RAD-EthIf-MIB
333 objects
Ethernet Interface MIB.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.164.3.1.6.1 | IdentityethIf | Ethernet Interface MIB. | ||
| 1.3.6.1.4.1.164.3.1.6.1.0 | NodeethIfEvents | |||
| 1.3.6.1.4.1.164.3.1.6.1.0.1 | NotificationethLos | current | This trap indicates that a Loss of signal was detected on an ethernet interface. | |
| 1.3.6.1.4.1.164.3.1.6.1.0.4 | NotificationerpStateProtected | current | This trap indicates that ERP ring state changed to protected. | |
| 1.3.6.1.4.1.164.3.1.6.1.0.5 | NotificationerpPortStateChange | current | This trap indicates that the Port State was changed. | |
| 1.3.6.1.4.1.164.3.1.6.1.0.17 | NotificationoamEfmRemoteLoopback | current | This trap indicates that Loopback started. | |
| 1.3.6.1.4.1.164.3.1.6.1.0.19 | NotificationoamEfmRemoteLoopbackOff | current | This trap indicates that Loopback ended. | |
| 1.3.6.1.4.1.164.3.1.6.1.0.20 | NotificationoamEfmLinkFaultIndication | current | This trap indicates Link fault indication. | |
| 1.3.6.1.4.1.164.3.1.6.1.0.21 | NotificationoamEfmFeLinkFaultIndication | current | This trap indicates Link fault indication at Far End. | |
| 1.3.6.1.4.1.164.3.1.6.1.0.22 | NotificationoamEfmCriticalLinkIndication | current | This trap indicates Critical link indication. | |
| 1.3.6.1.4.1.164.3.1.6.1.0.23 | NotificationoamEfmFeCriticalLinkIndication | current | This trap indicates Critical link indication at Far End. | |
| 1.3.6.1.4.1.164.3.1.6.1.0.24 | NotificationoamEfmDyingGaspIndication | current | This trap indicates Dying gasp indication. | |
| 1.3.6.1.4.1.164.3.1.6.1.0.25 | NotificationoamEfmFeDyingGaspIndication | current | This trap indicates Dying gasp indication at Far End. | |
| 1.3.6.1.4.1.164.3.1.6.1.0.26 | NotificationpcsLinkDown | current | This trap indicates that the PCS Link is down. | |
| 1.3.6.1.4.1.164.3.1.6.1.1 | TableethIfTable | not-accessible | current | A table. |
| 1.3.6.1.4.1.164.3.1.6.1.1.1 | RowethIfEntry | not-accessible | current | An entry in table. |
| 1.3.6.1.4.1.164.3.1.6.1.1.1.1 | ColumnethIfIdx | read-only | current | A unique index of the ethernet interface/port. |
| 1.3.6.1.4.1.164.3.1.6.1.1.1.2 | ColumnethMode | read-write | current | This object indicates the Ethernet mode of operation. |
| 1.3.6.1.4.1.164.3.1.6.1.1.1.3 | ColumnethBridgingMode | read-write | current | This object indicates the bridging mode of the Ethernet interface. |
| 1.3.6.1.4.1.164.3.1.6.1.1.1.4 | ColumnethEncapsulationCRCMode | read-write | current | This object define the encapsulation type requested for the Ethernet interface. It indicates if we transfer the Ethernet frame to the other side with or withou… |
| 1.3.6.1.4.1.164.3.1.6.1.1.1.5 | ColumnethBackPressure | read-write | current | This parameter defines whether to enable or disable Back pressure. Back Pressure is a flow control parameter. |
| 1.3.6.1.4.1.164.3.1.6.1.1.1.6 | ColumnethLimit4 | read-write | current | This parameter determine the Back off algorithm mode. Every 4 following collisions the Framer will be thrown out (4 times more than usuall). |
| 1.3.6.1.4.1.164.3.1.6.1.1.1.7 | ColumnethSkipInitReset | read-write | current | This parameter defines whether read status on reset. |
| 1.3.6.1.4.1.164.3.1.6.1.1.1.8 | ColumnethMulticastBlock | read-write | current | This parameter defines whether to send multicast message to WAN from LAN or not. |
| 1.3.6.1.4.1.164.3.1.6.1.1.1.9 | ColumnethBroadcastBlock | read-write | current | This parameter defines whether to send broadcast message to WAN from LAN or not. |
| 1.3.6.1.4.1.164.3.1.6.1.1.1.10 | ColumnethSpeed | read-write | current | This parameter defines the line speed. |
| 1.3.6.1.4.1.164.3.1.6.1.1.1.11 | ColumnethRip2 | read-write | current | This parameter defines whether to send RIP II message to WAN from LAN or not |
| 1.3.6.1.4.1.164.3.1.6.1.1.1.12 | ColumnethPortPriority | read-write | current | This parameter defines if priority is to be considered for this Port. |
| 1.3.6.1.4.1.164.3.1.6.1.1.1.13 | ColumnethPortMngEnable | read-write | current | This parameter defines whether management data can pass through this Port. localOnly (4) - Only local device can be managed via this port. |
| 1.3.6.1.4.1.164.3.1.6.1.1.1.14 | ColumnethFlowCtrlMacAddress | read-write | current | In case of flow control - transmit frame with this specific MAC address to inform the other end to stop sending frames. Default: 01.80.C2.00.00.01. |
| 1.3.6.1.4.1.164.3.1.6.1.1.1.15 | ColumnethRateLimit | read-write | current | This parameter defines the Rate Limit of the line, in Mbps. |
| 1.3.6.1.4.1.164.3.1.6.1.1.1.16 | ColumnethJumboFrameEnable | read-write | current | This parameter defines whether to support Jumbo Frame or not. |
| 1.3.6.1.4.1.164.3.1.6.1.1.1.17 | ColumnethAutoMdiXEnable | read-write | current | This parameter defines whether to support automatic change between MDI and MDI[X]. |
| 1.3.6.1.4.1.164.3.1.6.1.1.1.18 | ColumnethPortDataEnable | read-write | current | This parameter defines whether this port is enabled for data (that is not management). no(2) - management can run on this port yes(3) - both management and pay… |
| 1.3.6.1.4.1.164.3.1.6.1.1.1.19 | ColumnethIfUse | read-write | current | This parameter defines the use of the port. 1=NET 2=USER . |
| 1.3.6.1.4.1.164.3.1.6.1.1.1.20 | ColumnethLineOam | read-write | current | This parameter defines the working mode of 802.AH OAM mechanism. |
| 1.3.6.1.4.1.164.3.1.6.1.1.1.21 | ColumnethRoutingProtocol | read-write | current | This parameter defines the routing protocol used above ETH port. |
| 1.3.6.1.4.1.164.3.1.6.1.1.1.22 | ColumnethMdiXManualSwitch | read-write | current | This parameter sets the port to be MDI-X (cross-over) or MDI (straight-through). It is applicable only when ethAutoMdiXEnable = no, namely, only when the autom… |
| 1.3.6.1.4.1.164.3.1.6.1.1.1.23 | ColumnethDot1xEnable | read-write | current | Determines if the Port-Based Network Access Protocol (IEEE-802.1x) is enabled for the Ethernet Port. |
| 1.3.6.1.4.1.164.3.1.6.1.1.1.24 | ColumnethPartnerRateMode | read-write | current | For converters having couples of ports, where each couple contains a port with an SFP connector and a port with a RJ connector, this parameter is relevant for … |
| 1.3.6.1.4.1.164.3.1.6.1.1.1.25 | ColumnethDot1xPortRole | read-write | current | Determine the functionality of the port in the Port-Based Network Access Protocol (IEEE-802.1x) - either Authenticator or Supplicant. |
| 1.3.6.1.4.1.164.3.1.6.1.1.1.26 | ColumnethDhcpRequest | read-write | current | Determine the interface request for DHCP address after it goes up. never - DHCP requests will never be sent to the interface. normal - DHCP requests will be se… |
| 1.3.6.1.4.1.164.3.1.6.1.1.1.27 | ColumnethSfpCapabilities | read-only | current | For each bit: '1' means that this attribute is supported. Bits 0-5 are relevant when Auto Negotiation = Disabled. 'Full' means Full Duplex; 'Half' means Half D… |
| 1.3.6.1.4.1.164.3.1.6.1.2 | NodeethIfPerformance | |||
| 1.3.6.1.4.1.164.3.1.6.1.2.1 | TableethIfCurrentTable | not-accessible | current | The Ethernet Current table. When the index specifies the Ethernet interface (only), the counters are for an interval of 15 minutes. |
| 1.3.6.1.4.1.164.3.1.6.1.2.1.1 | RowethIfCurrentEntry | not-accessible | current | An entry in the Ethernet Current table. |
| 1.3.6.1.4.1.164.3.1.6.1.2.1.1.1 | ColumnethIfCurrentIndex | read-only | current | The index of the Ethernet interface. It may be ifIndex. For some devices (e.g RICi-622GE), supporting several types of intervals, this index will be a concaten… |
| 1.3.6.1.4.1.164.3.1.6.1.2.1.1.2 | ColumnethIfCurrentStatus | read-only | current | The status of the current interval: 0 - Valid. 1 - redundantLinkSwitch - the link has been switched by a redundancy mechanism. 2 - discontinuity - module was p… |
| 1.3.6.1.4.1.164.3.1.6.1.2.1.1.3 | ColumnethIfCurrentInFrames | read-only | current | The counter associated with the number of received frames, encountered by the Ethernet interface in the current interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.1.1.4 | ColumnethIfCurrentInOctets | read-only | current | The counter associated with the number of received octets, encountered by the Ethernet interface in the current interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.1.1.5 | ColumnethIfCurrentAlignmentErrors | read-only | current | The counter associated with the number of received frames, which are not complete (The result of dividing the number of bits by 8 is not an Integer), encounter… |
