HP-SN-MPLS-TE-MIB
138 objects
This MIB module contains managed object definitions for MPLS Traffic Engineering (TE) as defined in: 1. Extensions to RSVP for LSP Tunnels, Awduche et al, RFC 3209, December 2001 2. Constraint-Based LSP Setup using LDP, Jamoussi (Editor), Internet Draft <draft-ietf-mpls-cr-ldp- 06.txt>, November 2001 3. Requirements for Traffic Engineering Over MPLS, Awduche, D., Malcolm, J., Agogbua, J., O'Dell, M., and J. McManus, RFC 2702, September 1999
Imported Objects
| HP-SN-MPLS-TC-MIB | MplsBitRate MplsBurstSize MplsLSPID MplsLsrIdentifier mplsMIB MplsPathIndex MplsPathIndexOrZero MplsTunnelAffinity MplsTunnelIndex MplsTunnelInstanceIndex |
| HP-SN-ROOT-MIB | snMpls |
| IF-MIB | InterfaceIndexOrZero |
| INET-ADDRESS-MIB | InetAddressIPv4 InetAddressIPv6 |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Counter64 Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE TimeTicks Unsigned32 |
| SNMPv2-TC | DisplayString RowPointer RowStatus StorageType TimeStamp TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3 | IdentitymplsTeMIB | This MIB module contains managed object definitions for MPLS Traffic Engineering (TE) as defined in: 1. Extensions to RSVP for LSP Tunnels, Awduche et al, RFC … | ||
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.1 | NodemplsTeScalars | |||
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.1.1 | ScalarmplsTunnelConfigured | read-only | current | The number of tunnels configured on this device. A tunnel is considered configured if the mplsTunnelRowStatus is active(1). |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.1.2 | ScalarmplsTunnelActive | read-only | current | The number of tunnels active on this device. A tunnel is considered active if the mplsTunnelOperStatus is up(1). |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.1.3 | ScalarmplsTunnelTEDistProto | read-only | current | The traffic engineering distribution protocol(s) used by this LSR. Note that an LSR may support more than one distribution protocol simultaneously. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.1.4 | ScalarmplsTunnelMaxHops | read-only | current | The maximum number of hops that can be specified for a tunnel on this device. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2 | NodemplsTeObjects | |||
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.1 | ScalarmplsTunnelIndexNext | read-only | current | This object contains the next appropriate value to be used for mplsTunnelIndex when creating entries in mplsTunnelTable. If the number of unassigned entries is… |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2 | TablemplsTunnelTable | not-accessible | current | The mplsTunnelTable allows new MPLS tunnels to be created between an LSR and a remote endpoint, and existing tunnels to be reconfigured or removed. Note that o… |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1 | RowmplsTunnelEntry | not-accessible | current | An entry in this table represents an MPLS tunnel. An entry can be created by a network administrator or by an SNMP agent as instructed by an MPLS signaling pro… |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.1 | ColumnmplsTunnelIndex | not-accessible | current | Uniquely identifies this row. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.2 | ColumnmplsTunnelInstance | not-accessible | current | Uniquely identifies an instance of a tunnel. It is useful to identify multiple instances of tunnels for the purposes of backup and parallel tunnels. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.3 | ColumnmplsTunnelIngressLSRId | not-accessible | current | The purpose of this object is to uniquely identity a tunnel within a network. When the MPLS signalling protoocol is rsvp(2) this value SHOULD mimic the Extende… |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.4 | ColumnmplsTunnelEgressLSRId | not-accessible | current | Specifies the egress LSR ID. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.5 | ColumnmplsTunnelName | read-create | current | The canonical name assigned to the tunnel. This name can be used to refer to the tunnel on the LSR's console port. If mplsTunnelIsIf is set to true then the if… |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.6 | ColumnmplsTunnelDescr | read-create | current | A textual string containing information about the tunnel. If there is no description this object contains a zero length string. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.7 | ColumnmplsTunnelIsIf | read-create | current | Denotes whether or not this tunnel corresponds to an interface represented in the interfaces group table. Note that if this variable is set to true then the if… |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.8 | ColumnmplsTunnelIfIndex | read-only | current | If mplsTunnelIsIf is set to true, then this value contains the LSR-assigned ifIndex which corresponds to an entry in the interfaces table. Otherwise this varia… |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.9 | ColumnmplsTunnelXCPointer | read-create | current | This variable points to a row in the mplsXCTable. This table identifies the segments that compose this tunnel, their characteristics, and relationships to each… |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.10 | ColumnmplsTunnelSignallingProto | read-create | current | The signaling protocol, if any, which was used to setup this tunnel. