RSVP-MIB
170 objects
The MIB module to describe the RSVP Protocol
Imported Objects
| IF-MIB | ifIndex InterfaceIndex |
| INTEGRATED-SERVICES-MIB | BitRate BurstSize intSrvFlowStatus MessageSize Port Protocol QosService SessionNumber SessionType |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Gauge32 Integer32 mib-2 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE |
| SNMPv2-TC | RowStatus TestAndIncr TEXTUAL-CONVENTION TimeInterval TimeStamp TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.2.1.51 | Identityrsvp | The MIB module to describe the RSVP Protocol | ||
| 1.3.6.1.2.1.51.1 | NodersvpObjects | |||
| 1.3.6.1.2.1.51.1.1 | TablersvpSessionTable | not-accessible | current | A table of all sessions seen by a given system. |
| 1.3.6.1.2.1.51.1.1.1 | RowrsvpSessionEntry | not-accessible | current | A single session seen by a given system. |
| 1.3.6.1.2.1.51.1.1.1.1 | ColumnrsvpSessionNumber | not-accessible | current | The number of this session. This is for SNMP Indexing purposes only and has no relation to any protocol value. |
| 1.3.6.1.2.1.51.1.1.1.2 | ColumnrsvpSessionType | read-only | current | The type of session (IP4, IP6, IP6 with flow information, etc). |
| 1.3.6.1.2.1.51.1.1.1.3 | ColumnrsvpSessionDestAddr | read-only | current | The destination address used by all senders in this session. This object may not be changed when the value of the RowStatus object is 'active'. |
| 1.3.6.1.2.1.51.1.1.1.4 | ColumnrsvpSessionDestAddrLength | read-only | current | The CIDR prefix length of the session address, which is 32 for IP4 host and multicast addresses, and 128 for IP6 addresses. This object may not be changed when… |
| 1.3.6.1.2.1.51.1.1.1.5 | ColumnrsvpSessionProtocol | read-only | current | The IP Protocol used by this session. This object may not be changed when the value of the RowStatus object is 'active'. |
| 1.3.6.1.2.1.51.1.1.1.6 | ColumnrsvpSessionPort | read-only | current | The UDP or TCP port number used as a destination port for all senders in this session. If the IP protocol in use, specified by rsvpSenderProtocol, is 50 (ESP) … |
| 1.3.6.1.2.1.51.1.1.1.7 | ColumnrsvpSessionSenders | read-only | current | The number of distinct senders currently known to be part of this session. |
| 1.3.6.1.2.1.51.1.1.1.8 | ColumnrsvpSessionReceivers | read-only | current | The number of reservations being requested of this system for this session. |
| 1.3.6.1.2.1.51.1.1.1.9 | ColumnrsvpSessionRequests | read-only | current | The number of reservation requests this system is sending upstream for this session. |
| 1.3.6.1.2.1.51.1.2 | TablersvpSenderTable | not-accessible | current | Information describing the state information displayed by senders in PATH messages. |
| 1.3.6.1.2.1.51.1.2.1 | RowrsvpSenderEntry | not-accessible | current | Information describing the state information displayed by a single sender's PATH message. |
| 1.3.6.1.2.1.51.1.2.1.1 | ColumnrsvpSenderNumber | not-accessible | current | The number of this sender. This is for SNMP Indexing purposes only and has no relation to any protocol value. |
| 1.3.6.1.2.1.51.1.2.1.2 | ColumnrsvpSenderType | read-create | current | The type of session (IP4, IP6, IP6 with flow information, etc). |
| 1.3.6.1.2.1.51.1.2.1.3 | ColumnrsvpSenderDestAddr | read-create | current | The destination address used by all senders in this session. This object may not be changed when the value of the RowStatus object is 'active'. |
| 1.3.6.1.2.1.51.1.2.1.4 | ColumnrsvpSenderAddr | read-create | current | The source address used by this sender in this session. This object may not be changed when the value of the RowStatus object is 'active'. |
| 1.3.6.1.2.1.51.1.2.1.5 | ColumnrsvpSenderDestAddrLength | read-create | current | The length of the destination address in bits. This is the CIDR Prefix Length, which for IP4 hosts and multicast addresses is 32 bits. This object may not be c… |
| 1.3.6.1.2.1.51.1.2.1.6 | ColumnrsvpSenderAddrLength | read-create | current | The length of the sender's address in bits. This is the CIDR Prefix Length, which for IP4 hosts and multicast addresses is 32 bits. This object may not be chan… |