| 1.3.6.1.4.1.164.3.1.6.1.2.1.1.6 | ColumnethIfCurrentFCSErrors | read-only | current | The counter associated with the number of received frames that didn't pass the FCS test, encountered by the Ethernet interface in the current interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.1.1.7 | ColumnethIfCurrentLengthError | read-only | current | The counter associated with the number of received frames with length error, encountered by the Ethernet interface in the current interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.1.1.8 | ColumnethIfCurrentOutFrames | read-only | current | The counter associated with the number of transmitted frames, encountered by the Ethernet interface in the current interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.1.1.9 | ColumnethIfCurrentOutOctets | read-only | current | The counter associated with the number of transmitted octets, encountered by the Ethernet interface in the current interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.1.1.10 | ColumnethIfCurrentSingleCollisionFrames | read-only | current | The counter associated with the number of successfully transmitted frames for which transmission was inhibited by exactly one collision, encountered by the Eth… |
| 1.3.6.1.4.1.164.3.1.6.1.2.1.1.11 | ColumnethIfCurrentMultipleCollisionFrames | read-only | current | The counter associated with the number of successfully transmitted frames for which transmission was inhibited by more than one collision, encountered by the E… |
| 1.3.6.1.4.1.164.3.1.6.1.2.1.1.12 | ColumnethIfCurrentDeferredTransmissions | read-only | current | The counter associated with the number of transmitted frames for which the first transmission attempt was delayed due to a busy media, encountered by the Ether… |
| 1.3.6.1.4.1.164.3.1.6.1.2.1.1.13 | ColumnethIfCurrentLateCollisions | read-only | current | The counter associated with the number of times that a collision was detected later than the first 64 bytes of the frame, encountered by the Ethernet interface… |
| 1.3.6.1.4.1.164.3.1.6.1.2.1.1.14 | ColumnethIfCurrentCarrierSenseErrors | read-only | current | The counter associated with the number of times that the carrier sense condition was lost or never asserted when attempting to transmit a frame, encountered by… |
| 1.3.6.1.4.1.164.3.1.6.1.2.1.1.15 | ColumnethIfCurrentInputCongestionDropped | read-only | current | The counter associated with the number of frames dropped due to lack of buffers in ingress pool, encountered by the Ethernet interface in the current interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.1.1.16 | ColumnethIfCurrentOutputCongestionDropped | read-only | current | The counter associated with the number of dropped frames due to a congestion, encountered by the Transmit direction to the Ethernet interface in the current in… |
| 1.3.6.1.4.1.164.3.1.6.1.2.1.1.17 | ColumnethIfCurrentOverflowInFrames | read-only | current | The number of times the associated ethIfCurrentInFrames counter has overflowed in the current interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.1.1.18 | ColumnethIfCurrentOverflowInOctets | read-only | current | The number of times the associated ethIfCurrentInOctets counter has overflowed in the current interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.1.1.19 | ColumnethIfCurrentOverflowFCSErrors | read-only | current | The number of times the associated ethIfCurrentFCSErrors counter has overflowed in the current interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.1.1.20 | ColumnethIfCurrentOverflowOutFrames | read-only | current | The number of times the associated ethIfCurrentOutFrames counter has overflowed in the current interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.1.1.21 | ColumnethIfCurrentOverflowOutOctets | read-only | current | The number of times the associated ethIfCurrentOutOctets counter has overflowed in the current interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.1.1.22 | ColumnethIfCurrentOverflowMultipleCollisionFrames | read-only | current | The number of times the associated ethIfCurrentMultipleCollisionFrames counter has overflowed in the current interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.1.1.23 | ColumnethIfCurrentInUnicastFrames | read-only | current | The number of received Unicast frames, encountered by the Ethernet interface in the current interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.1.1.24 | ColumnethIfCurrentOutUnicastFrames | read-only | current | The number of transmitted Unicast frames, encountered by the Ethernet interface in the current interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.1.1.25 | ColumnethIfCurrentInMulticastFrames | read-only | current | The number of received Multicast frames, encountered by the Ethernet interface in the current interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.1.1.26 | ColumnethIfCurrentOutMulticastFrames | read-only | current | The number of transmitted Multicast frames, encountered by the Ethernet interface in the current interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.1.1.27 | ColumnethIfCurrentInBroadcastFrames | read-only | current | The number of received Broadcast frames, encountered by the Ethernet interface in the current interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.1.1.28 | ColumnethIfCurrentOutBroadcastFrames | read-only | current | The number of transmitted Broadcast frames, encountered by the Ethernet interface in the current interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.1.1.29 | ColumnethIfCurrentInDiscardFrames | read-only | current | The number of received Discarded frames, encountered by the Ethernet interface in the current interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.1.1.30 | ColumnethIfCurrentOutDiscardFrames | read-only | current | The number of transmitted Discarded frames, encountered by the Ethernet interface in the current interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.1.1.31 | ColumnethIfCurrentInPauseFrames | read-only | current | The number of received Pause frames, encountered by the Ethernet interface in the current interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.1.1.32 | ColumnethIfCurrentOutPauseFrames | read-only | current | The number of transmitted Pause frames, encountered by the Ethernet interface in the current interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.1.1.33 | ColumnethIfCurrentOverflowInUnicastFrames | read-only | current | The number of times the associated ethIfCurrentInUnicastFrames counter has overflowed in the current interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.1.1.34 | ColumnethIfCurrentOverflowOutUnicastFrames | read-only | current | The number of times the associated ethIfCurrentOutUnicastFrames counter has overflowed in the current interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.1.1.35 | ColumnethIfCurrentOverflowInMulticastFrames | read-only | current | The number of times the associated ethIfCurrentInMulticastFrames counter has overflowed in the current interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.1.1.36 | ColumnethIfCurrentOverflowOutMulticastFrames | read-only | current | The number of times the associated ethIfCurrentOutMulticastFrames counter has overflowed in the current interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.1.1.37 | ColumnethIfCurrentOverflowInBroadcastFrames | read-only | current | The number of times the associated ethIfCurrentInBroadcastFrames counter has overflowed in the current interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.1.1.38 | ColumnethIfCurrentOverflowOutBroadcastFrames | read-only | current | The number of times the associated ethIfCurrentOutBroadcastFrames counter has overflowed in the current interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.1.1.39 | ColumnethIfCurrentOverflowInDiscardFrames | read-only | current | The number of times the associated ethIfCurrentInDiscardFrames counter has overflowed in the current interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.1.1.40 | ColumnethIfCurrentOverflowOutDiscardFrames | read-only | current | The number of times the associated ethIfCurrentOutDiscardFrames counter has overflowed in the current interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.1.1.41 | ColumnethIfCurrentOverflowInPauseFrames | read-only | current | The number of times the associated ethIfCurrentInPauseFrames counter has overflowed in the current interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.1.1.42 | ColumnethIfCurrentOverflowOutPauseFrames | read-only | current | The number of times the associated ethIfCurrentOutPauseFrames counter has overflowed in the current interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.2 | TableethIfIntervalTable | not-accessible | current | The Ethernet Interval table. When ethIfIntervalIndex specifies the Ethernet interface (only), the counters are for an interval of 15 minutes. |
