HUAWEI-ETHERNET-OPTICMODULE-MIB
221 objects
This mib is used for managing Ethernet optics module.
Imported Objects
| HUAWEI-DEVICE-MIB | hwFrameIndex hwPortDesc hwPortIndex hwSlotIndex |
| HUAWEI-MIB | huaweiMgmt |
| IF-MIB | ifIndex InterfaceIndex |
| SNMPv2-SMI | Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE TimeTicks Unsigned32 |
| SNMPv2-TC | MacAddress RowStatus TEXTUAL-CONVENTION TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.2011.5.14 | IdentityhwEthernetPort | This mib is used for managing Ethernet optics module. | ||
| 1.3.6.1.4.1.2011.5.14.6 | NodehwOpticsModuleInformation | |||
| 1.3.6.1.4.1.2011.5.14.6.1 | TablehwOpticsModuleInformationTable | not-accessible | current | Indicates the optical module table of an Ethernet port. It is used for querying the information about the optical module of an Ethernet port. The index of this… |
| 1.3.6.1.4.1.2011.5.14.6.1.1 | RowhwOpticsModuleInformationEntry | not-accessible | current | Indicates the optical module table of an Ethernet port. It is used for querying the information about the optical module of an Ethernet port. The index of this… |
| 1.3.6.1.4.1.2011.5.14.6.1.1.1 | ColumnhwOpticsMDIdentifier | read-only | current | Indicate the identifier of optical module. Options: 1. unknown(1) -unknown the identifier of optical module 2. gbic(2) -the identifier of optical module is gbi… |
| 1.3.6.1.4.1.2011.5.14.6.1.1.2 | ColumnhwOpticsMDExtID | read-only | current | Indicate the extended type of optical module. Options: 1. notSpecifiedOrNotCompliant(1) -the extended type of optical module is notSpecifiedOrNotCompliant 2. m… |
| 1.3.6.1.4.1.2011.5.14.6.1.1.3 | ColumnhwOpticsMDConnector | read-only | current | Indicate the type of optical module connector. Options: 1. unknown(1) -unknown the type of optical module connector 2. sc(2) -the type of optical module connec… |
| 1.3.6.1.4.1.2011.5.14.6.1.1.4 | ColumnhwOpticsMDEncoding | read-only | current | Indicate the encoding mechanism. Options: 1. unspecified(1) -the encoding mechanism is unspecified 2. encodingMethod8B10B(2) -the encoding mechanism is encodin… |
| 1.3.6.1.4.1.2011.5.14.6.1.1.5 | ColumnhwOpticsMDBrNominal | read-only | current | Nominal bit rate. Unit: 100 MBits/sec |
| 1.3.6.1.4.1.2011.5.14.6.1.1.6 | ColumnhwOpticsMDLength9Micronkm | read-only | current | Indicate the link length that is supported by the transceiver while operating in compliance with the applicable standards using 9 micron Single-mode Fiber. The… |
| 1.3.6.1.4.1.2011.5.14.6.1.1.7 | ColumnhwOpticsMDLength9Micron | read-only | current | Indicate the link length that is supported by the transceiver while operating in compliance with the applicable standards using 9 micron Single-mode Fiber. The… |
| 1.3.6.1.4.1.2011.5.14.6.1.1.8 | ColumnhwOpticsMDLength50Micron | read-only | current | Indicate link length that is supported by the transceiver while operating in compliance with applicable standards using 50 micron multi-mode OM2 [500MHz*km] fi… |
| 1.3.6.1.4.1.2011.5.14.6.1.1.9 | ColumnhwOpticsMDLength62Micron5 | read-only | current | Indicate link length that is supported by the transceiver while operating in compliance with applicable standards using 62.5 micron multi-mode OM1 [200 MHz*km]… |
| 1.3.6.1.4.1.2011.5.14.6.1.1.10 | ColumnhwOpticsMDLengthCopper | read-only | current | Indicate Link length supported for copper. Unit: 1m |
| 1.3.6.1.4.1.2011.5.14.6.1.1.11 | ColumnhwOpticsMDVendorName | read-only | current | Indicate the vendor name of a optical module. |
| 1.3.6.1.4.1.2011.5.14.6.1.1.12 | ColumnhwOpticsMDVendorOUI | read-only | current | Indicate the vendor IEEE company ID of a optical module. |
| 1.3.6.1.4.1.2011.5.14.6.1.1.13 | ColumnhwOpticsMDVendorPN | read-only | current | Indicate the part number of a optical module provided by vendor. |
| 1.3.6.1.4.1.2011.5.14.6.1.1.14 | ColumnhwOpticsMDVendorRev | read-only | current | Indicate the revision level for part number provided by vendor. |
| 1.3.6.1.4.1.2011.5.14.6.1.1.15 | ColumnhwOpticsMDWaveLength | read-only | current | The laser wavelength. Unit: 1nm |
| 1.3.6.1.4.1.2011.5.14.6.1.1.16 | ColumnhwOpticsMDCcBase | read-only | current | The check code for base ID fields(one byte). |
| 1.3.6.1.4.1.2011.5.14.6.1.1.17 | ColumnhwOpticsMDOptions | read-only | current | Options: 1. rateSelect(1) -RATE_SELECT is implemented 2. txDisableAndTheSerialOutputDisabled(2) -TX_DISABLE is implemented and disables the serial output. 3. t… |
| 1.3.6.1.4.1.2011.5.14.6.1.1.18 | ColumnhwOpticsMDBrMax | read-only | current | The upper bit rate margin. |
| 1.3.6.1.4.1.2011.5.14.6.1.1.19 | ColumnhwOpticsMDBrMin | read-only | current | The lower bit rate margin. |
| 1.3.6.1.4.1.2011.5.14.6.1.1.20 | ColumnhwOpticsMDVendorSN | read-only | current | The serial number of a optical module provided by vendor. |
| 1.3.6.1.4.1.2011.5.14.6.1.1.21 | ColumnhwOpticsMDDateCode | read-only | current | The date code of a optical module. |
| 1.3.6.1.4.1.2011.5.14.6.1.1.22 | ColumnhwOpticsMDDiagnosticMonitoringType | read-only | current | Indicate the diagnostic monitoring type. Options: 1. internallyCalibrated(1) -the diagnostic monitoring type is internallyCalibrated 2. externallyCalibrated(2)… |
| 1.3.6.1.4.1.2011.5.14.6.1.1.23 | ColumnhwOpticsMDEnhancedOptions | read-only | current | Indicate enhanced Options. Options: 1. forAllMonitoredQuantities(1) -optional Alarm/warning flags implemented for all monitored quantities 2. txDisable(2) -opt… |
| 1.3.6.1.4.1.2011.5.14.6.1.1.24 | ColumnhwOpticsMDSFF8472Compliance | read-only | current | Indicate the SFF-8472 standard. Options: 1. undefined(1) -not included or undefined. 2. includesSFF8472V93(2) -includes functionality described in SFF-8472 Rev… |
| 1.3.6.1.4.1.2011.5.14.6.1.1.25 | ColumnhwOpticsMDCcExt | read-only | current | Check code for the Extended ID Fields. |
| 1.3.6.1.4.1.2011.5.14.6.1.1.26 | ColumnhwOpticsMDVendorSpecific | read-only | current | Vendor of Optical module specific information. |
| 1.3.6.1.4.1.2011.5.14.6.1.1.27 | ColumnhwOpticsMDCLEICode | read-only | current | CLEI code supported by eSFP. Length is 10 bytes. |
