HUAWEI-SNMP-NOTIFICATION-MIB
187 objects
This MIB object is used to describe the interfaces of sending the host notifications (including the alarm and event), and configurations of the log, syslog and trap.
Imported Objects
| HUAWEI-DEVICE-MIB | hwFrameIndex hwNewDeviceIpAddr hwOldDeviceIpAddr hwPortIndex hwSlotIndex hwSysIpAddr hwSysVersion |
| HUAWEI-MIB | huaweiUtility |
| HUAWEI-TC-MIB | hwAlarmSn hwTrapType |
| IF-MIB | ifIndex |
| SNMP-TARGET-MIB | snmpTargetAddrName snmpTargetAddrTAddress |
| SNMPv2-SMI | Counter32 Integer32 IpAddress MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DateAndTime RowStatus TEXTUAL-CONVENTION TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.2011.6.30 | IdentityhwSyntrap | not-accessible | This MIB object is used to describe the interfaces of sending the host notifications (including the alarm and event), and configurations of the log, syslog and… | |
| 1.3.6.1.4.1.2011.6.30.1 | NodehwAlarmSynObjects | |||
| 1.3.6.1.4.1.2011.6.30.1.1 | ScalarhwAlarmBufferMinSn | read-only | current | Minimum serial number of the alarm buffered in the current system. |
| 1.3.6.1.4.1.2011.6.30.1.2 | ScalarhwAlarmBufferMaxSn | read-only | current | Maximum serial number of the alarm buffered in the current system. |
| 1.3.6.1.4.1.2011.6.30.1.3 | ScalarhwAlarmSynBeginSn | read-write | current | Starting serial number of the alarm trap whose synchronization is initiated by the NMS. The value ranges from hwAlarmBufferMinSn to hwAlarmBufferMaxSn. When th… |
| 1.3.6.1.4.1.2011.6.30.1.4 | ScalarhwAlarmSynEndSn | read-write | current | Ending serial number of the alarm trap whose synchronization is initiated by the NMS. The value ranges from hwAlarmBufferMinSn to hwAlarmBufferMaxSn. When the … |
| 1.3.6.1.4.1.2011.6.30.1.5 | ScalarhwAlarmSynAdminStatus | read-write | current | When the alarm whose synchronization is initiated by the NMS, one of the following methods can be used: Options: 1. other(1) -other. 2. stop(2) -stop. 3. inter… |
| 1.3.6.1.4.1.2011.6.30.1.7 | TablehwAlarmSendTable | not-accessible | current | Alarm reporting control table. It is used to control by alarm ID whether to report the trap generated corresponding to an alarm to the trap host. The index of … |
| 1.3.6.1.4.1.2011.6.30.1.7.1 | RowhwAlarmSendEntry | not-accessible | current | Alarm reporting control table. It is used to control by alarm ID whether to report the trap generated corresponding to an alarm to the trap host. The index of … |
| 1.3.6.1.4.1.2011.6.30.1.7.1.1 | ColumnhwAlarmIndex | not-accessible | current | Index of the alarm reporting control table. The index value is the alarm ID. |
| 1.3.6.1.4.1.2011.6.30.1.7.1.2 | ColumnhwAlarmSendSwitch | read-write | current | Control function of whether to report the trap generated corresponding to an alarm to the trap host. Options: 1. on(1) -indicates that the trap generated corre… |
| 1.3.6.1.4.1.2011.6.30.1.8 | TablehwMaintainSendTable | not-accessible | obsolete | Currently, the table is not supported. The index of this table is hwMaintainIndex. |
| 1.3.6.1.4.1.2011.6.30.1.8.1 | RowhwMaintainSendEntry | not-accessible | obsolete | Currently, the table is not supported. The index of this entry is hwMaintainIndex. |
| 1.3.6.1.4.1.2011.6.30.1.8.1.1 | ColumnhwMaintainIndex | not-accessible | obsolete | Currently, the object is not supported. |
| 1.3.6.1.4.1.2011.6.30.1.8.1.2 | ColumnhwMaintainSendSwitch | read-write | obsolete | Currently, the object is not supported. Options: 1.on(1) -on. 2.off(2)-off. |
| 1.3.6.1.4.1.2011.6.30.2 | NodehwSynMibTrap | |||
| 1.3.6.1.4.1.2011.6.30.2.1 | NodehwSynTrapOid | |||
| 1.3.6.1.4.1.2011.6.30.2.2 | NodehwSynTrapsDefine | |||
| 1.3.6.1.4.1.2011.6.30.2.2.0 | NodehwSynTraps | |||
| 1.3.6.1.4.1.2011.6.30.2.2.0.1 | NotificationhwSynAlarm | obsolete | Currently, the object is not supported. This trap is reported when syn operation from NMS. | |
| 1.3.6.1.4.1.2011.6.30.3 | NodehwRtuTrapRestrain | |||
| 1.3.6.1.4.1.2011.6.30.3.1 | ScalarhwRtuTrapRestrainSwitch | read-write | current | RTU trap restrain switch status. Options: 1. enable(1) -RTU trap restrain switch is enable. 2. disable(2) -RTU trap restrain switch is disable. |
| 1.3.6.1.4.1.2011.6.30.3.2 | ScalarhwRtuResetAllConfigID | read-write | current | Set operation used to reset all RTU's configID. Options: 1. unknown(1) -means don't known if RTU is administrable, setting all configID to '-1'. 2. administrab… |
| 1.3.6.1.4.1.2011.6.30.3.11 | TablehwRtuConfigIDTable | not-accessible | current | RTU ConfigID table.The index of this table is ifIndex. Currently, the object is not supported. |
