MPLS-LDP-MIB
181 objects
This MIB contains managed object definitions for the Multiprotocol Label Switching, Label Distribution Protocol, LDP, as defined in draft-ietf-mpls-ldp-06.txt.
Imported Objects
| ATM-TC-MIB | -- AtmInterfaceType AtmVcIdentifier AtmVpIdentifier -- |
| CISCO-SMI | ciscoExperiment |
| IANA-ADDRESS-FAMILY-NUMBERS-MIB | AddressFamilyNumbers |
| IF-MIB | InterfaceIndex InterfaceIndexOrZero |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | RowPointer RowStatus StorageType TEXTUAL-CONVENTION TimeInterval TimeStamp TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.10.65 | IdentitymplsLdpMIB | This MIB contains managed object definitions for the Multiprotocol Label Switching, Label Distribution Protocol, LDP, as defined in draft-ietf-mpls-ldp-06.txt. | ||
| 1.3.6.1.4.1.9.10.65.1 | NodemplsLdpObjects | |||
| 1.3.6.1.4.1.9.10.65.1.1 | NodemplsLdpLsrObjects | |||
| 1.3.6.1.4.1.9.10.65.1.1.1 | ScalarmplsLdpLsrId | read-only | current | The LSR's Identifier. |
| 1.3.6.1.4.1.9.10.65.1.1.2 | ScalarmplsLdpLsrLabelRetentionMode | read-write | current | The LSR can be configured to use either conservative or liberal label retention mode. If the value of this object is conservative(1) then advertized label mapp… |
| 1.3.6.1.4.1.9.10.65.1.1.3 | ScalarmplsLdpLsrLoopDetectionCapable | read-only | current | A indication of whether this LSR supports loop detection. none(1) on this LSR. other(2) by a method other than those listed below. hopCount(3) Hop Count only. … |
| 1.3.6.1.4.1.9.10.65.1.2 | NodemplsLdpEntityObjects | |||
| 1.3.6.1.4.1.9.10.65.1.2.1 | ScalarmplsLdpEntityIndexNext | read-only | current | This object contains an appropriate value to be used for mplsLdpEntityIndex when creating entries in the mplsLdpEntityTable. The value 0 indicates that no unas… |
| 1.3.6.1.4.1.9.10.65.1.2.2 | TablemplsLdpEntityTable | not-accessible | current | This table contains information about the MPLS Label Distribution Protocol Entities which exist on this Label Switch Router (LSR). |
| 1.3.6.1.4.1.9.10.65.1.2.2.1 | RowmplsLdpEntityEntry | not-accessible | current | An entry in this table represents an LDP entity. An entry can be created by a network administrator or by an SNMP agent as instructed by LDP. |
| 1.3.6.1.4.1.9.10.65.1.2.2.1.1 | ColumnmplsLdpEntityLdpId | not-accessible | current | The LDP identifier. The first four octets encode an IP address assigned to the LSR, and the last two octets identify a specific label space within the LSR. |
| 1.3.6.1.4.1.9.10.65.1.2.2.1.2 | ColumnmplsLdpEntityIndex | not-accessible | current | This index is used as a secondary index to uniquely identify this row. Before creating a row in this table, the 'mplsLdpEntityIndexNext' object should be retri… |
| 1.3.6.1.4.1.9.10.65.1.2.2.1.3 | ColumnmplsLdpEntityProtocolVersion | read-create | current | The version number of the protocol. The value of 0 on a read indicates that the version of the protocol is unknown. Otherwise, the value of this object represe… |
| 1.3.6.1.4.1.9.10.65.1.2.2.1.4 | ColumnmplsLdpEntityAdminStatus | read-create | current | The administrative status of this LDP Entity. If this object is changed from 'enable' to 'disable' and this entity has already attempted to establish contact w… |
| 1.3.6.1.4.1.9.10.65.1.2.2.1.5 | ColumnmplsLdpEntityOperStatus | read-only | current | The operational status of this LDP Entity. |
| 1.3.6.1.4.1.9.10.65.1.2.2.1.6 | ColumnmplsLdpEntityWellKnownDiscoveryPort | read-create | current | The well known LDP Discovery Port. |
| 1.3.6.1.4.1.9.10.65.1.2.2.1.7 | ColumnmplsLdpEntityMaxPduLength | read-create | current | The maximum PDU Length that is sent in the Common Session Parameters of an Initialization Message. A value of 255 or less specifies the default maximum length … |
| 1.3.6.1.4.1.9.10.65.1.2.2.1.8 | ColumnmplsLdpEntityKeepAliveHoldTimer | read-create | current | The two octet value which is the proposed keep alive hold timer for this LDP Entity. |
| 1.3.6.1.4.1.9.10.65.1.2.2.1.9 | ColumnmplsLdpEntityHelloHoldTimer | read-create | current | The two octet value which is the proposed Hello hold timer for this LDP Entity. A value of 0 means use the default, which is 15 seconds for Link Hellos and 45 … |
| 1.3.6.1.4.1.9.10.65.1.2.2.1.10 | ColumnmplsLdpEntityFailedInitSessionTrapEnable | read-create | current | Indicates whether the 'mplsLdpFailedInitSessionThresholdExceeded' trap should be generated. If the value of this object is 'enabled(1)' then the trap will gene… |