| 1.3.6.1.4.1.2011.5.14.6.1.1.28 | ColumnhwOpticsMDInfoRemote | read-only | current | Indicates the operation is performed on a remote optical module. Options: 1. remote(1) -the operation is performed on a remote optical module 2. invalid(-1) -i… |
| 1.3.6.1.4.1.2011.5.14.6.1.1.29 | ColumnhwOpticsMDSFPPulsCableTech | read-only | current | Indicates the cable specification compliance. Options: 1. passiveCable(1) -Passive Cable 2. activeCable(2) -Active Cable 2. invalid(-1) -invalid value |
| 1.3.6.1.4.1.2011.5.14.6.1.1.30 | ColumnhwOpticsMDSFPRateId | read-only | current | Indicates the cable specification compliance. Options: 1. sff8079(1) -Defined for SFF-8079 (4/2/1G Rate_Select & AS0/AS1) 2. sff8431RX(2) -Defined for SFF-8431… |
| 1.3.6.1.4.1.2011.5.14.6.1.1.31 | ColumnhwOpticsMDLength50MicronOM3 | read-only | current | Indicate link length that is supported by the transceiver while operating in compliance with applicable standards using 50 micron multi-mode OM2 [2000MHz*km] f… |
| 1.3.6.1.4.1.2011.5.14.6.1.1.32 | ColumnhwOpticsDwdmClass | read-only | current | Extended identifier: WDM class. Options: 1. noWdm(1) -no WDM 2. cwdm(2) -CWDM 3. dwdm(3) -DWDM 4. invalid(-1) -invalid value |
| 1.3.6.1.4.1.2011.5.14.6.1.1.33 | ColumnhwOpticsDwdmPower | read-only | current | Extended identifier: Power level. Options: 1. dwdmPowerLevel1(1) -The power is lower than 1W. 2. dwdmPowerLevel2(2) -The power is between 1W and 1.5W. 3. dwdmP… |
| 1.3.6.1.4.1.2011.5.14.6.1.1.34 | ColumnhwOpticsDwdmMaxTemperature | read-only | current | Max temperature. Invalid value: 2147483647, returned if the optical module is unavailable or not supported. Unit: 0.000001C |
| 1.3.6.1.4.1.2011.5.14.6.1.1.35 | ColumnhwOpticsDwdmMinTemperature | read-only | current | Min temperature. Invalid value: 2147483647, returned if the optical module is unavailable or not supported. Unit: 0.000001C |
| 1.3.6.1.4.1.2011.5.14.6.1.1.36 | ColumnhwOpticsDwdmMaxSupplyCurrent | read-only | current | Max supply current. Invalid value: 2147483647, returned if the optical module is unavailable or not supported. Unit: 0.000001A |
| 1.3.6.1.4.1.2011.5.14.6.1.1.37 | ColumnhwOpticsDwdmChannelSpacing | read-only | current | Fibre channel spacing. Options: 1. channelSpacing200G(1) -The fibre channel spacing is 200GHz. 2. channelSpacing100G(2) -The fibre channel spacing is 100GHZ. 3… |
| 1.3.6.1.4.1.2011.5.14.6.1.1.38 | ColumnhwOpticsDwdmNumberOfChannels | read-only | current | Number of channels. Invalid value: -1, returned if the optical module is unavailable or not supported. |
| 1.3.6.1.4.1.2011.5.14.6.1.1.39 | ColumnhwOpticsDwdmWaveLength | read-only | current | Laser wavelength. Invalid value: -1, returned if the optical module is unavailable or not supported. Unit: 0.01nm |
| 1.3.6.1.4.1.2011.5.14.6.1.1.40 | ColumnhwOpticsModuleUserEeprom | read-only | current | Optics module user EEPROM information. |
| 1.3.6.1.4.1.2011.5.14.6.2 | TablehwOpticsModuleTransceiverTable | not-accessible | current | This table used for querying the information about the optical transceiver of an Ethernet port. The index of this table is ifindex. |
| 1.3.6.1.4.1.2011.5.14.6.2.1 | RowhwOpticsModuleTransceiverEntry | not-accessible | current | This table used for querying the information about the optical transceiver of an Ethernet port. The index of this entry is ifindex. |
| 1.3.6.1.4.1.2011.5.14.6.2.1.1 | ColumnhwOpticsMDInfinibandComplianceCodes | read-only | current | Infiniband transceiver type. Options: 1. sx(1) -infiniband transceiver type is sx 2. lx(2) -infiniband transceiver type is lx 3. copperActive(3) -infiniband tr… |
| 1.3.6.1.4.1.2011.5.14.6.2.1.2 | ColumnhwOpticsMDSONETcomplianceCodes | read-only | current | SONET transceiver type. Options: 1. oC48LongReach(1) -SONET transceiver type is oC48LongReach 2. oC48IntermediateReach(2) -SONET transceiver type is oC48Interm… |
| 1.3.6.1.4.1.2011.5.14.6.2.1.3 | ColumnhwOpticsMDGEComplianceCodes | read-only | current | Ethernet transceiver type. Options: 1. en1000BASET(1) -Ethernet transceiver type is 1000BASE-T 2. en1000BASECX(2) -Ethernet transceiver type is 1000BASE-CX 3. … |
| 1.3.6.1.4.1.2011.5.14.6.2.1.4 | ColumnhwOpticsMDLinkLength | read-only | current | Fibre Channel link length. Options: 1. veryLongDistance(1) -fibre channel link length is veryLongDistance 2. shortDistance(2) -fibre channel link length is sho… |
| 1.3.6.1.4.1.2011.5.14.6.2.1.5 | ColumnhwOpticsMDTransmitterTechnology | read-only | current | Fibre Channel transmitter technology. Options: 1. longwaveLaser(1) -fibre channel transmitter technology is longwaveLaser 2. electricalInterenclosure(2) -fibre… |
| 1.3.6.1.4.1.2011.5.14.6.2.1.6 | ColumnhwOpticsMDTransmissionMedia | read-only | current | Fibre Channel transmission media. Options: 1. twinAxialPair(1) -fibre channel transmission media is twinAxialPair 2. shieldedTwistedPair(2) -fibre channel tran… |
| 1.3.6.1.4.1.2011.5.14.6.2.1.7 | ColumnhwOpticsMDSpeed | read-only | current | Fibre Channel speed. Options: 1. speed400MBytesPerSec(1) -fibre channel speed is 400 MBits/s 2. speed200MBytesPerSec(2) -fibre channel speed is 200 MBits/s 3. … |
| 1.3.6.1.4.1.2011.5.14.6.2.1.8 | ColumnhwOpticsMDTransceiverRemote | read-only | current | Indicates the operation is performed on a remote optical module. Options: 1. remote(1) -the operation is performed on a remote optical module 2. invalid(-1) -i… |
| 1.3.6.1.4.1.2011.5.14.6.2.1.9 | ColumnhwOpticsMDHuaweiPartNumber | read-only | current | Indicate the part number of a optical module provided by Huawei. |
| 1.3.6.1.4.1.2011.5.14.6.3 | Tablehw10GEOpticsModuleInformationTable | not-accessible | current | Indicates the 10GE optical module information table of an Ethernet port. It is used for querying the information about the 10GE optical module of an Ethernet p… |
| 1.3.6.1.4.1.2011.5.14.6.3.1 | Rowhw10GEOpticsModuleInformationEntry | not-accessible | current | Indicates the 10GE optical module information table of an Ethernet port. It is used for querying the information about the 10GE optical module of an Ethernet p… |
| 1.3.6.1.4.1.2011.5.14.6.3.1.1 | Columnhw10GEOpticsMDIdentifier | read-only | current | Indicate the identifier of 10GE optical module. Options: 1. unknown(0) -unknown identifier of 10GE optical module 2. gbic(1) -the identifier of 10GE optical mo… |
