HUAWEI-EQAM-AN-MIB
474 objects
The MIB is used for defining Huawei's EQAM attribute.
Imported Objects
| DOCS-IF3-MIB | ChannelList |
| HUAWEI-MIB | huaweiUtility |
| IF-MIB | ifIndex InterfaceIndex InterfaceIndexOrZero |
| INET-ADDRESS-MIB | InetAddress InetAddressType InetPortNumber |
| P-BRIDGE-MIB | EnabledStatus |
| Q-BRIDGE-MIB | VlanId |
| SNMPv2-CONF | NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Counter64 Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-IDENTITY OBJECT-TYPE TimeTicks Unsigned32 |
| SNMPv2-TC | DateAndTime DisplayString RowStatus TEXTUAL-CONVENTION TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.2011.6.187 | IdentityhwEqamAn | The MIB is used for defining Huawei's EQAM attribute. | ||
| 1.3.6.1.4.1.2011.6.187.1 | NodehwDocsQamVideoGlobalConfigObject | |||
| 1.3.6.1.4.1.2011.6.187.1.1 | ScalarhwDocsQamVideoTimeOutInterval | read-write | current | Indicates the video timeout interval. Default: 60 |
| 1.3.6.1.4.1.2011.6.187.1.2 | ScalarhwDocsQamAutoConfigIppoolAddressType | read-write | current | Indicates the address type of the address pool. Only IPv4 addresses are supported. |
| 1.3.6.1.4.1.2011.6.187.1.3 | ScalarhwDocsQamAutoConfigIppoolStartAddress | read-write | current | Indicates the start address of the address pool. To delete an IP address pool, bind hwDocsQamAutoConfigIppoolStartAddress and hwDocsQamAutoConfigIppoolEndAddre… |
| 1.3.6.1.4.1.2011.6.187.1.4 | ScalarhwDocsQamAutoConfigIppoolEndAddress | read-write | current | Indicates the end address of the address pool. To delete an IP address pool, bind hwDocsQamAutoConfigIppoolStartAddress and hwDocsQamAutoConfigIppoolEndAddress… |
| 1.3.6.1.4.1.2011.6.187.1.5 | ScalarhwDocsQamAutoConfigIppoolVlanId | read-write | current | Indicates the VLAN ID of the video domain. The default value is -1, indicating that the VLAN ID is invalid. |
| 1.3.6.1.4.1.2011.6.187.1.6 | ScalarhwDocsQamAutoConfigVideoProfile | read-write | current | Automatically pre-configures the name of the video profile. |
| 1.3.6.1.4.1.2011.6.187.1.8 | ScalarhwDocsQamMulticastVlanId | read-write | current | Indicates the multicast VLAN ID of the video service. The default value is -1, indicating that the multicast VLAN ID is invalid. |
| 1.3.6.1.4.1.2011.6.187.1.9 | ScalarhwDocsQamSecondaryMulticastVlanId | read-write | current | Indicates the secondary multicast VLAN ID. The default value is -1, indicating that the multicast VLAN ID is invalid. |
| 1.3.6.1.4.1.2011.6.187.1.10 | ScalarhwDocsQamGratuitousArpPeriodSendMode | read-write | current | Indicates the gratuitous ARP period send mode, the default value is disabled(2). Options: 1. enabled(1) -indicates the gratuitous ARP period send mode is enabl… |
| 1.3.6.1.4.1.2011.6.187.1.11 | ScalarhwDocsQamDVBProcessFrameSlot | read-write | current | Indicates the frame ID and slot ID of the DVB service processing board. The most significant 16 bits indicate the frame ID while the least significant 16 bits … |
| 1.3.6.1.4.1.2011.6.187.1.12 | ScalarhwDocsQamInputTSDefaultSwitchoverTriggers | read-write | current | Indicates the default trigger conditions for protection switching on input TSs. The format is 4 bits. A bit of this attribute is set to 1 if the parameter indi… |
| 1.3.6.1.4.1.2011.6.187.1.13 | ScalarhwDocsQamInputTSStatisticsClearAll | read-write | current | Clears all the input TS statistics. The default value is clearStatistic(1). |
| 1.3.6.1.4.1.2011.6.187.1.14 | ScalarhwDocsQamVideoProgramNumberTotalGlobal | read-only | current | Indicates the number of global VOD programs. |
| 1.3.6.1.4.1.2011.6.187.1.15 | ScalarhwDocsQamVideoProgramNumberOnlineGlobal | read-only | current | Indicates the number of global online VOD programs. |
| 1.3.6.1.4.1.2011.6.187.1.16 | ScalarhwDocsQamDVBChannelMonitoringProbeDuration | read-write | current | Indicates the duration of DVB channel monitoring. The default value is 60. |
| 1.3.6.1.4.1.2011.6.187.2 | TablehwDocsQamVideoProfileTable | not-accessible | current | Indicates the video profile table used to manage information including video mapping. The index of this table is hwDocsQamVideoProfileName. |
| 1.3.6.1.4.1.2011.6.187.2.1 | RowhwDocsQamVideoProfileEntry | not-accessible | current | Indicates the video profile table used to manage information including video mapping. The index of this entry is hwDocsQamVideoProfileName. |
| 1.3.6.1.4.1.2011.6.187.2.1.1 | ColumnhwDocsQamVideoProfileName | not-accessible | current | Indicates the video profile name. |
| 1.3.6.1.4.1.2011.6.187.2.1.2 | ColumnhwDocsQamVideoProfileRowStatus | read-create | current | Row status, used to query, create, modify, and delete a video profile table. It supports the active(1), createAndGo(4), and destroy(6) operations. During query… |
| 1.3.6.1.4.1.2011.6.187.3 | TablehwDocsQamVideoMapTable | not-accessible | current | Indicates the video mapping table used to configure the mapping between video streams and cable channels. The indexes of this table are hwDocsQamVideoProfileNa… |
| 1.3.6.1.4.1.2011.6.187.3.1 | RowhwDocsQamVideoMapEntry | not-accessible | current | Indicates the video mapping table used to configure the mapping between video streams and cable channels. The indexes of this entry are hwDocsQamVideoProfileNa… |
| 1.3.6.1.4.1.2011.6.187.3.1.1 | ColumnhwDocsQamVideoMapIndex | not-accessible | current | Indicates the index of a video mapping table. You can also fill 4294967295 and the system will automatically allocate an index. |
| 1.3.6.1.4.1.2011.6.187.3.1.2 | ColumnhwDocsQamVideoMapUdpPort | read-create | current | Indicates the UDP port number. The default value is 0, indicating that the UDP port number is invalid. Range: 0-65535 |
| 1.3.6.1.4.1.2011.6.187.3.1.3 | ColumnhwDocsQamVideoMapStreamType | read-create | current | Indicates the program stream type. Options: 1. data(1) -indicates the data type 2. spts(2) -indicates the spts type 3. mpts(3) -indicates the mpts type 4. plan… |
| 1.3.6.1.4.1.2011.6.187.3.1.4 | ColumnhwDocsQamVideoMapInputProgram | read-create | current | Indicates the program ID of the input stream. The default value is -1, indicating that the program ID is ignored. |
| 1.3.6.1.4.1.2011.6.187.3.1.5 | ColumnhwDocsQamVideoMapOutputProgram | read-create | current | Indicates the program ID of the output stream. The default value is -1, indicating that the program ID is ignored. |
| 1.3.6.1.4.1.2011.6.187.3.1.6 | ColumnhwDocsQamVideoMapJitter | read-create | current | Indicates the network jitter allowed. If hwDocsQamVideoMapStreamType is data or mpts, the default value is -1, indicating that network jitter is ignored. If hw… |
| 1.3.6.1.4.1.2011.6.187.3.1.7 | ColumnhwDocsQamVideoMapPmtPid | read-create | current | Indicates the PMT PID of the output program. If hwDocsQamVideoMapStreamType is data or hwDocsQamVideoMapStreamType is mpts and hwDocsQamVideoMapMode is passthr… |
| 1.3.6.1.4.1.2011.6.187.3.1.8 | ColumnhwDocsQamVideoMapChannelList | read-create | current | Indicates the channel list for output videos. |
| 1.3.6.1.4.1.2011.6.187.3.1.9 | ColumnhwDocsQamVideoMapRowStatus | read-create | current | Row status, used to query, create, modify, and delete a video mapping table. It supports the active(1), createAndGo(4), and destroy(6) operations. During query… |
| 1.3.6.1.4.1.2011.6.187.3.1.12 | ColumnhwDocsQamVideoMapMode | read-create | current | Indicates the video stream map mode, the default value is invalid(255). Options: 1. passthrough(1) -indicates the MPTS video stream mode is passthrough. When v… |
| 1.3.6.1.4.1.2011.6.187.3.1.13 | ColumnhwDocsQamVideoMapNITRemap | read-create | current | Indicates the output NIT PID which the input NIT PID mapped to. If hwDocsQamVideoMapStreamType is not mpts, the default value is always -1, indicating that the… |
| 1.3.6.1.4.1.2011.6.187.3.1.14 | ColumnhwDocsQamVideoMapFilterPIDList | read-create | current | Indicates the filter PID list which are not allowed to forward. Filter PID consists of two bytes and no greater than 8190. Max of 32 filter PIDs can be configu… |
| 1.3.6.1.4.1.2011.6.187.3.1.15 | ColumnhwDocsQamVideoMapInputTsIndex | read-create | current | Indicates the index of the transport stream, the default value is -1, indicating that the index of the transport stream is ignored. |
| 1.3.6.1.4.1.2011.6.187.3.1.16 | ColumnhwDocsQamVideoMapProgramName | read-create | current | Indicates the name of an output program in video mapping. The default value is a null string, which indicates that the name of the input program is inherited. |
| 1.3.6.1.4.1.2011.6.187.3.1.17 | ColumnhwDocsQamVideoMapEnable | read-create | current | Indicates the enabling status of video mapping. If hwDocsQamVideoMapStreamType is mpts, this value can be set to true or false; if hwDocsQamVideoMapStreamType … |
| 1.3.6.1.4.1.2011.6.187.3.1.18 | ColumnhwDocsQamVideoMapPIDKeepOriginal | read-create | current | Indicates the keeping program PID original of video mapping. If hwDocsQamVideoMapMode is remap, this value can be set to true or false; if hwDocsQamVideoMapMod… |
| 1.3.6.1.4.1.2011.6.187.4 | TablehwDocsQamVideoDomainTable | not-accessible | current | Indicates the video domain table used to manage information, such as EQAM's IP address. The index of this table is hwDocsQamVideoDomainName. |
| 1.3.6.1.4.1.2011.6.187.4.1 | RowhwDocsQamVideoDomainEntry | not-accessible | current | Indicates the video domain table used to manage information, such as EQAM's IP address. The index of this entry is hwDocsQamVideoDomainName. |
| 1.3.6.1.4.1.2011.6.187.4.1.1 | ColumnhwDocsQamVideoDomainName | not-accessible | current | Indicates the video domain name. |
| 1.3.6.1.4.1.2011.6.187.4.1.2 | ColumnhwDocsQamVideoDomainLocalIpAddress | read-create | current | Indicates the local IP address of the video domain. |
| 1.3.6.1.4.1.2011.6.187.4.1.3 | ColumnhwDocsQamVideoDomainLocalIpAddressType | read-create | current | Indicates the local IP address type of the local end. |
| 1.3.6.1.4.1.2011.6.187.4.1.4 | ColumnhwDocsQamVideoDomainLocalVlanID | read-create | current | Indicates the local VLAN ID of the video domain. The default value is -1, indicating that the local VLAN ID is invalid. |
| 1.3.6.1.4.1.2011.6.187.4.1.5 | ColumnhwDocsQamVideoDomainRowStatus | read-create | current | Row status, used to query, create, modify, and delete a video domain table. It supports the active(1), createAndGo(4), and destroy(6) operations. During query,… |
| 1.3.6.1.4.1.2011.6.187.4.1.7 | ColumnhwDocsQamVideoDomainUDPPortStep | read-create | current | Indicates the step of udp port. The default value is 512. |
| 1.3.6.1.4.1.2011.6.187.4.1.8 | ColumnhwDocsQamVideoDomainBindVideoProfile | read-create | current | Indicates the bind video profile name. |
| 1.3.6.1.4.1.2011.6.187.6 | TablehwDocsQamChannelProfileTable | not-accessible | current | Indicates the EQAM channel profile table used for managing parameters related to channels. The index of this table is hwDocsQamChannelProfileName. |
| 1.3.6.1.4.1.2011.6.187.6.1 | RowhwDocsQamChannelProfileEntry | not-accessible | current | Indicates the EQAM channel profile table used for managing parameters related to channels. The index of this entry is hwDocsQamChannelProfileName. |
| 1.3.6.1.4.1.2011.6.187.6.1.1 | ColumnhwDocsQamChannelProfileName | not-accessible | current | Indicates the name of the channel profile table. |
| 1.3.6.1.4.1.2011.6.187.6.1.2 | ColumnhwDocsQamChannelProfileTransportStreamID | read-create | current | Indicates the transport stream ID. |
| 1.3.6.1.4.1.2011.6.187.6.1.3 | ColumnhwDocsQamChannelProfilePATSendPeriod | read-create | current | Indicates the PAT send interval. |
| 1.3.6.1.4.1.2011.6.187.6.1.4 | ColumnhwDocsQamChannelProfilePMTSendPeriod | read-create | current | Indicates the PMT send interval. |
| 1.3.6.1.4.1.2011.6.187.6.1.5 | ColumnhwDocsQamChannelProfileRowStatus | read-create | current | Row status, used to query, create, modify, and delete a channel profile table. It supports the active(1), createAndGo(4), and destroy(6) operations. During que… |
| 1.3.6.1.4.1.2011.6.187.7 | TablehwDocsQamDChannelBindTable | not-accessible | current | Indicates the EQAM channel binding table used for managing binding relationships between channel profiles and channel IDs. The index of this table is ifIndex. |