| 1.3.6.1.2.1.51.1.2.1.7 | ColumnrsvpSenderProtocol | read-create | current | The IP Protocol used by this session. This object may not be changed when the value of the RowStatus object is 'active'. |
| 1.3.6.1.2.1.51.1.2.1.8 | ColumnrsvpSenderDestPort | read-create | current | The UDP or TCP port number used as a destination port for all senders in this session. If the IP protocol in use, specified by rsvpSenderProtocol, is 50 (ESP) … |
| 1.3.6.1.2.1.51.1.2.1.9 | ColumnrsvpSenderPort | read-create | current | The UDP or TCP port number used as a source port for this sender in this session. If the IP protocol in use, specified by rsvpSenderProtocol is 50 (ESP) or 51 … |
| 1.3.6.1.2.1.51.1.2.1.10 | ColumnrsvpSenderFlowId | read-only | current | The flow ID that this sender is using, if this is an IPv6 session. |
| 1.3.6.1.2.1.51.1.2.1.11 | ColumnrsvpSenderHopAddr | read-create | current | The address used by the previous RSVP hop (which may be the original sender). |
| 1.3.6.1.2.1.51.1.2.1.12 | ColumnrsvpSenderHopLih | read-create | current | The Logical Interface Handle used by the previous RSVP hop (which may be the original sender). |
| 1.3.6.1.2.1.51.1.2.1.13 | ColumnrsvpSenderInterface | read-create | current | The ifIndex value of the interface on which this PATH message was most recently received. |
| 1.3.6.1.2.1.51.1.2.1.14 | ColumnrsvpSenderTSpecRate | read-create | current | The Average Bit Rate of the sender's data stream. Within a transmission burst, the arrival rate may be as fast as rsvpSenderTSpecPeakRate (if supported by the … |
| 1.3.6.1.2.1.51.1.2.1.15 | ColumnrsvpSenderTSpecPeakRate | read-create | current | The Peak Bit Rate of the sender's data stream. Traffic arrival is not expected to exceed this rate at any time, apart from the effects of jitter in the network… |
| 1.3.6.1.2.1.51.1.2.1.16 | ColumnrsvpSenderTSpecBurst | read-create | current | The size of the largest burst expected from the sender at a time. |
| 1.3.6.1.2.1.51.1.2.1.17 | ColumnrsvpSenderTSpecMinTU | read-create | current | The minimum message size for this flow. The policing algorithm will treat smaller messages as though they are this size. |
| 1.3.6.1.2.1.51.1.2.1.18 | ColumnrsvpSenderTSpecMaxTU | read-create | current | The maximum message size for this flow. The admission algorithm will reject TSpecs whose Maximum Transmission Unit, plus the interface headers, exceed the inte… |
| 1.3.6.1.2.1.51.1.2.1.19 | ColumnrsvpSenderInterval | read-create | current | The interval between refresh messages as advertised by the Previous Hop. |
| 1.3.6.1.2.1.51.1.2.1.20 | ColumnrsvpSenderRSVPHop | read-create | current | If TRUE, the node believes that the previous IP hop is an RSVP hop. If FALSE, the node believes that the previous IP hop may not be an RSVP hop. |
| 1.3.6.1.2.1.51.1.2.1.21 | ColumnrsvpSenderLastChange | read-only | current | The time of the last change in this PATH message; This is either the first time it was received or the time of the most recent change in parameters. |
| 1.3.6.1.2.1.51.1.2.1.22 | ColumnrsvpSenderPolicy | read-create | current | The contents of the policy object, displayed as an uninterpreted string of octets, including the object header. In the absence of such an object, this should b… |
| 1.3.6.1.2.1.51.1.2.1.23 | ColumnrsvpSenderAdspecBreak | read-create | current | The global break bit general characterization parameter from the ADSPEC. If TRUE, at least one non-IS hop was detected in the path. If FALSE, no non-IS hops we… |
| 1.3.6.1.2.1.51.1.2.1.24 | ColumnrsvpSenderAdspecHopCount | read-create | current | The hop count general characterization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following conditions: the invalid bit wa… |
| 1.3.6.1.2.1.51.1.2.1.25 | ColumnrsvpSenderAdspecPathBw | read-create | current | The path bandwidth estimate general characterization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following conditions: the … |
| 1.3.6.1.2.1.51.1.2.1.26 | ColumnrsvpSenderAdspecMinLatency | read-create | current | The minimum path latency general characterization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following conditions: the inv… |
