REDLINE-AN50-MIB
114 objects
No module-level DESCRIPTION found.
Imported Objects
| REDLINE-AN50-PMP-V1-MIB | an50pmpLastMissedSsMacAddress an50pmpLastModifiedCID an50pmpLastRegisteredSsMacAddress |
| RFC-1212 | OBJECT-TYPE |
| RFC-1215 | TRAP-TYPE |
| RFC1155-SMI | Counter enterprises IpAddress TimeTicks |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.10728 | Noderedline | |||
| 1.3.6.1.4.1.10728.1 | Nodean50TftpFailTrap | An event to report the failure of a Software Download. | ||
| 1.3.6.1.4.1.10728.1 | NoderedlineProducts | |||
| 1.3.6.1.4.1.10728.2 | Nodean50TftpSuccessTrap | An event to report the success of a Software Download. | ||
| 1.3.6.1.4.1.10728.2 | NoderedlineMgmt | |||
| 1.3.6.1.4.1.10728.2.16 | NoderedlineAn50 | |||
| 1.3.6.1.4.1.10728.2.16.1 | Nodean50General | |||
| 1.3.6.1.4.1.10728.2.16.1.1 | Scalaran50GenUBR | read-only | mandatory | Indicates the system's current uncoded burst rate. With adaptive modulation enabled, this rate may change over time, depending on the prevailing propagation co… |
| 1.3.6.1.4.1.10728.2.16.1.2 | Scalaran50GenRFLink | read-only | mandatory | connected(2) indicates the terminal is communicating properly to the remote terminal. notConnected(1) indicates there is no communication with the remote termi… |
| 1.3.6.1.4.1.10728.2.16.1.3 | Scalaran50GenFrequency | read-write | mandatory | The frequency which represents the operating channel of the link. The system can be configured to operate over 9 distinct channels. |
| 1.3.6.1.4.1.10728.2.16.1.4 | Scalaran50GenAllignmentMode | read-write | mandatory | Specifies if the antenna alignment is done with buzzer or voltage. |
| 1.3.6.1.4.1.10728.2.16.1.5 | Scalaran50GenEncryptionEnabled | read-write | mandatory | Specifies if encryption is enabled or not. |
| 1.3.6.1.4.1.10728.2.16.1.6 | Scalaran50GenFlowControlEnabled | read-write | mandatory | This attribute specifies if flow control is enabled or not. |
| 1.3.6.1.4.1.10728.2.16.1.7 | Scalaran50GenHttpAccessEnabled | read-write | mandatory | This attribute specifies if Http Access is enabled or not. |
| 1.3.6.1.4.1.10728.2.16.1.8 | Scalaran50GenTelnetAccessEnabled | read-write | mandatory | This attribute specifies if Telnet Access is enabled or not. |
| 1.3.6.1.4.1.10728.2.16.1.9 | Scalaran50GenTelnetPort | read-write | mandatory | This attribute specifies the Telnet port number. |
| 1.3.6.1.4.1.10728.2.16.1.10 | Scalaran50GenOptionsKey | read-write | mandatory | This attribute specifies the Product Options Key. |
| 1.3.6.1.4.1.10728.2.16.1.11 | Scalaran50GenResetDevice | read-write | mandatory | reset(2) indicates to reset the AN50 terminal. donothing(1) indicates do not reset AN50 terminal. |
| 1.3.6.1.4.1.10728.2.16.1.12 | Scalaran50GenFault | read-only | mandatory | The attribute specifies the Fault LED status of the terminal. |
| 1.3.6.1.4.1.10728.2.16.1.13 | Scalaran50GenTxPower | read-only | mandatory | This object specifies the actual Tx Power of the AN-50 Node in ? |
| 1.3.6.1.4.1.10728.2.16.1.14 | Scalaran50GenRegisteredStations | read-only | mandatory | This object specifies the actual number of configured links. |
| 1.3.6.1.4.1.10728.2.16.1.15 | Scalaran50GenRegisteredConnections | read-only | mandatory | This object specifies the actual number of configured connections. |
| 1.3.6.1.4.1.10728.2.16.1.16 | Scalaran50GenActiveWirelessLinks | read-only | mandatory | This object specifies the actual number of provisioned links. |
| 1.3.6.1.4.1.10728.2.16.1.17 | Scalaran50GenChannelAutoScan | read-write | mandatory | This object specifies the Auto-Scanning feature for the channel. |