| 1.3.6.1.4.1.2011.6.187.7.1 | RowhwDocsQamDChannelBindEntry | not-accessible | current | Indicates the EQAM channel binding table used for managing binding relationships between channel profiles and channel IDs. The index of this entry is ifIndex. |
| 1.3.6.1.4.1.2011.6.187.7.1.1 | ColumnhwDocsQamDChannelBindProfileName | read-create | current | Indicates the channel profile name. hwDocsQamChannelProfileTable is a reference for setting parameters in the profile. |
| 1.3.6.1.4.1.2011.6.187.8 | TablehwDocsQamVideoStreamTable | not-accessible | current | Indicates the dynamic video stream information table used for obtaining dynamic video stream information. The indexes of this table are ifIndex and hwDocsQamVi… |
| 1.3.6.1.4.1.2011.6.187.8.1 | RowhwDocsQamVideoStreamEntry | not-accessible | current | Indicates the dynamic video stream information table used for obtaining dynamic video stream information. The indexes of this entry are ifIndex and hwDocsQamVi… |
| 1.3.6.1.4.1.2011.6.187.8.1.1 | ColumnhwDocsQamVideoStreamIndex | not-accessible | current | Indicates the index of a dynamic video stream information table. |
| 1.3.6.1.4.1.2011.6.187.8.1.2 | ColumnhwDocsQamVideoStreamDestinationIpAddress | read-only | current | Indicates the destination IP address. |
| 1.3.6.1.4.1.2011.6.187.8.1.3 | ColumnhwDocsQamVideoStreamDestinationIpAddressType | read-only | current | Indicates the destination IP address type. |
| 1.3.6.1.4.1.2011.6.187.8.1.4 | ColumnhwDocsQamVideoStreamDestinationUdpPort | read-only | current | Indicates the destination UDP port number. The default value is 0, indicating that the UDP port number is invalid. Range: 0-65535 |
| 1.3.6.1.4.1.2011.6.187.8.1.5 | ColumnhwDocsQamVideoStreamType | read-only | current | Indicates the data flow type. Options: 1. data(1) -indicates the data type 2. spts(2) -indicates the spts type 3. mpts(3) -indicates the mpts type 4. plant(4) … |
| 1.3.6.1.4.1.2011.6.187.8.1.6 | ColumnhwDocsQamVideoStreamJitter | read-only | current | Indicates the network jitter allowed. If the current video stream is not supported, -1 is returned. |
| 1.3.6.1.4.1.2011.6.187.8.1.7 | ColumnhwDocsQamVideoStreamState | read-only | current | Indicates the video stream status. Options: 1. offline(1) -indicates the offline state 2. online(2) -indicates the online state 3. unknown(3) -indicates the un… |
| 1.3.6.1.4.1.2011.6.187.8.1.8 | ColumnhwDocsQamVideoStreamInputStreamID | read-only | current | Indicates the input transport stream ID, the value -1 indicates that the input transport stream ID is invalid. |
| 1.3.6.1.4.1.2011.6.187.8.1.9 | ColumnhwDocsQamVideoStreamInputProgram | read-only | current | Indicates the input program ID, the value -1 indicates that the input program ID is invalid. |
| 1.3.6.1.4.1.2011.6.187.8.1.10 | ColumnhwDocsQamVideoStreamInputPMTPID | read-only | current | Indicates the input PMT PID, the value -1 indicates that the input PMT PID is invalid. |
| 1.3.6.1.4.1.2011.6.187.8.1.11 | ColumnhwDocsQamVideoStreamInputPCRPID | read-only | current | Indicates the input PCR PID, the value -1 indicates that the input PCR PID is invalid. |
| 1.3.6.1.4.1.2011.6.187.8.1.12 | ColumnhwDocsQamVideoStreamOutputStreamID | read-only | current | Indicates the output transport stream ID, the value -1 indicates that the output transport stream ID is invalid. |
| 1.3.6.1.4.1.2011.6.187.8.1.13 | ColumnhwDocsQamVideoStreamOutputProgram | read-only | current | Indicates the program ID of the output stream, the value -1 indicates that the program ID of the output stream is invalid. |
| 1.3.6.1.4.1.2011.6.187.8.1.14 | ColumnhwDocsQamVideoStreamOutputPMTPID | read-only | current | Indicates the PMT PID of the output stream, the value -1 indicates that the PMT PID of the output stream is invalid. |
| 1.3.6.1.4.1.2011.6.187.8.1.15 | ColumnhwDocsQamVideoStreamOutputPCRPID | read-only | current | Indicates the PCR PID of the output stream, the value -1 indicates that the PCR PID of the output stream is invalid. |
| 1.3.6.1.4.1.2011.6.187.8.1.16 | ColumnhwDocsQamVideoStreamInputESPIDList | read-only | current | Indicates the ESPID list for input streams. PID consists of two bytes and must be in one-to-one mapping with ESTypeList. |
| 1.3.6.1.4.1.2011.6.187.8.1.17 | ColumnhwDocsQamVideoStreamOutputESPIDList | read-only | current | Indicates the ESPID list for output streams. PID consists of two bytes and must be in one-to-one mapping with ESTypeList. |
| 1.3.6.1.4.1.2011.6.187.8.1.18 | ColumnhwDocsQamVideoStreamESTypeList | read-only | current | Indicate the ES type list. One byte indicates a type, which must be in one-to-one mapping with the ESPID list for input or output streams. |
| 1.3.6.1.4.1.2011.6.187.8.1.19 | ColumnhwDocsQamVideoStreamChannelList | read-only | current | Indicates the output channel list. |
| 1.3.6.1.4.1.2011.6.187.8.1.20 | ColumnhwDocsQamVideoStreamTraffic | read-only | current | Indicates the video stream traffic. |
| 1.3.6.1.4.1.2011.6.187.8.1.26 | ColumnhwDocsQamVideoStreamSourceIpAddressType | read-create | current | Indicates the address type of the source IP address in video stream. Only IPv4 addresses are supported. |
| 1.3.6.1.4.1.2011.6.187.8.1.27 | ColumnhwDocsQamVideoStreamSourceIpAddress | read-create | current | Indicates the source IP address of the video stream. |
| 1.3.6.1.4.1.2011.6.187.8.1.28 | ColumnhwDocsQamVideoStreamDiscontinuityCounter | read-only | current | Indicates the discontinuity counter of video stream. Default: 0 |
| 1.3.6.1.4.1.2011.6.187.8.1.29 | ColumnhwDocsQamVideoStreamSrambled | read-only | current | Indicates whether a VOD program is scrambled. If one ES is scrambled, the entire program is scrambled. Default: false(2). |
| 1.3.6.1.4.1.2011.6.187.8.1.30 | ColumnhwDocsQamVideoStreamESSrambleStateList | read-only | current | Indicates the sramble type mask of the video stream ES. The default value is an empty character string, indicating no sramble type list mask. Format: 2 bytes i… |
| 1.3.6.1.4.1.2011.6.187.9 | TablehwDocsQamVideoInputStreamStatisticsTable | not-accessible | current | Indicates the input statistics table for dynamic video streams. The indexes of this table are ifIndex and hwDocsQamVideoInputStreamStatisticsIndex. |
| 1.3.6.1.4.1.2011.6.187.9.1 | RowhwDocsQamVideoInputStreamStatisticsEntry | not-accessible | current | Indicates the input statistics table for dynamic video streams. The indexes of this entry are ifIndex and hwDocsQamVideoInputStreamStatisticsIndex. |
| 1.3.6.1.4.1.2011.6.187.9.1.1 | ColumnhwDocsQamVideoInputStreamStatisticsIndex | not-accessible | current | Indicates the index of input statistics table for dynamic video streams. |
| 1.3.6.1.4.1.2011.6.187.9.1.2 | ColumnhwDocsQamVideoInputStreamOperMode | read-write | current | Indicates the operation mode. The set operation can clear input statistics for dynamic video streams. Options: 1. clearStatistic(1) -indicates clearing input s… |
| 1.3.6.1.4.1.2011.6.187.9.1.3 | ColumnhwDocsQamVideoInputStreamPackets | read-only | current | Indicates packet statistics for input streams. |
| 1.3.6.1.4.1.2011.6.187.9.1.4 | ColumnhwDocsQamVideoInputStreamCountOfJitterOverflow | read-only | current | Indicates the jitter overflow statistics. |
| 1.3.6.1.4.1.2011.6.187.9.1.5 | ColumnhwDocsQamVideoInputStreamCountOfJitterUnderflow | read-only | current | Indicates the jitter underflow statistics. |
| 1.3.6.1.4.1.2011.6.187.9.1.6 | ColumnhwDocsQamVideoInputTSDiscontinuityCounter | read-only | current | Indicates the discontinuity counter of input streams. |
| 1.3.6.1.4.1.2011.6.187.10 | TablehwDocsQamVideoOutputDChannelStatisticsTable | not-accessible | current | Indicates the output channel statistics table for dynamic video streams. The index of this table is ifIndex. |
| 1.3.6.1.4.1.2011.6.187.10.1 | RowhwDocsQamVideoOutputDChannelStatisticsEntry | not-accessible | current | Indicates the output channel statistics table for dynamic video streams. The index of this entry is ifIndex. |
| 1.3.6.1.4.1.2011.6.187.10.1.1 | ColumnhwDocsQamVideoOutputDChannelOperMode | read-write | current | Indicates the operation mode. The set operation can clear output channel statistics for dynamic video streams. Options: 1. clearStatistic(1) -indicates clearin… |
| 1.3.6.1.4.1.2011.6.187.10.1.2 | ColumnhwDocsQamVideoOutputDChannelPackets | read-only | current | Indicates the packet statistics for output channels. |
| 1.3.6.1.4.1.2011.6.187.10.1.3 | ColumnhwDocsQamVideoOutputDChannelDiscardPackets | read-only | current | Indicates the packet loss statistics for output channels. |
| 1.3.6.1.4.1.2011.6.187.10.1.4 | ColumnhwDocsQamVideoOutputDChannelPATNumber | read-only | current | Indicates the PAT statistics for output channels. |
| 1.3.6.1.4.1.2011.6.187.10.1.5 | ColumnhwDocsQamVideoOutputDChannelPMTNumber | read-only | current | Indicates the PMT statistics for output channels. |
| 1.3.6.1.4.1.2011.6.187.10.1.6 | ColumnhwDocsQamVideoOutputDChannelCATNumber | read-only | current | Indicates the CAT statistics for output channels. |
| 1.3.6.1.4.1.2011.6.187.11 | TablehwDocsQamNGODEdgeDeviceTable | not-accessible | current | Indicates the edge device table. The index of this table is hwDocsQamNGODEdgeDeviceName. |
| 1.3.6.1.4.1.2011.6.187.11.1 | RowhwDocsQamNGODEdgeDeviceEntry | not-accessible | current | Indicates the edge device table. The index of this entry is hwDocsQamNGODEdgeDeviceName. |
| 1.3.6.1.4.1.2011.6.187.11.1.1 | ColumnhwDocsQamNGODEdgeDeviceName | not-accessible | current | This attribute is the key that identifies the instance of the edge device. Suggested format <RegionName>.<localname>. |
| 1.3.6.1.4.1.2011.6.187.11.1.2 | ColumnhwDocsQamNGODEdgeDeviceStreamingZone | read-create | current | This attribute identifies the streaming zone name which the edge device belongs to. Suggested format <RegionName>.<localname>. Null string means that the edge … |
| 1.3.6.1.4.1.2011.6.187.11.1.3 | ColumnhwDocsQamNGODEdgeDevicePeerAddressType | read-create | current | This attribute identifies the IP address type of ERM peer which the edge device setting up VREP session with. |
| 1.3.6.1.4.1.2011.6.187.11.1.4 | ColumnhwDocsQamNGODEdgeDevicePeerAddress | read-create | current | This attribute identifies the IP address of ERM peer which the edge device setting up VREP session with. |
| 1.3.6.1.4.1.2011.6.187.11.1.5 | ColumnhwDocsQamNGODEdgeDevicePeerPort | read-create | current | This attribute identifies the TCP port number of ERM peer which the edge device setting up VREP session with. The default port number is 6069. |
| 1.3.6.1.4.1.2011.6.187.11.1.6 | ColumnhwDocsQamNGODEdgeDeviceLocalAddressType | read-create | current | This attribute identifies the IP address type of the edge device to setup VREP session. |
| 1.3.6.1.4.1.2011.6.187.11.1.7 | ColumnhwDocsQamNGODEdgeDeviceLocalAddress | read-create | current | This attribute identifies the IP address of the edge device to setup VREP session. |
| 1.3.6.1.4.1.2011.6.187.11.1.8 | ColumnhwDocsQamNGODEdgeDeviceVREPIDMode | read-create | current | This attribute identifies the IP address type of the edge device to setup VREP session.. The default value is localip(1). Options: 1. localip(1) -indicates the… |
| 1.3.6.1.4.1.2011.6.187.11.1.9 | ColumnhwDocsQamNGODEdgeDeviceVREPID | read-create | current | This attribute identifies the VREPID value of the edge device. The VREP Identifier MUST uniquely identify this speaker/listener within its Streaming Zone. A gi… |
| 1.3.6.1.4.1.2011.6.187.11.1.10 | ColumnhwDocsQamNGODEdgeDeviceHoldTime | read-create | current | This attribute identifies the number of seconds that the edge device proposes for the value of the Hold Timer. Upon receipt of an OPEN message, a VREP speaker … |
| 1.3.6.1.4.1.2011.6.187.11.1.11 | ColumnhwDocsQamNGODEdgeDeviceConnectRetry | read-create | current | This attribute identifies the expire time for the edge device to setup an TCP connection. The exact value of the ConnectRetry timer is a local matter, but shou… |
| 1.3.6.1.4.1.2011.6.187.11.1.12 | ColumnhwDocsQamNGODEdgeDeviceActive | read-write | current | This attribute identifies the state of the edge device. Set ture to active the edge device and false to deactive. The default value is false. |
| 1.3.6.1.4.1.2011.6.187.11.1.13 | ColumnhwDocsQamNGODEdgeDeviceState | read-only | current | Indicates the state of the edge device VREP FSM. Options: 1. idle(1) -Initially VREP is in the Idle state for each peer 2. connect(2) -In this state, an edge d… |