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.11 | ColumnmplsTunnelSetupPrio | read-create | current | Indicates the setup priority of this tunnel. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.12 | ColumnmplsTunnelHoldingPrio | read-create | current | Indicates the holding priority for this tunnel. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.13 | ColumnmplsTunnelSessionAttributes | read-create | current | This bitmask indicates optional session values for this tunnel. The following describes these bitfields: fastRerouteThis flag indicates that the any tunnel hop… |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.14 | ColumnmplsTunnelOwner | read-create | current | Indicates which protocol created and is responsible for managing this tunnel. Values rsvp(2) and crldp(3) should not be used at the head-end of a MPLS tunnel. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.15 | ColumnmplsTunnelLocalProtectInUse | read-create | current | Indicates that the local repair mechanism is in use to maintain this tunnel (usually in the face of an outage of the link it was previously routed over). |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.16 | ColumnmplsTunnelResourcePointer | read-create | current | This variable represents a pointer to the traffic parameter specification for this tunnel. This value may point at an entry in the mplsTunnelResourceEntry to i… |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.17 | ColumnmplsTunnelInstancePriority | read-create | current | This value indicates which priority, in descending order, with 0 indicating the lowest priority, within a group of tunnel instances. A group of tunnel instance… |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.18 | ColumnmplsTunnelHopTableIndex | read-create | current | Index into the mplsTunnelHopTable entry that specifies the explicit route hops for this tunnel. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.19 | ColumnmplsTunnelARHopTableIndex | read-only | current | Index into the mplsTunnelARHopTable entry that specifies the actual hops traversed by the tunnel. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.20 | ColumnmplsTunnelCHopTableIndex | read-only | current | Index into the mplsTunnelCHopTable entry that specifies the computed hops traversed by the tunnel. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.21 | ColumnmplsTunnelPrimaryInstance | read-only | current | Specifies the instance index of the primary instance of this tunnel. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.22 | ColumnmplsTunnelPrimaryTimeUp | read-only | current | Specifies the total time the primary instance of this tunnel has been active. The primary instance of this tunnel is defined in mplsTunnelPrimaryInstance. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.23 | ColumnmplsTunnelPathChanges | read-only | current | Specifies the number of times the paths has changed for this tunnel. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.24 | ColumnmplsTunnelLastPathChange | read-only | current | Specifies the time since the last path change for this tunnel. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.25 | ColumnmplsTunnelCreationTime | read-only | current | Specifies the value of SysUpTime when the first instance of this tunnel came into existence. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.26 | ColumnmplsTunnelStateTransitions | read-only | current | Specifies the number of times the state of this tunnel instance has changed. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.27 | ColumnmplsTunnelIncludeAnyAffinity | read-create | current | A link satisfies the include-any constraint if and only if the constraint is zero, or the link and the constraint have a resource class in common. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.28 | ColumnmplsTunnelIncludeAllAffinity | read-create | current | A link satisfies the include-all constraint if and only if the link contains all of the adminstrative groups specified in the constraint. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.29 | ColumnmplsTunnelExcludeAllAffinity | read-create | current | A link satisfies the exclude-all constraint if and only if the link contains none of the adminstrative groups specifie in the constraint. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.30 | ColumnmplsTunnelPathInUse | read-create | current | This value denotes the configured path that was chosen for this tunnel. This value reflects the secondary index into mplsTunnelHopTable. This path may not exac… |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.31 | ColumnmplsTunnelRole | read-create | current | This value signifies the role that this tunnel entry/instance represents. This value MUST be set to head(1) at the originating point of the tunnel. This value … |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.32 | ColumnmplsTunnelTotalUpTime | read-create | current | This value represents the aggregate up time for all instances of this tunnel, if available. If this value is unavailable, it MUST return a value of 0. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.33 | ColumnmplsTunnelInstanceUpTime | read-create | current | This value identifies the total time that this tunnel instance's operStatus has been Up(1). |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.34 | ColumnmplsTunnelAdminStatus | read-create | current | Indicates the desired operational status of this tunnel. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.35 | ColumnmplsTunnelOperStatus | read-only | current | Indicates the actual operational status of this tunnel, which is typically but not limited to, a function of the state of individual segments of this tunnel. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.36 | ColumnmplsTunnelRowStatus | read-create | current | This variable is used to create, modify, and/or delete a row in this table. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.37 | ColumnmplsTunnelStorageType | read-create | current | This variable indicates the storage type for this object. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.3 | ScalarmplsTunnelHopListIndexNext | read-only | current | This object contains an appropriate value to be used for mplsTunnelHopListIndex when creating entries in the mplsTunnelHopTable. If the number of unassigned en… |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.4 | TablemplsTunnelHopTable | not-accessible | current | The mplsTunnelHopTable is used to indicate the hops, strict or loose, for an MPLS tunnel defined in mplsTunnelTable, when it is established via signaling, for … |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.4.1 | RowmplsTunnelHopEntry | not-accessible | current | An entry in this table represents a tunnel hop. An entry is created by a network administrator for signaled ERLSP set up by an MPLS signaling protocol. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.4.1.1 | ColumnmplsTunnelHopListIndex | not-accessible | current | Primary index into this table identifying a particular explicit route object. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.4.1.2 | ColumnmplsTunnelHopPathOptionIndex | not-accessible | current | Secondary index into this table identifying a particular group of hops representing a particular configured path. This is otherwise known as a path option. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.4.1.3 | ColumnmplsTunnelHopIndex | not-accessible | current | Secondary index into this table identifying a particular hop. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.4.1.4 | ColumnmplsTunnelHopAddrType | read-create | current | Denotes the address type of this tunnel hop. Note that lspId(4) is a valid option only for tunnels signaled via CRLDP. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.4.1.5 | ColumnmplsTunnelHopIpv4Addr | read-create | current | If mplsTunnelHopAddrType is set to ipV4(1), then this value will contain the IPv4 address of this hop. If mplsTunnelHopAddrType is set to lspid(4), then this v… |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.4.1.6 | ColumnmplsTunnelHopIpv4PrefixLen | read-create | current | If mplsTunnelHopAddrType is ipV4(1), then the prefix length for this hop's IPv4 address is contained herein. This object is otherwise insignificant and should … |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.4.1.7 | ColumnmplsTunnelHopIpv6Addr | read-create | current | If the mplsTunnelHopAddrType is set to ipV6(2), then this variable contains the IPv6 address of this hop. This object is otherwise insignificant and should con… |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.4.1.8 | ColumnmplsTunnelHopIpv6PrefixLen | read-create | current | If mplsTunnelHopAddrType is set to ipV6(2), this value will contain the prefix length for this hop's IPv6 address. This object is otherwise insignificant and s… |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.4.1.9 | ColumnmplsTunnelHopAsNumber | read-create | current | If mplsTunnelHopAddrType is set to asNumber(3), then this value will contain the AS number of this hop. This object is otherwise insignificant and should conta… |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.4.1.10 | ColumnmplsTunnelHopLspId | read-create | current | If mplsTunnelHopAddrType is set to lspid(4), then this value will contain the LSPID of a tunnel of this hop. The present tunnel being configured is tunneled th… |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.4.1.11 | ColumnmplsTunnelHopType | read-create | current | Denotes whether this tunnel hop is routed in a strict or loose fashion. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.4.1.12 | ColumnmplsTunnelHopIncludeExclude | read-create | current | If this value is set to include(1), then this indicates that this hop must be included in the tunnel's path. If this value is set to exclude(2), then this hop … |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.4.1.13 | ColumnmplsTunnelHopPathOptionName | read-create | current | The description of this series of hops as they relate to the specified path option. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.4.1.14 | ColumnmplsTunnelHopEntryPathComp | read-create | current | If this value is set to dynamic, then the user should only specify the source and destination of the path and expect that the CSPF will calculate the remainder… |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.4.1.15 | ColumnmplsTunnelHopRowStatus | read-create | current | This variable is used to create, modify, and/or delete a row in this table. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.4.1.16 | ColumnmplsTunnelHopStorageType | read-create | current | This variable indicates the storage type for this object. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.5 | ScalarmplsTunnelResourceIndexNext | read-only | current | This object contains the next appropriate value to be used for mplsTunnelResourceIndex when creating entries in the mplsTunnelResourceTable. If the number of u… |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.6 | TablemplsTunnelResourceTable | not-accessible | current | The mplsTunnelResourceTable allows a manager to specify which resources are desired for an MPLS tunnel. This table also allows several tunnels to point to a si… |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.6.1 | RowmplsTunnelResourceEntry | not-accessible | current | An entry in this table represents a set of resources for an MPLS tunnel. An entry can be created by a network administrator or by an SNMP agent as instructed b… |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.6.1.1 | ColumnmplsTunnelResourceIndex | not-accessible | current | Uniquely identifies this row. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.6.1.2 | ColumnmplsTunnelResourceMaxRate | read-create | current | The maximum rate in bits/second. Note that setting mplsTunnelResourceMaxRate, mplsTunnelResourceMeanRate, and mplsTunnelResourceMaxBurstSize to 0 indicates bes… |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.6.1.3 | ColumnmplsTunnelResourceMeanRate | read-create | current | This object is copied into an instance of mplsTrafficParamMeanRate in the mplsTrafficParamTable. The OID of this table entry is then copied into the correspond… |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.6.1.4 | ColumnmplsTunnelResourceMaxBurstSize | read-create | current | The maximum burst size in bytes. This object is copied to mplsInSegmentMaxBurstSize of the corresponding in-segment. When resource allocation is performed as r… |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.6.1.5 | ColumnmplsTunnelResourceMeanBurstSize | read-create | current | The mean burst size in bytes. The implementations which do not implement this variable must return 0 for this value and must not allow a user to set this value. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.6.1.6 | ColumnmplsTunnelResourceExcessBurstSize | read-create | current | The Excess burst size in bytes. The implementations which do not implement this variable must return 0 for this value and must not allow a user to set this val… |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.6.1.7 | ColumnmplsTunnelResourceFrequency | read-create | current | The granularity of the availability of committed rate. The implementations which do not implement this variable must return unspecified(1) for this value and m… |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.6.1.8 | ColumnmplsTunnelResourceWeight | read-create | current | The relative weight for using excess bandwidth above its committed rate. The value of 0 means that weight is not applicable for the CR-LSP. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.6.1.9 | ColumnmplsTunnelResourceRowStatus | read-create | current | This variable is used to create, modify, and/or delete a row in this table. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.6.1.10 | ColumnmplsTunnelResourceStorageType | read-create | current | This variable indicates the storage type for this object. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.7 | TablemplsTunnelARHopTable | not-accessible | current | The mplsTunnelARHopTable is used to indicate the hops, strict or loose, for an MPLS tunnel defined in mplsTunnelTable, as reported by the MPLS signaling protoc… |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.7.1 | RowmplsTunnelARHopEntry | not-accessible | current | An entry in this table represents a tunnel hop. An entry is created by a network administrator for signaled ERLSP set up by an MPLS signaling protocol. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.7.1.1 | ColumnmplsTunnelARHopListIndex | not-accessible | current | Primary index into this table identifying a particular recorded hop list. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.7.1.2 | ColumnmplsTunnelARHopIndex | not-accessible | current | Secondary index into this table identifying the particular hop. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.7.1.3 | ColumnmplsTunnelARHopAddrType | read-only | current | Denotes the address type of this tunnel hop. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.7.1.4 | ColumnmplsTunnelARHopIpv4Addr | read-only | current | If mplsTunnelARHopAddrType is set to ipV4(1), then this value will contain the IPv4 address of this hop. This object is otherwise insignificant and should cont… |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.7.1.5 | ColumnmplsTunnelARHopIpv4PrefixLen | read-only | current | If mplsTunnelARHopAddrType is ipV4(1), then the prefix length for this hop's IPv4 address is contained herein. This object is otherwise insignificant and shoul… |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.7.1.6 | ColumnmplsTunnelARHopIpv6Addr | read-only | current | If the mplsTunnelARHopAddrType is set to ipV6(2), then this variable contains the IPv6 address of this hop. This object is otherwise insignificant and should c… |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.7.1.7 | ColumnmplsTunnelARHopIpv6PrefixLen | read-only | current | If mplsTunnelARHopAddrType is set to ipV6(2), this value will contain the prefix length for this hop's IPv6 address. This object is otherwise insignificant and… |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.7.1.8 | ColumnmplsTunnelARHopAsNumber | read-only | current | If mplsTunnelARHopAddrType is set to asNumber(3), then this value will contain the AS number of this hop. This object is otherwise insignificant and should con… |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.7.1.9 | ColumnmplsTunnelARHopLspId | read-only | current | If mplsTunnelARHopAddrType is set to lspid(4), then this value will contain the LSP ID of this hop. This object is otherwise insignificant and should contain a… |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.8 | TablemplsTunnelCHopTable | not-accessible | current | The mplsTunnelCHopTable is used to indicate the hops, strict or loose, for an MPLS tunnel defined in mplsTunnelTable, as computed by a constraint- based routin… |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.8.1 | RowmplsTunnelCHopEntry | not-accessible | current | An entry in this table represents a tunnel hop. An entry in this table is created by a constraint- based routing protocol based on the hops specified in the co… |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.8.1.1 | ColumnmplsTunnelCHopListIndex | not-accessible | current | Primary index into this table identifying a particular computed hop list. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.8.1.2 | ColumnmplsTunnelCHopIndex | not-accessible | current | Secondary index into this table identifying the particular hop. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.8.1.3 | ColumnmplsTunnelCHopAddrType | read-only | current | Denotes the address type of this tunnel hop. Note that lspId(4) is a valid option only for tunnels signaled via CRLDP. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.8.1.4 | ColumnmplsTunnelCHopIpv4Addr | read-only | current | If mplsTunnelCHopAddrType is set to ipV4(1), then this value will contain the IPv4 address of this hop. This object is otherwise insignificant and should conta… |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.8.1.5 | ColumnmplsTunnelCHopIpv4PrefixLen | read-only | current | If mplsTunnelCHopAddrType is ipV4(1), then the prefix length for this hop's IPv4 address is contained herein. This object is otherwise insignificant and should… |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.8.1.6 | ColumnmplsTunnelCHopIpv6Addr | read-only | current | If the mplsTunnelCHopAddrType is set to ipV6(2), then this variable contains the IPv6 address of this hop. This object is otherwise insignificant and should co… |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.8.1.7 | ColumnmplsTunnelCHopIpv6PrefixLen | read-only | current | If mplsTunnelCHopAddrType is set to ipV6(2), this value will contain the prefix length for this hop's IPv6 address. This object is otherwise insignificant and … |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.8.1.8 | ColumnmplsTunnelCHopAsNumber | read-only | current | If mplsTunnelCHopAddrType is set to asNumber(3), then this value will contain the AS number of this hop. This object is otherwise insignificant and should cont… |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.8.1.9 | ColumnmplsTunnelCHopLspId | read-only | current | If mplsTunnelCHopAddrType is set to lspid(4), then this value will contain the LSP ID of this hop. This object is otherwise insignificant and should contain a … |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.8.1.10 | ColumnmplsTunnelCHopType | read-only | current | Denotes whether this is tunnel hop is routed in a strict or loose fashion. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.9 | TablemplsTunnelPerfTable | not-accessible | current | This table provides per-tunnel MPLS performance information. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.9.1 | RowmplsTunnelPerfEntry | not-accessible | current | An entry in this table is created by the LSR for every tunnel. Its is an extension to mplsTunnelEntry. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.9.1.1 | ColumnmplsTunnelPerfPackets | read-only | current | Number of packets forwarded by the tunnel. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.9.1.2 | ColumnmplsTunnelPerfHCPackets | read-only | current | High capacity counter for number of packets forwarded by the tunnel. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.9.1.3 | ColumnmplsTunnelPerfErrors | read-only | current | Number of errored packets. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.9.1.4 | ColumnmplsTunnelPerfBytes | read-only | current | Number of bytes forwarded by the tunnel. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.9.1.5 | ColumnmplsTunnelPerfHCBytes | read-only | current | High capacity counter for number of bytes forwarded by the tunnel. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.10 | TablemplsTunnelCRLDPResTable | not-accessible | current | The mplsTunnelCRLDPResTable allows a manager to specify which CR-LDP-specific resources are desired for an MPLS tunnel if that tunnel is signaled using CR-LDP.