JUNIPER-PW-ATM-MIB
64 objects
This MIB module defines objects used for managing the atm pseudowires in Juniper products.
Imported Objects
| ATM-TC-MIB | AtmVcIdentifier AtmVpIdentifier |
| IF-MIB | InterfaceIndex |
| JUNIPER-SMI | -- Juniper Specific ATM MIB jnxMibs |
| JUNIPER-VPN-MIB | jnxVpnPwIndex jnxVpnPwVpnName jnxVpnPwVpnType |
| PerfHist-TC-MIB | PerfCurrentCount PerfIntervalCount |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Counter64 mib-2 MODULE-IDENTITY OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | RowPointer RowStatus TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.2636.3.57 | IdentityjnxPWAtmMIB | This MIB module defines objects used for managing the atm pseudowires in Juniper products. | ||
| 1.3.6.1.4.1.2636.3.57.0 | NodejnxpwAtmNotifications | |||
| 1.3.6.1.4.1.2636.3.57.1 | NodejnxpwAtmObjects | |||
| 1.3.6.1.4.1.2636.3.57.1.1 | TablejnxpwAtmCfgTable | not-accessible | current | This table specifies generic information for an ATM PW to be carried over PSN in any mode. |
| 1.3.6.1.4.1.2636.3.57.1.1.1 | RowjnxpwAtmCfgEntry | not-accessible | current | This table contains a set of parameters for the ATM PW that needs to be adapted and carried over PSN. This table is indexed by pwIndex from pwTable. An entry i… |
| 1.3.6.1.4.1.2636.3.57.1.1.1.1 | ColumnjnxpwAtmCfgMaxCellConcatenation | read-only | current | The maximum number of ATM cells that can be concatenated into one PW packet towards PSN. In non LDP or other signaling protocol environment, this object MAY be… |
| 1.3.6.1.4.1.2636.3.57.1.1.1.2 | ColumnjnxpwAtmCfgFarEndMaxCellConcatenation | read-only | current | The maximum number of ATM cells that can be concatenated into one PW packet towards PSN as reported by the far end. If no LDP in use, the object will either re… |
| 1.3.6.1.4.1.2636.3.57.1.1.1.3 | ColumnjnxpwAtmCfgTimeoutMode | read-only | current | This objects determines whether a packet can be transmitted to the PSN based on time out expiration for collecting cells or not. The actual handling of the tim… |
| 1.3.6.1.4.1.2636.3.57.1.1.1.4 | ColumnjnxpwAtmClpQosMapping | read-only | current | This Object indicates whether the CLP bits should be considered when setting the value in the Quality of Service fields of the encapsulating protocol (e.g. EXP… |
| 1.3.6.1.4.1.2636.3.57.1.2 | TablejnxpwAtmOutboundNto1Table | not-accessible | current | This table specifies the information for an ATM PW to be carried over PSN in the outbound direction. Up to N entries can be created in this table for every ent… |
| 1.3.6.1.4.1.2636.3.57.1.2.1 | RowjnxpwAtmOutboundNto1Entry | not-accessible | current | A row in this table represents an ATM PW that needs to be adapted and carried over PSN. This table is indexed by pwIndex from pwTable and the ATM interface wit… |
| 1.3.6.1.4.1.2636.3.57.1.2.1.1 | ColumnjnxpwAtmOutboundNto1AtmIf | not-accessible | current | The ATM Interface that receives cells from the ATM network. |
| 1.3.6.1.4.1.2636.3.57.1.2.1.2 | ColumnjnxpwAtmOutboundNto1Vpi | not-accessible | current | VPI value of this ATM PW. In atmTransparent(3), Vpi will be the equivalent of 0xFFFF |
| 1.3.6.1.4.1.2636.3.57.1.2.1.3 | ColumnjnxpwAtmOutboundNto1Vci | not-accessible | current | VCI value of this ATM PW. In atmTransparent(3), or VP case, the value will be the equivalent of 0xFFFF |