| 1.3.6.1.4.1.2011.6.30.3.11.1 | RowhwRtuConfigIDEntry | not-accessible | current | RTU ConfigID table.The index of this entry is ifIndex. Currently, the object is not supported. |
| 1.3.6.1.4.1.2011.6.30.3.11.1.1 | ColumnhwRtuConfigID | read-write | current | The ConfigID of RTU. Currently, the object is not supported. |
| 1.3.6.1.4.1.2011.6.30.4 | NodehwAlarm | |||
| 1.3.6.1.4.1.2011.6.30.4.2 | ScalarhwAlarmStatPeriod | read-write | current | Alarm statistics period. Range: 1-8760 Default: 24 Unit: hour |
| 1.3.6.1.4.1.2011.6.30.4.3 | ScalarhwAlarmStatSave | read-write | obsolete | Operation of saving the alarm statistical information. The statistical information is saved to the flash memory according to the preset period. Options: 1. sav… |
| 1.3.6.1.4.1.2011.6.30.4.4 | ScalarhwAlarmStatCurPeriodStartTime | read-only | current | The alarm statistics function is to automatically collect the alarm statistics according to the preset period and this object is used to query the start time o… |
| 1.3.6.1.4.1.2011.6.30.4.6 | TablehwAlarmStatInfoTable | not-accessible | obsolete | Function of querying the alarm statistical information. It is used to query the count of the alarm occurring in the statistical period. The index of this table… |
| 1.3.6.1.4.1.2011.6.30.4.6.1 | RowhwAlarmStatInfoEntry | not-accessible | obsolete | Function of querying the alarm statistical information. It is used to query the count of the alarm occurring in the statistical period. The index of this entry… |
| 1.3.6.1.4.1.2011.6.30.4.6.1.1 | ColumnhwAlarmStatID | read-only | obsolete | Index of operation table hwAlarmStatInfoTable. It is used to indicate the ID of the alarm to be queried. |
| 1.3.6.1.4.1.2011.6.30.4.6.1.2 | ColumnhwAlarmStatCurrentNum | read-only | obsolete | Query the count of the alarm occurring in the current statistical period by index. |
| 1.3.6.1.4.1.2011.6.30.4.6.1.3 | ColumnhwAlarmStatLastNum | read-only | obsolete | Query the count of the alarm occurring in the previous statistical period by index. |
| 1.3.6.1.4.1.2011.6.30.5 | NodehwSyslogOutput | |||
| 1.3.6.1.4.1.2011.6.30.5.1 | TablehwSyslogOutputTable | not-accessible | current | Levels of the all the logs supported by the current syslog. The index of this table is hwSyslogLevelIndex. hwSyslogLevelIndex is used to describe of the level … |
| 1.3.6.1.4.1.2011.6.30.5.1.1 | RowhwSyslogOutputEntry | not-accessible | current | Levels of the all the logs supported by the current syslog. The index of this entry is hwSyslogLevelIndex. hwSyslogLevelIndex is used to describe of the level … |
| 1.3.6.1.4.1.2011.6.30.5.1.1.1 | ColumnhwSyslogLevelIndex | read-only | current | Description of the level of the output syslog information. Currently, the syslog supports eight data types. Options: 1. emergency(1) -indicates that system is … |
| 1.3.6.1.4.1.2011.6.30.5.1.1.2 | ColumnhwSyslogOutputOperStatus | read-write | current | The output status of the syslog information. Options: 1. unoutput(1) -indicates that the syslog information is not output to the local PC or server. 2. output(… |
| 1.3.6.1.4.1.2011.6.30.5.2 | ScalarhwSyslogFacility | read-write | current | Description of the facility of the output syslog information. Options: 1. local0(1) -indicates that the syslog facility is local0. 2. local1(2) -indicates that… |
| 1.3.6.1.4.1.2011.6.30.5.3 | ScalarhwSyslogSeverity | read-write | current | Description of the severity of the output syslog information. Options: 1. emergency(1) -indicates that system is unusable. 2. alert(2) -indicates that action m… |
| 1.3.6.1.4.1.2011.6.30.5.4 | TablehwSysloglogFacilityTable | not-accessible | current | Log facility of the current syslog. The index of this entry is hwSyslogLogType. hwSyslogLogType is used to describe the type of the syslog. |
| 1.3.6.1.4.1.2011.6.30.5.4.1 | RowhwSysloglogFacilityEntry | not-accessible | current | Log facility of the current syslog. The index of this entry is hwSyslogLogType. hwSyslogLogType is used to describe the type of the syslog. |
| 1.3.6.1.4.1.2011.6.30.5.4.1.1 | ColumnhwSyslogLogType | not-accessible | current | Description of the type of the output syslog information. Options: 1. log(1) -indicates that the syslog type is log. 2. alarmEvent(2) -indicates that the syslo… |
| 1.3.6.1.4.1.2011.6.30.5.4.1.2 | ColumnhwSyslogLogFacility | read-write | current | Description of the facility of the output syslog information. Options: 1. local0(1) -indicates that the syslog facility is local0. 2. local1(2) -indicates that… |
