TN-ACL-MIB
120 objects
The mib provides functionalities for ACL managing in TN modules.
Imported Objects
| ENTITY-MIB | entPhysicalIndex |
| IF-MIB | ifIndex InterfaceIndexOrZero |
| INET-ADDRESS-MIB | InetAddress |
| Q-BRIDGE-MIB | PortList VlanIdOrAny VlanIdOrAnyOrNone VlanIdOrNone |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | MacAddress RowStatus StorageType TEXTUAL-CONVENTION TruthValue |
| TN-MGMT-MIB | tnDevMgmt |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.868.2.5.3.1.1.5 | IdentitytnAclMgmt | The mib provides functionalities for ACL managing in TN modules. | ||
| 1.3.6.1.4.1.868.2.5.3.1.1.5.1 | TabletnAclPortTable | not-accessible | current | This table displays and sets the ACL parameters (ACE) of each switch port. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.1.1 | RowtnAclPortEntry | not-accessible | current | This entry represents an ACL port configuration. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.1.1.1 | ColumntnAclPortPolicyId | read-write | current | Select the policy to apply to this port. The allowed values are 0 through 255. The default value is 0. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.1.1.2 | ColumntnAclPortAction | read-write | current | Select the policy to apply to this port. The allowed values are 0 through 255. The default value is 0. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.1.1.3 | ColumntnAclPortRateLimiterId | read-write | current | Select which rate limiter to apply on this port. The allowed values are Disabled or the values 1 through 16. The default value is 'Disabled'. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.1.1.4 | ColumntnAclPortEvcPolicerState | read-write | current | Select whether EVC policer is enabled or disabled. The default value is 'Disabled'. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.1.1.5 | ColumntnAclPortEvcPolicerId | read-write | current | Select which EVC policer ID to apply on this port. when 'tnAclPortEvcPolicerState' is enabled, the valid value is from 1 to 128. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.1.1.6 | ColumntnAclPortRedirect | read-write | current | Select which port frames are redirected on. The allowed values is a specific port number and it can't be set when action is permitted. When no bit is selected,… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.1.1.7 | ColumntnAclPortMirrorState | read-write | current | Specify the mirror operation of this port. The allowed values are: Enabled: Frames received on the port are mirrored. Disabled: Frames received on the port are… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.1.1.8 | ColumntnAclPortLoggingState | read-write | current | Specify the logging operation of this port. The allowed values are: Enabled: Frames received on the port are stored in the System Log. Disabled: Frames receive… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.1.1.9 | ColumntnAclPortShutdownState | read-write | current | Specify the port shut down operation of this port. The allowed values are: Enabled: If a frame is received on the port, the port will be disabled. Disabled: Po… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.1.1.10 | ColumntnAclPortAclState | read-write | current | Specify the port state of this port. The allowed values are: Enabled: To reopen ports by changing the volatile port configuration of the ACL user module. Disab… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.1.1.11 | ColumntnAclPortCounter | read-only | current | Counts the number of frames that match this ACE. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.2 | TabletnAclRateLimiterTable | not-accessible | current | This table displays and sets the rate limiter for the ACL of the switch. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.2.1 | RowtnAclRateLimiterEntry | not-accessible | current | This entry represents an ACL rate limiter. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.2.1.1 | ColumntnAclRateLimitId | not-accessible | current | The rate limiter ID for the settings contained in the same row. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.2.1.2 | ColumntnAclRateLimitRate | read-write | current | The allowed values are: 0-3276700 in pps or 0, 100, 200, 300, ..., 1000000 in kbps. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.2.1.3 | ColumntnAclRateLimitUnit | read-write | current | Specify the rate unit. The allowed values are: pps: packets per second. kbps: Kbits per second. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.3 | TabletnAclOperTable | not-accessible | current | This table sets the ACL operation. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.3.1 | RowtnAclOperEntry | not-accessible | current | This entry represents an ACL operation. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.3.1.1 | ColumntnAclClearCounter | read-write | current | Specify ACL clear operation. The allowed values are: nooper: no operation. clear: Clear all ACL counters, including counts the number of frames that match this… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.4 | TabletnAceTable | not-accessible | current | This table contains the configuration of ACE(ACL control entry) of the switch. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.4.1 | RowtnAceEntry | not-accessible | current | This entry represents an ACE. Each entry in this table represents an ACE and can be created or deleted by the management system. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.4.1.1 | ColumntnAceIndex | not-accessible | current | The index of ACE. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.4.1.2 | ColumntnAceNextIndex | read-create | current | Specify the created ACE is placed before which ACE. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.4.1.3 | ColumntnAceIngressPort | read-create | current | Select the ingress port for which this ACE applies. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.4.1.4 | ColumntnAcePolicyFilterType | read-create | current | Specify the policy number filter for this ACE. Any: No policy filter is specified. (policy filter status is 'dont-care'.) Specific: If you want to filter a spe… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.4.1.5 | ColumntnAcePolicyValue | read-create | current | When 'Specific' is selected for the policy filter, you can enter a specific policy value. The allowed range is 0 to 255. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.4.1.6 | ColumntnAcePolicyBitMask | read-create | current | When 'Specific' is selected for the policy filter, you can enter a specific policy bitmask. The allowed range is 0x0 to 0xff. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.4.1.7 | ColumntnAcePolicyFrameType | read-create | current | Select the frame type for this ACE. These frame types are mutually exclusive. any: Any frame can match this ACE. etherType: Only Ethernet Type frames can match… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.4.1.8 | ColumntnAceAction | read-create | current | Specify the action to take with a frame that hits this ACE. permit: The frame that hits this ACE is granted permission for the ACE operation. deny: The frame t… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.4.1.9 | ColumntnAceRateLimiter | read-write | current | Specify the rate limiter in number of base units. The allowed range is 1 to 16. 'disabled' indicates that the rate limiter operation is disabled. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.4.1.10 | ColumntnAceEvcPolicerState | read-create | current | Select whether EVC policer is enabled or disabled. The default value is 'Disabled'. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.4.1.11 | ColumntnAceEvcPolicerId | read-create | current | Select which EVC policer ID to apply on this ACE. The allowed values are from 1 through 128. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.4.1.12 | ColumntnAcePortRedirect | read-create | current | Frames that hit the ACE are redirected to the port number specified here. The allowed range is the same as the switch port number range. 'disabled' indicates t… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.4.1.13 | ColumntnAceMirrorState | read-create | current | Specify the mirror operation of this port. Frames matching the ACE are mirrored to the destination mirror port. The allowed values are: Enabled: Frames receive… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.4.1.14 | ColumntnAceLoggingState | read-create | current | Specify the logging operation of the ACE. The allowed values are: Enabled: Frames matching the ACE are stored in the System Log. Disabled: Frames matching the … |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.4.1.15 | ColumntnAceShutdownState | read-create | current | Specify the port shut down operation of the ACE. The allowed values are: Enabled: If a frame matches the ACE, the ingress port will be disabled. Disabled: Port… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.4.1.16 | ColumntnAceCounter | read-only | current | The counter indicates the number of times the ACE was hit by a frame. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.4.1.17 | ColumntnAceVlan8021qTagged | read-create | current | Specify whether frames can hit the action according to the 802.1Q tagged. The allowed values are: any: Any value is allowed ('dont-care'). enabled: Tagged fram… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.4.1.18 | ColumntnAceVlanIdFilter | read-create | current | Specify the VLAN ID filter for this ACE. any: No VLAN ID filter is specified. (VLAN ID filter status is 'dont-care'.) specific: If you want to filter a specifi… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.4.1.19 | ColumntnAceVlanId | read-create | current | When 'Specific' is selected for the VLAN ID filter, you can enter a specific VLAN ID number. The allowed range is 1 to 4095. A frame that hits this ACE matches… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.4.1.20 | ColumntnAceTagPriority | read-create | current | Specify the tag priority for this ACE. A frame that hits this ACE matches this tag priority. The allowed number range is 0 to 7. The value Any means that no ta… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.4.1.21 | ColumntnAceRowStatus | read-create | current | The status of this conceptual row entry of ACE table. This object isused to manage the creation and deletion of conceptual rows. The status column has six defi… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.4.1.22 | ColumntnAceLookup | read-create | current | Specify the second lookup operation of the ACE. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.5 | TabletnAceEtherTable | not-accessible | current | This table contains the related configuration of ACE when frame type is etherType. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.5.1 | RowtnAceEtherEntry | not-accessible | current | This entry represents an etherType related ACE configuration. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.5.1.1 | ColumntnAceEtherSmacFilter | read-write | current | Specify the source MAC filter for this ACE. any: No SMAC filter is specified. (SMAC filter status is 'dont-care'.) specific: If you want to filter a specific s… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.5.1.2 | ColumntnAceEtherSmacVal | read-write | current | When 'Specific' is selected for the SMAC/DMAC filter, you can enter a specific value. The legal format is 'xx-xx-xx-xx-xx-xx' or 'xx.xx.xx.xx.xx.xx' or 'xxxxxx… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.5.1.3 | ColumntnAceEtherDmacFilter | read-write | current | Specify the destination MAC filter for this ACE. any: No DMAC filter is specified. (DMAC filter status is 'dont-care'.) unicast: Frame must be unicast. multica… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.5.1.4 | ColumntnAceEtherDmacVal | read-write | current | When 'Specific' is selected for the DMAC filter, you can enter a specific value. The legal format is 'xx-xx-xx-xx-xx-xx' or 'xx.xx.xx.xx.xx.xx' or 'xxxxxxxxxxx… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.5.1.5 | ColumntnAceEtherTypeFilter | read-write | current | Specify the Ethernet type filter for this ACE: any: No EtherType filter is specified. (EtherType filter status is 'don't-care'. specific: If you want to filter… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.5.1.6 | ColumntnAceEtherTypeVal | read-create | current | When 'Specific' is selected for the EtherType filter, you can enter a specific EtherType value. The allowed range is 0x600 to 0xFFFF but excluding 0x800(IPv4),… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.6 | TabletnAceArpTable | not-accessible | current | This table contains the related configuration of ACE when frame type is ARP. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.6.1 | RowtnAceArpEntry | not-accessible | current | This entry represents an ARP related ACE configuration. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.6.1.1 | ColumntnAceArpSmacFilter | read-write | current | Specify the source MAC filter for this ACE. any: No SMAC filter is specified. (SMAC filter status is 'dont-care'.) specific: If you want to filter a specific s… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.6.1.2 | ColumntnAceArpSmacVal | read-write | current | When 'Specific' is selected for the SMAC/DMAC filter, you can enter a specific value. The legal format is 'xx-xx-xx-xx-xx-xx' or 'xx.xx.xx.xx.xx.xx' or 'xxxxxx… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.6.1.3 | ColumntnAceArpDmacFilter | read-write | current | Specify the destination MAC filter for this ACE. any: No DMAC filter is specified. (DMAC filter status is 'dont-care'.) unicast: Frame must be unicast. multica… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.6.1.4 | ColumntnAceArpParmArpRarp | read-write | current | Specify the available ARP/RARP opcode (OP) flag for this ACE. any: No ARP/RARP OP flag is specified. (OP is 'dont-care'.) arp: Frame must have ARP/RARP opcode … |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.6.1.5 | ColumntnAceArpParmRequestReply | read-write | current | Specify the available requset/reply opcode (OP) flag for this ACE. any: No ARP/RARP OP flag is specified. (OP is 'dont-care'.) request: Frame must have ARP Req… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.6.1.6 | ColumntnAceArpParmSenderIpFilter | read-write | current | Specify the sender IP filter for this ACE. any: No sender filter is specified. (sender ip filter status is 'don't-care'.) host: If you want to filter a specifi… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.6.1.7 | ColumntnAceArpParmSenderIpAddress | read-write | current | When 'Host' or 'Network' is selected for the sender ip filter, you can enter a specific host or network address. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.6.1.8 | ColumntnAceArpParmSenderIpMask | read-write | current | When 'Network' is selected for the sender ip filter, you can enter a specific network mask. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.6.1.9 | ColumntnAceArpParmTargetIpFilter | read-write | current | Specify the target IP filter for this ACE. any: No sender filter is specified. (target ip filter status is 'don't-care'.) host: If you want to filter a specifi… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.6.1.10 | ColumntnAceArpParmTargetIpAddress | read-write | current | When 'Host' or 'Network' is selected for the target ip filter, you can enter a specific host or network address. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.6.1.11 | ColumntnAceArpParmTargetIpMask | read-write | current | When 'Network' is selected for the target ip filter, you can enter a specific network mask. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.6.1.12 | ColumntnAceArpSenderMacMatch | read-write | current | Specify whether frames can hit the action according to their sender hardware address field (SHA) settings. 0: ARP frames where SHA is not equal to the SMAC add… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.6.1.13 | ColumntnAceArpRarpTargetMacMatch | read-write | current | Specify whether frames can hit the action according to their target hardware address field (THA) settings. 0: RARP frames where THA is not equal to the SMAC ad… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.6.1.14 | ColumntnAceArpIpEthernetLength | read-write | current | Specify whether frames can hit the action according to their ARP/RARP hardware address length (HLN) and protocol address length (PLN) settings. 0: ARP/RARP fra… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.6.1.15 | ColumntnAceArpIp | read-write | current | Specify whether frames can hit the action according to their ARP/RARP hardware address space (HRD) settings. 0: ARP/RARP frames where the HLD is not equal to E… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.6.1.16 | ColumntnAceArpEthernet | read-write | current | Specify whether frames can hit the action according to their ARP/RARP protocol address space (PRO) settings. 0: ARP/RARP frames where the PRO is not equal to I… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.7 | TabletnAceIpv4Table | not-accessible | current | This table contains the related configuration of ACE when frame type is IPv4. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.7.1 | RowtnAceIpv4Entry | not-accessible | current | This entry represents an IPv4 related ACE configuration. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.7.1.1 | ColumntnAceIpv4ProtoFilter | read-write | current | Specify the IP protocol filter for this ACE. any: No IP protocol filter is specified. (Protocol filter status is 'don't-care'.) other: If you want to filter a … |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.7.1.2 | ColumntnAceIpv4ProtoValue | read-write | current | When 'Specific' is selected for the IP protocol value, you can enter a specific value. The allowed range is 0 to 255. A frame that hits this ACE matches this I… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.7.1.3 | ColumntnAceIpv4Ttl | read-write | current | Specify the Time-to-Live settings for this ACE. zero: IPv4 frames with a Time-to-Live field greater than zero must not be able to match this entry. nonZero: IP… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.7.1.4 | ColumntnAceIpv4Fragment | read-write | current | Specify the fragment offset settings for this ACE. This involves the settings for the More Fragments (MF) bit and the Fragment Offset (FRAG OFFSET) field for a… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.7.1.5 | ColumntnAceIpv4Option | read-write | current | Specify the options flag setting for this ACE. any: Any value is allowed ('don't-care'). yes: IPv4 frames where the options flag is set must be able to match t… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.7.1.6 | ColumntnAceIpv4SipFilter | read-write | current | Specify the source IP filter for this ACE. any: No source IP filter is specified. (source ip filter is 'don't-care'.) host: Source IP filter is set to Host. Sp… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.7.1.7 | ColumntnAceIpv4SipAddress | read-write | current | When 'Host' or 'Network' is selected for the source ip filter, you can enter a specific host or network address. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.7.1.8 | ColumntnAceIpv4SipMask | read-write | current | When 'Network' is selected for the source ip filter, you can enter a specific network mask. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.7.1.9 | ColumntnAceIpv4DipFilter | read-write | current | Specify the destination IP filter for this ACE. any: No destination IP filter is specified. (source ip filter is 'don't-care'.) host: Destination IP filter is … |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.7.1.10 | ColumntnAceIpv4DipAddress | read-write | current | When 'Host' or 'Network' is selected for the destination ip filter, you can enter a specific host or network address. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.7.1.11 | ColumntnAceIpv4DipMask | read-write | current | When 'Network' is selected for the destination ip filter, you can enter a specific network mask. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.7.1.12 | ColumntnAceIpv4IcmpTypeFilter | read-write | current | Specify the ICMP filter for this ACE. any: No ICMP filter is specified. (ICMP filter status is 'dont-care'.) specific: If you want to filter a specific ICMP fi… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.7.1.13 | ColumntnAceIpv4IcmpTypeValue | read-write | current | When 'Specific' is selected for the ICMP filter, you can enter a specific ICMP value. The allowed range is 0 to 255. A frame that hits this ACE matches this IC… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.7.1.14 | ColumntnAceIpv4IcmpCodeFilter | read-write | current | Specify the ICMP code filter for this ACE. any: No ICMP code is specified. (ICMP filter status is 'dont-care'.) specific: If you want to filter a specific ICMP… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.7.1.15 | ColumntnAceIpv4IcmpCodeValue | read-write | current | When 'Specific' is selected for the ICMP code filter, you can enter a specific ICMP code value. The allowed range is 0 to 255. A frame that hits this ACE match… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.7.1.16 | ColumntnAceIPv4SrcPortFilterType | read-write | current | The TCP/UDP source port for matching the ACE. It only significant if protocol filter 'UDP' or 'TCP' is selected. The possible values are: any: No TCP/UDP sourc… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.7.1.17 | ColumntnAceIPv4SrcPortFilterNo | read-write | current | When 'Specific' is selected for the source port filter, you can enter a specific value. The allowed value is from 0 through 65535. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.7.1.18 | ColumntnAceIPv4SrcPortRangeStart | read-write | current | When 'Range' is selected for the source port filter, you can enter a specific range. The allowed range start is from 0 through 65535. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.7.1.19 | ColumntnAceIPv4SrcPortRangeEnd | read-write | current | When 'Range' is selected for the source port filter, you can enter a specific range. The allowed range end is from 0 through 65535. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.7.1.20 | ColumntnAceIPv4DstPortFilterType | read-write | current | The TCP/UDP destination port for matching the ACE. It only significant if protocol filter 'UDP' or 'TCP' is selected. The possible values are: any: No TCP/UDP … |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.7.1.21 | ColumntnAceIPv4DstPortFilterNo | read-write | current | When 'Specific' is selected for the destination port filter, you can enter a specific value. The allowed value is from 0 through 65535. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.7.1.22 | ColumntnAceIPv4DstPortRangeStart | read-write | current | When 'Range' is selected for the destination port filter, you can enter a specific range. The allowed range start is from 0 through 65535. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.7.1.23 | ColumntnAceIPv4DstPortRangeEnd | read-write | current | When 'Range' is selected for the destination port filter, you can enter a specific range. The allowed range end is from 0 through 65535. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.7.1.24 | ColumntnAceIPv4TcpFin | read-write | current | Specify the TCP 'No more data from sender' (FIN) value for this ACE. 0: TCP frames where the FIN field is set must not be able to match this entry. 