| 1.3.6.1.4.1.10728.2.16.1.18 | Scalaran50GenIduType | read-only | mandatory | This object specifies the Indoor Unit Type. |
| 1.3.6.1.4.1.10728.2.16.1.19 | Scalaran50GenOduType | read-only | mandatory | This object specifies the Outdoor Unit Type. |
| 1.3.6.1.4.1.10728.2.16.2 | Nodean50Config | |||
| 1.3.6.1.4.1.10728.2.16.2.1 | Nodean50ConfigEther | |||
| 1.3.6.1.4.1.10728.2.16.2.1.1 | Scalaran50EtherMacAddress | read-only | mandatory | This object specifies the Ethernet MAC address of the local terminal. |
| 1.3.6.1.4.1.10728.2.16.2.1.2 | Scalaran50EtherGateway | read-write | mandatory | The IP Gateway of the AN-50 This field is used to specify the IP address of the gateway which the AN-50 is communicating through the core network. |
| 1.3.6.1.4.1.10728.2.16.2.1.3 | Scalaran50EtherPortStatus | read-only | mandatory | The attribute specifies the status of the Ethernet Port of the AN50. |
| 1.3.6.1.4.1.10728.2.16.2.1.4 | Scalaran50EtherIP | read-write | mandatory | The IP address of the AN-50. The default address from the factory is 192.168.25.2. For the initial set-up, the terminal should not be connected to the Internet… |
| 1.3.6.1.4.1.10728.2.16.2.1.5 | Scalaran50EtherMask | read-write | mandatory | The IP Subnet Mask of the AN-50. The value is typically set to 255.255.255.0 (Class C subnet), which prevents certain local devices from going out into the wir… |
| 1.3.6.1.4.1.10728.2.16.2.1.6 | Scalaran50Ether100 | read-only | mandatory | This object specifies the 100 Mb/s Ethernet LED status of the AN50. |
| 1.3.6.1.4.1.10728.2.16.2.1.7 | Scalaran50EtherFd | read-only | mandatory | The object specifies the Ethernet FullDuplex LED status of the AN50. |
| 1.3.6.1.4.1.10728.2.16.2.1.8 | Scalaran50EtherMgmVidEn | read-write | mandatory | The attribute specifies the Ethernet Management Vlan Enabled Status of the AN50. |
| 1.3.6.1.4.1.10728.2.16.2.1.9 | Scalaran50EtherMgmVid | read-write | mandatory | The attribute specifies the Ethernet Management Vlan Id of the AN50. |
| 1.3.6.1.4.1.10728.2.16.2.1.10 | Scalaran50EtherLben | read-write | mandatory | The attribute specifies the Link Backup Enable Status of the AN50. |
| 1.3.6.1.4.1.10728.2.16.2.2 | Nodean50ConfigWireless | |||
| 1.3.6.1.4.1.10728.2.16.2.2.1 | Scalaran50WrlsChannel | read-write | mandatory | specifies the operating channel of the system, within the 100 MHz available in the 5.8GHz UNII band. To avoid interference, two PTP links operating in the same… |
| 1.3.6.1.4.1.10728.2.16.2.2.2 | Scalaran50WrlsTxPower | read-write | mandatory | The Tx Power of the AN-50 in dBm. Specifies the power level of the system, which is preset at the factory and should not be altered. In the event that this par… |
| 1.3.6.1.4.1.10728.2.16.2.2.3 | Scalaran50WrlsModReduction | read-write | mandatory | The Modulation Reduction Level of the AN-50. Applies when the Adaptive rate is disabled. Specifies how many levels the system must drop in modulation before be… |
| 1.3.6.1.4.1.10728.2.16.2.2.4 | Scalaran50WrlsAdaptiveMod | read-write | mandatory | Setting this attribute to AdaptiveRate(2) sets the system to operate in adaptive modulation mode. It is recommended to keep the AN-50 in this mode so that the … |
| 1.3.6.1.4.1.10728.2.16.2.2.5 | Scalaran50WrlsUBR | read-write | mandatory | This object contains the desired net uncoded burst rate for the link. Set uncoded burst rate in steps (0=6Mb/s, 1=9Mb/s, 2=12Mb/s, 3=18Mb/s, 4=24Mb/s, 5=36Mb/s… |
| 1.3.6.1.4.1.10728.2.16.2.2.6 | Scalaran50WrlsMaster | read-write | mandatory | The object contains the configured mode of the AN50 terminal. 1 = PTP Slave, 2 = PTP Master, 3 = PMP Slave, 4 = PMP Master |
