MIB Viewer

RAD-RadShdsl-MIB

49 objects
SHDSL MIB.
Imported Objects
HDSL2-SHDSL-LINE-MIBhdsl2ShdslEndpointCurr15MinCRCanomalies hdsl2ShdslEndpointCurr15MinLOSWS hdsl2ShdslEndpointCurrAtn hdsl2ShdslEndpointCurrEntry hdsl2ShdslEndpointCurrSnrMgn hdsl2ShdslEndpointSide hdsl2ShdslEndpointThreshCRCanomalies hdsl2ShdslEndpointThreshLoopAttenuation hdsl2ShdslEndpointThreshLOSWS hdsl2ShdslEndpointThreshSNRMargin hdsl2ShdslInvIndex hdsl2ShdslSpanConfProfileEntry
IF-MIBifAlias ifIndex
RAD-GEN-MIBalarmEventLogAlarmOrEventId alarmEventLogDateAndTime alarmEventLogDescription alarmEventLogSeverity alarmEventLogSourceName alarmEventReason
RAD-SMI-MIBdiverseIfWanGen
SNMPv2-SMIInteger32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE TimeTicks Unsigned32
OIDNameAccessStatusDescription
1.3.6.1.4.1.164.3.1.6.12IdentityshdslIfSHDSL MIB.
1.3.6.1.4.1.164.3.1.6.12.0NoderadHdsl2ShdslEvents
1.3.6.1.4.1.164.3.1.6.12.0.1NotificationradHdsl2ShdslLoopBackTrapcurrentThis notification indicates that a remote loopback has been activated on the Embedded Operations Channel (EOC) of the SHDSL link.
1.3.6.1.4.1.164.3.1.6.12.0.13NotificationshdslLoswcurrentThis trap indicates Loss of sync word (LOSW) .
1.3.6.1.4.1.164.3.1.6.12.0.15NotificationshdslExcessiveCrcErrorcurrentThis trap indicates Excessive Crc Error.
1.3.6.1.4.1.164.3.1.6.12.0.19NotificationshdslLoopAttenuationOracurrentThis trap indicates that Loop attenuation has exceeded the threshold.
1.3.6.1.4.1.164.3.1.6.12.0.20NotificationshdslSnrMarginOracurrentThis trap indicates Signal-to-noise ratio (SNR) margin is below the threshold.
1.3.6.1.4.1.164.3.1.6.12.0.23NotificationshdslLinkDowncurrentThis trap indicates that the Link is down.
1.3.6.1.4.1.164.3.1.6.12.1TableshdslEndpointCurrTablenot-accessiblecurrentThis table is an extension of hdsl2ShdslEndpointCurrTable of rfc4319 It contains current status and performance information for segment endpoints in HDSL2/SHDS…
1.3.6.1.4.1.164.3.1.6.12.1.1RowshdslEndpointCurrEntrynot-accessiblecurrentAn entry in the shdslEndpointCurrTable. Each entry contains status and performance information relating to a single segment endpoint. It is indexed by the ifIn…
1.3.6.1.4.1.164.3.1.6.12.1.1.1Columnhdsl2ShdslEndpointCurrRcvGainread-onlycurrentThe current receive gain in hundredth of dB.
1.3.6.1.4.1.164.3.1.6.12.1.1.2Columnhdsl2ShdslEndpointCurrTransPowerread-onlycurrentThe current transmit power in tenth of dBm.
1.3.6.1.4.1.164.3.1.6.12.1.1.3Columnhdsl2ShdslEndpointCurrPowerBOread-onlycurrentThe current transceiver actual power backoff from 0dB to 31dB.
1.3.6.1.4.1.164.3.1.6.12.1.1.4Columnhdsl2ShdslEndpointCurrLineStatusread-onlycurrentThe current line synchronization status.
1.3.6.1.4.1.164.3.1.6.12.1.1.5Columnhdsl2ShdslEndpointCurrOpStateread-onlycurrentThe current operational state.
