NETI-ETH-MIB
275 objects
Reference: NID2982 This MIB specifies objects for configuring Ethernet-like services and devices. It models trail termination points (TTPs) for Ethernet Transport Service as virtual interfaces. It also includes objects for configuration of the physical interfaces (ports). 1+1 protected transport is provided using virtual interfaces as interface groups. Physical and logical interfaces are connected to Forwarding Functions. The configuration model consists of the following primary tables: ethDeviceTable. This table contains one entry for every device (board). Its primary function is to provide capability information about the objects such as forwarding functions and interfaces on the device. ethIfTable. Table with all interfaces, both physical (dot3), logical (ETS), and virtual ports as interface group. The table contains an entry for every port. It contains configuration objects common to all port types. ethDot3Table. Table that contains an entry for every physical port. The table holds the data related to the physical port. Note that the port is also represented in the ethIfTable, and is referenced by the same index in both tables. ethEtsTable. Table that contains one entry for every Ethernet Transport Service Trail Termination Point (ETS TTP). A TTP is used to connect a port to a remote port using a connection over the DTM network. Note that the port is also represented in the ethIfTable, and is referenced by the same index in both tables. ethIfgTable. This table contains one entry for every interface group. An interface group is a virtual port that represents the transport over two paths to a remote interface group for 1+1 protected transport. The two paths are implemented using two ports from the ethEtsTable. ethFwdFuncTable. This table contains an entry for every forwarding function. Physical and ETS ports must be associated with a forwarding function. The forwarding function then forwards Ethernet frames between the different associated ports. Configuration objects on the forwarding function and the associated interfaces control how frames are forwarded to the different ports. In addition to the primary tables, there are some other tables: ethFwdDiffservTable. Configuration of differentiated service code points to flow group map for a forwarding function. ethIfQueueTable. Configuration of a port's queues. ethIfQDropThresholdTable. Configuration of drop thresholds for combination of traffic class and drop precedence per interface. ethIfVLANSetsTable. Configuration of a the port's VLAN membership. ethEtsTConnectionTable. References to connections that are terminating in a Trail Termination Point. ethEtsIndexLookupTable. Reverse-lookup of an entry in the ethEtsTable based on known DSTI. The following two tables contains information regarding the Rapid Spanning Tree Protocol: ethFwdRstpTable. The table contains data related to the bridge for the Rapid Spanning Tree Protocol. This table is indexed with the same index as the ethFwdTable. ethIfRstpTable. The table contains data related to the port for the Rapid Spanning Tree Protocol. This table is indexed with the same index as the ethIfTable (and ethDot3Table and ethEtsTable).
Imported Objects
| NETI-CHMGR-MIB | Dsti |
| NETI-COMMON-MIB | netiGeneric |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-SMI | Counter32 Counter64 Gauge32 Integer32 MODULE-IDENTITY OBJECT-TYPE TimeTicks Unsigned32 |
| SNMPv2-TC | RowPointer RowStatus TEXTUAL-CONVENTION TimeStamp TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.2928.2.2 | IdentitynetiEthMIB | Reference: NID2982 This MIB specifies objects for configuring Ethernet-like services and devices. It models trail termination points (TTPs) for Ethernet Transp… | ||
| 1.3.6.1.4.1.2928.2.2.1 | NodeethObjects | |||
| 1.3.6.1.4.1.2928.2.2.1.1 | NodeethDeviceGroup | |||
| 1.3.6.1.4.1.2928.2.2.1.1.1 | TableethDeviceTable | not-accessible | current | Table that represents Ethernet capable devices. The table is automatically populated with entries representing all mounted Ethernet devices. |
| 1.3.6.1.4.1.2928.2.2.1.1.1.1 | RowethDeviceEntry | not-accessible | current | An entry representing one device (board). |
| 1.3.6.1.4.1.2928.2.2.1.1.1.1.1 | ColumnethDevIndex | not-accessible | current | An index in the table. The index is equal to the board position in the node. The index is maintained across reboots of the managed system. |
| 1.3.6.1.4.1.2928.2.2.1.1.1.1.2 | ColumnethDevRowStatus | read-write | current | The following values are supported: active(1). The object always reads active. destroy(6). All configurations for the device are deleted. If the physical devic… |
| 1.3.6.1.4.1.2928.2.2.1.1.1.1.3 | ColumnethDevName | read-only | current | The textual name of the device. The value of this object should be the name of the device as assigned by the local device and should be suitable for use in com… |
| 1.3.6.1.4.1.2928.2.2.1.1.1.1.4 | ColumnethDevContainerName | read-only | current | The name of the container where the physical device is mounted. |
| 1.3.6.1.4.1.2928.2.2.1.1.1.1.5 | ColumnethDevProductName | read-only | current | The name of the product. The value of this object should be the name of the device as printed on the front panel or similar. |
| 1.3.6.1.4.1.2928.2.2.1.1.1.1.6 | ColumnethDevStatus | read-only | current | The status of the device, indicating if the board is plugged in or not. present(1). The device is present and functional. absent(2). The device is not present.… |
| 1.3.6.1.4.1.2928.2.2.1.1.1.1.7 | ColumnethDevCapJumboFrames | read-only | current | The Jumbo Frames capabilities of forwarding functions on the device. Describes all supported values of the Jumbo Frames setting. See ethFwdJumboFrames. |
| 1.3.6.1.4.1.2928.2.2.1.1.1.1.8 | ColumnethDevCapMaxAgingTime | read-only | current | The maximum aging time for dynamically learned forwarding information for forwarding functions on the device. Zero (0) if the device does not allow the value t… |
| 1.3.6.1.4.1.2928.2.2.1.1.1.1.9 | ColumnethDevCapMACMode | read-only | current | The MAC mode capabilities of forwarding functions on the device. Describes all supported values of the MAC modes setting. See ethFwdMACMode. |
| 1.3.6.1.4.1.2928.2.2.1.1.1.1.10 | ColumnethDevCapSpanningTree | read-only | current | The spanning tree capabilities of forwarding functions on the device. Describes all supported values of the spanning tree settings. If spanning tree is not sup… |
| 1.3.6.1.4.1.2928.2.2.1.1.1.1.11 | ColumnethDevCapVLANMode | read-only | current | The VLAN mode capabilities of forwarding functions on the device. Describes all supported values of the VLAN mode settings. See ethFwdVLANMode. |
| 1.3.6.1.4.1.2928.2.2.1.1.1.1.12 | ColumnethDevCapAdvertisedDuplex | read-only | current | Supported values for the duplex setting of a physical interface on the device. See dot3AdvertisedDuplex. |
| 1.3.6.1.4.1.2928.2.2.1.1.1.1.13 | ColumnethDevCapAdvertisedFlowControl | read-only | current | Supported values for the flow control setting of a physical interface on the device. See dot3AdvertisedFlowControl. |
| 1.3.6.1.4.1.2928.2.2.1.1.1.1.14 | ColumnethDevCapAcceptableFrameType | read-only | current | The frame types capabilities of interfaces on the device. Describes all supported values of the acceptable frame type setting. See ethIfAcceptableFrameTypes. |
| 1.3.6.1.4.1.2928.2.2.1.1.1.1.15 | ColumnethDevCapDefaultEthernetPriority | read-only | current | The range of allowed values for Ethernet priority of interfaces on the device. See ethIfDefaultEthernetPriority. The object consists of two octets, where the f… |
| 1.3.6.1.4.1.2928.2.2.1.1.1.1.16 | ColumnethDevCapLearning | read-only | current | The learning capabilities of forwarding functions on the device. Describes all supported values of the learning setting. See ethIfLearning. |
