MPLS-TE-STD-MIB
133 objects
Copyright (C) The Internet Society (2004). The initial version of this MIB module was published in RFC 3812. For full legal notices see the RFC itself or see: http://www.ietf.org/copyrights/ianamib.html This MIB module contains managed object definitions for MPLS Traffic Engineering (TE) as defined in: 1. Extensions to RSVP for LSP Tunnels, Awduche et al, RFC 3209, December 2001 2. Constraint-Based LSP Setup using LDP, Jamoussi (Editor), RFC 3212, January 2002 3. Requirements for Traffic Engineering Over MPLS, Awduche, D., Malcolm, J., Agogbua, J., O'Dell, M., and J. McManus, [RFC2702], September 1999
Imported Objects
| DIFFSERV-MIB | IndexIntegerNextFree |
| IF-MIB | ifCounterDiscontinuityGroup ifGeneralInformationGroup InterfaceIndexOrZero |
| INET-ADDRESS-MIB | InetAddressPrefixLength |
| MPLS-TC-STD-MIB | MplsBitRate MplsBurstSize MplsExtendedTunnelId MplsLSPID MplsOwner MplsPathIndex MplsPathIndexOrZero mplsStdMIB MplsTunnelAffinity MplsTunnelIndex MplsTunnelInstanceIndex TeHopAddress TeHopAddressAS TeHopAddressType TeHopAddressUnnum |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Counter64 Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE TimeTicks Unsigned32 zeroDotZero |
| SNMPv2-TC | RowPointer RowStatus StorageType TimeStamp TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.2.1.10.166.3 | IdentitymplsTeStdMIB | Copyright (C) The Internet Society (2004). The initial version of this MIB module was published in RFC 3812. For full legal notices see the RFC itself or see: … | ||
| 1.3.6.1.2.1.10.166.3.0 | NodemplsTeNotifications | |||
| 1.3.6.1.2.1.10.166.3.0.1 | NotificationmplsTunnelUp | current | This notification is generated when a mplsTunnelOperStatus object for one of the configured tunnels is about to leave the down state and transition into some o… | |
| 1.3.6.1.2.1.10.166.3.0.2 | NotificationmplsTunnelDown | current | This notification is generated when a mplsTunnelOperStatus object for one of the configured tunnels is about to enter the down state from some other state (but… | |
| 1.3.6.1.2.1.10.166.3.0.3 | NotificationmplsTunnelRerouted | current | This notification is generated when a tunnel is rerouted. If the mplsTunnelARHopTable is used, then this tunnel instance's entry in the mplsTunnelARHopTable MA… | |
| 1.3.6.1.2.1.10.166.3.0.4 | NotificationmplsTunnelReoptimized | current | This notification is generated when a tunnel is reoptimized. If the mplsTunnelARHopTable is used, then this tunnel instance's entry in the mplsTunnelARHopTable… | |
| 1.3.6.1.2.1.10.166.3.1 | NodemplsTeScalars | |||
| 1.3.6.1.2.1.10.166.3.1.1 | ScalarmplsTunnelConfigured | read-only | current | The number of tunnels configured on this device. A tunnel is considered configured if the mplsTunnelRowStatus is active(1). |
| 1.3.6.1.2.1.10.166.3.1.2 | ScalarmplsTunnelActive | read-only | current | The number of tunnels active on this device. A tunnel is considered active if the mplsTunnelOperStatus is up(1). |
| 1.3.6.1.2.1.10.166.3.1.3 | ScalarmplsTunnelTEDistProto | read-only | current | The traffic engineering distribution protocol(s) used by this LSR. Note that an LSR may support more than one distribution protocol simultaneously. |
| 1.3.6.1.2.1.10.166.3.1.4 | ScalarmplsTunnelMaxHops | read-only | current | The maximum number of hops that can be specified for a tunnel on this device. |
| 1.3.6.1.2.1.10.166.3.1.5 | ScalarmplsTunnelNotificationMaxRate | read-write | current | This variable indicates the maximum number of notifications issued per second. If events occur more rapidly, the implementation may simply fail to emit these n… |