| 1.3.6.1.4.1.2011.5.14.6.3.1.2 | Columnhw10GEOpticsMDExtCLEICode | read-only | current | Extended identifier: CLEI Options: 1. nonExtCLEICode(0) -no CLEI code present in Table 02h 2. extCLEICode(1) -CLEI code present in Table 02h 3. invalid(-1) -in… |
| 1.3.6.1.4.1.2011.5.14.6.3.1.3 | Columnhw10GEOpticsMDExtTXRefClock | read-only | current | Extended identifier: TX Ref Clock Options: 1. nonExtTXRefClock(0) -tx Ref Clock Input Not Required 2. extTXRefClock(1) -tx Ref Clock Input Required 3. invalid(… |
| 1.3.6.1.4.1.2011.5.14.6.3.1.4 | Columnhw10GEOpticsMDExtCDRFunc | read-only | current | Extended identifier: CDR function Options: 1. nonExtCDRFunc(0) -no CDR version of XFP 2. extCDRFunc(1) -module with CDR function 3. invalid(-1) -invalid value |
| 1.3.6.1.4.1.2011.5.14.6.3.1.5 | Columnhw10GEOpticsMDExtPowerLevel | read-only | current | Extended identifier: Power Level Options: 1. extPowerLevel1(0) -power Level 1 Module (1.5 W max. power dissipation.) 2. extPowerLevel2(1) -power Level 2 Module… |
| 1.3.6.1.4.1.2011.5.14.6.3.1.6 | Columnhw10GEOpticsMDConnector | read-only | current | Indicate the type of 10GE optical module connector. Options: 1. unknown(0) -unknown the type of 10GE optical module connector 2. sc(1) -the type of 10GE optica… |
| 1.3.6.1.4.1.2011.5.14.6.3.1.7 | Columnhw10GEOpticsMDEthComplianceBaseEW | read-only | current | Indicate 10GBASE-EW support or not. Options: 1. nonEthComplianceBaseEW(0) -not support 10GBASE-EW 2. ethComplianceBaseEW(1) -support 10GBASE-EW |
| 1.3.6.1.4.1.2011.5.14.6.3.1.8 | Columnhw10GEOpticsMDEthComplianceBaseLW | read-only | current | Indicate 10GBASE-LW support or not. Options: 1. nonEthComplianceBaseLW(0) -not support 10GBASE-LW 2. ethComplianceBaseLW(1) -support 10GBASE-LW |
| 1.3.6.1.4.1.2011.5.14.6.3.1.9 | Columnhw10GEOpticsMDEthComplianceBaseSW | read-only | current | Indicate 10GBASE-SW support or not. Options: 1. nonEthComplianceBaseSW(0) -not support 10GBASE-SW 2. ethComplianceBaseSW(1) -support 10GBASE-SW |
| 1.3.6.1.4.1.2011.5.14.6.3.1.10 | Columnhw10GEOpticsMDEthComplianceBaseLRM | read-only | current | Indicate 10GBASE-LRM support or not. Options: 1. nonEthComplianceBaseLRM(0) -not support 10GBASE-LRM 2. ethComplianceBaseLRM(1) -support 10GBASE-LRM |
| 1.3.6.1.4.1.2011.5.14.6.3.1.11 | Columnhw10GEOpticsMDEthComplianceBaseER | read-only | current | Indicate 10GBASE-ER support or not. Options: 1. nonEthComplianceBaseER(0) -not support 10GBASE-ER 2. ethComplianceBaseER(1) -support 10GBASE-ER |
| 1.3.6.1.4.1.2011.5.14.6.3.1.12 | Columnhw10GEOpticsMDEthComplianceBaseLR | read-only | current | Indicate 10GBASE-LR support or not. Options: 1. nonEthComplianceBaseLR(0) -not support 10GBASE-LR 2. ethComplianceBaseLR(1) -support 10GBASE-LR |
| 1.3.6.1.4.1.2011.5.14.6.3.1.13 | Columnhw10GEOpticsMDEthComplianceBaseSR | read-only | current | Indicate 10GBASE-SR support or not. Options: 1. nonEthComplianceBaseSR(0) -not support 10GBASE-SR 2. ethComplianceBaseSR(1) -support 10GBASE-SR |
| 1.3.6.1.4.1.2011.5.14.6.3.1.14 | Columnhw10GEOpticsMDFibreCompliance | read-only | current | Indicate 10 Gigabit Fibre Channel Compliance type. Options: 1. fibreComplianceInter1300FP(16) -intermediate Reach 1300 nm FP 2. fibreComplianceExtended1550(32)… |
| 1.3.6.1.4.1.2011.5.14.6.3.1.15 | Columnhw10GEOpticsMDLowerSpeedLink | read-only | current | Indicate Lower Speed Links type. Options: 1. lowerSpeedLinkOC48LR(2) -lower speed links type is OC48LR 2. lowerSpeedLinkOC48IR(4) -lower speed links type is OC… |
| 1.3.6.1.4.1.2011.5.14.6.3.1.16 | Columnhw10GEOpticsMDSONETSDHCodesI64point5 | read-only | current | Indicate SONET/SDH Codes I-64.5 support or not. Options: 1. notSupport(0) -not Support I-64.5 2. support(1) -support I-64.5 |
| 1.3.6.1.4.1.2011.5.14.6.3.1.17 | Columnhw10GEOpticsMDSONETSDHCodesI64point3 | read-only | current | Indicate SONET/SDH Codes I-64.3 support or not. Options: 1. notSupport(0) -not Support I-64.3 2. support(1) -support I-64.3 |
| 1.3.6.1.4.1.2011.5.14.6.3.1.18 | Columnhw10GEOpticsMDSONETSDHCodesI64point2 | read-only | current | Indicate SONET/SDH Codes I-64.2 support or not. Options: 1. notSupport(0) -not Support I-64.2 2. support(1) -support I-64.2 |
| 1.3.6.1.4.1.2011.5.14.6.3.1.19 | Columnhw10GEOpticsMDSONETSDHCodesI64point2r | read-only | current | Indicate SONET/SDH Codes I-64.2r support or not. Options: 1. notSupport(0) -not support I-64.2r 2. support(1) -support I-64.2r |
| 1.3.6.1.4.1.2011.5.14.6.3.1.20 | Columnhw10GEOpticsMDSONETSDHCodesI64point1 | read-only | current | Indicate SONET/SDH Codes I-64.1 support or not. Options: 1. notSupport(0) -not support I-64.1 2. support(1) -support I-64.1 |
| 1.3.6.1.4.1.2011.5.14.6.3.1.21 | Columnhw10GEOpticsMDSONETSDHCodesI64point1r | read-only | current | Indicate SONET/SDH Codes I-64.1r support or not. Options: 1. notSupport(0) -not support I-64.1r 2. support(1) -support I-64.1r |
| 1.3.6.1.4.1.2011.5.14.6.3.1.22 | Columnhw10GEOpticsMDSONETSDHCodesS64point5b | read-only | current | Indicate SONET/SDH Codes S-64.5b support or not. Options: 1. notSupport(0) -not support S-64.5b 2. support(1) -support S-64.5b |
| 1.3.6.1.4.1.2011.5.14.6.3.1.23 | Columnhw10GEOpticsMDSONETSDHCodesS64point5a | read-only | current | Indicate SONET/SDH Codes S-64.5a support or not. Options: 1. notSupport(0) -not support S-64.5a 2. support(1) -support S-64.5a |
| 1.3.6.1.4.1.2011.5.14.6.3.1.24 | Columnhw10GEOpticsMDSONETSDHCodesS64point3b | read-only | current | Indicate SONET/SDH Codes S-64.3b support or not. Options: 1. notSupport(0) -not support S-64.3b 2. support(1) -support S-64.3b |
| 1.3.6.1.4.1.2011.5.14.6.3.1.25 | Columnhw10GEOpticsMDSONETSDHCodesS64point3a | read-only | current | Indicate SONET/SDH Codes S-64.3a support or not. Options: 1. notSupport(0) -not support S-64.3a 2. support(1) -support S-64.3a |
| 1.3.6.1.4.1.2011.5.14.6.3.1.26 | Columnhw10GEOpticsMDSONETSDHCodesS64point2b | read-only | current | Indicate SONET/SDH Codes S-64.2b support or not. Options: 1. notSupport(0) -not support S-64.2b 2. support(1) -support S-64.2b |