| 1.3.6.1.4.1.9.10.65.1.2.2.1.11 | ColumnmplsLdpEntityFailedInitSessionThreshold | read-create | current | When attempting to establish a session with a given Peer, the given LDP Entity should send out the SNMP notification, 'mplsLdpFailedInitSessionThresholdExceede… |
| 1.3.6.1.4.1.9.10.65.1.2.2.1.12 | ColumnmplsLdpEntityLabelDistributionMethod | read-create | current | For any given LDP session, the method of label distribution must be specified. |
| 1.3.6.1.4.1.9.10.65.1.2.2.1.13 | ColumnmplsLdpEntityPVLimitMismatchTrapEnable | read-create | current | Indicates whether the 'mplsLdpPathVectorLimitMismatch' trap should be generated. If the value of this object is 'enabled(1)' then the trap will generated. If t… |
| 1.3.6.1.4.1.9.10.65.1.2.2.1.14 | ColumnmplsLdpEntityPathVectorLimit | read-create | current | If the value of this object is 0 (zero) then Loop Dection for Path Vectors is disabled. Otherwise, if this object has a value greater than zero, then Loop Dect… |
| 1.3.6.1.4.1.9.10.65.1.2.2.1.15 | ColumnmplsLdpEntityHopCountLoopDetection | read-create | current | An indication of whether loop detection based on hop count is disabled or enabled for this Entity. If this object has the value of 'disabled(0)', then loop det… |
| 1.3.6.1.4.1.9.10.65.1.2.2.1.16 | ColumnmplsLdpEntityHopCount | read-create | current | If the value of 'mplsLdpEntityHopCountLoopDetection' for this entry is 'enabled(1)', then this object represents the initial Hop Count for this Entity. If the … |
| 1.3.6.1.4.1.9.10.65.1.2.2.1.17 | ColumnmplsLdpEntityTargetedPeer | read-create | current | If this LDP entity uses targeted peer then set this to true. |
| 1.3.6.1.4.1.9.10.65.1.2.2.1.18 | ColumnmplsLdpEntityTargetedPeerAddrType | read-create | current | The type of the internetwork layer address used for the Extended Discovery. This object indicates how the value of mplsLdpEntityTargetedPeerAddr is to be inter… |
| 1.3.6.1.4.1.9.10.65.1.2.2.1.19 | ColumnmplsLdpEntityTargetedPeerAddr | read-create | current | The value of the internetwork layer address used for the Extended Discovery. |
| 1.3.6.1.4.1.9.10.65.1.2.2.1.20 | ColumnmplsLdpEntityOptionalParameters | read-create | current | Specifies the optional parameters for the LDP Initialization Message. If the value is generic(1) then no optional parameters will be sent in the LDP Initializa… |
| 1.3.6.1.4.1.9.10.65.1.2.2.1.21 | ColumnmplsLdpEntityDiscontinuityTime | read-only | current | The value of sysUpTime on the most recent occasion at which any one or more of this entity's counters suffered a discontinuity. The relevant counters are the s… |
| 1.3.6.1.4.1.9.10.65.1.2.2.1.22 | ColumnmplsLdpEntityStorageType | read-create | current | The storage type for this entry. |
| 1.3.6.1.4.1.9.10.65.1.2.2.1.23 | ColumnmplsLdpEntityRowStatus | read-create | current | An object that allows entries in this table to be created and deleted using the RowStatus convention. Once the 'mplsLdpEntityAdminStatus' object has the value … |
| 1.3.6.1.4.1.9.10.65.1.2.3 | NodemplsLdpEntityGenericObjects | |||
| 1.3.6.1.4.1.9.10.65.1.2.3.1 | TablemplsLdpEntityConfGenericTable | not-accessible | current | This table provides a way to configure Generic Labels associated with LDP entities on the LSR. |
| 1.3.6.1.4.1.9.10.65.1.2.3.1.1 | RowmplsLdpEntityConfGenericEntry | not-accessible | current | An entry in this table provides a way to configure a 'Generic Label' for LDP. An entry in the 'mplsLdpEntityTable' will only have associated entries in this Ta… |
| 1.3.6.1.4.1.9.10.65.1.2.3.1.1.1 | ColumnmplsLdpConfGenericIndex | not-accessible | current | This index is used to distinguish between multiple Generic Labels configured for the same LDP Entity. |
| 1.3.6.1.4.1.9.10.65.1.2.3.1.1.2 | ColumnmplsLdpConfGenericIfIndexOrZero | read-create | current | This value represents either the InterfaceIndex of the 'ifLayer' where this Generic Label was created, or 0 (zero). The value of zero means that the InterfaceI… |
| 1.3.6.1.4.1.9.10.65.1.2.3.1.1.3 | ColumnmplsLdpConfGenericLabel | read-create | current | The value of this object represents the Generic Label used in the Generic Label TLV. |
| 1.3.6.1.4.1.9.10.65.1.2.3.1.1.4 | ColumnmplsLdpConfGenericStorageType | read-create | current | The storage type for this entry. |
| 1.3.6.1.4.1.9.10.65.1.2.3.1.1.5 | ColumnmplsLdpConfGenericRowStatus | read-create | current | An object that allows entries in this table to be created and deleted using the RowStatus convention. NOTE: This RowStatus object should have the same value of… |
| 1.3.6.1.4.1.9.10.65.1.2.4 | NodemplsLdpEntityAtmObjects | |||
