitoring of module removal (platform dependant). |
| 1.3.6.1.4.1.248.11.22.1.3.1.1.1.13 | Columnhm2SigConSenseExtNvmRemoval | read-write | current | Sets the monitoring of the external non-volatile memory removal. |
| 1.3.6.1.4.1.248.11.22.1.3.1.1.1.14 | Columnhm2SigConSenseExtNvmNotInSync | read-write | current | Sets the monitoring whether the external non-volatile memory is in sync with the configuration in NVRAM. |
| 1.3.6.1.4.1.248.11.22.1.3.1.1.1.15 | Columnhm2SigConSenseRingRedundancy | read-write | current | Sets the monitoring of the ring redundancy. |
| 1.3.6.1.4.1.248.11.22.1.3.1.1.1.16 | Columnhm2SigConSenseEthernetLoops | read-write | current | Sets the monitoring for Ethernet loops. |
| 1.3.6.1.4.1.248.11.22.1.3.1.1.1.17 | Columnhm2SigConSenseHumidity | read-write | current | Sets the monitoring of the device humidity. |
| 1.3.6.1.4.1.248.11.22.1.3.1.1.1.18 | Columnhm2SigConSenseStpPortBlock | read-write | current | Sets the monitoring for STP loops. |
| 1.3.6.1.4.1.248.11.22.1.3.1.2 | Tablehm2SigConPSTable | not-accessible | current | This table contains the configuration of all power supply states. |
| 1.3.6.1.4.1.248.11.22.1.3.1.2.1 | Rowhm2SigConPSEntry | not-accessible | current | The entry of the hm2SigConPSTable. |
| 1.3.6.1.4.1.248.11.22.1.3.1.2.1.1 | Columnhm2SigConSensePSState | read-write | current | Sets the monitoring of the power supply state. |
| 1.3.6.1.4.1.248.11.22.1.3.1.3 | Tablehm2SigConInterfaceTable | not-accessible | current | This table contains all variables to mask an alarm for the signalling relay, produced by a link. The index for a link corresponds with ifIndex. The table is al… |
| 1.3.6.1.4.1.248.11.22.1.3.1.3.1 | Rowhm2SigConInterfaceEntry | not-accessible | current | The entry of the hm2SigConLinkTable. |
| 1.3.6.1.4.1.248.11.22.1.3.1.3.1.1 | Columnhm2SigConSenseIfLinkAlarm | read-write | current | Indicates whether an alarm for the signalling relay of the associated link will be produced or not, so you can mask the value of ifMauMediaAvailable. |
| 1.3.6.1.4.1.248.11.22.1.3.1.4 | Tablehm2SigConModuleTable | not-accessible | current | This table contains all variables to mask a module for the signaling relay. The index for a module corresponds with the slot number. |
| 1.3.6.1.4.1.248.11.22.1.3.1.4.1 | Rowhm2SigConModuleEntry | not-accessible | current | The entry of the hm2SigConModuleTable. |
| 1.3.6.1.4.1.248.11.22.1.3.1.4.1.1 | Columnhm2SigConModID | read-only | current | This index is used to identify the associated module. |
| 1.3.6.1.4.1.248.11.22.1.3.1.4.1.2 | Columnhm2SigConSenseModule | read-write | current | Indicates whether an alarm for the signalling relay of the associated module will be produced or not. |
| 1.3.6.1.4.1.248.11.22.1.3.1.5 | Tablehm2SigConFanModuleTable | not-accessible | current | This table contains all variables to mask a fan module for the signaling relay. The index for a module corresponds with the module number. |
| 1.3.6.1.4.1.248.11.22.1.3.1.5.1 | Rowhm2SigConFanModuleEntry | not-accessible | current | The entry of the hm2SigConFanModuleTable. |
| 1.3.6.1.4.1.248.11.22.1.3.1.5.1.1 | Columnhm2SigConFanModID | read-only | current | This index is used to identify the associated fan module. |
| 1.3.6.1.4.1.248.11.22.1.3.1.5.1.2 | Columnhm2SigConSenseFanModule | read-write | current | Indicates whether an alarm for the signalling relay of the associated fan module will be produced or not. |
| 1.3.6.1.4.1.248.11.22.1.3.1.10 | Tablehm2SigConStatusTable | not-accessible | current | This table shows the current monitored entities for which there is a trap cause (hm2SigConTrapCause) active. |
| 1.3.6.1.4.1.248.11.22.1.3.1.10.1 | Rowhm2SigConStatusEntry | not-accessible | current | The entry of the hm2SigConStatusTable. |
| 1.3.6.1.4.1.248.11.22.1.3.1.10.1.1 | Columnhm2SigConStatusIndex | not-accessible | current | This index is used to identify the occured event. |
| 1.3.6.1.4.1.248.11.22.1.3.1.10.1.2 | Columnhm2SigConStatusTimeStamp | read-only | current | This attribute shows the local system time (hm2SystemLocalTime) of occuration the event. |
| 1.3.6.1.4.1.248.11.22.1.3.1.10.1.3 | Columnhm2SigConStatusTrapCause | read-only | current | This object identifies the cause for a trap. The index of the entity which produces the trap is specified by hm2SigConTrapCauseIndex. |