| 1.3.6.1.4.1.164.3.1.6.1.2.2.1 | RowethIfIntervalEntry | not-accessible | current | An entry in the Ethernet Interval table. |
| 1.3.6.1.4.1.164.3.1.6.1.2.2.1.1 | ColumnethIfIntervalIndex | read-only | current | The index of the Ethernet interface. It may be ifIndex. For some devices (e.g RICi-622GE), supporting several types of intervals, this index will be a concaten… |
| 1.3.6.1.4.1.164.3.1.6.1.2.2.1.2 | ColumnethIfIntervalNumber | read-only | current | The Interval Number. This number is between 1 and x, where 1 is the most recently completed interval and x is the least recently completed interval. For 15 min… |
| 1.3.6.1.4.1.164.3.1.6.1.2.2.1.3 | ColumnethIfIntervalStatus | read-only | current | The status of the interval: 0 - Valid. 1 - redundantLinkSwitch - the link has been switched by a redundancy mechanism. 2 - discontinuity - module was partialy … |
| 1.3.6.1.4.1.164.3.1.6.1.2.2.1.4 | ColumnethIfIntervalInFrames | read-only | current | The counter associated with the number of received frames, encountered by the Ethernet interface in the interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.2.1.5 | ColumnethIfIntervalInOctets | read-only | current | The counter associated with the number of received octets, encountered by the Ethernet interface in the interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.2.1.6 | ColumnethIfIntervalAlignmentErrors | read-only | current | The counter associated with the number of received frames, which are not complete (The result of dividing the number of bits by 8 is not an Integer), encounter… |
| 1.3.6.1.4.1.164.3.1.6.1.2.2.1.7 | ColumnethIfIntervalFCSErrors | read-only | current | The counter associated with the number of received frames that didn't pass the FCS test, encountered by the Ethernet interface in the interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.2.1.8 | ColumnethIfIntervalLengthError | read-only | current | The counter associated with the number of received frames with length error, encountered by the Ethernet interface in the interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.2.1.9 | ColumnethIfIntervalOutFrames | read-only | current | The counter associated with the number of transmitted frames, encountered by the Ethernet interface in the interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.2.1.10 | ColumnethIfIntervalOutOctets | read-only | current | The counter associated with the number of transmitted octets, encountered by the Ethernet interface in the interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.2.1.11 | ColumnethIfIntervalSingleCollisionFrames | read-only | current | The counter associated with the number of successfully transmitted frames for which transmission was inhibited by exactly one collision, encountered by the Eth… |
| 1.3.6.1.4.1.164.3.1.6.1.2.2.1.12 | ColumnethIfIntervalMultipleCollisionFrames | read-only | current | The counter associated with the number of successfully transmitted frames for which transmission was inhibited by more than one collision, encountered by the E… |
| 1.3.6.1.4.1.164.3.1.6.1.2.2.1.13 | ColumnethIfIntervalDeferredTransmissions | read-only | current | The counter associated with the number of transmitted frames for which the first transmission attempt was delayed due to a busy media, encountered by the Ether… |
| 1.3.6.1.4.1.164.3.1.6.1.2.2.1.14 | ColumnethIfIntervalLateCollisions | read-only | current | The counter associated with the number of times that a collision was detected later than the first 64 bytes of the frame, encountered by the Ethernet interface… |
| 1.3.6.1.4.1.164.3.1.6.1.2.2.1.15 | ColumnethIfIntervalCarrierSenseErrors | read-only | current | The counter associated with the number of times that the carrier sense condition was lost or never asserted when attempting to transmit a frame, encountered by… |
| 1.3.6.1.4.1.164.3.1.6.1.2.2.1.16 | ColumnethIfIntervalInputCongestionDropped | read-only | current | The counter associated with the number of dropped frames due to a congestion, encountered by the Receive direction to the Ethernet interface in the interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.2.1.17 | ColumnethIfIntervalOutputCongestionDropped | read-only | current | The counter associated with the number of dropped frames due to a congestion, encountered by the Transmit direction to the Ethernet interface in the interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.2.1.18 | ColumnethIfIntervalOverflowInFrames | read-only | current | The number of times the associated ethIfIntervalInFrames counter has overflowed in the interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.2.1.19 | ColumnethIfIntervalOverflowInOctets | read-only | current | The number of times the associated ethIfIntervalInOctets counter has overflowed in the interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.2.1.20 | ColumnethIfIntervalOverflowFCSErrors | read-only | current | The number of times the associated ethIfIntervalFCSErrors counter has overflowed in the interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.2.1.21 | ColumnethIfIntervalOverflowOutFrames | read-only | current | The number of times the associated ethIfIntervalOutFrames counter has overflowed in the interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.2.1.22 | ColumnethIfIntervalOverflowOutOctets | read-only | current | The number of times the associated ethIfIntervalOutOctets counter has overflowed in the interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.2.1.23 | ColumnethIfIntervalOverflowMultipleCollisionFrames | read-only | current | The number of times the associated ethIfIntervalMultipleCollisionFrames counter has overflowed in the interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.2.1.24 | ColumnethIfIntervalInUnicastFrames | read-only | current | The number of received Unicast frames, encountered by the Ethernet interface in the interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.2.1.25 | ColumnethIfIntervalOutUnicastFrames | read-only | current | The number of transmitted Unicast frames, encountered by the Ethernet interface in the interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.2.1.26 | ColumnethIfIntervalInMulticastFrames | read-only | current | The number of received Multicast frames, encountered by the Ethernet interface in the interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.2.1.27 | ColumnethIfIntervalOutMulticastFrames | read-only | current | The number of transmitted Multicast frames, encountered by the Ethernet interface in the interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.2.1.28 | ColumnethIfIntervalInBroadcastFrames | read-only | current | The number of received Broadcast frames, encountered by the Ethernet interface in the interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.2.1.29 | ColumnethIfIntervalOutBroadcastFrames | read-only | current | The number of transmitted Broadcast frames, encountered by the Ethernet interface in the interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.2.1.30 | ColumnethIfIntervalInDiscardFrames | read-only | current | The number of received Discarded frames, encountered by the Ethernet interface in the interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.2.1.31 | ColumnethIfIntervalOutDiscardFrames | read-only | current | The number of transmitted Discarded frames, encountered by the Ethernet interface in the interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.2.1.32 | ColumnethIfIntervalInPauseFrames | read-only | current | The number of received Pause frames, encountered by the Ethernet interface in the interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.2.1.33 | ColumnethIfIntervalOutPauseFrames | read-only | current | The number of transmitted Pause frames, encountered by the Ethernet interface in the interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.2.1.34 | ColumnethIfIntervalOverflowInUnicastFrames | read-only | current | The number of times the associated ethIfIntervalInUnicastFrames counter has overflowed in the interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.2.1.35 | ColumnethIfIntervalOverflowOutUnicastFrames | read-only | current | The number of times the associated ethIfIntervalOutUnicastFrames counter has overflowed in the interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.2.1.36 | ColumnethIfIntervalOverflowInMulticastFrames | read-only | current | The number of times the associated ethIfIntervalInMulticastFrames counter has overflowed in the interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.2.1.37 | ColumnethIfIntervalOverflowOutMulticastFrames | read-only | current | The number of times the associated ethIfIntervalOutMulticastFrames counter has overflowed in the interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.2.1.38 | ColumnethIfIntervalOverflowInBroadcastFrames | read-only | current | The number of times the associated ethIfIntervalInBroadcastFrames counter has overflowed in the interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.2.1.39 | ColumnethIfIntervalOverflowOutBroadcastFrames | read-only | current | The number of times the associated ethIfIntervalOutBroadcastFrames counter has overflowed in the interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.2.1.40 | ColumnethIfIntervalOverflowInDiscardFrames | read-only | current | The number of times the associated ethIfIntervalInDiscardFrames counter has overflowed in the interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.2.1.41 | ColumnethIfIntervalOverflowOutDiscardFrames | read-only | current | The number of times the associated ethIfIntervalOutDiscardFrames counter has overflowed in the interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.2.1.42 | ColumnethIfIntervalOverflowInPauseFrames | read-only | current | The number of times the associated ethIfIntervalInPauseFrames counter has overflowed in the interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.2.1.43 | ColumnethIfIntervalOverflowOutPauseFrames | read-only | current | The number of times the associated ethIfIntervalOutPauseFrames counter has overflowed in the interval. |
| 1.3.6.1.4.1.164.3.1.6.1.2.3 | ScalarethPerformanceMode | read-write | current | This object indicates whether OK or Fail statistics will be counted. |
| 1.3.6.1.4.1.164.3.1.6.1.2.4 | TableethIfPerfTable | not-accessible | current | The Ethernet Performance table. |
| 1.3.6.1.4.1.164.3.1.6.1.2.4.1 | RowethIfPerfEntry | not-accessible | current | An entry in the Ethernet Performance table. |
| 1.3.6.1.4.1.164.3.1.6.1.2.4.1.1 | ColumnethIfPerfInOkFrames | read-only | current | The counter associated with the number of received OK frames, encountered by the Ethernet interface since ethPerformanceMode Set to countOK (2) or Reset Statis… |
| 1.3.6.1.4.1.164.3.1.6.1.2.4.1.2 | ColumnethIfPerfOutOkFrames | read-only | current | The counter associated with the number of transmitted OK frames, encountered by the Ethernet interface since ethPerformanceMode Set to countOK (2) or Reset Sta… |
| 1.3.6.1.4.1.164.3.1.6.1.2.4.1.3 | ColumnethIfPerfTotalCollisions | read-only | current | The counter associated with the total number of collisions of any type encountered by the Ethernet interface since ethPerformanceMode Set to countOK (2) or Res… |
| 1.3.6.1.4.1.164.3.1.6.1.2.4.1.4 | ColumnethIfPerfInOkOctets | read-only | current | The counter associated with the number of received OK Octets, encountered by the Ethernet interface since ethPerformanceMode Set to countOK (2) or Reset Statis… |
| 1.3.6.1.4.1.164.3.1.6.1.2.5 | TableethIfStatsTable | not-accessible | current | The Ethernet running statistics table. The table contains running counters definition. For counter reset use prtParamResetStatsCmd OBJECT. |
| 1.3.6.1.4.1.164.3.1.6.1.2.5.1 | RowethIfStatsEntry | not-accessible | current | An entry in the Ethernet running statistics table. |
| 1.3.6.1.4.1.164.3.1.6.1.2.5.1.1 | ColumnethIfStatsInOctets | read-only | current | The total number of octets received on the interface, including framing characters. Equivalent standard counter: 2863.ifHCInOctets Caption: Total octets receiv… |
| 1.3.6.1.4.1.164.3.1.6.1.2.5.1.2 | ColumnethIfStatsInPkts | read-only | current | The total number of frames (including bad frames, broadcast frames, and multicast frames) received. Equivalent standard counter: 3273.etherStatsHighCapacityPkt… |
| 1.3.6.1.4.1.164.3.1.6.1.2.5.1.3 | ColumnethIfStatsInUcastPkts | read-only | current | The number of received frames, which were not addressed to a multicast or broadcast address. Equivalent standard counter: 2863.ifHCInUcastPkts Caption: Unicast… |
| 1.3.6.1.4.1.164.3.1.6.1.2.5.1.4 | ColumnethIfStatsInMulticastPkts | read-only | current | The number of received frames, which were addressed to a multicast address. Equivalent standard counter: 2863.ifHCInMulticastPkts Caption: Multicast frames rec… |
| 1.3.6.1.4.1.164.3.1.6.1.2.5.1.5 | ColumnethIfStatsInBroadcastPkts | read-only | current | The number of received frames, which were addressed to a broadcast address. Equivalent standard counter: 2863.ifHCInBroadcastPkts Caption: Broadcast frames rec… |
| 1.3.6.1.4.1.164.3.1.6.1.2.5.1.6 | ColumnethIfStatsInJabberPkts | read-only | current | The total number of frames received that were longer than the longest permitted packet (excluding framing bits, but including FCS octets), and had either a bad… |
| 1.3.6.1.4.1.164.3.1.6.1.2.5.1.7 | ColumnethIfStatsInL2CPDiscardPkts | read-only | current | The total number of discarded L2CP frames received. The l2cpStatTable.l2cpStatProtocol object defines list of the Layer 2 protocol that is monitored. Caption: … |
| 1.3.6.1.4.1.164.3.1.6.1.2.5.1.8 | ColumnethIfStatsInCFMDiscardPkts | read-only | current | The number of discarded CFM frames received. Caption: CFM RX frames discarded |
| 1.3.6.1.4.1.164.3.1.6.1.2.5.1.9 | ColumnethIfStatsInACLDiscardPkts | read-only | current | The number of discarded ACL frames received. Caption: ACL RX frames discarded |
| 1.3.6.1.4.1.164.3.1.6.1.2.5.1.10 | ColumnethIfStatsInFCSErrorPkts | read-only | current | The number of frames received that are an integral number of octets in length but do not pass the FCS check. This count does not include frames received with f… |
| 1.3.6.1.4.1.164.3.1.6.1.2.5.1.11 | ColumnethIfStatsInMacOverflowPkts | read-only | current | The number of received packets discarded due to MAC FIFO overflow. Caption: MAC overload RX frames discarded |
| 1.3.6.1.4.1.164.3.1.6.1.2.5.1.12 | ColumnethIfStatsInternalMacReceiveErrors | read-only | current | The number of frames received that failed due to an internal MAC receive error. Equivalent standard counter: 3635.dot3HCStatsInternalMacReceiveErrors Caption: … |
| 1.3.6.1.4.1.164.3.1.6.1.2.5.1.13 | ColumnethIfStatsInUndersizePkts | read-only | current | The number of frames received that were less than 64 octets long (excluding framing bits, but including FCS octets) and were otherwise well formed. Equivalent … |
| 1.3.6.1.4.1.164.3.1.6.1.2.5.1.14 | ColumnethIfStatsInPkts64Octets | read-only | current | The total number of frames (including bad frames) received that were 64 bytes in length (excluding framing bits but including FCS octets). Equivalent standard … |
| 1.3.6.1.4.1.164.3.1.6.1.2.5.1.15 | ColumnethIfStatsInPkts65to127Octets | read-only | current | The total number of frames (including bad frames) received that were between 65 and 127 octets in length (excluding framing bits but including FCS octets). Equ… |
| 1.3.6.1.4.1.164.3.1.6.1.2.5.1.16 | ColumnethIfStatsInPkts128to255Octets | read-only | current | The total number of frames (including bad frames) received that were between 128 and 255 octets in length (excluding framing bits but including FCS octets). Eq… |
| 1.3.6.1.4.1.164.3.1.6.1.2.5.1.17 | ColumnethIfStatsInPkts256to511Octets | read-only | current | The total number of frames (including bad frames) received that were between 256 and 511 octets in length (excluding framing bits but including FCS octets). Eq… |
| 1.3.6.1.4.1.164.3.1.6.1.2.5.1.18 | ColumnethIfStatsInPkts512to1023Octets | read-only | current | The total number of frames (including bad frames) received that were between 511 and 1023 octets in length (excluding framing bits but including FCS octets). E… |
| 1.3.6.1.4.1.164.3.1.6.1.2.5.1.19 | ColumnethIfStatsInPkts1024to1518Octets | read-only | current | The total number of frames (including bad frames) received that were between 1024 and 1518 octets in length (excluding framing bits but including FCS octets). … |
| 1.3.6.1.4.1.164.3.1.6.1.2.5.1.20 | ColumnethIfStatsInPkts1519to2047Octets | read-only | current | The total number of frames (including bad frames) received that were between 1519 and 2047 octets in length (excluding framing bits but including FCS octets). … |
| 1.3.6.1.4.1.164.3.1.6.1.2.5.1.21 | ColumnethIfStatsInPkts1519toMaxOctets | read-only | current | The total number of frames (including bad frames) received that were between 1519 and maximum permitted size in length (excluding framing bits but including FC… |
| 1.3.6.1.4.1.164.3.1.6.1.2.5.1.22 | ColumnethIfStatsInPkts2048toMaxOctets | read-only | current | The total number of frames (including bad frames) received that were between 2048 and maximum permitted size in length (excluding framing bits but including FC… |