| 1.3.6.1.4.1.2011.6.30.5.4.1.3 | ColumnhwSyslogLogSeverity | read-write | current | Description of the severity of the output syslog information. Options: 1. emergency(1) -indicates that system is unusable. 2. alert(2) -indicates that action m… |
| 1.3.6.1.4.1.2011.6.30.6 | NodehwEventCtrl | |||
| 1.3.6.1.4.1.2011.6.30.6.1 | TablehwEventCtrlTable | not-accessible | current | Event control table. It is used to set the event level through the NMS or query the event list supported in the system. The information that can be queried inc… |
| 1.3.6.1.4.1.2011.6.30.6.1.1 | RowhwEventCtrlEntry | not-accessible | current | Event control table. It is used to set the event level through the NMS or query the event list supported in the system. The information that can be queried inc… |
| 1.3.6.1.4.1.2011.6.30.6.1.1.1 | ColumnhwEventID | not-accessible | current | Index object of the event control table. The index value is the event ID and the information about the event control table is obtained according to the current… |
| 1.3.6.1.4.1.2011.6.30.6.1.1.2 | ColumnhwEventName | read-only | current | Event name. It is used to briefly describe the event trigged by the system. |
| 1.3.6.1.4.1.2011.6.30.6.1.1.3 | ColumnhwEventClass | read-only | current | Event class. Currently, the system supports two event classes: Options: 1. running(1) -indicates the running event, such as the prompt displayed during the loa… |
| 1.3.6.1.4.1.2011.6.30.6.1.1.4 | ColumnhwEventLevel | read-write | current | Reference the description of SeverityLevel. |
| 1.3.6.1.4.1.2011.6.30.6.1.1.5 | ColumnhwEventDefaultLevel | read-only | current | Reference the description of SeverityLevel. |
| 1.3.6.1.4.1.2011.6.30.6.1.1.6 | ColumnhwEventType | read-only | current | Event type. Currently, the system supports five event types. Options: 1. communication(1) -indicates the communication event. 2. service(2) -indicates the serv… |
| 1.3.6.1.4.1.2011.6.30.6.1.1.7 | ColumnhwEventStatCurrNum | read-only | current | Count of the event occurring in the current period. |
| 1.3.6.1.4.1.2011.6.30.6.1.1.8 | ColumnhwEventStatPrevNum | read-only | current | Count of the event occurring in the previous period. |
| 1.3.6.1.4.1.2011.6.30.6.1.1.9 | ColumnhwEventAdminStatus | read-write | current | Event management status. Currently, the system supports two states. Options: 1. init(1) -During the setting operation, you can change only the event that is in… |
| 1.3.6.1.4.1.2011.6.30.6.1.1.10 | ColumnhwEventConditionEffect | read-only | current | Event Effect. It is used to describe the Service effect of the event and is classified into two types. Options: 1. standingcondition(1) -indicates a condition … |
| 1.3.6.1.4.1.2011.6.30.7 | NodehwAlarmCtrl | |||
| 1.3.6.1.4.1.2011.6.30.7.1 | TablehwAlarmCtrlTable | not-accessible | current | Alarm control table. It is used to set the alarm level through the NMS or query the alarm list supported in the system. The information that can be queried inc… |
| 1.3.6.1.4.1.2011.6.30.7.1.1 | RowhwAlarmCtrlEntry | not-accessible | current | Alarm control table. It is used to set the alarm level through the NMS or query the alarm list supported in the system. The information that can be queried inc… |
| 1.3.6.1.4.1.2011.6.30.7.1.1.1 | ColumnhwAlarmID | not-accessible | current | Index object of the alarm control table. The index value is the alarm ID and the information about the alarm control table is obtained according to the current… |
| 1.3.6.1.4.1.2011.6.30.7.1.1.2 | ColumnhwAlarmName | read-only | current | Alarm name. It is used to briefly describe the alarm triggered by the system. |
| 1.3.6.1.4.1.2011.6.30.7.1.1.3 | ColumnhwAlarmClass | read-only | current | Alarm class. Currently, the system supports two alarm classes. Options: 1. faultalarm(1) -indicates the fault alarm. 2. restorealarm(2) -indicates the restore … |
| 1.3.6.1.4.1.2011.6.30.7.1.1.4 | ColumnhwAlarmLevel | read-write | current | Reference the description of SeverityLevel. |
| 1.3.6.1.4.1.2011.6.30.7.1.1.5 | ColumnhwAlarmDefaultLevel | read-only | current | Reference the description of SeverityLevel. |
| 1.3.6.1.4.1.2011.6.30.7.1.1.6 | ColumnhwAlarmType | read-only | current | Alarm type. It is used to describe the major cause of the alarm and is classified into five types. Options: 1. communication(1) -indicates the communication al… |
| 1.3.6.1.4.1.2011.6.30.7.1.1.7 | ColumnhwAlarmStatCurrNum | read-only | current | Count of the alarm occurring in the current period. |