| 1.3.6.1.4.1.248.11.22.1.3.1.10.1.4 | Columnhm2SigConStatusTrapCauseIndex | read-only | current | This attribute specifies the entity which produces the trap. power-supply: index of power-supply table link-failure: index of interface table temperature: 0 ex… |
| 1.3.6.1.4.1.248.11.22.1.3.2 | Nodehm2DeviceMonitorGroup | |||
| 1.3.6.1.4.1.248.11.22.1.3.2.1 | Tablehm2DevMonCommonTable | not-accessible | current | This table contains all variables to configure the behavior of the signalling contacts. |
| 1.3.6.1.4.1.248.11.22.1.3.2.1.1 | Rowhm2DevMonCommonEntry | not-accessible | current | The entry of the hm2DevMonConfigTable. |
| 1.3.6.1.4.1.248.11.22.1.3.2.1.1.1 | Columnhm2DevMonID | read-only | current | This index is used to identify the associated device monitoring group. Currently only one group is supported |
| 1.3.6.1.4.1.248.11.22.1.3.2.1.1.2 | Columnhm2DevMonTrapEnable | read-write | current | Determines whether a trap shall be sent or not when the signal contact operating state changes. |
| 1.3.6.1.4.1.248.11.22.1.3.2.1.1.3 | Columnhm2DevMonTrapCause | read-only | current | This object identifies the cause for a trap. The index of the entity which produces the trap is specified by hm2DevMonTrapCauseIndex. |
| 1.3.6.1.4.1.248.11.22.1.3.2.1.1.4 | Columnhm2DevMonTrapCauseIndex | read-only | current | This attribute specifies the entity which produces the trap. power-supply: index of power supply table link-failure: index of interface table temperature: 0 ex… |
| 1.3.6.1.4.1.248.11.22.1.3.2.1.1.5 | Columnhm2DevMonOperState | read-only | current | This attribute shows the current operating state of the signal contact. |
| 1.3.6.1.4.1.248.11.22.1.3.2.1.1.6 | Columnhm2DevMonOperTimeStamp | read-only | current | This attribute shows the local system time (hm2SystemLocalTime) of the last hm2DevMonOperState change. |
| 1.3.6.1.4.1.248.11.22.1.3.2.1.1.7 | Columnhm2DevMonSenseLinkFailure | read-write | current | Sets the monitoring of the network connection(s). |
| 1.3.6.1.4.1.248.11.22.1.3.2.1.1.8 | Columnhm2DevMonSenseTemperature | read-write | current | Sets the monitoring of the device temperature. |
| 1.3.6.1.4.1.248.11.22.1.3.2.1.1.9 | Columnhm2DevMonSenseFan | read-write | current | Sets the monitoring of the device fan modules. |
| 1.3.6.1.4.1.248.11.22.1.3.2.1.1.10 | Columnhm2DevMonSenseModuleRemoval | read-write | current | Sets the monitoring of module removal (platform dependent). |
| 1.3.6.1.4.1.248.11.22.1.3.2.1.1.11 | Columnhm2DevMonSenseExtNvmRemoval | read-write | current | Sets the monitoring of the external non-volatile memory removal. |
| 1.3.6.1.4.1.248.11.22.1.3.2.1.1.12 | Columnhm2DevMonSenseExtNvmNotInSync | read-write | current | Sets the monitoring whether the external non-volatile memory is in sync with the configuration in NVRAM. |
| 1.3.6.1.4.1.248.11.22.1.3.2.1.1.13 | Columnhm2DevMonSenseRingRedundancy | read-write | current | Sets the monitoring of the ring redundancy. |
| 1.3.6.1.4.1.248.11.22.1.3.2.1.1.14 | Columnhm2DevMonSenseHumidity | read-write | current | Sets the monitoring of the device humidity. |
| 1.3.6.1.4.1.248.11.22.1.3.2.1.1.15 | Columnhm2DevMonSenseStpPortBlock | read-write | current | Sets the monitoring whether a port was blocked by STP. |
| 1.3.6.1.4.1.248.11.22.1.3.2.2 | Tablehm2DevMonPSTable | not-accessible | current | This table contains the configuration of all power supply states. |
| 1.3.6.1.4.1.248.11.22.1.3.2.2.1 | Rowhm2DevMonPSEntry | not-accessible | current | The entry of the hm2DevMonPSTable. |
| 1.3.6.1.4.1.248.11.22.1.3.2.2.1.1 | Columnhm2DevMonSensePSState | read-write | current | Sets the monitoring of the power supply state. |
| 1.3.6.1.4.1.248.11.22.1.3.2.3 | Tablehm2DevMonInterfaceTable | not-accessible | current | This table contains all variables to mask an alarm for the signalling relay, produced by a link. The index for a link corresponds with ifIndex. The table is al… |
| 1.3.6.1.4.1.248.11.22.1.3.2.3.1 | Rowhm2DevMonInterfaceEntry | not-accessible | current | The entry of the hm2DevMonLinkTable. |
| 1.3.6.1.4.1.248.11.22.1.3.2.3.1.1 | Columnhm2DevMonSenseIfLinkAlarm | read-write | current | Indicates whether an alarm for the signalling relay of the associated link will be produced or not, so you can mask the value of ifMauMediaAvailable. |
