HUAWEI-LACP-MIB
60 objects
This mib module defines the Link Aggregation Control Protocol (LACP) MIB objects. LACP is the control protocol for implementing the link aggregation in the IEEE 802.3ad standard. By using this protocol, the ports between devices are automatically aggregated, port failure detection at layer 2 is performed, line aggregation protocol control is performed, and protection switchover function is triggered.
Imported Objects
| HUAWEI-DEVICE-MIB | hwFrameIndex hwPortIndex hwSlotIndex |
| HUAWEI-MIB | huaweiMgmt |
| IEEE8023-LAG-MIB | dot3adAggPortPartnerOperKey dot3adAggPortPartnerOperPort dot3adAggPortPartnerOperSystemID LacpKey |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Gauge32 Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE |
| SNMPv2-TC | DisplayString MacAddress RowStatus TEXTUAL-CONVENTION TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.2011.5.102 | IdentityhwLacpExt | This mib module defines the Link Aggregation Control Protocol (LACP) MIB objects. LACP is the control protocol for implementing the link aggregation in the IEE… | ||
| 1.3.6.1.4.1.2011.5.102.1 | NodehwLacpMibObjects | |||
| 1.3.6.1.4.1.2011.5.102.1.1 | TablehwAggLinkTable | not-accessible | current | Describes the configuration of static LAGs. The index of this table is hwAggLinkNumber. |
| 1.3.6.1.4.1.2011.5.102.1.1.1 | RowhwAggLinkEntry | not-accessible | current | Describes the configuration of static LAGs. The index of this entry is hwAggLinkNumber. |
| 1.3.6.1.4.1.2011.5.102.1.1.1.1 | ColumnhwAggLinkNumber | accessible-for-notify | current | Indicates the index of each LAG. The index uniquely identifies a LAG and equals the ifindex value of the master port. |
| 1.3.6.1.4.1.2011.5.102.1.1.1.2 | ColumnhwAggLinkName | read-create | current | The name of an aggregation group |
| 1.3.6.1.4.1.2011.5.102.1.1.1.3 | ColumnhwAggLinkMode | read-create | current | Type of aggregation. 1 => Manual aggregation, no LACP 2 => Membership specified by user, LACP is used to validate 3 => Completely dynamic aggregation detected … |
| 1.3.6.1.4.1.2011.5.102.1.1.1.4 | ColumnhwAggLinkPortList | read-create | current | List of ports in this AL, by bridge port number. If the type is manual or static, you can update this list to your hearts content. If, however, the AL is dynam… |
| 1.3.6.1.4.1.2011.5.102.1.1.1.5 | ColumnhwAggLinkState | read-create | current | RowStatus |
| 1.3.6.1.4.1.2011.5.102.1.1.1.6 | ColumnhwAggPortListSelectedPorts | read-only | current | A PortList of physical ports that have selected to this aggregator, but which have not yet attached. |
| 1.3.6.1.4.1.2011.5.102.1.1.1.7 | ColumnhwAggPortListSamePartnerPorts | read-only | current | PortList of physical ports that the same Actor SystemID and partner systemID as this aggregator, but have differing actor and partner keys. |
| 1.3.6.1.4.1.2011.5.102.1.1.1.8 | ColumnhwAggLinkShareType | read-only | current | Indicates the load sharing type of links. Options: 1. loadSharing(1) -indicates sharing the link load 2. nonLoadSharing(2) -indicates not sharing the link load |
| 1.3.6.1.4.1.2011.5.102.1.1.1.9 | ColumnhwAggLinkProtectType | read-only | current | Indicates the protection type of links. Options: 1. backupProtect(1) -indicates the backup aggregation protection 2. nonBackupProtect(2) -indicates the non-bac… |
| 1.3.6.1.4.1.2011.5.102.1.1.1.10 | ColumnhwAggLinkSelectPorts | read-only | current | Indicates the number of selected ports in the LAG. |
| 1.3.6.1.4.1.2011.5.102.1.1.1.11 | ColumnhwAggLinkUnselectPorts | read-only | current | Indicates the number of unselected ports in the LAG. |