| 1.3.6.1.4.1.2928.2.2.1.1.1.1.17 | ColumnethDevCapTransmittedFrameTypeETS | read-only | current | The allowed values of the transmitted frame type on an Ethernet Transport Service Trail Termination Point, ETS TTP. See ethIfTransmittedFrameType. Note that th… |
| 1.3.6.1.4.1.2928.2.2.1.1.1.1.18 | ColumnethDevCapTransmittedFrameTypeDot3 | read-only | current | The allowed values of the transmitted frame type on an dot3 interface. See ethIfTransmittedFrameType. Note that the interface type can be determined by examine… |
| 1.3.6.1.4.1.2928.2.2.1.1.1.1.19 | ColumnethDevCapMaxMaxQueueOctets | read-only | current | The maximum value in octets possible to set for the maximum queue size for queues on the device. See ethIfQueueMaxOctets. |
| 1.3.6.1.4.1.2928.2.2.1.1.1.1.20 | ColumnethDevCapMaxMaxQueueFrames | read-only | deprecated | The maximum value in frames allowed to set for the maximum queue size for queues on the device. See ethIfQueueMaxFrames. |
| 1.3.6.1.4.1.2928.2.2.1.1.1.1.21 | ColumnethDevCapMaxTrafficClass | read-only | current | The maximum number of traffic classes supported by the device. Traffic classes are identified by numbers starting from 0 to, but not including, this value. |
| 1.3.6.1.4.1.2928.2.2.1.1.1.1.22 | ColumnethDevEtsNextIndex | read-only | current | The value of the next available index (ethIfIndex) in the ethEtsTable for this device. |
| 1.3.6.1.4.1.2928.2.2.1.1.1.1.23 | ColumnethDevFwdFuncNextIndex | read-only | current | The value of the next available index (ethFwdIndex) in the ethFwdFuncTable for this device. |
| 1.3.6.1.4.1.2928.2.2.1.1.1.1.24 | ColumnethDevCapPerformanceMonitoring | read-only | current | Indicates how the device supports performance monitoring. |
| 1.3.6.1.4.1.2928.2.2.1.1.1.1.25 | ColumnethDevCapConfigurableFaultMgmt | read-only | current | Indicates how the device supports configurable fault management. |
| 1.3.6.1.4.1.2928.2.2.1.1.1.1.26 | ColumnethDevIfgFirstIndex | read-only | current | The value of the first allowed index (ethIfIndex) in the ethIfgTable for this device. |
| 1.3.6.1.4.1.2928.2.2.1.1.1.1.27 | ColumnethDevIfgNextIndex | read-only | current | The value of the next available index (ethIfIndex) in the ethIfgTable for this device. |
| 1.3.6.1.4.1.2928.2.2.1.1.1.1.28 | ColumnethDevCapDropPrecedenceLevels | read-only | current | The number of different drop precedence (DP) levels that this devices supports. The DP levels are numbered from 0 to (dropPrecedenceLevels - 1) |
| 1.3.6.1.4.1.2928.2.2.1.1.1.1.29 | ColumnethDevCapDropProbabilityFunctions | read-only | current | The drop probability functions supported for this device. |
| 1.3.6.1.4.1.2928.2.2.1.1.1.1.30 | ColumnethDevFailure | read-only | current | A string describing the configuration or error status of the device. The string is the empty string if the configuration is correct, otherwise a message descri… |
| 1.3.6.1.4.1.2928.2.2.1.2 | NodeethFwdFuncGroup | |||
| 1.3.6.1.4.1.2928.2.2.1.2.1 | ScalarethFwdFuncLastChange | read-only | current | The value of sysUpTime when status or configuration of any the objects in the ethFwdFuncTable or ethFwdDiffservTable was last changed. |
| 1.3.6.1.4.1.2928.2.2.1.2.2 | TableethFwdFuncTable | not-accessible | current | Table of forwarding functions. |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1 | RowethFwdFuncEntry | not-accessible | current | An entry representing one forwarding function. |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1.1 | ColumnethFwdIndex | not-accessible | current | An index representing the forwarding function on the device. |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1.2 | ColumnethFwdRowStatus | read-create | current | See SNMPv2-TC. The maximum number of forwarding functions is limited by the type of device. This is described per device in ethDevCapMaxForwardingFunctions. Th… |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1.3 | ColumnethFwdName | read-only | current | The textual name of the forwarding function. The value of this object should be suitable for use in commands entered at the device's `console'. |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1.4 | ColumnethFwdCustomerId | read-create | current | An identification number representing the customer or user using the forwarding function. The value could be used for e.g. Charge Data Records. The value zero … |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1.5 | ColumnethFwdPurpose | read-create | current | A string representing the purpose of the forwarding function. The string is for administrative purpose. |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1.6 | ColumnethFwdJumboFrames | read-write | current | Specifies how the forwarding function shall handle Jumbo frames: on(1). Jumbo frames are forwarded as any standard Ethernet frame. off(2). Jumbo frames are dis… |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1.7 | ColumnethFwdMACMode | read-write | current | Specifies how the forwarding function shall handle unicast frames when it does not know what interface to use for reaching a destination. auto(1). Equivalent t… |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1.8 | ColumnethFwdCurrentMACMode | read-only | current | Describes the currently active MAC mode, see ethFwdMACMode. |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1.9 | ColumnethFwdSpanningTree | read-write | current | auto(1). If the device does not implement the spanning-tree protocol, or if exactly two interfaces are connected to the forwarding function, then it will act a… |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1.10 | ColumnethFwdVLANMode | read-write | current | transparent(1). Ignore VLAN tags on received frames. VLAN tags are not added nor removed from the frames. If a frame has a VLAN tag, then it is retained. If a … |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1.11 | ColumnethFwdAgingTime | read-write | current | The timeout period in seconds for aging out dynamically learned forwarding information. The value 0 means that aging is disabled and that the learned entries a… |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1.12 | ColumnethFwdFailure | read-only | current | A string describing the configuration or error status of the forwarding function. The string is the empty string if the configuration is correct, otherwise a m… |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1.13 | ColumnethFwdLastChange | read-only | current | The value of sysUpTime at the time when the operational state or any configuration was last changed on this forwarding function. |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1.14 | ColumnethFwdPropagateFaults | read-write | current | Propagate faults to all interfaces belonging to this forwarding function. |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1.15 | ColumnethFwdReservedAddr0180C2000002 | read-write | current | Configuration of how to process reserved MAC address. |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1.16 | ColumnethFwdReservedAddr0180C2000003 | read-write | current | Configuration of how to process reserved MAC address. |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1.17 | ColumnethFwdReservedAddr0180C2000004 | read-write | current | Configuration of how to process reserved MAC address. |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1.18 | ColumnethFwdReservedAddr0180C2000005 | read-write | current | Configuration of how to process reserved MAC address. |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1.19 | ColumnethFwdReservedAddr0180C2000006 | read-write | current | Configuration of how to process