| 1.3.6.1.4.1.2011.6.30.7.1.1.8 | ColumnhwAlarmStatPrevNum | read-only | current | Count of the alarm occurring in the previous period. |
| 1.3.6.1.4.1.2011.6.30.7.1.1.9 | ColumnhwAlarmAdminStatus | read-write | current | Alarm management status. Options: 1. init(1) -The default status is init(1). 2. conversion(2) -If an alarm needs to be converted into an event, perform the set… |
| 1.3.6.1.4.1.2011.6.30.7.1.1.10 | ColumnhwAlarmServiceEffect | read-write | current | Alarm Service effect status. It is used to describe the Service effect of the alarm and is classified into two types. Options: 1. nonserviceaffect(1) -indicate… |
| 1.3.6.1.4.1.2011.6.30.8 | NodehwAlarmRecordClear | |||
| 1.3.6.1.4.1.2011.6.30.8.1 | TablehwAlarmRecordClearTable | not-accessible | current | Alarm clear table. It is used to clear the active alarm by specified serial number through the NMS. The alarm refers to the alarm whose recovery alarm is not g… |
| 1.3.6.1.4.1.2011.6.30.8.1.1 | RowhwAlarmRecordClearEntry | not-accessible | current | Alarm clear table. It is used to clear the active alarm by specified serial number through the NMS. The alarm refers to the alarm whose recovery alarm is not g… |
| 1.3.6.1.4.1.2011.6.30.8.1.1.1 | ColumnhwAlarmRecordSn | not-accessible | current | Index of the alarm or event that is not recovered and to be cleared. The index value is the serial number of the alarm or event. The serial number is saved on … |
| 1.3.6.1.4.1.2011.6.30.8.1.1.2 | ColumnhwAlarmRecordAdminStatus | read-write | current | Recorded management status of the alarm. Options: 1. clear(1) -indicates that the fault alarm is cleared. 2. exist(2) -indicates that the fault alarm exists. |
| 1.3.6.1.4.1.2011.6.30.8.2 | ScalarhwAlarmRecordClearOperate | read-create | current | Serial number list of the active alarm to be cleared. |
| 1.3.6.1.4.1.2011.6.30.9 | NodehwNotifyFilter | |||
| 1.3.6.1.4.1.2011.6.30.9.1 | TablehwNotifyFilterTable | not-accessible | current | Filter table of the alarm, event and trap. It is used to set the filter condition of the alarm, event and trap through the NMS. The indexes of this table are h… |
| 1.3.6.1.4.1.2011.6.30.9.1.1 | RowhwNotifyFilterEntry | not-accessible | current | Filter table of the alarm, event and trap. It is used to set the filter condition of the alarm, event and trap through the NMS. The indexes of this entry are h… |
| 1.3.6.1.4.1.2011.6.30.9.1.1.1 | ColumnhwNotifyFilterObject | not-accessible | current | Description of all the filter objects supported by hwNotifyFilterTable. Options: 1. event(1) -indicates that the object to be filtered is the event. 2. alarm(2… |
| 1.3.6.1.4.1.2011.6.30.9.1.1.2 | ColumnhwNotifyFilterType | not-accessible | current | Description of the filter type. Currently, the system supports five filter types. Options: 1. system(1) -indicates that the object is filtered by network eleme… |
| 1.3.6.1.4.1.2011.6.30.9.1.1.3 | ColumnhwNotifyFilterCondition | not-accessible | current | Detailed condition of filtering the alarm. The range is determined by different alarm types as follows: When the type of the object to be filtered is system(1)… |
| 1.3.6.1.4.1.2011.6.30.9.1.1.4 | ColumnhwNotifyFilterRowStatus | read-create | current | The status of this conceptual row. createAndGo(4) is supplied to create a new instance of a conceptual row. destroy(6) is supplied to delete the instances asso… |
| 1.3.6.1.4.1.2011.6.30.9.10 | NodehwAlarmJitterProof | |||
| 1.3.6.1.4.1.2011.6.30.9.10.1 | ScalarhwAlarmJitterProofSwitch | read-write | current | Alarm jitter-proof function. Through this function, the alarm trap is reported to the NMS after a period that can be set. The default period is 10s and the ran… |
| 1.3.6.1.4.1.2011.6.30.9.10.2 | ScalarhwAlarmJitterProofInterval | read-write | current | Alarm jitter-proof interval. Interval of the alarm jitter-proof. Range: 1-60 Default: 10 Unit: second DEFVAL { 10 } |
| 1.3.6.1.4.1.2011.6.30.9.11 | TablehwNotifySubTable | not-accessible | obsolete | Alarm shielding table. It is used to set the condition of shielding the alarm. The index of this table is hwNotifySubHostAddress, which is the IP address of a … |
| 1.3.6.1.4.1.2011.6.30.9.11.1 | RowhwNotifySubEntry | not-accessible | obsolete | Alarm shielding table. It is used to set the condition of shielding the alarm. The index of this entry is hwNotifySubHostAddress, which is the IP address of a … |
| 1.3.6.1.4.1.2011.6.30.9.11.1.1 | ColumnhwNotifySubHostAddress | not-accessible | obsolete | IP address of the target host for which all the traps generated for the alarms are shielded. |