| 1.3.6.1.2.1.51.1.2.1.27 | ColumnrsvpSenderAdspecMtu | read-create | current | The composed Maximum Transmission Unit general characterization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following condi… |
| 1.3.6.1.2.1.51.1.2.1.28 | ColumnrsvpSenderAdspecGuaranteedSvc | read-create | current | If TRUE, the ADSPEC contains a Guaranteed Service fragment. If FALSE, the ADSPEC does not contain a Guaranteed Service fragment. |
| 1.3.6.1.2.1.51.1.2.1.29 | ColumnrsvpSenderAdspecGuaranteedBreak | read-create | current | If TRUE, the Guaranteed Service fragment has its 'break' bit set, indicating that one or more nodes along the path do not support the guaranteed service. If FA… |
| 1.3.6.1.2.1.51.1.2.1.30 | ColumnrsvpSenderAdspecGuaranteedCtot | read-create | current | If rsvpSenderAdspecGuaranteedSvc is TRUE, this is the end-to-end composed value for the guaranteed service 'C' parameter. A return of zero or noSuchValue indic… |
| 1.3.6.1.2.1.51.1.2.1.31 | ColumnrsvpSenderAdspecGuaranteedDtot | read-create | current | If rsvpSenderAdspecGuaranteedSvc is TRUE, this is the end-to-end composed value for the guaranteed service 'D' parameter. A return of zero or noSuchValue indic… |
| 1.3.6.1.2.1.51.1.2.1.32 | ColumnrsvpSenderAdspecGuaranteedCsum | read-create | current | If rsvpSenderAdspecGuaranteedSvc is TRUE, this is the composed value for the guaranteed service 'C' parameter since the last reshaping point. A return of zero … |
| 1.3.6.1.2.1.51.1.2.1.33 | ColumnrsvpSenderAdspecGuaranteedDsum | read-create | current | If rsvpSenderAdspecGuaranteedSvc is TRUE, this is the composed value for the guaranteed service 'D' parameter since the last reshaping point. A return of zero … |
| 1.3.6.1.2.1.51.1.2.1.34 | ColumnrsvpSenderAdspecGuaranteedHopCount | read-create | current | If rsvpSenderAdspecGuaranteedSvc is TRUE, this is the service-specific override of the hop count general characterization parameter from the ADSPEC. A return o… |
| 1.3.6.1.2.1.51.1.2.1.35 | ColumnrsvpSenderAdspecGuaranteedPathBw | read-create | current | If rsvpSenderAdspecGuaranteedSvc is TRUE, this is the service-specific override of the path bandwidth estimate general characterization parameter from the ADSP… |
| 1.3.6.1.2.1.51.1.2.1.36 | ColumnrsvpSenderAdspecGuaranteedMinLatency | read-create | current | If rsvpSenderAdspecGuaranteedSvc is TRUE, this is the service-specific override of the minimum path latency general characterization parameter from the ADSPEC.… |
| 1.3.6.1.2.1.51.1.2.1.37 | ColumnrsvpSenderAdspecGuaranteedMtu | read-create | current | If rsvpSenderAdspecGuaranteedSvc is TRUE, this is the service-specific override of the composed Maximum Transmission Unit general characterization parameter fr… |
| 1.3.6.1.2.1.51.1.2.1.38 | ColumnrsvpSenderAdspecCtrlLoadSvc | read-create | current | If TRUE, the ADSPEC contains a Controlled Load Service fragment. If FALSE, the ADSPEC does not contain a Controlled Load Service fragment. |
| 1.3.6.1.2.1.51.1.2.1.39 | ColumnrsvpSenderAdspecCtrlLoadBreak | read-create | current | If TRUE, the Controlled Load Service fragment has its 'break' bit set, indicating that one or more nodes along the path do not support the controlled load serv… |
| 1.3.6.1.2.1.51.1.2.1.40 | ColumnrsvpSenderAdspecCtrlLoadHopCount | read-create | current | If rsvpSenderAdspecCtrlLoadSvc is TRUE, this is the service-specific override of the hop count general characterization parameter from the ADSPEC. A return of … |
| 1.3.6.1.2.1.51.1.2.1.41 | ColumnrsvpSenderAdspecCtrlLoadPathBw | read-create | current | If rsvpSenderAdspecCtrlLoadSvc is TRUE, this is the service-specific override of the path bandwidth estimate general characterization parameter from the ADSPEC… |
| 1.3.6.1.2.1.51.1.2.1.42 | ColumnrsvpSenderAdspecCtrlLoadMinLatency | read-create | current | If rsvpSenderAdspecCtrlLoadSvc is TRUE, this is the service-specific override of the minimum path latency general characterization parameter from the ADSPEC. A… |
| 1.3.6.1.2.1.51.1.2.1.43 | ColumnrsvpSenderAdspecCtrlLoadMtu | read-create | current | If rsvpSenderAdspecCtrlLoadSvc is TRUE, this is the service-specific override of the composed Maximum Transmission Unit general characterization parameter from… |
