TN-ERPS-MIB
70 objects
No module-level DESCRIPTION found.
Imported Objects
| IEEE8021-CFM-MIB | Dot1agCfmMepId |
| IF-MIB | InterfaceIndex |
| Q-BRIDGE-MIB | VlanId |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Gauge32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DisplayString MacAddress RowStatus TruthValue |
| TN-PROTECTION-MIB | tnProtectionMIB |
| TRANSITION-SMI | tnProducts |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.868.2.5.109.3 | NodetnERPSMIB | |||
| 1.3.6.1.4.1.868.2.5.109.3.1 | NodetnERPSMIBNotifications | |||
| 1.3.6.1.4.1.868.2.5.109.3.1.1 | NotificationtnErpsAlarmUp | current | A ERPS has cleared a defect condition. A notification (fault clearance alarm) is sent to the management entity with the OID of the ERPS that has cleared the fa… | |
| 1.3.6.1.4.1.868.2.5.109.3.1.2 | NotificationtnErpsAlarmDown | current | A ERPS has a persistent defect condition. A notification (fault alarm) is sent to the management entity with the OID of the ERPS that has detected the fault. T… | |
| 1.3.6.1.4.1.868.2.5.109.3.2 | NodetnERPSMgmtObjects | |||
| 1.3.6.1.4.1.868.2.5.109.3.2.1 | TabletnERPSTable | not-accessible | current | This table displays and sets current Ethernet Protection Switching configurations. |
| 1.3.6.1.4.1.868.2.5.109.3.2.1.1 | RowtnERPSEntry | not-accessible | current | This entry represents an Ethernet Ring Protection Switching configuration. |
| 1.3.6.1.4.1.868.2.5.109.3.2.1.1.1 | ColumntnERPSinstance | not-accessible | current | The ID of the ERPS. |
| 1.3.6.1.4.1.868.2.5.109.3.2.1.1.2 | ColumntnERPSPort0 | read-create | current | This will create a Port 0 of the switch in the ring. |
| 1.3.6.1.4.1.868.2.5.109.3.2.1.1.3 | ColumntnERPSPort1 | read-create | current | This will create 'Port 1' of the switch in the Ring. As interconnected sub-ring will have only one ring port, 'Port 1' is configured as '0' for interconnected … |
| 1.3.6.1.4.1.868.2.5.109.3.2.1.1.4 | ColumntnERPSPort0ApsMep | read-create | current | The Port 0 APS PDU handling MEP. |
| 1.3.6.1.4.1.868.2.5.109.3.2.1.1.5 | ColumntnERPSPort1ApsMep | read-create | current | The Port 1 APS PDU handling MEP. As only one APS MEP is associated with interconnected sub-ring without virtual channel, it is configured as '0' for such ring … |
| 1.3.6.1.4.1.868.2.5.109.3.2.1.1.6 | ColumntnERPSPort0SfMep | read-create | current | The Port 0 Signal Fail reporting MEP. |
| 1.3.6.1.4.1.868.2.5.109.3.2.1.1.7 | ColumntnERPSPort1SfMep | read-create | current | The Port 1 Signal Fail reporting MEP. |
| 1.3.6.1.4.1.868.2.5.109.3.2.1.1.8 | ColumntnERPSRingType | read-create | current | Type of Protecting ring. It can be either major ring or sub-ring. As per G.8032v2, they are defined as : Major Ring: A Major ring is the Ethernet ring that is … |
| 1.3.6.1.4.1.868.2.5.109.3.2.1.1.9 | ColumntnERPSInterconnectednode | read-create | current | Interconnected Node indicates that the ring instance is interconnected. Click on the checkbox to configure this. 'True' indicates it is an interconnected node … |
| 1.3.6.1.4.1.868.2.5.109.3.2.1.1.10 | ColumntnERPSVirtualChannel | read-create | current | Sub-rings can either have virtual channel or not on the interconnected node. 'True' indicates it is a sub-ring with virtual channel. 'False' indicates, sub-rin… |
| 1.3.6.1.4.1.868.2.5.109.3.2.1.1.11 | ColumntnERPSMajorRingID | read-create | current | Major ring group ID for the interconnected sub-ring. It is used to send topology change updates on major ring. If ring is major, this value is same as the prot… |
| 1.3.6.1.4.1.868.2.5.109.3.2.1.1.12 | ColumntnERPSAlarm | read-only | current | There is an active alarm on the ERPS. |
| 1.3.6.1.4.1.868.2.5.109.3.2.1.1.13 | ColumntnERPSRowStatus | read-create | current | The rowstatus of the Ethernet Ring Protection Switch. |