| 1.3.6.1.4.1.2011.6.187.11.1.14 | ColumnhwDocsQamNGODEdgeDeviceNegotiatedHoldTime | read-only | current | This attribute identifies the negotiated number of seconds that the edge device proposes for the value of the Hold Timer. See hwDocsQamNGODEdgeDeviceHoldTime d… |
| 1.3.6.1.4.1.2011.6.187.11.1.15 | ColumnhwDocsQamNGODEdgeDeviceEstablishedPeerAddressType | read-only | current | This attribute identifies the IP address type of ERM peer which the edge device established a VREP session with. |
| 1.3.6.1.4.1.2011.6.187.11.1.16 | ColumnhwDocsQamNGODEdgeDeviceEstablishedPeerAddress | read-only | current | This attribute identifies the IP address of ERM peer which the edge device established a VREP session with. When VREP session is not in established state, this… |
| 1.3.6.1.4.1.2011.6.187.11.1.17 | ColumnhwDocsQamNGODEdgeDeviceEstablishedPeerPort | read-only | current | This attribute identifies the TCP port number of ERM peer which the edge device established a VREP session with. When VREP session is not in established state,… |
| 1.3.6.1.4.1.2011.6.187.11.1.18 | ColumnhwDocsQamNGODEdgeDeviceEstablishedLocalAddressType | read-only | current | This attribute identifies the IP address type of the edge device established a VREP session. |
| 1.3.6.1.4.1.2011.6.187.11.1.19 | ColumnhwDocsQamNGODEdgeDeviceEstablishedLocalAddress | read-only | current | This attribute identifies the IP address of the edge device established a VREP session. When VREP session is not in established state, this value is 0. The def… |
| 1.3.6.1.4.1.2011.6.187.11.1.20 | ColumnhwDocsQamNGODEdgeDeviceEstablishedLocalPort | read-only | current | This attribute identifies the TCP port number of the edge device established a VREP session. When VREP session is not in established state, this value is 0. Th… |
| 1.3.6.1.4.1.2011.6.187.11.1.21 | ColumnhwDocsQamNGODEdgeDeviceCost | read-create | current | This attribute identifies the cost of the edge devie. The cost attribute is a topology independent attribute. It represents the relative cost associated with t… |
| 1.3.6.1.4.1.2011.6.187.11.1.22 | ColumnhwDocsQamNGODEdgeDevicelocalIfType | read-write | current | Indicates the interface type. Options: 1. inloopback(1) -the system inner loopback interface 2. null(2) -the NULL interface 3. meth(3) -the ethernet interface … |
| 1.3.6.1.4.1.2011.6.187.11.1.23 | ColumnhwDocsQamNGODEdgeDevicelocalIfNumber | read-write | current | Indicates the interface number. Range: 0-4093 Range for the inloopback interface: 0 Range for the NULL interface: 0 Range for the MEth interface: 0 Range for t… |
| 1.3.6.1.4.1.2011.6.187.11.1.255 | ColumnhwDocsQamNGODEdgeDeviceRowStatus | read-create | current | Row status, used to query, create, modify, and delete a edge device. It supports the active(1), createAndGo(4), and destroy(6) operations. During query, the va… |
| 1.3.6.1.4.1.2011.6.187.12 | TablehwDocsQamNGODEdgeDeviceEdgeInputTable | not-accessible | current | Indicates the edge device input table. The index of this table is hwDocsQamNGODEdgeDeviceName and hwDocsQamNGODEdgeDeviceEdgeInputIndex. |
| 1.3.6.1.4.1.2011.6.187.12.1 | RowhwDocsQamNGODEdgeDeviceEdgeInputEntry | not-accessible | current | Indicates the edge device input table. The index of this entry is hwDocsQamNGODEdgeDeviceName and hwDocsQamNGODEdgeDeviceEdgeInputIndex. |
| 1.3.6.1.4.1.2011.6.187.12.1.1 | ColumnhwDocsQamNGODEdgeDeviceEdgeInputIndex | not-accessible | current | Indicates the index of the edge device input table. when set to 4294967295, the system automatically allocates an index for the instance. |
| 1.3.6.1.4.1.2011.6.187.12.1.2 | ColumnhwDocsQamNGODEdgeDeviceEdgeInputAddressType | read-create | current | This attribute identifies the IP address type of the edge device input host adress. |
| 1.3.6.1.4.1.2011.6.187.12.1.3 | ColumnhwDocsQamNGODEdgeDeviceEdgeInputAddress | read-create | current | This attribute identifies the IP address of the edge device input host adress. |
| 1.3.6.1.4.1.2011.6.187.12.1.4 | ColumnhwDocsQamNGODEdgeDeviceEdgeInputAddressMask | read-create | current | This attribute identifies the IP address mask of the edge device input host adress. |
| 1.3.6.1.4.1.2011.6.187.12.1.5 | ColumnhwDocsQamNGODEdgeDeviceEdgeInputIfindex | read-create | current | This attribute identifies the input ifindex of the edge device input port. The ifIndex is an ifType of docsCableMaclayer(127). |
| 1.3.6.1.4.1.2011.6.187.12.1.6 | ColumnhwDocsQamNGODEdgeDeviceEdgeInputMaxBandwidth | read-create | current | This attribute identifies the max bandwidth of the edge device input port. The default value is 0. Unit: kbps. |
| 1.3.6.1.4.1.2011.6.187.12.1.7 | ColumnhwDocsQamNGODEdgeDeviceEdgeInputGroupName | read-create | current | This attribute identifies the group name of the edge device input belongs to. The default value is null string. |
| 1.3.6.1.4.1.2011.6.187.12.1.255 | ColumnhwDocsQamNGODEdgeDeviceEdgeInputRowStatus | read-create | current | Row status, used to query, create, modify, and delete a edge device input. It supports the active(1), createAndGo(4), and destroy(6) operations. During query, … |
| 1.3.6.1.4.1.2011.6.187.13 | TablehwDocsQamNGODEdgeDeviceStatisticsTable | not-accessible | current | Indicates the edge device statistics table. The index of this table is hwDocsQamNGODEdgeDeviceName. |
| 1.3.6.1.4.1.2011.6.187.13.1 | RowhwDocsQamNGODEdgeDeviceStatisticsEntry | not-accessible | current | Indicates the edge device statistics table. The index of this entry is hwDocsQamNGODEdgeDeviceName. |
| 1.3.6.1.4.1.2011.6.187.13.1.1 | ColumnhwDocsQamNGODEdgeDeviceRecvOpenPkts | read-only | current | Indicates the number of OPEN packets received. |
| 1.3.6.1.4.1.2011.6.187.13.1.2 | ColumnhwDocsQamNGODEdgeDeviceSentOpenPkts | read-only | current | Indicates the number of OPEN packets sent. |
| 1.3.6.1.4.1.2011.6.187.13.1.3 | ColumnhwDocsQamNGODEdgeDeviceRecvKeepalivePkts | read-only | current | Indicates the number of KEEPALIVE packets received . |
| 1.3.6.1.4.1.2011.6.187.13.1.4 | ColumnhwDocsQamNGODEdgeDeviceSentKeepalivePkts | read-only | current | Indicates the number of KEEPALIVE packets sent. |
| 1.3.6.1.4.1.2011.6.187.13.1.5 | ColumnhwDocsQamNGODEdgeDeviceRecvNotificationPkts | read-only | current | Indicates the number of NOTIFICATION packets received . |
| 1.3.6.1.4.1.2011.6.187.13.1.6 | ColumnhwDocsQamNGODEdgeDeviceSentNotificationPkts | read-only | current | Indicates the number of NOTIFICATION packets sent. |
| 1.3.6.1.4.1.2011.6.187.13.1.7 | ColumnhwDocsQamNGODEdgeDeviceSentUpdatePkts | read-only | current | Indicates the number of UPDATE packets sent. |
| 1.3.6.1.4.1.2011.6.187.13.1.8 | ColumnhwDocsQamNGODEdgeDeviceRecvErrPkts | read-only | current | Indicates the number of ERROR packets received. |
| 1.3.6.1.4.1.2011.6.187.13.1.9 | ColumnhwDocsQamNGODEdgeDeviceRecvMsgHeaderErrPkts | read-only | current | Indicates the number of message header error packets received. |
| 1.3.6.1.4.1.2011.6.187.13.1.10 | ColumnhwDocsQamNGODEdgeDeviceRecvMsgHeaderBadLengthErrPkts | read-only | current | Indicates the number of message header bad length packets received. |
| 1.3.6.1.4.1.2011.6.187.13.1.11 | ColumnhwDocsQamNGODEdgeDeviceRecvMsgHeaderBadTypeErrPkts | read-only | current | Indicates the number of message header bad type packets received. |
| 1.3.6.1.4.1.2011.6.187.13.1.12 | ColumnhwDocsQamNGODEdgeDeviceRecvOpenMsgErrPkts | read-only | current | Indicates the number of OPEN message error packets received. |
| 1.3.6.1.4.1.2011.6.187.13.1.13 | ColumnhwDocsQamNGODEdgeDeviceRecvOpenMsgUnsupportedVersionErrPkts | read-only | current | Indicates the number of OPEN message unsupported versionError error packets received. |
| 1.3.6.1.4.1.2011.6.187.13.1.14 | ColumnhwDocsQamNGODEdgeDeviceRecvOpenMsgBadPeerAddressDomainErrPkts | read-only | current | Indicates the number of OPEN message bad peer address domain error packets received. |
| 1.3.6.1.4.1.2011.6.187.13.1.15 | ColumnhwDocsQamNGODEdgeDeviceRecvOpenMsgBadVREPIDErrPkts | read-only | current | Indicates the number of OPEN message VREPID error packets received. |
| 1.3.6.1.4.1.2011.6.187.13.1.16 | ColumnhwDocsQamNGODEdgeDeviceRecvOpenMsgUnsupportedOptionParaErrPkts | read-only | current | Indicates the number of OPEN message unsupported Option parameter error packets received. |
| 1.3.6.1.4.1.2011.6.187.13.1.17 | ColumnhwDocsQamNGODEdgeDeviceRecvOpenMsgUnacceptableHoldTimeErrPkts | read-only | current | Indicates the number of OPEN message unacceptable hold time error packets received. |
| 1.3.6.1.4.1.2011.6.187.13.1.18 | ColumnhwDocsQamNGODEdgeDeviceRecvOpenMsgUnsupportedCapabilityErrPkts | read-only | current | Indicates the number of OPEN message unsupported capability error packets received. |
| 1.3.6.1.4.1.2011.6.187.13.1.19 | ColumnhwDocsQamNGODEdgeDeviceRecvOpenMsgCapabilityMissmatchErrPkts | read-only | current | Indicates the number of OPEN message capability missmatch error packets received. |
| 1.3.6.1.4.1.2011.6.187.13.1.20 | ColumnhwDocsQamNGODEdgeDeviceStatisticsReset | read-write | current | Rest the statistics of edge device. Options: 1. clear(1) -indicates resetingthe statistics of edge device |
| 1.3.6.1.4.1.2011.6.187.13.1.21 | ColumnhwDocsQamNGODEdgeDeviceRecvNotificationErrPkts | read-only | current | Indicates the number of NOTIFICATION error packets received. |
| 1.3.6.1.4.1.2011.6.187.14 | TablehwDocsQamChannelTable | not-accessible | current | Indicates the qam channel table. The index of this table is ifindex. |
| 1.3.6.1.4.1.2011.6.187.14.1 | RowhwDocsQamChannelEntry | not-accessible | current | Indicates the qam channel table. The index of this entry is ifindex. |
| 1.3.6.1.4.1.2011.6.187.14.1.1 | ColumnhwDocsQamChannelStreamID | read-write | current | This attribute identifies the TSID of the EQAM channel. The default value is 4294967295. |
| 1.3.6.1.4.1.2011.6.187.14.1.2 | ColumnhwDocsQamChannelServiceGroupName | read-write | current | This attribute identifies the service group of the EQAM channel belongs to. Suggested format <RegionName>.<localname>. The default value is null string. |
| 1.3.6.1.4.1.2011.6.187.14.1.3 | ColumnhwDocsQamChannelEdgeDeviceName | read-write | current | This attribute identifies the egdge device of the EQAM channel belongs to. The default value is null string. |
| 1.3.6.1.4.1.2011.6.187.15 | TablehwDocsQamVideoStreamMPTSProgramTable | not-accessible | current | Indicates the dynamic program information table for mpts video stream. The indexes of this table are ifIndex, hwDocsQamVideoStreamIndex and hwDocsQamVideoStrea… |
| 1.3.6.1.4.1.2011.6.187.15.1 | RowhwDocsQamVideoStreamMPTSProgramEntry | not-accessible | current | Indicates the dynamic program information table for mpts video stream. The indexes of this entry are ifIndex, hwDocsQamVideoStreamIndex and hwDocsQamVideoStrea… |
| 1.3.6.1.4.1.2011.6.187.15.1.1 | ColumnhwDocsQamVideoStreamMPTSProgramIndex | not-accessible | current | Indicates the program index of a MPTS video stream. |
| 1.3.6.1.4.1.2011.6.187.15.1.2 | ColumnhwDocsQamVideoStreamMPTSInputProgram | read-only | current | Indicates the input program ID, the value -1 indicates that the input program ID is invalid. |
| 1.3.6.1.4.1.2011.6.187.15.1.3 | ColumnhwDocsQamVideoStreamMPTSInputPMTPID | read-only | current | Indicates the input PMT PID, the value -1 indicates that the input PMT PID is invalid. |
| 1.3.6.1.4.1.2011.6.187.15.1.4 | ColumnhwDocsQamVideoStreamMPTSInputPCRPID | read-only | current | Indicates the input PCR PID, the value -1 indicates that the input PCR PID is invalid. |
| 1.3.6.1.4.1.2011.6.187.15.1.5 | ColumnhwDocsQamVideoStreamMPTSOutputProgram | read-only | current | Indicates the program ID of the output stream, the value -1 indicates that the program ID of the output stream is invalid. |
| 1.3.6.1.4.1.2011.6.187.15.1.6 | ColumnhwDocsQamVideoStreamMPTSOutputPMTPID | read-only | current | Indicates the PMT PID of the output stream, the value -1 indicates that the PMT PID of the output stream is invalid. |
| 1.3.6.1.4.1.2011.6.187.15.1.7 | ColumnhwDocsQamVideoStreamMPTSOutputPCRPID | read-only | current | Indicates the PCR PID of the output stream, the value -1 indicates that the PCR PID of the output stream is invalid. |