| 1.3.6.1.4.1.10728.2.16.2.2.7 | Scalaran50WrlsVersion | read-write | mandatory | Sets the version of the AN50 system software. The software can be remotely downloaded into the AN50. The system comprises sufficient memory to hold two indepen… |
| 1.3.6.1.4.1.10728.2.16.2.2.8 | Scalaran50WrlsEncryptCode | read-write | mandatory | The object contains the Encryption Key used for the AN-50 terminal. Enter the MAC address of the remote terminal to enable over-the-air data encryption. |
| 1.3.6.1.4.1.10728.2.16.2.2.9 | Scalaran50WrlsCableAttenuation | read-only | mandatory | This object contains the Cable Attenuation for the AN-50 in dB. |
| 1.3.6.1.4.1.10728.2.16.2.2.10 | Scalaran50WrlsRfPortStatus | read-only | mandatory | The object specifies the status of the AN50s Wireless Port. |
| 1.3.6.1.4.1.10728.2.16.2.2.11 | Scalaran50WrlsSaveConfig | read-write | mandatory | The object saves the entire config set of the AN50. |
| 1.3.6.1.4.1.10728.2.16.2.2.12 | Scalaran50WrlsActivateConfig | read-write | mandatory | The object activates the entire config set of the AN50. |
| 1.3.6.1.4.1.10728.2.16.2.2.13 | Scalaran50WrlsRadioEnable | read-write | mandatory | The object specifies whether radio transmission is enabled or disabled. |
| 1.3.6.1.4.1.10728.2.16.2.2.14 | Scalaran50WrlsRfStatusErrorCode | read-only | mandatory | The object specifies the Error Code for the RF Status. |
| 1.3.6.1.4.1.10728.2.16.2.2.15 | Scalaran50WrlsRfSignal | read-only | mandatory | The object specifies the Wireless Signal LED status. |
| 1.3.6.1.4.1.10728.2.16.2.2.16 | Scalaran50WrlsLLMode | read-write | mandatory | Link length set mode. |
| 1.3.6.1.4.1.10728.2.16.2.2.17 | Scalaran50WrlsLMU | read-write | mandatory | This object specifies the Link measurements unit (mile / Km). |
| 1.3.6.1.4.1.10728.2.16.2.2.18 | Scalaran50WrlsLL | read-write | mandatory | This object specifies the Link Length. See an50WrlsLMU object for units. |
| 1.3.6.1.4.1.10728.2.16.2.2.19 | Nodean50ConfigScheduler | |||
| 1.3.6.1.4.1.10728.2.16.2.2.19.1 | Scalaran50WrlsFrameSize | read-write | mandatory | This object specifies the size of wireless frame (DL+RTD+UL) in micro seconds. |
| 1.3.6.1.4.1.10728.2.16.2.2.19.2 | Scalaran50WrlsMinBlockSize | read-write | mandatory | This object specifies a minimum number of bytes comprising transmitted block. |
| 1.3.6.1.4.1.10728.2.16.2.2.19.3 | Scalaran50WrlsDownlinkSize | read-write | mandatory | This object specifies the size of downlink sub-frame in micro seconds. |
| 1.3.6.1.4.1.10728.2.16.2.2.19.4 | Scalaran50WrlsRoundTripDelay | read-write | mandatory | This object specifies the round trip delay in micro seconds. |
| 1.3.6.1.4.1.10728.2.16.2.2.19.5 | Scalaran50WrlsAdaptiveDLSize | read-write | mandatory | This object specifies if adaptive downlink size is enabled or disabled. |
| 1.3.6.1.4.1.10728.2.16.2.2.19.6 | Scalaran50WrlsExtSyncronize | read-write | mandatory | This object specifies if external synchronization is enabled or disabled. |
| 1.3.6.1.4.1.10728.2.16.2.2.19.7 | Scalaran50WrlsMaximumDistance | read-write | mandatory | This object specifies the maximum distance between base station and subscriber station in Km. |
| 1.3.6.1.4.1.10728.2.16.2.2.19.8 | Scalaran50WrlsRegistrationPeriod | read-write | mandatory | This object specifies the number of frames between registration periods. |
| 1.3.6.1.4.1.10728.2.16.2.2.20 | Nodean50ConfigDefGroup | |||
| 1.3.6.1.4.1.10728.2.16.2.2.20.1 | Scalaran50WrlsBroadcastDLCIR | read-write | mandatory | This object specifies the broadcast downlink commited rate in kb/s. |
| 1.3.6.1.4.1.10728.2.16.2.2.20.2 | Scalaran50WrlsBroadcastDLPIR | read-write | mandatory | This object specifies the broadcast downlink peak rate in kb/s. |