| 1.3.6.1.4.1.2011.5.14.6.3.1.27 | Columnhw10GEOpticsMDSONETSDHCodesS64point2a | read-only | current | Indicate SONET/SDH Codes S-64.2a support or not. Options: 1. notSupport(0) -not support S-64.2a 2. support(1) -support S-64.2a |
| 1.3.6.1.4.1.2011.5.14.6.3.1.28 | Columnhw10GEOpticsMDSONETSDHCodesS64point1 | read-only | current | Indicate SONET/SDH Codes S-64.1 support or not. Options: 1. notSupport(0) -not support S-64.1 2. support(1) -support S-64.1 |
| 1.3.6.1.4.1.2011.5.14.6.3.1.29 | Columnhw10GEOpticsMDSONETSDHCodesG959P1L1 | read-only | current | Indicate SONET/SDH Codes G.959.1 P1L1-2D2 support or not. Options: 1. notSupport(0) -not support G.959.1 P1L1-2D2 2. support(1) -support G.959.1 P1L1-2D2 |
| 1.3.6.1.4.1.2011.5.14.6.3.1.30 | Columnhw10GEOpticsMDSONETSDHCodesL64point3 | read-only | current | Indicate SONET/SDH Codes L-64.3 support or not. Options: 1. notSupport(0) -not support L-64.3 2. support(1) -support L-64.3 |
| 1.3.6.1.4.1.2011.5.14.6.3.1.31 | Columnhw10GEOpticsMDSONETSDHCodesL64point2c | read-only | current | Indicate SONET/SDH Codes L-64.2c support or not. Options: 1. notSupport(0) -not support L-64.2c 2. support(1) -support L-64.2c |
| 1.3.6.1.4.1.2011.5.14.6.3.1.32 | Columnhw10GEOpticsMDSONETSDHCodesL64point2b | read-only | current | Indicate SONET/SDH Codes L-64.2b support or not. Options: 1. notSupport(0) -not support L-64.2b 2. support(1) -support L-64.2b |
| 1.3.6.1.4.1.2011.5.14.6.3.1.33 | Columnhw10GEOpticsMDSONETSDHCodesL64point2a | read-only | current | Indicate SONET/SDH Codes L-64.2a support or not. Options: 1. notSupport(0) -not support L-64.2a 2. support(1) -support L-64.2a |
| 1.3.6.1.4.1.2011.5.14.6.3.1.34 | Columnhw10GEOpticsMDSONETSDHCodesL64point1 | read-only | current | Indicate SONET/SDH Codes L-64.1 support or not. Options: 1. notSupport(0) -not support L-64.1 2. support(1) -support L-64.1 |
| 1.3.6.1.4.1.2011.5.14.6.3.1.35 | Columnhw10GEOpticsMDSONETSDHCodesV64point3 | read-only | current | Indicate SONET/SDH Codes V-64.3 support or not. Options: 1. notSupport(0) -not support V-64.3 2. support(1) -support V-64.3 |
| 1.3.6.1.4.1.2011.5.14.6.3.1.36 | Columnhw10GEOpticsMDSONETSDHCodesV64point2b | read-only | current | Indicate SONET/SDH Codes V-64.2b support or not. Options: 1. notSupport(0) -not support V-64.2b 2. support(1) -support V-64.2b |
| 1.3.6.1.4.1.2011.5.14.6.3.1.37 | Columnhw10GEOpticsMDSONETSDHCodesV64point2a | read-only | current | Indicate SONET/SDH Codes V-64.2a support or not. Options: 1. notSupport(0) -not support V-64.2a 2. support(1) -support V-64.2a |
| 1.3.6.1.4.1.2011.5.14.6.3.1.38 | Columnhw10GEOpticsMDEncodingRZ | read-only | current | Indicate encoding mechanism RZ support or not. Options: 1. nonEncodingRZ(0) -not support RZ 2. encodingRZ(1) -support RZ |
| 1.3.6.1.4.1.2011.5.14.6.3.1.39 | Columnhw10GEOpticsMDEncodingNRZ | read-only | current | Indicate encoding mechanism NRZ support or not. Options: 1. nonEncodingNRZ(0) -not support NRZ 2. encodingNRZ(1) -support NRZ |
| 1.3.6.1.4.1.2011.5.14.6.3.1.40 | Columnhw10GEOpticsMDEncodingSONET | read-only | current | Indicate encoding mechanism SONET support or not. Options: 1. nonEncodingSONET(0) -not support SONET 2. encodingSONET(1) -support SONET |
| 1.3.6.1.4.1.2011.5.14.6.3.1.41 | Columnhw10GEOpticsMDEncoding8B10B | read-only | current | Indicate encoding mechanism 8B10B support or not. Options: 1. nonEncoding8B10B(0) -not support 8B10B 2. encoding8B10B(1) -support 8B10B |
| 1.3.6.1.4.1.2011.5.14.6.3.1.42 | Columnhw10GEOpticsMDEncoding64B | read-only | current | Indicate encoding mechanism 64B/66B support or not. Options: 1. nonEncoding64B(0) -not support 64B/66B 2. encoding64B(1) -support 64B/66B |
| 1.3.6.1.4.1.2011.5.14.6.3.1.43 | Columnhw10GEOpticsMDBrMin | read-only | current | Minimum bit rate. Unit: 100 MBits/s |
| 1.3.6.1.4.1.2011.5.14.6.3.1.44 | Columnhw10GEOpticsMDBrMax | read-only | current | Maximum bit rate. Unit: 100 MBits/s |
| 1.3.6.1.4.1.2011.5.14.6.3.1.45 | Columnhw10GEOpticsMDSupportLenSMF | read-only | current | Indicate the link length that is supported by the transceiver with the applicable standards using Single-mode Fiber. |
| 1.3.6.1.4.1.2011.5.14.6.3.1.46 | Columnhw10GEOpticsMDSupportLenE50um | read-only | current | Indicate the link length that is supported by the transceiver with the applicable standards using 2000MHz*km (850nm) extended bandwidth 50 micron core multimod… |
| 1.3.6.1.4.1.2011.5.14.6.3.1.47 | Columnhw10GEOpticsMDSupportLen50um | read-only | current | This value specifies the link length that is supported by the transceiver with the applicable standards using 500MHz*km (850 and 1310nm) 50 micron core multimo… |
| 1.3.6.1.4.1.2011.5.14.6.3.1.48 | Columnhw10GEOpticsMDSupportLen62p5um | read-only | current | This value specifies the link length that is supported by the transceiver with the applicable standards using 200MHz*km (850 nm)/500 MHz*km (1310 nm) 62.5 micr… |
| 1.3.6.1.4.1.2011.5.14.6.3.1.49 | Columnhw10GEOpticsMDSupportLenCopper | read-only | current | Indicate the minimum link length that is supported by the transceiver with copper cable. Unit: 1m |
| 1.3.6.1.4.1.2011.5.14.6.3.1.50 | Columnhw10GEOpticsMDTransmitterSupport | read-only | current | Indicate the transmitter support tunable or not. Options: 1. nonTunable(0) -transmitter not support tunable 2. tunable(1) -transmitter support tunable 3. inval… |
| 1.3.6.1.4.1.2011.5.14.6.3.1.51 | Columnhw10GEOpticsMDDetector | read-only | current | Indicate the Detector is enable or not. Options: 1. nonDetector(0) -detector is disable 2. detector(1) -detector is enable 3. invalid(-1) -invalid value |
| 1.3.6.1.4.1.2011.5.14.6.3.1.52 | Columnhw10GEOpticsMDCooledTransmitterDevice | read-only | current | Indicate the Cooled transmitter is enable or not. Options: 1. nonSupport(0) -cooled transmitter is disable 2. support(1) -cooled transmitter is enable 3. inval… |
| 1.3.6.1.4.1.2011.5.14.6.3.1.53 | Columnhw10GEOpticsMDWavelengthControl | read-only | current | Indicate the wavelength control support or not. Options: 1. nonSupport(0) -wavelength control not support 2. support(1) -wavelength control support 3. invalid(… |