| 1.3.6.1.4.1.2011.6.187.15.1.8 | ColumnhwDocsQamVideoStreamMPTSInputESPIDList | read-only | current | Indicates the ESPID list for input MPTS streams. PID consists of two bytes and must be in one-to-one mapping with ESTypeList. |
| 1.3.6.1.4.1.2011.6.187.15.1.9 | ColumnhwDocsQamVideoStreamMPTSOutputESPIDList | read-only | current | Indicates the ESPID list for output MPTS streams. PID consists of two bytes and must be in one-to-one mapping with ESTypeList. |
| 1.3.6.1.4.1.2011.6.187.15.1.10 | ColumnhwDocsQamVideoStreamMPTSESTypeList | read-only | current | Indicate the ES type list. One byte indicates a type, which must be in one-to-one mapping with the ESPID list for input or output streams. |
| 1.3.6.1.4.1.2011.6.187.16 | TablehwDocsQamInputTSTable | not-accessible | current | Indicates the input TS table. The index of this table is hwDocsQamInputTSIndex. |
| 1.3.6.1.4.1.2011.6.187.16.1 | RowhwDocsQamInputTSEntry | not-accessible | current | Indicates the input TS table. The index of this entry is hwDocsQamInputTSIndex. |
| 1.3.6.1.4.1.2011.6.187.16.1.1 | ColumnhwDocsQamInputTSIndex | accessible-for-notify | current | Indicates the index of a input TS. You can also fill 4294967295 and the system will automatically allocate an index. |
| 1.3.6.1.4.1.2011.6.187.16.1.2 | ColumnhwDocsQamInputTSIpAddressType | read-create | current | Indicates the address type of the multicast IP address in input TS. Only IPv4 addresses are supported. |
| 1.3.6.1.4.1.2011.6.187.16.1.3 | ColumnhwDocsQamInputTSMulticastIpAddress | read-create | current | Indicates the multicast IP address of the input TS. |
| 1.3.6.1.4.1.2011.6.187.16.1.4 | ColumnhwDocsQamInputTSSourceIpAddress | read-create | current | Indicates the source IP address of the input TS. |
| 1.3.6.1.4.1.2011.6.187.16.1.5 | ColumnhwDocsQamInputTSSecondaryMulticastIpAddress | read-create | current | Indicates the secondary multicast IP address of the input TS. |
| 1.3.6.1.4.1.2011.6.187.16.1.6 | ColumnhwDocsQamInputTSSecondarySourceIpAddress | read-create | current | Indicates the secondary source IP address of the input TS. |
| 1.3.6.1.4.1.2011.6.187.16.1.7 | ColumnhwDocsQamInputTSState | read-only | current | Indicates the state of input TS. Options: 1. offline(1) -indicates the offline state 2. online(2) -indicates the online state 3. unknown(3) -indicates the unkn… |
| 1.3.6.1.4.1.2011.6.187.16.1.8 | ColumnhwDocsQamInputTSTraffic | read-only | current | Indicates the traffic of input TS. Default: 0 |
| 1.3.6.1.4.1.2011.6.187.16.1.9 | ColumnhwDocsQamInputTSDiscontinuityCounter | read-only | current | Indicates the discontinuity counter of input TS. Default: 0 |
| 1.3.6.1.4.1.2011.6.187.16.1.10 | ColumnhwDocsQamInputTSEPGInput | read-create | current | Indicates whether the transport stream is treated as the EPG input. The default value is false. |
| 1.3.6.1.4.1.2011.6.187.16.1.11 | ColumnhwDocsQamInputTSJitter | read-create | current | Indicates the network jitter allowed. The default value is 100. 0 indicatdes network jitter is not allowed. |
| 1.3.6.1.4.1.2011.6.187.16.1.12 | ColumnhwDocsQamInputTSRTPSequenceErrorCounter | read-only | current | Indicates the RTP sequence error counter of input TS. |
| 1.3.6.1.4.1.2011.6.187.16.1.13 | ColumnhwDocsQamInputTSRedundancyMode | read-create | current | Indicates the redundancy mode of input TS. Options: 1. backup(1) -Indicates the redundancy mode in which one TS is selected from two input TSs. When the second… |
| 1.3.6.1.4.1.2011.6.187.16.1.14 | ColumnhwDocsQamInputTSUdpPort | read-create | current | Indicates the UDP port number of the input TS. The default value is 0, indicating that the UDP port number is invalid. Range: 0-65535 |
| 1.3.6.1.4.1.2011.6.187.16.1.15 | ColumnhwDocsQamInputTSSecondaryUdpPort | read-create | current | Indicates the secondary UDP port number of the input TS. The default value is 0, indicating that the UDP port number is invalid. Range: 0-65535 |
| 1.3.6.1.4.1.2011.6.187.16.1.16 | ColumnhwDocsQamInputTSMode | read-create | current | Indicates the PSI parsing mode of an input TS.The default value is dvb(1). Options: 1. dvb(1) - The PSI parsing mode is dvb. 2. mpeg(2)- The PSI parsing mode i… |
| 1.3.6.1.4.1.2011.6.187.16.1.17 | ColumnhwDocsQamInputTSTransportStreamID | read-only | current | Indicates the transport stream id of an input TS .The default value is 4294967295, which indicates that stream id is not learned. |
| 1.3.6.1.4.1.2011.6.187.16.1.18 | ColumnhwDocsQamInputTSRedundancyTriggers | read-create | current | Indicates the trigger conditions for protection switching on input TSs. The format is 4 bits. The default value is 0, indicates that there is no trigger condit… |
| 1.3.6.1.4.1.2011.6.187.16.1.19 | ColumnhwDocsQamInputTSRedundancyTriggersDefault | read-create | current | Indicates whether the default trigger condition is used for protection switching. The default value is true, indicates that the trigger condition of hwDocsQamI… |
| 1.3.6.1.4.1.2011.6.187.16.1.255 | ColumnhwDocsQamInputTSRowStatus | read-create | current | Row status, used to query, create, modify, and delete a input TS table. It supports the active(1), createAndGo(4), and destroy(6) operations. During query, the… |
| 1.3.6.1.4.1.2011.6.187.17 | TablehwDocsQamDVBDomainTable | not-accessible | current | Indicates the DVB video domain table used to manage information, such as EQAM's profile name. The index of this table is hwDocsQamDVBDomainName. |
| 1.3.6.1.4.1.2011.6.187.17.1 | RowhwDocsQamDVBDomainEntry | not-accessible | current | Indicates the DVB video domain table used to manage information, such as EQAM's profile name. The index of this entry is hwDocsQamDVBDomainName. |
| 1.3.6.1.4.1.2011.6.187.17.1.1 | ColumnhwDocsQamDVBDomainName | not-accessible | current | Indicates the DVB video domain name. |
| 1.3.6.1.4.1.2011.6.187.17.1.2 | ColumnhwDocsQamDVBDomainBindVideoProfile | read-create | current | Indicates the bind video profile name. |
| 1.3.6.1.4.1.2011.6.187.17.1.3 | ColumnhwDocsQamDVBDomainRowStatus | read-create | current | Row status, used to query, create, and delete a DVB domain table. It supports the active(1), createAndGo(4), and destroy(6) operations. During query, the value… |
| 1.3.6.1.4.1.2011.6.187.17.1.4 | ColumnhwDocsQamDVBDomainPSISIDefModeSDTA | read-create | current | Indicates the output policy of SDT(Service Information Table) actual. The default value is stop(1). |
| 1.3.6.1.4.1.2011.6.187.17.1.5 | ColumnhwDocsQamDVBDomainPSISIDefModeSDTO | read-create | current | Indicates the output policy of SDT(Service Information Table) other. The default value is stop(1). |
| 1.3.6.1.4.1.2011.6.187.17.1.6 | ColumnhwDocsQamDVBDomainPSISIDefModeEITpfA | read-create | current | Indicates the output policy of actual TS, present/following EIT(Event Information Table). The default value is stop(1). |
| 1.3.6.1.4.1.2011.6.187.17.1.7 | ColumnhwDocsQamDVBDomainPSISIDefModeEITpfO | read-create | current | Indicates the output policy of other TS, present/following EIT(Event Information Table). The default value is stop(1). |
| 1.3.6.1.4.1.2011.6.187.17.1.8 | ColumnhwDocsQamDVBDomainPSISIDefModeEITsFirstA | read-create | current | Indicates the output policy of actual TS, first(day 0-3) schedual EIT(Event Information Table). The default value is stop(1). |
| 1.3.6.1.4.1.2011.6.187.17.1.9 | ColumnhwDocsQamDVBDomainPSISIDefModeEITsFirstO | read-create | current | Indicates the output policy of other TS, first(day 0-3) schedual EIT(Event Information Table). The default value is stop(1). |
| 1.3.6.1.4.1.2011.6.187.17.1.10 | ColumnhwDocsQamDVBDomainPSISIDefModeEITsSecondA | read-create | current | Indicates the output policy of actual TS, second(day 4-7) schedual EIT(Event Information Table). The default value is stop(1). |
| 1.3.6.1.4.1.2011.6.187.17.1.11 | ColumnhwDocsQamDVBDomainPSISIDefModeEITsSecondO | read-create | current | Indicates the output policy of other TS, second(day 4-7) schedual EIT(Event Information Table). The default value is stop(1). |
| 1.3.6.1.4.1.2011.6.187.17.1.12 | ColumnhwDocsQamDVBDomainPSISIDefIntervalPAT | read-create | current | Indicates the playout interval of PAT(Program Association Table). Default: 100 |
| 1.3.6.1.4.1.2011.6.187.17.1.13 | ColumnhwDocsQamDVBDomainPSISIDefIntervalPMT | read-create | current | Indicates the playout interval of PMT(Program Map Table). Default: 100 |
| 1.3.6.1.4.1.2011.6.187.17.1.14 | ColumnhwDocsQamDVBDomainPSISIDefIntervalSDTA | read-create | current | Indicates the playout interval of SDT(Service Information Table) actual. Default: 1000 |
| 1.3.6.1.4.1.2011.6.187.17.1.15 | ColumnhwDocsQamDVBDomainPSISIDefIntervalSDTO | read-create | current | Indicates the playout interval of SDT(Service Information Table) other. Default: 2000 |
| 1.3.6.1.4.1.2011.6.187.17.1.16 | ColumnhwDocsQamDVBDomainPSISIDefIntervalEITpfA | read-create | current | Indicates the playout interval of actual TS, present/following EIT(Event Information Table). Default: 5000 |
| 1.3.6.1.4.1.2011.6.187.17.1.17 | ColumnhwDocsQamDVBDomainPSISIDefIntervalEITpfO | read-create | current | Indicates the playout interval of other TS, present/following EIT(Event Information Table). Default: 20000 |
| 1.3.6.1.4.1.2011.6.187.17.1.18 | ColumnhwDocsQamDVBDomainPSISIDefIntervalEITsFirstA | read-create | current | Indicates the playout interval of actual TS, first(day 0-3) schedual EIT(Event Information Table). Default: 60000 |
| 1.3.6.1.4.1.2011.6.187.17.1.19 | ColumnhwDocsQamDVBDomainPSISIDefIntervalEITsFirstO | read-create | current | Indicates the playout interval of other TS, first(day 0-3) schedual EIT(Event Information Table). Default: 600000 |
| 1.3.6.1.4.1.2011.6.187.17.1.20 | ColumnhwDocsQamDVBDomainPSISIDefIntervalEITsSecondA | read-create | current | Indicates the playout interval of actual TS, second(day 4-7) schedual EIT(Event Information Table). Default: 600000 |
| 1.3.6.1.4.1.2011.6.187.17.1.21 | ColumnhwDocsQamDVBDomainPSISIDefIntervalEITsSecondO | read-create | current | Indicates the playout interval of other TS, second(day 4-7) schedual EIT(Event Information Table). Default: 1800000 |
| 1.3.6.1.4.1.2011.6.187.17.1.22 | ColumnhwDocsQamDVBDomainPSISIDefSpeedEIT | read-create | current | Indicates the output speed of EIT(Event Information Table). Default: 1000 |
| 1.3.6.1.4.1.2011.6.187.17.1.23 | ColumnhwDocsQamDVBDomainDefChannelOutputRate | read-create | current | Indicates the default output rate of the channel in the DVB domain. Default: 38015 |
| 1.3.6.1.4.1.2011.6.187.18 | TablehwDocsQamVODPortConfigTable | not-accessible | current | Indicates the VOD domain port table used to manage relationships between VOD domains and ports. The index of this table is ifIndex. |
| 1.3.6.1.4.1.2011.6.187.18.1 | RowhwDocsQamVODPortConfigEntry | not-accessible | current | Indicates the VOD domain port table used to manage relationships between VOD domains and ports. The index of this entry is ifIndex. |
| 1.3.6.1.4.1.2011.6.187.18.1.1 | ColumnhwDocsQamVODPortConfigDomainName | read-create | current | Indicates the VOD domain name. |
| 1.3.6.1.4.1.2011.6.187.18.1.2 | ColumnhwDocsQamVODPortConfigStartUDPPort | read-create | current | Indicates the start udp value of port. |
| 1.3.6.1.4.1.2011.6.187.18.1.3 | ColumnhwDocsQamVODPortConfigRowStatus | read-create | current | Row status, used to query, create, modify, and delete a port table. It supports the active(1), createAndGo(4), and destroy(6) operations. During query, the val… |
| 1.3.6.1.4.1.2011.6.187.19 | TablehwDocsQamDVBPortConfigTable | not-accessible | current | Indicates the DVB domain port table used to manage relationships between DVB domains and ports. The index of this table is ifIndex. |
| 1.3.6.1.4.1.2011.6.187.19.1 | RowhwDocsQamDVBPortConfigEntry | not-accessible | current | Indicates the DVB domain port table used to manage relationships between DVB domains and ports. The index of this entry is ifIndex. |
| 1.3.6.1.4.1.2011.6.187.19.1.1 | ColumnhwDocsQamDVBPortConfigDomainName | read-create | current | Indicates the DVB domain name. |
| 1.3.6.1.4.1.2011.6.187.19.1.2 | ColumnhwDocsQamDVBPortConfigRowStatus | read-create | current | Row status, used to query, create, modify, and delete a port table. It supports the active(1), createAndGo(4), and destroy(6) operations. During query, the val… |