reserved MAC address. |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1.20 | ColumnethFwdReservedAddr0180C2000007 | read-write | current | Configuration of how to process reserved MAC address. |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1.21 | ColumnethFwdReservedAddr0180C2000008 | read-write | current | Configuration of how to process reserved MAC address. |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1.22 | ColumnethFwdReservedAddr0180C2000009 | read-write | current | Configuration of how to process reserved MAC address. |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1.23 | ColumnethFwdReservedAddr0180C200000A | read-write | current | Configuration of how to process reserved MAC address. |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1.24 | ColumnethFwdReservedAddr0180C200000B | read-write | current | Configuration of how to process reserved MAC address. |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1.25 | ColumnethFwdReservedAddr0180C200000C | read-write | current | Configuration of how to process reserved MAC address. |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1.26 | ColumnethFwdReservedAddr0180C200000D | read-write | current | Configuration of how to process reserved MAC address. |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1.27 | ColumnethFwdReservedAddr0180C200000E | read-write | current | Configuration of how to process reserved MAC address. |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1.28 | ColumnethFwdReservedAddr0180C200000F | read-write | current | Configuration of how to process reserved MAC address. |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1.29 | ColumnethFwdCurrentStpMode | read-only | current | Indicates the current STP mode as, as a result of the configured value in ethFwdSpanningTree. Unless ethFwdSpannigTree is `auto(1), then this always reads the … |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1.30 | ColumnethFwdMrpAddr0180C2000020 | read-write | current | Configuration of how to process Multiple Registration Protocol (MRP) MAC address. |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1.31 | ColumnethFwdMrpAddr0180C2000021 | read-write | current | Configuration of how to process Multiple Registration Protocol (MRP) MAC address. |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1.32 | ColumnethFwdMrpAddr0180C2000022 | read-write | current | Configuration of how to process Multiple Registration Protocol (MRP) MAC address. |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1.33 | ColumnethFwdMrpAddr0180C2000023 | read-write | current | Configuration of how to process Multiple Registration Protocol (MRP) MAC address. |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1.34 | ColumnethFwdMrpAddr0180C2000024 | read-write | current | Configuration of how to process Multiple Registration Protocol (MRP) MAC address. |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1.35 | ColumnethFwdMrpAddr0180C2000025 | read-write | current | Configuration of how to process Multiple Registration Protocol (MRP) MAC address. |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1.36 | ColumnethFwdMrpAddr0180C2000026 | read-write | current | Configuration of how to process Multiple Registration Protocol (MRP) MAC address. |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1.37 | ColumnethFwdMrpAddr0180C2000027 | read-write | current | Configuration of how to process Multiple Registration Protocol (MRP) MAC address. |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1.38 | ColumnethFwdMrpAddr0180C2000028 | read-write | current | Configuration of how to process Multiple Registration Protocol (MRP) MAC address. |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1.39 | ColumnethFwdMrpAddr0180C2000029 | read-write | current | Configuration of how to process Multiple Registration Protocol (MRP) MAC address. |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1.40 | ColumnethFwdMrpAddr0180C200002A | read-write | current | Configuration of how to process Multiple Registration Protocol (MRP) MAC address. |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1.41 | ColumnethFwdMrpAddr0180C200002B | read-write | current | Configuration of how to process Multiple Registration Protocol (MRP) MAC address. |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1.42 | ColumnethFwdMrpAddr0180C200002C | read-write | current | Configuration of how to process Multiple Registration Protocol (MRP) MAC address. |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1.43 | ColumnethFwdMrpAddr0180C200002D | read-write | current | Configuration of how to process Multiple Registration Protocol (MRP) MAC address. |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1.44 | ColumnethFwdMrpAddr0180C200002E | read-write | current | Configuration of how to process Multiple Registration Protocol (MRP) MAC address. |
| 1.3.6.1.4.1.2928.2.2.1.2.2.1.45 | ColumnethFwdMrpAddr0180C200002F | read-write | current | Configuration of how to process Multiple Registration Protocol (MRP) MAC address. |
| 1.3.6.1.4.1.2928.2.2.1.2.3 | TableethFwdDiffservTable | not-accessible | current | The table maps differentiated service code points (DSCP) to flow groups. |
| 1.3.6.1.4.1.2928.2.2.1.2.3.1 | RowethFwdDiffservEntry | not-accessible | current | An entry represents the mapping of one DSCP to one flow group for an interface. |
| 1.3.6.1.4.1.2928.2.2.1.2.3.1.1 | ColumnethFwdDiffservIndex | not-accessible | current | An index representing the differentiated service code point (DSCP). For each forwarding function, the table contains 64 rows, numbered from 0 to 63 representin… |
| 1.3.6.1.4.1.2928.2.2.1.2.3.1.2 | ColumnethFwdDiffservFlowGroup | read-write | current | Specifies which flow group that the differentiated service code point (DSCP) shall be mapped to. |
| 1.3.6.1.4.1.2928.2.2.1.2.4 | TableethFwdRstpTable | not-accessible | current | The table contains Rapid Spanning Tree Protocol (RSTP) specific configurations and data for forwarding functions. If a forwarding function does not support RST… |
| 1.3.6.1.4.1.2928.2.2.1.2.4.1 | RowethFwdRstpEntry | not-accessible | current | An entry represents Rapid Spanning Tree Protocol (RSTP) related data for one forwarding function. |
| 1.3.6.1.4.1.2928.2.2.1.2.4.1.1 | ColumnethFwdRstpBridgeIdentifier | read-only | current | The unique identifier for this bridge. |
| 1.3.6.1.4.1.2928.2.2.1.2.4.1.2 | ColumnethFwdRstpPriority | read-write | current | The local bridge priority. The value must be set in increments of 4096. |
| 1.3.6.1.4.1.2928.2.2.1.2.4.1.3 | ColumnethFwdRstpTimeSinceTopologyChange | read-only | current | The time in 1/100 seconds since the last topology change. |
| 1.3.6.1.4.1.2928.2.2.1.2.4.1.4 | ColumnethFwdRstpTopologyChangeCount | read-only | current | The total number of topology changes detected by this bridge since the management entity was last reset or initialized. |
| 1.3.6.1.4.1.2928.2.2.1.2.4.1.5 | ColumnethFwdRstpTopologyChange | read-only | current | Set to `true(1)' when a topology change is in progress. |
| 1.3.6.1.4.1.2928.2.2.1.2.4.1.6 | ColumnethFwdRstpDesignatedRoot | read-only | current | The bridge identifier of the root of the spanning tree, as determined by the Spanning Tree Protocol, as executed by this bridge. This value is used as the Root… |
| 1.3.6.1.4.1.2928.2.2.1.2.4.1.7 | ColumnethFwdRstpRootPathCost | read-only | current | The cost of the path to the root as seen from this bridge. |
| 1.3.6.1.4.1.2928.2.2.1.2.4.1.8 | ColumnethFwdRstpRootPortName | read-only | current | The name of the interface that offers the lowest cost path from this bridge to the root bridge. |
| 1.3.6.1.4.1.2928.2.2.1.2.4.1.9 | ColumnethFwdRstpMaxAge | read-only | current | The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is … |