| 1.3.6.1.4.1.868.2.5.109.3.2.2 | TabletnERPSConfigTable | not-accessible | current | This table contains the configuration of Instance Configuration. |
| 1.3.6.1.4.1.868.2.5.109.3.2.2.1 | RowtnERPSConfigEntry | not-accessible | current | This entry represents an ERPS. |
| 1.3.6.1.4.1.868.2.5.109.3.2.2.1.1 | ColumntnERPSConfigStatus | read-only | current | Red: This ERPS is only created and has not yet been configured - is not active. Green: This ERPS is configured - is active�� |
| 1.3.6.1.4.1.868.2.5.109.3.2.2.1.2 | ColumntnERPSConfigGuardTime | read-write | current | Guard timeout value to be used to prevent ring nodes from receiving outdated R-APS messages. The period of the guard timer can be configured in 10 ms steps bet… |
| 1.3.6.1.4.1.868.2.5.109.3.2.2.1.3 | ColumntnERPSConfigWtrTime | read-write | current | The Wait To Restore timing value to be used in revertive switching. The period of the WTR time can be configured by the operator in 1 minute steps between 1 an… |
| 1.3.6.1.4.1.868.2.5.109.3.2.2.1.4 | ColumntnERPSConfigHoldOffTime | read-write | current | The timing value to be used to make persistent check on Signal Fail before switching. The range of the hold off timer is 0 to 10 seconds in steps of 100 ms |
| 1.3.6.1.4.1.868.2.5.109.3.2.2.1.5 | ColumntnERPSConfigVersion | read-write | current | Select v1 or v2 as the ERPS version to be used. For fields such as Version, OpCode, Flags, and End TLV, the values used are as defined in ITU-T Y.1731 (Version… |
| 1.3.6.1.4.1.868.2.5.109.3.2.2.1.6 | ColumntnERPSConfigRevertive | read-write | current | In Revertive mode, after the conditions causing a protection switch has cleared, the traffic channel is restored to the working transport entity, i.e., blocked… |
| 1.3.6.1.4.1.868.2.5.109.3.2.3 | TabletnERPSRPLTable | not-accessible | current | This table contains the configuration of RPL Configuration. |
| 1.3.6.1.4.1.868.2.5.109.3.2.3.1 | RowtnERPSRPLEntry | not-accessible | current | This entry represents an RPL. |
| 1.3.6.1.4.1.868.2.5.109.3.2.3.1.1 | ColumntnERPSRPLRole | read-write | current | It can be either RPL owner or RPL Neighbour. |
| 1.3.6.1.4.1.868.2.5.109.3.2.3.1.2 | ColumntnERPSRPLPort | read-write | current | This allows to select the east port or west port as the RPL block. |
| 1.3.6.1.4.1.868.2.5.109.3.2.3.1.3 | ColumntnERPSRPLClear | read-write | current | If the owner has to be changed, then the clear check box allows to clear the RPL owner for that ERPS ring. |
| 1.3.6.1.4.1.868.2.5.109.3.2.4 | TabletnERPSCommandTable | not-accessible | current | This table contains the configuration of Command Configuration. |
| 1.3.6.1.4.1.868.2.5.109.3.2.4.1 | RowtnERPSCommandEntry | not-accessible | current | This entry represents an Command. |
| 1.3.6.1.4.1.868.2.5.109.3.2.4.1.1 | ColumntnERPSCommand | read-write | current | Administrative command. A port can be administratively configured to be in either manual switch or forced switch state. |
| 1.3.6.1.4.1.868.2.5.109.3.2.4.1.2 | ColumntnERPSCommandPort | read-write | current | Port selection - Port0 or Port1 of the protection Group on which the command is applied. |
| 1.3.6.1.4.1.868.2.5.109.3.2.5 | TabletnERPSStateTable | not-accessible | current | This table contains the configuration of EVC control entry. |
| 1.3.6.1.4.1.868.2.5.109.3.2.5.1 | RowtnERPSStateEntry | not-accessible | current | This entry represents an instance State. |
| 1.3.6.1.4.1.868.2.5.109.3.2.5.1.1 | ColumntnERPSState | read-only | current | ERPS state according to State Transition Tables in G.8032. |
| 1.3.6.1.4.1.868.2.5.109.3.2.5.1.2 | ColumntnERPSStatePort0 | read-only | current | OK: State of East port is ok. SF: State of East port is Signal Fail. |
| 1.3.6.1.4.1.868.2.5.109.3.2.5.1.3 | ColumntnERPSStatePort1 | read-only | current | OK: State of East port is ok. SF: State of East port is Signal Fail. |