| 1.3.6.1.4.1.248.11.22.1.3.2.4 | Tablehm2DevMonModuleTable | not-accessible | current | This table contains all variables to mask a module for the device status. The index for a module corresponds with the slot number. |
| 1.3.6.1.4.1.248.11.22.1.3.2.4.1 | Rowhm2DevMonModuleEntry | not-accessible | current | The entry of the hm2DevMonModuleTable. |
| 1.3.6.1.4.1.248.11.22.1.3.2.4.1.1 | Columnhm2DevMonModID | read-only | current | This index is used to identify the associated module. |
| 1.3.6.1.4.1.248.11.22.1.3.2.4.1.2 | Columnhm2DevMonSenseModule | read-write | current | Indicates whether an alarm for the device status of the associated module will be produced or not. |
| 1.3.6.1.4.1.248.11.22.1.3.2.5 | Tablehm2DevMonFanModuleTable | not-accessible | current | This table contains all variables to mask a fan module for the device status. The index for a module corresponds with the module number. |
| 1.3.6.1.4.1.248.11.22.1.3.2.5.1 | Rowhm2DevMonFanModuleEntry | not-accessible | current | The entry of the hm2DevMonFanModuleTable. |
| 1.3.6.1.4.1.248.11.22.1.3.2.5.1.1 | Columnhm2DevMonFanModID | read-only | current | This index is used to identify the associated fan module. |
| 1.3.6.1.4.1.248.11.22.1.3.2.5.1.2 | Columnhm2DevMonSenseFanModule | read-write | current | Indicates whether an alarm for the device status of the associated fan module will be produced or not. |
| 1.3.6.1.4.1.248.11.22.1.3.2.10 | Tablehm2DevMonStatusTable | not-accessible | current | This table shows the current monitored entities in the hm2DeviceMonitorGroup for which there is a trap cause (hm2DevMonStatusTrapCause) active. |
| 1.3.6.1.4.1.248.11.22.1.3.2.10.1 | Rowhm2DevMonStatusEntry | not-accessible | current | The entry of the hm2DevMonStatusTable. |
| 1.3.6.1.4.1.248.11.22.1.3.2.10.1.1 | Columnhm2DevMonStatusIndex | not-accessible | current | This index is used to identify the occured event. |
| 1.3.6.1.4.1.248.11.22.1.3.2.10.1.2 | Columnhm2DevMonStatusTimeStamp | read-only | current | This attribute shows the local system time (hm2SystemLocalTime) of occuration the event. |
| 1.3.6.1.4.1.248.11.22.1.3.2.10.1.3 | Columnhm2DevMonStatusTrapCause | read-only | current | This object identifies the cause for a trap. The index of the entity which produces the trap is specified by hm2DevMonTrapCauseIndex. |
| 1.3.6.1.4.1.248.11.22.1.3.2.10.1.4 | Columnhm2DevMonStatusTrapCauseIndex | read-only | current | This attribute specifies the entity which produces the trap. power-supply: index of power supply table link-failure: index of interface table temperature: 0 ex… |
| 1.3.6.1.4.1.248.11.22.1.3.3 | Nodehm2DeviceSecurityGroup | |||
| 1.3.6.1.4.1.248.11.22.1.3.3.1 | Nodehm2DevSecConfigGroup | |||
| 1.3.6.1.4.1.248.11.22.1.3.3.1.1 | Scalarhm2DevSecTrapEnable | read-write | current | Determines whether a trap shall be sent or not, when the device security operating state changes. |
| 1.3.6.1.4.1.248.11.22.1.3.3.1.2 | Scalarhm2DevSecTrapCause | read-only | current | This object identifies the cause for a trap. The index of the entity which produces the trap is specified by hm2DevMonTrapCauseIndex. |
| 1.3.6.1.4.1.248.11.22.1.3.3.1.3 | Scalarhm2DevSecTrapCauseIndex | read-only | current | This attribute specifies the entity which produces the trap. ext-nvm-update-enabled: (1) sd, (2) usb, (3) serial (not supported yet) no-link: index of interfac… |
| 1.3.6.1.4.1.248.11.22.1.3.3.1.4 | Scalarhm2DevSecOperState | read-only | current | This attribute shows the current operating state of the signal contact. |
| 1.3.6.1.4.1.248.11.22.1.3.3.1.5 | Scalarhm2DevSecOperTimeStamp | read-only | current | This attribute shows the local system time (hm2SystemLocalTime) of the last hm2DevSecOperState change. |
| 1.3.6.1.4.1.248.11.22.1.3.3.1.6 | Scalarhm2DevSecSensePasswordChange | read-write | current | Enable or disable to check if default passwords for 'user' and 'admin' are not changed. |
| 1.3.6.1.4.1.248.11.22.1.3.3.1.7 | Scalarhm2DevSecSensePasswordMinLength | read-write | current | Enable or disable to check if configured minimum password length is < 8 characters. |
| 1.3.6.1.4.1.248.11.22.1.3.3.1.8 | Scalarhm2DevSecSensePasswordStrengthNotConfigured | read-write | current | Enable or disable minimum password strength to check if (1 uppercase, 1 lowercase, 1 number, 1 non-alphanumeric) is not configured. |