| 1.3.6.1.2.1.10.166.3.2 | NodemplsTeObjects | |||
| 1.3.6.1.2.1.10.166.3.2.1 | ScalarmplsTunnelIndexNext | read-only | current | This object contains an unused value for mplsTunnelIndex, or a zero to indicate that none exist. Negative values are not allowed, as they do not correspond to … |
| 1.3.6.1.2.1.10.166.3.2.2 | TablemplsTunnelTable | not-accessible | current | The mplsTunnelTable allows new MPLS tunnels to be created between an LSR and a remote endpoint, and existing tunnels to be reconfigured or removed. Note that o… |
| 1.3.6.1.2.1.10.166.3.2.2.1 | RowmplsTunnelEntry | not-accessible | current | An entry in this table represents an MPLS tunnel. An entry can be created by a network administrator or by an SNMP agent as instructed by an MPLS signalling pr… |
| 1.3.6.1.2.1.10.166.3.2.2.1.1 | ColumnmplsTunnelIndex | not-accessible | current | Uniquely identifies a set of tunnel instances between a pair of ingress and egress LSRs. Managers should obtain new values for row creation in this table by re… |
| 1.3.6.1.2.1.10.166.3.2.2.1.2 | ColumnmplsTunnelInstance | not-accessible | current | Uniquely identifies a particular instance of a tunnel between a pair of ingress and egress LSRs. It is useful to identify multiple instances of tunnels for the… |
| 1.3.6.1.2.1.10.166.3.2.2.1.3 | ColumnmplsTunnelIngressLSRId | not-accessible | current | Identity of the ingress LSR associated with this tunnel instance. When the MPLS signalling protocol is rsvp(2) this value SHOULD be equal to the Tunnel Sender … |
| 1.3.6.1.2.1.10.166.3.2.2.1.4 | ColumnmplsTunnelEgressLSRId | not-accessible | current | Identity of the egress LSR associated with this tunnel instance. |
| 1.3.6.1.2.1.10.166.3.2.2.1.5 | ColumnmplsTunnelName | read-create | current | The canonical name assigned to the tunnel. This name can be used to refer to the tunnel on the LSR's console port. If mplsTunnelIsIf is set to true then the if… |
| 1.3.6.1.2.1.10.166.3.2.2.1.6 | ColumnmplsTunnelDescr | read-create | current | A textual string containing information about the tunnel. If there is no description this object contains a zero length string. This object is may not be signa… |
| 1.3.6.1.2.1.10.166.3.2.2.1.7 | ColumnmplsTunnelIsIf | read-create | current | Denotes whether or not this tunnel corresponds to an interface represented in the interfaces group table. Note that if this variable is set to true then the if… |
| 1.3.6.1.2.1.10.166.3.2.2.1.8 | ColumnmplsTunnelIfIndex | read-only | current | If mplsTunnelIsIf is set to true, then this value contains the LSR-assigned ifIndex which corresponds to an entry in the interfaces table. Otherwise this varia… |
| 1.3.6.1.2.1.10.166.3.2.2.1.9 | ColumnmplsTunnelOwner | read-only | current | Denotes the entity that created and is responsible for managing this tunnel. This column is automatically filled by the agent on creation of a row. |
| 1.3.6.1.2.1.10.166.3.2.2.1.10 | ColumnmplsTunnelRole | read-create | current | This value signifies the role that this tunnel entry/instance represents. This value MUST be set to head(1) at the originating point of the tunnel. This value … |
| 1.3.6.1.2.1.10.166.3.2.2.1.11 | ColumnmplsTunnelXCPointer | read-create | current | This variable points to a row in the mplsXCTable. This table identifies the segments that compose this tunnel, their characteristics, and relationships to each… |
| 1.3.6.1.2.1.10.166.3.2.2.1.12 | ColumnmplsTunnelSignallingProto | read-create | current | The signalling protocol, if any, used to setup this tunnel. |
| 1.3.6.1.2.1.10.166.3.2.2.1.13 | ColumnmplsTunnelSetupPrio | read-create | current | Indicates the setup priority of this tunnel. |