| 1.3.6.1.4.1.2011.5.102.1.1.1.12 | ColumnhwAggLinkMasterPort | read-only | current | Indicates the ifindex of the master port in the LAG. |
| 1.3.6.1.4.1.2011.5.102.1.1.1.13 | ColumnhwAggLinkPreemptDelayTime | read-write | current | Indicates the value of preempt delay time. The unit is second. Default:0 |
| 1.3.6.1.4.1.2011.5.102.1.2 | TablehwAggPortTable | not-accessible | current | Describes the configuration of the ports in static LAGs. The index of this table is hwAggPortIndex. |
| 1.3.6.1.4.1.2011.5.102.1.2.1 | RowhwAggPortEntry | not-accessible | current | Describes the configuration of the ports in static LAGs. The index of this entry is hwAggPortIndex. |
| 1.3.6.1.4.1.2011.5.102.1.2.1.1 | ColumnhwAggPortIndex | not-accessible | current | Indicates the index of the port in a LAG. The index uniquely identifies a port in a LAG and equals the ifIndex value of the port. |
| 1.3.6.1.4.1.2011.5.102.1.2.1.2 | ColumnhwAggPortNotAttachedReason | read-write | current | Indicates why this port is selected for an aggregator but not attached, in-use for this aggregator. resources are already being used. configuration is not appr… |
| 1.3.6.1.4.1.2011.5.102.1.2.1.3 | ColumnhwAggPortLacpState | read-write | current | Control lacp enable or disable |
| 1.3.6.1.4.1.2011.5.102.1.2.1.4 | ColumnhwAggPortNotAttachedString | read-write | current | Indicates why this port is selected for an aggregator but not attached |
| 1.3.6.1.4.1.2011.5.102.1.2.1.5 | ColumnhwAggPortRole | read-only | current | Indicates the port role. Options: 1. selected(1) -indicates the port is selected 2. unselected(2) -indicates the port is not selected |
| 1.3.6.1.4.1.2011.5.102.1.2.1.6 | ColumnhwAggPortType | read-only | current | Indicates the port type. Options: 1. mastPort(1) -indicates the port is a primary port 2. nonMastPort(2) -indicates the port is a secondary port |
| 1.3.6.1.4.1.2011.5.102.1.2.1.7 | ColumnhwAggPortStatus | read-only | current | Indicates the port status. Options: 1. forwarding(1) -indicates packets on the port can be forwarded 2. block(2) -indicates the port is blocked |
| 1.3.6.1.4.1.2011.5.102.1.3 | ScalarhwAggResourceAllocationValue | read-only | current | The priority value calculated to decide which aggregations have first call on the load-sharing aggregation resources in the hardware. DEFVAL { 0 } |
| 1.3.6.1.4.1.2011.5.102.1.4 | ScalarhwAggShortPeriod | read-write | current | Indicates the value of the short period for link aggregation. Range: 0-10 Default: 1 Unit: second When set to 0, the short period is restored to the default va… |
| 1.3.6.1.4.1.2011.5.102.1.5 | ScalarhwAggLongPeriod | read-write | current | Indicates the value of the long period for link aggregation. Range: 0, 20-40 Default: 30 Unit: second When set to 0, the long period is restored to the default… |
| 1.3.6.1.4.1.2011.5.102.1.6 | ScalarhwAggPreempt | read-write | current | This object enables/disables LACP priority preemption function. Options: 1. enable(1) -indicates the LACP priority preemption function is enable 2. disable(2) … |
| 1.3.6.1.4.1.2011.5.102.1.7 | ScalarhwLacpTimeoutMode | read-write | current | Indicates the timeout period for receiving LACP packets. Options: 1. fast(1) -indicates short timeout period for receiving LACP packets 2. slow(2) -indicates l… |
| 1.3.6.1.4.1.2011.5.102.2 | NodehwLacpMibNotifications | |||
| 1.3.6.1.4.1.2011.5.102.2.1 | NotificationhwAggSpeedChangedNotification | current | This event will be triggered whenever an aggregation changes its speed. | |
| 1.3.6.1.4.1.2011.5.102.2.4 | NotificationhwAggPortInactiveNotification | current | This event will be triggered whenever any port in aggregator is made inactive | |