| 1.3.6.1.4.1.9.10.65.1.2.4.1 | TablemplsLdpEntityAtmParmsTable | not-accessible | current | This table contains information about the ATM specific information which could be used in the 'Optional Parameters' and other ATM specific information. |
| 1.3.6.1.4.1.9.10.65.1.2.4.1.1 | RowmplsLdpEntityAtmParmsEntry | not-accessible | current | An entry in this table represents the ATM parameters and ATM information for this LDP entity. |
| 1.3.6.1.4.1.9.10.65.1.2.4.1.1.1 | ColumnmplsLdpEntityAtmIfIndexOrZero | read-create | current | This value represents either the InterfaceIndex of the 'ifLayer' where the ATM Labels 'owned' by this entry were created, or 0 (zero). The value of zero means … |
| 1.3.6.1.4.1.9.10.65.1.2.4.1.1.2 | ColumnmplsLdpEntityAtmMergeCap | read-create | current | Denotes the Merge Capability of this Entity. |
| 1.3.6.1.4.1.9.10.65.1.2.4.1.1.3 | ColumnmplsLdpEntityAtmLabelRangeComponents | read-create | current | Number of LabelRange Components in the Initialization message. This also represents the number of entries in the mplsLdpLabelRangeComponentsTable which corresp… |
| 1.3.6.1.4.1.9.10.65.1.2.4.1.1.4 | ColumnmplsLdpEntityAtmVcDirectionality | read-create | current | If the value of this object is 'bidirectional(0)', a given VCI, within a given VPI, is used as a label for both directions independently. If the value of this … |
| 1.3.6.1.4.1.9.10.65.1.2.4.1.1.5 | ColumnmplsLdpEntityAtmLsrConnectivity | read-create | current | The peer LSR may be connected indirectly by means of an ATM VP so that the VPI values may be different on either endpoint so the label MUST be encoded entirely… |
| 1.3.6.1.4.1.9.10.65.1.2.4.1.1.6 | ColumnmplsLdpEntityDefaultControlVpi | read-create | current | The default VPI value for the non-MPLS connection. The default value of this is 0 (zero) but other values may be configured. This object allows a different val… |
| 1.3.6.1.4.1.9.10.65.1.2.4.1.1.7 | ColumnmplsLdpEntityDefaultControlVci | read-create | current | The Default VCI value for a non-MPLS connection. The default value of this is 32 but other values may be configured. This object allows a different value to be… |
| 1.3.6.1.4.1.9.10.65.1.2.4.1.1.8 | ColumnmplsLdpEntityUnlabTrafVpi | read-create | current | VPI value of the VCC supporting unlabelled traffic. This non-MPLS connection is used to carry unlabelled (IP) packets. |
| 1.3.6.1.4.1.9.10.65.1.2.4.1.1.9 | ColumnmplsLdpEntityUnlabTrafVci | read-create | current | VCI value of the VCC supporting unlabelled traffic. This non-MPLS connection is used to carry unlabelled (IP) packets. |
| 1.3.6.1.4.1.9.10.65.1.2.4.1.1.10 | ColumnmplsLdpEntityAtmStorageType | read-create | current | The storage type for this entry. |
| 1.3.6.1.4.1.9.10.65.1.2.4.1.1.11 | ColumnmplsLdpEntityAtmRowStatus | read-create | current | An object that allows entries in this table to be created and deleted using the RowStatus convention. NOTE: This RowStatus object should have the same value of… |
| 1.3.6.1.4.1.9.10.65.1.2.4.2 | TablemplsLdpEntityConfAtmLabelRangeTable | not-accessible | current | The MPLS LDP Entity Configurable ATM Label Range Table. The purpose of this table is to provide a mechanism for specifying a contiguous range of vpi's with a c… |
| 1.3.6.1.4.1.9.10.65.1.2.4.2.1 | RowmplsLdpEntityConfAtmLabelRangeEntry | not-accessible | current | A row in the LDP Entity Configurable ATM Label Range Table. One entry in this table contains information on a single range of labels represented by the configu… |
| 1.3.6.1.4.1.9.10.65.1.2.4.2.1.1 | ColumnmplsLdpEntityConfAtmLabelRangeMinimumVpi | not-accessible | current | The minimum VPI number configured for this range. |
| 1.3.6.1.4.1.9.10.65.1.2.4.2.1.2 | ColumnmplsLdpEntityConfAtmLabelRangeMinimumVci | not-accessible | current | The minimum VCI number configured for this range. |
| 1.3.6.1.4.1.9.10.65.1.2.4.2.1.3 | ColumnmplsLdpEntityConfAtmLabelRangeMaximumVpi | read-create | current | The maximum VPI number configured for this range. |
| 1.3.6.1.4.1.9.10.65.1.2.4.2.1.4 | ColumnmplsLdpEntityConfAtmLabelRangeMaximumVci | read-create | current | The maximum VCI number configured for this range. |
| 1.3.6.1.4.1.9.10.65.1.2.4.2.1.5 | ColumnmplsLdpEntityConfAtmLabelRangeStorageType | read-create | current | The storage type for this entry. |
| 1.3.6.1.4.1.9.10.65.1.2.4.2.1.6 | ColumnmplsLdpEntityConfAtmLabelRangeRowStatus | read-create | current | An object that allows entries in this table to be created and deleted using the RowStatus convention. There must exist at least one entry in this table for eve… |