| 1.3.6.1.2.1.10.166.3.2.2.1.14 | ColumnmplsTunnelHoldingPrio | read-create | current | Indicates the holding priority for this tunnel. |
| 1.3.6.1.2.1.10.166.3.2.2.1.15 | ColumnmplsTunnelSessionAttributes | read-create | current | This bit mask indicates optional session values for this tunnel. The following describes these bit fields: fastRerouteThis flag indicates that the any tunnel h… |
| 1.3.6.1.2.1.10.166.3.2.2.1.16 | ColumnmplsTunnelLocalProtectInUse | read-create | current | Indicates that the local repair mechanism is in use to maintain this tunnel (usually in the face of an outage of the link it was previously routed over). |
| 1.3.6.1.2.1.10.166.3.2.2.1.17 | ColumnmplsTunnelResourcePointer | read-create | current | This variable represents a pointer to the traffic parameter specification for this tunnel. This value may point at an entry in the mplsTunnelResourceEntry to i… |
| 1.3.6.1.2.1.10.166.3.2.2.1.18 | ColumnmplsTunnelPrimaryInstance | read-only | current | Specifies the instance index of the primary instance of this tunnel. More details of the definition of tunnel instances and the primary tunnel instance can be … |
| 1.3.6.1.2.1.10.166.3.2.2.1.19 | ColumnmplsTunnelInstancePriority | read-create | current | This value indicates which priority, in descending order, with 0 indicating the lowest priority, within a group of tunnel instances. A group of tunnel instance… |
| 1.3.6.1.2.1.10.166.3.2.2.1.20 | ColumnmplsTunnelHopTableIndex | read-create | current | Index into the mplsTunnelHopTable entry that specifies the explicit route hops for this tunnel. This object is meaningful only at the head-end of the tunnel. |
| 1.3.6.1.2.1.10.166.3.2.2.1.21 | ColumnmplsTunnelPathInUse | read-create | current | This value denotes the configured path that was chosen for this tunnel. This value reflects the secondary index into mplsTunnelHopTable. This path may not exac… |
| 1.3.6.1.2.1.10.166.3.2.2.1.22 | ColumnmplsTunnelARHopTableIndex | read-only | current | Index into the mplsTunnelARHopTable entry that specifies the actual hops traversed by the tunnel. This is automatically updated by the agent when the actual ho… |
| 1.3.6.1.2.1.10.166.3.2.2.1.23 | ColumnmplsTunnelCHopTableIndex | read-only | current | Index into the mplsTunnelCHopTable entry that specifies the computed hops traversed by the tunnel. This is automatically updated by the agent when computed hop… |
| 1.3.6.1.2.1.10.166.3.2.2.1.24 | ColumnmplsTunnelIncludeAnyAffinity | read-create | current | A link satisfies the include-any constraint if and only if the constraint is zero, or the link and the constraint have a resource class in common. |
| 1.3.6.1.2.1.10.166.3.2.2.1.25 | ColumnmplsTunnelIncludeAllAffinity | read-create | current | A link satisfies the include-all constraint if and only if the link contains all of the administrative groups specified in the constraint. |
| 1.3.6.1.2.1.10.166.3.2.2.1.26 | ColumnmplsTunnelExcludeAnyAffinity | read-create | current | A link satisfies the exclude-any constraint if and only if the link contains none of the administrative groups specified in the constraint. |
| 1.3.6.1.2.1.10.166.3.2.2.1.27 | ColumnmplsTunnelTotalUpTime | read-only | current | This value represents the aggregate up time for all instances of this tunnel, if available. If this value is unavailable, it MUST return a value of 0. |
| 1.3.6.1.2.1.10.166.3.2.2.1.28 | ColumnmplsTunnelInstanceUpTime | read-only | current | This value identifies the total time that this tunnel instance's operStatus has been Up(1). |
| 1.3.6.1.2.1.10.166.3.2.2.1.29 | ColumnmplsTunnelPrimaryUpTime | read-only | current | Specifies the total time the primary instance of this tunnel has been active. The primary instance of this tunnel is defined in mplsTunnelPrimaryInstance. |