| 1.3.6.1.4.1.2011.5.102.4 | NodehwLacpMibConformance | |||
| 1.3.6.1.4.1.2011.5.102.4.1 | NodehwLacpMibCompliances | |||
| 1.3.6.1.4.1.2011.5.102.4.1.1 | CompliancehwLacpMibCompliance | current | The compliance statement for SNMP entities which implement the Lacp MIB. | |
| 1.3.6.1.4.1.2011.5.102.4.2 | NodehwLacpMibGroup | |||
| 1.3.6.1.4.1.2011.5.102.4.2.1 | GrouphwLacpMibObjectGroup | current | The collection of objects which are used to represent Lacp objects. | |
| 1.3.6.1.4.1.2011.5.102.4.2.2 | GrouphwLacpMibNotificationGroup | current | The collection of objects which are used to represent notifications. | |
| 1.3.6.1.4.1.2011.5.102.5 | NodehwLacpTrapsVbOids | |||
| 1.3.6.1.4.1.2011.5.102.5.1 | ScalarhwOldUpLinkMACAddress | accessible-for-notify | current | Indicates the old up link mac-address. |
| 1.3.6.1.4.1.2011.5.102.5.2 | ScalarhwNewUpLinkMACAddress | accessible-for-notify | current | Indicates the new up link mac-address. |
| 1.3.6.1.4.1.2011.5.102.5.3 | ScalarhwAggLinkGroupID | accessible-for-notify | current | Indicates the aggregation link group ID. |
| 1.3.6.1.4.1.2011.5.102.5.4 | ScalarhwLacpFiberConnectErrorOperSystemID | accessible-for-notify | current | The system MAC Address of equipment which fiber cross-connected to LACP partner system by mistake. This fiber cross-connected error is detected by comparing th… |
| 1.3.6.1.4.1.2011.5.102.5.5 | ScalarhwLacpFiberConnectErrorOperPort | accessible-for-notify | current | The operational port number of equipment which fiber cross-connected to LACP partner system by mistake. This fiber cross-connected error is detected by compari… |
| 1.3.6.1.4.1.2011.5.102.5.6 | ScalarhwLacpFiberConnectErrorOperKey | accessible-for-notify | current | The operational key of equipment which fiber cross-connected to LACP partner system by mistake. This fiber cross-connected error is detected by comparing the p… |
| 1.3.6.1.4.1.2011.5.102.6 | NodehwLacpTraps | |||
| 1.3.6.1.4.1.2011.5.102.6.1 | NodehwLacpAlarmTraps | |||
| 1.3.6.1.4.1.2011.5.102.6.1.0 | NodehwLacpAlarmTrapsPrefix | |||
| 1.3.6.1.4.1.2011.5.102.6.1.0.1 | NotificationhwLacpPortLinkFaultTrap | current | The SNMP trap that is generated when LACP link is faulty. | |
| 1.3.6.1.4.1.2011.5.102.6.1.0.2 | NotificationhwLacpPortLinkRecoverTrap | current | The SNMP trap that is generated when the port receives the LACP packet normally. | |
| 1.3.6.1.4.1.2011.5.102.6.1.0.3 | NotificationhwLacpGroupMacChangeTrap | current | The SNMP trap that is generated when LACP up link switch over. | |
| 1.3.6.1.4.1.2011.5.102.6.1.0.4 | NotificationhwLacpPortStateForwardingTrap | current | The SNMP trap that is generated when a port turns into forwarding state from other state. | |
| 1.3.6.1.4.1.2011.5.102.6.1.0.5 | NotificationhwLacpPortStateDiscardingTrap | current | The SNMP trap that is generated when a port turns into discarding state from forwarding state. | |
| 1.3.6.1.4.1.2011.5.102.6.1.0.6 | NotificationhwLacpFiberConnectErrorTrap | current | The SNMP trap that is generated when a fiber connect error occurs. | |
| 1.3.6.1.4.1.2011.5.102.6.2 | NodehwLacpCommonTraps | |||
| 1.3.6.1.4.1.2011.5.102.6.2.0 | NodehwLacpCommonTrapsPrefix | |||
| 1.3.6.1.4.1.2011.5.102.6.2.0.1 | NotificationhwLacpPortStateForwarding | current | The SNMP trap that is generated when a port turns into forwarding state from other state. | |
| 1.3.6.1.4.1.2011.5.102.6.2.0.2 | NotificationhwLacpPortStateDiscarding | current | The SNMP trap that is generated when a port turns into discarding state from forwarding state. |