| 1.3.6.1.4.1.868.2.5.109.3.2.5.1.4 | ColumntnERPSStateTxAps | read-only | current | The transmitted APS according to State Transition Tables in G.8032. |
| 1.3.6.1.4.1.868.2.5.109.3.2.5.1.5 | ColumntnERPSStatePort0RxAps | read-only | current | The received APS on Port 0 according to State Transition Tables in G.8032. |
| 1.3.6.1.4.1.868.2.5.109.3.2.5.1.6 | ColumntnERPSStatePort1RxAps | read-only | current | The received APS on Port 1 according to State Transition Tables in G.8032. |
| 1.3.6.1.4.1.868.2.5.109.3.2.5.1.7 | ColumntnERPSStateWtrRemaining | read-only | current | Remaining WTR timeout in milliseconds |
| 1.3.6.1.4.1.868.2.5.109.3.2.5.1.8 | ColumntnERPSStateRPLUnBlocked | read-only | current | APS is received on the working flow. |
| 1.3.6.1.4.1.868.2.5.109.3.2.5.1.9 | ColumntnERPSStateNoApsReceived | read-only | current | RAPS PDU is not received from the other end. |
| 1.3.6.1.4.1.868.2.5.109.3.2.5.1.10 | ColumntnERPSStatePort0Blockstatus | read-only | current | Block status for Port 0 (Both traffic and R-APS block status). R-APS channel is never blocked on sub-rings without virtual channel. |
| 1.3.6.1.4.1.868.2.5.109.3.2.5.1.11 | ColumntnERPSStatePort1Blockstatus | read-only | current | Block status for Port 1 (Both traffic and R-APS block status). R-APS channel is never blocked on sub-rings without virtual channel |
| 1.3.6.1.4.1.868.2.5.109.3.2.5.1.12 | ColumntnERPSStateFopAlarm | read-only | current | Failure of Protocol Defect(FOP) status. If FOP is detected, the red LED lights; otherwise the green LED lights. |
| 1.3.6.1.4.1.868.2.5.109.3.2.6 | TabletnERPSVlanTable | not-accessible | current | This table contains the configuration of vlan Configuration. |
| 1.3.6.1.4.1.868.2.5.109.3.2.6.1 | RowtnERPSVlanEntry | not-accessible | current | This entry represents an vlan. |
| 1.3.6.1.4.1.868.2.5.109.3.2.6.1.1 | ColumntnERPSVlanInstance | not-accessible | current | The instance of the ERPS vlan. |
| 1.3.6.1.4.1.868.2.5.109.3.2.6.1.2 | ColumntnERPSVlanId | read-write | current | vlan id. |
| 1.3.6.1.4.1.868.2.5.109.3.2.6.1.3 | ColumntnERPSVlanRowStatus | read-write | current | row status. |
| 1.3.6.1.4.1.868.2.5.109.3.2.7 | TabletnERPSSubRingCfgTable | not-accessible | current | This table contains the configuration of Command Configuration. |
| 1.3.6.1.4.1.868.2.5.109.3.2.7.1 | RowtnERPSSubRingCfgEntry | not-accessible | current | This entry represents an sub ring configuration. |
| 1.3.6.1.4.1.868.2.5.109.3.2.7.1.1 | ColumntnERPSSubRingType | read-only | current | erps ring type. |
| 1.3.6.1.4.1.868.2.5.109.3.2.7.1.2 | ColumntnERPSSubRingTopologyChange | read-write | current | Clicking this checkbox indicates that the topology changes in the sub-ring are propagated in the major ring. |
| 1.3.6.1.4.1.868.2.5.109.3.2.8 | TabletnERPSStatisticsTable | not-accessible | current | This table contains the display of erps statistics. |
| 1.3.6.1.4.1.868.2.5.109.3.2.8.1 | RowtnERPSStatisticsEntry | not-accessible | current | This entry represents an sub ring configuration. |
| 1.3.6.1.4.1.868.2.5.109.3.2.8.1.1 | ColumntnERPSRAPSPDUReceived | read-only | current | erps R-APS PDU received. |
| 1.3.6.1.4.1.868.2.5.109.3.2.8.1.2 | ColumntnERPSRAPSPDUDropped | read-only | current | erps R-APS PDU dropped. |
| 1.3.6.1.4.1.868.2.5.109.3.2.8.1.3 | ColumntnERPSLocalSFOccurred | read-only | current | erps local SF occurred. |
| 1.3.6.1.4.1.868.2.5.109.3.2.8.1.4 | ColumntnERPSLocalSFCleared | read-only | current | erps local SF cleared. |
| 1.3.6.1.4.1.868.2.5.109.3.2.8.1.5 | ColumntnERPSRemoteSFReceived | read-only | current | erps remote SF received. |
| 1.3.6.1.4.1.868.2.5.109.3.2.8.1.6 | ColumntnERPSRemoteFSReceived | read-only | current | erps remote FS received. |
| 1.3.6.1.4.1.868.2.5.109.3.2.8.1.7 | ColumntnERPSNRMessageSent | read-only | current | erps NR message sent. |
| 1.3.6.1.4.1.868.2.5.109.3.3 | NodetnERPSMIBConformance |