| 1.3.6.1.2.1.10.166.3.2.2.1.30 | ColumnmplsTunnelPathChanges | read-only | current | Specifies the number of times the actual path for this tunnel instance has changed. |
| 1.3.6.1.2.1.10.166.3.2.2.1.31 | ColumnmplsTunnelLastPathChange | read-only | current | Specifies the time since the last change to the actual path for this tunnel instance. |
| 1.3.6.1.2.1.10.166.3.2.2.1.32 | ColumnmplsTunnelCreationTime | read-only | current | Specifies the value of SysUpTime when the first instance of this tunnel came into existence. That is, when the value of mplsTunnelOperStatus was first set to u… |
| 1.3.6.1.2.1.10.166.3.2.2.1.33 | ColumnmplsTunnelStateTransitions | read-only | current | Specifies the number of times the state (mplsTunnelOperStatus) of this tunnel instance has changed. |
| 1.3.6.1.2.1.10.166.3.2.2.1.34 | ColumnmplsTunnelAdminStatus | read-create | current | Indicates the desired operational status of this tunnel. |
| 1.3.6.1.2.1.10.166.3.2.2.1.35 | ColumnmplsTunnelOperStatus | read-only | current | Indicates the actual operational status of this tunnel, which is typically but not limited to, a function of the state of individual segments of this tunnel. |
| 1.3.6.1.2.1.10.166.3.2.2.1.36 | ColumnmplsTunnelRowStatus | read-create | current | This variable is used to create, modify, and/or delete a row in this table. When a row in this table is in active(1) state, no objects in that row can be modif… |
| 1.3.6.1.2.1.10.166.3.2.2.1.37 | ColumnmplsTunnelStorageType | read-create | current | The storage type for this tunnel entry. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row. |
| 1.3.6.1.2.1.10.166.3.2.3 | ScalarmplsTunnelHopListIndexNext | read-only | current | This object contains an appropriate value to be used for mplsTunnelHopListIndex when creating entries in the mplsTunnelHopTable. If the number of unassigned en… |
| 1.3.6.1.2.1.10.166.3.2.4 | TablemplsTunnelHopTable | not-accessible | current | The mplsTunnelHopTable is used to indicate the hops, strict or loose, for an instance of an MPLS tunnel defined in mplsTunnelTable, when it is established via … |
| 1.3.6.1.2.1.10.166.3.2.4.1 | RowmplsTunnelHopEntry | not-accessible | current | An entry in this table represents a tunnel hop. An entry is created by a network administrator for signaled ERLSP set up by an MPLS signalling protocol. |
| 1.3.6.1.2.1.10.166.3.2.4.1.1 | ColumnmplsTunnelHopListIndex | not-accessible | current | Primary index into this table identifying a particular explicit route object. |
| 1.3.6.1.2.1.10.166.3.2.4.1.2 | ColumnmplsTunnelHopPathOptionIndex | not-accessible | current | Secondary index into this table identifying a particular group of hops representing a particular configured path. This is otherwise known as a path option. |
| 1.3.6.1.2.1.10.166.3.2.4.1.3 | ColumnmplsTunnelHopIndex | not-accessible | current | Tertiary index into this table identifying a particular hop. |
| 1.3.6.1.2.1.10.166.3.2.4.1.4 | ColumnmplsTunnelHopAddrType | read-create | current | The Hop Address Type of this tunnel hop. The value of this object cannot be changed if the value of the corresponding mplsTunnelHopRowStatus object is 'active'… |
| 1.3.6.1.2.1.10.166.3.2.4.1.5 | ColumnmplsTunnelHopIpAddr | read-create | current | The Tunnel Hop Address for this tunnel hop. The type of this address is determined by the value of the corresponding mplsTunnelHopAddrType. The value of this o… |