| 1.3.6.1.4.1.2928.2.2.1.2.4.1.10 | ColumnethFwdRstpHelloTime | read-only | current | The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree, or trying to become… |
| 1.3.6.1.4.1.2928.2.2.1.2.4.1.11 | ColumnethFwdRstpForwardDelay | read-only | current | The root bridge forward delay parameter, in units of hundredths of a second. |
| 1.3.6.1.4.1.2928.2.2.1.2.4.1.12 | ColumnethFwdRstpBridgeMaxAge | read-write | current | The value that all bridges use for MaxAge when this bridge is acting as the root. An agent may return a badValue error if a set is attempted to a value that is… |
| 1.3.6.1.4.1.2928.2.2.1.2.4.1.13 | ColumnethFwdRstpBridgeHelloTime | read-write | current | The value that all bridges use for HelloTime when this bridge is acting as the root. An agent may return a badValue error if a set is attempted to a value that… |
| 1.3.6.1.4.1.2928.2.2.1.2.4.1.14 | ColumnethFwdRstpBridgeForwardDelay | read-write | current | The value that all bridges use for ForwardDelay when this bridge is acting as the root. An agent may return a badValue error if a set is attempted to a value t… |
| 1.3.6.1.4.1.2928.2.2.1.2.4.1.15 | ColumnethFwdRstpTxHoldCount | read-write | current | The local bridge transmit hold count parameter. |
| 1.3.6.1.4.1.2928.2.2.1.2.4.1.16 | ColumnethFwdRstpForceVersion | read-write | current | Force the spanning tree protocol version to use for this bridge: stp(1). STP compatibility mode. Causes an RSTP Bridge to use STP compatible BPDUs and timer va… |
| 1.3.6.1.4.1.2928.2.2.1.3 | NodeethInterfaceGroup | |||
| 1.3.6.1.4.1.2928.2.2.1.3.1 | ScalarethIfGroupLastChange | read-only | current | The value of sysUpTime when status or configuration of any the objects in this group was last changed. |
| 1.3.6.1.4.1.2928.2.2.1.3.2 | TableethIfTable | not-accessible | current | Table containing all interfaces, both physical, logical for use with Ethernet Transport Service, and interface groups for use with 1+1 protection. |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1 | RowethIfEntry | not-accessible | current | An entry representing one interface or interface group. If the interface is a physical interface, a conceptual row also exists for the interface in the ethDot3… |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.1 | ColumnethIfIndex | not-accessible | current | An index for the interface. The index is maintained across restarts of the managed system. The management system may require that the value of this object is w… |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.2 | ColumnethIfIfIndex | read-only | current | This variable uniquely identifies the interface in the ifTable. The value is 0 if the interface is not present in the ifTable. |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.3 | ColumnethIfName | read-only | current | The name of the interface. If the interface is a physical interface, it is named `eth<device>:<port>' where <device> is the value of ethDevIndex, and <port> is… |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.4 | ColumnethIfType | read-only | current | The type of interface. The value `unknown(1)' is presented if required hardware is missing, or if it otherwise is not possible to determined the type of interf… |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.5 | ColumnethIfCustomerId | read-write | current | An identification number representing the customer or user using the interface. The value could be used for e.g. Charge Data Records. The value zero (0) indica… |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.6 | ColumnethIfPurpose | read-write | current | A string representing the purpose of the interface. The string is for administrative purpose. |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.7 | ColumnethIfAdminStatus | read-write | current | The administrative state of the interface. If the interface represents a Ethernet Transport Service Trail Termination Point (ETS TTP), then the variable contro… |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.8 | ColumnethIfOperStatus | read-only | current | The actual operational state of the interface. The value should normally follow the administrative state (ethIfAdminStatus). up(1). The interface is up and ope… |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.9 | ColumnethIfFailure | read-only | current | A string describing the configuration or error status of the interface. The string is the empty string if the configuration is correct, otherwise a message des… |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.10 | ColumnethIfForwardingFunction | read-write | current | The index (ethFwdIndex) in the ethFwdFuncTable of the forwarding function that this interface belongs to. The value -1 denotes that the interface does not belo… |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.11 | ColumnethIfAcceptableFrameTypes | read-write | current | all(1). All frames, regardless of whether they have a VLAN tag or not, shall be accepted. vlanTagged(2). Only frames that contain a non-zero VLAN id in the VLA… |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.12 | ColumnethIfTransmittedFrameType | read-write | current | vlanTagged(2). Forwarded frames are tagged according to setting on ethFwdVLANMode. untagged(3). VLAN tags on forwarded frames are removed according to setting … |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.13 | ColumnethIfDefaultVLAN | read-write | current | If an untagged frame is received on this interface, it will be tagged with a VLAN having a VLAN id as specified in this variable. The VLAN tag will be a custom… |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.14 | ColumnethIfDefaultEthernetPriority | read-write | current | Specifies the Ethernet priority assigned to a frame that has arrived via this port, and that does not have a VLAN tag. Priority will only be assigned to the fr… |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.15 | ColumnethIfPriorityMode | read-write | current | Selects the method to use when assigning a flow group to a frame that arrives via this interface: ethernet(1). The user bits are used. diffserv(2). The differe… |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.16 | ColumnethIfDefaultTrafficClass | read-write | current | Frames that do have any priority information are assigned this traffic class. See ethDevCapMaxTrafficClass for max value supported by the device. |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.17 | ColumnethIfFlowGroupMap | read-write | current | Represents a flow group to traffic class map. The octet string consists of eight octets, one for each flow group. The position in the string represents the flo… |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.18 | ColumnethIfLearning | read-write | current | Specifies if MAC learning is enabled on the interface. on(1). MAC learning is enabled. The forwarding function learns what interface to use for a destination b… |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.19 | ColumnethIfInSpeed | read-only | current | An estimate of the interface's current input bandwidth in bits per second. If the interface is a physical interface (represented in ethDot3Table), then this va… |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.20 | ColumnethIfInHighSpeed | read-only | current | An estimate of the interface's current input bandwidth in units of 1,000,000 bits per second. If this object reports a value of `n' then the speed of the inter… |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.21 | ColumnethIfOutSpeed | read-only | current | An estimate of the interface's current output bandwidth in bits per second. If the interface is a physical interface (represented in ethDot3Table), then this v… |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.22 | ColumnethIfOutHighSpeed | read-only | current | An estimate of the interface's current output bandwidth in units of 1,000,000 bits per second. If this object reports a value of `n' then the speed of the inte… |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.23 | ColumnethIfVLANNextIndex | read-only | current | Next available value of ethIfVLANSetIndex in ethIfVLANSetTable for this interface. |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.24 | ColumnethIfLastChange | read-only | current | The value of sysUpTime at the time when the operational state or any configuration was last changed on this interface. |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.25 | ColumnethIfSrcPmReference | read-only | current | A reference to an object that presents performance data for the source side of the interface. The object is not part of this MIB. |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.26 | ColumnethIfSnkPmReference | read-only | current | A reference to an object that presents performance data for the sink side of the interface. The object is not part of this MIB. |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.27 | ColumnethIfSrcDegThreshold | read-write | current | Threshold in number of dropped frames per second for generating a degraded second. A degraded second is generated when the number of dropped frames are equal o… |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.28 | ColumnethIfSnkDegThreshold | read-write | current | Threshold in number of dropped frames per second for generating a degraded second. A degraded second is generated when the number of dropped frames are equal o… |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.29 | ColumnethIfSrcDegPeriod | read-write | current | Number of consecutive bad seconds that are needed for generating degraded signal alarm and/or AIS. |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.30 | ColumnethIfSnkDegPeriod | read-write | current | Number of consecutive bad seconds that are needed for generating degraded signal alarm and/or AIS. |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.31 | ColumnethIfSrcReducedBitRateThreshold | read-write | current | Reduced Bit Rate threshold in bits per second that is needed for generating a major alarm and/or AIS. If the threshold for the interface is greater than the ma… |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.32 | ColumnethIfSnkReducedBitRateThreshold | read-write | current | Reduced Bit Rate threshold in bits per second that is needed for generating a major alarm and/or AIS. If the threshold for the interface is greater than the ma… |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.33 | ColumnethIfSrcReducedBitRateHighThreshold | read-write | current | Reduced Bit Rate threshold in 1,000,000 bits per second that is needed for generating a major alarm and/or AIS. If this object reports a value of `n' then the … |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.34 | ColumnethIfSnkReducedBitRateHighThreshold | read-write | current | Reduced Bit Rate threshold in 1,000,000 bits per second that is needed for generating a major alarm and/or AIS. If this object reports a value of `n' then the … |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.35 | ColumnethIfSrcReducedBitRateAIS | read-write | current | Defines if Reduced Bit Rate signal shall result in generation of AIS. |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.36 | ColumnethIfSnkReducedBitRateAIS | read-write | current | Defines if Reduced Bit Rate signal shall result in generation of AIS. |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.37 | ColumnethIfSnkDegAIS | read-write | current | Defines if degraded signal on the sink interface shall result in generation of AIS. |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.38 | ColumnethIfSrcMinorReducedBitRateThreshold | read-write | current | Reduced Bit Rate threshold in bits per second that is needed for generating a minor alarm. If the threshold for the interface is greater than the maximum value… |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.39 | ColumnethIfSnkMinorReducedBitRateThreshold | read-write | current | Reduced Bit Rate threshold in bits per second that is needed for generating a minor alarm. If the threshold for the interface is greater than the maximum value… |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.40 | ColumnethIfSrcMinorReducedBitRateHighThreshold | read-write | current | Reduced Bit Rate threshold in 1,000,000 bits per second that is needed for generating a minor alarm. If this object reports a value of `n' then the threshold v… |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.41 | ColumnethIfSnkMinorReducedBitRateHighThreshold | read-write | current | Reduced Bit Rate threshold in 1,000,000 bits per second that is needed for generating a minor alarm. If this object reports a value of `n' then the threshold v… |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.42 | ColumnethIfSrcFailure | read-only | current | A string describing the configuration or error status of the source sub-interface. The string is the empty string if the configuration is correct, otherwise a … |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.43 | ColumnethIfSnkFailure | read-only | current | A string describing the configuration or error status of the sink sub-interface. The string is the empty string if the configuration is correct, otherwise a me… |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.44 | ColumnethIfInterfaceGroup | read-write | current | The index (ethIfIndex) in the ethIfTable of the interface group that this interface belongs to. The value -1 denotes that the interface does not belong to an i… |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.45 | ColumnethIfMaxMaxQueueFrames | read-only | current | The maximum allowed value for the maximum queue size for queues on the interface, ethIfQueueMaxFrames. |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.46 | ColumnethIfDefaultDropPrecedence | read-write | current | Frames that do have any priority information are assigned this drop precedence (DP). The drop precedence must be in the range 0 to (ethDevCapDropPrecedenceLeve… |
| 1.3.6.1.4.1.2928.2.2.1.3.2.1.47 | ColumnethIfDropPrecedenceMap | read-write | current | Represents a flow group to drop precedence (DP) map. The octet string consists of eight octets, one for each flow group. The position in the string represents … |
| 1.3.6.1.4.1.2928.2.2.1.3.3 | TableethIfQueueTable | not-accessible | current | Queues, one queue per interface and traffic class. |
| 1.3.6.1.4.1.2928.2.2.1.3.3.1 | RowethIfQueueEntry | not-accessible | current | An entry representing one queue. |
| 1.3.6.1.4.1.2928.2.2.1.3.3.1.1 | ColumnethIfQueueTrafficClass | not-accessible | current | Traffic class representing the queue. The index ranges from 0 to the max number of traffic classes - 1. See ethDevCapMaxTrafficClass for max value supported by… |
| 1.3.6.1.4.1.2928.2.2.1.3.3.1.2 | ColumnethIfQueueMaxOctets | read-write | current | The maximum number of octets that can be queued for input on the interface and traffic class. If an arriving frame is too large to fit into the queue, the fram… |
| 1.3.6.1.4.1.2928.2.2.1.3.3.1.3 | ColumnethIfQueueMaxFrames | read-write | current | The maximum number of frames that can be queued for input on the interface and traffic class. A setting of 0 means that queuing is disabled and frames destined… |
| 1.3.6.1.4.1.2928.2.2.1.3.4 | TableethIfVLANSetsTable | not-accessible | current | A table with VLAN sets. An interface belongs to the VLANs described by the union of all VLAN ids specified in all VLAN sets for the interface. Is possible to d… |