| 1.3.6.1.4.1.248.11.22.1.3.3.1.9 | Scalarhm2DevSecSenseBypassPasswordStrength | read-write | current | Enable or disable to check if at least one user is configured to bypass strength check. |
| 1.3.6.1.4.1.248.11.22.1.3.3.1.10 | Scalarhm2DevSecSenseTelnetEnabled | read-write | current | Enable or disable to check if telnet is enabled on the switch. |
| 1.3.6.1.4.1.248.11.22.1.3.3.1.11 | Scalarhm2DevSecSenseHttpEnabled | read-write | current | Enable or disable to check if HTTP is enabled on the switch. |
| 1.3.6.1.4.1.248.11.22.1.3.3.1.12 | Scalarhm2DevSecSenseSnmpUnsecure | read-write | current | Enable or disable to check if SNMP v1/v2 is enabled or v3 encryption is disabled. |
| 1.3.6.1.4.1.248.11.22.1.3.3.1.13 | Scalarhm2DevSecSenseSysmonEnabled | read-write | current | Enable or disable to check if sysmon1 access is not disabled. |
| 1.3.6.1.4.1.248.11.22.1.3.3.1.14 | Scalarhm2DevSecSenseExtNvmUpdateEnabled | read-write | current | Enable or disable to check if external non-volatile memory update is not disabled. |
| 1.3.6.1.4.1.248.11.22.1.3.3.1.15 | Scalarhm2DevSecSenseNoLinkEnabled | read-write | current | Enable or disable to check if at least one port has no link but admin state is up. |
| 1.3.6.1.4.1.248.11.22.1.3.3.1.16 | Scalarhm2DevSecSenseHiDiscoveryEnabled | read-write | current | Enable or disable to check if HiDiscovery is enabled and the mode is 'read-write'. |
| 1.3.6.1.4.1.248.11.22.1.3.3.1.17 | Scalarhm2DevSecSenseExtNvmConfigLoadUnsecure | read-write | current | Enable or disable to check if the configuration load from external NVM is unsecure. (The configuration priority of the external NVM is set to 'first', 'second'… |
| 1.3.6.1.4.1.248.11.22.1.3.3.1.18 | Scalarhm2DevSecSenseIec61850MmsEnabled | read-write | current | Enable or disable to check if IEC 61850 MMS is enabled on the switch. |
| 1.3.6.1.4.1.248.11.22.1.3.3.1.19 | Scalarhm2DevSecSenseHttpsCertificateWarning | read-write | current | Enable or disable to check for the presence of the auto generated self-signed HTTPS certificate. |
| 1.3.6.1.4.1.248.11.22.1.3.3.1.20 | Scalarhm2DevSecSenseModbusTcpEnabled | read-write | current | Enable or disable to check if Modbus/TCP server is enabled on the switch. |
| 1.3.6.1.4.1.248.11.22.1.3.3.1.21 | Scalarhm2DevSecSenseEtherNetIpEnabled | read-write | current | Enable or disable to check if EtherNet/IP protocol is enabled on the switch. |
| 1.3.6.1.4.1.248.11.22.1.3.3.1.22 | Scalarhm2DevSecSenseProfinetIOEnabled | read-write | current | Enable or disable to check if ProfinetIO protocol is enabled on the switch. |
| 1.3.6.1.4.1.248.11.22.1.3.3.1.23 | Scalarhm2DevSecSensePMLDisabled | read-write | current | Enable or disable to check if Port MAC Locking is disabled on the switch. |
| 1.3.6.1.4.1.248.11.22.1.3.3.2 | Tablehm2DevSecInterfaceTable | not-accessible | current | This table contains all variables to mask an alarm for the signalling relay, produced by a link. The index for a link corresponds with ifIndex. The table is al… |
| 1.3.6.1.4.1.248.11.22.1.3.3.2.1 | Rowhm2DevSecInterfaceEntry | not-accessible | current | The entry of the hm2DevSecLinkTable. |
| 1.3.6.1.4.1.248.11.22.1.3.3.2.1.1 | Columnhm2DevSecSenseIfNoLink | read-write | current | Port has no link but admin state is up |
| 1.3.6.1.4.1.248.11.22.1.3.3.10 | Tablehm2DevSecStatusTable | not-accessible | current | This table shows the current monitored entities in the hm2DevSecConfigGroup for which there is a trap cause (hm2DevSecStatusTrapCause) active. |
| 1.3.6.1.4.1.248.11.22.1.3.3.10.1 | Rowhm2DevSecStatusEntry | not-accessible | current | The entry of the hm2DevSecStatusTable. |
| 1.3.6.1.4.1.248.11.22.1.3.3.10.1.1 | Columnhm2DevSecStatusIndex | not-accessible | current | This index is used to identify the occured event. |
| 1.3.6.1.4.1.248.11.22.1.3.3.10.1.2 | Columnhm2DevSecStatusTimeStamp | read-only | current | This attribute shows the local system time (hm2SystemLocalTime) of occuration the event. |
| 1.3.6.1.4.1.248.11.22.1.3.3.10.1.3 | Columnhm2DevSecStatusTrapCause | read-only | current | This object identifies the cause for a trap. The index of the entity which produces the trap is specified by hm2DevSecTrapCauseIndex. |