| 1.3.6.1.4.1.2011.6.30.9.11.1.2 | ColumnhwNotifySubAdminStatus | read-write | obsolete | Status of alarm shielding. Only two states are supported, namely, received and shielded. Options: 1. enable(1) -indicates that the alarm is received. 2. disabl… |
| 1.3.6.1.4.1.2011.6.30.9.11.1.3 | ColumnhwNotifySubContentList | read-write | obsolete | ID list of the alarm or event to be shielded. It is all or the ID list (the IDs are separated with comma). All indicates all the alarms or events. |
| 1.3.6.1.4.1.2011.6.30.9.12 | TablehwNotifyFilterExtTable | not-accessible | current | Filter extended table of the alarm, event and trap. It is used to set the filter condition of the alarm, event and trap through the NMS. The indexes of this ta… |
| 1.3.6.1.4.1.2011.6.30.9.12.1 | RowhwNotifyFilterExtEntry | not-accessible | current | Filter extended table of the alarm, event and trap. It is used to set the filter condition of the alarm, event and trap through the NMS. The indexes of this en… |
| 1.3.6.1.4.1.2011.6.30.9.12.1.1 | ColumnhwNotifyFilterExtObject | not-accessible | current | Description of all the filter objects supported by hwNotifyFilterExtTable. Options: 1. event(1) -indicates that the object to be filtered is the event. 2. alar… |
| 1.3.6.1.4.1.2011.6.30.9.12.1.2 | ColumnhwNotifyFilterExtType | not-accessible | current | Description of the filter type. Currently, the system supports five filter types. Options: 1. system(1) -indicates that the object is filtered by network eleme… |
| 1.3.6.1.4.1.2011.6.30.9.12.1.3 | ColumnhwNotifyFilterExtCondition | not-accessible | current | Detailed condition of filtering the alarm. It used 1-7 byte to describe the value, and every byte is issued as a decimal numeral. The range is determined by di… |
| 1.3.6.1.4.1.2011.6.30.9.12.1.4 | ColumnhwNotifyFilterExtRowStatus | read-create | current | The status of this conceptual row. createAndGo(4) is supplied to create a new instance of a conceptual row. destroy(6) is supplied to delete the instances asso… |
| 1.3.6.1.4.1.2011.6.30.10 | NodehwTrapFlowCtrl | |||
| 1.3.6.1.4.1.2011.6.30.10.1 | ScalarhwTrapFlowCtrlSwitch | read-write | current | Trap traffic control. In certain cases, the alarm module receives the alarm reported by the service module, processes the alarm and then reports the alarm to t… |
| 1.3.6.1.4.1.2011.6.30.11 | NodehwTrapSyn | |||
| 1.3.6.1.4.1.2011.6.30.11.1 | TablehwTrapSynTable | not-accessible | current | Trap synchronization table. The trap synchronization function is used to send the trap buffered in the system to the trap host in a file or in the synchronizat… |
| 1.3.6.1.4.1.2011.6.30.11.1.1 | RowhwTrapSynEntry | not-accessible | current | Trap synchronization table. The trap synchronization function is used to send the trap buffered in the system to the trap host in a file or in the synchronizat… |
| 1.3.6.1.4.1.2011.6.30.11.1.1.1 | ColumnhwTrapSynType | accessible-for-notify | current | Trap synchronization types. Options: 1. trap(1) -indicates that all the traps are synchronized. 2. alarm(2) -indicates that only the alarm trap is synchronized… |
| 1.3.6.1.4.1.2011.6.30.11.1.1.2 | ColumnhwTrapBufferMinSn | read-only | current | Minimum serial number of the trap in the trap buffer area. |
| 1.3.6.1.4.1.2011.6.30.11.1.1.3 | ColumnhwTrapBufferMaxSn | read-only | current | Maximum serial number of the trap in the trap buffer area. |
| 1.3.6.1.4.1.2011.6.30.11.1.1.4 | ColumnhwTrapSynBeginSn | read-write | current | Starting serial number of the trap that is synchronized. The value is the serial number of the trap in the trap buffer area and can be obtained through hwTrapB… |
| 1.3.6.1.4.1.2011.6.30.11.1.1.5 | ColumnhwTrapSynEndSn | read-write | current | Ending serial number of trap that is synchronized. The value is the serial number of the trap in the trap buffer area and can be obtained through hwTrapBufferM… |
| 1.3.6.1.4.1.2011.6.30.11.1.1.6 | ColumnhwTrapSynAdminStatus | read-write | current | Trap synchronization management status. Options: 1. other(1) -other. 2. stop(2) -stop. 3. interval(3) -indicates the traps with the serial numbers in the range… |
| 1.3.6.1.4.1.2011.6.30.11.2 | ScalarhwTrapTypeSynSwitch | read-write | current | The switch of all types of info for trap synchronization. Function of the trap synchronization. It is controlled by the bit. The issued value is ULONG and is c… |
| 1.3.6.1.4.1.2011.6.30.11.3 | ScalarhwTrapSynActiveAlarmList | read-write | current | Serial number list of the active alarm to be synchronized to NMS. |