| 1.3.6.1.4.1.2928.2.2.1.3.4.1 | RowethIfVLANSetsEntry | not-accessible | current | Represents a VLAN set. A VLAN set represents a list of VLAN ids that an interface shall belong to. |
| 1.3.6.1.4.1.2928.2.2.1.3.4.1.1 | ColumnethIfVLANSetIndex | not-accessible | current | An index representing the VLAN set. |
| 1.3.6.1.4.1.2928.2.2.1.3.4.1.2 | ColumnethIfVLANRowStatus | read-create | current | See SNMPv2-TC. The following values are supported: active(1). The object always reads active. createAndGo(4). A new conceptual row is created representing a ne… |
| 1.3.6.1.4.1.2928.2.2.1.3.4.1.3 | ColumnethIfVLANSet | read-create | current | A set of VLAN ids that the interface belongs to. |
| 1.3.6.1.4.1.2928.2.2.1.3.4.1.4 | ColumnethIfVLANCustomerId | read-create | current | An identification number representing the customer or user using the VLAN set. The value could be used for e.g. Charge Data Records. The value zero (0) indicat… |
| 1.3.6.1.4.1.2928.2.2.1.3.4.1.5 | ColumnethIfVLANPurpose | read-create | current | A string representing the purpose of the VLAN set. The string is for administrative purpose. |
| 1.3.6.1.4.1.2928.2.2.1.3.5 | TableethDot3Table | not-accessible | current | Table that contains representations of physical interfaces. |
| 1.3.6.1.4.1.2928.2.2.1.3.5.1 | RowethDot3Entry | not-accessible | current | An entry representing one physical interface. For each conceptual row in this table, a conceptual row with the same index exists in the interface base table et… |
| 1.3.6.1.4.1.2928.2.2.1.3.5.1.1 | ColumnethDot3AutoNegotiate | read-write | current | Controls the desired value of auto-negotiation: true(1). Auto-negotiation shall be enabled. If the interface does not allow auto-negotiation, then this object … |
| 1.3.6.1.4.1.2928.2.2.1.3.5.1.2 | ColumnethDot3AdvertisedSpeed | read-write | current | The link speeds that the interface shall advertise that it supports. If auto-negotiation is disabled, then use the highest set link speed. |
| 1.3.6.1.4.1.2928.2.2.1.3.5.1.3 | ColumnethDot3AdvertisedDuplex | read-write | current | The duplex settings that the interface shall advertise that it supports. See ethDevCapAdvertisedDuplex for allowed duplex settings on the device. |
| 1.3.6.1.4.1.2928.2.2.1.3.5.1.4 | ColumnethDot3AdvertisedFlowControl | read-write | current | The flow control settings that the interface shall advertise that it supports. If auto-negotiation is disabled (ethDot3SAutoNegotiate), then this object descri… |
| 1.3.6.1.4.1.2928.2.2.1.3.5.1.5 | ColumnethDot3ActiveSpeed | read-only | current | The active links speed in Mbps. |
| 1.3.6.1.4.1.2928.2.2.1.3.5.1.6 | ColumnethDot3ActiveDuplex | read-only | current | The active link duplex. If the interface is down, then `notApplicable(3)' is presented. |
| 1.3.6.1.4.1.2928.2.2.1.3.5.1.7 | ColumnethDot3ActiveFlowControl | read-only | current | The active link flow control. If the interface is down, then `notApplicable(5)' is presented. |
| 1.3.6.1.4.1.2928.2.2.1.3.5.1.8 | ColumnethDot3ForceVLANTagged | read-write | current | Specifies a set of VLAN ids for which frames shall be forwarded with a tag although ethIfTransmittedFrameType is set to `untagged(3)'. The setting of this vari… |
| 1.3.6.1.4.1.2928.2.2.1.3.5.1.9 | ColumnethDot3ForceVLANUntagged | read-write | current | Specifies a set of VLAN ids for which frames shall be forwarded without a tag although ethIfTransmittedFrameType is set to `vlanTagged(2)'. The setting of this… |
| 1.3.6.1.4.1.2928.2.2.1.3.5.1.10 | ColumnethDot3SupportedSpeeds | read-only | current | All supported speeds for ethDot3AdvertisedSpeed. Note that this value depends on the SFP. |
| 1.3.6.1.4.1.2928.2.2.1.3.5.1.11 | ColumnethDot3ResetToDefaults | read-write | current | Writing a zero (0) resets all the the settings on the interface to its default values. |
| 1.3.6.1.4.1.2928.2.2.1.3.5.1.12 | ColumnethDot3AutoNegotiateStatus | read-only | current | Indicates if auto-negotiation is enabled or not. |
| 1.3.6.1.4.1.2928.2.2.1.3.5.1.13 | ColumnethDot3AutoNegotiateAllowed | read-only | current | Indicates if auto-negotiation is permitted with the current combination of interface type and speed. |
| 1.3.6.1.4.1.2928.2.2.1.3.5.1.14 | ColumnethDot3AutoNegotiateMandatory | read-only | current | Indicates if auto-negotiation is required with the current combination of interface type and speed. |
| 1.3.6.1.4.1.2928.2.2.1.3.5.1.15 | ColumnethDot3SupportedIfType | read-only | current | All supported interface types on the interface. This denotes what can be set on ethDot3SelectedIfType. Note that this value depends on the SFP. |
| 1.3.6.1.4.1.2928.2.2.1.3.5.1.16 | ColumnethDot3SelectedIfType | read-write | current | Selected interface speed. A selected value of `auto(0)' means that the interface type with the highest available line speed will be used. See ethIfType for the… |
| 1.3.6.1.4.1.2928.2.2.1.3.6 | TableethEtsTable | not-accessible | current | Table that contains definitions of Trail Termination Points (TTPs) for Ethernet Transport Service. For every row in the table, a corresponding row exists in th… |
| 1.3.6.1.4.1.2928.2.2.1.3.6.1 | RowethEtsEntry | not-accessible | current | An entry representing one ETS TTP. |
| 1.3.6.1.4.1.2928.2.2.1.3.6.1.1 | ColumnethEtsRowStatus | read-create | current | See SNMPv2-TC. The following values are supported: active(1). The object always reads active. createAndGo(4). A new conceptual row is created representing a ne… |
| 1.3.6.1.4.1.2928.2.2.1.3.6.1.2 | ColumnethEtsMode | read-create | current | Specifies whether the ETS TTP shall establish unicast or multicast connection. |
| 1.3.6.1.4.1.2928.2.2.1.3.6.1.3 | ColumnethEtsLocalDsti | read-create | current | The DSTI (DTM Service Type Instance) for the local application implementing the service. A valid value is automatically assigned when the conceptual row is cre… |
| 1.3.6.1.4.1.2928.2.2.1.3.6.1.4 | ColumnethEtsODescription | read-only | current | A reference to the corresponding description of the connection in the chmgrODescriptionTable in the Channel Manager MIB (NETI-CHMGR-MIB). The value is the inde… |
| 1.3.6.1.4.1.2928.2.2.1.3.6.1.5 | ColumnethEtsOConnection | read-only | current | A reference to the corresponding originating connection in the table chmgrOConnectionTable in the Channel Manager MIB (NETI-CHMGR-MIB). When an originating con… |
| 1.3.6.1.4.1.2928.2.2.1.3.6.1.6 | ColumnethEtsSnkExpectChannel | read-write | current | Controls whether a channel is expected to be terminated on this ETS TTP or not. This value can only be set if the mode (ethEtsMode) is multicast. true(1). A ch… |
| 1.3.6.1.4.1.2928.2.2.1.3.7 | TableethEtsTConnectionTable | not-accessible | current | Table that holds references to terminating connections for a ETS trail termination point. A trail termination point can terminate only one connection if a unic… |
| 1.3.6.1.4.1.2928.2.2.1.3.7.1 | RowethEtsTConnectionEntry | not-accessible | current | An entry representing the reference to one terminating connection. |
| 1.3.6.1.4.1.2928.2.2.1.3.7.1.1 | ColumnethEtsTConnectionIndex | not-accessible | current | The index representing one terminating connection for the trail terminating point. If the trail terminating point is unicast, the value of the index is always … |
| 1.3.6.1.4.1.2928.2.2.1.3.7.1.2 | ColumnethEtsTConnectionRowStatus | read-write | current | Row status according to SNMPv2-TC. It is only possible to delete rows. Rows are created by the application. If a row is deleted that represents an active conne… |
| 1.3.6.1.4.1.2928.2.2.1.3.7.1.3 | ColumnethEtsTConnection | read-only | current | A reference to the corresponding terminating connection in the table chmgrTConnectionTable in the Channel Manager MIB (NETI-CHMGR-MIB). When a connection is te… |