1: TCP fram… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.7.1.25 | ColumntnAceIPv4TcpSyn | read-write | current | Specify the TCP 'Synchronize sequence numbers' (SYN) value for this ACE. 0: TCP frames where the SYN field is set must not be able to match this entry. 1: TCP … |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.7.1.26 | ColumntnAceIPv4TcpRst | read-write | current | Specify the TCP 'Reset the connection' (RST) value for this ACE. 0: TCP frames where the RST field is set must not be able to match this entry. 1: TCP frames w… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.7.1.27 | ColumntnAceIPv4TcpPsh | read-write | current | Specify the TCP 'Push Function' (PSH) value for this ACE. 0: TCP frames where the PSH field is set must not be able to match this entry. 1: TCP frames where th… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.7.1.28 | ColumntnAceIPv4TcpAck | read-write | current | Specify the TCP 'Acknowledgment field significant' (ACK) value for this ACE. 0: TCP frames where the ACK field is set must not be able to match this entry. 1: … |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.7.1.29 | ColumntnAceIPv4TcpUrg | read-write | current | Specify the TCP 'Urgent Pointer field significant' (URG) value for this ACE. 0: TCP frames where the URG field is set must not be able to match this entry. 1: … |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.8 | TabletnAclStatusTable | not-accessible | current | This table shows the ACL status by different ACL users. Each row describes the ACE that is defined. It is a conflict if a specific ACE is not applied to the ha… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.8.1 | RowtnAclStatusEntry | not-accessible | current | This entry represents ACL status by different ACL users. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.8.1.1 | ColumntnAclStatusUser | not-accessible | current | Indicates the ACL user. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.8.1.2 | ColumntnAclStatusIngressPort | read-only | current | Indicates the ingress port of the ACE. Possible values are: All: The ACE will match all ingress port. Port: The ACE will match a specific ingress port. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.8.1.3 | ColumntnAclStatusFrameType | read-only | current | Indicates the frame type of the ACE. Possible values are: Any: The ACE will match any frame type. EType: The ACE will match Ethernet Type frames. Note that an … |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.8.1.4 | ColumntnAclStatusEtypeVal | read-only | current | Indicates the type value when frame type of the ACE is Ethernet Type. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.8.1.5 | ColumntnAclStatusAction | read-only | current | Indicates the forwarding action of the ACE. Permit: Frames matching the ACE may be forwarded and learned. Deny: Frames matching the ACE are dropped. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.8.1.6 | ColumntnAclStatusRateLimiter | read-only | current | Indicates the rate limiter number of the ACE. The allowed range is 1 to 16. When Disabled is displayed, the rate limiter operation is disabled. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.8.1.7 | ColumntnAclStatusPortRedirect | read-only | current | Indicates the port redirect operation of the ACE. Frames matching the ACE are redirected to the port number. The allowed values are Disabled or a specific port… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.8.1.8 | ColumntnAclStatusMirror | read-only | current | Specify the mirror operation of this port. The allowed values are: Enabled: Frames received on the port are mirrored. Disabled: Frames received on the port are… |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.8.1.9 | ColumntnAclStatusCpu | read-only | current | Forward packet that matched the specific ACE to CPU. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.8.1.10 | ColumntnAclStatusCpuOnce | read-only | current | Forward first packet that matched the specific ACE to CPU. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.8.1.11 | ColumntnAclStatusCounter | read-only | current | The counter indicates the number of times the ACE was hit by a frame. |
| 1.3.6.1.4.1.868.2.5.3.1.1.5.8.1.12 | ColumntnAclStatusConflict | read-only | current | Indicates the hardware status of the specific ACE. The specific ACE is not applied to the hardware due to hardware limitations. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| HostOrNetworkOrAny | INTEGER { any(1), host(2), network(3) } | current | Truth value 0/1 and any. |
| RateLimiterValue | Integer32 (0 | 1..16) | current | Rate limiter valid value. Here '0' means 'disabled'. |
| TruthValueOrAny | INTEGER { any(1), val0(2), val1(3) } | current | Truth value 0/1 and any. |