| 1.3.6.1.2.1.10.166.3.2.4.1.6 | ColumnmplsTunnelHopIpPrefixLen | read-create | current | If mplsTunnelHopAddrType is set to ipv4(1) or ipv6(2), then this value will contain an appropriate prefix length for the IP address in object mplsTunnelHopIpAd… |
| 1.3.6.1.2.1.10.166.3.2.4.1.7 | ColumnmplsTunnelHopAsNumber | read-create | current | If mplsTunnelHopAddrType is set to asnumber(3), then this value will contain the AS number of this hop. Otherwise the agent should set this object to zero- len… |
| 1.3.6.1.2.1.10.166.3.2.4.1.8 | ColumnmplsTunnelHopAddrUnnum | read-create | current | If mplsTunnelHopAddrType is set to unnum(4), then this value will contain the interface identifier of the unnumbered interface for this hop. This object should… |
| 1.3.6.1.2.1.10.166.3.2.4.1.9 | ColumnmplsTunnelHopLspId | read-create | current | If mplsTunnelHopAddrType is set to lspid(5), then this value will contain the LSPID of a tunnel of this hop. The present tunnel being configured is tunneled th… |
| 1.3.6.1.2.1.10.166.3.2.4.1.10 | ColumnmplsTunnelHopType | read-create | current | Denotes whether this tunnel hop is routed in a strict or loose fashion. The value of this object has no meaning if the mplsTunnelHopInclude object is set to 'f… |
| 1.3.6.1.2.1.10.166.3.2.4.1.11 | ColumnmplsTunnelHopInclude | read-create | current | If this value is set to true, then this indicates that this hop must be included in the tunnel's path. If this value is set to 'false', then this hop must be a… |
| 1.3.6.1.2.1.10.166.3.2.4.1.12 | ColumnmplsTunnelHopPathOptionName | read-create | current | The description of this series of hops as they relate to the specified path option. The value of this object SHOULD be the same for each hop in the series that… |
| 1.3.6.1.2.1.10.166.3.2.4.1.13 | ColumnmplsTunnelHopEntryPathComp | read-create | current | If this value is set to dynamic, then the user should only specify the source and destination of the path and expect that the CSPF will calculate the remainder… |
| 1.3.6.1.2.1.10.166.3.2.4.1.14 | ColumnmplsTunnelHopRowStatus | read-create | current | This variable is used to create, modify, and/or delete a row in this table. When a row in this table is in active(1) state, no objects in that row can be modif… |
| 1.3.6.1.2.1.10.166.3.2.4.1.15 | ColumnmplsTunnelHopStorageType | read-create | current | The storage type for this Hop entry. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row. |
| 1.3.6.1.2.1.10.166.3.2.5 | ScalarmplsTunnelResourceIndexNext | read-only | current | This object contains the next appropriate value to be used for mplsTunnelResourceIndex when creating entries in the mplsTunnelResourceTable. If the number of u… |
| 1.3.6.1.2.1.10.166.3.2.6 | TablemplsTunnelResourceTable | not-accessible | current | The mplsTunnelResourceTable allows a manager to specify which resources are desired for an MPLS tunnel. This table also allows several tunnels to point to a si… |
| 1.3.6.1.2.1.10.166.3.2.6.1 | RowmplsTunnelResourceEntry | not-accessible | current | An entry in this table represents a set of resources for an MPLS tunnel. An entry can be created by a network administrator or by an SNMP agent as instructed b… |
| 1.3.6.1.2.1.10.166.3.2.6.1.1 | ColumnmplsTunnelResourceIndex | not-accessible | current | Uniquely identifies this row. |
| 1.3.6.1.2.1.10.166.3.2.6.1.2 | ColumnmplsTunnelResourceMaxRate | read-create | current | The maximum rate in bits/second. Note that setting mplsTunnelResourceMaxRate, mplsTunnelResourceMeanRate, and mplsTunnelResourceMaxBurstSize to 0 indicates bes… |
| 1.3.6.1.2.1.10.166.3.2.6.1.3 | ColumnmplsTunnelResourceMeanRate | read-create | current | This object is copied into an instance of mplsTrafficParamMeanRate in the mplsTrafficParamTable. The OID of this table entry is then copied into the correspond… |