| 1.3.6.1.4.1.2928.2.2.1.3.8 | TableethEtsIndexLookupTable | not-accessible | current | Table to lookup the index in the ethEtsTable, corresponding to a specific DSTI. |
| 1.3.6.1.4.1.2928.2.2.1.3.8.1 | RowethEtsIndexLookupEntry | not-accessible | current | One conceptual row representing one lookup entry. |
| 1.3.6.1.4.1.2928.2.2.1.3.8.1.1 | ColumnethEtsIndexLookupDevIndex | read-only | current | The value refers to the ethDevIndex in the ethEtsTable for the ETS interface represented by the DSTI. |
| 1.3.6.1.4.1.2928.2.2.1.3.8.1.2 | ColumnethEtsIndexLookupIfIndex | read-only | current | The value refers to the ethIfIndex in the ethEtsTable for the ETS interface represented by the DSTI. |
| 1.3.6.1.4.1.2928.2.2.1.3.9 | TableethIfRstpTable | not-accessible | current | The table contains Rapid Spanning Tree Protocol (RSTP) specific configurations and data for ports. If a port does not support RSTP, then the table will not hol… |
| 1.3.6.1.4.1.2928.2.2.1.3.9.1 | RowethIfRstpEntry | not-accessible | current | An entry represents Rapid Spanning Tree Protocol (RSTP) data for one port (interface). |
| 1.3.6.1.4.1.2928.2.2.1.3.9.1.1 | ColumnethIfRstpPortIdentifier | read-only | current | The unique port identifier. |
| 1.3.6.1.4.1.2928.2.2.1.3.9.1.2 | ColumnethIfRstpPriority | read-write | current | The port priority. The value must be set in increments of 16. |
| 1.3.6.1.4.1.2928.2.2.1.3.9.1.3 | ColumnethIfRstpState | read-only | current | Describes if the port forwards MAC frames and whether or not it learns from their source addresses. discarding(1). The port is not enabled or has been excluded… |
| 1.3.6.1.4.1.2928.2.2.1.3.9.1.4 | ColumnethIfRstpTopologyChangeAcknowledge | read-only | current | true(1). A topology change is in progress and the port is about to acknowledge this. false(2). A topology change is not in progress. |
| 1.3.6.1.4.1.2928.2.2.1.3.9.1.5 | ColumnethIfRstpPathCost | read-write | current | The contribution of this port to the path cost of paths towards the spanning tree root which include this port. A value of zero (0) means that the path cost is… |
| 1.3.6.1.4.1.2928.2.2.1.3.9.1.6 | ColumnethIfRstpDesignatedRoot | read-only | current | The unique bridge identifier of the root bridge. |
| 1.3.6.1.4.1.2928.2.2.1.3.9.1.7 | ColumnethIfRstpDesignatedCost | read-only | current | The path cost to the root bridge from the designated bridge. |
| 1.3.6.1.4.1.2928.2.2.1.3.9.1.8 | ColumnethIfRstpDesignatedBridge | read-only | current | The bridge identifier of the best bridge connected to this port's segment. |
| 1.3.6.1.4.1.2928.2.2.1.3.9.1.9 | ColumnethIfRstpDesignatedPort | read-only | current | The port identifier of the best port on the Designated Bridge. |
| 1.3.6.1.4.1.2928.2.2.1.3.9.1.10 | ColumnethIfRstpAdminEdgePort | read-write | current | Setting of the edge port state of this port. auto(0). The setting of the port as edge port or not is done automatically. See ethIfRstpOperEdgePort for the curr… |
| 1.3.6.1.4.1.2928.2.2.1.3.9.1.11 | ColumnethIfRstpOperEdgePort | read-only | current | The actual state of the port. See ethIfRstpAdminEdgePort for setting of the port state. true(1). The port is an edge port. false(2). The port is not an edge po… |
| 1.3.6.1.4.1.2928.2.2.1.3.9.1.12 | ColumnethIfRstpAdminPointToPointMAC | read-write | current | Setting of the point-to-point state of this port. auto(0). The state becomes `true(1)' if the port is a full-duplex physical port, or an ETS TTP with a maximum… |
| 1.3.6.1.4.1.2928.2.2.1.3.9.1.13 | ColumnethIfRstpOperPointToPointMAC | read-only | current | The point-to-point state of this port. |
| 1.3.6.1.4.1.2928.2.2.1.3.9.1.14 | ColumnethIfRstpCurrentPathCost | read-only | current | The contribution of this port to the path cost of paths towards the spanning tree root which include this port. Unless ethIfRstpPathCost is `auto(1), then this… |
| 1.3.6.1.4.1.2928.2.2.1.3.10 | TableethIfgTable | not-accessible | current | Table that contains definitions of interface groups. For every row in the table, a corresponding row exists in the table ethIfTable. |
| 1.3.6.1.4.1.2928.2.2.1.3.10.1 | RowethIfgEntry | not-accessible | current | An entry representing one interface group. An interface group is a virtual interface that groups two ETS interfaces for 1+1 protected transport of Ethernet. |
| 1.3.6.1.4.1.2928.2.2.1.3.10.1.1 | ColumnethIfgRowStatus | read-create | current | See SNMPv2-TC. The following values are supported: active(1). The object always reads active. createAndGo(4). A new conceptual row is created representing a ne… |
| 1.3.6.1.4.1.2928.2.2.1.3.10.1.2 | ColumnethIfgMembers | read-only | current | A list of the interfaces that are members of the interface group. An interface is added or removed from an interface group from the interface using ethIfInterf… |
| 1.3.6.1.4.1.2928.2.2.1.3.10.1.3 | ColumnethIfgDifferentialDelay | read-only | current | The measured difference delay in microseconds between the two channels in the interface group. |
| 1.3.6.1.4.1.2928.2.2.1.3.10.1.4 | ColumnethIfgDifferentialDelayValid | read-only | current | Specifies if the value of ethIfgDifferentialDelay is valid or not. |
| 1.3.6.1.4.1.2928.2.2.1.3.10.1.5 | ColumnethIfgAheadInterface | read-only | current | The value of ethIfIndex of the interface that is ahead of the other. A value of zero (0) implies invalid, i.e. no channel is established. If only one interface… |
| 1.3.6.1.4.1.2928.2.2.1.3.10.1.6 | ColumnethIfgHitlessProtection | read-create | current | Specifies if hitless protection shall be attempted or not. true(1). Will attempt to reach a hitless protection state. false(2). Will only attempt to reach a st… |
| 1.3.6.1.4.1.2928.2.2.1.3.10.1.7 | ColumnethIfgProtectionStatus | read-only | current | The current protection state. |
| 1.3.6.1.4.1.2928.2.2.1.3.10.1.8 | ColumnethIfgExpectedProtectionStatus | read-create | current | The expected protection state. When the current protection state (see ethIfgProtectionStatus) is lower than the expected protection state, an alarm is raised. … |
| 1.3.6.1.4.1.2928.2.2.1.3.10.1.9 | ColumnethIfgForceHit | read-create | current | A write of zero (0) resets the buffers, and will therefore minimize the the latency penalty incurred by the 1+1 buffering. |
| 1.3.6.1.4.1.2928.2.2.1.3.10.1.10 | ColumnethIfgActiveInterface | read-create | current | The value of ethIfIndex of the interface from where frames are currently being forwarded. If the ethIfgProtectionStatus is `unavailable(1)' then the value is z… |
| 1.3.6.1.4.1.2928.2.2.1.3.10.1.11 | ColumnethIfgExpectChannel | read-create | current | Controls whether a channel is expected to be terminated on this ETS TTPs for the member interfaces or not. This value can only be set if the mode (ethEtsMode) … |
| 1.3.6.1.4.1.2928.2.2.1.3.11 | TableethIfQDropThresholdTable | not-accessible | current | A queue (Traffic Class) can have multiple drop thresholds, one for each drop precedence. The table contains configuration of how to drop frames per combination… |
| 1.3.6.1.4.1.2928.2.2.1.3.11.1 | RowethIfQDropThresholdEntry | not-accessible | current | An entry in the table. |
| 1.3.6.1.4.1.2928.2.2.1.3.11.1.1 | ColumnethIfQDropThresDropPrecedence | read-only | current | The value of drop precedence (DP). The value range is given by the device and is from zero to and including (ethDeviceDropPrecedenceLevels - 1). |
| 1.3.6.1.4.1.2928.2.2.1.3.11.1.2 | ColumnethIfQDropThresMaxFrames | read-write | current | The maximum number of frames that can be queued to this interface for this combination of traffic class and drop precedence. Arriving frames are discarded when… |