| 1.3.6.1.4.1.10728.2.16.2.2.21 | Scalaran50WrlsDFSAction | read-write | mandatory | This object specifies the action taken when another system is detected on the same frequency |
| 1.3.6.1.4.1.10728.2.16.2.2.22 | Scalaran50WrlsAntennaGain | read-write | mandatory | Antenna Gain in dB. |
| 1.3.6.1.4.1.10728.2.16.2.2.23 | Scalaran50WrlsATPEnabled | read-write | mandatory | This object specifies if the Automatic Transmitted Power Control is enabled |
| 1.3.6.1.4.1.10728.2.16.2.3 | Nodean50Sw | |||
| 1.3.6.1.4.1.10728.2.16.2.3.1 | Scalaran50SwServer | read-write | mandatory | The address of the TFTP server used for software upgrades. If the address of the TFTP server is unknown, return 0.0.0.0. |
| 1.3.6.1.4.1.10728.2.16.2.3.2 | Scalaran50SwFilename | read-write | mandatory | The file name of the software image to be loaded into this device. |
| 1.3.6.1.4.1.10728.2.16.2.3.3 | Scalaran50SwAdminStatus | read-write | mandatory | If set to upgrade(2), the device will initiate a TFTP software image download using an50SwFilename. If the download process is interrupted by a reset or power … |
| 1.3.6.1.4.1.10728.2.16.2.3.4 | Scalaran50SwOperStatus | read-only | mandatory | This object shows the download status. inProgress(1) indicates that a TFTP download is underway completeSuccess(2) indicates that the last software upgrade was… |
| 1.3.6.1.4.1.10728.2.16.2.3.5 | Scalaran50SwCurrentVers | read-only | mandatory | The software version currently operating in this device's flash. This object should be in the syntax used by the individual vendor to identify software version… |
| 1.3.6.1.4.1.10728.2.16.2.3.6 | Scalaran50SwOtherVers | read-only | mandatory | The software version in the secondary flash. This object should be in the syntax used by the individual vendor to identify software versions. If it is not appl… |
| 1.3.6.1.4.1.10728.2.16.3 | Nodean50Pm | |||
| 1.3.6.1.4.1.10728.2.16.3.1 | Scalaran50ResetStatistics | read-write | mandatory | A value of reset(2) resets the performance statistics on the AN-50, a value of donothing(1) does nothing. |
| 1.3.6.1.4.1.10728.2.16.3.2 | Nodean50PmEther | |||
| 1.3.6.1.4.1.10728.2.16.3.2.1 | Scalaran50PmEtherRxPackets | read-only | mandatory | This object counts the number of ethernet packets successfully received by the local system. |
| 1.3.6.1.4.1.10728.2.16.3.2.2 | Scalaran50PmEtherRxPacketsErr | read-only | mandatory | This object counts the number of ethernet packet errors received by the local system. |
| 1.3.6.1.4.1.10728.2.16.3.2.3 | Scalaran50PmEtherTxPackets | read-only | mandatory | This object counts the number of Ethernet packets transmitted by the local system. |
| 1.3.6.1.4.1.10728.2.16.3.2.4 | Scalaran50PmEtherTxPacketsErr | read-only | mandatory | This object counts the number of Ethernet error packets transmitted by the local system. |
| 1.3.6.1.4.1.10728.2.16.3.2.5 | Scalaran50PmEtherRxPacketsDisc | read-only | mandatory | This object counts the number of ethernet packets discarded by receiver. |
| 1.3.6.1.4.1.10728.2.16.3.2.6 | Scalaran50PmEtherTxPacketsDisc | read-only | mandatory | This object counts the number of ethernet packets discarded by transmitter. |
| 1.3.6.1.4.1.10728.2.16.3.3 | Nodean50PmWrls | |||
| 1.3.6.1.4.1.10728.2.16.3.3.1 | Scalaran50PmWrlsRxSigMin | read-only | mandatory | This object indicates the minimum received signal strength measured since the last SNMP update. |
| 1.3.6.1.4.1.10728.2.16.3.3.2 | Scalaran50PmWrlsRxSigMean | read-only | mandatory | This object indicates the average received signal strength measured since the last SNMP update. |
| 1.3.6.1.4.1.10728.2.16.3.3.3 | Scalaran50PmWrlsRxSigMax | read-only | mandatory | This object indicates the maximum received signal strength measured since the last SNMP update |