| 1.3.6.1.4.1.2011.6.30.12 | NodehwAlarmExpSignal | |||
| 1.3.6.1.4.1.2011.6.30.12.1 | TablehwAlarmExpCtrlTable | not-accessible | current | Alarm output control table. It is used to query and configure whether the alarm signal is output through the external alarm interface. The index of this table … |
| 1.3.6.1.4.1.2011.6.30.12.1.1 | RowhwAlarmExpCtrlEntry | not-accessible | current | Alarm output control table. It is used to query and configure whether the alarm signal is output through the external alarm interface. The index of this entry … |
| 1.3.6.1.4.1.2011.6.30.12.1.1.1 | ColumnhwAlarmExpID | not-accessible | current | Index of hwAlarmExpCtrlTable. It is used to configure whether a specified alarm is output. In the configuration, the fault alarms refer to all the fault alarms… |
| 1.3.6.1.4.1.2011.6.30.12.1.1.2 | ColumnhwAlarmExpSign | read-write | current | Flag that indicates whether the alarm is output through the external alarm interface. The values are as follows: Options: 1. disable(1) -indicates that the ala… |
| 1.3.6.1.4.1.2011.6.30.12.2 | ScalarhwClrAlarmExpSignal | read-write | current | It is used to clear the alarm output signal. After the alarm output signal is cleared, the recovery notification is sent to the external alarm interface and th… |
| 1.3.6.1.4.1.2011.6.30.13 | NodehwLogSyn | |||
| 1.3.6.1.4.1.2011.6.30.13.1 | TablehwLogSynTable | not-accessible | current | Log synchronization table. It is used to query the minimum and maximum serial numbers of the logs that can be synchronized and set the condition of synchronizi… |
| 1.3.6.1.4.1.2011.6.30.13.1.1 | RowhwLogSynEntry | not-accessible | current | Log synchronization table. It is used to query the minimum and maximum serial numbers of the logs that can be synchronized and set the condition of synchronizi… |
| 1.3.6.1.4.1.2011.6.30.13.1.1.1 | ColumnhwLogSynType | not-accessible | current | Type of the log that is synchronized. Currently, the logs are classified into two types. Options: 1. operating(1) -indicates the operating log. 2. security(2) … |
| 1.3.6.1.4.1.2011.6.30.13.1.1.2 | ColumnhwLogMinSn | read-only | current | Minimum serial number of the log that can be synchronized currently. |
| 1.3.6.1.4.1.2011.6.30.13.1.1.3 | ColumnhwLogMaxSn | read-only | current | Maximum serial number of the log that can be synchronized currently. |
| 1.3.6.1.4.1.2011.6.30.13.1.1.4 | ColumnhwLogSynBeginSn | read-write | current | Starting index of the log that is synchronized. The value ranges from hwLogMinSn to hwLogMaxSn. The hwLogSynBeginSn value of -1 indicates there is no log synch… |
| 1.3.6.1.4.1.2011.6.30.13.1.1.5 | ColumnhwLogSynEndSn | read-write | current | Ending index of the log that is synchronized. The value ranges from hwLogMinSn to hwLogMaxSn and must be larger than hwLogSynBeginSn. The hwLogSynEndSn value o… |
| 1.3.6.1.4.1.2011.6.30.13.1.1.6 | ColumnhwLogSynAdminStatus | read-write | current | The synchronizing administration. Options: 1.nosynmode(-1)-indicates the default status in the system. 2.interval(3) -indicates that the host should send all t… |
| 1.3.6.1.4.1.2011.6.30.14 | NodehwLogHost | |||
| 1.3.6.1.4.1.2011.6.30.14.1 | TablehwLogHostTable | not-accessible | deprecated | Querying the status of the log host configured in the current system. The index of this table is hwLogHostIP. |
| 1.3.6.1.4.1.2011.6.30.14.1.1 | RowhwLogHostEntry | not-accessible | deprecated | Querying the status of the log host configured in the current system. The index of this entry is hwLogHostIP. |
| 1.3.6.1.4.1.2011.6.30.14.1.1.1 | ColumnhwLogHostIP | not-accessible | deprecated | IP address of the log host. It is used to obtain the host status by IP address of the log host. |
| 1.3.6.1.4.1.2011.6.30.14.1.1.2 | ColumnhwLogHostConfigStatus | read-only | deprecated | Obtained status of the log host. Options: 1. configed(1) -indicates that the log host is configured. 2. unconfiged(2) -indicates that the log host is not confi… |
| 1.3.6.1.4.1.2011.6.30.14.2 | TablehwSyslogHostTable | not-accessible | current | Syslog host table. It is used to set attribute of syslog host in the current system. The index of this table is hwSyslogHostName. |
| 1.3.6.1.4.1.2011.6.30.14.2.1 | RowhwSyslogHostEntry | not-accessible | current | Syslog host table. It is used to set attribute of syslog host in the current system. The index of this table is hwSyslogHostName. |
| 1.3.6.1.4.1.2011.6.30.14.2.1.1 | ColumnhwSyslogHostName | not-accessible | current | Syslog host name,a kind of string parameter. Index of hwSyslogHostTable. |