| 1.3.6.1.4.1.2636.3.57.1.2.1.4 | ColumnjnxpwAtmOutboundNto1RowStatus | read-only | current | This Object is used to create, modify or delete a row in this table. |
| 1.3.6.1.4.1.2636.3.57.1.2.1.5 | ColumnjnxpwAtmOutboundNto1TrafficParamDescr | read-only | current | This object represents a pointer to a ATM traffic parameter specific row in either private or standard table which will be employed while receiving cells from … |
| 1.3.6.1.4.1.2636.3.57.1.2.1.6 | ColumnjnxpwAtmOutboundNto1MappedVpi | read-only | current | The egress generated VPI value of this ATM PW. The entry is valid for PW type of atmCellNto1Vcc(9), atmCellNto1Vpc(10), atmCell1to1Vcc(12), or atmCell1to1Vpc(1… |
| 1.3.6.1.4.1.2636.3.57.1.2.1.7 | ColumnjnxpwAtmOutboundNto1MappedVci | read-only | current | The egress generated VCI value of this ATM PW. The entry is valid for PW type of atmCellNto1Vcc(9), atmCellNto1Vpc(10), atmCell1to1Vcc(12), or atmCell1to1Vpc(1… |
| 1.3.6.1.4.1.2636.3.57.1.3 | TablejnxpwAtmInboundNto1Table | not-accessible | current | This table specifies the information for an ATM PW to be carried over PSN in the Inbound direction. Up to N entries can be created in this table for every entr… |
| 1.3.6.1.4.1.2636.3.57.1.3.1 | RowjnxpwAtmInboundNto1Entry | not-accessible | current | A row in this table represents an ATM PW that needs to be adapted and carried over PSN. This table is indexed by pwIndex from pwTable and the ATM interface wit… |
| 1.3.6.1.4.1.2636.3.57.1.3.1.1 | ColumnjnxpwAtmInboundNto1AtmIf | not-accessible | current | The ATM Interface that receives cells from the ATM network. |
| 1.3.6.1.4.1.2636.3.57.1.3.1.2 | ColumnjnxpwAtmInboundNto1Vpi | not-accessible | current | VPI value of this ATM PW. In atmTransparent(3), Vpi will be the equivalent of 0xFFFF. |
| 1.3.6.1.4.1.2636.3.57.1.3.1.3 | ColumnjnxpwAtmInboundNto1Vci | not-accessible | current | VCI value of this ATM PW. In atmTransparent(3), or VP case, the value will be the equivalent of 0xFFFF |
| 1.3.6.1.4.1.2636.3.57.1.3.1.4 | ColumnjnxpwAtmInboundNto1RowStatus | read-only | current | This Object is used to create, modify or delete a row in this table. |
| 1.3.6.1.4.1.2636.3.57.1.3.1.5 | ColumnjnxpwAtmInboundNto1TrafficParamDescr | read-only | current | This object represents a pointer to a ATM traffic parameter specific row in either private or standard table which will be employed while receiving cells from … |
| 1.3.6.1.4.1.2636.3.57.1.3.1.6 | ColumnjnxpwAtmInboundNto1MappedVpi | read-only | current | The generated VPI value of this ATM PW. The entry is valid for PW type of atmCellNto1Vcc(9), atmCellNto1Vpc(10), atmCell1to1Vcc(12), or atmCell1to1Vpc(13). In … |
| 1.3.6.1.4.1.2636.3.57.1.3.1.7 | ColumnjnxpwAtmInboundNto1MappedVci | read-only | current | The generated VCI value of this ATM PW. The entry is valid for PW type of atmCellNto1Vcc(9), atmCellNto1Vpc(10), atmCell1to1Vcc(12), or atmCell1to1Vpc(13. In V… |
| 1.3.6.1.4.1.2636.3.57.1.4 | TablejnxpwAtmPerfCurrentTable | not-accessible | current | The current 15 minute interval counts are in this table. This table provides performance information per ATM PW. |
| 1.3.6.1.4.1.2636.3.57.1.4.1 | RowjnxpwAtmPerfCurrentEntry | not-accessible | current | An entry in this table is created by the agent for every pwAtmCfgTable entry. After 15 minutes, the contents of this table entry are copied to a new entry in t… |