| 1.3.6.1.4.1.9.10.65.1.2.5 | NodemplsLdpEntityFrameRelayObjects | |||
| 1.3.6.1.4.1.9.10.65.1.2.5.1 | TablemplsLdpEntityFrameRelayParmsTable | not-accessible | current | This table contains information about the Optional Parameters to specify what this Entity is going to specify for Frame Relay specific LDP Intialization Messag… |
| 1.3.6.1.4.1.9.10.65.1.2.5.1.1 | RowmplsLdpEntityFrameRelayParmsEntry | not-accessible | current | An entry in this table represents the Frame Relay optional parameters associated with the LDP entity. |
| 1.3.6.1.4.1.9.10.65.1.2.5.1.1.1 | ColumnmplsLdpEntityFrIfIndexOrZero | read-create | current | This value represents either the InterfaceIndex of the 'ifLayer' where the Frame Relay Labels 'owned' by this entry were created, or 0 (zero). The value of zer… |
| 1.3.6.1.4.1.9.10.65.1.2.5.1.1.2 | ColumnmplsLdpEntityFrMergeCap | read-create | current | This represents whether or not Frame Relay merge capability is supported. |
| 1.3.6.1.4.1.9.10.65.1.2.5.1.1.3 | ColumnmplsLdpEntityFrLabelRangeComponents | read-create | current | Number of LabelRange Components in the Initialization message. This also represents the number of entries in the mplsLdpEntityConfFrLabelRangeTable which corre… |
| 1.3.6.1.4.1.9.10.65.1.2.5.1.1.4 | ColumnmplsLdpEntityFrLen | read-create | current | This object specifies the DLCI bits. |
| 1.3.6.1.4.1.9.10.65.1.2.5.1.1.5 | ColumnmplsLdpEntityFrVcDirectionality | read-create | current | If the value of this object is 'bidirectional(0)', then the LSR supports the use of a given DLCI as a label for both directions independently. If the value of … |
| 1.3.6.1.4.1.9.10.65.1.2.5.1.1.6 | ColumnmplsLdpEntityFrParmsStorageType | read-create | current | The storage type for this entry. |
| 1.3.6.1.4.1.9.10.65.1.2.5.1.1.7 | ColumnmplsLdpEntityFrParmsRowStatus | read-create | current | An object that allows entries in this table to be created and deleted using the RowStatus convention. NOTE: This RowStatus object should have the same value of… |
| 1.3.6.1.4.1.9.10.65.1.2.5.2 | TablemplsLdpEntityConfFrLabelRangeTable | not-accessible | current | This table contains information about the Optional Parameters to specify what this Entity is going to specify for Frame Relay specific LDP Intialization Messag… |
| 1.3.6.1.4.1.9.10.65.1.2.5.2.1 | RowmplsLdpEntityConfFrLabelRangeEntry | not-accessible | current | An entry in this table represents the Frame Relay optional parameters associated with the LDP entity. |
| 1.3.6.1.4.1.9.10.65.1.2.5.2.1.1 | ColumnmplsLdpConfFrMinimumDlci | not-accessible | current | The lower bound which is supported. This value should be the same as that in the Frame Relay Label Range Component's Minimum DLCI field. |
| 1.3.6.1.4.1.9.10.65.1.2.5.2.1.2 | ColumnmplsLdpConfFrMaximumDlci | read-create | current | The upper bound which is supported. This value should be the same as that in the Frame Relay Label Range Component's Maximum DLCI field. |
| 1.3.6.1.4.1.9.10.65.1.2.5.2.1.3 | ColumnmplsLdpConfFrStorageType | read-create | current | The storage type for this entry. |
| 1.3.6.1.4.1.9.10.65.1.2.5.2.1.4 | ColumnmplsLdpConfFrRowStatus | read-create | current | An object that allows entries in this table to be created and deleted using the RowStatus convention. If the value of the object 'mplsLdpEntityOptionalParamete… |
| 1.3.6.1.4.1.9.10.65.1.2.6 | TablemplsLdpEntityStatsTable | not-accessible | current | This table is a read-only table which augments the mplsLdpEntityTable. The purpose of this table is to keep statistical information about the LDP Entities on t… |
| 1.3.6.1.4.1.9.10.65.1.2.6.1 | RowmplsLdpEntityStatsEntry | not-accessible | current | A row in this table contains statistical information about an LDP Entity. Some counters contained in a row are for fatal errors received during a former LDP Se… |
| 1.3.6.1.4.1.9.10.65.1.2.6.1.1 | ColumnmplsLdpAttemptedSessions | read-only | current | A count of the total attempted sessions for this LDP Entity. |
| 1.3.6.1.4.1.9.10.65.1.2.6.1.2 | ColumnmplsLdpSessionRejectedNoHelloErrors | read-only | current | A count of the Session Rejected/No Hello Error Notification Messages sent or received by this LDP Entity. |
| 1.3.6.1.4.1.9.10.65.1.2.6.1.3 | ColumnmplsLdpSessionRejectedAdvertisementErrors | read-only | current | A count of the Session Rejected/Parameters Advertisement Mode Error Notification Messages sent or received by this LDP Entity. |