| 1.3.6.1.2.1.51.1.2.1.44 | ColumnrsvpSenderStatus | read-create | current | 'active' for all active PATH messages. This object may be used to install static PATH information or delete PATH information. |
| 1.3.6.1.2.1.51.1.2.1.45 | ColumnrsvpSenderTTL | read-only | current | The TTL value in the RSVP header that was last received. |
| 1.3.6.1.2.1.51.1.3 | TablersvpSenderOutInterfaceTable | not-accessible | current | List of outgoing interfaces that PATH messages use. The ifIndex is the ifIndex value of the egress interface. |
| 1.3.6.1.2.1.51.1.3.1 | RowrsvpSenderOutInterfaceEntry | not-accessible | current | List of outgoing interfaces that a particular PATH message has. |
| 1.3.6.1.2.1.51.1.3.1.1 | ColumnrsvpSenderOutInterfaceStatus | read-only | current | 'active' for all active PATH messages. |
| 1.3.6.1.2.1.51.1.4 | TablersvpResvTable | not-accessible | current | Information describing the state information displayed by receivers in RESV messages. |
| 1.3.6.1.2.1.51.1.4.1 | RowrsvpResvEntry | not-accessible | current | Information describing the state information displayed by a single receiver's RESV message concerning a single sender. |
| 1.3.6.1.2.1.51.1.4.1.1 | ColumnrsvpResvNumber | not-accessible | current | The number of this reservation request. This is for SNMP Indexing purposes only and has no relation to any protocol value. |
| 1.3.6.1.2.1.51.1.4.1.2 | ColumnrsvpResvType | read-create | current | The type of session (IP4, IP6, IP6 with flow information, etc). |
| 1.3.6.1.2.1.51.1.4.1.3 | ColumnrsvpResvDestAddr | read-create | current | The destination address used by all senders in this session. This object may not be changed when the value of the RowStatus object is 'active'. |
| 1.3.6.1.2.1.51.1.4.1.4 | ColumnrsvpResvSenderAddr | read-create | current | The source address of the sender selected by this reservation. The value of all zeroes indicates 'all senders'. This object may not be changed when the value o… |
| 1.3.6.1.2.1.51.1.4.1.5 | ColumnrsvpResvDestAddrLength | read-create | current | The length of the destination address in bits. This is the CIDR Prefix Length, which for IP4 hosts and multicast addresses is 32 bits. This object may not be c… |
| 1.3.6.1.2.1.51.1.4.1.6 | ColumnrsvpResvSenderAddrLength | read-create | current | The length of the sender's address in bits. This is the CIDR Prefix Length, which for IP4 hosts and multicast addresses is 32 bits. This object may not be chan… |
| 1.3.6.1.2.1.51.1.4.1.7 | ColumnrsvpResvProtocol | read-create | current | The IP Protocol used by this session. This object may not be changed when the value of the RowStatus object is 'active'. |
| 1.3.6.1.2.1.51.1.4.1.8 | ColumnrsvpResvDestPort | read-create | current | The UDP or TCP port number used as a destination port for all senders in this session. If the IP protocol in use, specified by rsvpResvProtocol, is 50 (ESP) or… |
| 1.3.6.1.2.1.51.1.4.1.9 | ColumnrsvpResvPort | read-create | current | The UDP or TCP port number used as a source port for this sender in this session. If the IP protocol in use, specified by rsvpResvProtocol is 50 (ESP) or 51 (A… |
| 1.3.6.1.2.1.51.1.4.1.10 | ColumnrsvpResvHopAddr | read-create | current | The address used by the next RSVP hop (which may be the ultimate receiver). |
| 1.3.6.1.2.1.51.1.4.1.11 | ColumnrsvpResvHopLih | read-create | current | The Logical Interface Handle received from the previous RSVP hop (which may be the ultimate receiver). |
| 1.3.6.1.2.1.51.1.4.1.12 | ColumnrsvpResvInterface | read-create | current | The ifIndex value of the interface on which this RESV message was most recently received. |
| 1.3.6.1.2.1.51.1.4.1.13 | ColumnrsvpResvService | read-create | current | The QoS Service classification requested by the receiver. |
| 1.3.6.1.2.1.51.1.4.1.14 | ColumnrsvpResvTSpecRate | read-create | current | The Average Bit Rate of the sender's data stream. Within a transmission burst, the arrival rate may be as fast as rsvpResvTSpecPeakRate (if supported by the se… |