| 1.3.6.1.4.1.2636.3.57.1.4.1.1 | ColumnjnxpwAtmPerfCurrentMissingPkts | read-only | current | Number of missing packets (as detected via control word sequence number gaps). |
| 1.3.6.1.4.1.2636.3.57.1.4.1.2 | ColumnjnxpwAtmPerfCurrentPktsReOrder | read-only | current | Number of packets detected out of sequence (via control word sequence number), but successfully re-ordered. Note: some implementations may not support this Fea… |
| 1.3.6.1.4.1.2636.3.57.1.4.1.3 | ColumnjnxpwAtmPerfCurrentPktsMisOrder | read-only | current | Number of packets detected out of order (via control word sequence numbers). |
| 1.3.6.1.4.1.2636.3.57.1.4.1.4 | ColumnjnxpwAtmPerfCurrentPktsTimeout | read-only | current | Number of packets transmitted due to timeout expiration while attempting to collect cells. |
| 1.3.6.1.4.1.2636.3.57.1.4.1.5 | ColumnjnxpwAtmPerfCurrentPktsXmit | read-only | current | Number of transmitted packets. |
| 1.3.6.1.4.1.2636.3.57.1.4.1.6 | ColumnjnxpwAtmPerfCurrentCellsDropped | read-only | current | Number of dropped cells. |
| 1.3.6.1.4.1.2636.3.57.1.4.1.7 | ColumnjnxpwAtmPerfCurrentPktsReceived | read-only | current | Number of received packets. |
| 1.3.6.1.4.1.2636.3.57.1.4.1.8 | ColumnjnxpwAtmPerfCurrentUnknownCells | read-only | current | Number of cells received from the PSN with unknown VPI or VCI values. This object is relevant only in N:1 mode. |
| 1.3.6.1.4.1.2636.3.57.1.5 | TablejnxpwAtmPerfIntervalTable | not-accessible | current | This table provides performance information per ATM PW similar to the pwAtmPerfCurrentTable above. However, these counts represent historical 15 minute interva… |
| 1.3.6.1.4.1.2636.3.57.1.5.1 | RowjnxpwAtmPerfIntervalEntry | not-accessible | current | An entry in this table is created by the agent for every pwAtmPerfCurrentEntry that is 15 minutes old. The contents of the Current entry are copied to the new … |
| 1.3.6.1.4.1.2636.3.57.1.5.1.1 | ColumnjnxpwAtmPerfIntervalNumber | not-accessible | current | A number (normally between 1 and 96 to cover a 24 hour period) which identifies the interval for which the set of statistics is available. The interval identif… |
| 1.3.6.1.4.1.2636.3.57.1.5.1.2 | ColumnjnxpwAtmPerfIntervalValidData | read-only | current | This variable indicates if the data for this interval is valid. |
| 1.3.6.1.4.1.2636.3.57.1.5.1.3 | ColumnjnxpwAtmPerfIntervalDuration | read-only | current | The duration of a particular interval in seconds, Adjustments in the system's time-of-day clock, may cause the interval to be greater or less than, the normal … |
| 1.3.6.1.4.1.2636.3.57.1.5.1.4 | ColumnjnxpwAtmPerfIntervalMissingPkts | read-only | current | Number of missing packets (as detected via control word sequence number gaps). |
| 1.3.6.1.4.1.2636.3.57.1.5.1.5 | ColumnjnxpwAtmPerfIntervalPktsReOrder | read-only | current | Number of packets detected out of sequence (via control word sequence number), but successfully re-ordered. Note: some implementations may not support this Fea… |
| 1.3.6.1.4.1.2636.3.57.1.5.1.6 | ColumnjnxpwAtmPerfIntervalPktsMisOrder | read-only | current | Number of packets detected out of order (via control word sequence numbers). |