| 1.3.6.1.2.1.10.166.3.2.6.1.4 | ColumnmplsTunnelResourceMaxBurstSize | read-create | current | The maximum burst size in bytes. |
| 1.3.6.1.2.1.10.166.3.2.6.1.5 | ColumnmplsTunnelResourceMeanBurstSize | read-create | current | The mean burst size in bytes. The implementations which do not implement this variable must return a noSuchObject exception for this object and must not allow … |
| 1.3.6.1.2.1.10.166.3.2.6.1.6 | ColumnmplsTunnelResourceExBurstSize | read-create | current | The Excess burst size in bytes. The implementations which do not implement this variable must return noSuchObject exception for this object and must not allow … |
| 1.3.6.1.2.1.10.166.3.2.6.1.7 | ColumnmplsTunnelResourceFrequency | read-create | current | The granularity of the availability of committed rate. The implementations which do not implement this variable must return unspecified(1) for this value and m… |
| 1.3.6.1.2.1.10.166.3.2.6.1.8 | ColumnmplsTunnelResourceWeight | read-create | current | The relative weight for using excess bandwidth above its committed rate. The value of 0 means that weight is not applicable for the CR-LSP. |
| 1.3.6.1.2.1.10.166.3.2.6.1.9 | ColumnmplsTunnelResourceRowStatus | read-create | current | This variable is used to create, modify, and/or delete a row in this table. When a row in this table is in active(1) state, no objects in that row can be modif… |
| 1.3.6.1.2.1.10.166.3.2.6.1.10 | ColumnmplsTunnelResourceStorageType | read-create | current | The storage type for this Hop entry. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row. |
| 1.3.6.1.2.1.10.166.3.2.7 | TablemplsTunnelARHopTable | not-accessible | current | The mplsTunnelARHopTable is used to indicate the hops for an MPLS tunnel defined in mplsTunnelTable, as reported by the MPLS signalling protocol. Thus at a tra… |
| 1.3.6.1.2.1.10.166.3.2.7.1 | RowmplsTunnelARHopEntry | not-accessible | current | An entry in this table represents a tunnel hop. An entry is created by the agent for signaled ERLSP set up by an MPLS signalling protocol. |
| 1.3.6.1.2.1.10.166.3.2.7.1.1 | ColumnmplsTunnelARHopListIndex | not-accessible | current | Primary index into this table identifying a particular recorded hop list. |
| 1.3.6.1.2.1.10.166.3.2.7.1.2 | ColumnmplsTunnelARHopIndex | not-accessible | current | Secondary index into this table identifying the particular hop. |
| 1.3.6.1.2.1.10.166.3.2.7.1.3 | ColumnmplsTunnelARHopAddrType | read-only | current | The Hop Address Type of this tunnel hop. Note that lspid(5) is a valid option only for tunnels signaled via CRLDP. |
| 1.3.6.1.2.1.10.166.3.2.7.1.4 | ColumnmplsTunnelARHopIpAddr | read-only | current | The Tunnel Hop Address for this tunnel hop. The type of this address is determined by the value of the corresponding mplsTunnelARHopAddrType. If mplsTunnelARHo… |
| 1.3.6.1.2.1.10.166.3.2.7.1.5 | ColumnmplsTunnelARHopAddrUnnum | read-only | current | If mplsTunnelARHopAddrType is set to unnum(4), then this value will contain the interface identifier of the unnumbered interface for this hop. This object shou… |
| 1.3.6.1.2.1.10.166.3.2.7.1.6 | ColumnmplsTunnelARHopLspId | read-only | current | If mplsTunnelARHopAddrType is set to lspid(5), then this value will contain the LSP ID of this hop. This object is otherwise insignificant and should contain a… |
| 1.3.6.1.2.1.10.166.3.2.8 | TablemplsTunnelCHopTable | not-accessible | current | The mplsTunnelCHopTable is used to indicate the hops, strict or loose, for an MPLS tunnel defined in mplsTunnelTable, as computed by a constraint- based routin… |