| 1.3.6.1.2.1.51.1.4.1.15 | ColumnrsvpResvTSpecPeakRate | read-create | current | The Peak Bit Rate of the sender's data stream. Traffic arrival is not expected to exceed this rate at any time, apart from the effects of jitter in the network… |
| 1.3.6.1.2.1.51.1.4.1.16 | ColumnrsvpResvTSpecBurst | read-create | current | The size of the largest burst expected from the sender at a time. If this is less than the sender's advertised burst size, the receiver is asking the network t… |
| 1.3.6.1.2.1.51.1.4.1.17 | ColumnrsvpResvTSpecMinTU | read-create | current | The minimum message size for this flow. The policing algorithm will treat smaller messages as though they are this size. |
| 1.3.6.1.2.1.51.1.4.1.18 | ColumnrsvpResvTSpecMaxTU | read-create | current | The maximum message size for this flow. The admission algorithm will reject TSpecs whose Maximum Transmission Unit, plus the interface headers, exceed the inte… |
| 1.3.6.1.2.1.51.1.4.1.19 | ColumnrsvpResvRSpecRate | read-create | current | If the requested service is Guaranteed, as specified by rsvpResvService, this is the clearing rate that is being requested. Otherwise, it is zero, or the agent… |
| 1.3.6.1.2.1.51.1.4.1.20 | ColumnrsvpResvRSpecSlack | read-create | current | If the requested service is Guaranteed, as specified by rsvpResvService, this is the delay slack. Otherwise, it is zero, or the agent may return noSuchValue. |
| 1.3.6.1.2.1.51.1.4.1.21 | ColumnrsvpResvInterval | read-create | current | The interval between refresh messages as advertised by the Next Hop. |
| 1.3.6.1.2.1.51.1.4.1.22 | ColumnrsvpResvScope | read-create | current | The contents of the scope object, displayed as an uninterpreted string of octets, including the object header. In the absence of such an object, this should be… |
| 1.3.6.1.2.1.51.1.4.1.23 | ColumnrsvpResvShared | read-create | current | If TRUE, a reservation shared among senders is requested. If FALSE, a reservation specific to this sender is requested. |
| 1.3.6.1.2.1.51.1.4.1.24 | ColumnrsvpResvExplicit | read-create | current | If TRUE, individual senders are listed using Filter Specifications. If FALSE, all senders are implicitly selected. The Scope Object will contain a list of send… |
| 1.3.6.1.2.1.51.1.4.1.25 | ColumnrsvpResvRSVPHop | read-create | current | If TRUE, the node believes that the previous IP hop is an RSVP hop. If FALSE, the node believes that the previous IP hop may not be an RSVP hop. |
| 1.3.6.1.2.1.51.1.4.1.26 | ColumnrsvpResvLastChange | read-only | current | The time of the last change in this reservation request; This is either the first time it was received or the time of the most recent change in parameters. |
| 1.3.6.1.2.1.51.1.4.1.27 | ColumnrsvpResvPolicy | read-create | current | The contents of the policy object, displayed as an uninterpreted string of octets, including the object header. In the absence of such an object, this should b… |
| 1.3.6.1.2.1.51.1.4.1.28 | ColumnrsvpResvStatus | read-create | current | 'active' for all active RESV messages. This object may be used to install static RESV information or delete RESV information. |
| 1.3.6.1.2.1.51.1.4.1.29 | ColumnrsvpResvTTL | read-only | current | The TTL value in the RSVP header that was last received. |
| 1.3.6.1.2.1.51.1.4.1.30 | ColumnrsvpResvFlowId | read-only | current | The flow ID that this receiver is using, if this is an IPv6 session. |
| 1.3.6.1.2.1.51.1.5 | TablersvpResvFwdTable | not-accessible | current | Information describing the state information displayed upstream in RESV messages. |
| 1.3.6.1.2.1.51.1.5.1 | RowrsvpResvFwdEntry | not-accessible | current | Information describing the state information displayed upstream in an RESV message concerning a single sender. |
| 1.3.6.1.2.1.51.1.5.1.1 | ColumnrsvpResvFwdNumber | not-accessible | current | The number of this reservation request. This is for SNMP Indexing purposes only and has no relation to any protocol value. |
| 1.3.6.1.2.1.51.1.5.1.2 | ColumnrsvpResvFwdType | read-only | current | The type of session (IP4, IP6, IP6 with flow information, etc). |
| 1.3.6.1.2.1.51.1.5.1.3 | ColumnrsvpResvFwdDestAddr | read-only | current | The destination address used by all senders in this session. This object may not be changed when the value of the RowStatus object is 'active'. |