| 1.3.6.1.4.1.248.11.22.1.3.3.10.1.4 | Columnhm2DevSecStatusTrapCauseIndex | read-only | current | This attribute specifies the entity which produces the trap. ext-nvm-update-enabled: (1) sd, (2) usb, (3) serial (not supported yet) no-link: index of interfac… |
| 1.3.6.1.4.1.248.11.22.1.4 | Nodehm2DiagLedGroup | |||
| 1.3.6.1.4.1.248.11.22.1.4.1 | Tablehm2LedGlobalTable | not-accessible | current | . |
| 1.3.6.1.4.1.248.11.22.1.4.1.1 | Rowhm2LedGlobalEntry | not-accessible | current | . |
| 1.3.6.1.4.1.248.11.22.1.4.1.1.1 | Columnhm2LedGlobalLedType | not-accessible | current | . |
| 1.3.6.1.4.1.248.11.22.1.4.1.1.2 | Columnhm2LedGlobalStatus | read-only | current | . |
| 1.3.6.1.4.1.248.11.22.1.4.2 | Tablehm2LedPortTable | not-accessible | current | . |
| 1.3.6.1.4.1.248.11.22.1.4.2.1 | Rowhm2LedPortEntry | not-accessible | current | . |
| 1.3.6.1.4.1.248.11.22.1.4.2.1.1 | Columnhm2LedPortStatus | read-only | current | . |
| 1.3.6.1.4.1.248.11.22.1.4.2.1.2 | Columnhm2LedPortPoeStatus | read-only | current | . |
| 1.3.6.1.4.1.248.11.22.1.4.2.1.3 | Columnhm2LedPortSignaling | read-write | current | Enable for LED port signaling. |
| 1.3.6.1.4.1.248.11.22.1.4.3 | Nodehm2LedControlGroup | |||
| 1.3.6.1.4.1.248.11.22.1.4.3.1 | Scalarhm2LedPortMode | read-write | current | Switch LED signalling between the port LEDs on front side (port panel) and the port LEDs on the back side (service panel) of the device. |
| 1.3.6.1.4.1.248.11.22.1.5 | Nodehm2DiagIfaceUtilizationGroup | |||
| 1.3.6.1.4.1.248.11.22.1.5.1 | Tablehm2DiagIfaceUtilizationTable | not-accessible | current | This table contains variables for each interface of the switch. |
| 1.3.6.1.4.1.248.11.22.1.5.1.1 | Rowhm2DiagIfaceUtilizationEntry | not-accessible | current | The entry of the hm2DiagIfaceUtilizationTable. |
| 1.3.6.1.4.1.248.11.22.1.5.1.1.1 | Columnhm2DiagIfaceUtilization | read-only | current | The best estimate of the mean physical layer network utilization on this interface during the last sampling interval, in hundredth of one percent. The first hi… |
| 1.3.6.1.4.1.248.11.22.1.5.1.1.2 | Columnhm2DiagIfaceUtilizationControlInterval | read-write | current | The interval in seconds over which the data is sampled for hm2DiagIfaceUtilization. This interval can be any number of seconds between 1 and 3600 (1 hour). The… |
| 1.3.6.1.4.1.248.11.22.1.5.1.1.3 | Columnhm2DiagIfaceUtilizationAlarmLowerThreshold | read-write | current | Surveys the interface utilization hm2DiagIfaceUtilization and generates an alarm for this interfaces, if the utilization value is below the given limit. A valu… |
| 1.3.6.1.4.1.248.11.22.1.5.1.1.4 | Columnhm2DiagIfaceUtilizationAlarmUpperThreshold | read-write | current | Surveys the interface utilization hm2DiagIfaceUtilization and generates an alarm for this interfaces, if the given limit is exceeded. A value of 0 disables the… |
| 1.3.6.1.4.1.248.11.22.1.5.1.1.5 | Columnhm2DiagIfaceUtilizationAlarmCondition | read-only | current | The alarm condition is given (true), if the given hm2DiagIfaceUtilizationAlarmUpperThreshold limit is exceeded by the interface utilization or if the utilizati… |
| 1.3.6.1.4.1.248.11.22.1.5.2 | Tablehm2DiagEgressIfaceUtilizationTable | not-accessible | current | This table contains egress variables for each interface of the switch. |
| 1.3.6.1.4.1.248.11.22.1.5.2.1 | Rowhm2DiagEgressIfaceUtilizationEntry | not-accessible | current | The entry of the hm2DiagEgressIfaceUtilizationTable. |
| 1.3.6.1.4.1.248.11.22.1.5.2.1.1 | Columnhm2DiagEgressIfaceUtilization | read-only | current | The best estimate of the mean physical layer network egress utilization on this interface during the last sampling interval, in hundredth of one percent. The f… |
| 1.3.6.1.4.1.248.11.22.1.5.2.1.2 | Columnhm2DiagEgressIfaceUtilizationControlInterval | read-write | current | The interval in seconds over which the egress data is sampled for hm2DiagEgressIfaceUtilization. This interval can be any number of seconds between 1 and 3600 … |
| 1.3.6.1.4.1.248.11.22.1.5.2.1.3 | Columnhm2DiagEgressIfaceUtilizationAlarmLowerThreshold | read-write | current | Surveys the egress interface utilization hm2DiagEgressIfaceUtilization and generates an alarm for this interface, if the utilization value is below the given l… |