| 1.3.6.1.4.1.2011.5.14.6.3.1.54 | Columnhw10GEOpticsMDTransmitterTechnologySupport | read-only | current | Indicate the transmitter technology type. Options: 1. vCSEL850(0) -the transmitter technology type is vCSEL850 2. vCSEL1310(1) -the transmitter technology type… |
| 1.3.6.1.4.1.2011.5.14.6.3.1.55 | Columnhw10GEOpticsMDVendorName | read-only | current | Indicate the vendor name of a 10GE optical module. |
| 1.3.6.1.4.1.2011.5.14.6.3.1.56 | Columnhw10GEOpticsMDSupportXFIMode | read-only | current | Indicate the XFI loopback mode support or not. Options: 1. nonSupportXFIMode(0) -the XFI loopback mode not support 2. supportXFIMode(1) -the XFI loopback mode … |
| 1.3.6.1.4.1.2011.5.14.6.3.1.57 | Columnhw10GEOpticsMDSupportLinesideMode | read-only | current | Indicate the Lineside loopback mode support or not. Options: 1. nonSupportLinesideMode(0) -lineside loopback mode not support 2. supportLinesideMode(1) -linesi… |
| 1.3.6.1.4.1.2011.5.14.6.3.1.58 | Columnhw10GEOpticsMDMaxBitRateSupportedByCDR | read-only | current | Indicate which rate is supported by the CDR. Options: 1. maxBitRateSupportedByCDR11p1(1) -CDR support for 11.1 Gb/s 2. maxBitRateSupportedByCDR10p7(3) -CDR sup… |
| 1.3.6.1.4.1.2011.5.14.6.3.1.59 | Columnhw10GEOpticsMDVendorOUI | read-only | current | Indicate the vendor IEEE company ID of a 10GE optical module. |
| 1.3.6.1.4.1.2011.5.14.6.3.1.60 | Columnhw10GEOpticsMDVendorPN | read-only | current | Indicate the part number of a 10GE optical module provided by vendor. |
| 1.3.6.1.4.1.2011.5.14.6.3.1.61 | Columnhw10GEOpticsMDVendorRev | read-only | current | Indicate the revision level for part number provided by vendor. |
| 1.3.6.1.4.1.2011.5.14.6.3.1.62 | Columnhw10GEOpticsMDWavelength | read-only | current | The laser wavelength. |
| 1.3.6.1.4.1.2011.5.14.6.3.1.63 | Columnhw10GEOpticsMDWaveTolerance | read-only | current | The guaranteed +/- range of transmitter output wavelength under all normal operating conditions. |
| 1.3.6.1.4.1.2011.5.14.6.3.1.64 | Columnhw10GEOpticsMDMaxCaseTemperature | read-only | current | Maximum Case Temperature in Degrees C. |
| 1.3.6.1.4.1.2011.5.14.6.3.1.65 | Columnhw10GEOpticsMDCcbase | read-only | current | Cc_base. |
| 1.3.6.1.4.1.2011.5.14.6.3.1.66 | Columnhw10GEOpticsMDMaxDissipation | read-only | current | Maximum Power Dissipation. Max power is 8 bit value * 20 mW. |
| 1.3.6.1.4.1.2011.5.14.6.3.1.67 | Columnhw10GEOpticsMDMaxDissipationPowerDownMode | read-only | current | Maximum Total Power Dissipation in Power Down Mode. Max Power is 8 bit value * 10 mW. |
| 1.3.6.1.4.1.2011.5.14.6.3.1.68 | Columnhw10GEOpticsMDMaximum5P0VSupply | read-only | current | Maximum current required by +5V Supply. |
| 1.3.6.1.4.1.2011.5.14.6.3.1.69 | Columnhw10GEOpticsMDMaximum3P3VSupply | read-only | current | Maximum current required by +3.3V Supply. |
| 1.3.6.1.4.1.2011.5.14.6.3.1.70 | Columnhw10GEOpticsMDMaximum1P8VSupply | read-only | current | Maximum current required by +1.8V Supply. |
| 1.3.6.1.4.1.2011.5.14.6.3.1.71 | Columnhw10GEOpticsMDMaximum5P2VSupply | read-only | current | Maximum current required by -5.2V Supply. |
| 1.3.6.1.4.1.2011.5.14.6.3.1.72 | Columnhw10GEOpticsMDVendorSN | read-only | current | The serial number of a 10GE optical module provided by vendor. |
| 1.3.6.1.4.1.2011.5.14.6.3.1.73 | Columnhw10GEOpticsMDDateCode | read-only | current | The date code of a 10GE optical module. |
| 1.3.6.1.4.1.2011.5.14.6.3.1.74 | Columnhw10GEOpticsMDDiagnoMonitorPowerMeasure | read-only | current | Received power measurement type. Options: 1. supportOMA(0) -OMA 2. supportAveragePower(1) -AveragePower |
| 1.3.6.1.4.1.2011.5.14.6.3.1.75 | Columnhw10GEOpticsMDDiagnoMonitorTypeFECBER | read-only | current | Module Respond to FEC BER. Options: 1. nonSupportBER(0) -no BER Support 2. supportBER(1) -BER Support |
| 1.3.6.1.4.1.2011.5.14.6.3.1.76 | Columnhw10GEOpticsMDEnhancedOptions | read-only | current | Indicate enhanced Options. Options: 1. cmu(0) -enhanced options is cmu 2. rateSelect(2) -enhanced options is rateSelect 3. fec(4) -enhanced options is fec 4. v… |
| 1.3.6.1.4.1.2011.5.14.6.3.1.77 | Columnhw10GEOpticsMDAuxInputOne | read-only | current | Indicate which quantity is monitored by each auxiliary A/D channel one. Options: 1. auxInputType1(0) -Auxiliary monitoring not implemented 2. auxInputType2(1) … |
| 1.3.6.1.4.1.2011.5.14.6.3.1.78 | Columnhw10GEOpticsMDAuxInputTwo | read-only | current | Indicate which quantity is monitored by each auxiliary A/D channel two. Options: 1. auxInputType1(0) -Auxiliary monitoring not implemented 2. auxInputType2(1) … |
| 1.3.6.1.4.1.2011.5.14.6.3.1.79 | Columnhw10GEOpticsMDCCEXT | read-only | current | CC_EXT |
| 1.3.6.1.4.1.2011.5.14.6.3.1.80 | Columnhw10GEOpticsMDVendorSpecific | read-only | current | Vendor of 10GE Optical module specific information. |
| 1.3.6.1.4.1.2011.5.14.6.4 | TablehwOpticsDdmInformationTable | not-accessible | current | Indicates the optical module diagnose information table of an Ethernet port. It is used for querying the diagnose information about the optical module of an Et… |
| 1.3.6.1.4.1.2011.5.14.6.4.1 | RowhwOpticsDdmInformationEntry | not-accessible | current | Indicates the optical module diagnose information table of an Ethernet port. It is used for querying the diagnose information about the optical module of an Et… |
| 1.3.6.1.4.1.2011.5.14.6.4.1.1 | ColumnhwOpticsTemperature | read-only | current | Temperature. Invalid value: 2147483647, an invalid value is returned if the optical module is unavailable or is not supported. Unit: 0.000001C |
| 1.3.6.1.4.1.2011.5.14.6.4.1.2 | ColumnhwOpticsSupplyVoltage | read-only | current | Supply voltage. Invalid value: 2147483647, an invalid value is returned if the optical module is unavailable or is not supported. Unit: 0.000001V |
| 1.3.6.1.4.1.2011.5.14.6.4.1.3 | ColumnhwOpticsTxBiasCurrent | read-only | current | Transmitted bias current. Invalid value: 2147483647, an invalid value is returned if the optical module is unavailable or is not supported. Unit: 0.000001mA |
| 1.3.6.1.4.1.2011.5.14.6.4.1.4 | ColumnhwOpticsTxPower | read-only | current | Transmitted power. Invalid value: 2147483647, an invalid value is returned if the optical module is unavailable or is not supported. Unit: 0.000001dBm |