| 1.3.6.1.2.1.10.166.3.2.8.1 | RowmplsTunnelCHopEntry | not-accessible | current | An entry in this table represents a tunnel hop. An entry in this table is created by a path computation engine using CSPF techniques applied to the information… |
| 1.3.6.1.2.1.10.166.3.2.8.1.1 | ColumnmplsTunnelCHopListIndex | not-accessible | current | Primary index into this table identifying a particular computed hop list. |
| 1.3.6.1.2.1.10.166.3.2.8.1.2 | ColumnmplsTunnelCHopIndex | not-accessible | current | Secondary index into this table identifying the particular hop. |
| 1.3.6.1.2.1.10.166.3.2.8.1.3 | ColumnmplsTunnelCHopAddrType | read-only | current | The Hop Address Type of this tunnel hop. Note that lspid(5) is a valid option only for tunnels signaled via CRLDP. |
| 1.3.6.1.2.1.10.166.3.2.8.1.4 | ColumnmplsTunnelCHopIpAddr | read-only | current | The Tunnel Hop Address for this tunnel hop. The type of this address is determined by the value of the corresponding mplsTunnelCHopAddrType. If mplsTunnelCHopA… |
| 1.3.6.1.2.1.10.166.3.2.8.1.5 | ColumnmplsTunnelCHopIpPrefixLen | read-only | current | If mplsTunnelCHopAddrType is set to ipv4(1) or ipv6(2), then this value will contain an appropriate prefix length for the IP address in object mplsTunnelCHopIp… |
| 1.3.6.1.2.1.10.166.3.2.8.1.6 | ColumnmplsTunnelCHopAsNumber | read-only | current | If mplsTunnelCHopAddrType is set to asnumber(3), then this value will contain the AS number of this hop. Otherwise the agent should set this object to zero-len… |
| 1.3.6.1.2.1.10.166.3.2.8.1.7 | ColumnmplsTunnelCHopAddrUnnum | read-only | current | If mplsTunnelCHopAddrType is set to unnum(4), then this value will contain the unnumbered interface identifier of this hop. This object should be used in conju… |
| 1.3.6.1.2.1.10.166.3.2.8.1.8 | ColumnmplsTunnelCHopLspId | read-only | current | If mplsTunnelCHopAddrType is set to lspid(5), then this value will contain the LSP ID of this hop. This object is otherwise insignificant and should contain a … |
| 1.3.6.1.2.1.10.166.3.2.8.1.9 | ColumnmplsTunnelCHopType | read-only | current | Denotes whether this is tunnel hop is routed in a strict or loose fashion. |
| 1.3.6.1.2.1.10.166.3.2.9 | TablemplsTunnelPerfTable | not-accessible | current | This table provides per-tunnel instance MPLS performance information. |
| 1.3.6.1.2.1.10.166.3.2.9.1 | RowmplsTunnelPerfEntry | not-accessible | current | An entry in this table is created by the LSR for every tunnel. Its is an extension to mplsTunnelEntry. |
| 1.3.6.1.2.1.10.166.3.2.9.1.1 | ColumnmplsTunnelPerfPackets | read-only | current | Number of packets forwarded by the tunnel. This object should represents the 32-bit value of the least significant part of the 64-bit value if both mplsTunnelP… |
| 1.3.6.1.2.1.10.166.3.2.9.1.2 | ColumnmplsTunnelPerfHCPackets | read-only | current | High capacity counter for number of packets forwarded by the tunnel. |
| 1.3.6.1.2.1.10.166.3.2.9.1.3 | ColumnmplsTunnelPerfErrors | read-only | current | Number of packets dropped because of errors or for other reasons. |
| 1.3.6.1.2.1.10.166.3.2.9.1.4 | ColumnmplsTunnelPerfBytes | read-only | current | Number of bytes forwarded by the tunnel. This object should represents the 32-bit value of the least significant part of the 64-bit value if both mplsTunnelPer… |
| 1.3.6.1.2.1.10.166.3.2.9.1.5 | ColumnmplsTunnelPerfHCBytes | read-only | current | High capacity counter for number of bytes forwarded by the tunnel. |
| 1.3.6.1.2.1.10.166.3.2.10 | TablemplsTunnelCRLDPResTable | not-accessible | current | The mplsTunnelCRLDPResTable allows a manager to specify which CR-LDP-specific resources are desired for an MPLS tunnel if that tunnel is signaled using CR-LDP.… |