| 1.3.6.1.4.1.2011.6.30.14.2.1.2 | ColumnhwSyslogHostInetAddressType | read-write | current | Obtained version of internet address. Options: 1. ipv4(1) -indicates that the internet address version is IPv4. 2. ipv6(2) -indicates that the internet address… |
| 1.3.6.1.4.1.2011.6.30.14.2.1.3 | ColumnhwSyslogHostInetAddress | read-write | current | IP address of the syslog host. |
| 1.3.6.1.4.1.2011.6.30.14.2.1.4 | ColumnhwSyslogHostFacility | read-write | current | List of the syslog host facility. Through this object, the syslog host facility can be configured in batches in the format of bit-domain string. The syslog hos… |
| 1.3.6.1.4.1.2011.6.30.14.2.1.5 | ColumnhwSyslogHostRowStatus | read-create | current | The status of this conceptual row. active(1) indicates that the log host is set to the activated state. notInservice(2) indicates that the log host is set to t… |
| 1.3.6.1.4.1.2011.6.30.15 | NodehwNotificationCause | |||
| 1.3.6.1.4.1.2011.6.30.15.1 | TablehwNotificationCauseTable | not-accessible | current | Alarm or event cause querying table. It is used to query the cause description of the alarm or event by alarm or event ID. The index of this table is hwNotific… |
| 1.3.6.1.4.1.2011.6.30.15.1.1 | RowhwNotificationCauseEntry | not-accessible | current | Alarm or event cause querying table. It is used to query the cause description of the alarm or event by alarm or event ID. The index of this entry is hwNotific… |
| 1.3.6.1.4.1.2011.6.30.15.1.1.1 | ColumnhwNotificationCauseID | not-accessible | current | The index of hwNotificationCauseTable. The value is the alarm or event ID. |
| 1.3.6.1.4.1.2011.6.30.15.1.1.2 | ColumnhwNotificationCauseDesc | read-only | current | Cause description of the alarm or event. |
| 1.3.6.1.4.1.2011.6.30.16 | NodehwTrapConfig | |||
| 1.3.6.1.4.1.2011.6.30.16.1 | ScalarhwTrapFormatMode | read-write | current | The format of the reported trap. Options: 1. standard(1) -The trap message is in the standard format. 2. private(2) -The trap message is in the private format.… |
| 1.3.6.1.4.1.2011.6.30.17 | NodehwTrapVbOids | |||
| 1.3.6.1.4.1.2011.6.30.17.1 | ScalarhwTrapID | accessible-for-notify | current | Trap ID. |
| 1.3.6.1.4.1.2011.6.30.17.2 | ScalarhwTrapSN | accessible-for-notify | current | Serial number of the trap in the current system. |
| 1.3.6.1.4.1.2011.6.30.17.3 | ScalarhwTrapLevel | accessible-for-notify | current | Trap level, indicates the significance of trap. Options: 1. critical(1) -indicates the trap level is critical. 2. major(2) -indicates the trap level is major. … |
| 1.3.6.1.4.1.2011.6.30.17.4 | ScalarhwSpecificTrapType | accessible-for-notify | current | Specific trap type. Options: 1. alarm(2) -indicates the trap type is alarm trap. 2. maintain(3) -indicates the trap type is maintain trap. 3. standard(4) -indi… |
| 1.3.6.1.4.1.2011.6.30.17.5 | ScalarhwNotificationType | accessible-for-notify | current | It's value is a configuration. Options: 1. event(10) -event, NSA(non-service affecting condition). 2. adacnsa(11) -ADAC(auto detect auto clear) alarm, NSA(non-… |
| 1.3.6.1.4.1.2011.6.30.17.6 | ScalarhwUserLabel | accessible-for-notify | current | Alarm or event user label, a kind of string parameter. |
| 1.3.6.1.4.1.2011.6.30.17.7 | ScalarhwHostName | accessible-for-notify | current | Host Name,a kind of string parameter. |
| 1.3.6.1.4.1.2011.6.30.17.8 | ScalarhwLogHostMacAddress | accessible-for-notify | current | Mac Address,a kind of string parameter. |
| 1.3.6.1.4.1.2011.6.30.17.9 | ScalarhwProtocolVersion | accessible-for-notify | current | The version of SNMP protocol. 1 :indicates the SNMP v1 protocol. 2 :indicates the SNMP v2c protocol. 3 :indicates the SNMP v3 protocol. |
| 1.3.6.1.4.1.2011.6.30.17.10 | ScalarhwCommunityReadName | accessible-for-notify | current | Community read name, a kind of string parameter. |
| 1.3.6.1.4.1.2011.6.30.17.11 | ScalarhwCommunityWriteName | accessible-for-notify | current | Community write name, a kind of string parameter. |
| 1.3.6.1.4.1.2011.6.30.17.12 | ScalarhwTrapNum | accessible-for-notify | current | Number of synchronized trap messages. If it is hwAlmSynBeginTrap, the hwTrapNum value is zero. If it is hwAlmSynBeginTrap, the hwTrapNum include hwAlmSynBeginT… |
| 1.3.6.1.4.1.2011.6.30.17.13 | ScalarhwNMSIPAddr | accessible-for-notify | current | The NMS IP. |
| 1.3.6.1.4.1.2011.6.30.17.14 | ScalarhwNotificationTime | accessible-for-notify | current | Current date and time of the system. |