| 1.3.6.1.4.1.248.11.22.1.5.2.1.4 | Columnhm2DiagEgressIfaceUtilizationAlarmUpperThreshold | read-write | current | Surveys the egress interface utilization hm2DiagEgressIfaceUtilization and generates an alarm for this interface, if the given limit is exceeded. A value of 0 … |
| 1.3.6.1.4.1.248.11.22.1.5.2.1.5 | Columnhm2DiagEgressIfaceUtilizationAlarmCondition | read-only | current | The alarm condition is given (true), if the given hm2DiagEgressIfaceUtilizationAlarmUpperThreshold limit is exceeded by the egress interface utilization or if … |
| 1.3.6.1.4.1.248.11.22.1.6 | Nodehm2DiagCableTesterGroup | |||
| 1.3.6.1.4.1.248.11.22.1.6.1 | Scalarhm2DiagCableTesterStatus | read-write | current | Status of the Virtual Cable Tester active(1) - Cable testing is in progress. Set to this value to start the test. success(2) - A successful test was performed.… |
| 1.3.6.1.4.1.248.11.22.1.6.2 | Scalarhm2DiagCableTesterIfIndex | read-write | current | Determines on which port to perform the cable test. Limited to copper based ports. |
| 1.3.6.1.4.1.248.11.22.1.6.10 | Tablehm2DiagCableTesterCableTable | not-accessible | current | This table contains variables for each pair of the cable. |
| 1.3.6.1.4.1.248.11.22.1.6.10.1 | Rowhm2DiagCableTesterCableEntry | not-accessible | current | The entry of the hm2DiagCableTesterCableTable. |
| 1.3.6.1.4.1.248.11.22.1.6.10.1.1 | Columnhm2DiagCableTesterCablePair | not-accessible | current | Index of the hm2DiagCableTesterCableTable. If a PHY does not support the measurement per pair, the first index is used to show the values. |
| 1.3.6.1.4.1.248.11.22.1.6.10.1.2 | Columnhm2DiagCableTesterCableStatus | read-only | current | Indicates the results of the Cable Test. normal(1) - The cable is working correctly. open(2) - The cable is disconnected or there is a faulty connector. short(… |
| 1.3.6.1.4.1.248.11.22.1.6.10.1.3 | Columnhm2DiagCableTesterCableMinimumLength | read-only | current | The estimated length of the cable in meters. This value indicates the shortest length estimated. This object will return 0 if hm2DiagCableTesterStatus is not s… |
| 1.3.6.1.4.1.248.11.22.1.6.10.1.4 | Columnhm2DiagCableTesterCableMaximumLength | read-only | current | The estimated length of the cable in meters. This value indicates the longest length estimated. This object will return 0 if hm2DiagCableTesterStatus is not su… |
| 1.3.6.1.4.1.248.11.22.1.6.10.1.5 | Columnhm2DiagCableTesterCableFailureLocation | read-only | current | The estimated distance in meters from the end of the cable to the failure location. This object will return 0 if hm2DiagCableTesterStatus is not success(2). |
| 1.3.6.1.4.1.248.11.22.1.7 | Nodehm2PortMonitorGroup | |||
| 1.3.6.1.4.1.248.11.22.1.7.1 | Scalarhm2PortMonitorAdminMode | read-write | current | Global switch to enable / disable the port state actions, which are performed if a condition becomes true |
| 1.3.6.1.4.1.248.11.22.1.7.2 | Tablehm2PortMonitorIntfTable | not-accessible | current | Port state mode interface table. |
| 1.3.6.1.4.1.248.11.22.1.7.2.1 | Rowhm2PortMonitorIntfEntry | not-accessible | current | Port state mode interface entry. |
| 1.3.6.1.4.1.248.11.22.1.7.2.1.2 | Columnhm2PortMonitorIntfReset | read-write | current | Port monitor interface reset. |
| 1.3.6.1.4.1.248.11.22.1.7.2.1.3 | Columnhm2PortMonitorIntfAction | read-write | current | Interface link disable state. |
| 1.3.6.1.4.1.248.11.22.1.7.3 | Nodehm2PortMonitorConditionGroup | |||
| 1.3.6.1.4.1.248.11.22.1.7.3.1 | Tablehm2PortMonitorConditionIntfTable | not-accessible | current | Port state condition interface table. |
| 1.3.6.1.4.1.248.11.22.1.7.3.1.1 | Rowhm2PortMonitorConditionIntfEntry | not-accessible | current | Port state action interface entry. |
| 1.3.6.1.4.1.248.11.22.1.7.3.1.1.1 | Columnhm2PortMonitorConditionField | read-only | current | Condition type field. |
| 1.3.6.1.4.1.248.11.22.1.7.3.1.1.2 | Columnhm2PortMonitorConditionLinkFlapMode | read-write | current | Interface link flap mode. |
| 1.3.6.1.4.1.248.11.22.1.7.3.1.1.3 | Columnhm2PortMonitorConditionCrcFragmentsMode | read-write | current | Interface CrcFragments mode. |
| 1.3.6.1.4.1.248.11.22.1.7.3.1.1.4 | Columnhm2PortMonitorConditionDuplexMismatchDetectionMode | read-write | current | Interface duplex mismatch detection mode. |