| 1.3.6.1.4.1.2636.3.57.1.5.1.7 | ColumnjnxpwAtmPerfIntervalPktsTimeout | read-only | current | Number of packets transmitted due to timeout expiration. |
| 1.3.6.1.4.1.2636.3.57.1.5.1.8 | ColumnjnxpwAtmPerfIntervalPktsXmit | read-only | current | Number of transmitted packets. |
| 1.3.6.1.4.1.2636.3.57.1.5.1.9 | ColumnjnxpwAtmPerfIntervalCellsDropped | read-only | current | Number of dropped cells. |
| 1.3.6.1.4.1.2636.3.57.1.5.1.10 | ColumnjnxpwAtmPerfIntervalPktsReceived | read-only | current | Number of received packets. |
| 1.3.6.1.4.1.2636.3.57.1.5.1.11 | ColumnjnxpwAtmPerfIntervalUnknownCells | read-only | current | Number of cells received from the PSN with unknown VPI or VCI values. This object is relevant only in N:1 mode. |
| 1.3.6.1.4.1.2636.3.57.1.6 | TablejnxpwAtmPerf1DayIntervalTable | not-accessible | current | This table provides performance information per ATM PW similar to the pwAtmPerfIntervalTable above. However, these counters represent historical 1 day interval… |
| 1.3.6.1.4.1.2636.3.57.1.6.1 | RowjnxpwAtmPerf1DayIntervalEntry | not-accessible | current | An entry is created in this table by the agent for every entry in the pwAtmCfgTable table. |
| 1.3.6.1.4.1.2636.3.57.1.6.1.1 | ColumnjnxpwAtmPerf1DayIntervalNumber | not-accessible | current | The number of interval, where 1 indicates current day measured period and 2 and above indicate previous days respectively |
| 1.3.6.1.4.1.2636.3.57.1.6.1.2 | ColumnjnxpwAtmPerf1DayIntervalValidData | read-only | current | This object indicates if the data for this interval is valid. |
| 1.3.6.1.4.1.2636.3.57.1.6.1.3 | ColumnjnxpwAtmPerf1DayIntervalDuration | read-only | current | The duration of a particular interval in seconds, Adjustments in the system's time-of-day clock, may cause the interval to be greater or less than, the normal … |
| 1.3.6.1.4.1.2636.3.57.1.6.1.4 | ColumnjnxpwAtmPerf1DayIntervalMissingPkts | read-only | current | Number of missing packets (as detected via control word sequence number gaps). |
| 1.3.6.1.4.1.2636.3.57.1.6.1.5 | ColumnjnxpwAtmPerf1DayIntervalPktsReOrder | read-only | current | Number of packets detected out of sequence (via control word sequence number), but successfully re-ordered. Note: some implementations may not support this fea… |
| 1.3.6.1.4.1.2636.3.57.1.6.1.6 | ColumnjnxpwAtmPerf1DayIntervalPktsMisOrder | read-only | current | Number of packets detected out of order(via control word sequence numbers), and could not be re-ordered. |
| 1.3.6.1.4.1.2636.3.57.1.6.1.7 | ColumnjnxpwAtmPerf1DayIntervalPktsTimeout | read-only | current | Number of packets transmitted due to timeout expiration. |
| 1.3.6.1.4.1.2636.3.57.1.6.1.8 | ColumnjnxpwAtmPerf1DayIntervalPktsXmit | read-only | current | Number of transmitted packets. |
| 1.3.6.1.4.1.2636.3.57.1.6.1.9 | ColumnjnxpwAtmPerf1DayIntervalCellsDropped | read-only | current | Number of dropped cells. |
| 1.3.6.1.4.1.2636.3.57.1.6.1.10 | ColumnjnxpwAtmPerf1DayIntervalPktsReceived | read-only | current | Number of received packets. |
| 1.3.6.1.4.1.2636.3.57.1.6.1.11 | ColumnjnxpwAtmPerf1DayIntervalUnknownCells | read-only | current | Number of cells received from the PSN with unknown VPI or VCI value. This object is relevant only in N:1 mode. |
| 1.3.6.1.4.1.2636.3.57.2 | NodejnxpwAtmConformance |