| 1.3.6.1.4.1.9.10.65.1.2.6.1.4 | ColumnmplsLdpSessionRejectedMaxPduErrors | read-only | current | A count of the Session Rejected/Parameters Max Pdu Length Error Notification Messages sent or received by this LDP Entity. |
| 1.3.6.1.4.1.9.10.65.1.2.6.1.5 | ColumnmplsLdpSessionRejectedLabelRangeErrors | read-only | current | A count of the Session Rejected/Parameters Label Range Notification Notification Messages sent or received by this LDP Entity. |
| 1.3.6.1.4.1.9.10.65.1.2.6.1.6 | ColumnmplsLdpBadLdpIdentifierErrors | read-only | current | This object counts the number of Bad LDP Identifier Fatal Errors detected by the session(s) (past and present) associated with this LDP Entity. |
| 1.3.6.1.4.1.9.10.65.1.2.6.1.7 | ColumnmplsLdpBadPduLengthErrors | read-only | current | This object counts the number of Bad Pdu Length Fatal Errors detected by the session(s) (past and present) associated with this LDP Entity. |
| 1.3.6.1.4.1.9.10.65.1.2.6.1.8 | ColumnmplsLdpBadMessageLengthErrors | read-only | current | This object counts the number of Bad Message Length Fatal Errors detected by the session(s) (past and present) associated with this LDP Entity. |
| 1.3.6.1.4.1.9.10.65.1.2.6.1.9 | ColumnmplsLdpBadTlvLengthErrors | read-only | current | This object counts the number of Bad TLV Length Fatal Errors detected by the session(s) (past and present) associated with this LDP Entity. |
| 1.3.6.1.4.1.9.10.65.1.2.6.1.10 | ColumnmplsLdpMalformedTlvValueErrors | read-only | current | This object counts the number of Malformed TLV Value Fatal Errors detected by the session(s) (past and present) associated with this LDP Entity. |
| 1.3.6.1.4.1.9.10.65.1.2.6.1.11 | ColumnmplsLdpKeepAliveTimerExpiredErrors | read-only | current | This object counts the number of Session Keep Alive Timer Expired Errors detected by the session(s) (past and present) associated with this LDP Entity. |
| 1.3.6.1.4.1.9.10.65.1.2.6.1.12 | ColumnmplsLdpShutdownNotifReceived | read-only | current | This object counts the number of Shutdown Notfications received related to session(s) (past and present) associated with this LDP Entity. |
| 1.3.6.1.4.1.9.10.65.1.2.6.1.13 | ColumnmplsLdpShutdownNotifSent | read-only | current | This object counts the number of Shutdown Notfications sent related to session(s) (past and present) associated with this LDP Entity. |
| 1.3.6.1.4.1.9.10.65.1.3 | NodemplsLdpEntityPeerObjects | |||
| 1.3.6.1.4.1.9.10.65.1.3.1 | TablemplsLdpEntityPeerTable | not-accessible | current | Information about LDP peers known by Entities in the mplsLdpEntityTable. The information in this table is based on information from the Entity-Peer interaction… |
| 1.3.6.1.4.1.9.10.65.1.3.1.1 | RowmplsLdpEntityPeerEntry | not-accessible | current | Information about a single Peer which is related to an entity. |
| 1.3.6.1.4.1.9.10.65.1.3.1.1.1 | ColumnmplsLdpPeerLdpId | not-accessible | current | The LDP identifier of this LDP Peer. |
| 1.3.6.1.4.1.9.10.65.1.3.1.1.2 | ColumnmplsLdpPeerLabelDistributionMethod | read-only | current | For any given LDP session, the method of label distribution must be specified. |
| 1.3.6.1.4.1.9.10.65.1.3.1.1.3 | ColumnmplsLdpPeerLoopDetectionForPV | read-only | current | An indication of whether loop detection based on path vectors is disabled or enabled for this Peer. If this object has a value of disabled(0), then loop detect… |
| 1.3.6.1.4.1.9.10.65.1.3.1.1.4 | ColumnmplsLdpPeerPathVectorLimit | read-only | current | If the value of 'mplsLdpPeerLoopDetectionForPV' for this entry is 'enabled(1)', the this object represents that Path Vector Limit for this peer. If the value o… |
| 1.3.6.1.4.1.9.10.65.1.3.2 | NodemplsLdpHelloAdjacencyObjects | |||
| 1.3.6.1.4.1.9.10.65.1.3.2.1 | TablemplsLdpHelloAdjacencyTable | not-accessible | current | A table of Hello Adjacencies for Sessions. |
| 1.3.6.1.4.1.9.10.65.1.3.2.1.1 | RowmplsLdpHelloAdjacencyEntry | not-accessible | current | Each row represents a single LDP Hello Adjacency. An LDP Session can have one or more Hello adjacencies. |
| 1.3.6.1.4.1.9.10.65.1.3.2.1.1.1 | ColumnmplsLdpHelloAdjacencyIndex | not-accessible | current | An identifier for this specific adjacency. |
| 1.3.6.1.4.1.9.10.65.1.3.2.1.1.2 | ColumnmplsLdpHelloAdjacencyHoldTimeRemaining | read-only | current | The time remaining for this Hello Adjacency. This interval will change when the 'next' Hello message which corresponds to this Hello Adjacency is received. |
| 1.3.6.1.4.1.9.10.65.1.3.2.1.1.3 | ColumnmplsLdpHelloAdjacencyType | read-only | current | This adjacency is the result of a 'link' hello if the value of this object is link(1). Otherwise, it is a result of a 'targeted' hello, targeted(2). |