| 1.3.6.1.4.1.2011.6.187.20 | TablehwDocsQamInputTSStateTable | not-accessible | current | Indicates the EQAM TS state. The index of this table is hwDocsQamInputTSIndex. |
| 1.3.6.1.4.1.2011.6.187.20.1 | RowhwDocsQamInputTSStateEntry | not-accessible | current | Indicates the EQAM TS state. The index of this entry is hwDocsQamInputTSIndex. |
| 1.3.6.1.4.1.2011.6.187.20.1.1 | ColumnhwDocsQamInputTSStateSwitchOver | read-create | current | Indicates the opeartion for swiching over, the default value is none(255). Options: 1. switchover(1) -switch over the input TS. 2. none(255) -no operation. |
| 1.3.6.1.4.1.2011.6.187.20.1.2 | ColumnhwDocsQamInputTSStateActive | read-only | current | Indicates the active state of input TS. Options: 1. primary(1) -indicates the active state of the input TS is primary. 2. secondary(2) -indicates the active st… |
| 1.3.6.1.4.1.2011.6.187.20.1.3 | ColumnhwDocsQamInputTSStateSwitchoverReason | read-only | current | Indicates the protection switching cause, the default value is none(255). Options: 1. manual(1) -indicates the protection switching cause is manual switching. … |
| 1.3.6.1.4.1.2011.6.187.21 | TablehwDocsQamInputTSProgramTable | not-accessible | current | Indicates the program information of input TS. The indexes of this table are hwDocsQamInputTSIndex and hwDocsQamInputTSProgramIndex. |
| 1.3.6.1.4.1.2011.6.187.21.1 | RowhwDocsQamInputTSProgramEntry | not-accessible | current | Indicates the program information of input TS. The indexes of this entry are hwDocsQamInputTSIndex and hwDocsQamInputTSProgramIndex. |
| 1.3.6.1.4.1.2011.6.187.21.1.1 | ColumnhwDocsQamInputTSProgramIndex | not-accessible | current | Indicates the index of a program in input TS. |
| 1.3.6.1.4.1.2011.6.187.21.1.2 | ColumnhwDocsQamInputTSProgramID | read-only | current | Indicates the program ID , the value -1 indicates that the program ID is invalid. |
| 1.3.6.1.4.1.2011.6.187.21.1.3 | ColumnhwDocsQamInputTSProgramPMTPID | read-only | current | Indicates the PMT PID, the value -1 indicates that the PMT PID is invalid. |
| 1.3.6.1.4.1.2011.6.187.21.1.4 | ColumnhwDocsQamInputTSProgramPCRPID | read-only | current | Indicates the PCR PID, the value -1 indicates that the PCR PID is invalid. |
| 1.3.6.1.4.1.2011.6.187.21.1.5 | ColumnhwDocsQamInputTSProgramESPIDList | read-only | current | Indicates the ESPID list. PID consists of two bytes and must be in one-to-one mapping with ESTypeList. |
| 1.3.6.1.4.1.2011.6.187.21.1.6 | ColumnhwDocsQamInputTSProgramESTypeList | read-only | current | Indicate the ES type list. One byte indicates a type, which must be in one-to-one mapping with the ESPID list for program. |
| 1.3.6.1.4.1.2011.6.187.21.1.7 | ColumnhwDocsQamInputTSProgramDiscontinuityCounter | read-only | current | Indicates the discontinuity counter of program. Default: 0 |
| 1.3.6.1.4.1.2011.6.187.21.1.8 | ColumnhwDocsQamInputTSProgramName | read-only | current | Indicates the program name in input TS. |
| 1.3.6.1.4.1.2011.6.187.21.1.9 | ColumnhwDocsQamInputTSProgramState | read-only | current | Indicates the program state in input TS. Options: 1. offline(1) -indicates the offline state 2. online(2) -indicates the online state 3. unknown(3) -indicates … |
| 1.3.6.1.4.1.2011.6.187.21.1.10 | ColumnhwDocsQamInputTSProgramRate | read-only | current | Indicates the rate of program in input TS. Unit: kbit/s. The default value is 0. |
| 1.3.6.1.4.1.2011.6.187.21.1.11 | ColumnhwDocsQamInputTSProgramMaxRate | read-only | current | Indicates the maximum rate of program in input TS. Unit: kbit/s. The default value is 0. |
| 1.3.6.1.4.1.2011.6.187.21.1.12 | ColumnhwDocsQamInputTSProgramMinRate | read-only | current | Indicates the minimum rate of program in input TS. Unit: kbit/s. The default value is 0. |
| 1.3.6.1.4.1.2011.6.187.21.1.13 | ColumnhwDocsQamInputTSProgramCaNumber | read-only | current | Indicates the CA number of program in input TS. |
| 1.3.6.1.4.1.2011.6.187.21.1.14 | ColumnhwDocsQamInputTSProgramCaPIDList | read-only | current | Indicates the CA PID list of an input program. A PID is displayed as a 2-byte string in network order. A maximum of 4 CAs are supported. The default value is n… |
| 1.3.6.1.4.1.2011.6.187.21.1.15 | ColumnhwDocsQamInputTSProgramCaSystemIDList | read-only | current | Indicates the CA system ID list of an input program. A CA system ID is displayed as a 2-byte string in network order. A maximum of 4 CAs are supported. The def… |
| 1.3.6.1.4.1.2011.6.187.22 | TablehwDocsQamOutputTSProgramTable | not-accessible | current | Indicates the program information of output TS. The indexes of this table are ifIndex and hwDocsQamOutputTSProgramIndex. |
| 1.3.6.1.4.1.2011.6.187.22.1 | RowhwDocsQamOutputTSProgramEntry | not-accessible | current | Indicates the program information of output TS. The indexes of this entry are ifIndex and hwDocsQamOutputTSProgramIndex. |
| 1.3.6.1.4.1.2011.6.187.22.1.1 | ColumnhwDocsQamOutputTSProgramIndex | not-accessible | current | Indicates the index of a program in output TS. |
| 1.3.6.1.4.1.2011.6.187.22.1.2 | ColumnhwDocsQamOutputTSProgramID | read-only | current | Indicates the program ID , the value -1 indicates that the program ID is invalid. |
| 1.3.6.1.4.1.2011.6.187.22.1.3 | ColumnhwDocsQamOutputTSProgramPMTPID | read-only | current | Indicates the PMT PID, the value -1 indicates that the PMT PID is invalid. |
| 1.3.6.1.4.1.2011.6.187.22.1.4 | ColumnhwDocsQamOutputTSProgramPCRPID | read-only | current | Indicates the PCR PID, the value -1 indicates that the PCR PID is invalid. |
| 1.3.6.1.4.1.2011.6.187.22.1.5 | ColumnhwDocsQamOutputTSProgramESPIDList | read-only | current | Indicates the ESPID list. PID consists of two bytes and must be in one-to-one mapping with ESTypeList. |
| 1.3.6.1.4.1.2011.6.187.22.1.6 | ColumnhwDocsQamOutputTSProgramESTypeList | read-only | current | Indicate the ES type list. One byte indicates a type, which must be in one-to-one mapping with the ESPID list for program. |
| 1.3.6.1.4.1.2011.6.187.22.1.7 | ColumnhwDocsQamOutputTSProgramName | read-only | current | Indicate the program name in output TS. |
| 1.3.6.1.4.1.2011.6.187.22.1.8 | ColumnhwDocsQamOutputTSProgramState | read-only | current | Indicate the state of program in output TS. Options: 1. offline(1) -indicates the offline state 2. online(2) -indicates the online state 3. unknown(3) -indicat… |
| 1.3.6.1.4.1.2011.6.187.22.1.9 | ColumnhwDocsQamOutputTSProgramRate | read-only | current | Indicate the rate of program in output TS. Unit: kbit/s. The default value is 0. |
| 1.3.6.1.4.1.2011.6.187.22.1.10 | ColumnhwDocsQamOutputTSProgramMaxRate | read-only | current | Indicate the maximum rate of program in output TS. Unit: kbit/s. The default value is 0. |
| 1.3.6.1.4.1.2011.6.187.22.1.11 | ColumnhwDocsQamOutputTSProgramMinRate | read-only | current | Indicate the minimum rate of program in output TS. Unit: kbit/s. The default value is 0. |
| 1.3.6.1.4.1.2011.6.187.22.1.12 | ColumnhwDocsQamOutputTSProgramCaNumber | read-only | current | Indicate the CA number of program in output TS. |
| 1.3.6.1.4.1.2011.6.187.22.1.13 | ColumnhwDocsQamOutputTSProgramCaPIDList | read-only | current | Indicates the CA PID list of an output program. A PID is displayed as a 2-byte string in network order. A maximum of 4 CAs are supported. |
| 1.3.6.1.4.1.2011.6.187.22.1.14 | ColumnhwDocsQamOutputTSProgramCaSystemIDList | read-only | current | Indicates the CA system ID list of an output program. A CA system ID is displayed as a 2-byte string in network order. A maximum of 4 CAs are supported. |
| 1.3.6.1.4.1.2011.6.187.23 | TablehwDocsQamDVBInputTSStatisticsTable | not-accessible | current | Indicates the statistics table for input TS. The indexes of this table is hwDocsQamDVBInputTSStatisticsIndex. |
| 1.3.6.1.4.1.2011.6.187.23.1 | RowhwDocsQamDVBInputTSStatisticsEntry | not-accessible | current | Indicates the statistics table for input TS. The index of this entry is hwDocsQamDVBInputTSStatisticsIndex. |
| 1.3.6.1.4.1.2011.6.187.23.1.1 | ColumnhwDocsQamDVBInputTSStatisticsIndex | not-accessible | current | Indicates the index of statistics table for input TS. |
| 1.3.6.1.4.1.2011.6.187.23.1.2 | ColumnhwDocsQamDVBInputTSStatisticsOperMode | read-write | current | Indicates the operation mode. The set operation can clear statistics for input TS. Options: 1. clearStatistic(1) -indicates clearing statistics for input TS 2.… |
| 1.3.6.1.4.1.2011.6.187.23.1.3 | ColumnhwDocsQamDVBInputTSPackets | read-only | current | Indicates packet statistics for input TS. |
| 1.3.6.1.4.1.2011.6.187.23.1.4 | ColumnhwDocsQamDVBInputTSCountOfJitterOverflow | read-only | current | Indicates the jitter overflow statistics. |
| 1.3.6.1.4.1.2011.6.187.23.1.5 | ColumnhwDocsQamDVBInputTSCountOfJitterUnderflow | read-only | current | Indicates the jitter underflow statistics. |
| 1.3.6.1.4.1.2011.6.187.23.1.6 | ColumnhwDocsQamDVBInputTSDiscontinuityCounter | read-only | current | Indicates the discontinuity counter of input TS. |
| 1.3.6.1.4.1.2011.6.187.23.1.7 | ColumnhwDocsQamDVBInputTSRTPSequenceErrorCounter | read-only | current | Indicates the RTP sequence error counter of input TS. |
| 1.3.6.1.4.1.2011.6.187.23.1.8 | ColumnhwDocsQamDVBInputTSPATErrors | read-only | current | Indicates the number of program association table (PAT) errors of the input transport stream (TS). |
| 1.3.6.1.4.1.2011.6.187.23.1.9 | ColumnhwDocsQamDVBInputTSPATMissings | read-only | current | Indicates the number of lost PATs of the input TS. |
| 1.3.6.1.4.1.2011.6.187.23.1.10 | ColumnhwDocsQamDVBInputTSPMTErrors | read-only | current | Indicates the number of program map table (PMT) errors of the input TS. |
| 1.3.6.1.4.1.2011.6.187.23.1.11 | ColumnhwDocsQamDVBInputTSPMTMissings | read-only | current | Indicates the number of lost PMTs of the input TS. |
| 1.3.6.1.4.1.2011.6.187.23.1.12 | ColumnhwDocsQamDVBInputTSOriginalPrimaryRTPSequenceErrorCounter | read-only | current | Indicates the primary original RTP error count of the input TS. |
| 1.3.6.1.4.1.2011.6.187.23.1.13 | ColumnhwDocsQamDVBInputTSOriginalSecondaryRTPSequenceErrorCounter | read-only | current | Indicates the secondary original RTP error count of the input TS. |
| 1.3.6.1.4.1.2011.6.187.23.1.14 | ColumnhwDocsQamDVBInputTSSeamlessAverageDelay | read-only | current | Indicates the average delay of the input TS in seamless mode. The default value is 4294967295, indicates that no delay is detected. |
| 1.3.6.1.4.1.2011.6.187.23.1.15 | ColumnhwDocsQamDVBInputTSSeamlessMaxDelay | read-only | current | Indicates the maximum delay of the input TS in seamless mode. The default value is 4294967295, indicates that no delay is detected. |
| 1.3.6.1.4.1.2011.6.187.23.1.16 | ColumnhwDocsQamDVBInputTSSeamlessMinDelay | read-only | current | Indicates the minimum delay of the input TS in seamless mode. The default value is 4294967295, indicates that no delay is detected. |
| 1.3.6.1.4.1.2011.6.187.23.1.17 | ColumnhwDocsQamInputTSStatisticsLastCleared | read-only | current | Indicates the time on which input TS statistics are cleared the last time. The default value is 1970-01-01 00:00:00, indicates input TS statistics has never be… |
| 1.3.6.1.4.1.2011.6.187.24 | NodehwDocsQamNotificationObject | |||
| 1.3.6.1.4.1.2011.6.187.24.1 | ScalarhwDocsQamNotificationProgramID | accessible-for-notify | current | Program ID. |
| 1.3.6.1.4.1.2011.6.187.24.2 | ScalarhwDocsQamNotificationPID | accessible-for-notify | current | PID. |
| 1.3.6.1.4.1.2011.6.187.25 | NotificationhwDocsQamDVBPATErrorTrap | current | The hwDocsQamDVBPATErrorEvent will be sent when the content of input PAT is incorrect. | |
| 1.3.6.1.4.1.2011.6.187.26 | NotificationhwDocsQamDVBPATMissingTrap | current | The hwDocsQamDVBPATMissingEvent will be sent when PAT is missing. | |
| 1.3.6.1.4.1.2011.6.187.27 | NotificationhwDocsQamDVBPMTErrorTrap | current | The hwDocsQamDVBPMTErrorEvent will be sent when the content of input PMT is incorrect. | |
| 1.3.6.1.4.1.2011.6.187.28 | NotificationhwDocsQamDVBPMTMissingTrap | current | The hwDocsQamDVBPMTMissingEvent will be sent when PMT is missing. | |
| 1.3.6.1.4.1.2011.6.187.29 | NotificationhwDocsQamDVBContinutyCounterErrorTrap | current | The hwDocsQamDVBContinutyCounterErrorEvent will be sent when the continuity counter error rate is too high. | |