| 1.3.6.1.4.1.164.3.1.6.1.2.5.1.23 | ColumnethIfStatsInOversizePkts | read-only | current | The number of frames received that exceed the maximum permitted size. Equivalent standard counter: 3635.dot3HCStatsFrameTooLongs Caption: Oversize frames recei… |
| 1.3.6.1.4.1.164.3.1.6.1.2.5.1.24 | ColumnethIfStatsInErrorPkts | read-only | current | The number of frames received that contained errors preventing them from being deliverable to a higher-layer protocol. Equivalent standard counter: 2863.ifInEr… |
| 1.3.6.1.4.1.164.3.1.6.1.2.5.1.25 | ColumnethIfStatsOutOctets | read-only | current | The total number of octets transmitted out the interface, including framing characters. Equivalent standard counter: 2863.ifHCOutOctets Caption: Total octets t… |
| 1.3.6.1.4.1.164.3.1.6.1.2.5.1.26 | ColumnethIfStatsOutPkts | read-only | current | The total number of frames that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sub-l… |
| 1.3.6.1.4.1.164.3.1.6.1.2.5.1.27 | ColumnethIfStatsOutUcastPkts | read-only | current | The number of transmitted frames, which were not addressed to a multicast or broadcast address. Equivalent standard counter: 2863.ifHCOutUcastPkts Caption: Uni… |
| 1.3.6.1.4.1.164.3.1.6.1.2.5.1.28 | ColumnethIfStatsOutMulticastPkts | read-only | current | The number of transmitted frames, which were addressed to a multicast address. Equivalent standard counter: 2863.ifHCOutMulticastPkts Caption: Multicast frames… |
| 1.3.6.1.4.1.164.3.1.6.1.2.5.1.29 | ColumnethIfStatsOutBroadcastPkts | read-only | current | The number of transmitted frames, which were addressed to a broadcast address. Equivalent standard counter: 2863.ifHCOutBroadcastPkts Caption: Broadcast frames… |
| 1.3.6.1.4.1.164.3.1.6.1.2.5.1.30 | ColumnethIfStatsOutDiscardPkts | read-only | current | The number of correct frames that higher-level protocols requested be transmitted, which were discarded. One possible reason for discarding such a packet could… |
| 1.3.6.1.4.1.164.3.1.6.1.2.5.1.31 | ColumnethIfStatsOutPkts64Octets | read-only | current | The number of transmitted frames that were 64 bytes in length (excluding framing bits but including FCS octets). Caption: 64-octet frames transmitted |
| 1.3.6.1.4.1.164.3.1.6.1.2.5.1.32 | ColumnethIfStatsOutPkts65to127Octets | read-only | current | The number of transmitted frames that were between 65 and 127 octets in length (excluding framing bits but including FCS octets). Caption: 65-to-127-octet fram… |
| 1.3.6.1.4.1.164.3.1.6.1.2.5.1.33 | ColumnethIfStatsOutPkts128to255Octets | read-only | current | The number of transmitted frames that were between 128 and 255 octets in length (excluding framing bits but including FCS octets). Caption: 128-to-255-octet fr… |
| 1.3.6.1.4.1.164.3.1.6.1.2.5.1.34 | ColumnethIfStatsOutPkts256to511Octets | read-only | current | The number of transmitted frames that were between 256 and 511 octets in length (excluding framing bits but including FCS octets). Caption: 256-to-511-octet fr… |
| 1.3.6.1.4.1.164.3.1.6.1.2.5.1.35 | ColumnethIfStatsOutPkts512to1023Octets | read-only | current | The number of transmitted frames that were between 511 and 1023 octets in length (excluding framing bits but including FCS octets). Caption: 511-to-1023-octet … |
| 1.3.6.1.4.1.164.3.1.6.1.2.5.1.36 | ColumnethIfStatsOutPkts1024to1518Octets | read-only | current | The number of transmitted frames that were between 1024 and 1518 octets in length (excluding framing bits but including FCS octets). Caption: 1024-to-1518-octe… |
| 1.3.6.1.4.1.164.3.1.6.1.2.5.1.37 | ColumnethIfStatsOutPkts1519to2047Octets | read-only | current | The number of transmitted frames that were between 1519 and 2047 octets in length (excluding framing bits but including FCS octets). Caption: 1519-to-2047-octe… |
| 1.3.6.1.4.1.164.3.1.6.1.2.5.1.38 | ColumnethIfStatsOutPkts2048toMaxOctets | read-only | current | The number of transmitted frames that were between 2048 and maximum permitted size in length (excluding framing bits but including FCS octets). Caption: 2048-t… |
| 1.3.6.1.4.1.164.3.1.6.1.2.5.1.39 | ColumnethIfStatsOutOversizePkts | read-only | current | The number of frames that higher-level protocols requested to be transmitted, which exceed the maximum permitted size. These frames are discarded. Caption: Ove… |
| 1.3.6.1.4.1.164.3.1.6.1.2.5.1.40 | ColumnethIfStatsInUnMappedCosFrames | read-only | current | The number of frames received that dropped due to mapping to a cos level which is not defined at the flow envelope profile or multicos counter definition. Capt… |
| 1.3.6.1.4.1.164.3.1.6.1.2.5.1.42 | ColumnethIfStatsEgressMTUDiscarded | read-only | current | The number of transmitted frames which were dropped because they were exceeding the egress MTU limit configured over the port |
| 1.3.6.1.4.1.164.3.1.6.1.2.5.1.43 | ColumnethIfStatsLastEgressMTUDiscardingFlow | read-only | current | Pointer to the last flow on which frames were discarded because they were exceeding the egress MTU limit configured over the port. ZeroDotZero is the initial v… |
| 1.3.6.1.4.1.164.3.1.6.1.4 | NodeethIfRing | |||
| 1.3.6.1.4.1.164.3.1.6.1.4.0 | NodeethIfRingEvents | |||
| 1.3.6.1.4.1.164.3.1.6.1.4.0.1 | NotificationethIfRingStatusChange | current | This trap indicates that the status of the Ethernet Ring has been changed. | |
| 1.3.6.1.4.1.164.3.1.6.1.4.1 | TableethIfRingTable | not-accessible | current | Ethernet Ring Table. |
| 1.3.6.1.4.1.164.3.1.6.1.4.1.1 | RowethIfRingEntry | not-accessible | current | An entry in the table. |
| 1.3.6.1.4.1.164.3.1.6.1.4.1.1.1 | ColumnethIfRingIdx | not-accessible | current | This object is an Index that can indicate Slot, Ring, Cnfg etc., according to the device used. When NA, 1 will be used. |
| 1.3.6.1.4.1.164.3.1.6.1.4.1.1.2 | ColumnethIfRingAdminStatus | read-write | current | This object denotes the Ethernet Ring administrative status. |
| 1.3.6.1.4.1.164.3.1.6.1.4.1.1.3 | ColumnethIfRingPorts | read-write | current | The set of ports which are assigned to be ring members. The default value of this object is a string of zeros. |
| 1.3.6.1.4.1.164.3.1.6.1.4.1.1.4 | ColumnethIfRingOperStatus | read-only | current | This object indicates the Ethernet Ring operational status. |
| 1.3.6.1.4.1.164.3.1.6.1.4.1.1.5 | ColumnethIfRingKeepAliveInterval | read-write | current | This parameter indicates the period of time (in msec.) between two consequent Keep Alive messages. |
| 1.3.6.1.4.1.164.3.1.6.1.4.1.1.6 | ColumnethIfRingKeepAliveThresh | read-write | current | This parameter indicates the maximum number of missed Keep Alive answer messages acceptable, after which link status will be failed. |
| 1.3.6.1.4.1.164.3.1.6.1.4.1.1.7 | ColumnethIfRingKeepAliveVlanId | read-write | current | Dedicated VLAN ID for keep alive messages. |
| 1.3.6.1.4.1.164.3.1.6.1.4.1.1.8 | ColumnethIfRingMultiCastVlanId | read-write | current | Dedicated VLAN ID for multicast messages. |
| 1.3.6.1.4.1.164.3.1.6.1.4.1.1.9 | ColumnethIfRingRowStatus | read-write | current | Implement creation/deletion of rings in the device. |
| 1.3.6.1.4.1.164.3.1.6.1.4.2 | Nodeerp | |||
| 1.3.6.1.4.1.164.3.1.6.1.4.2.1 | TableerpTable | not-accessible | current | Ethernet Ring Protection (ERP) G.8032 Table. |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.1.1 | RowerpEntry | not-accessible | current | An entry in the table. |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.1.1.1 | ColumnerpIdx | not-accessible | current | This is the unique Ethernet Protection Ring number. |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.1.1.2 | ColumnerpRowStatus | read-create | current | This object enables creation and deletion of entries in the erpTable. |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.1.1.3 | ColumnerpAdminStatus | read-create | current | This object determines the Ethernet Protection Ring Administrative Status. Value cannot be changed to Up,if erpRowStatus=notReady. Value cannot be changed to U… |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.1.1.4 | ColumnerpNodeState | read-only | current | This object indicates Node state of the Ethernet Protection Ring. init=initial state idle=normal operation protected=protection state. |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.1.1.5 | ColumnerpBridgeNum | read-create | current | Bridge number the ERP ports belong to. Default=1. |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.1.1.6 | ColumnerpEastPort | read-create | current | ifIndex of the Bridge Port, that is the East Port of the ERP. This Bridge Port belongs to erpBridgeNum. Default=0. |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.1.1.7 | ColumnerpWestPort | read-create | current | ifIndex of the Bridge Port, that is the West Port of the ERP. This Bridge Port