| 1.3.6.1.2.1.51.1.5.1.4 | ColumnrsvpResvFwdSenderAddr | read-only | current | The source address of the sender selected by this reservation. The value of all zeroes indicates 'all senders'. This object may not be changed when the value o… |
| 1.3.6.1.2.1.51.1.5.1.5 | ColumnrsvpResvFwdDestAddrLength | read-only | current | The length of the destination address in bits. This is the CIDR Prefix Length, which for IP4 hosts and multicast addresses is 32 bits. This object may not be c… |
| 1.3.6.1.2.1.51.1.5.1.6 | ColumnrsvpResvFwdSenderAddrLength | read-only | current | The length of the sender's address in bits. This is the CIDR Prefix Length, which for IP4 hosts and multicast addresses is 32 bits. This object may not be chan… |
| 1.3.6.1.2.1.51.1.5.1.7 | ColumnrsvpResvFwdProtocol | read-only | current | The IP Protocol used by a session. for secure sessions, this indicates IP Security. This object may not be changed when the value of the RowStatus object is 'a… |
| 1.3.6.1.2.1.51.1.5.1.8 | ColumnrsvpResvFwdDestPort | read-only | current | The UDP or TCP port number used as a destination port for all senders in this session. If the IP protocol in use, specified by rsvpResvFwdProtocol, is 50 (ESP)… |
| 1.3.6.1.2.1.51.1.5.1.9 | ColumnrsvpResvFwdPort | read-only | current | The UDP or TCP port number used as a source port for this sender in this session. If the IP protocol in use, specified by rsvpResvFwdProtocol is 50 (ESP) or 51… |
| 1.3.6.1.2.1.51.1.5.1.10 | ColumnrsvpResvFwdHopAddr | read-only | current | The address of the (previous) RSVP that will receive this message. |
| 1.3.6.1.2.1.51.1.5.1.11 | ColumnrsvpResvFwdHopLih | read-only | current | The Logical Interface Handle sent to the (previous) RSVP that will receive this message. |
| 1.3.6.1.2.1.51.1.5.1.12 | ColumnrsvpResvFwdInterface | read-only | current | The ifIndex value of the interface on which this RESV message was most recently sent. |
| 1.3.6.1.2.1.51.1.5.1.13 | ColumnrsvpResvFwdService | read-only | current | The QoS Service classification requested. |
| 1.3.6.1.2.1.51.1.5.1.14 | ColumnrsvpResvFwdTSpecRate | read-only | current | The Average Bit Rate of the sender's data stream. Within a transmission burst, the arrival rate may be as fast as rsvpResvFwdTSpecPeakRate (if supported by the… |
| 1.3.6.1.2.1.51.1.5.1.15 | ColumnrsvpResvFwdTSpecPeakRate | read-only | current | The Peak Bit Rate of the sender's data stream Traffic arrival is not expected to exceed this rate at any time, apart from the effects of jitter in the network.… |
| 1.3.6.1.2.1.51.1.5.1.16 | ColumnrsvpResvFwdTSpecBurst | read-only | current | The size of the largest burst expected from the sender at a time. If this is less than the sender's advertised burst size, the receiver is asking the network t… |
| 1.3.6.1.2.1.51.1.5.1.17 | ColumnrsvpResvFwdTSpecMinTU | read-only | current | The minimum message size for this flow. The policing algorithm will treat smaller messages as though they are this size. |
| 1.3.6.1.2.1.51.1.5.1.18 | ColumnrsvpResvFwdTSpecMaxTU | read-only | current | The maximum message size for this flow. The admission algorithm will reject TSpecs whose Maximum Transmission Unit, plus the interface headers, exceed the inte… |
| 1.3.6.1.2.1.51.1.5.1.19 | ColumnrsvpResvFwdRSpecRate | read-only | current | If the requested service is Guaranteed, as specified by rsvpResvService, this is the clearing rate that is being requested. Otherwise, it is zero, or the agent… |
| 1.3.6.1.2.1.51.1.5.1.20 | ColumnrsvpResvFwdRSpecSlack | read-only | current | If the requested service is Guaranteed, as specified by rsvpResvService, this is the delay slack. Otherwise, it is zero, or the agent may return noSuchValue. |
| 1.3.6.1.2.1.51.1.5.1.21 | ColumnrsvpResvFwdInterval | read-only | current | The interval between refresh messages advertised to the Previous Hop. |
| 1.3.6.1.2.1.51.1.5.1.22 | ColumnrsvpResvFwdScope | read-only | current | The contents of the scope object, displayed as an uninterpreted string of octets, including the object header. In the absence of such an object, this should be… |