| 1.3.6.1.4.1.2011.6.30.17.15 | ScalarhwAlarmClearedNum | accessible-for-notify | current | Cleared active alarm number. |
| 1.3.6.1.4.1.2011.6.30.17.16 | ScalarhwAlarmClearedSnList | accessible-for-notify | current | The serial number list of cleared alarm (the serial number are separated with comma). |
| 1.3.6.1.4.1.2011.6.30.17.17 | ScalarhwTrapOperType | accessible-for-notify | current | This object indicates the operation type. Options: 1. add(1) - Add 2. modify(2) - Modify 3. delete(3) - Delete |
| 1.3.6.1.4.1.2011.6.30.18 | NodehwSnmpNotiTraps | |||
| 1.3.6.1.4.1.2011.6.30.18.1 | NodehwSnmpNotiCommonTraps | |||
| 1.3.6.1.4.1.2011.6.30.18.1.0 | NodehwSnmpNotiCommonTrapsPrefix | |||
| 1.3.6.1.4.1.2011.6.30.18.1.0.1 | NotificationhwMessageReportTrap | current | The register trap message is reported by the host to the NMS when the function of handshake between the host and the NMS is enabled. | |
| 1.3.6.1.4.1.2011.6.30.18.1.0.2 | NotificationhwShakeMessageTrap | current | Shake between host and NMS. After the function of handshake between the host and the NMS is enabled, the host periodically sends a trap message to the NMS if i… | |
| 1.3.6.1.4.1.2011.6.30.18.1.0.3 | NotificationhwAlmSynBeginTrap | current | The agent generates this trap when alarm synchronization starts. | |
| 1.3.6.1.4.1.2011.6.30.18.1.0.4 | NotificationhwAlmSynEndTrap | current | The agent generates this trap when alarm synchronization completes. | |
| 1.3.6.1.4.1.2011.6.30.18.1.0.5 | NotificationhwAlarmClearedReportTrap | current | The agent generates this trap when clear active alarm completed. | |
| 1.3.6.1.4.1.2011.6.30.18.2 | NodehwSnmpNotiAlarmTraps | |||
| 1.3.6.1.4.1.2011.6.30.18.2.0 | NodehwSnmpNotiAlarmTrapsPrefix | |||
| 1.3.6.1.4.1.2011.6.30.18.2.0.1 | NotificationhwOperationFromNmsTrap | current | This trap is reported when important operation from NMS. | |
| 1.3.6.1.4.1.2011.6.30.18.2.0.2 | NotificationhwIllegalMessageTrap | current | After the firewall is enabled, this trap message is reported when the system receives an SNMP packet whose IP address is refused by the firewall. A maximum of … | |
| 1.3.6.1.4.1.2011.6.30.18.2.0.3 | NotificationhwTargetHostDeletedTrap | current | This trap message is reported when the destination host of the trap message is deleted. | |
| 1.3.6.1.4.1.2011.6.30.19 | NodehwTrapReliability | |||
| 1.3.6.1.4.1.2011.6.30.19.1 | TablehwTrapReliabilityConfTable | not-accessible | current | Trap reliablity table. It is used to set the reliable trap through the NMS. The indexes of this table are hwTrapReliabilityTrapType and hwTrapReliabilityTrapID. |
| 1.3.6.1.4.1.2011.6.30.19.1.1 | RowhwTrapReliabilityConfEntry | not-accessible | current | Trap reliablity table. It is used to set the reliable trap through the NMS. The indexes of this entry are hwTrapReliabilityTrapType and hwTrapReliabilityTrapID. |
| 1.3.6.1.4.1.2011.6.30.19.1.1.1 | ColumnhwTrapReliabilityTrapType | not-accessible | current | Reliable trap types. Options: 1. maintain(3) -indicates the maintenance trap. 2. snmpstd(4) -indicates the standard trap. 3. topo(5) -indicates the topological… |
| 1.3.6.1.4.1.2011.6.30.19.1.1.2 | ColumnhwTrapReliabilityTrapID | not-accessible | current | Reliable trap ID, the range is 1-0xffffffff. |
| 1.3.6.1.4.1.2011.6.30.19.1.1.3 | ColumnhwTrapReliabilityConfRowStatus | read-create | current | The status of this conceptual row. createAndGo(4) is supplied to create a new instance of a conceptual row. destroy(6) is supplied to delete the instances asso… |
| 1.3.6.1.4.1.2011.6.30.19.2 | ScalarhwTrapReliablityTrapSnConfirm | read-write | current | Serial number of the trap confirmed by the NMS. When get this leaf, the value is always -1 and any serial number set will be successful. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| EventType | INTEGER { communication(1), servicequality(2), processerror(3), equipment(4), environmental(5) } | current | In ITU-T X.733: - communications alarm type: An alarm of this type is principally associated with the procedures and/or processes required to convey information from one point to another; - quality of service alarm type… |
| SeverityLevel | INTEGER { critical(1), major(2), minor(3), warning(4), cleared(5), indeterminate(6), informational(7), reliable(8), notalarmed(9), notreported(10) } | current | In ITU-T X.733: - critical: The Critical severity level indicates that a service affecting condition has occurred and an immediate corrective action is required. Such a severity can be reported, for example, when a mana… |