| 1.3.6.1.4.1.2011.5.14.6.4.1.5 | ColumnhwOpticsRxPower | read-only | current | Received power. Invalid value: 2147483647, an invalid value is returned if the optical module is unavailable or is not supported. Unit: 0.000001dBm |
| 1.3.6.1.4.1.2011.5.14.6.4.1.6 | ColumnhwOpticsMDDdmInfoRemote | read-only | current | Indicates the operation is performed on a remote optical module. Options: 1. remote(1) -the operation is performed on a remote optical module 2. invalid(-1) -i… |
| 1.3.6.1.4.1.2011.5.14.6.4.1.7 | ColumnhwOpticsLaserTemperature | read-only | current | Temperature of the optical laser. Invalid value: 2147483647, returned if the optical module is unavailable or not supported. Unit: 0.000001C |
| 1.3.6.1.4.1.2011.5.14.6.4.1.8 | ColumnhwOpticsWaveLength | read-only | current | Wavelength of the optical laser. Invalid value: 2147483647, returned if the optical module is unavailable or not supported. Unit: 0.01nm |
| 1.3.6.1.4.1.2011.5.14.6.4.1.9 | ColumnhwOpticsTecCurrent | read-only | current | Current of the thermoelectric cooler on the optical module. Invalid value: 2147483647, returned if the optical module is unavailable or not supported. Unit: 0.… |
| 1.3.6.1.4.1.2011.5.14.6.5 | TablehwOpticsPowerThresholdTable | not-accessible | current | Indicates the optical power threshold table of an Ethernet port. It is used for querying, setting, and clearing the optical power threshold of an Ethernet port… |
| 1.3.6.1.4.1.2011.5.14.6.5.1 | RowhwOpticsPowerThresholdEntry | not-accessible | current | Indicates the optical power threshold table of an Ethernet port. It is used for querying, setting, and clearing the optical power threshold of an Ethernet port… |
| 1.3.6.1.4.1.2011.5.14.6.5.1.1 | ColumnhwOpticsPowerTxLowerThresholdValue | read-write | current | TX optical power lower limit threshold value. Options: 1. -99000000..100000000 -valid range of optical power lower limit threshold value. 2. 2147483646 -indica… |
| 1.3.6.1.4.1.2011.5.14.6.5.1.2 | ColumnhwOpticsPowerThresholdSwitch | read-write | current | Optical power threshold value Switch. Options: 1. on(1) -set optical power threshold value 2. off(2) -clear optical power threshold value 3. invalid(-1) -inval… |
| 1.3.6.1.4.1.2011.5.14.6.5.1.3 | ColumnhwOpticsPowerTxUpperThresholdValue | read-write | current | TX optical power upper limit threshold value. 1. -99000000..100000000 -valid range of optical power upper limit threshold value. 2. 2147483646 -indication the … |
| 1.3.6.1.4.1.2011.5.14.6.5.1.4 | ColumnhwOpticsPowerRxUpperThresholdValue | read-write | current | RX optical power upper limit threshold value. 1. -99000000..100000000 -valid range of optical power upper limit threshold value. 2. 2147483646 -indication the … |
| 1.3.6.1.4.1.2011.5.14.6.5.1.5 | ColumnhwOpticsPowerRxLowerThresholdValue | read-write | current | RX optical power lower limit threshold value. 1. -99000000..100000000 -valid range of optical power lower limit threshold value. 2. 2147483646 -indication the … |
| 1.3.6.1.4.1.2011.5.14.6.5.1.6 | ColumnhwOpticsTemperatureLowerThresholdValue | read-write | current | Optical temperature lower limit threshold value. 1. -99000000..300000000 -valid range of optical temperature lower limit threshold value. 2. 2147483646 -indica… |
| 1.3.6.1.4.1.2011.5.14.6.5.1.7 | ColumnhwOpticsTemperatureUpperThresholdValue | read-write | current | Optical temperature upper limit threshold value. 1. -99000000..300000000 -valid range of optical temperature upper limit threshold value. 2. 2147483646 -indica… |
| 1.3.6.1.4.1.2011.5.14.6.5.1.8 | ColumnhwOpticsTemperatureThresholdSwitch | read-write | current | Optical temperature threshold value Switch. Options: 1. on(1) -set optical temparature threshold value 2. off(2) -clear optical temperature threshold value 3. … |
| 1.3.6.1.4.1.2011.5.14.6.5.1.9 | ColumnhwOpticsVoltageLowerThresholdValue | read-write | current | Optical voltage lower limit threshold value. 1. 0..100000000 -valid range of optical voltage lower limit threshold value. 2. 2147483646 -indication the optical… |
| 1.3.6.1.4.1.2011.5.14.6.5.1.10 | ColumnhwOpticsVoltageUpperThresholdValue | read-write | current | Optical voltage upper limit threshold value. 1. 0..100000000 -valid range of optical voltage upper limit threshold value. 2. 2147483646 -indication the optical… |
| 1.3.6.1.4.1.2011.5.14.6.5.1.11 | ColumnhwOpticsVoltageThresholdSwitch | read-write | current | Optical voltage threshold value Switch. Options: 1. on(1) -set optical voltage threshold value 2. off(2) -clear optical voltage threshold value 3. invalid(-1) … |
| 1.3.6.1.4.1.2011.5.14.6.5.1.12 | ColumnhwOpticsCurrentLowerThresholdValue | read-write | current | Optical current lower limit threshold value. 1. 0..10000000 -valid range of optical current lower limit threshold value. 2. 2147483646 -indication the optical … |
| 1.3.6.1.4.1.2011.5.14.6.5.1.13 | ColumnhwOpticsCurrentUpperThresholdValue | read-write | current | Optical current upper limit threshold value. 1. 0..10000000 -valid range of optical current upper limit threshold value. 2. 2147483646 -indication the optical … |
| 1.3.6.1.4.1.2011.5.14.6.5.1.14 | ColumnhwOpticsCurrentThresholdSwitch | read-write | current | Optical current threshold value Switch. Options: 1. on(1) -set optical current threshold value 2. off(2) -clear optical current threshold value 3. invalid(-1) … |
| 1.3.6.1.4.1.2011.5.14.6.5.1.15 | ColumnhwOpticsLaserTemperatureLowerThresholdValue | read-write | current | Lower optical laser temperature threshold. 1. -99000000..300000000 -valid range of the lower optical laser temperature threshold. 2. 2147483646 -indication the… |
| 1.3.6.1.4.1.2011.5.14.6.5.1.16 | ColumnhwOpticsLaserTemperatureUpperThresholdValue | read-write | current | Upper optical laser temperature threshold. 1. -99000000..300000000 -valid range of the upper optical laser temperature threshold. 2. 2147483646 -indication the… |
| 1.3.6.1.4.1.2011.5.14.6.5.1.17 | ColumnhwOpticsLaserTemperatureThresholdSwitch | read-write | current | Switch of optical laser temperature thresholds. Options: 1. on(1) -Set optical laser temperature thresholds. 2. off(2) -Clear optical laser temperature thresho… |