| 1.3.6.1.2.1.51.1.5.1.23 | ColumnrsvpResvFwdShared | read-only | current | If TRUE, a reservation shared among senders is requested. If FALSE, a reservation specific to this sender is requested. |
| 1.3.6.1.2.1.51.1.5.1.24 | ColumnrsvpResvFwdExplicit | read-only | current | If TRUE, individual senders are listed using Filter Specifications. If FALSE, all senders are implicitly selected. The Scope Object will contain a list of send… |
| 1.3.6.1.2.1.51.1.5.1.25 | ColumnrsvpResvFwdRSVPHop | read-only | current | If TRUE, the node believes that the next IP hop is an RSVP hop. If FALSE, the node believes that the next IP hop may not be an RSVP hop. |
| 1.3.6.1.2.1.51.1.5.1.26 | ColumnrsvpResvFwdLastChange | read-only | current | The time of the last change in this request; This is either the first time it was sent or the time of the most recent change in parameters. |
| 1.3.6.1.2.1.51.1.5.1.27 | ColumnrsvpResvFwdPolicy | read-only | current | The contents of the policy object, displayed as an uninterpreted string of octets, including the object header. In the absence of such an object, this should b… |
| 1.3.6.1.2.1.51.1.5.1.28 | ColumnrsvpResvFwdStatus | read-write | current | 'active' for all active RESV messages. This object may be used to delete RESV information. |
| 1.3.6.1.2.1.51.1.5.1.29 | ColumnrsvpResvFwdTTL | read-only | current | The TTL value in the RSVP header that was last received. |
| 1.3.6.1.2.1.51.1.5.1.30 | ColumnrsvpResvFwdFlowId | read-only | current | The flow ID that this receiver is using, if this is an IPv6 session. |
| 1.3.6.1.2.1.51.1.6 | TablersvpIfTable | not-accessible | current | The RSVP-specific attributes of the system's interfaces. |
| 1.3.6.1.2.1.51.1.6.1 | RowrsvpIfEntry | not-accessible | current | The RSVP-specific attributes of the a given interface. |
| 1.3.6.1.2.1.51.1.6.1.1 | ColumnrsvpIfUdpNbrs | read-only | current | The number of neighbors perceived to be using only the RSVP UDP Encapsulation. |
| 1.3.6.1.2.1.51.1.6.1.2 | ColumnrsvpIfIpNbrs | read-only | current | The number of neighbors perceived to be using only the RSVP IP Encapsulation. |
| 1.3.6.1.2.1.51.1.6.1.3 | ColumnrsvpIfNbrs | read-only | current | The number of neighbors currently perceived; this will exceed rsvpIfIpNbrs + rsvpIfUdpNbrs by the number of neighbors using both encapsulations. |
| 1.3.6.1.2.1.51.1.6.1.4 | ColumnrsvpIfRefreshBlockadeMultiple | read-create | current | The value of the RSVP value 'Kb', Which is the minimum number of refresh intervals that blockade state will last once entered. |
| 1.3.6.1.2.1.51.1.6.1.5 | ColumnrsvpIfRefreshMultiple | read-create | current | The value of the RSVP value 'K', which is the number of refresh intervals which must elapse (minimum) before a PATH or RESV message which is not being refreshe… |
| 1.3.6.1.2.1.51.1.6.1.6 | ColumnrsvpIfTTL | read-create | current | The value of SEND_TTL used on this interface for messages this node originates. If set to zero, the node determines the TTL via other means. |
| 1.3.6.1.2.1.51.1.6.1.7 | ColumnrsvpIfRefreshInterval | read-create | current | The value of the RSVP value 'R', which is the minimum period between refresh transmissions of a given PATH or RESV message on an interface. |
| 1.3.6.1.2.1.51.1.6.1.8 | ColumnrsvpIfRouteDelay | read-create | current | The approximate period from the time a route is changed to the time a resulting message appears on the interface. |
| 1.3.6.1.2.1.51.1.6.1.9 | ColumnrsvpIfEnabled | read-create | current | If TRUE, RSVP is enabled on this Interface. If FALSE, RSVP is not enabled on this interface. |
| 1.3.6.1.2.1.51.1.6.1.10 | ColumnrsvpIfUdpRequired | read-create | current | If TRUE, manual configuration forces the use of UDP encapsulation on the interface. If FALSE, UDP encapsulation is only used if rsvpIfUdpNbrs is not zero. |
| 1.3.6.1.2.1.51.1.6.1.11 | ColumnrsvpIfStatus | read-create | current | 'active' on interfaces that are configured for RSVP. |
| 1.3.6.1.2.1.51.1.7 | TablersvpNbrTable | not-accessible | current | Information describing the Neighbors of an RSVP system. |