1.3.6.1.4.1.164.3.1.6.12.1.1.6Columnhdsl2ShdslEndpointAccumulatedTimeElapsedread-onlycurrentThe time (in hundredths of a second) since the accumulated counters were last re-initialized: Accumulated counters are hdsl2ShdslEndpointES, hdsl2ShdslEndpoint…
1.3.6.1.4.1.164.3.1.6.12.1.1.7Columnhdsl2ShdslEndpointCurrPsdread-onlycurrentThis object indicates use of symmetric/asymmetric PSD (Power Spectral Density) Mask for the associated SHDSL Line.
1.3.6.1.4.1.164.3.1.6.12.1.1.8Columnhdsl2ShdslEndpointValidIntervalsread-onlycurrentThe number of previous 15 minutes intervals for which valid data was collected.
1.3.6.1.4.1.164.3.1.6.12.1.1.9Columnhdsl2ShdslEndpointValidDaysIntervalsread-onlycurrentThe number of previous Days intervals for which valid data was collected.
1.3.6.1.4.1.164.3.1.6.12.2TableshdslEndpointMaintTablenot-accessiblecurrentThis table supports maintenance operations (eg. loopbacks) to be performed on HDSL2/SHDSL segment endpoints. This table contains live data from equipment. As s…
1.3.6.1.4.1.164.3.1.6.12.2.1RowshdslEndpointMaintEntrynot-accessiblecurrentAn entry in the hdsl2ShdslEndpointMaintTable. Each entry corresponds to a single segment endpoint, and is indexed by the ifIndex of the HDSL2/SHDSL line, the U…
1.3.6.1.4.1.164.3.1.6.12.2.1.1ColumnshdslMaintPowerBackOffread-writecurrentThis object configures the receiver at the associated segment endpoint to operate in default or enhanced power backoff mode. powerbackoff may also be disabled
1.3.6.1.4.1.164.3.1.6.12.3TableshdslSpanConfProfileTablenot-accessiblecurrentThis table supports definitions of span configuration profiles for SHDSL lines. HDSL2 does not support these configuration options. This table MUST be maintain…
1.3.6.1.4.1.164.3.1.6.12.3.1RowshdslSpanConfProfileEntrynot-accessiblecurrentEach entry corresponds to a single span configuration profile. Each profile contains a set of span configuration parameters. The configuration parameters in a …
1.3.6.1.4.1.164.3.1.6.12.3.1.1Columnhdsl2ShdslSpanConfEocCompatibleread-onlycurrentThis object indicate if device supports only standard EOC messages or also proprietary messages.
1.3.6.1.4.1.164.3.1.6.12.3.1.2Columnhdsl2ShdslSpanConfAsymmetricPSDRateread-writecurrentThis object indicates line rate when rfc3276.hdsl2ShdslSpanConfPSD value is asymmetric(2). Seleceted rate depends on transmission mode - specified in Annex A o…
1.3.6.1.4.1.164.3.1.6.12.3.1.3Columnhdsl2ShdslSpanConfWireInterfaceUsedread-writecurrentThis object enable user to configure SHDSL port with 4 wires to use 2 or 4 wires, or to auto detect far end number of wires
1.3.6.1.4.1.164.3.1.6.12.3.1.4Columnhdsl2ShdslSpanConfHandshakeread-writecurrentThis object indicates the Handshake Procedure.
1.3.6.1.4.1.164.3.1.6.12.4Nodehdsl2ShdslIfConf
1.3.6.1.4.1.164.3.1.6.12.4.1Tablehdsl2ShdslIfConfTablenot-accessiblecurrentThis table enables configuration of HDSL2/SHDSL interfaces per configuration index. Write operation for products supporting Active+Temp configurations, is poss…
1.3.6.1.4.1.164.3.1.6.12.4.1.1Rowhdsl2ShdslIfConfEntrynot-accessiblecurrentAn entry in the hdsl2ShdslIfConfTable.
1.3.6.1.4.1.164.3.1.6.12.4.1.1.1Columnhdsl2ShdslIfConfIdxread-onlycurrentThis object indicates the Idx of the Config being accessed. Idx of 255 relates to the Temporary (Scratch) Config. Write operation for products supporting Activ…
1.3.6.1.4.1.164.3.1.6.12.4.1.1.2Columnhdsl2ShdslSideIdxread-onlycurrentThis object indicates the Side of the managed object: Near-End or Far-End.