| 1.3.6.1.4.1.2011.6.187.30 | TablehwDocsQamDVBDomainChannelTable | not-accessible | current | Indicates the DVB domain channel table used to configure the networkid, streamid and output policy of channels in a DVB domain. The indexes of this table are h… |
| 1.3.6.1.4.1.2011.6.187.30.1 | RowhwDocsQamDVBDomainChannelEntry | not-accessible | current | Indicates the DVB domain channel table used to configure the networkid, streamid and output policy of channels in a DVB domain. The indexes of this entry are h… |
| 1.3.6.1.4.1.2011.6.187.30.1.1 | ColumnhwDocsQamDVBDomainChannelID | not-accessible | current | Indicates the channel ID. |
| 1.3.6.1.4.1.2011.6.187.30.1.2 | ColumnhwDocsQamDVBDomainChannelNetworkID | read-write | current | Indicates the network id of the channel. The default value is 4294967295, indicating the network id of the channel is invalid. |
| 1.3.6.1.4.1.2011.6.187.30.1.3 | ColumnhwDocsQamDVBDomainChannelTransportStreamID | read-write | current | Indicates the transport stream id of the channel. The default value is 4294967295, indicating the stream id of the channel is invalid. |
| 1.3.6.1.4.1.2011.6.187.30.1.4 | ColumnhwDocsQamDVBDomainChannelPSISIModeSDTA | read-write | current | Indicates the output policy of SDT(Service Information Table) actual. The default value is default(3). |
| 1.3.6.1.4.1.2011.6.187.30.1.5 | ColumnhwDocsQamDVBDomainChannelPSISIModeSDTO | read-write | current | Indicates the output policy of SDT(Service Information Table) other. The default value is default(3). |
| 1.3.6.1.4.1.2011.6.187.30.1.6 | ColumnhwDocsQamDVBDomainChannelPSISIModeEITpfA | read-write | current | Indicates the output policy of actual TS, present/following EIT(Event Information Table). The default value is default(3). |
| 1.3.6.1.4.1.2011.6.187.30.1.7 | ColumnhwDocsQamDVBDomainChannelPSISIModeEITpfO | read-write | current | Indicates the output policy of other TS, present/following EIT(Event Information Table). The default value is default(3). |
| 1.3.6.1.4.1.2011.6.187.30.1.8 | ColumnhwDocsQamDVBDomainChannelPSISIModeEITsFirstA | read-write | current | Indicates the output policy of actual TS, first(day 0-3) schedual EIT(Event Information Table). The default value is default(3). |
| 1.3.6.1.4.1.2011.6.187.30.1.9 | ColumnhwDocsQamDVBDomainChannelPSISIModeEITsFirstO | read-write | current | Indicates the output policy of other TS, first(day 0-3) schedual EIT(Event Information Table). The default value is default(3). |
| 1.3.6.1.4.1.2011.6.187.30.1.10 | ColumnhwDocsQamDVBDomainChannelPSISIModeEITsSecondA | read-write | current | Indicates the output policy of actual TS, second(day 4-7) schedual EIT(Event Information Table). The default value is default(3). |
| 1.3.6.1.4.1.2011.6.187.30.1.11 | ColumnhwDocsQamDVBDomainChannelPSISIModeEITsSecondO | read-write | current | Indicates the output policy of other TS, second(day 4-7) schedual EIT(Event Information Table). The default value is default(3). |
| 1.3.6.1.4.1.2011.6.187.30.1.12 | ColumnhwDocsQamDVBDomainChannelOriginalNetworkID | read-write | current | Indicates the original network ID of a DVB channel. The default value is 4294967295, which indicates that no original network ID is configured. When no origina… |
| 1.3.6.1.4.1.2011.6.187.30.1.13 | ColumnhwDocsQamDVBDomainChannelOutputRate | read-write | current | Indicates the output rate of the channel in the DVB domain. The default value is 4294967295, which indicates that no output rate of the channel is configured. … |
| 1.3.6.1.4.1.2011.6.187.30.1.14 | ColumnhwDocsQamDVBDomainChannelOutputEnable | read-create | current | Indicates the status of the channel in the DVB domain. The default value is true. |
| 1.3.6.1.4.1.2011.6.187.31 | TablehwDocsQamFMDomainTable | not-accessible | current | Indicates the FM domain table used to create or destroy a FM domain. The index of this table is hwDocsQamFMDomainName. |
| 1.3.6.1.4.1.2011.6.187.31.1 | RowhwDocsQamFMDomainEntry | not-accessible | current | Indicates the FM domain table used to create or destroy a FM domain. The index of this entry is hwDocsQamFMDomainName. |
| 1.3.6.1.4.1.2011.6.187.31.1.1 | ColumnhwDocsQamFMDomainName | not-accessible | current | Indicates the FM domain name. |
| 1.3.6.1.4.1.2011.6.187.31.1.2 | ColumnhwDocsQamFMDomainMapNumber | read-only | current | Indicates the number of FM mapping in the FM domain. |
| 1.3.6.1.4.1.2011.6.187.31.1.3 | ColumnhwDocsQamFMDomainPortNumber | read-only | current | Indicates the number of ports added in the FM domain. |
| 1.3.6.1.4.1.2011.6.187.31.1.4 | ColumnhwDocsQamFMDomainRowStatus | read-create | current | Row status, used to query, create, and delete a FM domain table. It supports the active(1), createAndGo(4) and destroy(6) operations. During query, the value o… |
| 1.3.6.1.4.1.2011.6.187.32 | TablehwDocsQamFmMapTable | not-accessible | current | Indicates the FM mapping table used to configure the mapping between video streams and cable channels. The indexes of this table are hwDocsQamFMDomainName and … |
| 1.3.6.1.4.1.2011.6.187.32.1 | RowhwDocsQamFmMapEntry | not-accessible | current | Indicates the FM mapping table used to configure the mapping between video streams and cable channels. The indexes of this entry are hwDocsQamFMDomainName and … |
| 1.3.6.1.4.1.2011.6.187.32.1.1 | ColumnhwDocsQamFmMapIndex | not-accessible | current | Indicates the index of a FM mapping table. You can also fill 4294967295 and the system will automatically allocate an index. |
| 1.3.6.1.4.1.2011.6.187.32.1.2 | ColumnhwDocsQamFmInputTs | read-create | current | Indicates the index of a input TS. |
| 1.3.6.1.4.1.2011.6.187.32.1.3 | ColumnhwDocsQamFmInputProgramID | read-create | current | Indicates the program ID in the input TS. |
| 1.3.6.1.4.1.2011.6.187.32.1.4 | ColumnhwDocsQamFmChannelID | read-create | current | Indicates the channel ID. |
| 1.3.6.1.4.1.2011.6.187.32.1.5 | ColumnhwDocsQamFmMapRowStatus | read-create | current | Row status, used to query, create, and delete a FM mapping. It supports the active(1), createAndGo(4) and destroy(6) operations. During query, the value of thi… |
| 1.3.6.1.4.1.2011.6.187.33 | TablehwDocsQamFMPortConfigTable | not-accessible | current | Indicates the FM domain port table used to manage relationships between FM domains and ports. The index of this table is ifIndex. |
| 1.3.6.1.4.1.2011.6.187.33.1 | RowhwDocsQamFMPortConfigEntry | not-accessible | current | Indicates the FM domain port table used to manage relationships between FM domains and ports. The index of this entry is ifIndex. |
| 1.3.6.1.4.1.2011.6.187.33.1.1 | ColumnhwDocsQamFMPortConfigDomainName | read-create | current | Indicates the FM domain name. |
| 1.3.6.1.4.1.2011.6.187.33.1.2 | ColumnhwDocsQamFMPortConfigRowStatus | read-create | current | Row status, used to query, create, modify, and delete a port table. It supports the active(1), createAndGo(4), and destroy(6) operations. During query, the val… |
| 1.3.6.1.4.1.2011.6.187.34 | TablehwDocsQamFmRDSTable | not-accessible | current | Indicates the FM RDS table used to configure the RDS information of a FM mapping in FM domain. The indexes of this table are hwDocsQamFMDomainName and hwDocsQa… |
| 1.3.6.1.4.1.2011.6.187.34.1 | RowhwDocsQamFmRDSEntry | not-accessible | current | Indicates the FM RDS table used to configure the RDS information of a FM mapping in FM domain. The indexes of this entry are hwDocsQamFMDomainName and hwDocsQa… |
| 1.3.6.1.4.1.2011.6.187.34.1.1 | ColumnhwDocsQamFmRDSAdminStatus | read-create | current | Indicates the status of RDS admin, the default value is disable(1). Options: 1. disable(1) -indicates the status of RDS admin is disable. 2. enable(2) -indicat… |
| 1.3.6.1.4.1.2011.6.187.34.1.2 | ColumnhwDocsQamFmRDSProgramType | read-create | current | Indicates the type of program. Refers to the section 3.2.1.2 of EN50067_RDS_Standard.pdf 0 - None. 1 - News. 2 - Affairs. 3 - Info. 4 - Sport. 5 - Educate. 6 -… |
| 1.3.6.1.4.1.2011.6.187.34.1.3 | ColumnhwDocsQamFmRDSProgramServiceName | read-create | current | Indicates the service name of the FM program. |
| 1.3.6.1.4.1.2011.6.187.34.1.4 | ColumnhwDocsQamFmRDSRadioText | read-create | current | Indicates the radio text of the FM program. |
| 1.3.6.1.4.1.2011.6.187.34.1.5 | ColumnhwDocsQamFmRDSCoverageArea | read-create | current | Indicates the coverage area of the FM program. Refers to the section 3.2.1.1 of EN50067_RDS_Standard.pdf. 0 - L. 1 - I. 2 - N. 3 - S. 4 - R1. 5 - R2 6 - R3. 7 … |
| 1.3.6.1.4.1.2011.6.187.34.1.6 | ColumnhwDocsQamFmRDSProgramReference | read-create | current | Indicates the program reference value. The default value is 0. |
| 1.3.6.1.4.1.2011.6.187.34.1.7 | ColumnhwDocsQamFmRDSMode | read-write | current | Indicates the mode of RDS. The default value is manual(1). Options: 1. manual(1) -indicates RDS is configured manually. 2. embedded(2)-indicates RDS informatio… |
| 1.3.6.1.4.1.2011.6.187.34.1.8 | ColumnhwDocsQamFmRDSCTDef | read-write | current | Indicates default Clock-time and date switch of RDS. The default value is invalid(3). Options: 1. enable(1) -indicates the switch is on. 2. disable(2) -indicat… |
| 1.3.6.1.4.1.2011.6.187.34.1.9 | ColumnhwDocsQamFmRDSCountryCodeValue | read-only | current | Indicates the country of the FM program. The default value is 0. |
| 1.3.6.1.4.1.2011.6.187.34.1.10 | ColumnhwDocsQamFmRDSTATP | read-only | current | Indicates Traffic-announcement identification and Traffic-programme identification of RDS. The format is 2 bits. The default value is 0. Refers to the section … |
| 1.3.6.1.4.1.2011.6.187.34.1.11 | ColumnhwDocsQamFmRDSDI | read-only | current | Indicates the Decoder Identification and Dynamic PTY Indicator.The format is 4 bits. The default value is 0. Refers to the section 3.2.1.4 of EN50067_RDS_Stand… |
| 1.3.6.1.4.1.2011.6.187.34.1.12 | ColumnhwDocsQamFmRDSMS | read-only | current | Indicates the state of Music Speech switch. The format is 1 bit. The default value is 0, indicating the Music Speech switch is off. Refers to the section 3.2.1… |
| 1.3.6.1.4.1.2011.6.187.34.1.13 | ColumnhwDocsQamFmRDSCT | read-only | current | Indicates Clock-time and date switch. The default value is invalid(3). Options: 1. on(1) -indicates the switch is on. 2. off(2) -indicates the switch is off. 3… |
| 1.3.6.1.4.1.2011.6.187.34.1.14 | ColumnhwDocsQamFmRDSRealTimeClock | read-only | current | Indicate date and time(with time zone) of RDS. The default value is 1900-01-01 00:00:00. |
| 1.3.6.1.4.1.2011.6.187.35 | TablehwDocsQamDVBPIDMappingTable | not-accessible | current | Indicates the DVB PID mapping table used to configure the input TS list, input PID list, output PID list of channels in a DVB domain. The indexes of this table… |
| 1.3.6.1.4.1.2011.6.187.35.1 | RowhwDocsQamDVBPIDMappingEntry | not-accessible | current | Indicates the DVB PID mapping table used to configure the input TS list, input PID list, output PID list of channels in a DVB domain. The indexes of this entry… |
| 1.3.6.1.4.1.2011.6.187.35.1.1 | ColumnhwDocsQamDVBPIDMappingChannelID | not-accessible | current | Indicates the ChannelID. |
| 1.3.6.1.4.1.2011.6.187.35.1.2 | ColumnhwDocsQamDVBPIDMappingInputTSList | read-create | current | Indicates the input TS list. Input TS ID consists of two bytes and must be in one-to-one mapping with input PID list and output PID list. |
| 1.3.6.1.4.1.2011.6.187.35.1.3 | ColumnhwDocsQamDVBPIDMappingInputPIDList | read-create | current | Indicates the input PID list. Input PID consists of two bytes and must be in one-to-one mapping with input TS list and output PID list. |
| 1.3.6.1.4.1.2011.6.187.35.1.4 | ColumnhwDocsQamDVBPIDMappingOutputPIDList | read-create | current | Indicates the output PID list. Output PID consists of two bytes and must be in one-to-one mapping with input TS list and input PID list. |
| 1.3.6.1.4.1.2011.6.187.36 | NotificationhwDocsQamDVBRTPSequenceErrorTrap | current | The hwDocsQamDVBRTPSequenceErrorEvent will be sent when the counter of RTP sequence error reaches the uplimit. | |
| 1.3.6.1.4.1.2011.6.187.37 | TablehwDocsQamDVBProcessGroupTable | not-accessible | current | Indicates the table for configuring the working board and protection board in the DVB service processing protection group, and perform switchover. The index of… |