| 1.3.6.1.2.1.51.1.7.1 | RowrsvpNbrEntry | not-accessible | current | Information describing a single RSVP Neighbor. |
| 1.3.6.1.2.1.51.1.7.1.1 | ColumnrsvpNbrAddress | not-accessible | current | The IP4 or IP6 Address used by this neighbor. This object may not be changed when the value of the RowStatus object is 'active'. |
| 1.3.6.1.2.1.51.1.7.1.2 | ColumnrsvpNbrProtocol | read-create | current | The encapsulation being used by this neighbor. |
| 1.3.6.1.2.1.51.1.7.1.3 | ColumnrsvpNbrStatus | read-create | current | 'active' for all neighbors. This object may be used to configure neighbors. In the presence of configured neighbors, the implementation may (but is not require… |
| 1.3.6.1.2.1.51.2 | NodersvpGenObjects | |||
| 1.3.6.1.2.1.51.2.1 | ScalarrsvpBadPackets | read-only | current | This object keeps a count of the number of bad RSVP packets received. |
| 1.3.6.1.2.1.51.2.2 | ScalarrsvpSenderNewIndex | read-write | current | This object is used to assign values to rsvpSenderNumber as described in 'Textual Conventions for SNMPv2'. The network manager reads the object, and then write… |
| 1.3.6.1.2.1.51.2.3 | ScalarrsvpResvNewIndex | read-write | current | This object is used to assign values to rsvpResvNumber as described in 'Textual Conventions for SNMPv2'. The network manager reads the object, and then writes … |
| 1.3.6.1.2.1.51.2.4 | ScalarrsvpResvFwdNewIndex | read-write | current | This object is used to assign values to rsvpResvFwdNumber as described in 'Textual Conventions for SNMPv2'. The network manager reads the object, and then writ… |
| 1.3.6.1.2.1.51.2.5 | ScalarrsvpSessionNewIndex | read-write | current | This object is used to assign values to rsvpSessionNumber as described in 'Textual Conventions for SNMPv2'. The network manager reads the object, and then writ… |
| 1.3.6.1.2.1.51.3 | NodersvpNotificationsPrefix | |||
| 1.3.6.1.2.1.51.3.0 | NodersvpNotifications | |||
| 1.3.6.1.2.1.51.3.0.1 | NotificationnewFlow | current | The newFlow trap indicates that the originating system has installed a new flow in its classifier, or (when reservation authorization is in view) is prepared t… | |
| 1.3.6.1.2.1.51.3.0.2 | NotificationlostFlow | current | The lostFlow trap indicates that the originating system has removed a flow from its classifier. | |
| 1.3.6.1.2.1.51.4 | NodersvpConformance | |||
| 1.3.6.1.2.1.51.4.1 | NodersvpGroups | |||
| 1.3.6.1.2.1.51.4.1.1 | GrouprsvpSessionGroup | current | These objects are required for RSVP Systems. | |
| 1.3.6.1.2.1.51.4.1.2 | GrouprsvpSenderGroup | current | These objects are required for RSVP Systems. | |
| 1.3.6.1.2.1.51.4.1.3 | GrouprsvpResvGroup | current | These objects are required for RSVP Systems. | |
| 1.3.6.1.2.1.51.4.1.4 | GrouprsvpResvFwdGroup | current | These objects are optional, used for some RSVP Systems. | |
| 1.3.6.1.2.1.51.4.1.5 | GrouprsvpIfGroup | current | These objects are required for RSVP Systems. | |
| 1.3.6.1.2.1.51.4.1.6 | GrouprsvpNbrGroup | current | These objects are required for RSVP Systems. | |
| 1.3.6.1.2.1.51.4.1.7 | GrouprsvpGenObjectsGroup | current | This objects are required for RSVP Systems. | |
| 1.3.6.1.2.1.51.4.1.8 | GrouprsvpSenderOutInterfaceGroup | current | These objects are required for RSVP Systems. | |
| 1.3.6.1.2.1.51.4.1.9 | GrouprsvpNotificationGroup | current | This notification is required for Systems supporting the RSVP Policy Module using an SNMP interface to the Policy Manager. | |
| 1.3.6.1.2.1.51.4.2 | NodersvpCompliances | |||
| 1.3.6.1.2.1.51.4.2.1 | CompliancersvpCompliance | not-accessible | current | The compliance statement. Note that the implementation of this module requires implementation of the Integrated Services MIB as well. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| RefreshInterval | INTEGER (0..'7FFFFFFF'h) | current | The number of milliseconds that are expected to elapse between refreshes of path or reservation state. Unrefreshed Path or reservation state is removed after a small multiple of this period. |
| RsvpEncapsulation | INTEGER { ip (1), udp (2), both (3) } | current | This indicates the encapsulation that an RSVP Neighbor is perceived to be using. |