belongs to erpBridgeNum. Default=0. |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.1.1.8 | ColumnerpRplPort | read-create | current | This object is in use only in ERPv1 (not in use in ERPv2). It indicates the Ring Port, that has the role of RPL. notApplicable(1) if none of the ERP Ports serv… |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.1.1.9 | ColumnerpRapsVlanId | read-create | current | VLAN ID used for Ring APS (RAPS) messages. Valid values are: 1..4094. Value must be different, for different erpIdx. Default=0. |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.1.1.10 | ColumnerpOamCfmMel | read-create | current | ERP MEL (Maintenance Entity Group Level). Valid values are: 0..7. Default=255. |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.1.1.11 | ColumnerpWTR | read-create | current | Wait to Restore (WTR) time in msec. After the failed working transport entity recovers, in order to prevent frequent operations of the protection switch due to… |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.1.1.12 | ColumnerpWTRStatus | read-only | current | Wait to Restore (WTR) status. When equals 0 - WTR is stopped. Otherwise - WTR is running. When WTR is running, there are two cases: - If Agent supports countin… |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.1.1.13 | ColumnerpGuardTimer | read-create | current | Guard Timer in msec. The guard timer is used to prevent ring nodes from receiving outdated R-APS messages. During the duration of the Guard Timer, all received… |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.1.1.14 | ColumnerpHoldoffTimer | read-create | current | Holdoff Timer in msec. When Holdoff Timer>0, the Local SF signal starts the timer and doesn't trigger the Ring Protection immediately. In this case, when Holdo… |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.1.1.15 | ColumnerpForceSfCmd | read-create | current | SF (Signal Fail) command on a port of ERP. eastOn= enforce SF command to East Port of ERP westOn= enforce SF command to West Port of ERP eastClear= Clear exist… |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.1.1.16 | ColumnerpClearStatistics | read-create | current | bit 0 - Clear statistics command for ERP east port(when equals 1). It will cause clearing all Statistics counters of this ERP port. bit 1 - Clear statistics co… |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.1.1.17 | ColumnerpRapsVlanPriority | read-create | current | Priority of the VLAN used for Ring APS (RAPS) messages. Valid values are: 0..7. Default=7. |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.1.1.18 | ColumnerpDescr | read-create | current | Description of the current ERP entry. Default description will be: ' ' |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.1.1.19 | ColumnerpRingType | read-create | current | This object determines the Ring's type: MajorRing or SubRing. Default=majorRing(1) |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.1.1.20 | ColumnerpWTBStatus | read-only | current | Wait To Block (WTR) status. When equals 0 - WTR is stopped. Otherwise - WTR is running. When WTR is running, there are two cases: - If Agent supports counting … |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.1.1.21 | ColumnerpRevertiveMode | read-create | current | In revertive operation, the traffic channel is restored to the working transport entity, i.e., blocked on teh RPL, once the case of clearing the defect, and af… |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.1.1.22 | ColumnerpBackwardCompatibility | read-create | current | When the Ring Node of ERPv2 is part of a Ring, that is composed of other Ring Nodes with ERPv1, it has to run in Compatibility Mode. This mode filters the conf… |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.1.1.23 | ColumnerpTopologyChangepropogation | read-create | current | This object indicates whether to execute Flush Database (FDB) or not in case the RPL owner will unblock the RPL Port. ERPv2 requires FDB in order to relearn th… |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.1.1.24 | ColumnerpInterconnectionNode | read-create | current | The user will be able to configure the Node as an interconnection Node, i.e., a Node that shares more than one Ring. Default value shall be false(2). |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.1.1.25 | ColumnerpCommand | read-create | current | This object represents the external command the user can initiate on the Node: Force Switch(1), Manual Switch(2), clearing any previous command(3), or having n… |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.1.1.26 | ColumnerpCommandParam | read-create | current | This object indicates the port to which the external command (erpCommand) will be issued. Default is notApplicable(1). |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.1.1.27 | ColumnerpEastPhyPort | read-create | current | This object indicates the ifIndex of east Ethernet port. |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.1.1.28 | ColumnerpWestPhyPort | read-create | current | This object indicates the ifIndex of west Ethernet port. |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.1.1.29 | ColumnerpCosMapProfile | read-create | current | This attribute point to the CoS mapping profile Table (cosInternalProfileTable). |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.1.1.30 | ColumnerpVirtualChannel | read-create | current | This object defines whether or not virtual channel is used. It is only relevant for subring nodes, and ignored by major ring nodes. |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.1.1.31 | ColumnerpPassthroughVids | read-create | current | This object contains a 4096 bit vector indicating VIDs passing through the ring, without being terminated like data VLANs are. The high order bit of the first … |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.1.1.32 | ColumnerpColorMapProfile | read-create | current | If this object is zero DEI is used. Otherwise, it is the index of a mapping profile. |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.1.1.33 | ColumnerpPassthroughQueueBlockEast | read-create | current | East queue block for passthrough VLANs. The object points to an existing entry of rad.queueGroupTable. zeroDotZero means the designated default queue block. |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.1.1.34 | ColumnerpPassthroughQueueBlockWest | read-create | current | West queue block for passthrough VLANs. The object points to an existing entry of rad.queueGroupTable. zeroDotZero means the designated default queue block. |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.2 | TableerpPortTable | not-accessible | current | Ethernet Ring Protection (G.8032)Port Table. |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.2.1 | RowerpPortEntry | not-accessible | current | An entry in the table. Rings are created in erpTable. If erpRowStatus=notReady, this table may not include data for this instance of the ERP. |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.2.1.1 | ColumnerpPortIdx | not-accessible | current | This object is the ERP Port, all table objects refer. |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.2.1.2 | ColumnerpPortOamCfmMdId | read-write | current | The index of the Maintenance Domain used by this ERP Port. Default=0=not applicable. |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.2.1.3 | ColumnerpPortOamCfmMaId | read-write | current | The index of the Maintenance Association in the erpPortOamCfmMdId, used by this ERP Port. Default=0=not applicable. |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.2.1.4 | ColumnerpPortOamCfmMepId | read-write | current | The index of the MEP (Maintenance Entity Group End Point)in the relevant erpPortOamCfmMdId and erpPortOamCfmMaId, used by this ERP Port. Default=0=not applicab… |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.2.1.5 | ColumnerpPortState | read-only | current | State of the ERP Port. blocked(2) means only Data Channel is blocked. |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.2.1.6 | ColumnerpPortLocalSfSource | read-only | current | Signal Fail Local Source of the ERP Port: - notApplicable - no Signal Fail (so no source) - serverLayer - Signal Fail is received from the port - oamCfm - Sign… |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.2.1.7 | ColumnerpPortRapsRxValidMsg | read-only | current | Total Received Valid RAPS (RING APS) messages, since [both ports of the Ring are defined (erpEastPort>0, erpWestPort>0; see erpTable), and erpRapsVlanId>0 (see… |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.2.1.8 | ColumnerpPortRapsRxInvalidMsg | read-only | current | Total Received Invalid