| 1.3.6.1.4.1.2011.6.187.37.1 | RowhwDocsQamDVBProcessGroupEntry | not-accessible | current | Indicates the table for configuring the working board and protection board in the DVB service processing protection group, and perform switchover. The index of… |
| 1.3.6.1.4.1.2011.6.187.37.1.1 | ColumnhwDocsQamDVBProcessGroupID | not-accessible | current | Indicates the ID of a DVB service processing protection group. |
| 1.3.6.1.4.1.2011.6.187.37.1.2 | ColumnhwDocsQamDVBProcessGroupWorkFrameID | read-create | current | Indicates the ID of the frame that accomdates the working board in a DVB service processing protection group. |
| 1.3.6.1.4.1.2011.6.187.37.1.3 | ColumnhwDocsQamDVBProcessGroupWorkSlotID | read-create | current | Indicates the ID of the slot that accommodates the working board in a DVB service processing protection group. |
| 1.3.6.1.4.1.2011.6.187.37.1.4 | ColumnhwDocsQamDVBProcessGroupProtectFrameID | read-create | current | Indicates the ID of the frame that accommodates the protection board in a DVB service processing protection group. |
| 1.3.6.1.4.1.2011.6.187.37.1.5 | ColumnhwDocsQamDVBProcessGroupProtectSlotID | read-create | current | Indicates the ID of the slot that accommodates the protection board in a DVB service processing protection group. |
| 1.3.6.1.4.1.2011.6.187.37.1.6 | ColumnhwDocsQamDVBProcessGroupSwitchover | read-write | current | Indicates switchover in a DVB service processing protection group. The default value is none(255). Options: 1. switchover(1) -Perform a switchover operation. 2… |
| 1.3.6.1.4.1.2011.6.187.37.1.7 | ColumnhwDocsQamDVBProcessGroupActiveFrameID | read-only | current | Indicates the ID of the frame that accommodates the active board in a DVB service processing protection group. |
| 1.3.6.1.4.1.2011.6.187.37.1.8 | ColumnhwDocsQamDVBProcessGroupActiveSlotID | read-only | current | Indicates the ID of the slot that accommodates the active board in a DVB service processing protection group. |
| 1.3.6.1.4.1.2011.6.187.37.1.9 | ColumnhwDocsQamDVBProcessGroupActive | read-only | current | Indicates the role of the active board in a DVB service processing protection group. Options: 1. work(1) -Indicates that the working board in a DVB service pro… |
| 1.3.6.1.4.1.2011.6.187.37.1.10 | ColumnhwDocsQamDVBProcessGroupRowStatus | read-create | current | Indicates a row status for querying, creating, modifying, and deleting a DVB service processing protection group table. It supports active(1), createAndGo(4), … |
| 1.3.6.1.4.1.2011.6.187.38 | TablehwDocsQamInputPIDInfoTable | not-accessible | current | Indicates the input PID info table used to display the packet identifier (PID), PID type, PID subtype, PID rate, maximum PID rate, minimum PID rate, PID scramb… |
| 1.3.6.1.4.1.2011.6.187.38.1 | RowhwDocsQamInputPIDInfoEntry | not-accessible | current | Indicates the input PID info table used to display the packet identifier (PID), PID type, PID subtype, PID rate, maximum PID rate, minimum PID rate, PID scramb… |
| 1.3.6.1.4.1.2011.6.187.38.1.1 | ColumnhwDocsQamInputPIDIndex | not-accessible | current | Indicates the input PID index, whose value is obtained by adding 1 to the value of hwDocsQamInputPID. |
| 1.3.6.1.4.1.2011.6.187.38.1.2 | ColumnhwDocsQamInputPID | read-only | current | Indicates the value of input PID. |
| 1.3.6.1.4.1.2011.6.187.38.1.3 | ColumnhwDocsQamInputPIDType | read-only | current | Indicates the input PID type. The default value is unknown(255), indicating the unknown type. |
| 1.3.6.1.4.1.2011.6.187.38.1.4 | ColumnhwDocsQamInputPIDStreamType | read-only | current | When the value of hwDocsQamInputPIDStreamType is 12, hwDocsQamInputPIDStreamType indicates the corresponding media type. For details about its value, see ISO/I… |
| 1.3.6.1.4.1.2011.6.187.38.1.5 | ColumnhwDocsQamInputPIDRate | read-only | current | Indicates the rate of the input PID. Unit: kbit/s. |
| 1.3.6.1.4.1.2011.6.187.38.1.6 | ColumnhwDocsQamInputPIDMaxRate | read-only | current | Indicates the maximum rate of the input PID. Unit: kbit/s. |
| 1.3.6.1.4.1.2011.6.187.38.1.7 | ColumnhwDocsQamInputPIDMinRate | read-only | current | Indicates the minimum rate of the input PID. Unit: kbit/s. |
| 1.3.6.1.4.1.2011.6.187.38.1.8 | ColumnhwDocsQamInputPIDScambled | read-only | current | Indicates the input PID scrambling information. options: notScambled(1) evenScambled(2) oddScambled(3) |
| 1.3.6.1.4.1.2011.6.187.38.1.9 | ColumnhwDocsQamInputPIDCCErrorCount | read-only | current | Indicates the CC error count of the input PID. |
| 1.3.6.1.4.1.2011.6.187.38.1.10 | ColumnhwDocsQamInputPIDPCRReference | read-only | current | Indicates the PCR association of the input PID. The default value is false. |
| 1.3.6.1.4.1.2011.6.187.38.1.11 | ColumnhwDocsQamInputPIDProgramIDReference | read-only | current | Indicates the ID of the program associated with the PID. The default value is 4294967295, indicating no associated program. |
| 1.3.6.1.4.1.2011.6.187.38.1.12 | ColumnhwDocsQamInputPIDProgramNameReference | read-only | current | Indicates the name of the program associated with the PID. The default value is an empty character string, indicating no associated program name.. |
| 1.3.6.1.4.1.2011.6.187.39 | TablehwDocsQamInputTSPIDTable | not-accessible | current | Indicates the input TS PID table used to display the number of PIDs, PID list, and PID list status mask of the input TS. The indexes of this table is hwDocsQam… |
| 1.3.6.1.4.1.2011.6.187.39.1 | RowhwDocsQamInputTSPIDEntry | not-accessible | current | Indicates the input TS PID table used to display the number of PIDs, PID list, and PID list status mask of the input TS. The indexes of this entry is hwDocsQam… |
| 1.3.6.1.4.1.2011.6.187.39.1.1 | ColumnhwDocsQamInputTSPIDNumber | read-only | current | Indicates the number of the input TS PID. |
| 1.3.6.1.4.1.2011.6.187.39.1.2 | ColumnhwDocsQamInputTSPIDList | read-only | current | Format: 2 bytes in network byte order, which indicates a PID. A maximum of 256 PIDs are supported. a 2-byte bit-field value defined as follows: Bit 0:xx Bit 1:… |
| 1.3.6.1.4.1.2011.6.187.39.1.3 | ColumnhwDocsQamInputTSPIDStateMask | read-only | current | Indicates the PID list status mask of the input TS. The default value is an empty character string, indicating no PID list status mask. Format: 2 bytes in netw… |
| 1.3.6.1.4.1.2011.6.187.40 | NodehwDocsQamLocationIDInsertionConfigObject | |||
| 1.3.6.1.4.1.2011.6.187.40.1 | ScalarhwDocsQamLocationIDInsertionSwitch | read-write | current | Indicates the insertion function of the location ID. The default value is disabled(2). Options: 1. enabled(1) -indicates that the insertion function of the loc… |
| 1.3.6.1.4.1.2011.6.187.40.2 | ScalarhwDocsQamLocationIDInsertionPID | read-write | current | Indicates the PID for the insertion function of the location ID. Range: 3-15 Default: 14 |
| 1.3.6.1.4.1.2011.6.187.40.3 | ScalarhwDocsQamLocationIDInsertionInterval | read-write | current | Indicates the Tx interval for the insertion function of the location ID. Range: 2-10 Unit: second Default: 2 |
| 1.3.6.1.4.1.2011.6.187.41 | TablehwDocsQamLocationIDConfigTable | not-accessible | current | Indicates the location ID of a port on the extended subrack. The index of this table is ifIndex. |
| 1.3.6.1.4.1.2011.6.187.41.1 | RowhwDocsQamLocationIDConfigEntry | not-accessible | current | Indicates the location ID of a port on the extended subrack. The index of this entry is ifIndex. |
| 1.3.6.1.4.1.2011.6.187.41.1.1 | ColumnhwDocsQamLocationID | read-write | current | Indicates the configured location ID. 4294967295 indicates the unconfigured location ID. Range: 0..4294967295 Default: 4294967295 |
| 1.3.6.1.4.1.2011.6.187.42 | TablehwDocsQamInputTSProgramEsTable | not-accessible | current | Indicates the program elementary stream (ES) table of an input TS, which is used to query the rate, maximum rate, minimum rate, number of CAs, CA PID list, and… |
| 1.3.6.1.4.1.2011.6.187.42.1 | RowhwDocsQamInputTSProgramEsEntry | not-accessible | current | Indicates the program elementary stream (ES) table of an input TS, which is used to query the rate, maximum rate, minimum rate, number of CAs, CA PID list, and… |
| 1.3.6.1.4.1.2011.6.187.42.1.1 | ColumnhwDocsQamInputTSProgramEsIndex | not-accessible | current | Indicates the index of program ES in input TS. |
| 1.3.6.1.4.1.2011.6.187.42.1.2 | ColumnhwDocsQamInputTSProgramEsType | read-only | current | Indicates the type of program ES in input TS. For details about its value, see ISO/IEC 13818-1 [18] Program Map Table (PMT). The default value is 0. |
| 1.3.6.1.4.1.2011.6.187.42.1.3 | ColumnhwDocsQamInputTSProgramEsPID | read-only | current | Indicates the PID of program ES in input TS. |
| 1.3.6.1.4.1.2011.6.187.42.1.4 | ColumnhwDocsQamInputTSProgramEsRate | read-only | current | Indicates the rate of program ES in input TS. Unit: kbit/s. The default value is 0. |
| 1.3.6.1.4.1.2011.6.187.42.1.5 | ColumnhwDocsQamInputTSProgramEsMaxRate | read-only | current | Indicates the maximum rate of program ES in input TS. Unit: kbit/s. The default value is 0. |
| 1.3.6.1.4.1.2011.6.187.42.1.6 | ColumnhwDocsQamInputTSProgramEsMinRate | read-only | current | Indicates the minimum rate of program ES in input TS. Unit: kbit/s. The default value is 0. |
| 1.3.6.1.4.1.2011.6.187.42.1.7 | ColumnhwDocsQamInputTSProgramEsCaNumber | read-only | current | Indicates the CA number of program ES in input TS. |
| 1.3.6.1.4.1.2011.6.187.42.1.8 | ColumnhwDocsQamInputTSProgramEsCaPIDList | read-only | current | Indicates the CA PID list of an input program ES. A PID is displayed as a 2-byte string in network order. A maximum of 4 CAs are supported. The default value i… |
| 1.3.6.1.4.1.2011.6.187.42.1.9 | ColumnhwDocsQamInputTSProgramEsCaSystemIDList | read-only | current | Indicates the CA system ID list of an input program ES. A CA system ID is displayed as a 2-byte string in network order. A maximum of 4 CAs are supported. |
| 1.3.6.1.4.1.2011.6.187.43 | TablehwDocsQamOutputTSTable | not-accessible | current | Indicates the output TS table. The index of this table is ifIndex. |
| 1.3.6.1.4.1.2011.6.187.43.1 | RowhwDocsQamOutputTSEntry | not-accessible | current | Indicates the output TS table. The index of this table is ifIndex. |
| 1.3.6.1.4.1.2011.6.187.43.1.1 | ColumnhwDocsQamOutputTSProgramNumber | read-only | current | Indicates the program number in output TS. |
| 1.3.6.1.4.1.2011.6.187.43.1.2 | ColumnhwDocsQamOutputTSRate | read-only | current | Indicates the rate of program in output TS. Unit: kbit/s. The default value is 0. |
| 1.3.6.1.4.1.2011.6.187.43.1.3 | ColumnhwDocsQamOutputTSMaxRate | read-only | current | Indicates the maximum rate of program in output TS. Unit: kbit/s. The default value is 0. |
| 1.3.6.1.4.1.2011.6.187.43.1.4 | ColumnhwDocsQamOutputTSMinRate | read-only | current | Indicates the mininum rate of program in output TS. Unit: kbit/s. The default value is 0. |
| 1.3.6.1.4.1.2011.6.187.43.1.5 | ColumnhwDocsQamOutputTSDiscards | read-only | current | Indicates the packet loss of output TS. |
| 1.3.6.1.4.1.2011.6.187.43.1.6 | ColumnhwDocsQamOutputTSEPG | read-only | current | Indicates whether the transport stream is treated as the EPG input. The default value is false(2). |
| 1.3.6.1.4.1.2011.6.187.43.1.7 | ColumnhwDocsQamOutputTSStatisticsOperMode | read-write | current | Clear output TS statistics. Options: 1. clearStatistic(1) -indicates clearing the statistics of output TS. |
| 1.3.6.1.4.1.2011.6.187.44 | TablehwDocsQamOutputTSProgramEsTable | not-accessible | current | Indicates the program elementary stream (ES) table of an output TS, which is used to query the rate, maximum rate, minimum rate, number of CAs, CA PID list, an… |
| 1.3.6.1.4.1.2011.6.187.44.1 | RowhwDocsQamOutputTSProgramEsEntry | not-accessible | current | Indicates the program elementary stream (ES) table of an output TS, which is used to query the rate, maximum rate, minimum rate, number of CAs, CA PID list, an… |
| 1.3.6.1.4.1.2011.6.187.44.1.1 | ColumnhwDocsQamOutputTSProgramEsIndex | not-accessible | current | Indicates the index of program ES in output TS. |
| 1.3.6.1.4.1.2011.6.187.44.1.2 | ColumnhwDocsQamOutputTSProgramEsType | read-only | current | Indicates the type of program ES in output TS. For details about its value, see ISO/IEC 13818-1 [18] Program Map Table (PMT). The default value is 0. |