| 1.3.6.1.4.1.2928.2.2.1.3.11.1.3 | ColumnethIfQDropThresCurrentMaxFrames | read-only | current | The maximum number of frames that currently can be queued to this interface for this combination of traffic class and drop precedence. This value contains the … |
| 1.3.6.1.4.1.2928.2.2.1.3.11.1.4 | ColumnethIfQDropThresDropProbabilityFunction | read-write | current | The drop probability function that shall be used for the combination of traffic class and drop precedence on the interface. The values supported by the device … |
| 1.3.6.1.4.1.2928.2.2.1.4 | NodeethStatisticsGroup | |||
| 1.3.6.1.4.1.2928.2.2.1.4.1 | TableethStatDcap1Table | not-accessible | current | Table holds statistical DCAP-1 data for interface groups that are implemented using ETS connections. |
| 1.3.6.1.4.1.2928.2.2.1.4.1.1 | RowethStatDcap1Entry | not-accessible | current | A conceptual row holding DCAP-1 statistical data for a single interface group. |
| 1.3.6.1.4.1.2928.2.2.1.4.1.1.1 | ColumnethStatDcap1Reset | read-write | current | Writing a zero (0) to this object resets all counters for the interface. |
| 1.3.6.1.4.1.2928.2.2.1.4.1.1.2 | ColumnethStatDcap1TxOctets | read-only | current | Total number of transmitted octets (bytes). |
| 1.3.6.1.4.1.2928.2.2.1.4.1.1.3 | ColumnethStatDcap1TxPackets | read-only | current | Total number of transmitted packets. |
| 1.3.6.1.4.1.2928.2.2.1.4.1.1.4 | ColumnethStatDcap1TxDiscardOctets | read-only | current | Total number of transmitted and discarded octets (bytes). |
| 1.3.6.1.4.1.2928.2.2.1.4.1.1.5 | ColumnethStatDcap1TxDiscardPackets | read-only | current | Total number of transmitted and discarded packets. |
| 1.3.6.1.4.1.2928.2.2.1.4.1.1.6 | ColumnethStatDcap1TxBitrate | read-only | current | The transmit utilization in bits per second on the connection as a mean value during the last 30 seconds. |
| 1.3.6.1.4.1.2928.2.2.1.4.1.1.7 | ColumnethStatDcap1TxLoad | read-only | current | The transmit utilization (load) in percent on the connection as mean value measured during the last 30 seconds. |
| 1.3.6.1.4.1.2928.2.2.1.4.1.1.8 | ColumnethStatDcap1RxOctets | read-only | current | Total number of received octets (bytes). |
| 1.3.6.1.4.1.2928.2.2.1.4.1.1.9 | ColumnethStatDcap1RxPackets | read-only | current | Total number of received packets. |
| 1.3.6.1.4.1.2928.2.2.1.4.1.1.10 | ColumnethStatDcap1RxDiscardOctets | read-only | current | Total number of received and discarded octets (bytes). |
| 1.3.6.1.4.1.2928.2.2.1.4.1.1.11 | ColumnethStatDcap1RxDiscardPackets | read-only | current | Total number of received packets that are discarded and not counted in ethStatDcap1RxErrorCRC. |
| 1.3.6.1.4.1.2928.2.2.1.4.1.1.12 | ColumnethStatDcap1RxErrorCRC | read-only | current | Total number of received packets with CRC32 error. For an interface group where the protectionStatus is `hitlessProtected(5)', this value is not increased. |
| 1.3.6.1.4.1.2928.2.2.1.4.1.1.13 | ColumnethStatDcap1RxBitrate | read-only | current | The receive utilization in bits per second on the connection as a mean value during the last 30 seconds. |
| 1.3.6.1.4.1.2928.2.2.1.4.1.1.14 | ColumnethStatDcap1RxLoad | read-only | current | The receive utilization (load) in percent on the connection as mean value measured during the last 30 seconds. |
| 1.3.6.1.4.1.2928.2.2.1.4.2 | TableethIfStatTable | not-accessible | current | Table holds statistical data for Ethernet interfaces. |
| 1.3.6.1.4.1.2928.2.2.1.4.2.1 | RowethIfStatEntry | not-accessible | current | A conceptual row holding statistica data for a single interface. |
| 1.3.6.1.4.1.2928.2.2.1.4.2.1.1 | ColumnethIfStatReset | read-write | current | Writing a zero (0) to this object resets all counters for the interface. |
| 1.3.6.1.4.1.2928.2.2.1.4.2.1.2 | ColumnethIfStatTxBitrate | read-only | current | The transmit utilization in bits per second on the interface as a mean value during the last 30 seconds. |
| 1.3.6.1.4.1.2928.2.2.1.4.2.1.3 | ColumnethIfStatTxLoad | read-only | current | The transmit utilization (load) in percent of the wire speed on the interface as mean value measured during the last 30 seconds. |
| 1.3.6.1.4.1.2928.2.2.1.4.2.1.4 | ColumnethIfStatRxBitrate | read-only | current | The receive utilization in bits per second on the interface as a mean value during the last 30 seconds. |
| 1.3.6.1.4.1.2928.2.2.1.4.2.1.5 | ColumnethIfStatRxLoad | read-only | current | The receive utilization (load) in percent of the wire speed on the interface as mean value measured during the last 30 seconds. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| AdvertisedDuplex | BITS { auto(0), fullDuplex(1), halfDuplex(2) } | current | auto(0). If auto-negotiation is enabled (see ethDot3AutoNegotiation), then advertise all duplex that the device supports. If auto-negotiation is disabled, then use full duplex. fullDuplex(1). Advertise that the interfac… |
| AdvertisedFlowControl | BITS { auto(0), pause(1), asmDir(2) } | current | auto(0). Advertise all settings that the port supports. This bit cannot be set at the same time as when any of the other bits are set. Setting this bit will clear the other bits. If auto-negotiation is disabled (see eth… |
| AdvertisedSpeed | BITS { auto(0), b10(1), b100(2), b1000(3), b10g(4) } | current | auto(0). If auto-negotiation is enabled (see ethDot3AutoNegotiate), then advertise all speeds that the device supports. If auto auto-negotiation is disabled, then use the highest speed that the device supports. b10(1). … |
| BridgeIdentifier | OCTET STRING(SIZE (8)) | current | The Bridge-Identifier, as used in the Rapid Spanning Tree Protocol (RSTP), to uniquely identify a bridge. Its first two octets (in network byte order) contain a priority value, and its last 6 octets contain the MAC addr… |
| EthInterfaceType | INTEGER { auto(0), unknown(1), bETS(2), b100baseTX(3), b1000baseSX(4), b1000baseLX(5), b1000baseT(6), bETSGroup(7), b10GbaseSR(8), b10GbaseLR(9), b10GbaseLRM(10), b10GbaseER(11), b10GbaseZR(12) } | current | The type of interface. The value `unknown(1)' is presented if required hardware is missing, or if it otherwise is not possible to determined the type of interface. |
| FrameProcess | INTEGER { notSupported(0), drop(1), forward(2) } | current | Describes how a frame shall be processed: notSupported(0). setting of this value is not supported by the device. drop(1). Frames are dropped. forward(2). Frames are forwarded. |
| IfgProtectionStatus | INTEGER { unavailable(1), unprotected(2), standbyProtected(3), hitlessCapable(4), hitlessProtected(5) } | current | Describes the protection status of a protected service in an interface group. unavailable(1). means that neither channel is up. unprotected(2). means that one of the channels is up. standbyProtected(3). means that both … |
| InterfaceIndexList | OCTET STRING | current | A list of interfaces as ethIfIndex. Each group of 4 octets represents the value of an ethIfIndex. |
| PortIdentifier | OCTET STRING(SIZE (2)) | current | The Port-Identifier, as used in the Rapid Spanning Tree Protocol (RSTP), to uniquely identify the port within the bridge. Its first octet (in network byte order) contains a priority value, and the second octet contains … |
| Timeout | Integer32 | current | A Rapid Spanning Tree Protocol (RSTP) timer in units of 1/100 seconds. Several objects in this MIB module represent values of timers used by the Rapid Spanning Tree Protocol. In this MIB, these timers have values in uni… |
| TrafficClass | Integer32 (0..7) | current | A traffic class. |
| VLANSet | OCTET STRING (SIZE(512)) | current | A set of VLAN ids. The octet string represents a bit array where each bit represents a VLAN id. If the bit is set, then the VLAN id is included in the set. VLANs are identified from left to right, where the leftmost bit… |