RAPS (RING APS) messages on this port, since [both ports of the Ring are defined (erpEastPort>0, and erpWestPort>0; see erpTable), erpRa… |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.2.1.9 | ColumnerpPortRapsRxSfMsg | read-only | current | Received SF (Signal Fail) RAPS (RING APS) messages on this port, since [both ports of the Ring are defined (erpEastPort>0, and erpWestPort>0; see erpTable), er… |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.2.1.10 | ColumnerpPortRapsRxNrMsg | read-only | current | Received NR (No Request) RAPS (RING APS) messages on this port, since [both ports of the Ring are defined (erpEastPort>0, and erpWestPort>0; see erpTable), erp… |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.2.1.11 | ColumnerpPortRapsRxNrrbMsg | read-only | current | Received NRRB (No Request and RPL Blocked indication) RAPS (RING APS) messages on this port, since [both ports of the Ring are defined (erpEastPort>0, and erpW… |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.2.1.12 | ColumnerpPortRapsTxValidMsg | read-only | current | Total Transmitted Valid RAPS (RING APS) messages, since [both ports of the Ring are defined (erpEastPort>0, and erpWestPort>0; see erpTable), erpRapsVlanId>0 (… |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.2.1.13 | ColumnerpPortRapsTxInvalidMsg | read-only | current | Total Transmitted Invalid RAPS (RING APS) messages on this port, since [both ports of the Ring are defined (erpEastPort>0, and erpWestPort>0; see erpTable), er… |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.2.1.14 | ColumnerpPortRapsTxSfMsg | read-only | current | Transmitted SF (Signal Fail) RAPS (RING APS) messages on this port, since [both ports of the Ring are defined (erpEastPort>0, and erpWestPort>0; see erpTable),… |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.2.1.15 | ColumnerpPortRapsTxNrMsg | read-only | current | Transmitted NR (No Request) RAPS (RING APS) messages on this port, since [both ports of the Ring are defined (erpEastPort>0, and erpWestPort>0; see erpTable), … |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.2.1.16 | ColumnerpPortRapsTxNrrbMsg | read-only | current | Transmitted NRRB (No Request and RPL Blocked indication) RAPS (RING APS) messages on this port, since [both ports of the Ring are defined (erpEastPort>0, and e… |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.2.1.17 | ColumnerpPortDescr | read-write | current | Description of the current ERP port entry. Default description will be: ' ' |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.2.1.18 | ColumnerpPortRapsRxFsMsg | read-only | current | Received FS (Force Switch) RAPS (RING APS) messages on this port. |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.2.1.19 | ColumnerpPortRapsRxMsMsg | read-only | current | Received MS (Manual Switch) RAPS (RING APS) messages on this port. |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.2.1.20 | ColumnerpPortRapsRxDnfMsg | read-only | current | Received messages with DNF(Do Not Flush) bit=on on this port. |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.2.1.21 | ColumnerpPortRapsRxEvtMsg | read-only | current | Total received RAPS (RING APS) Event-messages on this port. |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.2.1.22 | ColumnerpPortRapsTxFsMsg | read-only | current | Transmitted FS (Force Switch) RAPS (RING APS) messages on this port. |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.2.1.23 | ColumnerpPortRapsTxMsMsg | read-only | current | Transmitted MS (Manual Switch) RAPS (RING APS) messages on this port. |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.2.1.24 | ColumnerpPortRapsTxDnfMsg | read-only | current | Transmitted messages with DNF(Do Not Flush) bit=on on this port. |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.2.1.25 | ColumnerpPortRapsTxEvtMsg | read-only | current | Total transmitted RAPS (RING APS) Event-messages on this port. |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.2.1.26 | ColumnerpPortType | read-write | current | This Object is used only in ERPv2 (not in use in ERPv1). rpl(2) if the port is RPL owner. neighbor(3) if the port is RPL Neighbor. nextNeighbor(4) if the port … |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.4 | TableerpSubRingTable | not-accessible | current | Ethernet Ring Protection (ERP) G.8032 Sub Ring Table. |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.4.1 | RowerpSubRingEntry | not-accessible | current | An entry in the table. |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.4.1.1 | ColumnerpSubRingMajorRingIndex | not-accessible | current | This index represents the Major Ring ID. |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.4.1.2 | ColumnerpSubRingSubRingIndex | not-accessible | current | This index represents the Sub Ring ID. |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.4.1.3 | ColumnerpSubRingRowStatus | read-create | current | This object enables creation and deletion of entries in the erpSubRingTable. |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.4.1.4 | ColumnerpSubRingVirtualChannel | read-create | deprecated | This object is currently deprecated, and replaced by erpVirtualChannel. When setting this value, erpVirtualChannel will be set to the same value. The original … |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.4.1.5 | ColumnerpSubRingRAPSVlanId | read-create | current | VLAN ID for Ring APS messages. Valid values are: 1..4094. Default=0. |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.4.1.6 | ColumnerpSubRingRAPSVlanPriority | read-create | current | Priority of the VLAN used for Ring APS (RAPS) messages for Sub Ring in Major Ring Channels. Valid values are: 0..7. Default=0. |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.5 | TableerpVlanTable | not-accessible | current | Ethernet Ring Protection (ERP) Data Vlan Table. |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.5.1 | RowerpVlanEntry | not-accessible | current | An entry in the table. |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.5.1.1 | ColumnerpVlanIdx | not-accessible | current | This index represents the data Vlan. |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.5.1.2 | ColumnerpVlanRowStatus | read-create | current | This RowStatus is use to create and delete row in the table. |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.5.1.3 | ColumnerpVlanEastQblock | read-create | current | This object indicates the East Qblock. |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.5.1.4 | ColumnerpVlanWestQblock | read-create | current | This object indicates the West Qblock. |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.5.1.5 | ColumnerpVlanServiceIdName | read-create | current | This attribute defines the Service name of this erp Vlan Service, if the VLAN is not associated with a Service the value is null. Upon seting a value, the agen… |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.5.1.6 | ColumnerpVlanMajorEastQblock | read-create | current | This object indicates the Major East Qblock and relevant only if erpInterconnectionNode = true(1). |
| 1.3.6.1.4.1.164.3.1.6.1.4.2.5.1.7 | ColumnerpVlanMajorWestQblock | read-create | current | This object indicates the Major West Qblock and relevant only if erpInterconnectionNode = true(1). |
| 1.3.6.1.4.1.164.3.1.6.1.5 | NodeethIfStorming | |||
| 1.3.6.1.4.1.164.3.1.6.1.5.1 | TableethIfStormTable | not-accessible | current | Ethernet Storming Table. |
| 1.3.6.1.4.1.164.3.1.6.1.5.1.1 | RowethIfStormEntry | not-accessible | current | An entry in the table. |
| 1.3.6.1.4.1.164.3.1.6.1.5.1.1.1 | ColumnethIfStormCnfgIdx | not-accessible | current | This attribute indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg. |
| 1.3.6.1.4.1.164.3.1.6.1.5.1.1.2 | ColumnethIfStormIfIdx | not-accessible | current | A unique index of the ethernet interface/port. |
| 1.3.6.1.4.1.164.3.1.6.1.5.1.1.3 | ColumnethIfStormDirection | not-accessible | current | This object indicates the port's Storm Direction. |
| 1.3.6.1.4.1.164.3.1.6.1.5.1.1.4 | ColumnethIfStormPacketType | not-accessible | current | Packet Type on which Storming operations will be performed. |
| 1.3.6.1.4.1.164.3.1.6.1.5.1.1.5 | ColumnethIfStormCtrlEnable | read-write | current | This object indicates if the Storm Controling is Enabled or Disabled for the relevant entry. |
| 1.3.6.1.4.1.164.3.1.6.1.5.1.1.6 | ColumnethIfStormMaxRate | read-write | current | This object indicates the Maximum Rate at which Storming packets are forwarded, in Kbps.For some devices the units are PPS(Packets Per Second ) or kilobytes pe… |
| 1.3.6.1.4.1.164.3.1.6.1.6 | NodeethIfOamEfm | |||
| 1.3.6.1.4.1.164.3.1.6.1.6.0 | Nodedot3OamEvents | |||