… |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.10.1 | RowmplsTunnelCRLDPResEntry | not-accessible | current | An entry in this table represents a set of resources for an MPLS tunnel established using CRLDP (mplsTunnelSignallingProto equal to crldp (3)). An entry can be… |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.10.1.2 | ColumnmplsTunnelCRLDPResMeanBurstSize | read-create | current | The mean burst size in bytes. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.10.1.3 | ColumnmplsTunnelCRLDPResExcessBurstSize | read-create | current | The Excess burst size in bytes. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.10.1.4 | ColumnmplsTunnelCRLDPResFrequency | read-create | current | The granularity of the availability of committed rate. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.10.1.5 | ColumnmplsTunnelCRLDPResWeight | read-create | current | The relative weight for using excess bandwidth above its committed rate. The value of 0 means that weight is not applicable for the CR-LSP. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.10.1.6 | ColumnmplsTunnelCRLDPResFlags | read-create | current | The value of the 1 byte Flags conveyed as part of the traffic parameters during the establishment of the CRLSP. The bits in this object are to be interpreted a… |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.10.1.7 | ColumnmplsTunnelCRLDPResRowStatus | read-create | current | This variable is used to create, modify, and/or delete a row in this table. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.10.1.8 | ColumnmplsTunnelCRLDPResStorageType | read-create | current | This variable indicates the storage type for this object. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.11 | ScalarmplsTunnelTrapEnable | read-write | current | If this object is true, then it enables the generation of mplsTunnelUp and mplsTunnelDown traps, otherwise these traps are not emitted. |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.3 | NodemplsTeNotifications | |||
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.3.0 | NodemplsTeNotifyPrefix | |||
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.3.0.1 | NotificationmplsTunnelUp | current | This notification is generated when a mplsTunnelOperStatus object for one of the configured tunnels is about to leave the down state and transition into some o… | |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.3.0.2 | NotificationmplsTunnelDown | current | This notification is generated when a mplsTunnelOperStatus object for one of the configured tunnels is about to enter the down state from some other state (but… | |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.3.0.3 | NotificationmplsTunnelRerouted | current | This notification is generated when a tunnel is rerouted. If the actual path is used, then this tunnel's entry MAY contain the new path for this tunnel some ti… | |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.3.0.4 | NotificationmplsTunnelReoptimized | current | This notification is generated when a tunnel is reoptimized. If the actual path is used, then this tunnel's entry MAY contain the new path for this tunnel some… | |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.4 | NodemplsTeConformance | |||
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.4.1 | NodemplsTeGroups | |||
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.4.1.1 | GroupmplsTunnelGroup | current | Necessary, but not sufficient, set of objects to implement tunnels. In addition, depending on the type of the tunnels supported (for example, manually configur… | |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.4.1.2 | GroupmplsTunnelManualGroup | current | Object(s) needed to implement manually configured tunnels. | |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.4.1.3 | GroupmplsTunnelSignaledGroup | current | Object needed to implement signaled tunnels. | |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.4.1.4 | GroupmplsTunnelScalarGroup | current | Scalar object needed to implement MPLS tunnels. | |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.4.1.5 | GroupmplsTunnelIsIntfcGroup | current | Objects needed to implement tunnels that are interfaces. | |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.4.1.6 | GroupmplsTunnelIsNotIntfcGroup | current | Objects needed to implement tunnels that are not interfaces. | |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.4.1.7 | GroupmplsTunnelOptionalGroup | current | The objects in this group are optional. | |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.4.1.8 | GroupmplsTunnelCRLDPResOptionalGroup | current | Set of objects implemented for resources applicable for tunnels signaled using CR-LDP. | |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.4.1.9 | GroupmplsTeNotificationGroup | current | Set of notifications implemented in this module. None is mandatory. | |
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.4.2 | NodemplsTeCompliances | |||
| 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.4.2.1 | CompliancemplsTeModuleCompliance | read-only | current | Compliance statement for agents that support the MPLS TE MIB. |