1.3.6.1.4.1.164.3.1.6.12.4.1.1.3Columnhdsl2ShdslMaxBwread-writecurrentMaximum BW (Bandwidth) of the Shdsl Line, in Kbps units. Respective Max No. of TSs = Max. Rate/64 This object can be Set only for a Central (xtuC) unit.
1.3.6.1.4.1.164.3.1.6.12.4.1.1.4Columnhdsl2ShdslPwrBackoffread-writecurrentThis object configures the receiver at the associated segment endpoint to enable/disable power backoff mode. This object is similar to hdsl2ShdslMaintPowerBack…
1.3.6.1.4.1.164.3.1.6.12.4.1.1.5Columnhdsl2ShdslTxModeread-writecurrentThis object configures the Transmission Mode for the SHDSL Line. Normally, This object can be Set only for a Central (xtuC) unit.
1.3.6.1.4.1.164.3.1.6.12.4.1.1.6Columnhdsl2ShdslAttenuationThresholdread-writecurrentThis object configures the Attentuation alarm threshold. 0=Off Valid values: 0..127 .
1.3.6.1.4.1.164.3.1.6.12.4.1.1.7Columnhdsl2ShdslSnrMarginThresholdread-writecurrentThis object configures the SNR margin alarm threshold. 0=Off Valid values: 0..15 .
1.3.6.1.4.1.164.3.1.6.12.4.1.1.8Columnhdsl2ShdslTs0OverDslread-writecurrentThis object configures the way TS0 will be treated over the SHDSL Line. looped - looped inside transparent - sent transparently over the DSL Line. This object …
1.3.6.1.4.1.164.3.1.6.12.4.1.1.9Columnhdsl2ShdslModeread-writecurrentThis object is relevant only for the Near-End device. stuC - Central stuR - Remote .
1.3.6.1.4.1.164.3.1.6.12.4.1.1.10Columnhdsl2ShdslTsCompactionModeread-writecurrentThis object configures how TSs will be compacted over the SHDSL Line. In both mapping cases (2),(3), only the TSs connected on the E1 line will be transferred …
1.3.6.1.4.1.164.3.1.6.12.4.1.1.11Columnhdsl2ShdslEocEnableread-writecurrentThis object configures whether EOC protocol is supported by the Far-End device working with this port.
1.3.6.1.4.1.164.3.1.6.12.4.1.1.12Columnhdsl2ShdslFar1stIfNumOfTSsread-writecurrentThis object configures the number of TSs of the SHDSL line that belong to the 1st Interface of the Far-End device, where 1st means that these TSs are first on …
1.3.6.1.4.1.164.3.1.6.12.4.1.1.13Columnhdsl2ShdslFarEndDeviceread-writecurrentThis object indicates the Far-End device. It is used for 2 purposes: - in order to know if EOC is used (EOC is used only when the device is any of the ASMi52 o…
1.3.6.1.4.1.164.3.1.6.12.4.1.1.14Columnhdsl2ShdslPwrBackoffDbread-writecurrentThis object configures the Power Backoff (in dB) of the receiver, at the associated segment endpoint. 0=Off Valid values: 0..31 .
1.3.6.1.4.1.164.3.1.6.12.4.1.1.15Columnhdsl2ShdslFarEndMuxTsaread-writecurrentThis object represents Assignment of E1 TSs to Far-End MUX Interfaces. It is relevant only when hdsl2ShdslSideIdx=nearEnd(2), when for the Near-End device, hds…
1.3.6.1.4.1.164.3.1.6.12.4.1.1.16Columnhdsl2ShdslLineProbeEnableread-writecurrentThis object enables/disables support for Line Probe of the units in an SHDSL line. When Line Probe is enabled, the system performs Line Probing to find the bes…
1.3.6.1.4.1.164.3.1.6.12.4.1.1.17Columnhdsl2ShdslClockModeread-writecurrentThis object enables configuration of the clock mode. (1) - 1 Plesiochronous (e.g. ASMi-52 / ASMi-54L) (2) - 2 Plesiochronous with timing reference (e.g. ASMi-5…
1.3.6.1.4.1.164.3.1.6.12.4.1.1.19Columnhdsl2ShdslIfConfLinkDownReasonread-onlycurrent
MIB Viewer