| 1.3.6.1.4.1.164.3.1.6.1.6.0.1 | Notificationdot3OamOperStatusChange | current | This trap is sent when OAM EFM Link goes Up or Down. Up - is considered when dot3OamOperStatus value changes to operational(9) from any other value. Down - is … | |
| 1.3.6.1.4.1.164.3.1.6.1.6.0.2 | Notificationdot3OamPeerEvent | current | This trap is sent when value of dot3OamXPeerState changes from any value to one of the following values: linkFault, dyingGasp, criticalEvent. This trap has no … | |
| 1.3.6.1.4.1.164.3.1.6.1.6.1 | Tabledot3OamDescrTable | not-accessible | current | This table supports definitions of Descriptors (profiles) of OAM EFM Links. |
| 1.3.6.1.4.1.164.3.1.6.1.6.1.1 | Rowdot3OamDescrEntry | not-accessible | current | Each entry corresponds to a single OAM EFM Descriptor (profile). Each Descriptor contains a set of OAM EFM Link configuration parameters. The configuration par… |
| 1.3.6.1.4.1.164.3.1.6.1.6.1.1.1 | Columndot3OamDescrId | not-accessible | current | This object is the unique index associated with this Descriptor (profile). Entries in this table are referenced via the object dot3OamXDescrId in dot3OamXEntry. |
| 1.3.6.1.4.1.164.3.1.6.1.6.1.1.2 | Columndot3OamDescrRowStatus | read-create | current | This object controls creation/deletion of the associated entry in this table per the semantics of RowStatus. If an active entry is referenced in dot3OamXDescrI… |
| 1.3.6.1.4.1.164.3.1.6.1.6.1.1.3 | Columndot3OamDescrMode | read-create | current | This object controls the mode of OAM operation for an Ethernet-like interface referencing this Descriptor. OAM on Ethernet interfaces may be in 'active' mode o… |
| 1.3.6.1.4.1.164.3.1.6.1.6.1.1.4 | Columndot3OamDescrLbRxOperation | read-create | current | Since OAM loopback is a disruptive operation (user traffic does not pass), this object provides a mechanism to provide control: whether received OAM loopback c… |
| 1.3.6.1.4.1.164.3.1.6.1.6.1.1.5 | Columndot3OamDescrRateLimit | read-create | current | This object defines how many OAM frames can be sent per second (maximum) for an OAM EFM Link referencing this Descriptor. |
| 1.3.6.1.4.1.164.3.1.6.1.6.2 | Tabledot3OamXTable | not-accessible | current | This table is an extension of dot3OamTable of standard DOT3-OAM-MIB. |
| 1.3.6.1.4.1.164.3.1.6.1.6.2.1 | Rowdot3OamXEntry | not-accessible | current | An entry in dot3OamXTable. |
| 1.3.6.1.4.1.164.3.1.6.1.6.2.1.1 | Columndot3OamXDescrId | read-write | current | This object points to an entry of dot3OamDescrTable (dot3OamDescrId), which defines part of the configuration parameters for this OAM EFM Link. As long as one … |
| 1.3.6.1.4.1.164.3.1.6.1.6.2.1.2 | Columndot3OamXPeerState | read-only | current | This object reports the state of the Peer of the OAM EFM Link. unknown - at the initialization of the device, or after Reset, when there is still no data about… |
| 1.3.6.1.4.1.164.3.1.6.1.7 | NodeethIfMacLayer | |||
| 1.3.6.1.4.1.164.3.1.6.1.7.0 | NodeethIfMacLayerEvents | |||
| 1.3.6.1.4.1.164.3.1.6.1.7.0.1 | NotificationethIfMacAccessViolation | current | This trap indicates that an Access Violation occurred. | |
| 1.3.6.1.4.1.164.3.1.6.1.7.1 | TableethIfSrcMacCtrlTable | not-accessible | current | This table supports source MAC addresses control parameters per interface. Source MAC control will be used mainly for security. Only packets with certain sourc… |
| 1.3.6.1.4.1.164.3.1.6.1.7.1.1 | RowethIfSrcMacCtrlEntry | not-accessible | current | An entry in the table. |
| 1.3.6.1.4.1.164.3.1.6.1.7.1.1.1 | ColumnethIfSrcMacCtrlIndex | not-accessible | current | The index of the MAC Layer interface supporting source MAC control feature. It may be the ifIndex of the ETH/Bridge Port. |
| 1.3.6.1.4.1.164.3.1.6.1.7.1.1.2 | ColumnethIfSrcMacCtrlIdx2 | not-accessible | current | A second index that can be used. For example: The VLAN ID for which the source MAC control feature is supported. When this index is not in use, its value will … |
| 1.3.6.1.4.1.164.3.1.6.1.7.1.1.3 | ColumnethIfSrcMacCtrl | read-write | current | Enable or disable the source MAC control on the current interface. The device should not enable source MAC control if for the current interface there are more … |
| 1.3.6.1.4.1.164.3.1.6.1.7.1.1.4 | ColumnethIfSrcMacCtrlMaxPermitAddr | read-write | current | This is the maximum number of permitted MAC addresses (static and learned) for the current interface. |
| 1.3.6.1.4.1.164.3.1.6.1.7.1.1.5 | ColumnethIfSrcMacCtrlCurNumPermitAddr | read-only | current | This is the number of source MAC addresses currently permitted for the current interface. |
| 1.3.6.1.4.1.164.3.1.6.1.7.1.1.6 | ColumnethIfSrcMacCtrlFlushAddrCmd | read-write | current | When set to on (3) this command will erase all the learned addresses and invalid addresses of the selected interface in the ethIfSrcMacCtrlAddrTable. After ope… |
| 1.3.6.1.4.1.164.3.1.6.1.7.1.1.7 | ColumnethIfSrcMacCtrlAging | read-write | current | The timeout period in seconds for aging out dynamically learned source MAC addresses. Valid Values: 0 - disable 10-1000000 |
| 1.3.6.1.4.1.164.3.1.6.1.7.1.1.8 | ColumnethIfSrcMacCtrlLocking | read-write | current | When set to lock (3) this command will lock the Source MAC Address learning. No more learned addresses will be added to the ethIfSrcMacCtrlAddrTable. When set … |
| 1.3.6.1.4.1.164.3.1.6.1.7.1.1.9 | ColumnethIfSrcMacCtrlViolationAction | read-write | current | Determines the action that the device will take upon security violation. drop(2) - the violating packets will be dropped. dropNotify (3)- the violating packets… |
| 1.3.6.1.4.1.164.3.1.6.1.7.1.1.10 | ColumnethIfSrcMacCtrlLastViolatingAddr | read-write | current | This object indicates the last MAC address that violated the security on the current interface. If no violation, the agent will return: 00-00-00-00-00-00 . |
| 1.3.6.1.4.1.164.3.1.6.1.7.1.1.11 | ColumnethIfSrcMacCtrlPortStatus | read-only | current | This object represents the operational status of the MAC Control feature on an interface. shutdown(2) - This indicates that the port is shutdown due to securit… |
| 1.3.6.1.4.1.164.3.1.6.1.7.2 | TableethIfSrcMacCtrlAddrTable | not-accessible | current | This table shows which MAC Addresses are permitted when the source MAC control is enabled and which non permitted MAC Addresses attempted to access the current… |
| 1.3.6.1.4.1.164.3.1.6.1.7.2.1 | RowethIfSrcMacCtrlAddrEntry | not-accessible | current | An entry in the table. |
| 1.3.6.1.4.1.164.3.1.6.1.7.2.1.1 | ColumnethIfSrcMacCtrlAddrIndex | not-accessible | current | The index of the interface for which the source MAC addresses exist in this table. It may be the ifIndex of the ETH/Bridge Port. |
| 1.3.6.1.4.1.164.3.1.6.1.7.2.1.2 | ColumnethIfSrcMacCtrlAddr | not-accessible | current | A unicast source MAC address that was learned or statically configured for the current interface. Packets with this source MAC address will be accepted by the … |
| 1.3.6.1.4.1.164.3.1.6.1.7.2.1.3 | ColumnethIfSrcMacCtrlAddrIdx3 | not-accessible | current | A third index that can be used. For example: The VLAN ID for which the source MAC control feature is supported. When this index is not in use, its value will b… |
| 1.3.6.1.4.1.164.3.1.6.1.7.2.1.4 | ColumnethIfSrcMacCtrlAddrRowStatus | read-write | current | This MIB object will be used in order to create/delete a static row or delete an address that is not allowed to access the current interface (ethIfSrcMacCtrlAd… |
| 1.3.6.1.4.1.164.3.1.6.1.7.2.1.5 | ColumnethIfSrcMacCtrlAddrStatus | read-only | current | The status of this entry. The meanings of the values are: invalid (2) - the current address is not allowed to access this interface. learned(3) - the current a… |
| 1.3.6.1.4.1.164.3.1.6.1.11 | NodeethIfSysConfig | |||
| 1.3.6.1.4.1.164.3.1.6.1.11.1 | TableethIfSysValidEtherTypeTable | not-accessible | current | The table contains list of valid VLAN Tag Ethertype codes that may be used in port and flow configuration. The table is used by devices that can process limite… |
| 1.3.6.1.4.1.164.3.1.6.1.11.1.1 | RowethIfSysValidEtherTypeEntry | not-accessible | current | An entry in the Ethertype table. Each entry contains one valid Ethernet code. |
| 1.3.6.1.4.1.164.3.1.6.1.11.1.1.1 | ColumnethIfSysValidEtherTypeIdx | not-accessible | current | This is a running index of the configuration table. |
| 1.3.6.1.4.1.164.3.1.6.1.11.1.1.2 | ColumnethIfSysValidEtherTypeRowStatus | read-create | current | This object enables creation and deletion of entries in the ethIfSysValidEtherTypeTable. |
| 1.3.6.1.4.1.164.3.1.6.1.11.1.1.3 | ColumnethIfSysValidEtherTypeCode | read-create | current | The valid Ethertype code. See standards.ieee.org/regauth/ethertype/eth.txt for codes. |