| 1.3.6.1.4.1.9.10.65.1.3.3 | NodemplsLdpSessionObjects | |||
| 1.3.6.1.4.1.9.10.65.1.3.3.1 | ScalarmplsLdpSessionUpDownTrapEnable | read-write | current | Indicates whether the traps, 'mplsLdpSessionUp' and 'mplsLdpSessionDown' will be generated or not. If the value of this object is 'enabled(1)' then the traps w… |
| 1.3.6.1.4.1.9.10.65.1.3.3.2 | TablemplsLdpSessionTable | not-accessible | current | A table of Sessions between the LDP Entities and LDP Peers. Each row represents a single session. |
| 1.3.6.1.4.1.9.10.65.1.3.3.2.1 | RowmplsLdpSessionEntry | not-accessible | current | An entry in this table represents information on a single session between an LDP Entity and LDP Peer. The information contained in a row is read-only. |
| 1.3.6.1.4.1.9.10.65.1.3.3.2.1.1 | ColumnmplsLdpSessionState | read-only | current | The current state of the session, all of the states 1 - 5 are based on the state machine for session negotiation behavior. |
| 1.3.6.1.4.1.9.10.65.1.3.3.2.1.2 | ColumnmplsLdpSessionProtocolVersion | read-only | current | The version of the LDP Protocol which this session is using. |
| 1.3.6.1.4.1.9.10.65.1.3.3.2.1.3 | ColumnmplsLdpSessionKeepAliveHoldTimeRemaining | read-only | current | The keep alive hold time remaining for this session. |
| 1.3.6.1.4.1.9.10.65.1.3.3.2.1.4 | ColumnmplsLdpSessionMaxPduLength | read-only | current | The value of maximum allowable length for LDP PDUs for this session. This value may have been negotiated during the Session Initialization. |
| 1.3.6.1.4.1.9.10.65.1.3.3.2.1.5 | ColumnmplsLdpSessionDiscontinuityTime | read-only | current | The value of sysUpTime on the most recent occasion at which any one or more of this session's counters suffered a discontinuity. The relevant counters are the … |
| 1.3.6.1.4.1.9.10.65.1.3.3.4 | TablemplsLdpAtmSessionTable | not-accessible | current | A table which relates Sessions in the 'mplsLdpSessionTable' and their label range intersections. There could be one or more label range intersections between a… |
| 1.3.6.1.4.1.9.10.65.1.3.3.4.1 | RowmplsLdpAtmSessionEntry | not-accessible | current | An entry in this table represents information on a single label range intersection between an LDP Entity and LDP Peer. The information contained in a row is re… |
| 1.3.6.1.4.1.9.10.65.1.3.3.4.1.1 | ColumnmplsLdpSessionAtmLabelRangeLowerBoundVpi | not-accessible | current | The minimum VPI number for this range. |
| 1.3.6.1.4.1.9.10.65.1.3.3.4.1.2 | ColumnmplsLdpSessionAtmLabelRangeLowerBoundVci | not-accessible | current | The minimum VCI number for this range. |
| 1.3.6.1.4.1.9.10.65.1.3.3.4.1.3 | ColumnmplsLdpSessionAtmLabelRangeUpperBoundVpi | read-only | current | The maximum VPI number for this range. |
| 1.3.6.1.4.1.9.10.65.1.3.3.4.1.4 | ColumnmplsLdpSessionAtmLabelRangeUpperBoundVci | read-only | current | The maximum VCI number for this range. |
| 1.3.6.1.4.1.9.10.65.1.3.3.5 | TablemplsLdpFrameRelaySessionTable | not-accessible | current | A table of Frame Relay label range intersections between the LDP Entities and LDP Peers. Each row represents a single label range intersection. NOTE: this tabl… |
| 1.3.6.1.4.1.9.10.65.1.3.3.5.1 | RowmplsLdpFrameRelaySessionEntry | not-accessible | current | An entry in this table represents information on a single label range intersection between an LDP Entity and LDP Peer. The information contained in a row is re… |
| 1.3.6.1.4.1.9.10.65.1.3.3.5.1.1 | ColumnmplsLdpFrSessionMinDlci | not-accessible | current | The lower bound of DLCIs which are supported. |
| 1.3.6.1.4.1.9.10.65.1.3.3.5.1.2 | ColumnmplsLdpFrSessionMaxDlci | read-only | current | The upper bound of DLCIs which are supported. |
| 1.3.6.1.4.1.9.10.65.1.3.3.5.1.3 | ColumnmplsLdpFrSessionLen | read-only | current | This object specifies the DLCI bits. |
| 1.3.6.1.4.1.9.10.65.1.3.3.6 | TablemplsLdpSessionStatsTable | not-accessible | current | A table of statistics for Sessions between LDP Entities and LDP Peers. |
| 1.3.6.1.4.1.9.10.65.1.3.3.6.1 | RowmplsLdpSessionStatsEntry | not-accessible | current | An entry in this table represents statistical information on a single session between an LDP Entity and LDP Peer. |
| 1.3.6.1.4.1.9.10.65.1.3.3.6.1.1 | ColumnmplsLdpSessionStatsUnknownMessageTypeErrors | read-only | current | This object counts the number of Unknown Message Type Errors detected during this session. Discontinuities in the value of this counter can occur at re-initial… |