| 1.3.6.1.2.1.10.166.3.2.10.1 | RowmplsTunnelCRLDPResEntry | not-accessible | current | An entry in this table represents a set of resources for an MPLS tunnel established using CRLDP (mplsTunnelSignallingProto equal to crldp (3)). An entry can be… |
| 1.3.6.1.2.1.10.166.3.2.10.1.1 | ColumnmplsTunnelCRLDPResMeanBurstSize | read-create | current | The mean burst size in bytes. |
| 1.3.6.1.2.1.10.166.3.2.10.1.2 | ColumnmplsTunnelCRLDPResExBurstSize | read-create | current | The Excess burst size in bytes. |
| 1.3.6.1.2.1.10.166.3.2.10.1.3 | ColumnmplsTunnelCRLDPResFrequency | read-create | current | The granularity of the availability of committed rate. |
| 1.3.6.1.2.1.10.166.3.2.10.1.4 | ColumnmplsTunnelCRLDPResWeight | read-create | current | The relative weight for using excess bandwidth above its committed rate. The value of 0 means that weight is not applicable for the CR-LSP. |
| 1.3.6.1.2.1.10.166.3.2.10.1.5 | ColumnmplsTunnelCRLDPResFlags | read-create | current | The value of the 1 byte Flags conveyed as part of the traffic parameters during the establishment of the CRLSP. The bits in this object are to be interpreted a… |
| 1.3.6.1.2.1.10.166.3.2.10.1.6 | ColumnmplsTunnelCRLDPResRowStatus | read-create | current | This variable is used to create, modify, and/or delete a row in this table. When a row in this table is in active(1) state, no objects in that row can be modif… |
| 1.3.6.1.2.1.10.166.3.2.10.1.7 | ColumnmplsTunnelCRLDPResStorageType | read-create | current | The storage type for this CR-LDP Resource entry. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row. |
| 1.3.6.1.2.1.10.166.3.2.11 | ScalarmplsTunnelNotificationEnable | read-write | current | If this object is true, then it enables the generation of mplsTunnelUp and mplsTunnelDown traps, otherwise these traps are not emitted. |
| 1.3.6.1.2.1.10.166.3.3 | NodemplsTeConformance | |||
| 1.3.6.1.2.1.10.166.3.3.1 | NodemplsTeGroups | |||
| 1.3.6.1.2.1.10.166.3.3.1.1 | GroupmplsTunnelGroup | current | Necessary, but not sufficient, set of objects to implement tunnels. In addition, depending on the type of the tunnels supported (for example, manually configur… | |
| 1.3.6.1.2.1.10.166.3.3.1.2 | GroupmplsTunnelManualGroup | current | Object(s) needed to implement manually configured tunnels. | |
| 1.3.6.1.2.1.10.166.3.3.1.3 | GroupmplsTunnelSignaledGroup | current | Objects needed to implement signaled tunnels. | |
| 1.3.6.1.2.1.10.166.3.3.1.4 | GroupmplsTunnelScalarGroup | current | Scalar object needed to implement MPLS tunnels. | |
| 1.3.6.1.2.1.10.166.3.3.1.5 | GroupmplsTunnelIsIntfcGroup | current | Objects needed to implement tunnels that are interfaces. | |
| 1.3.6.1.2.1.10.166.3.3.1.6 | GroupmplsTunnelIsNotIntfcGroup | current | Objects needed to implement tunnels that are not interfaces. | |
| 1.3.6.1.2.1.10.166.3.3.1.7 | GroupmplsTunnelCRLDPResOptionalGroup | current | Set of objects implemented for resources applicable for tunnels signaled using CR-LDP. | |
| 1.3.6.1.2.1.10.166.3.3.1.8 | GroupmplsTeNotificationGroup | current | Set of notifications implemented in this module. None is mandatory. | |
| 1.3.6.1.2.1.10.166.3.3.2 | NodemplsTeCompliances | |||
| 1.3.6.1.2.1.10.166.3.3.2.1 | CompliancemplsTeModuleFullCompliance | current | Compliance statement for agents that provide full support the MPLS-TE-STD-MIB module. | |
| 1.3.6.1.2.1.10.166.3.3.2.2 | CompliancemplsTeModuleReadOnlyCompliance | read-only | current | Compliance requirement for implementations that only provide read-only support for MPLS-TE-STD-MIB. Such devices can then be monitored but cannot be configured… |