| 1.3.6.1.4.1.2011.5.14.6.5.1.18 | ColumnhwOpticsWaveLengthLowerThresholdValue | read-write | current | Lower optical laser wavelength threshold. 1. 100000..165600 -valid range of the lower optical laser wavelength threshold. 2. 2147483646 -indication the optical… |
| 1.3.6.1.4.1.2011.5.14.6.5.1.19 | ColumnhwOpticsWaveLengthUpperThresholdValue | read-write | current | Upper optical laser wavelength threshold. 1. 100000..165600 -valid range of the upper optical laser wavelength threshold. 2. 2147483646 -indication the optical… |
| 1.3.6.1.4.1.2011.5.14.6.5.1.20 | ColumnhwOpticsWaveLengthThresholdSwitch | read-write | current | Switch of optical laser wavelength thresholds. Options: 1. on(1) -Set optical laser wavelength thresholds. 2. off(2) -Clear optical laser wavelength thresholds… |
| 1.3.6.1.4.1.2011.5.14.6.5.1.21 | ColumnhwOpticsTecCurrentLowerThresholdValue | read-write | current | Lower threshold for the thermoelectric cooler current. 1. -10000000-10000000 -valid range of the lower threshold for the thermoelectric cooler current. 2. 2147… |
| 1.3.6.1.4.1.2011.5.14.6.5.1.22 | ColumnhwOpticsTecCurrentUpperThresholdValue | read-write | current | Upper threshold for the thermoelectric cooler current. 1. -10000000-10000000 -valid range of the upper threshold for the thermoelectric cooler current. 2. 2147… |
| 1.3.6.1.4.1.2011.5.14.6.5.1.23 | ColumnhwOpticsTecCurrentThresholdSwitch | read-write | current | Switch of thermoelectric cooler current thresholds. Options: 1. on(1) -Set thermoelectric cooler current thresholds. 2. off(2) -Clear thermoelectric cooler cur… |
| 1.3.6.1.4.1.2011.5.14.6.6 | NodehwOpticsModuleTraps | |||
| 1.3.6.1.4.1.2011.5.14.6.6.1 | NodehwOpticsCommonTraps | |||
| 1.3.6.1.4.1.2011.5.14.6.6.1.0 | NodehwOpticsCommonTrapsPrefix | |||
| 1.3.6.1.4.1.2011.5.14.6.6.2 | NodehwOpticsAlarmTraps | |||
| 1.3.6.1.4.1.2011.5.14.6.6.2.0 | NodehwOpticsAlarmTrapsPrefix | |||
| 1.3.6.1.4.1.2011.5.14.6.6.2.0.1 | NotificationhwOpticsTransceiverFaultyAlarmTrap | current | This trap will send when the optical transceiver is faulty. | |
| 1.3.6.1.4.1.2011.5.14.6.6.2.0.2 | NotificationhwOpticsPowerOutOfRangeAlarmTrap | current | This trap will send when the Tx power of the Ethernet optical port is out of the range. | |
| 1.3.6.1.4.1.2011.5.14.6.6.2.0.3 | NotificationhwOpticsPortTemperatureHighAlarmTrap | current | This trap will send when the temperature of the Ethernet optical port is too high. | |
| 1.3.6.1.4.1.2011.5.14.6.7 | TablehwOpticsSmartSFPExtModuleInformationTable | not-accessible | current | Indicates the extended information table of a smart SFP optical module. It is used for querying the extend information about a smart SFP optical module and set… |
| 1.3.6.1.4.1.2011.5.14.6.7.1 | RowhwOpticsSmartSFPExtModuleInformationEntry | not-accessible | current | Indicates the extended information table of a smart SFP optical module. It is used for querying the extend information about a smart SFP optical module and set… |
| 1.3.6.1.4.1.2011.5.14.6.7.1.1 | ColumnhwOpticsSmartSFPIdentifier | read-only | current | Indicates the type of a smart SFP optical module. Options: 1. smartSFPI(1) -The optical module is a smart SFP I optical module 2. smartSFPII(2) -The optical mo… |
| 1.3.6.1.4.1.2011.5.14.6.7.1.2 | ColumnhwOpticsSmartSFPProtocolVersion | read-only | current | Indicates the protocol version of a smart SFP optical module. Range: -1, 0-255. -1 is the invalid value. |
| 1.3.6.1.4.1.2011.5.14.6.7.1.3 | ColumnhwOpticsSmartSFPSSFPEnhancedOption | read-only | current | Indicates the enhanced options of a smart SFP optical module. Range: -1, 0-65535. -1 is the invalid value. |
| 1.3.6.1.4.1.2011.5.14.6.7.1.4 | ColumnhwOpticsSmartSFPPassword | read-only | current | Indicates the password of a smart SFP optical module. |
| 1.3.6.1.4.1.2011.5.14.6.7.1.5 | ColumnhwOpticsSmartSFPRemoteControllable | read-only | current | Indicates whether the remote smart SFP optical module can control the local optical module. Options: 1. disable(1) -disable, control command from remote optica… |
| 1.3.6.1.4.1.2011.5.14.6.7.1.6 | ColumnhwOpticsSmartSFPSubCarrierControl | read-only | current | Indicates sub-carrier control of a smart SFP optical module, that is, whether the local smart SFP optical module can send signals to the remote optical module.… |
| 1.3.6.1.4.1.2011.5.14.6.7.1.7 | ColumnhwOpticsSmartSFPSubCarrierlinkStatus | read-only | current | Indicates the sub-carrier status of a smart SFP optical module. Options: 1. down(1) -linked down 2. rxUp(2) -linked up in RX only 3. up(3) -linked up in both R… |
| 1.3.6.1.4.1.2011.5.14.6.7.1.8 | ColumnhwOpticsSmartSFPLocalLoopback | read-write | current | Indicates the loopback control of a local smart SFP optical module. Options: 1. noloop(1) -no loop 2. remote(2) -local outward loop back 3. local(3) -local inw… |
| 1.3.6.1.4.1.2011.5.14.6.7.1.9 | ColumnhwOpticsSmartSFPRemoteLoopback | read-write | current | Indicates the loopback control of a remote smart SFP optical module. Options: 1. noloop(1) -no loop 2. remote(2) -remote outward loop back 3. invalid(-1) -inva… |
| 1.3.6.1.4.1.2011.5.14.6.7.1.10 | ColumnhwOpticsSmartSFPDyingGaspStatus | read-write | current | Indicates the dying-gasp status of a remote smart SFP optical module. Options: 1. poweron(1) -remote normal power 2. poweroff(2) -remote Dying-Gasp asserted 3.… |
| 1.3.6.1.4.1.2011.5.14.6.7.1.11 | ColumnhwOpticsSmartSFPLocalRXOutputControl | read-write | current | Indicates the local output control of a smart SFP optical module. Options: 1. disable(1) -disable 2. enable(2) -enable 3. disableRxLos(3) -disable when LOS ass… |
| 1.3.6.1.4.1.2011.5.14.6.7.1.12 | ColumnhwOpticsSmartSFPPilottoneControl | read-write | current | Indicates control of outputting attenuation signals by a smart SFP optical module. Options: 1. disable(1) -disable 2. enable(2) -enable 3. invalid(-1) -invalid… |
| 1.3.6.1.4.1.2011.5.14.6.7.1.13 | ColumnhwOpticsSmartSFPPilottoneStatus | read-write | current | Indicates the carrier loopback detection status of a smart SFP optical module. Options: 1. noSignal(1) -no signal 2. toneDetected(2) -tone detected 3. invalid(… |