| 1.3.6.1.4.1.9.10.65.1.3.3.6.1.2 | ColumnmplsLdpSessionStatsUnknownTlvErrors | read-only | current | This object counts the number of Unknown TLV Errors detected during this session. Discontinuities in the value of this counter can occur at re-initialization o… |
| 1.3.6.1.4.1.9.10.65.1.3.3.7 | TablemplsLdpSessionPeerAddressTable | not-accessible | current | This table 'extends' the mplsLdpSessionTable. This table is used to store Label Address Information from Label Address Messages received by this LSR from Peers… |
| 1.3.6.1.4.1.9.10.65.1.3.3.7.1 | RowmplsLdpSessionPeerAddressEntry | not-accessible | current | An entry in this table represents information on session's for a single next hop address which was advertised in an Address Message from the LDP peer. The info… |
| 1.3.6.1.4.1.9.10.65.1.3.3.7.1.1 | ColumnmplsLdpSessionPeerAddressIndex | not-accessible | current | An index which uniquely identifies this entry within a given session. |
| 1.3.6.1.4.1.9.10.65.1.3.3.7.1.2 | ColumnmplsLdpSessionPeerNextHopAddressType | read-only | current | The internetwork layer address type of this Next Hop Address as specified in the Label Address Message associated with this Session. The value of this object i… |
| 1.3.6.1.4.1.9.10.65.1.3.3.7.1.3 | ColumnmplsLdpSessionPeerNextHopAddress | read-only | current | The value of the next hop address. |
| 1.3.6.1.4.1.9.10.65.1.6 | NodemplsLdpLibObjects | |||
| 1.3.6.1.4.1.9.10.65.1.6.1 | ScalarmplsLdpLibLspUpDownTrapEnable | read-write | current | Indicates whether traps related to an LSP's operation status should be sent. If the value of this object is 'enabled(1)' then the 'mplsLdpLibLspUp' and the 'mp… |
| 1.3.6.1.4.1.9.10.65.1.6.2 | TablemplsLdpLibTable | not-accessible | current | This table represents LIB (Label Information Base) Information. The table is read-only. |
| 1.3.6.1.4.1.9.10.65.1.6.2.1 | RowmplsLdpLibEntry | not-accessible | current | Each row represents a single LDP LIB entry. |
| 1.3.6.1.4.1.9.10.65.1.6.2.1.1 | ColumnmplsLdpLibLspId | not-accessible | current | This number is used to uniquely identify this row, since this row is associated with a specific LSP, it may also be used to describe a unique number for an LSP… |
| 1.3.6.1.4.1.9.10.65.1.6.2.1.2 | ColumnmplsLdpLibLabelInIfIndex | read-only | current | The ifIndex of the 'mplsLdpInLabel'. |
| 1.3.6.1.4.1.9.10.65.1.6.2.1.3 | ColumnmplsLdpLibLabelOutIfIndex | read-only | current | The ifIndex of the 'mplsLdpOutLabel'. |
| 1.3.6.1.4.1.9.10.65.1.6.2.1.4 | ColumnmplsLdpLibInLabelType | read-only | current | The Layer 2 Label Type for 'mplsLdpInLabel'. |
| 1.3.6.1.4.1.9.10.65.1.6.2.1.5 | ColumnmplsLdpLibInLabel | read-only | current | The incoming label of this LSP. |
| 1.3.6.1.4.1.9.10.65.1.6.2.1.6 | ColumnmplsLdpLibOutLabelType | read-only | current | The Layer 2 Label Type for 'mplsLdpOutLabel'. |
| 1.3.6.1.4.1.9.10.65.1.6.2.1.7 | ColumnmplsLdpLibOutLabel | read-only | current | The outgoing label of this LSP. |
| 1.3.6.1.4.1.9.10.65.1.6.2.1.8 | ColumnmplsLdpLibOperationStatus | read-only | current | |
| 1.3.6.1.4.1.9.10.65.1.6.2.1.9 | ColumnmplsLdpLibLspLastChange | read-only | current | The value of sysUpTime on the most recent occasion that the 'mplsLdpLibOperationStatus' changed. If the status has not changed since the last re-initialization… |
| 1.3.6.1.4.1.9.10.65.1.6.3 | TablemplsLdpFecTable | not-accessible | current | This table represents the FEC (Forwarding Equivalence Class) Information associated with an LSP. The table is read-only. |
| 1.3.6.1.4.1.9.10.65.1.6.3.1 | RowmplsLdpFecEntry | not-accessible | current | Each row represents a single FEC Element. |
| 1.3.6.1.4.1.9.10.65.1.6.3.1.1 | ColumnmplsLdpFecType | not-accessible | current | The type of the FEC. If the value of this object is 'prefix(1)' then the FEC type described by this row is for address prefixes. If the value of this object is… |
| 1.3.6.1.4.1.9.10.65.1.6.3.1.2 | ColumnmplsLdpFecAddressFamily | not-accessible | current | The value of this object is from the Address Family Numbers. |
| 1.3.6.1.4.1.9.10.65.1.6.3.1.3 | ColumnmplsLdpFecAddressLength | not-accessible | current | If the value of 'mplsLdpFecType' is 'prefix(1)' then the value of this object is the length in bits of the address prefix represented by 'mplsLdpFecAddress', o… |
| 1.3.6.1.4.1.9.10.65.1.6.3.1.4 | ColumnmplsLdpFecAddress | not-accessible | current | If the value of 'mplsLdpFecType' is 'prefix(1)' then the value of this object is the address prefix. If the value of the 'mplsLdpFecAddressLength' is object is… |