| 1.3.6.1.4.1.248.11.22.1.7.3.1.1.5 | Columnhm2PortMonitorConditionOverloadDetectionMode | read-write | current | Interface Overload Detection mode. |
| 1.3.6.1.4.1.248.11.22.1.7.3.1.1.6 | Columnhm2PortMonitorConditionSpeedDuplexMode | read-write | current | Interface Speed and Duplex monitor mode. |
| 1.3.6.1.4.1.248.11.22.1.7.3.2 | Nodehm2PortMonitorConditionLinkFlapGroup | |||
| 1.3.6.1.4.1.248.11.22.1.7.3.2.1 | Tablehm2PortMonitorConditionLinkFlapIntfTable | not-accessible | current | Port condition link flap interface table. |
| 1.3.6.1.4.1.248.11.22.1.7.3.2.1.1 | Rowhm2PortMonitorConditionLinkFlapIntfEntry | not-accessible | current | Port condition link flap interface entry. |
| 1.3.6.1.4.1.248.11.22.1.7.3.2.1.1.1 | Columnhm2PortMonitorConditionLinkFlapInterval | read-write | current | Measure interval in seconds (1-180s) for link flap detection. |
| 1.3.6.1.4.1.248.11.22.1.7.3.2.1.1.2 | Columnhm2PortMonitorConditionLinkFlapCount | read-write | current | Link flap counter (1-100). |
| 1.3.6.1.4.1.248.11.22.1.7.3.2.1.1.3 | Columnhm2PortMonitorConditionLinkFlapCountInterval | read-only | current | Link flap count that occured in last interval. |
| 1.3.6.1.4.1.248.11.22.1.7.3.2.1.1.4 | Columnhm2PortMonitorConditionLinkFlapCountTotal | read-only | current | Total link flap count. |
| 1.3.6.1.4.1.248.11.22.1.7.3.3 | Nodehm2PortMonitorConditionCrcFragmentsGroup | |||
| 1.3.6.1.4.1.248.11.22.1.7.3.3.1 | Tablehm2PortMonitorConditionCrcFragmentsIntfTable | not-accessible | current | Port condition CrcFragments interface table. |
| 1.3.6.1.4.1.248.11.22.1.7.3.3.1.1 | Rowhm2PortMonitorConditionCrcFragmentsIntfEntry | not-accessible | current | Port condition CrcFragments interface entry. |
| 1.3.6.1.4.1.248.11.22.1.7.3.3.1.1.1 | Columnhm2PortMonitorConditionCrcFragmentsInterval | read-write | current | Measure interval in seconds (5-180s) for CrcFragments detection. |
| 1.3.6.1.4.1.248.11.22.1.7.3.3.1.1.2 | Columnhm2PortMonitorConditionCrcFragmentsCount | read-write | current | CrcFragments counter (1-1000000). |
| 1.3.6.1.4.1.248.11.22.1.7.3.3.1.1.3 | Columnhm2PortMonitorConditionCrcFragmentsCountInterval | read-only | current | CrcFragments count that occured in last interval. |
| 1.3.6.1.4.1.248.11.22.1.7.3.3.1.1.4 | Columnhm2PortMonitorConditionCrcFragmentsCountTotal | read-only | current | Total CrcFragments count. |
| 1.3.6.1.4.1.248.11.22.1.7.3.4 | Nodehm2PortMonitorConditionOverloadDetectionGroup | |||
| 1.3.6.1.4.1.248.11.22.1.7.3.4.1 | Tablehm2PortMonitorConditionOvldDetIntfTable | not-accessible | current | Port condition overload detection interface table. |
| 1.3.6.1.4.1.248.11.22.1.7.3.4.1.1 | Rowhm2PortMonitorConditionOvldDetIntfEntry | not-accessible | current | Port condition overload detection interface entry. |
| 1.3.6.1.4.1.248.11.22.1.7.3.4.1.1.1 | Columnhm2PortMonitorConditionOvldDetTrfcType | read-write | current | Overload detection condition traffic type. |
| 1.3.6.1.4.1.248.11.22.1.7.3.4.1.1.2 | Columnhm2PortMonitorConditionOvldDetTholdType | read-write | current | Overload detection conditon threshold type. |
| 1.3.6.1.4.1.248.11.22.1.7.3.4.1.1.3 | Columnhm2PortMonitorConditionOvldDetLwrTholdVal | read-write | current | Overload detection condition lower threshold value. |
| 1.3.6.1.4.1.248.11.22.1.7.3.4.1.1.4 | Columnhm2PortMonitorConditionOvldDetUprTholdVal | read-write | current | Overload detection condition upper threshold value. |
| 1.3.6.1.4.1.248.11.22.1.7.3.4.1.1.5 | Columnhm2PortMonitorConditionOvldDetIntvl | read-write | current | Measure interval in seconds (1-20s) for overload detection. |
| 1.3.6.1.4.1.248.11.22.1.7.3.4.1.1.6 | Columnhm2PortMonitorConditionOvldDetPkgCntAll | read-only | current | All package count from last interval. |
| 1.3.6.1.4.1.248.11.22.1.7.3.4.1.1.7 | Columnhm2PortMonitorConditionOvldDetPkgCntBC | read-only | current | Broadcast package count from last interval. |
| 1.3.6.1.4.1.248.11.22.1.7.3.4.1.1.8 | Columnhm2PortMonitorConditionOvldDetPkgCntMC | read-only | current | Overload detection condition lower threshold value. |
| 1.3.6.1.4.1.248.11.22.1.7.3.4.1.1.9 | Columnhm2PortMonitorConditionOvldDetPkgCntKbit | read-only | current | Overload detection condition lower threshold value. |
| 1.3.6.1.4.1.248.11.22.1.7.3.5 | Nodehm2PortMonitorConditionSpeedDuplexGroup | |||