| 1.3.6.1.4.1.2011.6.187.44.1.3 | ColumnhwDocsQamOutputTSProgramEsPID | read-only | current | Indicates the PID of program ES in output TS. |
| 1.3.6.1.4.1.2011.6.187.44.1.4 | ColumnhwDocsQamOutputTSProgramEsRate | read-only | current | Indicates the rate of program ES in output TS. Unit: kbit/s. The default value is 0. |
| 1.3.6.1.4.1.2011.6.187.44.1.5 | ColumnhwDocsQamOutputTSProgramEsMaxRate | read-only | current | Indicates the maximum rate of program ES in output TS. Unit: kbit/s. The default value is 0. |
| 1.3.6.1.4.1.2011.6.187.44.1.6 | ColumnhwDocsQamOutputTSProgramEsMinRate | read-only | current | Indicates the minimum rate of program ES in output TS. Unit: kbit/s. The default value is 0. |
| 1.3.6.1.4.1.2011.6.187.44.1.7 | ColumnhwDocsQamOutputTSProgramEsCaNumber | read-only | current | Indicates the CA number of program ES in output TS. |
| 1.3.6.1.4.1.2011.6.187.44.1.8 | ColumnhwDocsQamOutputTSProgramEsCaPIDList | read-only | current | Indicates the CA PID list of an output program ES. A PID is displayed as a 2-byte string in network order. A maximum of 4 CAs are supported. The default value … |
| 1.3.6.1.4.1.2011.6.187.44.1.9 | ColumnhwDocsQamOutputTSProgramEsCaSystemIDList | read-only | current | Indicates the CA system ID list of an output program ES. A CA system ID is displayed as a 2-byte string in network order. A maximum of 4 CAs are supported. |
| 1.3.6.1.4.1.2011.6.187.45 | TablehwDocsQamOutputPIDInfoTable | not-accessible | current | Indicates the output PID info table used to display the packet identifier (PID), PID type, PID subtype, PID rate, maximum PID rate, minimum PID rate, PID scram… |
| 1.3.6.1.4.1.2011.6.187.45.1 | RowhwDocsQamOutputPIDInfoEntry | not-accessible | current | Indicates the output PID info table used to display the packet identifier (PID), PID type, PID subtype, PID rate, maximum PID rate, minimum PID rate, PID scram… |
| 1.3.6.1.4.1.2011.6.187.45.1.1 | ColumnhwDocsQamOutputPIDIndex | not-accessible | current | Indicates the output PID index, whose value is obtained by adding 1 to the value of hwDocsQamOutputPID. |
| 1.3.6.1.4.1.2011.6.187.45.1.2 | ColumnhwDocsQamOutputPID | read-only | current | Indicates the value of output PID. |
| 1.3.6.1.4.1.2011.6.187.45.1.3 | ColumnhwDocsQamOutputPIDType | read-only | current | Indicates the output PID type. The default value is unknown(255), indicating the unknown type. |
| 1.3.6.1.4.1.2011.6.187.45.1.4 | ColumnhwDocsQamOutputPIDStreamType | read-only | current | When the value of hwDocsQamOutputPIDStreamType is 12, hwDocsQamOutputPIDStreamType indicates the corresponding media type. For details about its value, see ISO… |
| 1.3.6.1.4.1.2011.6.187.45.1.5 | ColumnhwDocsQamOutputPIDRate | read-only | current | Indicates the rate of the output PID. Unit: kbit/s. |
| 1.3.6.1.4.1.2011.6.187.45.1.6 | ColumnhwDocsQamOutputPIDMaxRate | read-only | current | Indicates the maximum rate of the output PID. Unit: kbit/s. |
| 1.3.6.1.4.1.2011.6.187.45.1.7 | ColumnhwDocsQamOutputPIDMinRate | read-only | current | Indicates the minimum rate of the output PID. Unit: kbit/s. |
| 1.3.6.1.4.1.2011.6.187.45.1.8 | ColumnhwDocsQamOutputPIDScambled | read-only | current | Indicates the output PID scrambling information. options: notScambled(1) evenScambled(2) oddScambled(3) |
| 1.3.6.1.4.1.2011.6.187.45.1.9 | ColumnhwDocsQamOutputPIDCCErrorCount | read-only | current | Indicates the CC error count of the output PID. |
| 1.3.6.1.4.1.2011.6.187.45.1.10 | ColumnhwDocsQamOutputPIDPCRReference | read-only | current | Indicates the PCR association of the output PID. The default value is false. |
| 1.3.6.1.4.1.2011.6.187.45.1.11 | ColumnhwDocsQamOutputPIDProgramIDReference | read-only | current | Indicates the ID of the program associated with the PID. The default value is 4294967295, indicating no associated program. |
| 1.3.6.1.4.1.2011.6.187.45.1.12 | ColumnhwDocsQamOutputPIDProgramNameReference | read-only | current | Indicates the name of the program associated with the PID. The default value is an empty character string, indicating no associated program name.. |
| 1.3.6.1.4.1.2011.6.187.46 | TablehwDocsQamOutputTSPIDTable | not-accessible | current | Indicates the output TS PID table used to display the number of PIDs, PID list, and PID list status mask of the output TS. The indexes of this table is ifIndex. |
| 1.3.6.1.4.1.2011.6.187.46.1 | RowhwDocsQamOutputTSPIDEntry | not-accessible | current | Indicates the output TS PID table used to display the number of PIDs, PID list, and PID list status mask of the output TS. The indexes of this entry is ifIndex. |
| 1.3.6.1.4.1.2011.6.187.46.1.1 | ColumnhwDocsQamOutputTSPIDNumber | read-only | current | Indicates the number of the output TS PID. |
| 1.3.6.1.4.1.2011.6.187.46.1.2 | ColumnhwDocsQamOutputTSPIDList | read-only | current | Format: 2 bytes in network byte order, which indicates a PID. A maximum of 256 PIDs are supported. a 2-byte bit-field value defined as follows: Bit 0:xx Bit 1:… |
| 1.3.6.1.4.1.2011.6.187.46.1.3 | ColumnhwDocsQamOutputTSPIDStateMask | read-only | current | Indicates the PID list status mask of the output TS. The default value is an empty character string, indicating no PID list status mask. Format: 2 bytes in net… |
| 1.3.6.1.4.1.2011.6.187.47 | TablehwDocsQamEPGTable | not-accessible | current | Indicates a table used to query the electronic program guide (EPG) status of a DVB video domain. The indexes of this table is ifIndex and hwDocsQamEPGProgramID. |
| 1.3.6.1.4.1.2011.6.187.47.1 | RowhwDocsQamEPGEntry | not-accessible | current | Indicates a table used to query the electronic program guide (EPG) status of a DVB video domain. The indexes of this table is ifIndex and hwDocsQamEPGProgramID. |
| 1.3.6.1.4.1.2011.6.187.47.1.1 | ColumnhwDocsQamEPGProgramID | read-only | current | Indicates the output program ID. |
| 1.3.6.1.4.1.2011.6.187.47.1.2 | ColumnhwDocsQamEPGProgramName | read-only | current | Indicates the output program name. The default value is null string. |
| 1.3.6.1.4.1.2011.6.187.47.1.3 | ColumnhwDocsQamEPGProgramInputTSIndex | read-only | current | Indicates the index of the input TS corresponding to a program. The default value is 4294967295, which indicates that no input TS is associated. |
| 1.3.6.1.4.1.2011.6.187.47.1.4 | ColumnhwDocsQamEPGProgramInputProgramID | read-only | current | Indicates the input program id corresponding to a program. The default value is 4294967295, which indicates that no input program is associated. |
| 1.3.6.1.4.1.2011.6.187.47.1.5 | ColumnhwDocsQamEPGSourceTSIndex | read-only | current | Indicates the index of the source TS corresponding to an EPG. The default value is 4294967295, which indicates that no input TS is associated. |
| 1.3.6.1.4.1.2011.6.187.47.1.6 | ColumnhwDocsQamEPGSourceProgramID | read-only | current | Indicates the ID of the source program corresponding to an EPG. The default value is 4294967295, which indicates that no input program is associated. |
| 1.3.6.1.4.1.2011.6.187.47.1.7 | ColumnhwDocsQamEPGPresentAndFollowingMatched | read-only | current | Indicates whether an EPG matches the present/follow-up event information. true indicates that they are matched and the default value false indicates that they … |
| 1.3.6.1.4.1.2011.6.187.47.1.8 | ColumnhwDocsQamEPGScheduleMatched | read-only | current | Indicates whether an EPG matches event schedule information. true indicates that they are matched and the default value false indicates that they are not match… |
| 1.3.6.1.4.1.2011.6.187.48 | TablehwDocsQamVODSummaryTable | not-accessible | current | Indicates the video program abstract. The index of this table is ifIndex. |
| 1.3.6.1.4.1.2011.6.187.48.1 | RowhwDocsQamVODSummaryEntry | not-accessible | current | Indicates the video program abstract. The index of this table is ifIndex. |
| 1.3.6.1.4.1.2011.6.187.48.1.1 | ColumnhwDocsQamVODProgramNumberTotal | read-only | current | Indicates the number of VOD programs on a RF port. |
| 1.3.6.1.4.1.2011.6.187.48.1.2 | ColumnhwDocsQamVODProgramNumberOnline | read-only | current | Indicates the number of online VOD programs on a RF port. |
| 1.3.6.1.4.1.2011.6.187.49 | TablehwDocsQamDVBChannelMonitoringControlTable | not-accessible | current | Indicates the table for DVB channel monitoring, which is used to configure channel monitoring locking and query the ID of the channel being monitored. The inde… |
| 1.3.6.1.4.1.2011.6.187.49.1 | RowhwDocsQamDVBChannelMonitoringControlEntry | not-accessible | current | Indicates the table for DVB channel monitoring, which is used to configure channel monitoring locking and query the ID of the channel being monitored. The inde… |
| 1.3.6.1.4.1.2011.6.187.49.1.1 | ColumnhwDocsQamDVBChannelMonitoringControlCurrentChannelID | read-only | current | Indicates the ID of the channel being monitored. The default value is 0, indicates that no channel is in the monitoring state. |
| 1.3.6.1.4.1.2011.6.187.49.1.2 | ColumnhwDocsQamDVBChannelMonitoringControlLockedChannelID | read-write | current | Indicates the ID of the channel locked by monitoring. The default value is 0, indicates that no channel is locked by monitoring. |
| 1.3.6.1.4.1.2011.6.187.50 | TablehwDocsQamDVBChannelMonitoringTable | not-accessible | current | Indicates the DVB channel monitoring table, which is used to query the monitoring information and reset DVB monitoring. The indexes of this table is ifIndex. |
| 1.3.6.1.4.1.2011.6.187.50.1 | RowhwDocsQamDVBChannelMonitoringEntry | not-accessible | current | Indicates the DVB channel monitoring table, which is used to query the monitoring information and reset DVB monitoring. The indexes of this table is ifIndex. |
| 1.3.6.1.4.1.2011.6.187.50.1.1 | ColumnhwDocsQamChannelMonitoringRTPSequenceErrorCounter | read-only | current | Indicates RTP error statistics of a monitored channel. |
| 1.3.6.1.4.1.2011.6.187.50.1.2 | ColumnhwDocsQamChannelMonitoringOperMode | read-write | current | Indicates reseting channel monitoring. Options: 1. reset(1) -indicates reseting channel monitoring. |
| 1.3.6.1.4.1.2011.6.187.50.1.3 | ColumnhwDocsQamChannelMonitoringPIDList | read-only | current | Indicates the PID list of a monitored channel. The default value is null string. Format: 2 bytes in network byte order, which indicates a PID. A maximum of 256… |
| 1.3.6.1.4.1.2011.6.187.50.1.4 | ColumnhwDocsQamChannelMonitoringPIDStateMask | read-only | current | Indicates the PID list status mask of the monitoring channel. The default value is an empty character string. Format: 2 bytes in network byte order, which indi… |
| 1.3.6.1.4.1.2011.6.187.51 | TablehwDocsQamDVBChannelPidMonitoringTable | not-accessible | current | Indicates PID table for DVB channel monitoring. The indexes of this table is ifIndex and hwDocsQamDVBChannelMonitoringPIDIndex. |
| 1.3.6.1.4.1.2011.6.187.51.1 | RowhwDocsQamDVBChannelPidMonitoringEntry | not-accessible | current | Indicates PID table for DVB channel monitoring. The indexes of this table is ifIndex and hwDocsQamDVBChannelMonitoringPIDIndex. |
| 1.3.6.1.4.1.2011.6.187.51.1.1 | ColumnhwDocsQamDVBChannelMonitoringPIDIndex | not-accessible | current | Indicates PID index of a DVB monitoring channel. |
| 1.3.6.1.4.1.2011.6.187.51.1.2 | ColumnhwDocsQamDVBChannelMonitoringPID | read-only | current | Indicates the PID of a DVB monitoring channel. |
| 1.3.6.1.4.1.2011.6.187.51.1.3 | ColumnhwDocsQamDVBChannelMonitoringPIDCCErrorCount | read-only | current | Indicates the number of PID CC errors of a DVB monitoring channel. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| HwEqamInputPIDType | INTEGER { pat(1), pmt(2), cat(3), nit(4), sdt(5), eit(6), tdttot(7), ecm(8), emm(9), pcr(10), null(11), media(12), unknown(255) } | current | Indicates the input PID type. Options: pat(1) pmt(2) cat(3) nit(4) sdt(5) eit(6) tdttot(7) ecm(8) emm(9) pcr(10) null(11) media(12) unknown(255) |
| HwEqamPsiPolicyChannnel | INTEGER { stop(1), play(2), default(3) } | current | PSI/SI output policy for channel. 'stop' indicates PSI/SI output is disabled. 'play' indicates PSI/SI will be enabled for playout. 'default' indicates the output policy inherits from the DVB domain. |
| HwEqamPsiPolicyDvbDomain | INTEGER { stop(1), play(2) } | current | PSI/SI output policy for DVB domain. 'stop' indicates PSI/SI output is disabled. 'play' indicates PSI/SI will be enabled for playout. |