| 1.3.6.1.4.1.9.10.65.1.6.3.1.5 | ColumnmplsLdpFecLspId | not-accessible | current | This number represents the LSP which is related to this FEC. The value of this index should correspond to the 'mplsLdpLibLspId' in the LIB table. |
| 1.3.6.1.4.1.9.10.65.1.6.3.1.6 | ColumnmplsLdpFecSessionRowPointer | read-only | current | A pointer to a row in the 'mplsLdpSessionTable' which is related to this FEC entry. The NULL OID zeroDotzero is interpreted to mean there is no known Session r… |
| 1.3.6.1.4.1.9.10.65.2 | NodemplsLdpNotifications | |||
| 1.3.6.1.4.1.9.10.65.2.0 | NodemplsLdpNotificationPrefix | |||
| 1.3.6.1.4.1.9.10.65.2.0.1 | NotificationmplsLdpFailedInitSessionThresholdExceeded | current | This notification is generated when the value of the 'mplsLdpEntityPVLimitMismatchTrapEnable' object is 'enabled(1)' and the value of the object, 'mplsLdpEntit… | |
| 1.3.6.1.4.1.9.10.65.2.0.2 | NotificationmplsLdpPathVectorLimitMismatch | current | This notification is generated when the value of the value of the object, 'mplsLdpEntityFailedInitSessionTrapEnable' is 'enabled(1)' and the 'mplsLdpEntityPath… | |
| 1.3.6.1.4.1.9.10.65.2.0.3 | NotificationmplsLdpSessionUp | current | Generation of this trap occurs when the 'mplsLdpSessionUpDownTrapEnable' object is 'enabled(1)' and the value of mplsLdpSessionState changes from any state acc… | |
| 1.3.6.1.4.1.9.10.65.2.0.4 | NotificationmplsLdpSessionDown | current | Generation of this trap occurs when the 'mplsLdpSessionUpDownTrapEnable' object is 'enabled(1)' and the value of mplsLdpSessionState changes from 'operational(… | |
| 1.3.6.1.4.1.9.10.65.2.0.5 | NotificationmplsLdpLibLspUp | current | Generation of this trap occurs when the 'mplsLdpLibLspUpDownTrapEnable' object is 'enabled(1)' and the LSP operation status changes from any state to 'up'. | |
| 1.3.6.1.4.1.9.10.65.2.0.6 | NotificationmplsLdpLibLspDown | current | Generation of this trap occurs when the 'mplsLdpLibLspUpDownTrapEnable' object is 'enabled(1)' and the LSP operation status changes from any state to 'down'. | |
| 1.3.6.1.4.1.9.10.65.3 | NodemplsLdpConformance | |||
| 1.3.6.1.4.1.9.10.65.3.1 | NodemplsLdpGroups | |||
| 1.3.6.1.4.1.9.10.65.3.1.1 | GroupmplsLdpGeneralGroup | current | Objects that apply to all MPLS LDP implementations. | |
| 1.3.6.1.4.1.9.10.65.3.1.2 | GroupmplsLdpGenericGroup | current | Objects that apply to all MPLS LDP implementations using Generic Lables. | |
| 1.3.6.1.4.1.9.10.65.3.1.3 | GroupmplsLdpAtmGroup | current | Objects that apply to all MPLS LDP implementations over ATM. | |
| 1.3.6.1.4.1.9.10.65.3.1.4 | GroupmplsLdpFrameRelayGroup | current | Objects that apply to all MPLS LDP implementations over Frame Relay. | |
| 1.3.6.1.4.1.9.10.65.3.1.5 | GroupmplsLdpNotificationsGroup | current | The notification(s) which an MPLS LDP implemention is required to implement. | |
| 1.3.6.1.4.1.9.10.65.3.2 | NodemplsLdpCompliances | |||
| 1.3.6.1.4.1.9.10.65.3.2.1 | CompliancemplsLdpModuleCompliance | current | The basic implentation requirements for agents that support the MPLS LDP MIB. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| AtmVcIdentifier | INTEGER (0..65535) | current | The VCI value for a VCL. The maximum VCI value cannot exceed the value allowable by atmInterfaceMaxVciBits defined in ATM-MIB. |
| AtmVpIdentifier | INTEGER (0..4095) | current | The VPI value for a VPL or VCL. The value VPI=0 is only allowed for a VCL. For ATM UNIs supporting VPCs the VPI value ranges from 0 to 255. The VPI value 0 is supported for ATM UNIs conforming to the ATM Forum UNI 4.0 A… |
| MplsLabel | Unsigned32 (0..4294967295) | current | Represents an MPLS label. The label contents are are specific to the label being represented. The label carried in an MPLS shim header (for LDP, the Generic Label) is a 20-bit number represented by 4 octets. Bits 0-19 c… |
| MplsLdpGenAddr | OCTET STRING (SIZE (0..64)) | current | The value of an network layer or data link layer address. |
| MplsLdpIdentifier | OCTET STRING (SIZE (6)) | current | The LDP identifier is a six octet quantity which is used to identify an Label Switch Router (LSR) label space. The first four octets encode an IP address assigned to the LSR, and the last two octets identify a specific … |
| MplsLdpLabelTypes | INTEGER { generic(1), atm(2), frameRelay(3) } | current | The Layer 2 label types which are defined for MPLS LDP are generic(1), atm(2), or frameRelay(3). |
| MplsLsrIdentifier | OCTET STRING (SIZE (4)) | current | The Label Switch Router (LSR) identifier is the first 4 bytes or the IP Address component of the Label Distribution Protocol (LDP) identifier. |