| 1.3.6.1.4.1.248.11.22.1.7.3.5.1 | Tablehm2PortMonitorConditionSpeedDuplexTable | not-accessible | current | Port condition speed-duplex interface table. |
| 1.3.6.1.4.1.248.11.22.1.7.3.5.1.1 | Rowhm2PortMonitorConditionSpeedDuplexEntry | not-accessible | current | Port condition speed-duplex interface entry. |
| 1.3.6.1.4.1.248.11.22.1.7.3.5.1.1.1 | Columnhm2PortMonitorConditionSpeedDuplexValue | read-write | current | Speed and duplex combination allowed by port-monitor. |
| 1.3.6.1.4.1.248.11.22.1.7.4 | Identityhm2KbpsUnitTrafficTypeInvalid | current | Interface {0}: 'Kbps' unit can only be used for traffic type 'all'. | |
| 1.3.6.1.4.1.248.11.22.1.8 | Nodehm2DiagResourcesGroup | |||
| 1.3.6.1.4.1.248.11.22.1.8.1 | Scalarhm2DiagEnableMeasurement | read-write | current | Enable or disable the resources measurement If disabled, the task - needed for measurement - is also deleted. |
| 1.3.6.1.4.1.248.11.22.1.8.10 | Nodehm2DiagCpuResourcesGroup | |||
| 1.3.6.1.4.1.248.11.22.1.8.10.1 | Scalarhm2DiagCpuUtilization | read-only | current | The current cpu utilization of the device in percent. |
| 1.3.6.1.4.1.248.11.22.1.8.10.2 | Scalarhm2DiagCpuAverageUtilization | read-only | current | The average cpu utilization of the device in percent, max. measured over the last 30 minutes. |
| 1.3.6.1.4.1.248.11.22.1.8.10.3 | Scalarhm2DiagCpuRunningProcesses | read-only | current | The current number of processes running. |
| 1.3.6.1.4.1.248.11.22.1.8.10.4 | Scalarhm2DiagCpuMaxRunningProcesses | read-only | current | The maximum number of processes running, max. since the last 30 minutes. |
| 1.3.6.1.4.1.248.11.22.1.8.11 | Nodehm2DiagMemoryResourcesGroup | |||
| 1.3.6.1.4.1.248.11.22.1.8.11.1 | Scalarhm2DiagMemoryRamAllocated | read-only | current | The current allocated RAM of the device in kBytes. |
| 1.3.6.1.4.1.248.11.22.1.8.11.2 | Scalarhm2DiagMemoryRamFree | read-only | current | The current free RAM of the device in kBytes. |
| 1.3.6.1.4.1.248.11.22.1.8.11.3 | Scalarhm2DiagMemoryRamAllocatedAverage | read-only | current | The average allocated RAM of the device in kBytes, measured over the last 30 minutes. |
| 1.3.6.1.4.1.248.11.22.1.8.11.4 | Scalarhm2DiagMemoryRamFreeAverage | read-only | current | The average free RAM of the device in kBytes, measured over the last 30 minutes. |
| 1.3.6.1.4.1.248.11.22.1.8.11.10 | Scalarhm2DiagMemoryRawFlashMainAllocated | read-only | current | The current allocated flash memory for the main software image in kBytes. |
| 1.3.6.1.4.1.248.11.22.1.8.11.11 | Scalarhm2DiagMemoryRawFlashMainFree | read-only | current | The current free flash memory for the main software image in kBytes. |
| 1.3.6.1.4.1.248.11.22.1.8.11.12 | Scalarhm2DiagMemoryFlashFileSystemAllocated | read-only | current | The current allocated memory within the flash file system in kBytes. |
| 1.3.6.1.4.1.248.11.22.1.8.11.13 | Scalarhm2DiagMemoryFlashFileSystemFree | read-only | current | The current free memory within the flash file system in kBytes. |
| 1.3.6.1.4.1.248.11.22.1.8.12 | Nodehm2DiagNetworkResourcesGroup | |||
| 1.3.6.1.4.1.248.11.22.1.8.12.1 | Scalarhm2DiagNetworkCpuIfUtilization | read-only | current | The current network utilization of the internal cpu interface in percent. |
| 1.3.6.1.4.1.248.11.22.1.8.12.2 | Scalarhm2DiagNetworkCpuIfAverageUtilization | read-only | current | The average network utilization of the internal cpu interface in percent, measured over the last 30 minutes. |
| 1.3.6.1.4.1.248.11.22.3 | Nodehm2DiagnosticSNMPExtensionGroup | |||
| 1.3.6.1.4.1.248.11.22.3.1 | Identityhm2PortMonitorSpeedDuplexErrorReturn | current | Indicates that the specified speed value is not supported by the port capabilities | |
| 1.3.6.1.4.1.248.11.22.3.2 | Identityhm2PortMonitorCndOvldDetInconsistenTholdVal | current | Indicates that the configured upper and lower threshold values are inconsistent |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| Hm2LedStatus | INTEGER { off(1), greenSolid(2), greenBlink1(3), greenBlink3(4), greenBlink4(5), greenBlink5(6), greenBlink5i(7), yellowSolid(8), yellowBlink1(9), yellowBlink3(10), yellowBlink4(11), yellowBlink5(12), redSolid(13), redBlink1(14), redBlink3(15), redBlink4(16), redBlink5(17) } | current | Status of LEDs available |
| Hm2LedType | INTEGER { power(1), status(2), rm(3), envm(4), i1(5), i2(6) } | current | Types of LEDs available |