| 1.3.6.1.4.1.10728.2.16.3.3.4 | Scalaran50PmWrlsAvgSinAdr | read-only | mandatory | This object indicates the average signal to noise ratio measured since the last SNMP update. The ratio is based on the digital information provided from the ou… |
| 1.3.6.1.4.1.10728.2.16.3.3.5 | Scalaran50PmWrlsRxPackets | read-only | mandatory | This object indicates the number of packets received over the air from the remote terminal. |
| 1.3.6.1.4.1.10728.2.16.3.3.6 | Scalaran50PmWrlsRxPacketsRetx | read-only | mandatory | This object indicates the number of packets retransmitted over the air from the remoter terminal. |
| 1.3.6.1.4.1.10728.2.16.3.3.7 | Scalaran50PmWrlsRxPacketsDisc | read-only | mandatory | This object indicates the number of packets, originating from the remote terminal lost over the air due to degradation in the RF link. |
| 1.3.6.1.4.1.10728.2.16.3.3.8 | Scalaran50PmWrlsTxPackets | read-only | mandatory | This object indicates the number of wireless packets (including Ethernet frames and error correction bytes) transmitted over the air by the local terminal. |
| 1.3.6.1.4.1.10728.2.16.3.3.9 | Scalaran50PmWrlsTxPacketsRetx | read-only | mandatory | This object indicates the number of packets retransmitted over the air by the local terminal. The retransmission scheme is based on the Acknowledge/Request (AR… |
| 1.3.6.1.4.1.10728.2.16.3.3.10 | Scalaran50PmWrlsTxPacketsDisc | read-only | mandatory | This object indicates the total number of packets lost over the air due to degradation in the RF link. |
| 1.3.6.1.4.1.10728.2.16.3.3.11 | Scalaran50PmWrlsCalcDst | read-only | mandatory | This object contains the calculated link distance. |
| 1.3.6.1.4.1.10728.2.16.4 | Nodean50Trap | |||
| 1.3.6.1.4.1.10728.2.16.4.1 | Scalaran50SysLastTrapTime | read-only | mandatory | The value of system.sysUpTime when the last trap was generated. If no traps have been generated since the last reset, this attribute has a value of 0. No trap … |
| 1.3.6.1.4.1.10728.2.16.5 | Nodean50LinkPmp | |||
| 1.3.6.1.4.1.10728.2.16.5.1 | Scalaran50MaxCid | read-only | mandatory | The object contains the maximum number of CID for this equipment |
| 1.3.6.1.4.1.10728.2.16.5.2 | Scalaran50LinkCurrentAvailId | read-only | mandatory | The current available ID in the Links table that is queried by NMS before creating a new row in Link Table |
| 1.3.6.1.4.1.10728.3 | Nodean50PswdChangeFailTrap | An event to report the failure of a password change. | ||
| 1.3.6.1.4.1.10728.4 | Nodean50FirmwareConfigFailTrap | An event to report the failure of a firmware config. | ||
| 1.3.6.1.4.1.10728.5 | Nodean50EepromCorruptedTrap | An event to report the corruption of the EEPROM. | ||
| 1.3.6.1.4.1.10728.6 | Nodean50PowerSupplyFailureTrap | An event to report the power supply failure. | ||
| 1.3.6.1.4.1.10728.7 | Nodean50SaveConfigTrap | An event to report the saving of configuration | ||
| 1.3.6.1.4.1.10728.8 | Nodean50ModifiedIDTrap | An event to report the modification in the configuration of a CID | ||
| 1.3.6.1.4.1.10728.9 | Nodean50pmpRegistrationMissed | An event to report the missing of the registration by a AN50 Subscriber to one BS.This trap is sent by the BS and contains the MAC address of the SS missing th… | ||
| 1.3.6.1.4.1.10728.10 | Nodean50pmpRegistrationSuccessful | An event to report the successful registration of an AN50 Subscriber to BS. This trap is sent by the BS and contains the MAC address of the newly registered SS | ||
| 1.3.6.1.4.1.10728.11 | Nodean50DFSEvent | An event to report a dynamic frequency selection (DFS) event in AN50 |