| 1.3.6.1.4.1.2011.5.14.6.7.1.14 | ColumnhwOpticsSmartSFPLoopbackdeviceloss | read-only | current | Indicates the optical attenuation of a remote loopback device. Range: -1, 0-25500. -1 is the invalid value. Unit: 0.01db |
| 1.3.6.1.4.1.2011.5.14.6.7.1.15 | ColumnhwOpticsSmartSFPRoundtripfiberloss | read-only | current | Indicates the optical attenuation of an optical path. Range: -1, 0-25500. -1 is the invalid value. Unit: 0.01db |
| 1.3.6.1.4.1.2011.5.14.6.7.1.16 | ColumnhwOpticsSmartSFPExtModuleInfoRemote | read-only | current | Indicates the operation is performed on a remote optical module. Options: 1. remote(1) -the operation is performed on a remote optical module 2. invalid(-1) -i… |
| 1.3.6.1.4.1.2011.5.14.6.8 | TablehwOpticsSmartSFPConfigTable | not-accessible | current | Indicates the configured parameter table of a smart SFP optical module. It is used for querying and setting the configured parameters of a smart SFP optical mo… |
| 1.3.6.1.4.1.2011.5.14.6.8.1 | RowhwOpticsSmartSFPConfigEntry | not-accessible | current | Indicates the configured parameter table of a smart SFP optical module. It is used for querying and setting the configured parameters of a smart SFP optical mo… |
| 1.3.6.1.4.1.2011.5.14.6.8.1.1 | ColumnhwOpticsSmartSFPIILoopOpticloss | read-write | current | Indicates the optical attenuation of a remote loopback device. Unit: 0.01db. Range: -1, 0-25500. -1 is the invalid value. Default: 14000. |
| 1.3.6.1.4.1.2011.5.14.6.9 | TablehwOpticsModuleThresholdTable | not-accessible | current | It is used for querying the default value of optical power and parameter threshold of an Ethernet port. The index of this table is ifindex. |
| 1.3.6.1.4.1.2011.5.14.6.9.1 | RowhwOpticsModuleThresholdEntry | not-accessible | current | It is used for querying the default value of optical power and parameter threshold of an Ethernet port. The index of this entry is ifindex. |
| 1.3.6.1.4.1.2011.5.14.6.9.1.1 | ColumnhwOpticsModuleThresholdTxLower | read-only | current | TX optical power lower limit threshold value. 1. 2147483647 -invalid value, an invalid value is returned if the threshold is not exist. Unit: 0.000001dBm |
| 1.3.6.1.4.1.2011.5.14.6.9.1.2 | ColumnhwOpticsModuleThresholdTxUpper | read-only | current | TX optical power upper limit threshold value. 1. 2147483647 -invalid value, an invalid value is returned if the threshold is not exist. Unit: 0.000001dBm |
| 1.3.6.1.4.1.2011.5.14.6.9.1.3 | ColumnhwOpticsModuleThresholdRxUpper | read-only | current | RX optical power upper limit threshold value. 1. 2147483647 -invalid value, an invalid value is returned if the threshold is not exist. Unit: 0.000001dBm |
| 1.3.6.1.4.1.2011.5.14.6.9.1.4 | ColumnhwOpticsModuleThresholdRxLower | read-only | current | RX optical power lower limit threshold value. 1. 2147483647 -invalid value, an invalid value is returned if the threshold is not exist. Unit: 0.000001dBm |
| 1.3.6.1.4.1.2011.5.14.6.9.1.5 | ColumnhwOpticsModuleThresholdTempLower | read-only | current | Optical temperature lower limit threshold value. 1. 2147483647 -invalid value, an invalid value is returned if the threshold is not exist. Unit: 0.000001C |
| 1.3.6.1.4.1.2011.5.14.6.9.1.6 | ColumnhwOpticsModuleThresholdTempUpper | read-only | current | Optical temperature upper limit threshold value. 1. 2147483647 -invalid value, an invalid value is returned if the threshold is not exist. Unit: 0.000001C |
| 1.3.6.1.4.1.2011.5.14.6.9.1.7 | ColumnhwOpticsModuleThresholdVoltageLower | read-only | current | Optical voltage lower limit threshold value. 1. 2147483647 -invalid value, an invalid value is returned if the threshold is not exist. Unit: 0.000001V |
| 1.3.6.1.4.1.2011.5.14.6.9.1.8 | ColumnhwOpticsModuleThresholdVoltageUpper | read-only | current | Optical voltage upper limit threshold value. 1. 2147483647 -invalid value, an invalid value is returned if the threshold is not exist. Unit: 0.000001V |
| 1.3.6.1.4.1.2011.5.14.6.9.1.9 | ColumnhwOpticsModuleThresholdCurrentLower | read-only | current | Optical current lower limit threshold value. 1. 2147483647 -invalid value, an invalid value is returned if the threshold is not exist. Unit: 0.000001A |
| 1.3.6.1.4.1.2011.5.14.6.9.1.10 | ColumnhwOpticsModuleThresholdCurrentUpper | read-only | current | Optical current upper limit threshold value. 1. 2147483647 -invalid value, an invalid value is returned if the threshold is not exist. Unit: 0.000001A |
| 1.3.6.1.4.1.2011.5.14.6.9.1.11 | ColumnhwOpticsModuleThresholdLaserTempLower | read-only | current | Lower optical laser temperature threshold. 1. 2147483647 -invalid value, an invalid value is returned if the threshold is not exist. Unit: 0.000001C |
| 1.3.6.1.4.1.2011.5.14.6.9.1.12 | ColumnhwOpticsModuleThresholdLaserTempUpper | read-only | current | Upper optical laser temperature threshold. 1. 2147483647 -invalid value, an invalid value is returned if the threshold is not exist. Unit: 0.000001C |
| 1.3.6.1.4.1.2011.5.14.6.9.1.13 | ColumnhwOpticsModuleThresholdWaveLengthLower | read-only | current | Lower optical laser wavelength threshold. 1. 2147483647 -invalid value, an invalid value is returned if the threshold is not exist. Unit: 0.01nm |
| 1.3.6.1.4.1.2011.5.14.6.9.1.14 | ColumnhwOpticsModuleThresholdWaveLengthUpper | read-only | current | Upper optical laser wavelength threshold. 1. 2147483647 -invalid value, an invalid value is returned if the threshold is not exist. Unit: 0.01nm |
| 1.3.6.1.4.1.2011.5.14.6.9.1.15 | ColumnhwOpticsModuleThresholdTecCurrentLower | read-only | current | Lower threshold for the thermoelectric cooler current. 1. 2147483647 -invalid value, an invalid value is returned if the threshold is not exist. Unit: 0.000001A |
| 1.3.6.1.4.1.2011.5.14.6.9.1.16 | ColumnhwOpticsModuleThresholdTecCurrentUpper | read-only | current | Upper threshold for the thermoelectric cooler current. 1. 2147483647 -invalid value, an invalid value is returned if the threshold is not exist. Unit: 0.000001A |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| PortList | OCTET STRING | current | Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents… |